3.5.3.5 Lab - Configure and Verify eBGP
3.5.3.5 Lab - Configure and Verify eBGP
3.5.3.5 Lab - Configure and Verify eBGP
672017111
Lab - Configure and Verify eBGP
Topology
Addressing Table
Objectives
Part 1: Build the Network and Configure Basic Device Settings
Part 2: Configure eBGP on R1
Part 3: Verify eBGP Configuration
Background / Scenario
In this lab you will configure eBGP for the Company. The ISP will provide the default route to the Internet.
Once configuration is complete you will use various show commands to verify that the eBGP configuration is
working as expected.
Required Resources
3 Routers (Cisco 1941 with Cisco IOS Release 15.2(4)M3 universal image or comparable)
Console cables to configure the Cisco IOS devices via the console ports
© 2021 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 5
Lab – Configure and Verify eBGP
Step 1: Enable BGP and identify the AS number for the Company.
R2(config)# router bgp 65000
Step 2: Use the neighbor command to identify ISP-1 as the BGP peer.
R2(config-router)# neighbor 209.165.200.1 remote-as 65001
Step 3: Add the Company’s network to the BGP table so it is advertised to ISP-1.
R2(config-router)# network 198.133.219.0 mask 255.255.255.248
© 2021 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 2 of 5
Lab – Configure and Verify eBGP
© 2021 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 3 of 5
Lab – Configure and Verify eBGP
Ping the Web Server from R1. Were the pings successful? (Note: For the pings to succeed, a static default
route must be configured on R1 using the serial 0/0/0 interface as the exit interface.) Iya
Reflection
The topology used in this lab was created to demonstrate how to configure the BGP routing protocol. However,
the BGP protocol would not normally be configured for a topology like this in the real world. Explain.
Di dunia nyata perusahaan ISP akan memberikan subnet dan alamat IP dan dalam hal ini perusahaan ISP itu
sendiri akan bertanggung jawab untuk merutekan lalu lintas, sehingga ISP akan mengkonfigurasi BGP.
© 2021 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 4 of 5
Lab – Configure and Verify eBGP
Router Model Ethernet Interface #1 Ethernet Interface #2 Serial Interface #1 Serial Interface #2
1800 Fast Ethernet 0/0 Fast Ethernet 0/1 Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1)
(F0/0) (F0/1)
1900 Gigabit Ethernet 0/0 Gigabit Ethernet 0/1 Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1)
(G0/0) (G0/1)
2801 Fast Ethernet 0/0 Fast Ethernet 0/1 Serial 0/1/0 (S0/1/0) Serial 0/1/1 (S0/1/1)
(F0/0) (F0/1)
2811 Fast Ethernet 0/0 Fast Ethernet 0/1 Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1)
(F0/0) (F0/1)
2900 Gigabit Ethernet 0/0 Gigabit Ethernet 0/1 Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1)
(G0/0) (G0/1)
Note: To find out how the router is configured, look at the interfaces to identify the type of router and how many
interfaces the router has. There is no way to effectively list all the combinations of configurations for each router
class. This table includes identifiers for the possible combinations of Ethernet and Serial interfaces in the device.
The table does not include any other type of interface, even though a specific router may contain one. An
example of this might be an ISDN BRI interface. The string in parenthesis is the legal abbreviation that can be
used in Cisco IOS commands to represent the interface.
© 2021 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 5 of 5