Identification of The Substance / Mixture and of The Company / Undertaking

Download as pdf or txt
Download as pdf or txt
You are on page 1of 8

SAFETY DATA SHEET

SDS Number: SDS-70111 Version No: 003

Revision Date/Version No:14-03-2017 /3/2.1.1

1. IDENTIFICATION OF THE SUBSTANCE / MIXTURE AND OF THE


COMPANY / UNDERTAKING

Product Name: NIPPELUX 1701 UNDERCOAT


Intended Use: Solvent-Based Decorative Paint
Manufacturer: Nippon Paint (S) Co. Pte Ltd
No. 1 First Lok Yang Road
Jurong Singapore 629728
Emergency Phone Number: (65) 6 265 5355
Fax Numbers: (65) 6 264 1603

2. HAZARDS IDENTIFICATION

GHS Classification:

Physical Hazard
Flammable Hazard Category 3

Health Hazard
Skin corrosion/irritation Category 2
Germ cell mutagenicity Category 1
Carcinogenicity Category 1
Specific target organ toxicity:
- Repeated exposure Category 2

Environmental Hazard
Not classified as an environmental hazard under GHS criteria

GHS Pictogram

Signal Word
Danger

Hazard statements
H226: Flammable liquid and vapour
H315: Causes skin irritation
H340: May cause genetic defects
H350: May cause cancer

Page 1 of 8
NIPPELUX 1701 UNDERCOAT

H373: May cause damage to organs through prolonged or repeated exposure

Precautionary statements
P201: Obtain special instructions before use
P202: Do not handle until all safety precautions have been read and understood
P210: Keep away from heat/sparks/open flames/hot surfaces – No smoking
P233: Keep container tightly closed
P240: Ground/bond container and receiving equipment
P241: Use explosion-proof electrical/ventilating/light/equipment
P242: Use only non-sparking tools
P243: Take precautionary measures against static discharge
P260: Do not breathe dust/fume/gas/mist/vapours/spray
P264: Wash hands thoroughly after handling
P280: Wear protective gloves/protective clothing/eye protection/face protection
P281: Use personal protective equipment as required

Response
P314: Get medical advice/attention if you feel unwell
P321: Specific treatment (see Section 4 of SDS)
P362: Take off contaminated clothing and wash before reuse
P302+352: IF ON SKIN: Wash with soap and water
P308+313: IF exposed or concerned: Get medical advice/attention
P332+313: If skin irritation occurs: Get medical advice/attention
P370+378: In case of fire: Use appropriate media for extinction
P303+361+353: IF ON SKIN (or hair): Remove/Take off immediately all contaminated clothing.
Rinse skin with water/shower

Storage
P405: Store locked up
P403+235: Store in a well ventilated place. Keep cool

Disposal
P501: Dispose of contents/container to appropriate waste site or reclaimer in accordance with local
or national regulations

3. COMPOSITION / INFORMATION ON INGREDIENTS

Substances CAS No. %


Alkyd Resin - 8-17
Low boiling point hydrogen treated naptha 64742-82-1 3-7
Substances determined to be non-hazardous - Balance
100%

4. FIRST-AID MEASURES

INHALATION
Move person to fresh air and call for medical assistance immediately.
If not breathing, give artificial respiration, if breathing is difficult, give oxygen. Keep at rest.

SKIN CONTACT
In case of contact, immediately flush skin with large amounts of water and soap while
removing contaminated clothing and shoes.

Page 2 of 8
NIPPELUX 1701 UNDERCOAT

If irritation persists, get medical attention.

EYE CONTACT
Immediately flush eyes with large amounts of water until irritation subsides.
Remove contact lens.
Obtain medical attention, preferably by an ophthalmologist, immediately.

INGESTION
DO NOT induce vomiting unless directed to do so by a medical personnel. Never give
anything by mouth to an unconscious person. Keep at rest. Get medical attention immediately.

5. FIRE FIGHTING MEASURES

SUITABLE FIRE EXTINGUISHING MEDIA


Alcohol - resistant foam, Carbon dioxide, or dry chemical type.

SPECIFIC HAZARDS ARISING FROM THE CHEMICAL


Combustion products may include and are not limited to: Carbon monoxide and Carbon
dioxide.

SPECIAL PROTECTIVE ACTIONS FOR FIRE FIGHTERS


Wear full protective clothing and NIOSH - approved self - contained breathing apparatus.
Use water spray to cool fire - exposed surfaces and to protect personnel. If a leak or spill has
not ignited, use water spray to disperse the vapours.
If possible, isolate product from heat, electrical equipments, sparks and open flames.
Avoid spraying water directly into storage containers.
Closed containers may explode when exposed to extreme heat.
Avoid spreading burning liquid with water, isolate liquid.
Do not allow runoff from fire fighting to enter drains or watercourses.

6. ACCIDENTAL RELEASE MEASURES

PERSONAL PRECAUTIONS, PROTECTIVE EQUIPMENT AND EMERGENCY PROCEDURE


Wear appropriate protective equipment, e.g. respirators, eye protection, gloves and safety
shoes.
Avoid substance contact with eyes. Do not inhale vapours.
Ensure supply of fresh air in enclosed rooms.

ENVIRONMENTAL PRECAUTIONS
Eliminate sources of ignition.
Keep public away.
Contain spilled liquid with sand or other non-combustible absorbent materials.
Wash area and prevent runoff into drains and sewerage system.
Advise authorities if substance has entered a watercourse or sewer or has contaminated soil
or vegetation.

METHODS AND MATERIALS FOR CONTAINMENTS AND CLEANING UP


Clean up all spills immediately.
Absorb spill with absorbent and inert material, then place in container.
Disposal in accordance to local/national regulations.

Page 3 of 8
NIPPELUX 1701 UNDERCOAT

7. HANDLING AND STORAGE

PRECAUTIONS FOR SAFE HANDLING


Use appropriate personal protective equipment.
Keep out of reach of children.
Handle containers with care. Open slowly in order to control possible pressure release.
Do not pressurize containers.
Do not ingest. Do not breathe in gas/fumes/vapour. Avoid contact with skin and eyes.
For personal protection, see section 8.
Use only in areas from which all naked lights and other sources of ignition have been
excluded.
Take precautionary measures against static discharge.
Protect from frost and extremes of temperature.

CONDITIONS FOR SAFE STORAGE, INCLUDING ANY INCOMPATIBILTIES


Keep containers tightly closed.
Containers that are opened should be properly resealed and kept upright to prevent leakage.
Store in cool, dry and well - ventilated place at temperature between 20°C to 40°C away from
heat and sources of ignition.

8. EXPOSURE CONTROLS / PERSONAL PROTECTION

CONTROL PARAMETERS/OCCUPATIONAL LIMITS


ACGIH TLV-TWA OSHA PEL-TWA
Substances
ppm mg/m3 ppm mg/m3
Alkyd Resin - - - -
Low boiling point hydrogen treated naptha - 525.00 - -

APPROPRIATE ENGINEERING CONTROL MEASURES


Provide exhaust ventilation or other engineering controls to keep the airborne concentrations
of vapours below their respective occupational exposure limits.
Ensure eyewash stations and safety showers are close to the workstation location.

PERSONAL PROTECTION
Respiratory Protection: Use of NIOSH - approved respirators with organic vapour
cartridges is recommended.
Hand Protection: Use of solvent resistance type or chemical resistant type of
protective gloves is recommended.
Eye Protection: Use of safety glasses or goggles with side shields is
recommended.
Skin / Body Protection: Wear chemical resistant clothes and safety shoes when
handling product.

9. PHYSICAL AND CHEMICAL PROPERTIES

Appearance : Liquid
Odour : Aromatic hydrocarbon odour
Odour threshold : Not available
pH : Not available
Melting point/freezing point : Not available

Page 4 of 8
NIPPELUX 1701 UNDERCOAT

Initial boiling point and boiling range : Between 90 and 169 °C


Flash point : 43 °C
Evaporation rate : Not available
Flammability (solid, gas) : Not applicable
Lower flammability or explosive limit : 0.9 % by vol
Upper flammability or explosive limit : 6.7 % by vol
Vapour pressure : Not available
Vapour density : > 1.00 (Vapour is heavier than air)
Relative density : Not available
Solubility : Not Miscible in water
Partition coefficient : Not available
Auto-ignition temperature : > 230 °C
Decomposition temperature : Not available
Viscosity : 73 - 77 KU

10. STABILITY AND REACTIVITY

REACTIVITY
No dangerous reaction known under condition of normal use.

CHEMICAL STABILITY
The product is stable under recommended storage and handling conditions. (see section 7)

POSSIBILITY OF HAZARDOUS REACTION


Under normal conditions of storage and use, hazardous reaction will not occur.

CONDITIONS TO AVOID
Keep away from oxidising agents, strongly alkaline and strongly acidic materials in order to
avoid exothermic reactions. Avoid all possible sources of ignition (spark or flame). Do not
pressurize, cut, weld, braze, drill, grind or expose containers to heat or sources of ignition.

HAZARDOUS DECOMPOSITION PRODUCTS


When exposed to high temperatures may produce hazardous decomposition products such as
carbon monoxide, carbon dioxide, oxides of nitrogen and smoke.

11. TOXICOLOGICAL INFORMATION

There is no data available on the product itself.


Toxicological information of substances:
Acute oral toxicity
Harmful if swallowed
Substances Oral LD50(Rat), mg/kg
Alkyd Resin Data not available
Low boiling point hydrogen treated naptha Data not available

Acute dermal/skin toxicity


May be harmful if in contact with skin
Substances Dermal LD50 (Rabbit), mg/kg
Alkyd Resin Data not available
Low boiling point hydrogen treated naptha Data not available

Page 5 of 8
NIPPELUX 1701 UNDERCOAT

Acute inhalation toxicity


Vapour concentrations above the recommended exposure levels may be irritating to the eyes and
the respiratory tract, may cause headaches and dizziness, could be anesthetic and may have other
central nervous system effects.
Substances Inhalation Vapor LC50 (Rat), mg/L/4hr
Alkyd Resin Data not available
Low boiling point hydrogen treated naptha Data not available

Skin corrosion or irritation


Causes skin irritation. Frequent or prolonged contact may dry the skin, leading to discomfort and
dermatitis.

Serious eye damage or irritation


May be an eye irritant

Respiratory or skin sensitisation


Vapour concentrations above the recommended exposure levels may be irritating to the eyes and
the respiratory tract

Germ cell mutagenicity


No information available on the product

Carcinogenicity
Titanium Dioxide
The International Agency for Research on Cancer (IARC) has classified Titanium Dioxide as
possibly carcinogenic to humans (Group 2B) based on inadequate evidence of carcinogenicity in
humans and sufficient evidence of carcinogenicity in experimental animals
Reproductive toxicity
No information available on the product

Specific Target Organ Toxicity (STOT)-single exposure


No information available on the product

Specific Target Organ Toxicity (STOT)-repeated exposure


No information available on the product

Asphyxiation hazard
May be harmful if swallowed and enters airways

12. ECOLOGICAL INFORMATION

Toxicity
Aquatic toxicity -No data available

Persistence and degradability


Biodegradation -No data available

Bioaccumulative potential
No data available

Mobility in soil
No data available

Page 6 of 8
NIPPELUX 1701 UNDERCOAT

Result of PBT and vPvB assessment


No data available

Other adverse effects


There is no ecotoxicological test data available on the product itself.
The product should not be allowed to enter drains or water courses.

13. DISPOSAL CONSIDERATIONS

The product should not be allowed to enter drains and watercourses.


Preferred methods of waste disposal are incineration or biological treatment in federal/state
approved facility. Empty containers should be recycled or disposed through an approved waste
management facility or licensed contractor.
All federal, state and local environmental regulations shall be observed.

14. TRANSPORT INFORMATION

Transport to be in accordance with ADR/RID for road/rail, IMDG for sea and IATA for Air.
LAND TRANSPORT
Classified as Dangerous Goods by the criteria of the European Agreement concerning the
international carriage of Dangerous Goods (ADR) by Road & Regulations concerning the
international carriage of Dangerous goods (RID) by Rail.
UN Number: 1263
Proper shipping name: PAINT (including paint, lacquer, enamel , stain, shellac, varnish, polish,
liquid filler and liquid lacquer base) or PAINT RELATED MATERIAL
(including paint thinning or reducing compound)
Class: Class 3
Packaging Group: III

SEA TRANSPORT
Classified as Dangerous Goods by the criteria of the International Maritime Dangerous Goods
Code (IMDG Code) for transport of Sea.
UN Number: 1263
Proper shipping name: PAINT (including paint, lacquer, enamel, stain, shellac, varnish, polish,
liquid filler and liquid lacquer base) or PAINT RELATED MATERIAL
(including paint thinning or reducing compound)
Class: Class 3
Packaging Group: III
Marine Pollutant No

SEA (ANNEX II OF MARPOL 73/78 AND THE IBC CODE)


Not applicable
AIR TRANSPORT
Classified as Dangerous Goods by the criteria of the International Air Transport Association (IATA)
Dangerous Goods Regulations for transport by Air
UN Number: 1263
Proper shipping name: PAINT (including paint, lacquer, enamel, stain, shellac, varnish, polish,
liquid filler and liquid lacquer base) or PAINT RELATED MATERIAL
(including paint thinning or reducing compound)
Class: Class 3

Page 7 of 8
NIPPELUX 1701 UNDERCOAT

Packaging Group: III

15. REGULATORY INFORMATION

Applicable national regulations:

Standards on Hazard communication for hazardous chemicals and dangerous goods


- SS 586: Part 1: 2014-Transport and storage of dangerous goods
- SS 586: Part 2: 2014-GHS of classification and labelling of chemicals
- SS 586: Part 3: 2008(2014)-Preparation of safety data sheet
MOM: Workplace Safety and Health Act & Workplace Safety and Health (General Provisions)
Regulations
- This product is subject to SDS, labelling, PEL and other requirements in the
Acts/Regulations.
NEA: Environmental Protection and Management Act & Environmental Protection and
Management (Hazardous Substances) Regulations
- This product is not subject to control under this Acts/Regulations.
SCDF: Fire Safety Act & Fire Safety (Petroleum and Flammable Materials) Regulations
- This product is subject to the requirement of this Acts/Regulations.
SPF: The Arms and Explosive Act, the Arms and Explosives (Explosives) Rules, and the Arms
and Explosives (Explosive Precursors) Rules
- This product is not subject to the requirement of this Acts/Regulations.

16. OTHER INFORMATION

Revision Date/Version No.: 14-03-2017 /3/2.1.1


History
Previous Revision Date /Version No.: 20-03-2015 /3/1.1.1

Abbreviation
ACGIH American Conference of Governmental Industrial Hygienists
TLV Threshold limit value
TWA Time-Weighted Average
OSHA Occupational Safety and Health Administration
PEL Permissible Exposure Limit
LD50 Lethal Dose
LC50 Median lethal concentration
IARC International Agency for Research in Cancer

Disclaimer
To the best of our knowledge, the information contained herein is accurate. However, the
information is provided without any representation or warranty, expressed or implied, regarding its
accuracy or completeness. Since the conditions of handling, storage, use and disposal are beyond
our control and may be beyond our knowledge, for this and other reasons, we make no guarantee
of results and assume no liability for damages incurred by the use of this product. Please be
reminded that all chemicals may present unknown health hazards and should be used with caution.

Page 8 of 8

You might also like