Me6601 Dts Unit I Study Notes 1460725816005
Me6601 Dts Unit I Study Notes 1460725816005
UNIT - I
STUDY NOTES
Prepared by:
R. SENDIL KUMAR, AP/MECH
P. SIVA KUMAR, AP/MECH
R. ELAVARASAN, AP/MECH
DHANALAKASHMI COLLEGE OF ENGINEERING
UNIT - I
Selection of V Belts and Pulleys – Selection of Flat belts and Pulleys –Wire ropes and pulleys –
Selection of Transmission chains and Sprockets. Design of pulleys and sprockets.
Introduction
To transmit power, flexible elements such as belts chains and ropes are frequently used. Pullerys
are mounted on a shaft and a continuous belt or rope is passed over them. In belt and ropes,
power is transmitted due to friction between them and pulleys. In case of chain drives, sprocket
wheels are used.
Classification of Drives
Drives
Chain
Types of Belts
1. Flat Belts
2. V – Belts
3. Ribbed Belts
4. Toothed or timing belts
FLAT BELTS
V-BELTS
RIBBED BELTS
It depends on
Power to be Transmitted
Speed of Driver and Driven Shafts
Shaft relationship
Service conditions
Speed reduction ratio
Centre distance
Positive drive requirement
Space available
Used with shafts arranged parallel and when an open belt drive cannot be used due to small angle
of contact on the smaller pulley.
Idler pulleys also known as jockey pulleys are provided to obtain high velocity ratio and when
the required belt tension can not be obtained by other means.
Used when it is desired to transmit motion from one shaft to several parallel shafts
Used with shafts arranged parallel and rotating in the opposite directions.
Used with shafts arranged at right angles and rotating in one definite directions
Used for changing the speed of the driven shaft while the main or driving shaft runs at constant
speed.
Used when the driven shaft is to be started or stopped whenever desired without interfering with
the driving shaft.
8. Compound drive
Used when several units are to be driven from one central shaft.
Belt Materials
High C.O.F
Flexibility
Durability
Strength
1. Leather Belts
made of animal hides
Leathers for belting may be tanned with oak, or chrome salts.
Oak tanned belt is fairly stiff
Chrome tanned leather is soft and pliable
Belts specified according to number of layers as single ply, double ply or triple ply belts.
Double belts or triple belts are made by cementing two or three strips together with hair sides
outside.
3. Rubber Belts
These belts are made up of plies of fabric impregnated with vulcanized rubber or
synthetic rubber.
Easily made endless.
Saw mills, creameries, chemical plants and paper mills largely use rubber belts
4. Balata Belts
Balata is gum similar to rubber. Balata belts are made in the same manner as the rubber belts
made. They are acid proof and water proof. These belts cannot be used at temperatures above
40°C, because at this temperature it softens and became sticky.
The ratio between the speeds of the driver and driven respectively.
N2/N1 = (D + t)/(d + t)
Slip is defined as the relative motion between the belt and pulley.
The difference between the linear speed of the pulley rim and belt is the measure
of slip.
The reason is, there is a tendency for the belt to carry with it on the underside
between the pulley and the belt. The frictional grip between the pulley and the grip is
insufficient.
= (D+t)/(d+t) [1 – (S/100)]
Law of Belting
Lawof belting states that, the centre line of the belt, as it approaches the pulley, must lie in a
plane perpendicular to the axis of that pulley or must lie in the plane of the pulley. Otherwise the
belt will run off the pulley
P = (T1 – T2 ) v watts
As the belt moves round the pulley it would experience a centrifugal force which has the
tendency to separate the belt from the pulley surface.
To maintain the contact between pulley and belt, the centrifugal force produce additional tension
in the belt, this is known as the centrifugal tension.
Tc = mV2
Initial tension
T = T1 + Tc
=σbt
b = width in m
t = thickness in m
T1/T2 = eµα
Considering centrifugal tension
Tension ratio =
Tt1/Tt2 = (T1-mV2)/(T2 - mV2) = eµα
Where
The power transmitted is maximum when the centrifugal tension Tc is one third of the
maximum tension (T).
(i.e) T = 3 Tc
Stresses in belt
2) Due to bending
σb = (E x t)/d.
since ρ = m/(bxt)
Step 1 From the given data determine the design power using the following
procedure
a. From the center distance and dia of pulley find speed ration (I) XI + i = dia of
larger pulley / dia of smaller pulley.
i = Speed of smaller pulley
c. Determine the arc of contact from page 7.5A of data book and select the rating of
the belt at 10 m/s and 180 o
d. Determine the power rating for the belt for the actual velocity and the actual arc of
contact.
e. Fix the number of plies and calculate the rating of the belt.
Step 2 Determine the width of the belt using the formula width
Load Rating
Step 5 Do the pulley design, Calculate the dia of pulley, width of the pulley and
thickness of the pulley in from page No. 7.57
Step 6 Draw the neat diagram of pulley with dimensions.
PART – A
Cross Belt drive: Used with shafts arranged parallel and rotating in opposite direction.
6. Give any three applications of chain drive. What are their limitations? (A/M 2011)
Chain drives are widely used in transportation industry, agricultural industry, metal and
wood working machines.
Limitations: Chain drives cannot be used for velocity ratio more than 10.
7. Mention the materials used for making belts. (N/D 2011) (M/J 2013)
i. Leather
ii. Fabric and cotton
iii. Rubber
iv. Balata and
v. Nylon
8. Give the advantages of chain drives over belt drives. (M/J 2012)
i. Chain drives can be used for long as well as short Centre distances.
ii. They are more compact than belt drive.
iii. There is no slip between chain and sprocket. So they provide positive drive.
9. Explain the term “crowing of pulley”. (M/J 2011)
The pulley rims are tapered slightly towards the edges. This slight convexity is known as
Crowning.
10. In what way silent chain is better than ordinary driving chain? (M/J 2011)
Silent chains are preferred for high-power, high-speed, and smooth operation.
PART - B
Problem 1
Design a flat belt to transmit 12 kw at 450 rpm for an engine to a shaft running at
1200 rpm the dia of engine pulley is 600 mm and centre distance 2 m
Given data
P = 12 kw
N = 450 rpm
n = 1200 rpm
D = 600 mm
CD = 2m
Step 1: i
n 1200
a. Speed ratio i = = = 2.667
N 450
i = 2.667
D 600
i= = 2.667=
d d
d = 225 m
b. Velocity
V = 14.137 m/s
C. Arc of Contact 7.54(PSG Data Book)
D-d
Arc of Contact Q = 180 - x 60
C
0.600 – 0.225
= 180 - x60
2
Selecting high speed belt load rating of belt at 180 o and 10 m/s
14.137 168.78
= 0.023 x x
10 180
Step 1: i
n 1200
a. Speed ratio i = = = 2.667
N 450
i = 2.667
Problem 2
In electric motor drives the exhaust fan using flat belt design the belt drive as per the
following specification a center distance between the pulley is 2.5 m. The permissible
stress on the belt is 2.5 n/mm2 the thickness of the belt is 5 mm and its able to transmit
22.5 kw check the width of the belt using standard formula .
Driver Driven
Diameter (mm)
(Motor Pulley) (Fan pulley)
0.3 0.25
Speed (rpm) 700 ?
Given
P = 225 kw
d = 400 rpm
D = 1600 mm
CD = 2.5 m
Step 1:
D 1600
a. Speed ratio i = = = 4
d 400
i =4
n 700
i = = = 175 rpm
N 4
V = 14.66 m/s
C. Arc of Contact
D-d
Arc of Contact Q = 180 - x 60
C
1.600 – 0.400
= 180 - x60
2
Selecting high speed belt load rating of belt at 180 o and 10 m/s
0.023 kw / mm / ply
14.66 151.2
= 0.023 x x
10 180
No. of plies = 8
ks = 1
kc = 1.08
Width = 200 mm
= 200 + 25 = 225 mm
Length belt
(D-d) 2
L = 2c + (D+d)+
2 4c
(1.5) 2
L=5+ (2)+
2 10
= 829m
Specification
No.of plies = 8
= 12.5 mm
= 48.33 mm
= 34.26 mm
= 35.31 mm
= 24.46 mm
Power (T1-T2)V
= 1534.78
T1 = 2.11T2
T21.117 = 1534.78
T2 = 134.04
T1 = 2908.79
Max Tension T = 8n t
T= T1 + TC
T = T1
2908.79 = 86 x 2.3 x 5
b = 252.9 mm
b = 253mm
Selecting high speed belt load rating of belt at 180o and 10m/s
18.649 157.5
= 0.023 x x
10 180
No. of plies = 5
= 0.1895 kw/mm
g. Design Power
ks = 1
kc = 1.08
Problem 3
Design a flat belt drive for a tan running at 360 rpm which is driven by 10kw, 1440 rpm
belt drive is open type when the space available for centre distance 2m approximately
diameter of driven pulley is 1000 mm.
Given
n = 1440 rpm
N = 360 rpm
P = 10 kw
c = 2m
CD = 1000 mm
Solution
1. Calculation of Pulley dia
D n
=
d N
1000
d = =250mm
4
3. Arc of Contact
D-d
o
Arc of Contact Q = 180 - x60 o
C
4. Selecting high speed belt load rating of belt at 180 o and 10 m/s
= 0.023 kw / mm / ply
18.849 157.5
= 0.023 x x
10 180
= 0.0379 kw/mm/ply
= 11.11 / 0.1896
= 76 + 13 = 89 mm
(D-d) 2
L = 2c + (D+d)+
2 4c
(1-0.25) 2
L= 2x2+ (1+0.25)+
2 4 x2
L = 6.033m
Initial tension
= 60.33 mm
= 5972.96 mm
Specification
Pulley width = 89 mm
Pulley Design
Selecting CI Pulley
Driver pulley = 3
2.94 (89 x 1000)/(4x6)
= 45.506 mm
= 2/3 x 45.506
= 30.33
r = (3 / 4) x 45
= 33.75 mm
Problem 4
Design a flat belt to transmit 12 kw 450 rpm for an engine to a shaft running at 1200 rpm the dia
of engine pulley is 600 mm centre distance is 2 m given
P = 12kw
CD = 2m
D 600
i= =d=
d 2.667
d = 225 mm
2. Calculation of belt speed
dn x600x450x10 -3
V = = = 14.137 m/s
60 60
3. Arc of Contact
D-d
Arc of Contact Q = 180 o - x60 o
C
600-225
o
Arc of Contact Q = 180 - x60 o
C
4. Selecting high speed belt load rating of belt at 180 o and 10 m/s
14.137 168.75
= 0.023 x x
10 180
= 0.0304 kw/mm/ply
kc = 1.04
= 11.538 / 0.1525
= 76 + 13 = 89 mm
(D-d) 2
L = 2c + (D+d)+
2 4c
(1600-225)2
L= 2 x 2000 + (600+225)+
2 4 x2000
L = 5.313 x 103 mm
To give Initial tension to the belt the length is reduced by one percentage
= 53.13 mm
= 5.2598 m
Specification
No of plies = 5
Pulley width = 89 mm
Pulley Design
Driver pulley 3
= 2.94 (89 x 600)/(4x6)
= 38.38 mm
b = 2.94 aD / 4n3
= 31.68 mm
= 25.58 mm
= 21.12 mm
r = (3 / 4) x 38.38
r = (3 / 4) x 31.68
l = 2/3 x a
= (2 / 3) x 89
= 59.333 mm
= 15.515 (driver)
Problem 5
A Stone crushing machine receives power from motor rated at 50 kw at 1800 rpm by
means of a flat belt pulley dia are 200 mm and 700 mm distance between pulley is 4 m
design the belt drive the direction or rotation of 2 pulley opposite to each other.
Given
P = 50 kw
C.D. = 4m
D = 700 mm
d = 200 mm
n = 1800 rpm
dn x200x1800x10 -3
V = = = 18.849 m/s
60 60
3. Arc of Contact
D-d
o
Arc of Contact Q = 180 - x60 o
C
n
i= = 3.5
N
7.54
3.5
700–200
x60 o
o
Q = 180 - 4000
4. Selecting high speed belt load rating of belt at 180 o and 10 m/s
= 0.023 kw / mm / ply
18.849 172.5
= 0.023 x x
10 180
= 0.0415 kw/mm/ply
v-belts are used with electric motors to drive blowers, compressors, appliances (like
mixer, grinder, etc.0, machine tools (like lathe, drilling machine, etc), farm and industrial
machinery, and so on. V-belts are endless and run in grooved pulleys.
V-belts are made in trapezoidal section. The power is transmitted by the wedging action
between the belt and the V-groove in the pulley or sheave.
MATERIALS OF V-BELTS
V-belts are made of cotton fabric and cords moulded in rubber and covered with fabric
and rubber.
ADVANTAGES
According to Bureau of Indian standards (IS :2494-1974), the V-belts are classified as
A,B,C,D and Etype (based on the cross-section of V-belts ).
SPECIFICATIONS OF V-BELTS
V-belts are designated by its type and nominal inside length. For example, a C2845 belts
has a cross-section of type C and has a nominal inside length of 2845mm.
Design procedure:
Select small pulley diameter(d) from the data book . Then using the speed ratio, calculate
the pulley diameter (D). These pulley pulley diameters should be rounded off to a standard
diameter. (Refer data book page no: 7.58).
Select the centre distance, if not given, from the data book. (Refer data book page no:
7.61).
L= 2C + (π / 2) (D+d) + (D+d)2 / 4C
In order to calculate the design power, the following modification factors have to
determined.
For calculated the arc of contact, select the correction factor from the data
book. consulting the data book page no 7.68
Calculate the maximum power capacity (in kw) of a V – belt using the formulas
given the data book page no 7.62.
where
P = Drive power in Kw
Kw = Rated power
B = (D-d)2/ 8
PROBLEM – 1:
Given data:
P= 7.5 kW
N1 =1440 rpm
N2 = 400 rpm
d = 300 mm = 0.3 m
C = 1000mm = 1m.
To Find:
Solution :
Consulting the data book page no 7.58 for power 7.5 kW, B section is
selected.
= 2×1000+( π/2)(1250+315)+(1250-315)2/4×1000
= 4676.85 mm.
For this nominal inside length and Bsection, consulting the data book and then take
the nominal pitch length is selected as 4615mm.
= 123.9°
For this arc of contact, consulting the data book page no 7.68, correction factor
for arc of contact is selected as Fd = 0.83.
Service factor(Fd):
Consulting the data book page no 7.69, for lightduty 16 hours continuous service,
for driving machinesof typeII, service factor is selected as Fa = 1.3.
Consulting the data book page no 7.62 for B section, power capacity formula is
given as
de = dp×fb = 315×1.14=359.1mm.
But from the data book page no 7.62 maximum value of d e in the formula should be 175mm.
= 5.445Kw.
= 1.892 ŧ≈ 2 belts.
Cactual = A+ √A2 – B
A = L/4 – π ( D+ d/ 8)
= 539.17
B = (D-d)2 / 8
= (1250 – 315)2/ 8
= 109278.
= 965.11 mm.
EXERCISE – 1
The centre distance between the motor shaft and the pump shaft is 1200mm. suggest a suitable
multiple V- belt drive for this application. Also calculate the actual belt tensions and stess
induced.
PROBLEM- 2
A V- Belt having a lap of 180°has a cross section area of 2.5 cm2 and groove angle as
45°. The density of a belt is 0.0015 kg/cm3and maximum stress is limited to 400×104 N/ m2. If µ
= 0.15, find the power that can be transmitted, if the wheel has a mean diameter of 300 mm and
runs at 1000 rpm.
GIVEN DATA:
TO FIND;
SOLUTION :
ν = π d N /60
= π × 0.3 × 1000 / 60
= 15.71 m /s.
= 3.426
T1 = 3.426 T2
= 0.0015×106 × 2.5 × 10 -4 × 1
= 0.375 kg/m.
Centrifugal tension , Tc = mν 2
Tc = 0.375 (15.71)2
= 92.65N.
= 400×104×2.5× 10 -4
= 1000 N
T= T1+ TC
T1= T- TC
= 1000- 92.55
= 907.5 N
T2 = T1 /3.426
= 907.5/3.426
= 264.9 N
= (907.5-264.9)×15.71
=10.1 Kw.
Exercise- 2:
Two shafts whose centres are 1m apart are connected by a V- belt drive. The driving pulley
is supplied with 100 kw and has an effective diameter of 300mm. It runs at 1000rpm. While the
driven pulley runs at 375 rpm . the angle of groove on the pulleys is 40° . The permissible
tension in 400mm2 cross sectional area of belt is 2.1 Mpa. The density of the belt is 1100 kg /
m3. Taking µ= 0.28, estimate the number of belts required.
Design procedure :
1. Select the cross section of the belt depending on the power to be transmitted by
consulting data book page no 7.58.
2. For the selected cross- section of the belt, consulting the data book page no
7.70.,select the various required dimensions of the V- grooved pulley.
PROBLEM- 3
GIVEN DATA:
P= 14.7 kW
TO FIND:
SOLUTION:
For the cross section C, Consulting the data book page no 7.70 the various
dimensions of V-grooved pulley are given as below.
Pitch width lp = 19 mm
= 365.5mm.
3. Material selection:
Since the cast iron is economical, stable and durable, we can choose cast iron as a
material for V- grooved pulley.
Wire ropes are used whenever large power is to be transmitted over long distances (upto 150
m).The wire ropes are extensively used in elevators, oil well drilling, mine hoists, cranes,
hauling devices, conveyors, tramways, suspension bridges and other material handling
equipments.
For example, a 6 × 7 rope means a rope made from six strands with seven
wires in each strand.
First select the suitable type of wire rope for the given application
Calculate the design load by assuming a larger factor of safety, say 15 (data
book page no : 9.1) Design load = load to be lifted × Assumed factor of safety.
Select the wire rope diameter (d) from the data book page no 9.5 & 9.6
Consulting the data book page no 9.1, obtain the diameter of sheave. Always
larger sheave diameter is preferred.
Consulting the data book page no 9.1 select the area of useful cross section of
the rope .
dw = d/ 1.5√i
where
Obtain the rope weight (Wr) from the data book page
i. Direct load, Wd = W+ Wr
= (Er × dw) / D ×A
Wa = ( W+Wr / g) × a
Where a = ν1 – ν2 / t
Wea = Wd + Wb+Wa
Breaking load taken from the data book page no 9.5& 9.6 .
PROBLEM – 4:
Design a wire rope for an elevator in a building 60 m height and for a total load of 20
KN. The speed of the elevator is 4 m/ sec and the full speed is reached in 10 seconds.
GIVEN DATA:
t = 10 sec.
TO FIND :
SOLUTION:
= 20 × 15 = 300 kN.
d = 25mm for σu= 1600 to 1750 N/ mm2 and breaking strength = 340 kN.
= 40× 25
= 1000mm.
A= 0.4 d2
= 0.4 × (25)2
= 250mm2
= 6× 19
= 114
dw = 25 / 1.5√114
= 1.56mm
= 23.6 N/ m
= 1416N
= 20000 + 1416
= 21416 N.
Bending load , Wb = σb × A
= Er × dw / D ×A
a = (ν2 –ν1 )/ t1
= 4-0/ 10
= 0.4 m/s2 .
= 873.23 N
= 2 ( 20000 +1416)
= 42832 N.
= 21416+ 32760
= 54176 N
Wea = Wd + Wb+Wa
= 55049.23N
= 32760 + 42832
= 75592 N
From the data book page no 9.1 ,for hoists and class 4, the
recommended factor of safety = 6.
Since the working factor of safety is greater than the recommended factor of
safety, so design is safe.
z2 = i z1
Recommended value of z2 : z2 max = 100 to 120 … [from data book, page no. 7.74]
Now check whether the calculated z2 is less than the recommended z2 max. Because, when
z2 is large, the stretched chain may slip off the sprocket for a small pull.
a = (30 – 50) p
From the pitch range obtained, consulting from data book, page no. 7.74
PT = Pt + Pc + Ps
1020 N
Pt
v
z1 p N 1 z p N2
v = Chain velocity in m / s or 2
60 1000 60 1000
Pc = mv²
Where m = Mass of chain / metre, from data book page nos. 7.71, 7.72
and 7.73.
Ps = k .w.a
Service factor, ks = k1 . k2 . k3 . k4 . k5 . k6
Select the values of k1, k2, k3, k4, k5, and k6 from data book nos. 7.76 and 7.77
Design load = PT x ks
Breaking load Q obtained from data book page nos. 7.71, 7.72 and 7.73
Factor of safety = -------------------------------------------------------------------------------------
Design load
Q
= -----------
PT x ks
If the working factor of safety (FS w) is greater than the recommended minimum
value of factor of safety (n’), then the design is safe and satisfactory.
If the working factor of safety is not satisfactory, one more chain may be added
(i.e., simplex to duplex or duplex to triplex) to the existing one or the chain pitch may be
increased.
Take the bearing area (A) value from data book page nos 7.71, 7.72 and 7.73
e e 2 8M
Exact centre distance, a p
4
z z2
Where e l p 1
2
2
z z1
And M 2 = constant [from data book, page no. 7.75]
2
p
Pcd of larger sprocket, d 2
sin 180 / z 2
Where dr = Diameter of roller taken from data book page nos. 7.71, 7.72 and 7.73.
PROBLEM 5
A truck equipped with a 9.5 kW engine uses a roller chain as the final drive to the rear
axle. The driving sprocket runs at 900 r.p.m and the driven sprocket at 400 r.p.m. with a
centre distance of approximately 600mm. Select the roller chain.
☺ Solution:
(Since the transmission ratio can be calculated from the given data, therefore we need not
to consult data book, page no. 7.74)
z2 = 61 is satisfactory.
a 600
Maximum pitch, pmax = 20 mm
30 30
a 600
and Minimum pitch, pmin = 12 mm
50 50
any standard pitch between 12 mm and 20 mm can be chosen. But to get a quicker
solution, it is always preferred to take the standard pitch closer to pmax. Refer data book
page no. 7.74
z1 p N 1 27 15.875 900
6.43m / s
60 1000 60 1000
m = 1.78 kg/m
k = 6 (for horizontal)
ks = k1 . k2 . k3 . k4 . k5 . k6
From data book page no. 7.76 k1 = 1.25 (for load with mild shocks)
From data book page no. 7.76. k3 = 1 ( we have used ap = (30 to 50) p)
From data book page no. 7.77 k6 = 1.25 (for 16 hours / day running)
Where A = 140 mm² from data book page nos. 7.71, 7.72 and 7.73.
1507 1.5625
= 16.8 N/mm²
140
Consulting data book page no. 7.77, for smaller sprocket speed of 900 r.p.m. and pitch
15.875 mm, the allowable bearing stress is 22.4 N/mm². Therefore the induced stress is
less than the allowed bearing stress. Thus the design is safe and satisfactory.
27 61 61 27 / 2
2
lp = 2 (37.795) + 120.36
2 37.795
z z2 27 61
Where e = lp - 1 122 78
2 2
2 2
z z1 61 27
and M= 2 29.28
2 2
78 78 2 8 29.28
a= 15.875 6.1311 mm
4
Decrement in centre distance for an initial sag = 0.01a = 0.01 (613.11) = 6.1311 mm
p
Ped of smaller sprocket, d1 = 136.74 mm
sin 180 / 27
Where dr = Diameter of roller, from data book page nos. 7.71, 7.72 and 7.73. =
10.16 mm
Larger sprocket:
p 15.875
Ped of larger sprocket, d2 = = 308.38 mm
sin 180 / z 2 sin 180 / 61
PART – B
1. A flat belt drive is to design to drive a flour mill. The driving power requirements of the mill
are 22.5 KW at 750 rpm with a speed reduction of 3.0. The distance between the shafts is 3m.
Diameter of the mill pulley is 1.2 m. Design and makes a neat sketch of the drive. (16)
(M/J 2012)
2. Design a chain drive to drive a centrifugal compressor from an electric motor 15 KW at 1000
rpm. The speed reduction ratio required is 2.5. The compressor to work for 16 hours a day.
State solutions for common problems encountered in continuous operation of the drive.
(16) (M/J 2012)
3. Design a V-belt drive to transmit 50 KW at 1440 rpm from an electric motor to a textile
machine running 24 hours a day. The speed of the machine shaft is 480 rpm.
(16) (A/M 2008)
4. A crane is lifting a load of 18 KN through a wire rope and hook. The weight of the hook etc.
is 10 KN. The load is to be lifted with an acceleration of 1m/sec2. Calculate the diameter of
the wire rope. The rope diameter may be taken as 30 times the diameter of the rope. Take a
factor of safety of 6 on a young’s modulus for the wire rope 0.8 × 105 N/mm2. The ultimate
stress may be taken as 1800 N/mm2. The cross-sectional area of the wire rope may be taken
as 0.38 times the square of the wire rope diameter. (16) (N/D 2007)
2
5. a) A V-belt having a lap of 180˚ has a cross section area of 2.5 cm and groove angle as 45˚.
The density of a belt is 0.0015 Kg/cm3 and maximum stress is limited to 400 104 N/m2. If
µ=0.15. Find the power that can be transmitted, if the wheel has a mean diameter of 300 mm
and runs at 1000 rpm. (08)
b) Power is transmitted between two shafts by a V-belt whose mass is 0.9 Kg/m length. The
maximum permissible tension in the belt is limited to 2.2 KN. The angle of lap is 170˚ and
the groove angle 45˚. If the coefficient of friction between the belt and pulleys is 0.17, find
6. a) Find the width of the belt necessary to transmit 7.5 KW to a pulley of 300mm diameter, if
the pulley makes 1600 rpm and the coefficient of friction between the belt and the pulley is
0.22. Assume the angle of contact as 210 and the maximum tension in the belt is not
exceeding 8 N/mm width. (08)
b) A leather belt 125 mm wide and 6 mm thick, transmits power from a pulley with the angle
of lap 150˚ and µ=0.3. If the mass of 1m3 of leather is 1 Mg and the stress in the belt is not to
exceed 2.75 Mpa. Find the maximum power that can be transmitted and the corresponding
speed of the belt. (08) (A/M 2011)
7. Design a flat belt drive to transmit 110 KW for a system consisting of two pulleys of
diameters 0.9m and 1.2m respectively, for a Centre distance of 3.6m, belt speed of 20m/s and
coefficient of friction = 0.3. There is a slip of 1.2% at each pulley and 5% friction loss at
each shaft with 20% over load. (16) (N/D 2009)
8. Design a chain drive to transmit 6 KW at 900 rpm of a sprocket pinion. Speed reduction is
2:5:1. Driving motor is mounted on an adjustable base. Assume that load is steady, drive is
horizontal and service is 16 hours/day. (16) (A/M 2010)
9. Design a flat belt drive to transmit 6 KW at 900 rpm of the driver pulley. Speed reduction is
to be 2:5:1. Assume that the service is 16 hours a day. (16) (A/M 2010)
10. A truck equipped with a 9.5 KW engine uses a roller chain as the final drive to the rear axle.
The driving sprocket runs at 900 rpm and the driven sprocket at 400 rpm with a Centre
distance of approximately 600 mm. select the roller chain. (16) (A/M 2011)
Reference books:
1. Machine design (volume –II), Design of Transmission Systems, S.Md.Jalaludeen
2. Machine design – R.S. Khurmi & J.K. Gupta
3. Design of transmission systems – T.J. Prabhu
4. Design of transmission systems – V. Jayakumar