PT320AT02-2 Product Spec - Ver 1 0 - 20191128 - HKC
PT320AT02-2 Product Spec - Ver 1 0 - 20191128 - HKC
滁州惠科光电科技有限公司
Ver. 1.0
Date: 28. Nov.2019
( ) Preliminary Specification
( √ ) Approval Specification
Any modification is not allowed without HKC’s permission
Reviewed By PM Date
Name: Asia
Signature:
Contents
Revision History............................................................................................................................. 3
1. GENERAL DESCRIPTION .......................................................................................................... 4
1.1 General Specifications ........................................................................................................ 4
2. ABSOLUTE MAXIMUM RATINGS .............................................................................................. 5
2.1 Absolute Maximun Ratings ................................................................................................. 5
2.2 Absolute Ratings of Environment ........................................................................................ 5
3. ELECTRICAL SPECIFICATIONS ............................................................................................... 6
3.1 Electrical Characteristics..................................................................................................... 6
3.1.1 Power consumption .................................................................................................. 6
3.1.2 LVDS characteristics................................................................................................. 7
3.1.3 LVDS Format ............................................................................................................ 8
3.1.4 Block diagram ........................................................................................................... 8
3.2 Interface Connections ......................................................................................................... 9
3.3 Timing Spec. ..................................................................................................................... 11
3.4 Power On/Off Sequence ................................................................................................... 13
3.5 Flicker Adjustment ............................................................................................................ 14
3.6 Driver IC ESD spec ........................................................................................................... 14
4. OPTICAL CHARACTERISTICS ................................................................................................ 15
4.1 Measurement Conditions .................................................................................................. 15
4.2 Optical Specifications ....................................................................................................... 16
5. MECHANICAL CHARACTERISTICS ........................................................................................ 18
5.1 Mechanical Specification .................................................................................................. 18
5.2 Packing ............................................................................................................................. 19
5.2.1 Packing specifications ............................................................................................ 19
6. DEFINITION OF LABELS ......................................................................................................... 20
6.1 Open Cell Label ................................................................................................................ 20
6.2 Carton Label ..................................................................................................................... 21
6.3 Pallet Label ....................................................................................................................... 22
7. PRECAUTION ........................................................................................................................... 23
7.1 Unpacking ......................................................................................................................... 23
7.2 Storage test ...................................................................................................................... 23
Revision History
1. GENERAL DESCRIPTION
The specification is applied to 31.5” model (PT320AT02-2) TFT Liquid Crystal Display open cell and it supports
1366 x 768 HD mode with 16.7M colors. This product is with driver ICs and a 30-pins-1ch-LVDS circuit board and built
in without backlight unit.
ABC
Scan direction
3. ELECTRICAL SPECIFICATIONS
3.1 Electrical Characteristics
3.1.1 Power consumption
Value
Parameter Symbol Unit Note
Min. Typ. Max.
Note:
(1) Ambient temperature: 25 ± 2ºC
(2) The ripple voltage should be controlled under 10% of VCC
(3) Measurement Conditions: VCC rising time=470μs
VCC
VCC×0.9
VCC×0.1
GND
470μs
(4) Measurement Conditions: Vcc =12V, Ta = 25 ± 2 ºC, Fv = 60 Hz, whereas the test pattern is shown as below.
VTH
VCM |VID|
VTL
GND
DATA
DATA DRIVER
TIMING
VCC
CONTROLLE TFT LCD PANEL
(1366x768)
DC/DC
CONVERTER
Note:
(1) Following finger shows the LVDS pin1 diagram.
#1 #30
CN
#1 #30
CN
Fig 3.7 LVDS connector direction sketch map
(2) For HKC used only, please leave it open.
(3) High: connect to +3.3V→JEIDA Format; Low: connect to GND or Open→VESA Format.
X+C_Board PCBA
1KΩ
SELLVDS TCON
10KΩ
Input connector
TVD TVB
DE
TH
DCLK
TCLK
THB THD
DE
90% 90%
OFF ON OFF
Backlight
Values
Parameters Units
Min. Typ. Max.
T1 0.5 - 10 ms
T2 0 - 50 ms
T3 500 - - ms
T4 100 - - ms
T5 0 - 50 ms
T6 1000 - - ms
Attention:
(1) The supply voltage of the external system for the module input should be the same as the definition.
(2) To avoid some abnormal display noise, we suggest "VCC falling time" to follow "T6" definition.
(3) The product should be always operated within above ranges.
(4) In case of VCC is off level, please keep the level of input signals on the low or keep high impedance.
4. OPTICAL CHARACTERISTICS
4.1 Measurement Conditions
The table below is the test condition of optical measurement.
Item Symbol Value Unit
Light source HKC 31.5” WXGA module White LED Backlight Module/ Film structure
𝑪𝑹𝒘
Contrast Ratio (CR): 𝑪𝑹 =
𝑪𝑹𝑫
CRW : Luminance of LCD module with full screen white pattern (255,255, 255) at center point.
CRD : Luminance of LCD module with full screen Dark pattern (0, 0, 0) at center point.
Where the measure point of to the Contrast Ratio is the center of the panel
Measured Response To
time 0% 25% 50% 75% 100%
0% T0%to25% T0% to 50% T0% to 75% T0% to 100%
25% T25% to 0% T25% to 50% T25% to 75% T25% to 100%
From 50% T50% to 0% T50% to 25% T50% to 75% T50% to 100%
75% T75% to 0% T75% to 25% T75% to 50% T75% to 100%
100% T100% to 0% T100% to 0% T100% to 50% T100% to 75%
Table 4.2 Switching time of luminance ratios matrix
Fig 4.4
5. MECHANICAL CHARACTERISTICS
5.1 Mechanical Specification
5.2 Packing
5.2.1 Packing specifications
Specification
Item
Quantity Dimension (mm) Weight (kg)
Net Weight: 15.6Kg
Packing Box 17pcs/box 857(L) x 577(W) x 105(H)
Gross Weight: 16.4Kg
Pallet 1 1200(L) x 900(W) x 150 (H) Net Weight: 16.5Kg
Stack Layer 9
Pallet after Packing 306pcs/pallet 1200(L) x 900(W) x 1038(H) Gross Weight: 315.96Kg
6. DEFINITION OF LABELS
6.1 Open Cell Label
Model Name
Manufactured Date
Serial
SerialNumber
Number
Panel ID
Manufactured Date: Y M DD
Date: 01~31
Manufactured Date
Panel Size
Cell Quantity
Manufactured Date
7. PRECAUTION
Please pay attention to the followings when a TFT-LCD cell is used, handled and mounted.
7.1 Unpacking
Should use immediately after unpacking TFT-LCD cell to prevent the terminal corrosion.
Protection film for a polarizer on a TFT open cell should be slowly peeled off so that the electrostatic charge can be
minimized.
Source PCB should be connected to the ground when peel off the protection film.
The protection film should not be contacted to the driver during peeling off.