Australian Standard: Gaseous Fire Extinguishing Systems
Australian Standard: Gaseous Fire Extinguishing Systems
Australian Standard™
Australian Standard™
COPYRIGHT
© Standards Australia
All rights are reserved. No part of this work may be reproduced or copied in any form or by
any means, electronic or mechanical, including photocopying, without the written
permission of the publisher.
Published by Standards Australia, GPO Box 5420, Sydney, NSW 2001, Australia
ISBN 0 7337 4803 1
AS 4214—2002 2
PREFACE
This Standard was prepared by the Standards Australia Committee FP-011, Gaseous Fire
Extinguishing Systems, to supersede AS 4214—1995, Gaseous fire extinguishing systems—
General requirements.
This Standard incorporates Amendment No. 1 ( May 2005). The changes required by the
Amendment are indicated in the text by a marginal bar and amendment number against the
clause, note, table, figure or part thereof affected.
This revision is based on ISO 14520.1 and NFPA 12, Carbon dioxide extinguishing systems.
The Committee has introduced higher levels of safety and security. Additionally, this
revision includes a section dedicated to marine application. Appendices cover gaseous
agents including an appendix for carbon dioxide.
It is essential that gaseous fire extinguishing systems be maintained to ensure instant
readiness when required. The importance of maintenance cannot be too highly emphasized.
Maintenance requirements for gaseous systems are detailed in AS 1851.12 (see Clause 1.4).
Gas containers manufactured for use in Australia are required to meet the design criteria set
out in AS 2030.1, The approval, filling, inspection, testing and maintenance of containers
for the storage and transport of compressed gases, Part 1: Containers for compressed gases
other than acetylene.
Attention is drawn to AS 2030.1, as it requires containers to be designed for a pressure
developed at the nominated maximum temperature of 65°C. This is some 10°C higher than
that nominated in overseas codes. Accordingly, this aspect should be kept in mind for any
imported containers.
It is a basic assumption in all technical standards work that each Standard be used only by
persons competent in the field of application. This is of particular importance in fire
protection work. Accordingly, it is emphasized that only trained and experienced designers
interpret the design requirements contained herein.
The term ‘normative’ has been used in this Standard to define the application of the
appendix to which it applies. A ‘normative’ appendix is an integral part of this Standard.
CONTENTS
Page
FOREWORD.............................................................................................................................. 6
SECTION 5 SUPPLY
5.1 QUALITY ................................................................................................................. 34
5.2 STORAGE CONTAINER DESIGN .......................................................................... 34
5.3 STORAGE CONTAINER ARRANGEMENT........................................................... 34
5.4 VALVES ................................................................................................................... 35
5.5 PRESSURE-REDUCTION DEVICES ...................................................................... 36
AS 4214—2002 4
Page
SECTION 8 MARKING
8.1 CONTROL AND INDICATING EQUIPMENT (CIE).............................................. 46
8.2 WARNING NOTICES .............................................................................................. 46
8.3 NUMBER OF CONTAINERS AND QUANTITY MARKING................................. 49
8.4 IDENTIFICATION AND MARKING OF CONTAINERS ....................................... 49
8.5 LABELLING OF INDICATORS AND CONTROLS................................................ 50
8.6 IDENTIFICATION OF DISCHARGE NOZZLES .................................................... 50
SECTION 9 MARINE
9.1 GENERAL ................................................................................................................ 51
9.2 USE AND LIMITATIONS........................................................................................ 51
9.3 AGENT SELECTION ............................................................................................... 52
9.4 SAFETY REQUIREMENTS ..................................................................................... 52
9.5 SYSTEM DESIGN .................................................................................................... 52
9.6 ENCLOSURE REQUIREMENTS............................................................................. 56
9.7 AGENT SUPPLY ...................................................................................................... 57
This is a free 9 page sample. Access the full version online.
Page
APPENDICES
A COMMISSIONING CHECK LIST............................................................................ 66
B DISCHARGE TEST .................................................................................................. 68
C CERTIFICATE OF COMPLETION.......................................................................... 70
D DOOR FAN TEST FOR DETERMINATION OF MINIMUM HOLDING TIME .... 72
E GASEOUS FIRE EXTINGUISHING SYSTEMS
USING IG-541 (INERGEN) EXTINGUISHING AGENT-INERT............................ 80
F GASEOUS FIRE EXTINGUISHING SYSTEMS
USING CARBON DIOXIDE (CO2) EXTINGUISHING AGENT............................. 89
A1 G GASEOUS FIRE EXTINGUISHING SYSTEMS USING IG-55 (ARGONITE)
EXTINGUISHING AGENT—INERT..................................................................... 116
H GASEOUS FIRE EXTINGUISHING SYSTEMS USING FIC-13I1 (CF3I)
TRIFLUOROIODOMETHANE (TRIODIDE) EXTINGUISHING AGENT—
HALOCARBON...................................................................................................... 124
I GASEOUS FIRE EXTINGUISHING SYSTEMS
USING HCFC BLEND A (NAF S-III) EXTINGUISHING AGENT—
HALOCARBON...................................................................................................... 132
J GASEOUS FIRE EXTINGUISHING SYSTEMS
USING HFC-227ea (FM-200) EXTINGUISHING AGENT—HALOCARBON ..... 140
K GASEOUS FIRE EXTINGUISHING SYSTEMS
USING HFC-23 (FE-13) EXTINGUISHING AGENT—HALOCARBON ............. 149
This is a free 9 page sample. Access the full version online.
AS 4214—2002 6
FOREWORD
Gaseous fire extinguishing systems covered in this Standard are intended to extinguish,
suppress or inert fires.
Several different extinguishing agents have been developed in recent years, and there is a
need for dissemination of information on systems and the design methods required for their
extinguishing agents. This Standard has been prepared to meet this need.
Gaseous fire extinguishing systems utilizing extinguishing agents that have been supported
by the presentation of full technical data to the Committee have been included in the
appendices. These data include relevant details on the health and safety aspects,
environmental acceptability and the system design methods, hardware and software.
In addition, alternative requirements to the release of extinguishing agents during testing
and commissioning procedures have been included. These are linked to the inclusion of
enclosure integrity testing.
The requirements of this Standard are made in the light of the best technical data known to
the Committee at the time of writing, but since a wide field is covered it has been
impracticable to consider every possible factor or circumstance that might affect
implementation of the recommendations.
This Standard has been prepared on the basis that personnel with the appropriate levels of
skill, training and practical experience would undertake the functions associated with the
design, installation, testing and commissioning of gaseous fire extinguishing systems, to
provide safe and satisfactory performance, including exercising a duty of care to avoid
unnecessary release of extinguishing agent.
It is important that the protection of a structure, building or plant be considered on a
holistic approach basis. Gaseous fire extinguishing systems form only a part of the available
facilities, but it should not be assumed that their adoption necessarily removes the need to
consider supplementary measures, such as the provision of portable fire extinguishers or
other mobile appliances for first aid or emergency use, or to deal with special hazards.
Gaseous fire extinguishing systems have for many years been recognized as effective for
extinguishing flammable liquid fires and fires in the presence of electrical and ordinary
Class A hazards. However, when planning systems, designers should be aware that there
may be hazards for which these agents are not suitable, or that in certain circumstances or
situations there may be dangers in their use, which will require special precautions.
Advice on these matters can be obtained from the manufacturers of gaseous fire
This is a free 9 page sample. Access the full version online.
extinguishing systems. Additional information can also be sought from fire authorities,
health and safety authorities, insurers and the authority having jurisdiction.
Gaseous fire extinguishing systems need to be maintained to ensure readiness when
required. The importance of maintenance cannot be too highly emphasized.
7 AS 4214—2002
STANDARDS AUSTRALIA
Australian Standard
Gaseous fire extinguishing systems
1.1 SCOPE
This Standard sets out requirements for design, installation, testing and commissioning of
gaseous fire extinguishing systems for both total flooding and local application types. It
A1
applies to central and distributed supply systems.
This Standard does not apply to explosion suppression.
This Standard deals with systems utilizing electrically non-conducting extinguishing agents
that do not leave a residue after discharge and for which there is sufficient data currently
available to enable validation of performance characteristics by an internationally
recognized fire protection test and approval body (see Clause 1.9). It is not intended to
indicate approval by the authorities having jurisdiction of the systems utilizing the agents
included in Table 1.1. It is essential that this Standard be used in conjunction with its
separate, specific extinguishing agent contained in the appendices of this Standard.
The characteristics of extinguishing agents and their suitability for classes of fire are also
considered.
NOTES:
1 This Standard should be read in conjunction with AS 1851.12, which covers inspection,
testing and maintenance of gaseous fire extinguishing systems.
2 Gas pressures have been expressed in bars with the SI units (MPa, kPa) shown in brackets
immediately following.
3 Where values have been obtained from sources such as NFPA, they have been conservatively
rounded.
A1
4 For the purposes of this Standard, fire extinguishing includes inerting.
This is a free 9 page sample. Access the full version online.
SAI Global also carries a wide range of publications from a wide variety of Standards Publishers: