8 Inch Model 380/381 Control Valves: Technical Sales Bulletin
8 Inch Model 380/381 Control Valves: Technical Sales Bulletin
8 Inch Model 380/381 Control Valves: Technical Sales Bulletin
Features
Versatility
A wide range of trim options including Low Noise and
Anti-Cavitation make the 380 a highly versatile control
valve.
SPECIFICATIONS
Configurations Characteristics
Refer to Table 1. • Equal Percentage (Standard)
Trim Materials
Refer to Table 6.
Shutoff Classifications
Refer to Table 1.
Materials
Body and bonnet material options include:
LCC (A350-LF2 optional* bonnet material)
Dimensions
Valve Dimensions WCC (A350-LF2 optional* bonnet material)
Refer to Table 3 and Figure 2. CF8M (A182-F316 optional* bonnet material)
*NOTE: Dyna-Flo reserves the right to substitute a cast
material with the forged bar equivalent in the event a casting
is not available.
Approximate Valve Body Weights
Refer to Table 2. Refer to Figure 8. Refer to Tables 4 & 5 for typical
construction materials. Refer to Table 8 for trim selections.
Table 1
Valve Design Configurations
Valve Model Shut Off Class Capability Valve Plug Guide Seat
(in accordance with ANSI / FCI 70.2)
Table 2
Approximate Weights lb (kg)
Body
Class Flanged (RF/RTJ) Buttweld (BWE)
Table 3
Models 380 & 381 Standard Valve Dimensions Inches (mm) (Refer to Figure 2)
Dimension
Valve Size End Connection
A G B C
8” 900 RTJ 44.88 (1140) 16.94 (430) 14.31 (363) 26.94 (684)
1500 RTJ 47.38 (1203) 18.19 (462) 14.31 (363) 26.94 (684)
ACTUATOR
MATCH LINE
FLANGED END
CONNECTIONS
G ACTUATOR
MATCH LINE
A
BUTTWELD
(BWE) END
CONNECTIONS B
G
A
Dyna-Flo Control Valve Services Ltd. P-388B0319A
4
Phone: 780 • 469 • 4000 Toll Free: 1 • 866 • 396 • 2356 Fax: 780 • 469 • 4035 Website: www.dynaflo.com
8 Inch Model 380/381 Control Valves
Technical Sales Bulletin
FOLLOWER
LANTERN RING FLOW DOWN
PACKING SET
LOWER WIPER
PACKING BOX RING
BONNET STUD DETAIL A
FLOW UP
BONNET NUT
SEAL RING
BONNET
BODY
VALVE CAGE
SEAT RING
CAP SCREW
SEAT RING
Figure 4 Detail B - Seat Ring O-Ring Figure 5 Detail B - Seat Ring Gasket
STEM
RETAINING RING
BACKUP RING
SPRING-LOADED STEM
SEAL RING
Figure 6 Detail A - Model 380 Plug Seal Options Figure 7 Model 381 Plug and Cage Design
UPPER STEM
UPPER STEM WIPER UPPER STEM WIPER
WIPER
PACKING FOLLOWER PACKING FOLLOWER
SPRING
PTFE V-RING
PACKING BOX RING PACKING SET
PACKING SPRING
SPRING
FLANGE WASHERS
PACKING FOLLOWER WASHERS
PACKING
GUIDE BUSHING FOLLOWER
GRAPHITE FILAMENT COMPOSITE
PACKING RING
GRAPHITE ANTI-EXTRUSION PTFE V-RING
PACKING
RIBBON WASHER RINGS PACKING SET
GRAPHITE FILAMENT LAMINATE
COMPOSITE
PACKING RING
PACKING RING
LANTERN RING
LANTERN RINGS
GUIDE BUSHING
Table 4
Common Valve Parts Typical Construction Materials and Temperature Limitations
Temperature Limitations
Part Material
Min. OF Max. OF Min. OC Max. OC
Valve Stem S20910 NLF(1) NLF(1) NLF(1) NLF(1)
Cage Gasket N04400 NLF(1) NLF(1)
NLF(1) NLF(1)
Spring-Loaded Backup Ring S31600/S31603 Dual Grade NLF(1) NLF(1) NLF(1) NLF(1)
(Three-Piece) Seal Ring PTFE / Elgiloy -100 450 -73 232
Valve Plug Seal
(Model 380 Only) Retaining Ring S31600 NLF(1) NLF(1) NLF(1) NLF(1)
Spring-Loaded Anti-Extrusion Ring PolyEtherEtherKetone (PEEK) NLF(1) NLF(1) NLF(1) NLF(1)
(Three-Piece) Backup Ring S31600/S31603 Dual Grade NLF(1) NLF(1) NLF(1) NLF(1)
Valve Plug Seal Seal Ring PTFE / Elgiloy -100 600 -73 319
with
Anti-Extrusion Rings Retaining Ring S31600 NLF(1) NLF(1) NLF(1) NLF(1)
(Model 380 Only)
Piston Ring (Model 381 Only) Graphite NLF(1) 1100(4) NLF(1) 593(4)
Viton(2) -10 400 -23 204
Nitrile (NACE) -20 225 -29 107
Seat Ring O-Ring
Ethylene-Propylene (EPDM) -40 450 -40 232
(Anti-Cavitation, NACE)
Seat Ring Gasket N06600 / Graphite NLF(1) NLF(1) NLF(1) NLF(1)
PTFE V-Ring -40 450 -40 232
Packing
Graphite (Ribbon/Filament) -425 1000(3) -254 538(3)
NOTES:
1 - NLF - This Material is Not A Limiting Factor. For the temperature limitation refer to the valve body material temperature limit.
2 - Standard option, not for water or steam service. Fluoroelastomer is limited to 300OF (149OC) when used for NACE.
3 - Oxidizing service limited to 700OF (371OC).
4 - Oxidizing service limited to 1000OF (538OC).
Table 5
Body to Bonnet Bolting Temperature Limitations
Bolt/Nut Temperature Limitations
Body Material ASME Class Material Min. OF Max. OF Min. OC Max. OC
B7/2H (1)(2)
-50 650 -46 343
LCC 150/300/600
B7M/2HM(3) -50 650 -46 343
B7/2H(1)(2) -20 800 -29 427
WCC 150/300/600
B7M/2HM(3) -20 800 -29 427
B7 Fluorokote #1 / 2H Fluorokote #1
-50 500 -46 260
(Standard)(2)
CF8M 150/300/600
B8M/8M (2)
-325 800 -198 427
B7M Fluorokote #1/ 2HM Fluorokote #1(3) -20 500 -29 260
NOTES:
1 - Standard non-NACE option.
2 - NACE MR0175/ISO15156 Non-Exposed Bolting option (Bolting that is not directly exposed to sour environments and is not to be buried,
insulated, equipped with flange protectors, or otherwise denied direct atmospheric exposure).
3 - NACE MR0175/ISO15156 Exposed Bolting option (Bolting that will be exposed directly to the sour environment or that will be buried, insulated,
equipped with flange protectors, or otherwise denied direct atmospheric exposure).
TEMPERATURE (°C)
LCC -46 38 93 149 204 260 316 371 427
STEEL VALVE 3,750 25,885
TEMPERATURE (°C)
CF8M -29 38 93 149 204 260 316 371 427 482 538
STAINLESS 3,750 25,885
Maximum Inlet Temperature and Pressures - Valves consistent with ASME Class rating as per ASME B16.34, unless limited by
either material, pressure or temperature limitations.
Figure 9 Pressure / Temperature Charts as per ASME B16.34 (Continued on Page 10)
TEMPERATURE (°C)
WCC -29 38 93 149 204 260 316 371 427
STEEL VALVE 3,750 25,885
Figure 9 Pressure / Temperature Charts as per ASME B16.34 (Continued from Page 9)
Table 6
Common Trim Options and Temperature Ratings
Minimum(1) Maximum(1)
Temperature Temperature
Trim Spec(2) Valve Plug Stem Cage Seat Ring
o
F (oC) o
F (oC)
S17400
S S41600 HT S20910 S41600 HT -20 (-29) 800 (427)
H900
S31600(3) / S31600(3) /
C S20910 S31600(3) ENC -325 (-46) 650 (343)
Alloy 6 Seat and Guide Alloy 6
1 - Temperatures need to be considered when specifying trim materials for elevated temperatures in corrosive environments,
consult factory for further information.
Table 7
Maximum Sizing Coefficients
Full Port
Equal Percentage Characteristic
Globe Body Valve
Flow Down
NOTE: For the complete list of sizing coefficients refer to catalogue P-CVSM.
Neither Dyna-Flo Control Valve Services Ltd., nor any of their affiliated entities assumes responsibility for the selection, use
and maintenance of any product. Responsibility for selection, use and maintenance of any product remains with the purchaser
and end-user.
VALVE MODEL
380
380 380 381 381
VALVE SIZE
8
8 8 INCH
ASME RATING
B
A 900 B 1500
END CONNECTION
F RF J RTJ B BUTTWELD (SCHEDULE 80) F
U BUTTWELD (SCHEDULE 120) P BUTTWELD (SCHEDULE 160)
BODY MATERIAL
L
L LCC M CF8M W WCC
BOLTING
- B7 / 2H (STANDARD) A B7M / 2HM
-
B B8M / 8M K B7 FLUOROKOTE #1 / 2H FLUOROKOTE #1
L B7M FLUOROKOTE #1 / 2HM FLUOROKOTE #1
TRIM
S TRIM SPEC S C TRIM SPEC C S
N TRIM SPEC N
SEAT RING GASKET / O-RING
G GASKET (N06600 / GRAPHITE) E O-RING (EPDM) V
N O-RING (NITRILE) V O-RING (VITON) STANDARD
PACKING STYLE
P SINGLE PTFE V-RING (PRESSURE) J DOUBLE PTFE V-RING (PRESSURE)
G SINGLE GRAPHITE (PRESSURE) V DOUBLE PTFE V-RING (VACUUM)
P
R DOUBLE PTFE V-RING (VACUUM / PRESSURE) L LIVE LOADED PTFE V-RING (PRESSURE)
T LIVE LOADED GRAPHITE (PRESSURE) D LIVE LOADED DUPLEX (PRESSURE)
K LIVE LOADED KALREZ®
YOKE BOSS SIZE / VALVE STEM DIAMETER
5
5 5” (127 mm) / 1” (25.4 mm) H 5H - 5” (127 mm) / 1-1/4” (31.8 mm)
PAINT
- DFPS-01 (STANDARD) 2 DFPS-02 (SEVERE SERVICE) -
3 DFPS-03 (HIGH TEMPERATURE)
BACKUP RING / PISTON RING
C S31600 / PTFE-ELGILOY R S31600 / PTFE-ELGILOY WITH PEEK AE RINGS C
P PISTON RING - GRAPHITE (MODEL 381 ONLY)
CHARACTERISTIC
E
E EQUAL PERCENT L LINEAR M MODIFIED EQUAL PERCENT
BONNET STYLE
S
S STANDARD T STANDARD TAPPED
SHUTOFF CLASS
4
4 IV 5 V
NOTE: Modified Equal Percent is a factor of travel and requires no special parts or trim options that
differ from Equal Percent.