UniOP Cables - Manufacturer List

Producer Model Cable Type Note

Allen Bradley
1747 KE DF1 Module
CA012 RS 232
Device Net
CA150 CAN Compatible only with panels of type –0045 using TCM03.To connect one or more
panels to the DeviceNet network refer to the available DeviceNet documentation on
Transmission Media Requirements.DeviceNet requires a terminating resistor to be
installed at each end of the network trunk. The resistor requirements are: 121 ohm,
1% metal film, ¼ Watt.Terminating resistor should not be installed at the end of a
drop line, only at the two ends of the trunk line.External network power supply (+24
Vcc) is necessary. Refer to DeviceNet documentation for more details.
Micrologix
CA095 RS 232
PLC 5
CA007 RS 232 Generic DTE DB25P RS-232
SLC 5/03
CA012 RS 232
SLC 5/04
CA012 RS 232
SLC 500
CA025 RS 485
SLC 500 AIC Module
CA026 RS 485
CA029 RS 485 Connector to the A-B DH485 network
Altus
AL 2000
CA124 RS 232
CA125 RS 232
Compumotor
Zeta Drive
CA122 RS 232
Control Techniques
Dinverter A
CA131 RS 485
Dinverter B
CA127 RS 422
Unidrive
CA081 RS 232
Unidrive & Quantum III
CA116 RS 422
Crouzet
RPX10
CA129 RS 232
RPX30
CA129 RS 232
CTC

CA226 RS 232 PLC Port to CT Unidrive

CTC Controller
CA157 RS 232

giovedì 6 maggio 2004 Page 1 of 10

Producer Model Cable Type Note
Danfoss
VLT5000
CA167 RS 485
Delta Tau
PMAC
CA172 RS 232 Connect to J5 connector
D-Tech
David 0.5 C1
CA096 RS 485 Can be used to connect old panel models type –0044 (TCA06 interface) to S7-
300/400
Eagle Signal
Eagle Modbus Adapter
CA081 RS 232
Eberte
PLS514 & K43
CA109 RS 232 Connects directly to K43
CA110 Current To be used only with the NEW type of Current Loop interface (-0042). Connects
directly to K43.
Entrelec
S200
CA196 RS 232 Cable to be 6 inches long - used as an adaptor cable
Festo
FC com
CA233 RS 232
FEC
CA147 RS 232
FPC 101
CA053 RS 232 connects to diagnostic port on front panel
FPC 405
CA055 RS 232
IPC
CA012 RS 232
SB 202
CA054 RS 232
SF3
CA054 RS 232
Galil
DMC 1500
CA081 RS 232
GE Fanuc
CMM Port 1
CA091 RS 232
CMM Port 2
CA090 RS 422 (A=-) (B=+)
CA091 RS 232
IC690ACC900 Converted
CA014 RS 232
Micro PLC
CA056 RS 232
Series 1 DCU
CA007 RS 232 Generic DTE DB25P RS-232

giovedì 6 maggio 2004 Page 2 of 10

Producer Model Cable Type Note
Series 90 Programming port
CA010 RS 422 GE 90 Prog. Port
VersaMax
CA081 RS 232
CA210 RS 422
GFR
ecs 3+
CA231 RS 485
Groundfos
Controll Unit CU 3
CA230 RS 485
Hitachi
EC Series
CA062 RS 232
EH-150
CA155 RS 232
CA221 RS 485
EH-Micro
CA155 RS 232
CA185 RS 422
CA195 RS 485
EM II
CA052 RS 232
H Series
CA051 RS 232
H-252C
CA132 RS 232 Operation is set at the speed of 19200 bauds (PHL=1)
J300
CA163 RS 232
CA164 RS 485
L100
CA190 RS 422
L300P
CA205 RS 485
SJ100
CA190 RS 422
SJ300
CA205 RS 485
Honeywell
620 LCS
CA168 RS 422 Connection using the Modbus RTU protocol
Idec Izumi
FA Series
CA050 RS 232
Micro 1
CA100 RS 232 Maximum cable length is 2 meters
Micro 3
CA076 RS 485
Micro 3C
CA159 RS 485

giovedì 6 maggio 2004 Page 3 of 10

Producer Model Cable Type Note
Micro 3C & TSX07 Schneider
CA138 RS 232
PF2-CLA Link Adapter
CA048 RS 232
PF3S-S1F2 Module
CA012 RS 232
Ifm Electronic
AS/I Controller
CA012 RS 232
AS-I ControllerE
CA223 RS 232 per AS-I ControllerE order no. AC1304
Intelligent Actuator
XSEL controller
CA232 RS 232
Intramat
DKC
CA209 RS 485
IPM
IP1612L
CA112 RS 232
Jetter
NANO B
CA206 RS 232
CA207 RS 422
CA208 RS 232
Keyence
Keyence KV-L2
CA061 RS 232
Koyo
DL 205 Series
CA071 RS 232
DL 305 Series
CA016 RS 232
DL 405 Series
CA007 RS 232 Generic DTE DB25P RS-232
CA008 RS 232 TI425/435 or Koyo DL405 Prog. Port
CA009 RS 422 TI435 or Koyo DL405 Network Port
Matsushita
FP0
CA099 RS 232 DO NOT connect pin #5 of the PLC connector as this pin has 5V on it.
FP1
CA015 RS 422
CA044 RS 232 Compatible with: Matsushita FP1, Omron C20H
FP10SH
CA044 RS 232 Compatible with: Matsushita FP1, Omron C20H
FP2
CA044 RS 232 Compatible with: Matsushita FP1, Omron C20H
CA099 RS 232 DO NOT connect pin #5 of the PLC connector as this pin has 5V on it.
FP3
CA046 RS 422
FP5

giovedì 6 maggio 2004 Page 4 of 10

Producer Model Cable Type Note
CA046 RS 422
FPM
CA099 RS 232 DO NOT connect pin #5 of the PLC connector as this pin has 5V on it.
Mitsubishi
A Series
CA066 RS 232 puo` essere usato anche come interfaccia RS 422
FX
CA031 RS 422
FX0
CA030 RS 422
FX0N
CA030 RS 422
FX0S
CA030 RS 422
FX2N
CA030 RS 422
CA216 RS 485
Melsec R2 Module
CA032 RS 232 Use with A1SJ71C24-R2 module for point to point connection. Refer to TN49 for
more information.
Modicom Modbus
Modbus Micro
CA076 RS 485
Modbus Multiplexer
CA098 RS 232
Modbus port
CA007 RS 232 Generic DTE DB25P RS-232
CA011 RS 232
Möeller
DV5 / DF5 Inverter (Hitachi SJ100)
CA190 RS 422
DV6 / DF6 Inverter (Hitachi SJ300)
CA205 RS 485
Easy
CA218 RS 232 Adapter cable - Original programming cable of device required (Moleer Easy)
Flex +
CA055 RS 232
PS306
CA063 RS 485
PS316
CA064 RS 485
CA137 RS 485 Use only with operator panels with product suffix -xx45.The usage of shielded
connectors is recommended.
PS4-100
CA105 RS 485 Use only with operator panels with product suffix -xx45
PS4-150
CA092 RS 232 8 pin Circular DIN plug (DIN 41524 - Hirschmann MAWI 80 SB)
PS416
CA055 RS 232
CA064 RS 485

giovedì 6 maggio 2004 Page 5 of 10

Producer Model Cable Type Note
CA137 RS 485 Use only with operator panels with product suffix -xx45.The usage of shielded
connectors is recommended.
PS4-200
CA092 RS 232 8 pin Circular DIN plug (DIN 41524 - Hirschmann MAWI 80 SB)
CA105 RS 485 Use only with operator panels with product suffix -xx45
Smart Move
CA012 RS 232
Suconet K (DIN Conn.)
CA120 RS-485
Mycom
MAC300
CA081 RS 232
Omron
C Series
CA007 RS 232 Generic DTE DB25P RS-232
CA065 RS 422
C200H
CA058 RS 232
C200HS
CA058 RS 232
C20H
CA044 RS 232 Compatible with: Matsushita FP1, Omron C20H
C60H
CA044 RS 232 Compatible with: Matsushita FP1, Omron C20H
CJ
CA222 RS-232
CPM1
CA058 RS 232
CA126 RS 422
CQM Series
CA058 RS 232
CS1
CA058 RS 232
CV Series
CA058 RS 232
CA078 RS 422
Parker
Compax-S
CA055 RS 232
CA213 RS 485
EASI Controller
CA224 RS 485
CA225 RS 232
sLVD1
CA229 RS 422
Philips
P8
CA107 RS 422
PC20
CA091 RS 232
QEM

giovedì 6 maggio 2004 Page 6 of 10

Producer Model Cable Type Note
Qmove
CA220 RS 422 User Port on Q1 CPU required +12 Vdc to work
Saia
PCD (all cpu)
CA182 RS 232 - Adapter PLC port to SAIA programming cable
PCD1
CA142 RS 232 SAIA PCD1 – PGU Port
PCD2
CA043 RS 232 If the PCD at the moment of the start-up recognizes that the cable is connected and
UniOP running (control lines active), it will assume that the programming package is
connected and the PCD will start in STOP mode, even if a valid PLC program is
loaded. In all normal conditions (PCD and UniOP powered by the same source)
proper operation will be however assured since the PLC is always faster than the
UniOP to start-up (the PLC program will be running before UniOP goes to operation
mode).
CA176 RS 485 SAIA PCD-2 (S-BUS)
CA177 RS 422 SAIA PCD-2 (S-BUS)
CA178 RS 232 SAIA PCD 7 F120 Module
CA179 RS 232 SAIA PCD2 F520 Module
CA180 RS 485 SAIA PCD7 F110 Module
CA181 RS 485 SAIA PCD 2 F520 Module
PCD4
CA043 RS 232 If the PCD at the moment of the start-up recognizes that the cable is connected and
UniOP running (control lines active), it will assume that the programming package is
connected and the PCD will start in STOP mode, even if a valid PLC program is
loaded. In all normal conditions (PCD and UniOP powered by the same source)
proper operation will be however assured since the PLC is always faster than the
UniOP to start-up (the PLC program will be running before UniOP goes to operation
mode).
PCD6
CA043 RS 232 If the PCD at the moment of the start-up recognizes that the cable is connected and
UniOP running (control lines active), it will assume that the programming package is
connected and the PCD will start in STOP mode, even if a valid PLC program is
loaded. In all normal conditions (PCD and UniOP powered by the same source)
proper operation will be however assured since the PLC is always faster than the
UniOP to start-up (the PLC program will be running before UniOP goes to operation
mode).
Schneider Automation
AEG A120 TSX Compact
CA055 RS 232
AEG A120 TSX Micro
CA077 RS 232
MOMENTUM
CA214 RS 422
TSX07 Nano
CA076 RS 485
TSX17
CA072 RS 485
CA094 RS 485
TSX37 Micro
CA076 RS 485
TSX47
CA103 RS 232 This cable includes an RS-232 to Current Loop converter. The Current Loop interface
is passive.
TSX57 Premium
CA076 RS 485

giovedì 6 maggio 2004 Page 7 of 10

Producer Model Cable Type Note
Uni-Telway
CA102 RS 485
SEW Eurodrive
Movidrive
CA081 RS 232
CA169 RS 485
Movidyn
CA141 RS 485 Connects to Movidyn MPB…/MPR… through X02 and to Movidyn MKS51A through
X41
Movitrac
CA141 RS 485 Connects to Movidyn MPB…/MPR… through X02 and to Movidyn MKS51A through
X41
CA160 RS 485
Siemens
SIMATIC S5
CA097 Current To be used only with the NEW type of Current Loop interface (-0042)
SIMATIC S5 CP 524
CA153 RS 422
SIMATIC S5 CP 524/525
CA023 RS 232
SIMATIC S7 200
CA096 RS 485 Can be used to connect old panel models type –0044 (TCA06 interface) to S7-
300/400
Simatic S7 300
CA128 RS 485 Compatible only with panels of type -0045 using TCM01 or TCM07. Use only for point-
to-point connection in MPI
systems.The Bus Connector 6ES7972-0BB20-0XA0 can be used for the PLC
connector in order to provide the additional connection to the programming unit.The
use of shielded connectors is recommended.
SIMATIC TI 305-03
CA007 RS 232 Generic DTE DB25P RS-232
SIMATIC TI 335
CA016 RS 232
SIMATIC TI 405 Series
CA008 RS 232 TI425/435 or Koyo DL405 Prog. Port
SIMATIC TI 435
CA007 RS 232 Generic DTE DB25P RS-232
CA009 RS 422 TI435 or Koyo DL405 Network Port
SIMATIC TI 505
CA012 RS 232
SIMATIC TI 545 CPU 1101
CA042 RS 422
SIMATIC TI 545 CPU 1103
CA104 RS 422
CA121 RS 232
SIMATIC TI 555
CA022 RS 422
Square D
SY/MAX 50
CA050 RS 232
Taian
TP02
CA186 RS 422 Connection using the Computer Link Protocol

giovedì 6 maggio 2004 Page 8 of 10

Producer Model Cable Type Note
CA187 RS 485 Follow instructions for corrent earth connection of the PLC in TAIAN TP02 Series
User's Manual
Toshiba
EX100
CA088 Current To be used only with the NEW type of Current Loop interface (-0042).Compatible with
M20, M40, EX-100 and EX-250.
EX250
CA088 Current To be used only with the NEW type of Current Loop interface (-0042).Compatible with
M20, M40, EX-100 and EX-250.
M20
CA088 Current To be used only with the NEW type of Current Loop interface (-0042).Compatible with
M20, M40, EX-100 and EX-250.
M40
CA088 Current To be used only with the NEW type of Current Loop interface (-0042).Compatible with
M20, M40, EX-100 and EX-250.
T1
CA106 RS 232
T2
CA012 RS 232
UniOP
Adapter
CA038 RS-232
Alfa Panel
CA119 RS 232
ePALM10-0067
CA234 RS 232
PLC Port to DCE DE9P (Adapter)
CA038 RS 232 Can be used as an adapter between the PLC port of the panel and a copmmunication
cable designed for a 9 pin PC COM port.
SXP-320/325 Serial/Parallel Converter
CA215 RS 232 UniOP Printer Port to DCE Serial to Parallel Converter
TCA11 Adapter
CA227 RS 485 TCA11 adapter PLC/Port RS-485 / RS-422 Only
CA228 RS 232 TCA11 Adapter per CA2, CA114 and CA193
TSI01 - PC port
CA074 RS-232
TSI01 - PLc port
CA073 RS 232 This cable is intended for use with the UniNET network
TSI02 - Plc port
CA075 RS-485
W&D Progr. Port of MD21 & MD23
CA219 RS 232 Programming cable for special model MD21 & MD23 of Winkler & Dünnebier
WCE Programming Port to AT
CA193 RS 232
Wago
Modbus Programmable fieldbus controller
CA235 RS 422
Warner Electric
SLO-SYN 2000 Series
CA081 RS 232
WestingHouse
PC50
CA005 Current Max cable length 60m. Use only with panels 0020

giovedì 6 maggio 2004 Page 9 of 10

Producer Model Cable Type Note
PC500
CA005 Current Max cable length 60m. Use only with panels 0020
PC55
CA005 Current Max cable length 60m. Use only with panels 0020
Yaskawa
fdfdsfdsf
CA223 RS 232 per AS-I ControllerE order no. AC1304
MP940
CA194 RS 422
NS-600 Indexer
CA198 RS 232
Sigma II
CA198 RS 232
Z-World
Little Star
CA139 RS 232

giovedì 6 maggio 2004 Page 10 of 10