199-CRR

HY TR O L
Chain Driven Live Roller Conveyor
The Model 199-CRR is a medium-duty chain driven • 11 Bed Widths
live roller conveyor. The roll-to-roll chain drive • Center Drive
Conveyor shown with
makes this conveyor ideal for light to medium duty • Reversible optional floor supports

CO N V E Y O R
pallet handling or oily conditions which are not • Chain Driven Rollers
suitable for belt driven live roller.
• Adjustable MSN-Type Floor Supports Available

Conveying
12 1/4" 14 1/4" 16 1/4" 18 1/4" 20 1/4" 22 1/4" 24 1/4" 28 1/4" 30 1/4" 34 1/4" 36 1/4"
Surface

CO M P A N Y ,
Between
15" 17" 19" 21" 23" 25" 27" 31" 33" 37" 39"
Rail Width
Overall
18" 20" 22" 24" 26" 28" 30" 34" 36" 40" 42"
Frame Width
Base
655 680 705 730 755 780 805 855 880 930 955
Weight
Weight (Lbs.) Per Foot
51 53 55 57 59 61 63 67 69 72 75
4" Roller Centers

I N C.
Weight (Lbs.) Per Foot
46 47 49 51 52 54 55 59 60 63 65
6" Roller Centers

OVERALL LENGTH
18" "X"
FLOW

1-3/4"

9-13/16" "X"

OPTIONAL MSN
SUPPORTS SHOWN

14-7/16" 7-3/16" ALLOW 16"

4-3/16"

OVERALL FRAME
WIDTH
BETWEEN RAIL 2-3/4"
WIDTH
CONVEYING
SURFACE
1/4" 1-5/32" 13/16"

3-1/2" 4-3/4"

16-15/16"
13-3/16"

SECTION X-X

7.1
HYTROL CONVEYOR CATALOG
01012017
I N C.
• STANDARD SPECIFICATIONS 199-CRR
BED–Roller bed with 1.9 in. x 9 ga. wall unplated tread rollers spaced every 4 in. or 6 in. mounted SPEED REDUCTION–Sealed worm gear C-Face speed reducer.
in 7 ga. powder painted formed steel channel frame bolted together with butt couplings.
MOTOR–1/2 HP–208/230/460/575V–3 Ph. 60 Hz. Totally Enclosed C-Face.
CENTER DRIVE–Mounted underneath bed section.
CO M P A N Y ,

CONVEYING SPEED–Constant 35 FPM.

ROLLER CHAIN–No. 40 roller-to-roller chain.
CAPACITY–Maximum load per linear foot of conveyor 150 lbs. with supports on 10 ft. centers,
MOTOR DRIVE CHAIN–No. 60 chain. 250 lbs. per ft. with supports on 5 ft. centers and 4 in. roller centers. NOT TO EXCEED capacity in
charts.
CHAIN GUARD–Mounted to top of channel frame to totally enclose drive chain.
FLOOR SUPPORTS–Now supplied as optional equipment.
BEARINGS–Sealed, pre-lubricated ball bearings on drive roller shaft.
CO N V E Y O R

LOAD CAPACITY CHART @ 35 FPM & 6" ROLLER CENTERS

HY TR O L

OVERALL WIDTH 18" - 28" 30" - 42"

OVERALL LENGTH 25' 50' 25' 50'
SUPPORT CENTERS 5' 10' 5' 10' 5' 10' 5' 10'
1/2 2250 2250 1250 1250 2000 2000 1000 1000
HP 1 5000 3750 3250 3250 5000 3750 3000 3000
2 6250 3750 7250 7250 6250 3750 7000 7000

CHAIN GUARD REMOVED TO ILLUSTRATE ROLL TO ROLL DRIVE CHAIN.

WARNING: DO NOT OPERATE CONVEYOR WITH CHAIN GUARD REMOVED.

• OPTIONAL EQUIPMENT

FLOOR SUPPORTS–MSN Type floor supports are available with a wide range of adjustment. Specify
top of belt or roller elevation. One support required at every bed joint and ends of conveyor. Holes in CHAIN CROSSOVER–Move driving chain from one side to opposite side.
feet for lagging to floor. Knee braces recommended above MSN-6 support.
GUARD RAILS–Adjustable Universal Channel Guard Rail, (both sides) fixed channel (both sides) or
CONVEYING SPEED–Other constant and variable speeds. NOTE: Capacity affected with speed angle (one side). See Accessory section .
change.
POLY-TIER SUPPORTS–36 in. to 120 in. support heights in 6 in. increments. Knee braces supplied.
SHAFT MOUNTED DRIVE–Requires shaft mounted gearmotor. Minimum elevation top of rollers
6 in. CEILING HANGERS–5/8 in. dia. x 8 ft. long unplated rods fully threaded. Other lengths and galvanized
rods available.
O-RING DRIVE CHAIN–With sealed in lubricant (Recommended for applications that do not permit
regular lubrication). MOTORS–Energy efficient, single phase, brakemotor. 2 HP maximum.

ROLLERS SET LOW–Tread rollers mounted in 4 3/4 in. x 10 ga. formed steel channel frame to form ELECTRICAL CONTROLS–Non-reversing magnetic starters and
1 in. high guard rails. push-button stations. AC variable frequency drive.

7.2
HYTROL CONVEYOR CATALOG
01012017