Design of Moment and Shear Connection
Design of Moment and Shear Connection
ASpectrum Designs Plus Engineering Services Project Title: Proposed Two Store Residential Building
Address: 8487 Sandoval Avenue, Pinagbuhatan, Pasig City 1602 Project Location: Villa Cuana Phase 1, Pinagbuhata, Pasig City 1602
Contact: 09982028893 Structural Engineer: Engr. Andro S Rebuyas, RCE, ME-1, RMP, M.Eng-SE
Gmail add: [email protected] Membership: M.PICE, M.ASCE, M.PAMEA, M.FPEA, M.PSUMP, M.NAMPAP, M.SEAD
STAAD Input
Member Forces
M= 185.84 kN-m Moment 252.00 kips-ft
A= 0 kN Axial 0.000 kips
Bottom Plate
BEAM
W24x55 Select Beam
Mu = 252.00 kips-ft (should be anywhere between from 253 - 431 kips-ft) Enter Moment for Design
phiMp = 506 kips-ft Moment Capcity of Beam
0.5*phiMp = 253 kips-ft 50% Moment Capacity
Pu = 0 kips (enter positive only) Enter Beam Axial Force or Zero
d= 23.6 in. Diameter
BOLTS
D2 = 3/4 in. Diameter
A490SC Slip-critical connection Select Bolt Type
n= 4 See below for other SC input Enter Number of Rows
m= 2 Cap = 16.8 k/bolt Number of Columns
N= 8 Number of Bolts
FLANGE PLATES
Top and
W24x55
Bottom Plate
t= 3/4 0.505 in. 12.827 mm Thickness
b= 7 7.01 in. 178.054 mm Width
OVS STD Select Hole Type in Flange Plates: Oversize Round Holes in plates
Dh = 15/16 13/16 in. 20 51/80 mm Hole diameter Standard Round Holes in W24x55
fy = 36 50 ksi 344.75 Mpa Top and Bottom Plates
fu = 58 65 ksi 448.175 Mpa Top and Bottom Plates
Ab = 0.44 in^2 Area of Bolt For Slip Critical Prevent slip at service level
Fnv = 38.05 ksi Bolt Shear Capacity Class A or B? mu = 0.5 Slip coefficient, See J3.8
phi = 1.00 Cap = 16.8 k/bolt Du = 1.13
phi Vnb = 134 k Bolt Capacity = phi*N*Fnv*Ab hsc = 0.85
Vub = 128 k Flange Force = 12Mu/d + Pu/2 Tb = 35
OK Fnv = mu*Du*hsc*Tb*Ns/Ab
Prevent slip at service level does not mean to use service loads
Top and
W24x55
Bottom Plate
24.35 23.10 in. Moment Arm
2 2 in. Min Spacing of Bolts
sheared sheared per Table J3.4 Sheared Edge or Rolled Edge?
1 5/16 1 1/4 in. (includes C2) Min Edge Distance
3 3 in. Actual Spacing of Bolts
1 5/16 1 1/4 in. Actual Edge Distance
0.84 0.84 in. Lc at Edge
2.06 2.19 in. Lc Between Bolts
yes yes Sect J4.10 Is bolt hole deformation important?
44.04 33.24 k Rn Per Bolt for End Bolts
78.30 59.09 k Rn Per Bolt for Other Bolts
Phi = 0.75 0.75 phi
phi Rn = 418 316 k Total Bearing Capacity
Ru = 124 131 k Bearing Force at Center of Plate
OK OK
CHECKING OF TENSION STRESS GROSS SECTION
Top and
W24x55
Bottom Plate Tension Rupture of Tension Flange (U=1)
5.13 5.39 in net width Chapter F13
U= 1.00 1.00 Reduction Coefficient
Ae = 3.84 2.72 in^2 Ae = U*An = U*bn*t FuAfn 176.76 k
phi = 0.75 0.75 Y 1.00 k
phi Pn = 167 431 = phi Mn Capacity = Pcap = phiFuAe YFyAfg 177.00 k-ft
Pu = 124 252 = Mu phi Mn 430.67 k-ft
OK OK
Bottom Plate
Area, A 5.25
K value 0.50
L= 3.00
r = t/(12^.5) = 0.22
KL/r = 6.93
4.71*sqrt(E/fy) = 133.68
Fe = 5962.89 ksi
Fcr = 35.91 ksi OK
phi = 0.90
phi Pn = 170
Compression Length
Pu = 124
OK
RESULT SUMMARY
STAAD Input
Member Forces
V= 186 kN Shear 41.814 kips
BEAM
Vu = 42 kips (should be between from 68 - 135 kips) Enter Shear for Design
SL = 15 ft (if designing to capacity of beam) Span Length
phiMp = 506 kips-ft Moment Capcity of Beam
Vu 1 = 135 kips Vu using 4(phiMp)/L
Vu 2 = 322 kips Vu using phi 0.6Awfy
BOLTS
D2 = 3/4 in. (if different, change above) Diameter W24x55 BEAM
SBT = A490SC Slip-critical connection Select Bolt Type 3-0.75''dia A490SC
a < 3.5"
n= 3 See below for other SC input Enter Number of Bolts
FLANGE PLATES
Shear Tab W24x55
t= 3/8 0.505 in. Thickness, t
d= 9 23.6 in. Depth, d
SSL STD Select Hole Type in Flange Plates:
Dh = 13/16 13/16 in. Hole dia, Dh 1/4
fy = 36 50 ksi Top and Bottom Plates, fy
fu = 58 65 ksi Top and Bottom Plates, fu
Ab = 0.44 in^2 Area of Bolt, If Slip Critical Prevent slip at service level
Fnv = 38.05 ksi Bolt Shea Capacity Class A or B? mu = 0.5 Slip coefficient, See J3.8
phi = 1.00 Cap = 16.8 k/bolt Du = 1.13
phi Vnb = 50 k Bolt Capacity = phi*N*Fnv*Ab hsc = 0.85
Vu = 42 k Tb = 35
OK Fnv = mu*Du*hsc*Tb*Ns/Ab
5/16
T/B or use CJP
5/16
RESULT SUMMARY
Web of Web of
Shear Tab Shear Tab
W24x55 W24x55
1 OK 0.83 Shear in Bolts
2 OK OK 0.48 0.34 Bearing of Bolts against Steel
3 OK OK 0.57 0.13 Shear on Gross Section
4 OK - 0.65 - Shear Rupture on Net Section
5 OK OK 0.68 0.42 Block Shear
This Spreadsheets is licensed only to Engr. Andro S. Rebuyas, RCE, ME-1, RMP, M.Eng-SE