Rockwell Automation Library of Process Objects: Single-Speed Motor (P - Motor)
Rockwell Automation Library of Process Objects: Single-Speed Motor (P - Motor)
IMPORTANT This manual applies to the Rockwell Automation Library of Process Objects version 3.5 or earlier.
For Rockwell Automation Library of Process Objects version 5.0, see
• PROCES-RM200
For Rockwell Automation Library of Process Objects version 4.0 or later, use the following manuals:
• PROCES-RM013 contains logic instructions
• PROCES-RM014 contains display elements
Important User Information
Read this document and the documents listed in the additional resources section about installation, configuration, and
operation of this equipment before you install, configure, operate, or maintain this product. Users are required to
familiarize themselves with installation and wiring instructions in addition to requirements of all applicable codes, laws,
and standards.
Activities including installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are required
to be carried out by suitably trained personnel in accordance with applicable code of practice.
If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be
impaired.
In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from the
use or application of this equipment.
The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and
requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or
liability for actual use based on the examples and diagrams.
No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or
software described in this manual.
Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation,
Inc., is prohibited.
Throughout this manual, when necessary, we use notes to make you aware of safety considerations.
WARNING: Identifies information about practices or circumstances that can cause an explosion in a hazardous environment,
which may lead to personal injury or death, property damage, or economic loss.
ATTENTION: Identifies information about practices or circumstances that can lead to personal injury or death, property
damage, or economic loss. Attentions help you identify a hazard, avoid a hazard, and recognize the consequence.
IMPORTANT Identifies information that is critical for successful application and understanding of the product.
SHOCK HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that dangerous
voltage may be present.
BURN HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that surfaces may
reach dangerous temperatures.
ARC FLASH HAZARD: Labels may be on or inside the equipment, for example, a motor control center, to alert people to
potential Arc Flash. Arc Flash will cause severe injury or death. Wear proper Personal Protective Equipment (PPE). Follow ALL
Regulatory requirements for safe work practices and for Personal Protective Equipment (PPE).
Allen-Bradley, Rockwell Software, Rockwell Automation, RSLogix, Logix5000, FactoryTalk, PlantPAx, and ControlLogix are trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Table of Contents
Preface Software Compatibility and Content Revision. . . . . . . . . . . . . . . . . . . . 5
Additional Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Single-speed Motor (P_Motor) Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Required Files. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Controller File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Visualization Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Controller Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Single-speed Motor Input Structure . . . . . . . . . . . . . . . . . . . . . . . . . 11
Single-speed Motor Output Structure . . . . . . . . . . . . . . . . . . . . . . . 15
Single-speed Motor Local Configuration Tags . . . . . . . . . . . . . . . 19
Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Alarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Simulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Execution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Programming Example. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Display Elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
State Indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Status/Quality Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Mode Indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Alarm Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Maintenance Bypass Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Using Global Elements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Quick Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Faceplate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Operator Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Maintenance Tab. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Engineering Tab. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Diagnostics Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Alarms Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Single-speed Motor Faceplate Help . . . . . . . . . . . . . . . . . . . . . . . . . 48
Notes:
This manual contains new and updated information. Changes throughout this
revision are marked by change bars, as shown to the right of this paragraph.
For the latest compatible software information and to download the Rockwell
Automation® Library of Process Objects, see the Product Compatibility and
Download Center at
http://www.rockwellautomation.com/rockwellautomation/support/pcdc.page.
Additional Resources These documents contain additional information concerning related products
from Rockwell Automation.
Resource Description
PlantPAx® Distributed Control System Selection Guide, Provides information to assist with equipment
publication PROCES-SG001 procurement for your PlantPAx system.
PlantPAx Distributed Control System Reference Manual, Provides characterized recommendations for
publication PROCES-RM001 implementing your PlantPAx system.
Rockwell Automation Library of Process Objects, Provides general considerations for the PlantPAx system
publication PROCES-RM002 library of process objects.
FactoryTalk® View Machine Edition User Manual, Provides details on how to use this software package for
publication VIEWME-UM004 creating an automation application.
FactoryTalk View Site Edition User Manual, Provides details on how to use this software package for
publication VIEWSE-UM006 developing and running human-machine interface (HMI)
applications that can involve multiple users and servers,
distributed over a network.
Logix5000™ Controllers Add-On Instructions Provides information for designing, configuring, and
Programming Manual, publication 1756-PM010 programming Add-On Instructions.
Rockwell Automation Library of Process Objects: Common Details how to monitor an input condition to raise an
Alarm Block (P_Alarm) Reference Manual, alarm. Information includes acknowledging, resetting,
publication SYSLIB-RM002 inhibiting, and disabling an alarm. Generally the P_Alarm
faceplate is accessible from the Alarms tab.
Rockwell Automation Library of Process Objects: Explains how to collect (sum up) the interlock conditions
Interlocks with First Out and Bypass (P_Intlk) Reference that stop or de-energize a running or energized piece of
Manual, publication SYSLIB-RM004 equipment or prevent it from starting or being energized.
Rockwell Automation Library of Process Objects: Common Explains how to choose the Mode (owner) of an
Mode Block (P_Mode) Reference Manual, instruction or control strategy. The Mode instruction is
publication SYSLIB-RM005 usually embedded within other instructions to extend
their functionality. It is possible to use a standalone Mode
instruction to enhance a program where modes are
wanted.
Rockwell Automation Library of Process Objects: Details how to collect permissive conditions to start a
Permissives with Bypass (P_Perm) Reference Manual, piece of equipment.
publication SYSLIB-RM007
Rockwell Automation Library of Process Objects: Restart Explains how to protect a large motor from damage
Inhibit for Large Motor (P_ResInh) Reference Manual, caused by repeated starts.
publication SYSLIB-RM009
Rockwell Automation Library of Process Objects: Run Time Explains how to accumulate the total run time and count
and Starts (P_RunTime) Reference Manual, of starts for a motor or other equipment.
publication SYSLIB-RM010
Rockwell Automation Library of Process Objects: E1 Plus™ Details how to control and monitor a 193-ETN (E1 Plus on
Overload Relay (P_E1PlusE) Reference Manual, EtherNet/IP) overload relay.
publication SYSLIB-RM049A-EN-P
Rockwell Automation Library of Process Objects: Details how to ccontrol and monitor a 193/592-EC1, -EC2,
E3™/E3 Plus™ Overload Relay (EtherNet/IP) (P_E3Ovld) -EC3, or -EC5 (E3 or E3 Plus) overload relay.
Reference Manual, publication SYSLIB-RM050A-EN-P
Rockwell Automation Library of Process Objects: E300™ Details how to controls and monitors a 193-ECM-ETR
Overload Relay (EtherNet/IP) (P_E300Ovld) Reference (E300 on EtherNet/IP) overload relay.
Manual, publication SYSLIB-RM051A-EN-P
Add-On Instruction
Guidelines Use this instruction when you want to control a single-speed (running or
stopped) motor. The motor can use a full voltage starter (FVNR), a soft starter,
or other motor protective equipment, and can optionally provide run feedback.
The P_Motor instruction includes faceplates and graphic symbols for operator
display and manipulation. The instruction provides alarms for several fault
conditions.
Required Files Add-On Instructions are reusable code objects that contain encapsulated logic
that can streamline implementing your system. This logic lets you create your
own instruction set for programming logic as a supplement to the instruction set
provided natively in the ControlLogix® firmware. An Add-On Instruction is
defined once in each controller project, and can be instantiated multiple times in
your application code as needed.
Controller File
The P_Motor_3_5-00_AOI.L5X Add-On Instruction must be imported into
the controller project to be used in the controller configuration. The service
release number (boldfaced) can change as service revisions are created.
Visualization Files
IMPORTANT The visualization file dependencies require Process Library content imports to
occur in a specific order as reflected in the following tables:
• Images
• Global Objects
• Standard Displays
• HMI Tags
• Macros
Images are external graphic files that can be used in displays. They must be
imported for FactoryTalk View to make use of them.
When PNG files are imported, they are renamed by FactoryTalk View with
a .bmp file extension, but retain a .png format.
Table 2 - Visualization Files: Images (.png)
FactoryTalk View SE Software FactoryTalk View ME Software Description
All .png files in the images folder All .png files in the images folder These are the common icons used in the global objects and
standard displays for all Process Objects.
The Global Object files (.ggfx file type) in the following table are Process Library
display elements that are created once and referenced multiple times on multiple
displays in an application. When changes are made to a Global Object, all
instances in the application are automatically updated.
Table 3 - Visualization Files: Global Objects (.ggfx)
FactoryTalk View SE Software FactoryTalk View ME Software Description
(RA-BAS) Common Faceplate Objects (RA-BAS-ME) Common Faceplate Objects Global objects used on process object faceplates.
(RA-BAS) P_Motor Graphics Library (RA-BAS-ME) P_Motor Graphics Library P_Motor global object device symbols used to build
process graphics.
(RA-BAS) Process Alarm Objects (RA-BAS-ME) Process Alarm Objects Global objects used for managing alarms on process
object faceplates.
(RA-BAS) Process Diagnostic Objects (RA-BAS-ME) Process Diagnostic Objects Diagnostic global objects used on process object
faceplates.
(RA-BAS) Process Faceplate Motor Objects (RA-BAS-ME) Process Faceplate Motor Objects Motor global objects used on process object faceplates.
(RA-BAS) Process Help Objects (RA-BAS-ME) Process Help Objects Global objects used for all process objects help displays.
(RA-BAS) Process Interlock Objects (RA-BAS-ME) Process Interlock Objects Global objects used for managing interlocks and
permissives on process object faceplates.
(RA-BAS) Process Mode Objects (RA-BAS-ME) Process Mode Objects Global objects used for managing modes on process
object faceplates.
The Standard Display files (.gfx file type) in the following table are the Process
Library displays that you see at runtime.
Table 4 - Visualization Files: Standard Displays (.gfx)
FactoryTalk View SE Software FactoryTalk View ME Software Description
(RA-BAS) Common-AnalogEdit N/A Faceplate used for analog input data entry. The FactoryTalk
View ME faceplates use the native analog input data entry
so no file is required.
Controller Code This section describes the parameter references for this Add-On Instruction.
Cfg_FailToStartSeverity INT FailToStart.Cfg_Severity 1000 These parameters determine the severity of each alarm. This drives the color and
symbol that are used to indicate alarm status on the faceplate and global object.
Cfg_FailToStopSeverity FailToStop.Cfg_Severity 1000 The following are valid values:
Cfg_IntlkTripSeverity IntlkTrip.Cfg_Severity 500 1…250 = Low
251…500 = Medium
Cfg_IOFaultSeverity IOFault.Cfg_Severity 1000
501…750 = High
751…1000 = Urgent
IMPORTANT: For FactoryTalk View software version 7.0, these severity parameters
drive only the indication on the global object and faceplate. The Alarms and Events
definition of severity drives the color and symbol that is used on the alarm banner
and alarm summary and the value returned by FactoryTalk Alarms and Events
display commands.
Cfg_SimFdbkT DINT 2 Feedback delay in simulation (seconds).
Cfg_FailToStartT DINT 10 Time after start for running feedback before fault (seconds).
Cfg_FailToStopT DINT 10 Time after stop for stopped feedback (= 0) before fault (seconds).
PSet_Owner DINT 0 Program owner request ID (non-zero) or release (zero).
PCmd_Start BOOL 0 When Cfg_PCmdClear is 1:
PCmd_Stop • Set PCmd_Start to 1 to start the motor
• Set PCmd_Stop to 1 to stop the motor
• These parameters are reset automatically
When Cfg_PCmdClear is 0:
• Set PCmd_Start to 1 to start the motor
• Set PCmd_Start to 0 to stop the motor
• PCmd_Stop is not used
• These parameters do not reset automatically
PCmd_Acq BOOL Mode.PCmd_Acq 0 When Cfg_PCmdClear is 1:
• Set PCmd_Acq to 1 to Acquire
PCmd_Rel Mode.PCmd_Rel • Set PCmd_Rel to 1 to Release
• These parameters reset automatically
When Cfg_PCmdClear is 0:
• Set PCmd_Acq to 1 to Acquire
• Set PCmd_Acq to 0 to Release
• PCmd_Rel is not used
• These parameters do not reset automatically
Configuration parameters that are array, string, or structure data types cannot be
configured as parameters for Add-On Instructions. Configuration parameters of
these types appear as local tags to the Add-On Instruction. Local tags can be
configured through the HMI faceplates or in Studio 5000 Logix Designer®
application by opening the Instruction Logic of the Add-On Instruction instance
and then opening the Data Monitor on a local tag. These parameters cannot be
modified by using controller logic or Logix Designer application export/import
functionality.
Operations This section describes the primary operations for Add-On Instructions.
Modes
This instruction uses the following standard modes, which are implemented by
using an embedded P_Mode Add-On Instruction.
Table 10 - Modes
Mode Description
Operator The Operator owns control of the device. Operator commands (OCmd_) and Operator settings
(OSet_) from the HMI are accepted.
Program Program logic owns control of the device. Program commands (PCmd_) and Program settings
(PSet_) are accepted.
Override Priority logic owns control of the device and supersedes Operator and Program control. Override
Inputs (Inp_OvrdCmd and other Inp_OvrdXxxx values) are accepted. If so configured,
bypassable interlocks and permissives are bypassed.
Maintenance Maintenance owns control of the device and supersedes Operator, Program, and Override
control. Operator commands and settings from the HMI are accepted. Bypassable interlocks and
permissives are bypassed, and device timeout checks are not processed.
Hand Hardwired logic or other logic outside the instruction owns control of the device. The instruction
tracks the state of the device for bumpless transfer back to one of the other modes.
No Mode The device is disabled and has no owner because the EnableIn input is false. The main
instruction Logic routine is not being scanned. See Execution section for more information on
EnableInFalse processing.
Alarms
This instruction uses the following alarms, which are implemented by using
embedded P_Alarm and P_Gate Add-On Instructions.
The Fail to Start and Fail to Stop status and alarms have a configurable delay to
allow the run feedback time to align with the commanded output. This delay
provides time for the motor to actually start or stop.
The Fail to Start and I/O fault conditions can be configured to alarm only, or to
de-energize the motor (shed). If one of these conditions stops the motor, a reset is
required to run.
Simulation
You must set the Inp_Sim parameter in the Controller to ‘1’ to enable simulation.
The Simulation or Loopback Test icon is displayed at the bottom left of the
Operator faceplate, indicating the device is in simulation.
The delay (seconds) between a command to Start or Stop and the simulated
started or stopped response is configurable (Cfg_SimFdbkT).
When you have finished in simulation, set the Inp_Sim parameter in the
Controller to ‘0’ to return to normal operation.
Execution
Condition Description
EnableIn False (false rung) Handled the same as if the motor were disabled by
command. The motor outputs are de-energized and the
motor is shown as disabled on the HMI. The mode is
shown as No mode. All alarms are cleared.
Powerup (prescan, first scan) Any commands received before first scan are discarded.
The motor is de-energized and treated as if it were
commanded to stop.
Embedded P_Mode and P_Alarm instructions are
handled in accordance with their standard powerup
procedures. See the Reference Manuals for the P_Mode
and P_Alarm instructions for details.
Postscan (SFC transition) No SFC postscan logic is provided.
Display Elements A display element (global object) is created once and can be referenced multiple
times on multiple displays in an application. When changes are made to the
original (base) object, the instantiated copies (reference objects) are
automatically updated. Use of global objects with tag structures in the
ControlLogix system, aid consistency and save engineering time.
Table 11 - P_Motor Display Elements
Display Element Name Display Element Description
GO_P_Motor_R Motors operate in different positions: right, up, and down.
GO_P_Motor_U
GO_P_Motor_D
GO_P_Motor_Blower_R Blowers operate in different positions: right, left, up, and down.
GO_P_Motor_Blower_L
GO_P_Motor_Blower_U
GO_P_Motor_Blower_D
GO_P_Motor_Inline_R
GO_P_Motor_Inline_L
GO_P_Motor_Inline_D
GO_P_Motor_Pump_L
GO_P_Motor_Pump_U
Status/Quality Maintenance
Indicator Bypass Indicator
Each graphic symbol includes a touch field over it that opens the object’s
faceplate. In addition, there is a tooltip on the graphic symbol that displays the
object’s configured tag and description.
State Indicators
The state indicator text changes and the graphic symbol color changes depending
on the state of the motor.
Status/Quality Indicators
One of these symbols appears on the graphic symbol when the described
condition is true.
Graphic Symbol Description
Invalid configuration.
TIP When the Invalid Configuration indicator appears, you can find what
configuration setting is invalid by following the indicators. Click the graphic
symbol to open the faceplate. The Invalid Configuration indicator appears next
to the appropriate tab at the top of the faceplate to guide you in finding the
configuration error. Once you navigate to the tab, the misconfigured item is
flagged with this indicator or appears in a magenta box.
For the Single Speed Motor Add-On Instruction, the Invalid Configuration
indicator appears under the following conditions:
• The Fail to Start check time or Fail to Stop check time is set to a value less
than zero or greater than 2,147,483 seconds.
• The feedback simulation time is set to a value less than zero or greater than
2,147,483 seconds.
• Alarm Severity is set to a value less than 1 or greater than 1000.
• An alarm minimum on time is set to a value less than zero or greater than
2,147,483 seconds.
TIP When the Not Ready indicator appears, you can find what condition is
preventing operation by following the indicators. Click the graphic symbol to
open the faceplate. The Not Ready indicator appears next to the appropriate
tab at the top of the faceplate to guide you in finding the condition. When you
navigate to the tab, the condition preventing operation is flagged.
For the Single-speed Motor Instruction, the Device Not Ready indicator appears
under the following conditions:
• Device has been disabled by Maintenance.
• There is a configuration error.
• Interlocks are not OK and not bypassed. Non-bypassable interlocks are
not OK.
• Permissives are not OK and not bypassed. Non-bypassable permissives are
not OK.
• Operator State 0 priority command requires reset.
• The motor has a Fail to Start or Fail to Stop that has not been reset.
• There is an I/O Fault, the motor is not being simulated, and shed requires
reset.
Mode Indicators
One of these symbols appears on the right side of the graphic symbol to indicate
the mode of the object instruction.
Transparent Program mode (if the default mode is Program and the current mode is Program, the mode
indicator is transparent).
Override mode
Maintenance mode.
Hand mode
No mode.
TIP The images provided for the Operator and Program default modes are
transparent; therefore, no mode indicators are visible if the device is in its
default mode. This behavior can be changed by replacing the image files for
these mode indicators with images that are not transparent.
Alarm Indicators
One of these symbols appears on the left side of the label to indicate the described
alarm condition and the alarm border and label background change color. The
alarm border and label background blink if acknowledgement of an alarm
condition is required. Once the alarm is acknowledged, the alarm border and
label background remain the color that corresponds to the severity of the alarm.
No symbol No change in color No alarm or alarm inhibit condition, and all alarms
are acknowledged.
This symbol appears to the right of the label to indicate that a maintenance
bypass has been activated.
TIP When the Maintenance Bypass indicator appears, you can find what condition
was bypassed by following the indicators. Click the graphic symbol to open the
faceplate. The Maintenance Bypass indicator appears next to the appropriate
tab at the top of the faceplate to guide you in finding the bypass. Once you
navigate to the tab, the bypassed item is flagged with this indicator.
The global objects for P_Motor can be found in the global object file
(RA-BAS) P_Motor Graphics Library.ggfx. Follow these steps to use a global
object.
1. Copy the global object from the global object file and paste it in the
display file.
2. In the display, right-click the global object and choose Global Object
Parameter Values.
3. In the Value column, type the tag or value as specified in the Description
column.
4. Click OK.
Quick Display The Quick Display screen provides means for operators to perform simple
interactions with the P_Motor instruction instance. From the Quick Display, you
can navigate to the faceplate for full access for operation, maintenance personnel,
and configuration.
Navigate to Full
Faceplate Button
Faceplate The P_Motor faceplate consists of five tabs and each tab consists of one or more
pages.
The title bar of each faceplate contains the value of local configuration tags
Cfg_Tag and Cfg_Desc.
The Operator tab is displayed when the faceplate is initially opened. Click the
appropriate icon at the top of the faceplate to access a specific tab.
Maintenance Diagnostics Exit
The faceplate provides the means for operators, maintenance workers, engineers,
and others to interact with the P_Motor instruction instance, including viewing
its status and values and manipulating it through its commands and settings.
When a given input is restricted via FactoryTalk View security, the required user
security code letter is shown in the tables that follow.
Operator Tab
The Faceplate initially opens to the Operator (‘Home’) tab. From here, an
operator can monitor the device status and manually operate the device when it is
in Operator mode.
The Operator tab has buttons to start and stop the motor when it is in the proper
mode and shows the following information:
• Current mode (Program, Operator, Override, Maintenance, or Hand)
• Requested mode indicator (appears only if Operator or Program mode has
been superseded by another mode)
• Motor state (stopping, stopped, starting, or running)
• Interlock and permissive states
• Input Source and Quality indicator (See 'SrcQ' in the Output parameters
table on page 16 for details).
IMPORTANT This indicator is not displayed if 'Motor has Run Feedback' on page 1 of
the Engineering tab is not checked. (See Engineering Tab Page 1 on
page 40.)
Mode Indicator
Permissive Indicator/
Restart Inhibit Navigation Button
Navigation Button
Runtime
Navigation
Button
Input Source and
Quality Indicator
Input Source and
Quality Icon
The following table shows the functions that are included on the Operator tab.
Table 13 - Operator Tab Descriptions
Function Action Security
Click to lock in Operator mode. Function locks the mode in Manual Device
Operator mode, preventing the program from taking control. Operation (Code B)
The Operator tab also has a button to open the runtime faceplate if the motor is
configured to use the P_RunTime object (Cfg_HasRunTime = 1). When the
object is not configured to have an associated P_RunTime instruction, the
runtime button is not displayed.
The Operator tab also has a button to open the Restart Inhibit faceplate if the
motor is configured to use the P_ResInh object (Cfg_HasResInh = 1). When the
object is not configured to have an associated P_ResInh instruction, the Restart
Inhibit button is not displayed.
The Operator tab also has a button to open an Overload faceplate if the motor is
configured to have an associated Overload object (Cfg_HasOvld = 1). When the
object is not configured to have an associated Overload object, the Overload
button is not displayed.
The following figure shows the Operator tab when it is not configured to have
Permissives or Interlocks. It also does not have the P_ResInh, P_RunTime, or
P_Ovld associated instructions.
Non-bypassed conditions OK
All conditions OK
Alarm indicators appear on the Operator tab when the corresponding alarm
occurs.
The following table shows the alarm status symbols used on the Operator tab.
Table 15 - Operator Tab Alarm Status
Graphic Symbol Alarm Status
In Alarm (Active Alarm)
Maintenance Tab
Maintenance personnel use the information and controls on the Maintenance tab
to adjust device parameters, troubleshoot and temporarily work around device
problems, and disable the device for routine maintenance.
Engineering Tab
On page 1 of the Engineering tab, you can configure the description, label, and
tag for the device.
The following table lists the functions on page 1 of the Engineering tab.
This display lets you select the default mode for the object by selecting the
appropriate mode.
IMPORTANT If no mode is being requested, changing the default mode changes the mode
of the instruction.
You must have FactoryTalk View security code E to select the default mode on
this display.
The following table shows the functions on page 2 of the Engineering tab.
Diagnostics Tab
The Diagnostics tab displays possible reasons for the device not being ready.
The preceding image indicates that the device is not ready because of an I/O fault
shed condition, which requires reset.
Alarms Tab
The Alarms Tab shows all available alarms for the device and their current status.
From here, alarms can be acknowledged and reset. Click an alarm name to open
the alarm detail faceplate for that alarm, where the alarm can be shelved by the
operator, disabled by maintenance personnel, or configured by engineering.
Acknowledge Alarm
Command Button
Alarm Names
Alarm
Severity
Indicators
Reset and
Acknowledge All
Alarms Command
Button
IMPORTANT The 'Failed to Start' and 'Failed to Stop' alarms are not available if 'Motor has
Run Feedback' on page 1 of the Engineering tab is not checked.
(See Engineering Tab Page 1 on page 40.)
Click an alarm name to open the P_Alarm faceplate for that alarm. From the
P_Alarm faceplate, you can configure and perform additional operations on
the alarm.
If an alarm is active, the panel behind the alarm changes color to match the
severity of the alarm. The color of the bell icon at the top of the faceplate shows
the severity of the highest active alarm, and the icon blinks if any alarm is
unacknowledged or requires reset.
When the Reset and Acknowledge All Alarms button is enabled, the panel
behind the alarm blinks, indicating the alarm requires acknowledgement or reset.
The Alarm Acknowledge button is enabled if the alarm requires
acknowledgment. Click the button with the check mark to acknowledge the
alarm.
Notes:
In addition, we offer multiple support programs for installation, configuration, and troubleshooting. For more
information, contact your local distributor or Rockwell Automation representative, or visit
http://www.rockwellautomation.com/services/online-phone.
Installation Assistance
If you experience a problem within the first 24 hours of installation, review the information that is contained in this
manual. You can contact Customer Support for initial help in getting your product up and running.
United States or Canada 1.440.646.3434
Outside United States or Canada Use the Worldwide Locator at http://www.rockwellautomation.com/rockwellautomation/support/overview.page, or contact your local
Rockwell Automation representative.
Rockwell Automation tests all of its products to help ensure that they are fully operational when shipped from the
manufacturing facility. However, if your product is not functioning and needs to be returned, follow these procedures.
United States Contact your distributor. You must provide a Customer Support case number (call the phone number above to obtain one) to your
distributor to complete the return process.
Outside United States Please contact your local Rockwell Automation representative for the return procedure.
Documentation Feedback
Your comments will help us serve your documentation needs better. If you have any suggestions on how to improve this
document, complete this form, publication RA-DU002, available at http://www.rockwellautomation.com/literature/.
Rockwell Otomasyon Ticaret A.Ş., Kar Plaza İş Merkezi E Blok Kat:6 34752 İçerenköy, İstanbul, Tel: +90 (216) 5698400