Professional Documents
Culture Documents
GR00007800 23a PDF
GR00007800 23a PDF
GROUP 23A
CVT
CONTENTS
WARNING
• Improper service or maintenance of any component of the SRS, or any SRS-related component, can lead to
personal injury or death to service personnel (from inadvertent firing of the air bag) or to the driver and
passenger (from rendering the SRS inoperative).
• Service or maintenance of any SRS component or SRS-related component must be performed only at an
authorized MITSUBISHI dealer.
• MITSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP 52B - Supplemental
Restraint System (SRS) before beginning any service or maintenance of any component of the SRS or any
SRS-related component.
NOTE
The SRS includes the following components: SRS air bag control unit, SRS warning light, front impact sensors, air bag module,
side-airbag module, curtain air bag module, side impact sensors, seat belt pre-tensioners, clock spring, and interconnecting
wiring. Other SRS-related components (that may have to be removed/installed in connection with SRS service or maintenance)
are indicated in the table of contents by an asterisk (*).
23A-2
TSB Revision
23A-4 CVT
GENERAL INFORMATION
TRANSAXLE CONFIGURATION
DRAWING
.
Reverse brake
Forward clutch COMPONENTS AND FUNCTIONS
Component Function
Primary pulley
Forward clutch Operates when moving forward
and rotates the primary pulley
normally.
Reverse brake Operates when moving
backward and rotates the
primary pulley reversely via the
planetary gear.
Secondary
pulley Primary pulley Transfers the rotation from the
Steel belt planetary gear to the secondary
pulley via the steel belt.
Steel belt Transfers the rotation from the
AC610350AB
primary pulley to the secondary
pulley.
Secondary pulley Transfers the rotation from the
primary pulley to the differential.
TSB Revision
CVT
GENERAL INFORMATION
23A-5
SECTIONAL VIEW
5 4 3 2
7 6
1
8
23
10 22
11 21
12
20
19
18
17
13 14
16
15
AC505738AB
TSB Revision
23A-6 GENERAL INFORMATION
CVT
INVECS-III CONTROL
INVECS-III has been newly developed based on
INVECS-II utilizing continuous variable characteris-
tics of CVT.
TCM
AC504721AB
To select the pulley ratio which can provide the driv- vehicle speed, accelerator angle. Then, it outputs the
ing force corresponding to the driver's intention and command to the stepper motor, controls in/out flow of
vehicle conditions, TCM selects the optimal pulley the line pressure to/from the primary pulley, positions
ratio and determines the shift strategy to obtain it by the movable pulley of the primary pulley, and controls
detecting the vehicle driving conditions such as the the gear ratio.
.
TSB Revision
CVT
GENERAL INFORMATION
23A-7
ENGINE BRAKE FEATURE ON THE
DESCENDING SLOPE
Pulley ratio is controlled to obtain the engine brake
suitable for the driver’s feelings.
.
HIGH
Pulley ratio
LOW
Often use brake
100%
Throttle opening
Often use accelerator
0%
Acceleration
TSB Revision
23A-8 CVT
GENERAL INFORMATION
40%
20%
Target primary 0%
revolution speed
When driving in a
normal condition
Vehicle speed
AC610384 AB
Target primary
revolution speed
lower limit value
Driving on the
ascending slope
or driving fast
Target primary
revolution speed
Cruising on
flat road
TSB Revision
CVT
GENERAL INFORMATION
23A-9
SYSTEM CONSTRUCTION DIAGRAM
Transmission range
switch
ABS-ECU
Shift switch assembly
AC610161AD
RATIO PATTERN
<D RANGE>
Engine speed (r/min)
7,000
Low
Throttle opening 100%
6,000
5,000
Throttle opening 75%
4,000
OD
Throttle opening 50%
3,000
Throttle opening 0%
1,000
TSB Revision
23A-10 CVT
GENERAL INFORMATION
<SPORT MODE>
Engine speed (r/min)
7,000
Low
6,000
1st
5,000
4,000
4th OD
3,000
2,000
1,000
TSB Revision
CVT
GENERAL INFORMATION
23A-11
DIRECT CONTROL (TORQUE CONVERTER CLUTCH CONTROL)
Engine speed (r/min)
7,000
Low
6,000
5,000
4,000
Disengaged
Lock-up OD
3,000
2,000
1,000
Partial lock-up zone
TSB Revision
23A-12 CVT
SERVICE SPECIFICATIONS
SERVICE SPECIFICATIONS
M1231200300557
LUBRICANT
M1231200400617
TSB Revision
CVT
DIAGNOSIS
23A-13
DIAGNOSIS
DIAGNOSTIC TROUBLESHOOTING FLOW
M1231213500249
NG
Check the transmission fluid. Replace or replenish the
transmission fluid.
OK
Verify complaint.
Communication with the scan tool
MB991958 (M.U.T.-III sub assembly)
not possible
Communication with the scan tool
Read the diagnostic trouble code.
MB991958 (M.U.T.-III sub assembly)
not possible in Symptom Chart.
Diagnostic trouble code No diagnostic trouble code
displayed. displayed.
Erase the diagnostic trouble code. Check symptom.
AC807916
TSB Revision
23A-14 CVT
DIAGNOSIS
2. Verify that the condition described by the 6. If there is a DTC, record the number of the code,
customer exists. then erase the code from memory using scan tool.
3. Check the vehicle for any CVT Diagnostic Trouble 7. Reconfirm the symptom with a Road Test.
Codes (DTCs). 8. If a DTC is set again, go to the Inspection Chart
4. If you cannot verify the condition and there are no for Diagnostic Trouble Codes.
DTCs, the malfunction is intermittent. For 9. If a DTC is not set again, the malfunction is
information on how to cope with intermittent intermittent. For information on how to cope with
malfunctions, refer to GROUP 00, How to Use intermittent malfunctions, refer to GROUP 00,
Troubleshooting/Inspection Service Points − How How to Use Troubleshooting/Inspection Service
to Cope with Intermittent Malfunction P.00-15. Points − How to Cope with Intermittent
5. If you can verify the condition but there are no Malfunction P.00-15.
DTCs, or the system cannot communicate with 10.After repairs are completed, conduct a Road Test
scan tool, refer to the Symptom Chart P.23A-28. duplicating the complaint conditions to confirm the
malfunction has been eliminated.
DIAGNOSTIC FUNCTION
M1231219000316
WARNING INDICATOR
When any malfunction occurs in the items related to the CVT
(A)
system, which are described below, the symbol (A) continues
being displayed in the information screen in the multi informa-
SERVICE
REQUIRED
tion display.
(B)
Check if the diagnostic trouble code is set when the symbol (A)
continues being displayed in the information screen in the multi
information display.
SLOW DOWN
NOTE: When the symbol (B) is displayed in the information
screen in the multi information display, the transmission fluid
AC510377 AB temperature is high. (Symbol (B) is turned on when the fluid
temperature is approximately 140°C (284°F) or higher and
turned off automatically when the fluid temperature drops
below approximately 137°C (279°F).)
TSB Revision
CVT
DIAGNOSIS
23A-15
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
Data link connector necting or disconnecting scan tool MB991958.
1. Ensure that the ignition switch is at the "LOCK" (OFF)
position.
2. Start up the personal computer.
3. Connect special tool MB991827 to special tool MB991824
and the personal computer.
4. Connect special tool MB991910 to special tool MB991824.
MB991910
5. Connect special tool MB991910 to the data link connector.
MB991824 6. Turn the power switch of special tool MB991824 to the "ON"
position.
NOTE: When special tool MB991824 is energized, special
tool MB991824 indicator light will be illuminated in a green
color.
7. Start the M.U.T.-III system on the personal computer.
NOTE: Disconnecting scan tool MB991958 is the reverse of the
MB991827
connecting sequence, making sure that the ignition switch is at
AC608435 AB
the "LOCK" (OFF) position.
MB991827 AC608435 AB
TSB Revision
23A-16 CVT
DIAGNOSIS
MB991827 AC608435 AB
TSB Revision
CVT
DIAGNOSIS
23A-17
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
Data link connector necting or disconnecting scan tool MB991958.
1. Connect scan tool MB991958 to the data link connector.
2. Turn the ignition switch to the "ON" position.
3. Select "CAN bus diagnosis" from the start-up screen.
4. When the vehicle information is displayed, confirm that it
matches the vehicle whose CAN bus lines will be
diagnosed.
MB991910
• If they match, go to step 8.
MB991824 • If not, go to step 5.
5. Select the "view vehicle information" button.
6. Enter the vehicle information and select the "OK" button.
7. When the vehicle information is displayed, confirm again
that it matches the vehicle whose CAN bus lines will be
diagnosed.
• If they match, go to step 8.
• If not, go to step 5.
MB991827 AC608435 AB
8. Select the "OK" button.
9. When the optional equipment screen is displayed, choose
the one which the vehicle is fitted with, and then select the
"OK" button.
HOW TO INITIALIZE CVT LEARNED VALUE
M1231202400345
PURPOSE
then move the selector lever to the "R" range.
After the CVT assembly, engine assembly, and valve
body assembly are replaced, their learned value 3. Depress the accelerator pedal while depressing
must be initialized. The initialization procedure is as the brake pedal. (Engine is not running.) Using
below. the scan tool, execute the clear DTC function for
the CVT ECU (even if no codes are set).
NOTE: Performing initialization of the learned value
.
INITIALIZATION PROCEDURE
will also erase the diagnostic trouble code.
1. Move the selector lever to the "P" range and turn
the ignition switch to the "LOCK" (OFF) position.
Then, connect the scan tool to the data link
connector.
LEARNING PROCEDURE FOR CVT HYDRAULIC CONTROL
M1231225500451
PURPOSE
After initialization, the TCM does not have any
learned value. This may degrade the shifting opera-
tion quality. The learning procedure is described
below.
TSB Revision
23A-18 CVT
DIAGNOSIS
LEARNING PROCEDURES
Steps Item Contents
1 Learning procedure for engine idling Refer to GROUP 00, Precautions before Service -
Learning Procedures for Idling in MFI Engine P.00-43.
2 Fluid cooling Park the vehicle in a cooler place, stop the engine, and
leave the vehicle until the fluid temperature is lowered to
the ambient temperature.
3 Learning in (1) Fluid temperature Use scan tool MB991958 to measure the fluid
cold engine measurement temperature. (Check that the fluid temperature is the
condition same as the ambient temperature.)
(2) Line pressure and shift Let the engine idle for 20 seconds in the "D" range.
control learning
(3) Direct control learning Run the vehicle at 40 − 50 km/h (25 − 31 mph) for 5
seconds in the "D" range with steady operation.
4 Learning in (1) Fluid temperature CAUTION
hot engine adjustment When the CVT fluid temperature does not increase to
condition 80°C (176°F) in cold region, raise the fluid
temperature to a maximum extent.
Raise the fluid temperature to 80°C (176°F).
(2) Direct control learning The same procedure as for "Learning in cold engine
condition"
FAIL-SAFE FUNCTION/BACKUP FUNCTION
M1231208300078
If abnormality occurs in signals from various sensors,
switches, or solenoids, this function allows control-
ling them with the minimum adverse effect to the
driving performance. The following shows the
fail-safe controls when an abnormal signal is input to
TCM from each sensor.
Malfunctioning Item Control Default During Malfunction
Secondary pulley speed sensor Performs the shift control depending on the accelerator angle. Also,
prohibits the sport mode and controls as the D range.
Primary pulley speed sensor Performs the shift control depending on the accelerator angle and
secondary pulley rotation (vehicle speed). Also, prohibits the sport
mode and controls as the D range.
Transmission range switch Controls as the D range.
Transmission fluid temperature Controls using the fixed value for the fail-safe function.
sensor
Secondary pressure sensor Stops the secondary pressure feedback control and controls the line
pressure using the fixed value for the fail-safe function. Also,
suppresses the engine torque.
Line pressure solenoid valve Switches the line pressure solenoid valve OFF to achieve the
maximum line pressure.
Secondary pressure solenoid valve Switches the secondary pressure solenoid valve OFF to achieve the
maximum secondary pressure.
Lock-up solenoid valve Switches the lock-up solenoid valve OFF to release lock-up.
Stepper motor Switches all the coils A to D of the stepper motor OFF to retain the
gear ratio just before the abnormality occurs.
TSB Revision
CVT
DIAGNOSIS
23A-19
Malfunctioning Item Control Default During Malfunction
Lock-up/select switching solenoid Switches the lock-up/select switching solenoid valve OFF to release
valve lock-up.
Back-up power supply If the control memory back-up power supply from the battery is not
supplied to TCM, limits the engine torque to protect the transaxle
main body. After the normal power is supplied, turning the key switch
from "LOCK" (OFF) to "ON" once resumes the normal status.
Paddle shift switch <Vehicles with Prohibits the paddle shift operation.
paddle shift>
Shift switch assembly Prohibits the sport mode operation.
ROAD TEST
M1231207800553
Steps Conditions for Test/Operation Judgment standard Check item Diagnostic Reference for
test/operation trouble checking
code procedure in
number case of error
1 Ignition switch: Ignition switch Data list No.6 ECU power − Communic
LOCK (OFF) (1) ON (1) Battery voltage supply ation with
the scan
tool is not
possible.
TSB Revision
23A-20 CVT
DIAGNOSIS
Steps Conditions for Test/Operation Judgment standard Check item Diagnostic Reference for
test/operation trouble checking
code procedure in
number case of error
2 Ignition switch: Transmission range Data list No.49 Transmissio P0705 Malfunction
ON (1) P (1) P (2) R (3) N n range of
Engine: (2) R (4) D switch transmissio
Stopped (3) N n range
(4) D switch
Transmission range Data list No.42
(1) P (1) ON (2) OFF
(2) R (3) OFF (4) OFF
(3) N (5) OFF
(4) D Data list No.43
(5) Sport mode (1) OFF (2) ON
(3) OFF (4) OFF
(5) OFF
Data list No.44
(1) OFF (2) OFF
(3) ON (4) OFF
(5) OFF
Data list No.45
(1) OFF (2) OFF
(3) OFF (4) ON
(5) OFF
Data list No.46
(1) OFF (2) OFF
(3) OFF (4) OFF
(5) OFF
Data list No.47
(1) OFF (2) OFF
(3) OFF (4) OFF
(5) ON
Paddle shift lever Data list No.54 Paddle shift P0815, Malfunction
position <Vehicles with (1) ON switch P0816 of paddle
paddle shift> (2) OFF shift switch
(1) Upshift (left side assembly
operation of the lever)
and hold
(2) Release the lever.
Paddle shift lever Data list No.55
position <Vehicles with (1) ON
paddle shift> (2) OFF
(1) Downshift (right
side operation of the
lever) and hold
(2) Release the lever.
TSB Revision
CVT
DIAGNOSIS
23A-21
Steps Conditions for Test/Operation Judgment standard Check item Diagnostic Reference for
test/operation trouble checking
code procedure in
number case of error
2 Ignition switch: Transmission range Data list No.51 Select P0826 Malfunction
ON (1) D (1) OFF switch of shift
Engine: (2) Select sport mode (2) ON switch
Stopped (3) Upshift and hold (3) ON assembly
(4) Downshift and hold (4) ON
Data list No.52 Shift switch
(1) OFF (UP)
(2) OFF
(3) ON
(4) OFF
Data list No.53 Shift switch
(1) OFF (DOWN)
(2) OFF
(3) OFF
(4) ON
Transmission range Data list No.36 Lockup/sele P1740 Malfunction
(1) P, N (1) ON ct switching of
(2) 5 or more seconds (2) OFF solenoid lockup/sele
have passed after the Data list No.37 valve ct switching
selector lever has (1) ON solenoid
been moved to the R (2) OFF valve
or D position.
3 Ignition switch: Accelerator pedal Data list No.13 APS − −
ON (1) Fully closed (1) 0%
Engine: (2) Depressed (2) Gradually
Stopped (3) Fully opened increases from (1).
Transmission (3) 100%
range: P Brake pedal Data list No.50 Stoplight P0703 Malfunction
(1) Depressed (1) ON switch of stoplight
(2) Released (2) OFF switch
4 Engine Drive the vehicle for Data list No.5 Transmissio P0712, Malfunction
warming up 15 minutes or more to Voltage drops n fluid P0713 of the
raise the transmission gradually. temperature transmissio
fluid temperature to 45 Data list No.20 sensor n fluid
− 100°C (113 − COUNT increases as temperatur
212°F). the fluid temperature e sensor
increases.
5 Engine: Idling • Transmission Data list No.9 Engine P0725 Abnormal
range: P 600 to 800 r/min speed engine
• Accelerator pedal speed
fully closed
TSB Revision
23A-22 CVT
DIAGNOSIS
Steps Conditions for Test/Operation Judgment standard Check item Diagnostic Reference for
test/operation trouble checking
code procedure in
number case of error
5 Transmission range: P Should be no Malfunction - Shock is
→R→N→D abnormal shift shocks when experience
Time delay when starting d during N
engaging should be to D and/or
within 2 seconds N to R
shifting
operation
- Vehicle
creeps in
the N range
Transmission range: N Data list No.4 Secondary P0840 Malfunction
0.5 − 3.0 V pressure of
sensor secondary
pressure
sensor
Data list No.32 Line P0745 Malfunction
0.45 − 0.75 A pressure of line
solenoid pressure
valve solenoid
valve
Data list No.34 Secondary P0778 Malfunction
0.45 − 0.75 V pressure of
solenoid secondary
valve pressure
solenoid
valve
6 Transmission Running Data list No.1 Primary P0715 Malfunction
range: D Nearly the same as speed of primary
the tachometer sensor speed
display sensor
Data list No.2 Secondary P0720 Malfunction
Nearly the same as speed of
the tachometer sensor secondary
display speed
sensor
Data list Nos.38, 39, Stepper P1777, Malfunction
40, 41 motor P1778 of stepper
ON/OFF switches motor
alternately.
Stop the vehicle, and Data list No.30 Lockup P0740, Malfunction
then accelerate to 60 0 − 0.7 A solenoid P0741 of lockup
km/h (37 mph) on a valve solenoid
level road. valve
TSB Revision
CVT
DIAGNOSIS
23A-23
Steps Conditions for Test/Operation Judgment standard Check item Diagnostic Reference for
test/operation trouble checking
code procedure in
number case of error
7 Transmission Transmission range Data list No.60 Poor − Poor
range: Sport (1) Stopped while (1) 1st acceleration acceleratio
mode idling the engine. (2) 2nd or n or
(2) Driving at a (3) 3rd incomplete incomplete
constant speed of 30 (4) 4th shifting shifting
km/h (19 mph) in 2nd (5) 5th operation operation
gear (6) 6th
(3) Driving at a
constant speed of 35
km/h (22 mph) in 3rd
gear
(4) Driving at a
constant speed of 40
km/h (25 mph) in 4th
gear
(5) Driving at a
constant speed of 50
km/h (31 mph) in 5th
gear
(6) Driving at a
constant speed of 60
km/h (37 mph) in 6th
gear
TSB Revision
23A-24 CVT
DIAGNOSIS
CAUTION
• Do not maintain the WOT condition for 5 seconds or
longer.
• When continuing the stall test, make sure that the fluid
temperature does not exceed 80°C (176°F). If the trans-
mission fluid temperature exceeds 80°C (176°F), run
the engine at around 1,000 r/min for 1 minute or longer
to lower the transmission fluid temperature to 80°C
(176°F) or less.
5. Move the selector lever to the "D" range and fully depress
the accelerator pedal. Quickly read the maximum engine
speed at this time.
Standard value − Stall speed: 2,400 − 2,900 r/min
6. Move the selector lever to the "R" range, and then repeat
the previous step.
Standard value − Stall speed: 2,400 − 2,900 r/min
CAUTION
The transmission fluid temperature should be between 70
− 80°C (158 − 176°F) during the test.
1. Check the transmission fluid level and temperature. Check
engine coolant temperature.
• Transmission fluid level: "HOT" mark on the dipstick
• Transmission fluid temperature: 70 − 80°C (158 − 176°F)
• Engine coolant temperature: 80 − 100°C (176 − 212°F)
2. Raise the vehicle so that the wheels are free to turn.
TSB Revision
CVT
DIAGNOSIS
23A-25
3. Connect the special tools (3.0 MPa (427 psi) oil pressure
PRI
gauge [MD998330] and joint [MD998331, MB992127]) to
DR each pressure discharge port.
PL NOTE: .
DR: Torque converter output pressure port
PRI: Primary pressure port
PL: Line pressure port
FWD: Forward clutch pressure port
FWD REV: Reverse brake pressure port
AC507202 AB 4. Restart the engine.
5. Check that there are no leaks around the special tool port
adapters.
REV
WARNING
For safety, operators must not stand in front of and at
the rear of the vehicle during this test.
6. Measure the hydraulic pressure at each port under the
conditions given in the standard hydraulic pressure table,
and check that the measured values are within the standard
value ranges.
AC507203 AB 7. If the pressure is not within the standard value, stop the
engine and refer to the hydraulic pressure test diagnosis
table.
8. Remove the O-ring from the port plug and replace it.
9. Remove the special tool, and install the plugs to the
hydraulic pressure ports.
10.Start the engine and check that there are no leaks around
the plugs.
Standard hydraulic pressure table
Measuring conditions Standard hydraulic pressure MPa (psi)
Transmission Engine Forward clutch Reverse brake Primary Line pressure Torque
range speed pressure pressure pressure [Pressure at converter
[Pressure at [Pressure at [Pressure at PL] [Pressure at
FWD] REV] PRI] DR]
P Idling 0 (0) 0 (0) 0.1 − 1.5 (15 − 0.5 − 1.5 (73 − 0.1 − 1.0 (15 −
218) 218) 145)
R 0 (0) 0.5 − 1.0 (73 − 0.1 − 1.5 (15 − 0.5 − 1.5 (73 − 0.1 − 1.0 (15 −
145) 218) 218) 145)
N 0 (0) 0 (0) 0.1 − 1.5 (15 − 0.5 − 1.5 (73 − 0.1 − 1.0 (15 −
218) 218) 145)
D 0.5 − 1.0 (73 − 0 (0) 0.1 − 1.5 (15 − 0.5 − 1.5 (73 − 0.1 − 1.0 (15 −
145) 218) 218) 145)
TSB Revision
23A-26 CVT
DIAGNOSIS
AC509098AB
TSB Revision
CVT
DIAGNOSIS
23A-27
DIAGNOSTIC TROUBLE CODE CHART
M1231207900765
CAUTION
During diagnosis, a diagnostic trouble code
associated with other system may be set when
the ignition switch is turned on with connector(s)
disconnected. On completion, confirm all sys-
tems for diagnostic trouble code(s). If diagnostic
trouble code(s) are set, erase them all.
Diagnostic Diagnostic item Reference
trouble code No. page
P0703 Malfunction of stoplight switch P.23A-29
P0705 Malfunction of transmission range switch P.23A-33
P0711 Malfunction of the transmission fluid temperature sensor P.23A-33
P0712 Malfunction of the transmission fluid temperature sensor (short) P.23A-41
P0713 Malfunction of the transmission fluid temperature sensor (open)
P0715 Malfunction of primary pulley speed sensor P.23A-46
P0720 Malfunction of secondary pulley speed sensor P.23A-51
P0725 Malfunction of engine speed P.23A-55
P0740 Malfunction of lockup solenoid valve P.23A-58
P0741 Abnormality in lockup function P.23A-61
P0745 Malfunction of line pressure solenoid valve P.23A-63
P0746 Abnormality in hydraulic control system function P.23A-66
P0776 Abnormality in secondary pressure solenoid valve function P.23A-69
P0778 Malfunction of secondary pressure solenoid valve P.23A-70
P0815 Malfunction of paddle shift up switch <Vehicles with paddle shift> P.23A-73
P0816 Malfunction of paddle shift down switch <Vehicles with paddle shift> P.23A-75
P0826 Malfunction of sport mode shift switch P.23A-76
P0840 Malfunction of secondary pressure sensor P.23A-79
P0841 Abnormality in line pressure sensor function P.23A-82
P0868 Secondary pressure drop P.23A-84
P0882 Malfunction of system power supply (Low) P.23A-87
P0883 Malfunction of system power supply (High)
P1637 Malfunction of memory backup P.23A-89
P1706 Malfunction of throttle signal P.23A-91
P1710 Malfunction of vehicle speed signal P.23A-93
P1723 Abnormality in speed sensor system function P.23A-95
P1740 Malfunction of lockup/select switching solenoid valve P.23A-98
P1745 Monitoring of percentage change in gear ratio P.23A-101
P1773 Malfunction of ABS P.23A-103
P1777 Malfunction of stepper motor P.23A-103
TSB Revision
23A-28 CVT
DIAGNOSIS
CAUTION
During diagnosis, a diagnostic trouble code
associated with other system may be set when
the ignition switch is turned on with connector(s)
disconnected. On completion, confirm all sys-
tems for diagnostic trouble code(s). If diagnostic
trouble code(s) are set, erase them all.
Trouble symptom Inspection Reference
procedure page
number
TCM cannot communicate with scan tool. 1 P.23A-115
Vehicle creeps in the N range. 2 P.23A-117
Shock is experienced during N to D and/or N to R shifting operation. 3 P.23A-118
Poor acceleration or incomplete shifting operation. 4 P.23A-118
Cannot be changed in sport mode. 5 P.23A-119
Cannot be changed with paddle shift. <Vehicles with paddle shift> 6 P.23A-122
The fluid temperature warning lamp illuminates too frequently. 7 P.23A-124
TSB Revision
CVT
DIAGNOSIS
23A-29
DIAGNOSTIC TROUBLE CODE PROCEDURES
FUSIBLE
LINK 34
ETACS-ECU
STOPLIGHT
SWITCH
STOPLIGHT
RELAY
C-403
C-29 (B)
C-25
C-410
ACA03038 BR ACA03053BC
. .
DIAGNOSTIC FUNCTION
TCM detects malfunction using the stoplight switch
signal sent from the ETACS-ECU.
TSB Revision
23A-30 CVT
DIAGNOSIS
START
Yes
Yes
No
Continuous failure for 10 sec.
Yes
Fail counter up
Yes
No
Fail counter 2 times.
Yes
Malfunction Good
END
AC802601
TSB Revision
CVT
DIAGNOSIS
23A-31
DTC SET CONDITIONS OBD-II DRIVE CYCLE PATTERN
Drive the vehicle for 10 seconds or more at 30 km/h
Check Conditions
(19 mph) or higher (2 drive cycle)
• Vehicle speed: 30 km/h (19 mph) or more.
• Voltage of battery: 9 volts or more. .
DIAGNOSIS
TSB Revision
23A-32 CVT
DIAGNOSIS
TSB Revision
CVT
DIAGNOSIS
23A-33
IGNITION
SWITCH (IG1)
ETACS-ECU
IG1
RELAY
TRANSMISSION
RANGE
SWITCH
TRANSAXLE
CONTROL
MODULE
ACA03448
TSB Revision
23A-34 CVT
DIAGNOSIS
A-16 A-17
ACA03039AG ACA03038 BU
C-417
B-122 (B)
C-412 (BR)
ACA03088AC ACA03053BE
Connector: C-28
ACA03038 BT
DIAGNOSTIC FUNCTION
TCM monitors the signal from the transmission range .
TSB Revision
CVT
DIAGNOSIS
23A-35
• Secondary pulley speed sensor
.
START
No
Multiple signal
Yes
No
Continuous for 2 sec
Yes
No
No signal
Yes
No
Continuous for 5 sec
Yes
Yes
Malfunction Good
END
AC710006
Judgment Criteria
.
TSB Revision
23A-36 CVT
DIAGNOSIS
DIAGNOSIS
TSB Revision
CVT
DIAGNOSIS
23A-37
TSB Revision
23A-38 CVT
DIAGNOSIS
MONITOR EXECUTION
.
DIAGNOSTIC FUNCTION
TCM conducts fault detection by monitoring the ter- • Transmission range:D
minal voltage of the transmission fluid temperature • Vehicle speed : 10 km (6.2 mph) or more
sensor. • Throttle valve opening : 1/8 or more
• Engine speed : 450 r/min or more
.
TSB Revision
CVT
DIAGNOSIS
23A-39
LOGIC FLOW CHARTS (Monitor Sequence)
START
Yes
No
Transmission fluid tempereture
< -20 (-4 )
Yes
Accumulated time No
600 sec
Yes
Yes
Accumulated time No
600 sec
Yes
0 (32 ) Transmission fluid No
temperature < 20 (68 )
Yes
Accumulated time No
600 sec
Yes
Malfunction Good
END
AC802605
TSB Revision
23A-40 CVT
DIAGNOSIS
DIAGNOSTIC PROCEDURE
TSB Revision
CVT
DIAGNOSIS
23A-41
TRANSAXLE
CONTROL MODULE
CVT
ASSEMBLY
TRANSMISSION FLUID
TEMPERATURE
SENSOR
ACA03449
ACA03039AH ACA03038 BU
Connector: B-120
B-120 (B)
ACA03088AD
TSB Revision
23A-42 CVT
DIAGNOSIS
START
No
Transmission fluid 180 ˚C (356 ˚F)
Yes
No
Continuous failure for 5 sec
Yes
Yes
Malfunction Good
END
AC803636
Judgment Criteria
.
TSB Revision
CVT
DIAGNOSIS
23A-43
OBD-II DRIVE CYCLE PATTERN <P0712>
Ignition switch : ON (start the engine and keep it for
10 seconds or more)
MONITOR EXECUTION CONDITIONS
.
TSB Revision
23A-44 CVT
DIAGNOSIS
START
Yes
No
Transmission fluid -40 ˚C (-40 ˚F)
Yes
No
Continuous failure for 5 sec
Yes
Yes
Malfunction Good
END
AC710008
PROBABLE CAUSES
Judgment Criteria • Malfunction of the valve body assembly (Faulty
• Value of temperature of transmission fluid: −40°C transmission fluid temperature sensor)
(-40°F) or less. (5 seconds) • Damaged wiring harness and connectors
.
• Malfunction of TCM
TSB Revision
CVT
DIAGNOSIS
23A-45
DIAGNOSIS
TSB Revision
23A-46 CVT
DIAGNOSIS
FUSIBLE
LINK 36
RELAY BOX
ENGINE
COMPARTMENT
CVT
CONTROL
RELAY
PRIMARY
PULLEY
SPEED
SENSOR
TRANSAXLE
CONTROL MODULE
ACA03452
TSB Revision
CVT
DIAGNOSIS
23A-47
Connectors: A-16, A-17 Connector: B-121
A-16 A-17
B-121 (B)
ACA03039AG ACA03088AE
ACA03414AC ACA03038 BU
DIAGNOSTIC FUNCTION
TCM determines that the malfunction is present (OTHER MONITOR AND SENSOR)
when the primary pulley speed sensor value Other Monitor (There is no temporary DTC stored
changes abruptly or when there is a discrepancy in memory for the item monitored below)
between this sensor and other sensors in sensor • P0712, P0713: Malfunction of the transmission
reading. fluid temperature sensor
. • P0720: Malfunction of secondary pulley speed
DESCRIPTIONS OF MONITOR METHODS sensor
• The status with the secondary pulley speed of • P0725: Malfunction of engine speed
500 r/min or more and with the primary pulley • P0741: Abnormality in lockup function
speed of 150 r/min or less continues for 5 sec- • P0746: Abnormality in hydraulic control system
onds. function
• When the primary pulley speed has dropped • P0841: Abnormality in line pressure sensor func-
abruptly from 1,000 r/min or more to 300 r/min or tion
less, and then it keeps 300 r/min or less for 0.5 • P0868: Secondary pressure drop
seconds continuously. • P1723: Abnormality in speed sensor system
function
.
TSB Revision
23A-48 CVT
DIAGNOSIS
START
No
Primary pulley speed 300
150 r/min
Yes
No
Secondary pulley speed 500 r/min
Yes
No
Continuous for 5 sec
Yes
No
Secondary pulley speed 1000 r/min
Yes
No
Primary pulley speed 300 r/min
Yes
Yes
Malfunction Good
END
AC710009 AB
TSB Revision
CVT
DIAGNOSIS
23A-49
Judgment Criteria OBD-II DRIVE CYCLE PATTERN
• Primary pulley speed [secondary pulley speed: Transmission range: D (Drive the vehicle for 20 sec-
500 r/min or more]: 300 r/min or less. (5 seconds) onds or more while the accelerator opening angle is
• Primary pulley speed [Primary pulley speed at 10 20% or more)
millisecond before: 1,000 r/min or more]: 300
r/min or less. (0.5 second)
.
PROBABLE CAUSES
.
DIAGNOSIS
TSB Revision
23A-50 CVT
DIAGNOSIS
TSB Revision
CVT
DIAGNOSIS
23A-51
FUSIBLE
LINK 36
RELAY BOX
ENGINE
COMPARTMENT
CVT
CONTROL
RELAY
SECONDARY
PULLEY
SPEED
SENSOR
TRANSAXLE
CONTROL MODULE
ACA03454
TSB Revision
23A-52 CVT
DIAGNOSIS
B-119 (B)
ACA03039AG ACA03088AF
ACA03414AC ACA03038 BU
DIAGNOSTIC FUNCTION
TCM determines that the malfunction is present (OTHER MONITOR AND SENSOR)
when the secondary pulley speed sensor value Other Monitor (There is no temporary DTC stored
changes abruptly or when there is a discrepancy in memory for the item monitored below)
between this sensor and other sensors in sensor • P0705: Malfunction of transmission range switch
reading. • P0712, P0713: Malfunction of the transmission
. fluid temperature sensor
DESCRIPTIONS OF MONITOR METHODS • P0715: Malfunction of primary pulley speed sen-
• The status with the primary pulley speed of 1,000 sor
r/min or more and with the secondary pulley • P0725: Malfunction of engine speed
speed of 150 r/min or less continues for 5 sec- • P0741: Abnormality in lockup function
onds. • P0746: Abnormality in hydraulic control system
• When the vehicle speed computed by CVT has function
dropped abruptly from 10 km/h (6.2 mph) or more • P0841: Abnormality in line pressure sensor func-
to 5 km/h (3.1 mph) or less, and then the comput- tion
ing value keeps 5 km/h (3.1 mph) or less for 0.5 • P0868: Secondary pressure drop
seconds continuously. • P1706: Malfunction of throttle signal
• P1723: Abnormality in speed sensor system
function
.
MONITOR EXECUTION
• Transmission range:D Sensor (The sensor below is determined to be
• Throttle valve opening : 1/8 or more normal)
• Transmission range switch
• Transmission fluid temperature sensor
.
TSB Revision
CVT
DIAGNOSIS
23A-53
LOGIC FLOW CHARTS (Monitor Sequence)
START
No
Secondary pulley speed 150 r/min
Yes
No
Primary pulley speed 1,000 r/min
Yes
No
Continuous for 5 sec
Yes
Secondary pulley
No
speed at 10 msec 500 r/min
before
Yes
Secondary No
260 r/min
pulley speed
Yes
No
Continuous for 0.5 sec
Yes
Yes Good
Malfunction
END
AC802623
TSB Revision
23A-54 CVT
DIAGNOSIS
DIAGNOSIS
TSB Revision
CVT
DIAGNOSIS
23A-55
DIAGNOSTIC FUNCTION
TCM detects malfunction of engine speed received (OTHER MONITOR AND SENSOR)
from the ECM by comparing the primary pulley Other Monitor (There is no temporary DTC stored
speed with the secondary pulley speed. in memory for the item monitored below)
. • P0705: Malfunction of transmission range switch
DESCRIPTIONS OF MONITOR METHODS • P0715: Malfunction of primary pulley speed sen-
• Primary pulley speed of 1,000 r/min or more and sor
with the engine speed of 450 r/min or less • P0741: Abnormality in lockup function
• When the differences in rotation between the • P0746: Abnormality in hydraulic control system
engine and the primary pulley, and between the function
engine and the secondary pulley are 1,000r/min • P0841: Abnormality in line pressure sensor func-
or more during direct-coupled operating tion
• CAN communication error occurs between ECM • P0868: Secondary pressure drop
and TCM. • P1706: Malfunction of throttle signal
. Sensor (The sensor below is determined to be
MONITOR EXECUTION normal)
• Transmission range:D • Transmission range switch
• Throttle valve opening : 1/8 or more • Primary pulley speed sensor
.
• Accelerator pedal position sensor
.
TSB Revision
23A-56 CVT
DIAGNOSIS
START
No
Engine revolution < 450 r/min
Yes
No
Primary revolution 1,000 r/min
Yes
Yes
Yes
Yes
Malfunction Good
END
AC803645
DIAGNOSTIC PROCEDURE
TSB Revision
23A-58 CVT
DIAGNOSIS
TRANSAXLE
CONTROL MODULE
CVT
ASSEMBLY
SECONDARY LOCK-UP
PRESSURE SELECTION
SOLENOID SOLENOID
VALVE VALVE
LINE
PRESSURE LOCK-UP
SOLENOID SOLENOID
VALVE VALVE
ACA03455
A-16 A-17
ACA03039AG ACA03038 BW
Connector: B-120
B-120 (B)
ACA03088AD
TSB Revision
CVT
DIAGNOSIS
23A-59
DIAGNOSTIC FUNCTION MONITOR EXECUTION CONDITIONS
TCM determines malfunction by detecting the abnor- (OTHER MONITOR AND SENSOR)
mality in the lockup solenoid valve.
Other Monitor (There is no temporary DTC stored
.
START
Yes
Yes
Yes
Monitored current 1.34 A No
Yes
No
Continuous failure for 1 sec
Yes
Malfunction Good
END
AC710012
TSB Revision
23A-60 CVT
DIAGNOSIS
DIAGNOSIS
TSB Revision
23A-62 CVT
DIAGNOSIS
START
No
Lockup pressure 0.2 MPa (29 psi)
Yes
Yes
No
Continuous failure for 30 secs.
Yes
Yes
Good
Malfunction
END
AC710013
Judgment Criteria
.
DTC SET CONDITIONS • Lock-up pressure: 0.2 MPa (29 psi) or more. (30
Check Conditions seconds)
• Transmission range switch position: D. • Torque converter slip revolution: 40+(vehicle
• Throttle position sensor voltage: 1.37 volts or speed/2) or more. (30 seconds)
more. .
TSB Revision
CVT
DIAGNOSIS
23A-63
DIAGNOSTIC PROCEDURE
TSB Revision
23A-64 CVT
DIAGNOSIS
START
Yes
Yes
Yes
No
PUMonitored
solenoid circuit
currentis ground
1.34 A short
Yes
No
Continuous failure for 1 sec
Yes
Malfunction Good
END
AC609280 AC
PROBABLE CAUSES
• Monitored current: 1.34 A or more. (1 second)
• Malfunction of valve body assembly (Faulty line
.
pressure solenoid valve)
• Damaged wiring harness and connectors
• Malfunction of TCM
TSB Revision
CVT
DIAGNOSIS
23A-65
DIAGNOSTIC PROCEDURE
TSB Revision
23A-66 CVT
DIAGNOSIS
TSB Revision
CVT
DIAGNOSIS
23A-67
LOGIC FLOW CHARTS (Monitor Sequence)
START
No
Pulley ratio > 3.5
Yes
No
Continuous failure for 0.1 sec
Yes
No
Pulley ratio > 2.7
Yes
No
Continuous failure for 0.2 sec
Yes
Yes
Malfunction Good
END
AC609375 AB
Judgment Criteria
.
TSB Revision
23A-68 CVT
DIAGNOSIS
DIAGNOSTIC PROCEDURE
TSB Revision
CVT
DIAGNOSIS
23A-69
DIAGNOSTIC FUNCTION
TCM conducts fault detection by measuring the dif- 3. Difference between target secondary pressure
ference between the target value and the actual and actual secondary pressure is 1.20 MPa (174
value for the secondary pressure. psi) or more.
.
PROBABLE CAUSES
.
JUDGMENT CRITERIA
The following three conditions are met for three sec- • Trouble in CAN bus system
onds. • Abnormal line pressure
• Malfunction of TCM
1. Engine speed is 450 r/min or more.
DIAGNOSTIC PROCEDURE
TSB Revision
23A-70 CVT
DIAGNOSIS
TSB Revision
CVT
DIAGNOSIS
23A-71
LOGIC FLOW CHARTS (Monitor Sequence)
START
Yes
Yes
Yes
No
SECMonitored current
solenoid circuit 1.34 Ashort
is ground
Yes
No
Continuous failure for 1 sec
Yes
Malfunction Good
END
AC609342 AD
PROBABLE CAUSES
• Monitored current: 1.34 A or more. (1 second)
• Malfunction of valve body assembly (Faulty sec-
.
ondary pressure solenoid valve)
• Damaged wiring harness and connectors
• Malfunction of TCM
TSB Revision
23A-72 CVT
DIAGNOSIS
DIAGNOSIS
TSB Revision
CVT
DIAGNOSIS
23A-73
DTC P0815: Malfunction of Paddle Shift Up Switch <Vehicles with paddle shift>
TRANSAXLE
CONTROL MODULE
PADDLE
SHIFT
SWITCH
JOINT
CONNECTOR (4)
GROUNDING
CONNECTOR
ACA03456
C-127
ACA03038 BX
ACA03078 AH
Connector: C-131
ACA03038 BW
TSB Revision
23A-74 CVT
DIAGNOSIS
DIAGNOSTIC FUNCTION
.
PROBABLE CAUSES
TCM detects that the paddle shift UP switch is stuck • Malfunction of paddle shift switch
to ON. • Damaged wiring harness and connectors
.
• Malfunction of TCM
JUDGMENT CRITERIA
When the paddle shift UP switch being ON consecu-
tively for 60 seconds is detected.
DIAGNOSTIC PROCEDURE
TSB Revision
CVT
DIAGNOSIS
23A-75
JUDGMENT CRITERIA
.
DIAGNOSTIC PROCEDURE
TSB Revision
23A-76 CVT
DIAGNOSIS
TRANSAXLE
CONTROL MODULE
SELECTOR
SHIFT SELECT LEVER
SWITCH SWITCH ASSEMBLY
SPORT AUTO
MODE MODE
JOINT
CONNECTOR (4)
GROUNDING
CONNECTOR
ACA03159
C-127
ACA03036 AW ACA03038 BX
TSB Revision
CVT
DIAGNOSIS
23A-77
Connector: C-130
ACA03038 BU
. .
DIAGNOSIS
TSB Revision
23A-78 CVT
DIAGNOSIS
TSB Revision
CVT
DIAGNOSIS
23A-79
CVT
ASSEMBLY
SECONDARY
PRESSURE
SENSOR
ACA03460
ACA03039AH ACA03038 BU
Connector: B-120
B-120 (B)
ACA03088AD
DIAGNOSTIC FUNCTION
TCM conducts fault detection by monitoring the out- • The status with the fluid temperature of −20°C
put voltage of the secondary pressure sensor. (−4°F) or more and with the secondary pressure
sensor voltage of 4.69 volts or more continues for
.
5 seconds.
TSB Revision
23A-80 CVT
DIAGNOSIS
• The status with the fluid temperature of −20°C MONITOR EXECUTION CONDITIONS
(−4°F) or more and with the secondary pressure (OTHER MONITOR AND SENSOR)
sensor voltage of 0.09 volt or less continues for 5
seconds. Other Monitor (There is no temporary DTC stored
in memory for the item monitored below)
• P0746: Abnormality in hydraulic control system
.
MONITOR EXECUTION
function
• Continuous
• P0841: Abnormality in line pressure sensor func-
.
tion
• P0868: Secondary pressure drop
Sensor (The sensor below is determined to be
normal)
• Not applicable
.
TSB Revision
CVT
DIAGNOSIS
23A-81
LOGIC FLOW CHARTS (Monitor Sequence)
START
No
Transmission fluid > -20˚C (-4˚F)
Yes
Secondary pressure No
sensor voltage 4.69 VmA
Yes
Yes
No
Transmission fluid > -20˚C (-4˚F)
Yes
No
Secondary pressure
sensor voltage 0.09 V
Yes
No
Continuous failure for 5 sec
Yes
Malfunction Good
END
AC609343 AD
. .
TSB Revision
23A-82 CVT
DIAGNOSIS
DIAGNOSTIC PROCEDURE
(98 psi) or more, and the status over the target line
pressure remains for 5 seconds.
TSB Revision
CVT
DIAGNOSIS
23A-83
MONITOR EXECUTION CONDITIONS Sensor (The sensor below is determined to be
(OTHER MONITOR AND SENSOR) normal)
• Not applicable
Other Monitor (There is no temporary DTC stored
in memory for the item monitored below)
.
• Not applicable
START
Yes
Yes
Yes
Malfunction Good
END
AC901246
TSB Revision
23A-84 CVT
DIAGNOSIS
Judgment Criteria
.
DIAGNOSTIC PROCEDURE
MONITOR EXECUTION
• Engine speed : 450 r/min or more
TSB Revision
CVT
DIAGNOSIS
23A-85
LOGIC FLOW CHARTS (Monitor Sequence)
START
Yes
Yes
No
Continuous failure for 1.5 sec.
Yes
Fail counter up
Yes
No
Fail counter 2 times
Yes
Malfunction Good
END
AC802627
Judgment Criteria
.
TSB Revision
23A-86 CVT
DIAGNOSIS
PROBABLE CAUSES
Transmission range: D (Drive the vehicle for 10 sec- • Damaged wiring harness and connectors
onds or more while the accelerator opening angle is • Malfunction of CVT assembly
20% or more) • Malfunction of TCM
DIAGNOSTIC PROCEDURE
TSB Revision
CVT
DIAGNOSIS
23A-87
FUSIBLE
LINK 36
RELAY BOX
ENGINE
COMPARTMENT
CVT
CONTROL
RELAY
TRANSAXLE
CONTROL MODULE
ACA03461
ACA03414AC ACA03038 BW
DIAGNOSTIC FUNCTION
TCM monitors if power supply system is normal or
not and judges the trouble.
.
TSB Revision
23A-88 CVT
DIAGNOSIS
PROBABLE CAUSES
• Damaged wiring harness and connectors
• Malfunction of TCM
DIAGNOSTIC PROCEDURE
TSB Revision
CVT
DIAGNOSIS
23A-89
FUSIBLE
LINK 36
RELAY BOX
ENGINE
COMPARTMENT
CVT
CONTROL
RELAY
TRANSAXLE
CONTROL MODULE
ACA03472
C-131
C-130
ACA03414AC ACA03038 BY
DIAGNOSTIC FUNCTION
TCM checks the consistency between EEPROM and • When the ignition switch is turned to the "ON"
the backup memory. position, TCM determines that the writing to the
EEPROM area had failed last time the ignition
.
switch was turned to the "LOCK" (OFF) position.
.
MONITOR EXECUTION
• Continuous
TSB Revision
23A-90 CVT
DIAGNOSIS
START
No
Calculated checksum memorized checksum
Yes
Malfunction Good
END
AC710015
PROBABLE CAUSES
.
• Damaged wiring harness and connectors
• Malfunction of TCM (Faulty EEPROM)
DIAGNOSTIC PROCEDURE
TSB Revision
CVT
DIAGNOSIS
23A-91
TSB Revision
23A-92 CVT
DIAGNOSIS
START
No
Throttle position toggle signal on CAN is fail
Yes
No
Continuous failure for 1 sec
Yes
Secondary
All parameters
secondary parameters No
are in the enable condition.
Yes
Malfunction Good
END
AC609348 AD
. .
TSB Revision
CVT
DIAGNOSIS
23A-93
DIAGNOSTIC PROCEDURE
PROBABLE CAUSES
JUDGMENT CRITERIA • Malfunction of the CAN bus
• Difference between the estimated vehicle speed • Malfunction of TCM
and the one measured before 0.1 second is 29
km/h (18 mph) or more.
DIAGNOSTIC PROCEDURE
TSB Revision
23A-94 CVT
DIAGNOSIS
TSB Revision
CVT
DIAGNOSIS
23A-95
FUSIBLE
LINK 36
RELAY BOX
ENGINE
COMPARTMENT
CVT
CONTROL
RELAY
PRIMARY SECONDARY
PULLEY PULLEY
SPEED SPEED
SENSOR SENSOR
TRANSAXLE
CONTROL MODULE
ACA03473
TSB Revision
23A-96 CVT
DIAGNOSIS
B-119 (B)
B-121 (B)
ACA03039AG ACA03088AG
ACA03414AC ACA03038 BU
DIAGNOSTIC FUNCTION
TCM detects the abnormal wave pattern of the speed (OTHER MONITOR AND SENSOR)
sensor signal. Other Monitor (There is no temporary DTC stored
. in memory for the item monitored below)
DESCRIPTIONS OF MONITOR METHODS • P0741: Abnormality in lockup function
• Rotational fluctuation of primary pulley is large • P0746: Abnormality in hydraulic control system
(for 1 second). function
• Rotational fluctuation of secondary pulley is large • P0841: Abnormality in line pressure sensor func-
(for 1 second). tion
• P0868: Secondary pressure drop
.
TSB Revision
CVT
DIAGNOSIS
23A-97
LOGIC FLOW CHARTS (Monitor Sequence)
START
Noise of primary No
speed sensor > 30 r/min
Yes
Yes
Noise of primary No
speed sensor > 30 r/min
Yes
No
Continuous for 1 sec
Yes
Malfunction Good
END
AC802631
. .
PROBABLE CAUSES
Judgment Criteria
• Malfunction of primary pulley speed sensor
• Noise of primary pulley or primary pulley speed
• Malfunction of secondary pulley speed sensor
sensor signal: more than 30 r/min. (1 second)
• Malfunction of TCM
• Noise of primary pulley or secondary pulley
speed sensor signal: more than 30 r/min. (1 sec-
ond)
TSB Revision
23A-98 CVT
DIAGNOSIS
DIAGNOSTIC PROCEDURE
• Continuous
TSB Revision
CVT
DIAGNOSIS
23A-99
LOGIC FLOW CHARTS (Monitor Sequence)
START
No
No
No
Continuous failure for 0.2 sec
Yes
Malfunction Good
END
AC802632
. .
TSB Revision
23A-100 CVT
DIAGNOSIS
DIAGNOSTIC PROCEDURE
TSB Revision
CVT
DIAGNOSIS
23A-101
JUDGMENT CRITERIA
.
DIAGNOSTIC FUNCTION
TCM conducts fault detection by monitoring the inter- Percentage change in pulley ratio is larger than the
nal calculated value. standard value.
.
PROBABLE CAUSES
.
• Malfunction of TCM
DIAGNOSTIC PROCEDURE
normal)
MONITOR EXECUTION • Not applicable
• When 1.05 seconds have elapsed after TCM
started (not during scan tool communication) .
TSB Revision
23A-102 CVT
DIAGNOSIS
START
No
ABS status is "Malfunction"
Yes
No
Continuous failure for 0.5 sec
Yes
Yes
Malfunction Good
END
AC802633
DIAGNOSTIC PROCEDURE
TSB Revision
CVT
DIAGNOSIS
23A-103
TRANSAXLE
CONTROL MODULE
CVT
ASSEMBLY
STEPPER MOTOR
ACA03474
B-120 (B)
ACA03039AH ACA03088AD
TSB Revision
23A-104 CVT
DIAGNOSIS
Connector: C-130
ACA03038 BU
DIAGNOSTIC FUNCTION
TCM conducts fault detection by monitoring the volt- (OTHER MONITOR AND SENSOR)
age of each coil for stepper motors. Other Monitor (There is no temporary DTC stored
. in memory for the item monitored below)
DESCRIPTIONS OF MONITOR METHODS • P0741: Abnormality in lockup function
• The specified voltage is not applied to each coil • P0746: Abnormality in hydraulic control system
for stepper motors for 0.2 second because of an function
open or short circuit. • P0841: Abnormality in line pressure sensor func-
tion
• P0868: Secondary pressure drop
.
MONITOR EXECUTION
• Continuous Sensor (The sensor below is determined to be
normal)
• Not applicable
.
TSB Revision
CVT
DIAGNOSIS
23A-105
LOGIC FLOW CHARTS (Monitor Sequence)
START
Yes Circuit A or B or C or D
activation command on at circuit voltage 2.8 V
No
Yes Circuit A or B or C or D
activation command off at circuit voltage > 2.8 V
No
No
Continuous failure for 0.2 sec
Yes
Malfunction Good
END
AC802634
PROBABLE CAUSES
• Stepping motor activation command (OFF volt-
• Malfunction of valve body assembly (Faulty step-
age): More than 2.8 volts. (0.2 second)
per motor)
.
• Damaged wiring harness and connectors
• Malfunction of TCM
TSB Revision
23A-106 CVT
DIAGNOSIS
DIAGNOSTIC PROCEDURE
TSB Revision
CVT
DIAGNOSIS
23A-107
JUDGMENT CRITERIA
.
PROBABLE CAUSES
ratio corresponding to stepper motor position)
(Actual measurement value: Actual primary pulley • Malfunction of TCM
speed) • Malfunction of valve body assembly (Faulty step-
per motor)
.
DIAGNOSTIC PROCEDURE
TSB Revision
23A-108 CVT
DIAGNOSIS
DIAGNOSIS
MONITOR EXECUTION
• P1706: Malfunction of throttle signal
• When 1.05 seconds have elapsed after TCM
• P1773: Malfunction of ABS
started
• U0100: CAN time-out error (Engine)
.
TSB Revision
CVT
DIAGNOSIS
23A-109
LOGIC FLOW CHARTS (Monitor Sequence)
START
TCM is started No
Yes
Timer stat
No
Timer > 1.05 secs
Yes
No
CAN communication is fail
Yes
Yes
Malfunction Good
END
AC802635
. .
TSB Revision
23A-110 CVT
DIAGNOSIS
DIAGNOSTIC PROCEDURE
normal)
MONITOR EXECUTION • Not applicable
• When 1.05 seconds have elapsed after TCM
started .
TSB Revision
CVT
DIAGNOSIS
23A-111
LOGIC FLOW CHARTS (Monitor Sequence)
START
No
TCM is started
Yes
Timer start
No
Timer > 1.05 secs.
Yes
No
CAN communication with ECM is fail
Yes
No
Continuous
Continuous failure
failure for 500 msecs.
Yes
Malfunction Good
END
AC609281AC
. .
TSB Revision
23A-112 CVT
DIAGNOSIS
DIAGNOSTIC PROCEDURE
JUDGMENT CRITERIA
.
DIAGNOSTIC FUNCTION
TCM determines that malfunction is present if the TCM cannot receive the periodic communication
periodic communication data sent from the data from ABS-ECU.
ABS-ECU via CAN bus lines is abnormal. .
PROBABLE CAUSES
• Malfunction of the CAN bus
.
• ABS-ECU malfunction
• Malfunction of TCM
DIAGNOSTIC PROCEDURE
TSB Revision
CVT
DIAGNOSIS
23A-113
JUDGMENT CRITERIA
.
DIAGNOSTIC FUNCTION
TCM determines that malfunction is present if the TCM cannot receive the periodic communication
periodic communication data sent from ETACS-ECU data from ETACS-ECU.
via the CAN bus lines is abnormal. .
PROBABLE CAUSES
• Malfunction of the CAN bus
.
• Malfunction of ETACS-ECU
• Malfunction of TCM
DIAGNOSTIC PROCEDURE
TSB Revision
23A-114 CVT
DIAGNOSIS
JUDGMENT CRITERIA
When the TCM coding has not been performed. Q: Is the diagnostic trouble code set?
YES : Diagnose the ETACS-ECU. (Refer to
.
DIAGNOSIS
.
DIAGNOSTIC FUNCTION
TCM checks that the coding information is normal.
.
STEP 1. Using scan tool MB991958, diagnose the
JUDGMENT CRITERIA CAN bus line.
The ETACS-ECU coding information about whether Use the scan tool MB991958 to diagnose the CAN
the AWD-ECU is mounted or not is incorrect. bus lines.
Q: Is the check result normal?
YES : Go to Step 2.
.
PROBABLE CAUSES
NO : Repair the CAN bus lines. (Refer to GROUP
• Malfunction of the CAN bus line
54C − Troubleshooting P.54C-16.)
• ETACS-ECU coding information is abnormal
• ETACS-ECU failure or improper assembly
• Malfunction of TCM STEP 2. Use scan tool MB991958 to confirm a
diagnostic trouble code of other systems.
Check if the ETACS-ECU sets a diagnostic trouble
code.
Q: Is the diagnostic trouble code set?
YES : Diagnose the ETACS-ECU. (Refer to
GROUP 54A − Troubleshooting P.54A-671)
NO : Go to Step 3.
TSB Revision
CVT
DIAGNOSIS
23A-115
STEP 3. ETACS-ECU coding data check STEP 4. Diagnostic trouble code recheck
Using scan tool MB991958, check if any abnormality Check again if the diagnostic trouble code is set to
is present in the coding data below which is stored in TCM.
the ETACS-ECU. (1) Erase the diagnostic trouble code.
Final drive (2) Turn the ignition switch from the "LOCK (OFF)"
OK <FWD vehicles>: Front Drive position to the "ON" position.
OK <AWD vehicles>: 4WD FF Base (3) Check if the diagnostic trouble code is set.
Q: Is the check result normal? Q: Is the diagnostic trouble code set?
YES : Go to Step 4. YES : Replace the TCM.
NO : Repair the coding data. If repair is NO : Intermittent malfunction.
impossible, replace the ETACS-ECU.
SYMPTOM PROCEDURES
FUSIBLE
LINK 36
RELAY BOX
ENGINE
COMPARTMENT
CVT
CONTROL
RELAY
TRANSAXLE
CONTROL MODULE
ACA03461
TSB Revision
23A-116 CVT
DIAGNOSIS
ACA03414AC ACA03038 BW
PROBABLE CAUSES
.
SYMPTOMS
TCM cannot be turned ON. • Damaged wiring harness and connectors
• Malfunction of TCM
.
DIAGNOSIS
TSB Revision
CVT
DIAGNOSIS
23A-117
PROBABLE CAUSES
.
SYMPTOMS
Engine torque is transferred to the driveshaft in the N • Malfunction of the transmission range switch
range, and the vehicle consequently moves forward • Malfunction of CVT assembly
or rearward. • Damaged wiring harness and connectors
• Malfunction of TCM
.
DIAGNOSTIC PROCEDURE
TSB Revision
23A-118 CVT
DIAGNOSIS
DIAGNOSTIC PROCEDURE
PROBABLE CAUSES
.
SYMPTOMS
Vehicle does not creep. Incomplete shifting operation • Malfunction of forward clutch
or extremely poor acceleration is observed. • Malfunction of torque converter
• Malfunction of CVT assembly
.
• Malfunction of valve body assembly
• Malfunction of TCM
DIAGNOSTIC PROCEDURE
TSB Revision
CVT
DIAGNOSIS
23A-119
TRANSAXLE
CONTROL MODULE
SELECTOR
SHIFT SELECT LEVER
SWITCH SWITCH ASSEMBLY
SPORT AUTO
MODE MODE
JOINT
CONNECTOR (4)
GROUNDING
CONNECTOR
ACA03159
TSB Revision
23A-120 CVT
DIAGNOSIS
ACA03036 AW ACA03038 BU
C-127
ACA03038 BX
PROBABLE CAUSES
.
SYMPTOMS
Gears cannot be changed even when the selector • Damaged wiring harness and connectors
lever is moved to "+" or "−" position during sport • Malfunction of TCM
mode. • Malfunction of selector lever assembly (Faulty
shift switch assembly)
.
DIAGNOSTIC PROCEDURE
TSB Revision
CVT
DIAGNOSIS
23A-121
TSB Revision
23A-122 CVT
DIAGNOSIS
Inspection Procedure 6: Cannot be Changed with the Paddle Shift. <Vehicles with paddle shift>
TRANSAXLE
CONTROL MODULE
PADDLE
SHIFT
SWITCH
JOINT
CONNECTOR (4)
GROUNDING
CONNECTOR
ACA03456
C-127
ACA03038 BX
ACA03078 AH
Connector: C-131
ACA03038 BW
TSB Revision
CVT
DIAGNOSIS
23A-123
SYMPTOMS PROBABLE CAUSES
The transaxle does not upshift or downshift when the • Malfunction of paddle shift switch
paddle shift is operated. • Damaged wiring harness and connectors
.
• Malfunction of TCM
DIAGNOSTIC PROCEDURE
TSB Revision
23A-124 CVT
DIAGNOSIS
Inspection Procedure 7: The fluid temperature warning lamp illuminates too frequently.
DIAGNOSIS
TSB Revision
CVT
DIAGNOSIS
23A-125
B
A
TSB Revision
23A-126 CVT
DIAGNOSIS
TSB Revision
CVT
DIAGNOSIS
23A-127
Item Display on scan Check conditions Normal conditions
No. tool
20 Transmission fluid Ignition switch: ON Transmission fluid 39 − 55 count
temperature* temperature: Approximately
20°C (68°F)
Transmission fluid 152 − 170 count
temperature: Approximately
80°C (176°F)
21 Vehicle speed Driving conditions Nearly the same as
(inference) the speedometer
display
22 Real vehicle speed Driving conditions Nearly the same as
the speedometer
display
26 Real step Driving conditions −20 to 190 step
30 LU solenoid monitor From lockup release to engage 0 − 0.7 A
current
31 LU solenoid output From lockup release to engage 0 − 0.7 A
current
32 Line pressure SOL. • Engine: Idling 0.45 − 0.75 A
monitor current • Transmission range: N
Engine: Stalled 0.08 − 0.3 A
33 Line pressure SOL. From low line pressure to high line pressure 0 − 0.8 A
output current
34 Secondary PRS. • Engine: Idling 0.45 − 0.75 A
SOL. monitor current • Transmission range: N
Engine: Stalled 0.08 − 0.3 A
35 Secondary PRS. From low secondary pressure to high secondary 0 − 0.8 A
SOL. monitor output pressure
current
36 LU/SEL changeover Ignition switch: ON Transmission range: P, N ON
SOL. output Transmission range: 5 or OFF
more seconds have passed
after the selector lever has
been moved to R or D
position.
37 LU/SEL changeover Ignition switch: ON Transmission range: P, N ON
SOL. monitor Transmission range: 5 or OFF
more seconds have passed
after the selector lever has
been moved to R or D
position.
38 Stepper motor coil A Driving conditions ON/OFF switches
alternately.
39 Stepper motor coil B Driving conditions ON/OFF switches
alternately.
TSB Revision
23A-128 CVT
DIAGNOSIS
TSB Revision
CVT
DIAGNOSIS
23A-129
Item Display on scan Check conditions Normal conditions
No. tool
54 Paddle switch (up) • Ignition switch: ON Paddle shift lever position: ON
<Vehicles with • Engine: Stopped Upshift and hold
paddle shift> Paddle shift lever position: OFF
Other than the above
55 Paddle switch • Ignition switch: ON Paddle shift lever position: ON
(down) <Vehicles • Engine: Stopped Downshift and hold
with paddle shift> Paddle shift lever position: OFF
Other than the above
56 ABS actuation signal ABS operated ON
ABS not operated OFF
59 Shift position • Ignition switch: ON Transmission range: P P, N
• Engine: Stopped Transmission range: R R
Transmission range: N P, N
Transmission range: D D
60 Gear position (SP Transmission range: Idling 1st
mode) Sport mode Drive at a constant speed of 2nd
30 km/h (19 mph) in 2nd
gear.
Drive at a constant speed of 3rd
35 km/h (22 mph) in 3rd
gear.
Drive at a constant speed of 4th
40 km/h (25 mph) in 4th
gear.
Drive at a constant speed of 5th
50 km/h (31 mph) in 5th
gear.
Drive at a constant speed of 6th
60 km/h (37 mph) in 6th
gear.
NOTE: *: Relation between fluid temperature and
300 (572)
COUNT is shown to the characteristics chart. 250 (482)
Fluid temperature ˚C (˚F)
200 (392)
150 (302)
100 (212)
50 (122)
0 (32)
-50 (-58)
-100 (-148)
0 50 100 150 200 250 300
Count
AC508704 AB
TSB Revision
23A-130 CVT
DIAGNOSIS
C-131 C-130
JAE-E JAE-E
1 2 3 4 5 6 7 8 9 10 11 12 13 31 32 33 34 35 36 3738 39 40 41
14 15 16 17 18 19 20 21 22 23 24 25 26 4243 44 45 46 47 48 49 50 51 52
AC506684AP
TSB Revision
CVT
DIAGNOSIS
23A-131
Terminal Check item Check conditions Standard value
No.
22 Paddle shift switch (up) Ignition switch: ON Paddle shift lever 1 V or less
<Vehicles with paddle shift> position: Upshift and
hold
Paddle shift lever Battery positive
position: Other than voltage
the above
25 Power supply Ignition switch: ON Battery positive
voltage
Ignition switch: OFF 1 V or less
26 Ground Always 1 V or less
31 Back-up power supply Always Battery positive
voltage
32 Transmission range switch • Ignition switch: ON Battery positive
P • Transmission range: P voltage
• Ignition switch: ON 1 V or less
• Transmission range: Other than P
33 Transmission range switch • Ignition switch: ON Battery positive
R • Transmission range: R voltage
• Ignition switch: ON 1 V or less
• Transmission range: other than R
34 Transmission range switch • Ignition switch: ON Battery positive
N • Transmission range: N voltage
• Ignition switch: ON 1 V or less
• Transmission range: Other than N
35 Select switch Ignition switch: ON Transmission range: 1 V or less
Sport mode
Transmission range: Battery positive
Other than the above voltage
36 Secondary pulley rotation • Transmission range: D Oscilloscope
sensor • Drive at a constant speed of Approximately inspection
20 km/h (12 mph) procedure (Refer
• Use an oscilloscope to measure the voltage to P.23A-132.)
between the terminals No.36 and No.26.
37 Primary rotation sensor • Transmission range: D Oscilloscope
• Drive at a constant speed of Approximately inspection
20 km/h (12 mph) procedure (Refer
• Use an oscilloscope to measure the voltage to P.23A-132.)
between the terminals No.37 and No.26.
39 Secondary pressure sensor • Engine: Idling Approximately
• Transmission range: N 1.0 V
40 Stepper motor A Within 2 seconds after the ignition switch is Pulse width: 30
turned to the ON position ms
41 Stepper motor B Within 2 seconds after the ignition switch is Pulse width: 10
turned to the ON position ms
TSB Revision
23A-132 CVT
DIAGNOSIS
TSB Revision
CVT
SPECIAL TOOLS
23A-133
SPECIAL TOOLS
M1231200600611
MB992006
TSB Revision
23A-134 CVT
SPECIAL TOOLS
MB991895
MB992201 −
Engine hanger
plate
B992201
MB991527 −
Engine hanger
B991527
TSB Revision
CVT
ON-VEHICLE SERVICE
23A-135
ON-VEHICLE SERVICE
CVT CONTROL COMPONENT LAYOUT
M1231208600336
A B C G H
D E F I J K L
ACA03534AB
A B
Secondary pulley
speed sensor
Crank shaft
position sensor
Drive shaft (RH)
Transaxle control
cable
AC605661AC AC506574AZ
TSB Revision
23A-136 CVT
ON-VEHICLE SERVICE
C D
Transmission range switch
Primary pulley
speed sensor
AC607297AH AC610051AC
TCM Brake
pedal
AC606956AC AC609992AC
I J
Data link connector
Stoplight switch
Brake pedal
ETACS-ECU
ACA03535AB AC004673AH
TSB Revision
CVT
ON-VEHICLE SERVICE
23A-137
K L
Accelerator pedal
position sensor
Shift lock
solenoid
AC905354AF
ACA03315AB
ESSENTIAL SERVICE
CAUTION
Replace the transmission fluid whenever the transaxle is
replaced with a new one or the vehicle is driven in harsh
conditions.
1. Drive the vehicle until the transmission fluid is warmed up to
the normal operating temperature 70 − 80°C (158 − 176°F).
NOTE: Use scan tool MB991958 to measure the transmis-
sion fluid temperature.
NOTE: When a certain amount of time is required to warm
Fluid level mm (in) up the transmission fluid to the normal operating tempera-
10 (0.4) ture 70 − 80°C (158 − 176°F), check the oil level referring to
0 (0) the characteristics chart.
HOT
TSB Revision
23A-138 CVT
ON-VEHICLE SERVICE
5. Check that the transmission fluid level is within the "H" area
on the dipstick. If the fluid level is low, add the transmission
fluid to the "H" level.
Transmission fluid: DIA QUEEN CVTF-J1
NOTE: When the transmission fluid level is low, the oil pump
sucks air together with the transmission fluid, and produces
air bubbles in the hydraulic circuit. The air bubbles in the
hydraulic circuit decreases the hydraulic pressure, causing
the delayed shift or slippage of the belt, clutch, and brake.
AC805082 When the transmission fluid level is too high, the fluid is
stirred by the gear and foams up, and the problems similar
to those when the transmission fluid level is low will occur. In
either case, air bubbles cause the overheat and oxidation of
the transmission fluid, which prevents normal operation of
the valve, clutch, and brake. Beside, when the transmission
fluid is foamy, it flows out of the transaxle vent hole. This
may be taken as the fluid leakage by mistake.
6. Insert the dipstick securely.
TSB Revision
CVT
ON-VEHICLE SERVICE
23A-139
8. Drive the vehicle until the transmission fluid is warmed up to
the normal operating temperature 70 − 80°C (158 − 176°F),
and check the transmission fluid level. It must be within the
"H" area on the dipstick.
NOTE: The "COLD" level is for reference only. Use the "H"
level as the criteria.
NOTE: Use scan tool MB991958 to measure the transmis-
sion fluid temperature.
NOTE:
AC805082
TSB Revision
23A-140 CVT
ON-VEHICLE SERVICE
TSB Revision
CVT
ON-VEHICLE SERVICE
23A-141
CAUTION
With the fluid set at the proper level, transmission fluid
collection should not exceed one quart or internal damage
to the transaxle may occur.
1. Disconnect the OUTLET line (from cooler) at the transaxle
and place a collecting container under the disconnected line.
From 2. Run the engine at curb idle speed with the shift selector in
cooler neutral.
To cooler 3. If transmission fluid flow is intermittent or it takes more than
20 seconds to collect one quart of transmission fluid, replace
the cooler.
4. If flow is within acceptable limits, reconnect the cooler line.
Then fill the transaxle to the proper level, using DIA QUEEN
AC611029AB
CVTF-J1.
P L
<Vehicles without
R sport mode>
N D
AC507184 AC
TSB Revision
23A-142 CVT
ON-VEHICLE SERVICE
4. Align the hole at the end of the manual control lever and the
hole in the transmission range switch body flange (section A
− A).
NOTE: Insert a φ5 bar into the aligned holes in the transmis-
sion range switch body flange and on the tip of the manual
Manual control lever to position the transmission range switch body.
control lever
A A
Section A - A
End hole
Manual
control lever
Flange hole
Transmission range
switch body
AC507417AF
AC610050 AC
Filler plug
Drain plug
AC506489AB
TSB Revision
CVT
ON-VEHICLE SERVICE
23A-143
2. Check that the oil level is not 18 mm below the bottom of the
Filler plug hole oil filler plug hole.
Transfer oil Gasket
3. Check that the oil is not excessively foul and has moderate
viscosity.
4. If the oil level is not in between the upper limit and the lower
Upper limit, refill the specified oil to the bottom of the oil filler plug
limit
hole.
Lower Oil filler plug
limit Brand name: Hypoid gear oil API classification GL-5
18 mm
SAE 80
AC700330 AT
5. Install the filler plug and new gasket, and tighten to the
specified torque.
Tightening torque: 32 ± 2 N⋅m (24 ± 1 ft-lb)
Filler plug
Transfer oil
AC700330AG
TSB Revision
23A-144 CVT
ON-VEHICLE SERVICE
ACA03414AB
TSB Revision
CVT
ON-VEHICLE SERVICE
23A-145
CAUTION
Each solenoid valve cannot be removed or replaced as a
single unit. When replacement of any one of the solenoid
valves is necessary, replace the valve body assembly.
4. When the resistance is outside the standard value, replace
the valve body assembly and the harness.
1 2 3 4 5
6 7 8 9 10 11
12 13 14 15 16 17
18 19 20 21 22
AC610481AB
CAUTION
Insert a thermometer which is made of metal or is put in a
metal case (overall length: approximately 150 − 200 mm)
into the transaxle case hole approximately 80 mm.
Transaxle case hole
2. Remove the oil filler tube assembly (Refer to Transaxle
Assembly), and insert a thermometer into the transaxle case
CVT ASSY
connector
hole.
NOTE: If a radiation thermometer (noncontact thermometer)
is available, use it to measure the surface temperature of the
oil pan.
AC807711AD 3. Measure the resistance between the sensor-side connector
terminal No.17 of the CVT assembly connector and ground
(terminal No.19).
Standard value:
TSB Revision
23A-146 CVT
ON-VEHICLE SERVICE
AC609992AB
4. In the cases other than the above, replace the paddle shift
assembly.
TSB Revision
CVT
ON-VEHICLE SERVICE
23A-147
SELECTOR LEVER OPERATION CHECK
M1231202900403
1. Put on the parking brake.
2. Move the selector lever to every range and check that the
lever moves smoothly with secure feel of engagement.
3. Make sure that the engine starts when the selector lever is in
P the N or P range, and does not start when the selector lever
is in other range.
R 4. Start the engine. Release the parking brake.
N 5. Make sure that the vehicle moves forward when the selector
lever is moved from the N range to D range, or to the 1st to
D 6th speed in the sports mode. Also make sure that the
vehicle moves backward when the selector lever is moved
from the N to R range.
6. Stop the engine.
: Turn the ignition switch to the 7. Turn ON the ignition switch, and move the selector lever
"ON" position, and operate the lever from the P to R range. Check that the backup lamp comes
while depressing the brake pedal.
on and the tone alarm sounds at this time.
: Only shifting NOTE: Since the vehicle is equipped with the CVT
wrong-operation preventive device, the selector lever cannot
: Automatic return be moved out of the P position without depressing the brake
pedal after turning ON the ignition switch.
AC703193 AB
TSB Revision
23A-148 CVT
ON-VEHICLE SERVICE
SYSTEM CHECK
Inspection Check conditions Items to be checked Possible cause of abnormality
procedure (Normal conditions)
1 Brake pedal not Ignition switch The selector lever • Abnormality in the shift lock
depressed position: Other cannot be moved out link (stuck, disengaged,
than "ON" of the "P" position broken, etc.)
• Abnormality in the electrical
circuit
2 Brake pedal • Abnormality in the electrical
depressed circuit
3 Brake pedal not Ignition switch • Abnormality in the shift lock
depressed position: "ON" link (stuck, disengaged,
broken, etc.)
• Abnormality in the electrical
circuit
4 Brake pedal The selector lever can • Abnormality in the shift lock
depressed be moved from the "P" link (stuck, disengaged,
position to other broken, etc.)
positions smoothly. • Abnormality in the electrical
circuit
5 Shift lock release • Abnormality in the shift lock
button pressed link (stuck, disengaged,
broken, etc.)
6 Brake pedal The selector lever can • Abnormality in the shift lock
depressed / not be moved from the "R" link (stuck, disengaged,
depressed position to the "P" broken, etc.)
position smoothly.
TSB Revision
CVT
TRANSAXLE CONTROL
23A-149
TRANSAXLE CONTROL
REMOVAL AND INSTALLATION
M1231203200731
WARNING
Be careful not to subject the SRS-ECU to any shocks during removal and installation of the
transaxle control cable assembly.
Post-installation operation
• Shift lock mechanism check (Refer to P.23A-148.)
• Selector lever operation check (Refer to P.23A-147.)
• Transmission range switch and control cable adjustment
(Refer to P.23A-141.)
5 1
4.3 ± 0.7 N·m
38 ± 6 in-lb
7.0 ± 3.0 N·m
6 43 ± 26 in-lb 2
9.5 ± 3.5 N·m
84 ± 30 in-lb
AC905274AC
TSB Revision
23A-150 CVT
TRANSAXLE CONTROL
TSB Revision
CVT
TRANSAXLE ASSEMBLY
23A-151
TRANSAXLE ASSEMBLY
REMOVAL AND INSTALLATION
M1231203600955
<FWD>
10
9.5 ± 3.5 N·m
8.5 ± 3.5 N·m 84 ± 30 in-lb
75 ± 30 in-lb 25 ± 4 N·m
18 ± 3 ft-lb
5
9
2
36 ± 9 N·m 48 ± 6 N·m
27 ± 6 ft-lb 13 36 ± 4 ft-lb
N 11
8 1
12 49 ± 3 N·m
7 17 36 ± 2 ft-lb
13
15
3 14 N
4
16 (Transmission fluid)
6 90 ± 10 N·m
67 ± 7 ft-lb
18
53 ± 8 N·m
40 ± 5 ft-lb
AC904549AE
TSB Revision
23A-152 CVT
TRANSAXLE ASSEMBLY
<AWD>
10 9.5 ± 3.5 N·m
84 ± 30 in-lb
8.5 ± 3.5 N·m 25 ± 4 N·m
75 ± 30 in-lb 18 ± 3 ft-lb
5
9 48 ± 6 N·m
2 36 ± 4 ft-lb
8 13
N 11
7 1
12
49 ± 3 N·m
13 3 36 ± 2 ft-lb
36 ± 9 N·m
15
14 N
17 4
(Transmission fluid)
6 90 ± 10 N·m
16 67 ± 7 ft-lb
18
AC904550AD
TSB Revision
CVT
TRANSAXLE ASSEMBLY
23A-153
REMOVAL SERVICE POINTS
.
AC610049AB
AC905012AC
TSB Revision
23A-154 CVT
TRANSAXLE ASSEMBLY
AC904579AD
MB991527
MB992201 AC904576 AC
MB991929
MB991933
MB991930
MB991932 AC904574AD
TSB Revision
CVT
TRANSAXLE ASSEMBLY
23A-155
(3) Set the chain to hanger (special tool: MB991527) to
support the engine and transaxle assembly. Remove the
MB991928 garage jack and then remove the transaxle assembly
upper part coupling bolts that have been loosened
previously.
AC904575AD
MB991895
AC904578AC
AC904577AC
Approximately
13 mm (0.5 in)
Torque converter
AC209056AF
TSB Revision
23A-156 CVT
TRANSAXLE ASSEMBLY
AC905012AC
A A
Section A - A
End hole
Manual
control lever
Flange hole
Transmission range
switch body
AC507417AF
Adjusting nut
AC610050 AC
TSB Revision
CVT
TRANSFER ASSEMBLY <AWD>
23A-157
TRANSFER ASSEMBLY <AWD>
REMOVAL AND INSTALLATION
M1231211000345
69 ± 9 N·m
51 ± 6 ft-lb
3N
1
(Transmission fluid)
69 ± 9 N·m
51 ± 6 ft-lb
53 ± 8 N·m
39 ± 5 ft-lb
AC905063AF
TSB Revision
23A-158 CVT
TRANSAXLE CONTROL MODULE (TCM)
CAUTION
To store the change pulley ratio status of the transaxle assembly in the TCM memory, drive the vehi-
cle at 3 km/h (1.9 mph) or faster after replacing the TCM.
Pre-removal and post-installation operation
• Bottom Cover (Driver’s Side) Removal and Installation
(Refer to GROUP 52A, Instrument Lower Panel P.52A-8.)
13 ± 2 N·m
115 ± 17 in-lb
2
13 ± 2 N·m
115 ± 17 in-lb
AC610212AC
TSB Revision
CVT
TRANSMISSION FLUID COOLER AND COOLER LINE
23A-159
TRANSMISSION FLUID COOLER AND COOLER LINE
REMOVAL AND INSTALLATION
M1231212500310
25 ± 4 N·m
9.5 ± 3.5 N·m 18 ± 3 ft-lb
84 ± 31 in-lb 1 5
9
6
9.5 ± 3.5 N·m
84 ± 31 in-lb 4
3
7 2
10
ACA00131AC
TSB Revision
23A-160 CVT
TRANSMISSION FLUID COOLER AND COOLER LINE
Stick [6 mm (0.24 in) in diameter] 1. Obtain a container filled with water and place the thermo
valve in it with a stick [approximately 6 mm (0.24 inch) in
diameter] inserted. Gradually warm up the water while
Thermo stirring, and check that the thermo valve opening
valve temperature is within the standard value. The stick rises
when the thermo valve opens.
Standard value:
75 ± 1.5°C (167 ± 2.7°F)
2. Warm up the water to the full-open temperature of the
AC506983AB
thermo valve, and check that the valve lift amount is within
the standard value.
Standard value:
Full-open temperature 95°C (203°F) or more
Valve lift amount when it is fully opened:
3 mm (0.12 inch) or more
NOTE: Measure the height of the fully closed valve in
advance, and then measure the valve height at fully open
temperature to calculate the lift amount.
TSB Revision