Scribd Logo
Upload

Welcome to Scribd!

  • Mazak Fusion 640 Series How To Create A Backup Using RS232

    Uploaded by

    sunhuynh
    2K views5 pages
    Mazak

    Original Title

    Mazak Fusion 640 Series How to Create a Backup Using RS232

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Report this Document
    Mazak

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Flag for inappropriate content
    Download as pdf or txt
    2K views5 pages

    Mazak Fusion 640 Series How To Create A Backup Using RS232

    Uploaded by

    sunhuynh
    Mazak

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Flag for inappropriate content
    Download as pdf or txt
    of 5

    CNC Procedure

    CNC
    M600
    Mazak Fusion M640 backup using RS232

    Overview
    The purpose of this procedure is to guide you through the steps on how to back-up the Fusion control through Data I/O using
    RS232

    Tools Needed
    • RS232 Cable
    • Laptop
    Instructions
    I. Configure settings
    A. Configuring laptop software settings
    1. Set up your software settings (example shows using ProComm Plus)

    2. Set Baud rate to 4800


    3. Set Parity to Even
    4. Set Data bits to 7
    5. Set stop bits to 2

    B. Setup Controller
    1. Select {DATA I/O}

    2. Select {TAPE}

    3. Select {PARAM}

    Page 1 of 5

    • Specifications subject to change without notice. • An ISO9001 Certified Company us.mitsubishielectric.com/fa/en Serving the Americas ISO-NUMBER-XXXX
    ©2014, Mitsubishi Electric Automation, Inc. • All rights reserved. • 500 Corporate Woods Parkway • Vernon Hills, IL 60061 • Phone 847.478.2500 • Fax 847.478.2650
    CNC Procedure
    CNC
    M600
    Mazak Fusion M640 backup using RS232

    4. Set the parameters to the following settings

    5. Press the {PARAM DETAIL} soft key

    6. Set the TAP parameters to the following settings

    7. On the top left corner of the Data I/O screen. Press the {SETUP} tab
    8. Press the {Extended Param} setting

    Page 2 of 5

    • Specifications subject to change without notice. • An ISO9001 Certified Company us.mitsubishielectric.com/fa/en Serving the Americas ISO-NUMBER-XXXX
    ©2014, Mitsubishi Electric Automation, Inc. • All rights reserved. • 500 Corporate Woods Parkway • Vernon Hills, IL 60061 • Phone 847.478.2500 • Fax 847.478.2650
    CNC Procedure
    CNC
    M600
    Mazak Fusion M640 backup using RS232

    9. Set the parameters to the following settings

    C. Output data
    1. Connect your RS232 cable (Refer to Index)
    2. Select {DATA I/O}

    3. Select {TAPE}

    4. Select {PUNCH NC->TAPE}

    5. Select {PROGRAM FILE}


    6. Press on {PAGE SAVE} to save all the programs
    7. With keyboard highlight all the data to transfer

    Page 3 of 5

    • Specifications subject to change without notice. • An ISO9001 Certified Company us.mitsubishielectric.com/fa/en Serving the Americas ISO-NUMBER-XXXX
    ©2014, Mitsubishi Electric Automation, Inc. • All rights reserved. • 500 Corporate Woods Parkway • Vernon Hills, IL 60061 • Phone 847.478.2500 • Fax 847.478.2650
    CNC Procedure
    CNC
    M600
    Mazak Fusion M640 backup using RS232

    8. Get your software ready to receive the file


    9. Press the {START} soft key
    10. You should see the data transferring

    Page 4 of 5

    • Specifications subject to change without notice. • An ISO9001 Certified Company us.mitsubishielectric.com/fa/en Serving the Americas ISO-NUMBER-XXXX
    ©2014, Mitsubishi Electric Automation, Inc. • All rights reserved. • 500 Corporate Woods Parkway • Vernon Hills, IL 60061 • Phone 847.478.2500 • Fax 847.478.2650
    CNC Procedure
    CNC
    M600
    Mazak Fusion M640 backup using RS232

    Appendix
    RS232 Cable Configuration

    If you get alarms such as "541 TAPE PUNCHER MIS-CONNECTED" you need to check your
    connections. Make sure you are connected to COM1 port on the back of the NC keyboard

    Page 5 of 5

    • Specifications subject to change without notice. • An ISO9001 Certified Company us.mitsubishielectric.com/fa/en Serving the Americas ISO-NUMBER-XXXX
    ©2014, Mitsubishi Electric Automation, Inc. • All rights reserved. • 500 Corporate Woods Parkway • Vernon Hills, IL 60061 • Phone 847.478.2500 • Fax 847.478.2650

    You might also like