Brushbond RFX PDF
Brushbond RFX PDF
Water 3L 1L
Technical Support
Brushbond RFX
observed. Use a short stiff brush preferably 120-150mm Consistency Brush application
width and apply the mixed material like paint.
Coverage (15kg + 4.8 lit pack) 12 - 14m2
The application of Brushbond RFX should not be done if the
temperature of the substrate is below 100C. When applying Coverage (5 + 1.63 lit pack) 4 - 4.5m2
Brushbond RFX on hot substrates i.e., over 300C surface
Storage
temperature, saturate the surface with water. Apply Brushbond
RFX in 2 coats to achieve 1mm thickness. The second coat of Shelf life
Brushbond RFX shall be applied as soon as the first coat has
reached touch dry state. It is recommended that for general 6 months in unopened packs if kept in a dry store.
surfacing Brushbond RFX should be applied at a minimum Precautions
thickness of 1mm. Areas subjected to moderate and heavy
loads/hydrostatic pressure, minimum 2mm thickness coating Health and Safety instruction
is recommended with screed above.
Brushbond RFX is non-toxic but alkaline in nature. Gloves
Allow the Brushbond RFX coating to dry before covering with and goggles should be worn. Any splashes to the skin or
screed. Sprinkle coarse sand on wet surface of final coating for eyes should be washed off with clean water. In the event of
better adhesion of screed. prolonged irritation, seek medical advice. Use a dust mask
while handling the powder.
Average drying time is 4 to 6 hours at normal temperatures.
Cleaning Fire
Brushbond RFX should be removed from tools and equipment Brushbond RFX components are non inflammable.
with clean water immediately after use. Hardened material can
only be removed mechanically. Additional Information
Estimating The Fosroc range of associated products includes high strength
cementitious, epoxy grout, polyester resin based mortar for
Packing
rapid presetting of steel shims to level or for direct bedding of
Powder component : 15kg & 5kg packs small base plates; Resin Anchoring systems for same day
Liquid polymer component : 4.8 & 1.63 L containers anchoring of bolts in drilled holes in concrete or rock. Also
available a range of products for use in construction; viz.,
Coverage admixtures, curing compounds, release agents, flooring
This depends on the required consistency. The approximate systems and repair mortars.
coverage per pack at even consistency (1mm thickness) is as
Separate datasheets are available on these products.
follows
® Denotes the trademark of Fosroc International Limited
Important note :
Fosroc products are guaranteed against defective materials and manufacture and are sold subject
to its standard terms and conditions of sale, copies of which may be obtained on request. Whilst
Fosroc endeavours to ensure that any advice, recommendation specification or information it may
give is accurate and correct, it cannot, because it has no direct or continuous control over where
or how its products are applied, accept any liability either directly or indirectly arising from the
use of its products whether or not in accordance with any advice, specification, recommendation
Fosroc Chemicals (India) Pvt. Ltd. or information given by it.
Ahmedabad : (079) 26762799 Ankleshwar :(02646) 220704/224687 Bhubaneshwar : (0674) 2521176 Chennai (044) 24899949/24853383
Chandigarh : (0172) 2639360 Cochin : (0484) 2356668 Coimbatore : (0422) 2472966 Goa : (0832) 2542465 Guwahati (0361) 2548793
Hyderabad : (040) 27662324/27662425 Hubli (0836) 3402597 Indore : (0731) 504339/5061477 Jaipur : (0141) 2235349 Lucknow :(0522)
22239044 Nagercoil (04652) 2224849 Mangalore: (0824) 22272234 Visakhapatnam : (0891) 2564850
INDIA/2004/708/C