2018 Civil Seismic Test Plan
2018 Civil Seismic Test Plan
• Buildings
• Non-buildings structures
• Non-structural components, equipment and lifelines
This area of practice is structured into six primary content areas:
I. Seismic Data and Seismic Design Criteria (10%)
II. Seismic Characteristics of Engineered System (15%)
III. Seismic Forces: Building Structures (28%)
IV. Seismic Forces: Non-Building Structures, Components, and Equipment (12%)
V. Seismic Analysis Procedures (25 %)
VI. Seismic Detailing and Construction Quality Control (10%)
(NOTE: As used throughout this test plan, the term applicable code refers to the current adopted
California Building Code.)
BPELSG Civil Engineering: Seismic Principles (CSP) Test Plan-2017
Percentage of
Questions on
the Exam
I. Seismic Data and Seismic Design Criteria
Professional Activities:
1. Practice in accordance to laws, codes and standards governing seismic design.
10%
2. Identify design performance requirements for a project.
3. Determine site-related coefficients.
4. Determine effects of site characteristics on a structure.
5. Determine Seismic Design Category.
Test questions on these professional activities may include one or more of the following:
A. Geologic seismic hazards and geotechnical data that affect design, including
liquefaction and site classification
B. Site-related seismic coefficients
C. Natural period of the structure and the expected period of the seismic ground motion
Professional Activities:
1. Select appropriate seismic force-resisting systems for new or existing structures.
2. Identify effects of structural characteristics on seismic design/performance. 15%
3. Evaluate vulnerability of structures with previous poor seismic performance.
4. Evaluate post-earthquake structural safety.
5. Determine methods for improving seismic performance of existing structures.
Test questions on these professional activities may include one or more of the following:
A. The different structural systems and their design parameters
B. Limitations of different structural systems
C. Requirements for structures with horizontal irregularities (e.g., torsional response, re-
entrant corners, out-of-plane offset)
D. Requirements for structures with vertical irregularities (e.g., vertical discontinuities,
offsets, soft stories)
E. Drift and P-Delta effects
F. Effects of ductility and damping on seismic performance
G. Effects of redundancy on seismic performance
H. Anchorage and stability in existing unreinforced masonry (URM) bearing wall buildings
Professional Activities:
1. Determine structural characteristics required to calculate seismic design forces.
2. Determine seismic design forces for structures. 28%
3. Perform vertical distribution of seismic forces for structures.
4. Determine seismic diaphragm forces.
5. Determine seismic forces for structural elements.
Test questions on these professional activities may include one or more of the following:
A. Mass and stiffness
B. Methods to determine the structure's fundamental period
C. Selection of seismic factors and coefficients required for design
D. Static force procedures and formulas
E. Structural system seismic coefficient application
F. Design base shear
G. Vertical force distribution
H. Design seismic forces on diaphragms
I. Design seismic forces on structural elements
J. Out-of-plane seismic forces on structural elements
K. Design lateral force formulas
IV. Seismic Forces: Non-Building Structures, Components, and
Equipment
Test questions on these professional activities may include one or more of the following:
A. Mass and stiffness
B. Methods to determine the structure's fundamental period
C. Selection of seismic factors and coefficients required for design
D. Static force procedures and formulas
E. Design base shear
F. Application of seismic factors and coefficients for design of non-building structures
Professional Activities:
25%
1. Perform analysis of seismic force resisting systems.
2. Perform the distribution of seismic forces to structural elements.
3. Perform the seismic analysis of diaphragms (e.g., rigid and flexible).
Test questions on these professional activities may include one or more of the following:
A. Applicable load combinations
B. Distribution of internal and external forces
C. Application of deflection and drift requirements
D. Diaphragm force distribution to structural elements (e.g., chord forces, drag forces and
diaphragm shear)
E. Methods used to calculate rigidities of structural elements
F. Distribution of seismic forces based on rigidity
G. Assumptions controlling the analysis for rigid diaphragms
H. Methods to determine centers of rigidity and mass
I. Torsional moment requirements in rigid diaphragms
J. Assumptions controlling the analysis of flexible diaphragms
K. Sub-diaphragm analysis.
VI. Seismic Detailing and Construction Quality Control
Professional Activities:
1. Identify the detailing requirements that are critical for seismic performance (e.g., load 10%
path, wall anchorage, chord and collector).
2. Recognize need for construction quality control of the seismic design aspects of the
project (e.g., testing, special inspection and observation requirements).
Test questions on these professional activities may include one or more of the following:
A. Seismic detailing and inherent seismic performance characteristics for steel
B. Seismic detailing and inherent seismic performance characteristics for concrete