Foxboro™ SCADA

SCD6000 CPU OptoNet Power Supply Ethernet (COPE)

Module / SCD6000 CPU OptoNet Ethernet (COE)
Module

PSS 41H-8K2
Product Specification

March 2020

https://www.se.com
Legal Information
The Schneider Electric brand and any trademarks of Schneider Electric SE and its
subsidiaries referred to in this guide are the property of Schneider Electric SE or its
subsidiaries. All other brands may be trademarks of their respective owners.
This guide and its content are protected under applicable copyright laws and furnished
for informational use only. No part of this guide may be reproduced or transmitted in
any form or by any means (electronic, mechanical, photocopying, recording, or
otherwise), for any purpose, without the prior written permission of Schneider Electric.
Schneider Electric does not grant any right or license for commercial use of the guide
or its content, except for a non-exclusive and personal license to consult it on an "as is"
basis. Schneider Electric products and equipment should be installed, operated,
serviced, and maintained only by qualified personnel.
As standards, specifications, and designs change from time to time, information
contained in this guide may be subject to change without notice.
To the extent permitted by applicable law, no responsibility or liability is assumed by
Schneider Electric and its subsidiaries for any errors or omissions in the informational
content of this material or consequences arising out of or resulting from the use of the
information contained herein.
 SCD6000 CPU OptoNet Power Supply Ethernet (COPE) Module
Overview / SCD6000 CPU OptoNet Ethernet (COE) Module

Overview
The EcoStruxure™ Foxboro™ SCADA SCD6000 CPU COPE/COE module inherits the
functionality of the compact Foxboro SCADA SCD5200 COPE/COE module. When
this module is used in an SCD6000 IEC 61850 Gateway, it provides more dynamic
RAM for a higher concentration of IEC 61850 Intelligent Electronic Devices (IEDs).
The SCD6000 processor uses SFP receptacles to provide means of connection to the
local area networks.

Introduction
Modularity is the key feature of SCD6000. The CPU module is made up of:
• High Speed board
• Carrier board
• Power Supply board (COPE) (add-on board)
These three boards are integrated into a compact main processor board. In a
distributed station computing device network, the COPE module is the heart of each
node, where each COPE node manages its associated database, communications,
and local applications. When utilized as a Data Control and Interchange Unit (DCIU),
the COPE module provides:
• Data concentration capability
• SCADA communication
• Communication with Intelligent Electronic Devices (IEDs) over RS-232/RS-485
• Two SFP receptacles allow to plug in either a Fiber SFP with a support of
100Base FX or a Copper SFP with a support of 10/100-Base-T and one 10/
100Base-T on RJ-45 Ethernet links
With its on-board OptoNet fiber optic network connectivity, the COPE module supports
high performance and reliable peer-to-peer communication between the Station
Computing Devices (SCD) nodes.
The COE module is a variant of the COPE module without the Power Supply board.
The COE is used in the 10 I/O slot card file with a separate 65 W power supply.

PSS 41H-8K2, Rev A 3

SCD6000 CPU OptoNet Power Supply Ethernet (COPE) Module
/ SCD6000 CPU OptoNet Ethernet (COE) Module Features

Features
CPU
• Dual ARM Cortex A9 SoC
• 256 MB DDR3 SDRAM
• 256 KB non-volatile RAM parameter memory
• 16 MB protected mode BIOS
• 64 MB Internal Flash storage
• Dedicated RJ-45 Diagnostic Ethernet port
• Watchdog timer
• RS-232/RS-485 programmable Serial port
• Two SFP receptacles allow to plug in either a Fiber SFP with a support of
100Base FX or a Copper SFP with a support of 10/100Base-T
• Real-time calendar clock
• 7-year battery backup
OptoNet
• Dual ring network, with up to 63 nodes per network
• Deterministic, token-passing network protocol
• Total network length up to 5.8 km, maximum of 500 m between nodes
• Optical fiber (multi-mode glass) cables
• Fault tolerant to a single point of failure
• High speed data transfer
• Enables distributed data
• Availability of I/O data to all nodes
• Convenient low cost ST Tx and Rx connector
Power Supply (COPE only)
• Wide range input supply: 19.2 V to 148 V DC
• 40 W output capacity
• Compact high efficiency switch design
• Exhibits 4 ms hold up time with shorted input power
• Withstands 10 ms open circuit power input
• Over-current and over/under voltage protection
• Front panel LEDs to monitor input supply and internal voltage
• On-board power supply disconnected when external Wide Range Input Power
Supply module is used (Refer to PSS 41H-8K3R)
Ethernet
• Half/full duplex communications
• Two SFP ports provide link and activity indications for each channel, and support
either 100Base-FX or 10/100Base-T interface modules
• One port that supports 10/100Base-T Ethernet interface on the RJ-45, is
dedicated to EcoStruxure™ Foxboro™ SCADA Remote Terminal Viewer (RTV)
connectivity

4 PSS 41H-8K2, Rev A

 SCD6000 CPU OptoNet Power Supply Ethernet (COPE) Module
Functional Description / SCD6000 CPU OptoNet Ethernet (COE) Module

Functional Description
CPU
The SCD6000 CPU module is a combination of a High Speed CPU board and a
Carrier board. The High Speed CPU board has a SPEAr1380 processor with 2 X ARM
cortex A9 cores that support a frequency of 600 MHz.
The SCD6000 Carrier board has three Ethernet ports. Two of the ports are SFP ports
that support pluggable 100Base-FX or 10/100Base-T interface modules. The third
port supports a 10/100Base-T Ethernet interface on the RJ-45 connector.
A Serial port, which can be linked to RS-232 or RS-485, is available for interfacing
with IEDs or for communicating with a SCADA Master Station. This port supports an
industrial standard DNP3 Slave, DNP3 Master, Modbus Slave, and Modbus Master
protocols. It allows the implementation of proprietary protocols through the State And
Logic Language High Level Serial Interface (SALL HLSI). (Refer to PSS 41S-2M15 for
more information on SALL)
The Serial port supports logging of Sequence Of Events (SOE) to a printer or a
terminal.
OptoNet
OptoNet on the SCD6000 CPU module is essentially a three-port hub, with all three
ports controlled from a single ARCNET network controller chip. The two external ports
are logically and physically identical. Port A and Port B can be connected between
neighboring RTUs. These ports are half-duplex ports that can transmit and receive
data individually thereby, creating two effective “rings”.
The third port is also a half-duplex port that is logically identical to the other two. It is
an internal port that backs onto the ARCNET controller.
The RTU host processors configure the network automatically at the start-up, and are
assigned network addresses according to their OptoNet node number.
The ARCNET controller chips are the only local intelligence (processing unit) on the
OptoNet node modules and the RTU host processors direct the network activity. The
ARCNET controller chips handle all the housekeeping tasks such as passing tokens,
acknowledging messages, and checking for detected errors.
Power Supply
The COPE and COE variants of the SCD6000 CPU board are powered differently.
• The COPE variant is powered by its Power Supply board
• The COE variant is powered by the backplane that in turn is powered by a
standalone Power Supply module
The wide input range (19.2 V to 148 V DC) of the Power Supply subsystem allows the
SCD to be powered from 24 V, 48 V, or 129 V DC nominal power sources.
The Power Supply has a switched mode design that minimizes the size and weight of
the Power Supply module and offers high power conversion.
The Power Supply subsystem supplies power up to 40 W.
If suitable operating voltages are not available, built-in voltage monitors hold the SCD
in reset mode. A wide range 65 W Power Supply module is used to power a larger
card file configuration using the COPE or the COE module. (Refer to PSS 41H-8K3R
for more information).

PSS 41H-8K2, Rev A 5

SCD6000 CPU OptoNet Power Supply Ethernet (COPE) Module
/ SCD6000 CPU OptoNet Ethernet (COE) Module Functional Description

Ethernet
The SCD6000 module supports both half-duplex and full-duplex operations on
Ethernet. The SCD6000 CPU module features Ethernet ports:
• Two SFP ports to support either 100Base-FX or 10/100Base-T interface modules
• One 10/100Base-T Ethernet port on the RJ-45 connector
The SFP Ethernet ports provide a cost-effective and versatile fiber optic and copper
Ethernet interface for the SCD6000 module. The optical interface maintains high
electrical isolation. The diagnostic LEDs provide link and activity indications for each
SFP Ethernet channel. The Ethernet ports can simultaneously support a maximum of
200 TCP/IP connections.
The Ethernet port on the RJ-45 is dedicated to RTV connectivity.
The Ethernet ports support communication with Master station(s) or TCP/IP enabled
IEDs. Through TCP/IP, the Ethernet ports can also connect to the RTV. (Refer to PSS
41S-2M13 for details on the RTV)

6 PSS 41H-8K2, Rev A

 SCD6000 CPU OptoNet Power Supply Ethernet (COPE) Module
Functional Specifications For CPU / SCD6000 CPU OptoNet Ethernet (COE) Module

Functional Specifications For CPU

Processor SPEAr1380 (Dual Core ARM Cortex-A9 at 600 MHz)
Operating System VxWorks®
BIOS Foxboro™ protected mode
Memory System • 256 MB DDR3 SDRAM
• 16 MB flash BIOS
• 64 MB flash file storage
• 256 KB non-volatile RAM
Peripheral Controllers • 16550 type UART integrated with CPU
• DP83620/DP83640 Ethernet controllers
• COM20022 ARCNET controller
Bus Specifications • Foxboro Electrobus
• Watchdog Timer
• 1 second timeout to reset the SCD
Front Panel • Power ON/OFF switch
• Control/Isolate toggle switch
• Control Selector switch
• SEN/RST (Sense/Reset) switch
• RUN and FAIL LED
• Two SFP ports
• One RJ45 Ethernet port
• Two OptoNet Channel ports
• One RS-232/RS-485 Serial port
Serial Ports DB9 male sockets wired per TIA/EIA-574 (DTE)
• RS-232/RS-485 (2 or 4-wire) Link selectable
Enables user configurable communications port
• Supported Protocols
◦ DNP3 (Master and Slave)
◦ IEC 101 (Master)
◦ Modbus (ASCII and RTU, Master and Slave)
◦ HLSI (Generic configurable protocol interface)
◦ GPS Clock (NEMA, Tekron, TrueTime, and others)
Real-Time Clock IBM PC/AT compatible, with 7.5 ppm accuracy. It provides Electrobus
synchronizing and SOE clocks.
Backup Time Real-time clock and non-volatile RAM are maintained during power outage
through a user-replaceable lithium battery. The battery lasts 1 year in storage and
7 years in use.
An LED indicator and a software alarm are provided to indicate that the battery is
low.

PSS 41H-8K2, Rev A 7

SCD6000 CPU OptoNet Power Supply Ethernet (COPE) Module
/ SCD6000 CPU OptoNet Ethernet (COE) Module Functional Specifications For Optonet

Functional Specifications For Optonet

Configuration Dual, counter-rotating ARCNET optical ring arrangement
Interface • TRANSMIT POWER: -12 dBm
• RECEIVE LEVEL: -27 dBm at bit error rate of 10-9
Ports Two ports each containing a Transmit channel and a Receive channel support a
dual ring ARCNET configuration
Maximum Length Between 500 meters
Nodes
Maximum Size of OptoNet • Up to 12 nodes: 5800 meters
Network Ring • For 12 to 63 nodes: [6280 - (40 x Number of nodes)] meters
Optical Cable Glass fiber, multi-mode, 820 nm wavelength, dual 50/125 µm or 62.5/125 µm, ST
connectors
Indicators • 2 LEDs per port indicating Tx and Rx status
• 1 LED for indicating OptoNet communication

8 PSS 41H-8K2, Rev A

 SCD6000 CPU OptoNet Power Supply Ethernet (COPE) Module
Functional Specifications For Ethernet / SCD6000 CPU OptoNet Ethernet (COE) Module

Functional Specifications For Ethernet

SFP Fiber Interface (1) • TRANSMIT POWER: -15 dBm
• RECEIVE LEVEL: -31 dBm at bit error rate of 10-10
• RANGE: 2000 m
Ports • Two SFP ports to support either 100Base-FX or 10/100Base-T
• One RJ-45 port to support 10/100Base-T
Supported Protocols:
• DNP3 (Master and Slave)
• IEC 61850 (Client and Server)
• IEC 60870-5-104 (Slave)
• Modbus TCP (Master and Slave)
• Diagnostic interface
• IED pass-through
Optical Cable Glass fiber, multi-mode, 1310 nm wavelength, dual 50/125 μm or 62.5/125 μm,
LC connector
Indicators 2 LEDs per port indicating link and activity
(1) SFP modules either Copper or Fiber need to be ordered separately. Refer to SFP Modules, page 13.

PSS 41H-8K2, Rev A 9

SCD6000 CPU OptoNet Power Supply Ethernet (COPE) Module
/ SCD6000 CPU OptoNet Ethernet (COE) Module Functional Specifications For Power Supply Board

Functional Specifications For Power Supply Board

Power Requirements • Maximum Power Input: 60 W
• Maximum Power Output: 40 W
Input Voltage Wide range 19.2 V to 148 V DC
Current Limit Shut down at maximum power with auto-recovery
Over-Voltage Protection Crowbar protection on +5 V
Under-Voltage Protection Shut down at low input voltage
Hold-up Time • Exhibits 4 ms hold up time with shorted input power
• Exhibits 10 ms hold up time with open input power
Ripple and Noise • 50 mV peak-to-peak (+5 V)
• 100 mV peak-to-peak (±15 V)
Output • +5 V at 4.5 A
• +15 V at 1.0 A
• –15 V at 0.15 A
Maximum Input Current • 3.3 A at 18 V
• 0.34 A at 164 V
Efficiency > 65% at full load
Isolation 2000 V AC RMS for 1 minute Primary to Chassis and Primary to Secondary
isolation
AT-FS201 from the Allied Telesis is a preferred media converter

10 PSS 41H-8K2, Rev A

 SCD6000 CPU OptoNet Power Supply Ethernet (COPE) Module
Environmental Specifications / SCD6000 CPU OptoNet Ethernet (COE) Module

Environmental Specifications
Operating Storage
Temperature -20°C to +70°C (-4°F to +158°F) -40°C to +85°C (-40°F to +185°F)
Relative Humidity 5 to 95% (non-condensing) 5% to 95% RH (non-condensing)
Altitude -300 m to +2,000 m (-1,000 ft to +6,500 ft)
Vibration 1 g (10 Hz to 150 Hz)
Shock 5 g (18 Pulses for 11ms each)
Bump 10 g (6000 Pulses for 16 ms each)

PSS 41H-8K2, Rev A 11

SCD6000 CPU OptoNet Power Supply Ethernet (COPE) Module
/ SCD6000 CPU OptoNet Ethernet (COE) Module Regulatory Compliance

Regulatory Compliance
ElectroMagnetic Compatibility (EMC)
European EMC Directive 2004/108/EC Meets: EN 61326-1 Immunity requirements for industrial
locations
CISPR 11, Industrial Scientific and Medical (ISM) Meets: Class A Limits
Radio-frequency Equipment - Electromagnetic
Disturbance Characteristics - Limits and Methods of
Measurement
IEC 61000-4-2 ESD Immunity Contact ±6 kV, air ±8 kV
IEC 61000-4-3 Radiated Field Immunity • 10 V/m at 80 to 1000 MHz
• 3 V/m at 80 MHz to 6 GHz
IEC 61000-4-4 Electrical Fast Transient/Burst • 2 kV on I/O and communication lines
Immunity
• 4 kV on DC power lines
IEC 61000-4-5 Surge Immunity • 1 kV on I/O and communication lines
• 2 kV/1 kV on DC power lines
IEC 61000-4-6 Immunity to Conducted Disturbances 10 V (rms) at 150 KHz to 80 MHz on I/O, dc power and
Induced by Radio frequency Fields communication lines
IEC 61000-4-1 6 conducted, common mode • 10 V (rms) to 1 V (rms) 15 Hz to 150 Hz
disturbances Immunity
• 1 V (rms) 150 Hz to 1.5 kHz
• 1 V (rms) to 10 V (rms) 1.5 kHz to 15 KHz
• 10 V (rms) 15 kHz to 150 kHz
IEC 61000-4-17 Ripple on DC Input Power Port 10% of the Nominal Voltage
Immunity
IEC 61000-4-18 Damped Oscillatory wave • 1MHz
• Up to +/-1 KV for common mode
• Up to +/-0.5 KV for differential mode
IEC 61000-4-29 Voltage dips and Short Interruptions Voltage Dips: 30% for 100 ms, 60% for 100 ms, 0% for 50
Immunity ms

Product Safety
This product complies with the following safety standards:
• UL 61010-1 - Safety requirements for electrical equipment for measurement,
control, and laboratory use - Part 1: General requirements - Edition 3
• CSA C22.2 NO. 61010-1 - Safety requirements for Electrical equipment for
measurement, control, and laboratory use
• EN 61010-1:2010 - Safety requirements for electrical equipment for
measurement, control, and laboratory use-Part 1: General requirements

12 PSS 41H-8K2, Rev A

 SCD6000 CPU OptoNet Power Supply Ethernet (COPE) Module
Physical Specifications / SCD6000 CPU OptoNet Ethernet (COE) Module

Physical Specifications
Physical Size
Each of modules is the size of a double Eurocard (233.4 mm x 160 mm board, 261.8
mm x 185 mm x 35.3 mm module). The module requires 35 mm of frame space and
plugs into a backplane (Electrobus) using a DIN 41612 connector.
The dimensions of the SCD6000 CPU Carrier board are 160 mm X 145.48 mm ±0.2
mm and the dimensions of the Power Supply PCB board are 160 mm X 85.7 mm ±0.2
mm.

Ordering Information
Part Number Description
SY-60399001R SCD6000 CPU OptoNet Power Supply Ethernet (COPE)
Module
SY-60399002R SCD6000 CPU OptoNet Ethernet (COE) Module

Optical Patch Cords

Part Number Description
SY-6051034 (1) Optical Cable Assembly Multimode two ST to two ST 5
meters
P0972ZR (1) Optical Cable Assembly Multimode two ST to LC 3 meters
(1) Request longer cables from factory.

SFP Modules
Part Number Description
SY-6034085 10/100Base-T SFP Module
SY-6038038 100 Base-FX SFP Module

PSS 41H-8K2, Rev A 13

Schneider Electric Systems USA, Inc.
38 Neponset Avenue
Foxboro, Massachusetts 02035–2037
United States of America

Global Customer Support: https://pasupport.schneider-electric.com

As standards, specifications, and design change from time to time,

please ask for confirmation of the information given in this publication.

© 2020 Schneider Electric. All rights reserved.

PSS 41H-8K2, Rev A