Smbus Controlled Nvdc-1 Charge Controller, N-CH Mosfet Selector and Current Monitor

User's Guide
SLUUA74 – January 2013
SMBus Controlled NVDC-1 Charge Controller, N-CH

MOSFET Selector and Current Monitor
The bq2471x evaluation module (EVM) is an SMBus controlled NVDC-1 charge controller with N-CH
MOSFET selector and current monitoring. The input voltage range, for the buck converter, is between 6
and 24 V, with a programmable output of 2–3 cells (bq24715) and 3–4 cells (bq24717) and charge output
current range of 128 mA to 8.128 A.
This EVM doesn’t include the EV2400 interface device (HPA500); this must be ordered separately to
evaluate the bq2471x EVM.
Contents
1 Introduction .................................................................................................................. 2
1.1 Features ............................................................................................................. 2
1.2 I/O Descriptions .................................................................................................... 2
1.3 Jumpers ............................................................................................................. 3
2 Test Summary ............................................................................................................... 3
2.1 Equipment ........................................................................................................... 3
2.2 Equipment Setup ................................................................................................... 4
3 Procedure .................................................................................................................... 8
3.1 Power-up and Initial Checks ...................................................................................... 8
3.2 Charge Regulation and System Load Checks ................................................................. 8
3.3 Equipment Shutdown .............................................................................................. 9
4 PCB Layout Guideline .................................................................................................... 10
5 Bill of Materials (BOM) PCB Layout and Schematic .................................................................. 11
5.1 Bill of Materials (BOM) ........................................................................................... 11
5.2 Schematic ......................................................................................................... 13
5.3 Layouts ............................................................................................................. 14
List of Figures
1 Connections of the EV2400 Kit ........................................................................................... 5
2 Original test setup for PWR115 (bq24715 EVM) ....................................................................... 6
3 a) bq24715 GUI Interface Window; b) bq24717 GUI Interface Window ............................................. 7
4 Test setup for PWR115 .................................................................................................... 9
5 bq2471x Schematic ....................................................................................................... 13
6 Assembly Layer ............................................................................................................ 14
7 Top Layer ................................................................................................................... 15
8 Layer 2 ...................................................................................................................... 16
9 Layer 3 ...................................................................................................................... 17
10 Bottom Layer ............................................................................................................... 18
List of Tables
1 I/O Descriptions ............................................................................................................. 2
2 Recommended Operating Conditions .................................................................................... 3
3 EV2400 and bq24715 EVM Connections ................................................................................ 4
4 PWR115A BOM ........................................................................................................... 11
SLUUA74 – January 2013 SMBus Controlled NVDC-1 Charge Controller, N-CH MOSFET Selector and 1
Submit Documentation Feedback Current Monitor
Copyright © 2013, Texas Instruments Incorporated
Introduction www.ti.com
1 Introduction
1.1 Features
Refer to the data sheet (SLUSBD1) for detailed features and operation.
1.2 I/O Descriptions
Table 1. I/O Descriptions

Jack Description
J1–DCIN AC to VDC adapter, positive output
J1–GND AC to VDC adapter, negative output
J2–SCL SCL pin output, SMBus clock line
J2–SDA SDA pin output, SMBus data line
J2– GND External power supply, negative output
J3-Cell External input for disable learn pulse
J3-ACOK ACOK pin
J3-IOUT IOUT pin
J3-3.3V External voltage supply 3.3 V
J4-SYS Connected to system
J4-GND Ground
J4-BAT Connected to battery pack
2 SMBus Controlled NVDC-1 Charge Controller, N-CH MOSFET Selector and SLUUA74 – January 2013
Current Monitor Submit Documentation Feedback
www.ti.com Test Summary
1.3 Jumpers
JP1
bq24715: 2 Cells – Float, 3 Cells – Apply Jumper (High);
bq24717: 3 Cells – Float, 4 Cells – Apply Jumper (High);
Table 2. Recommended Operating Conditions

Description Min Typ Max Unit
VIN Supply voltage Input voltage from ac adapter input 18 19–20 22 V
VBAT Battery voltage Voltage applied at VBAT terminal 0 6–12.6 17.408 V
IAC Supply current Maximum input current from ac adapter input 0 4.5 A
Iout Output current Output current 1 8 A
TJ Operating junction temperature range 0 125 °C
2 Test Summary
2.1 Equipment
Power Supplies
Power supply #1 (PS#1): a power supply capable of supplying 20 V at 5 A is required.
Power supply #2 (PS#2): a power supply capable of supplying 3.3 V at 0.2 A is required.
Load #1
A 20-V (or above), 10-A (or above) electronic load that can operate at constant current mode
Load #2
A Kepco BOP36-12M, 0~±36 V/0~±12 A, bipolar operational power supply
Or: equivalent
Meters
Seven Fluke 75 multimeters, (equivalent or better)
or: Four equivalent voltage meters and three equivalent current meters.
The current meters must be capable of measuring 5 A+ current.
Computer
A computer with at least one USB port and a USB cable. The EV2400 USB driver and the bq24715 SMB
evaluation software must be properly installed.
EV2400 SMBUS Communication Kit
An EV2400 SMBUS communication kit
EV2400 Controller
The EV2400 controller is an MSP430F5529 running at 4 MHz. The controller firmware is stored in flash
memory and is executed by the core at power-up. The controller communicates with target device(s)
through either: a 2-wire SMBus communication port, a 1-wire HDQ port, or a 2-wire EEPROM I2C port.
The 2-wire SMBus communication port supports both SMBus and I2C protocols. CRC-8 checksum
verification for the data packets prevents data corruption over the USB.
USB Interface (USB)
The interface board connects to a USB port (version 1.1 or later) on a host computer and is powered from
the port. All communication over the USB is human interface device (HID) class. Drivers are built into
Windows® and most of the operating systems.
Test Summary www.ti.com
2.2 Equipment Setup

(A) Set the PS#1 for 0 V ±100 mVDC, with the current limit set to > 5 A, then turn off supply.
(B) Connect the output of PS#1 in series with a current meter (multimeter) to J1 (DCIN, GND).
(C) Connect a voltage meter across J1 (DCIN, GND).
(D) Set the PS#2 for 3.3 V ±100 mVDC, 0.2 ±0.1 A current limit and then turn off supply.
(E) Connect the output of the PS#2 to J3 (3.3V) and J4 (GND).
(F) Connect a voltage meter across J4 (BAT, GND).
(G) Connect a voltage meter across J4 (SYS, GND).
(H) Connect J2 (SDA, SCL) and J2 (GND) to the EV2400 kit SMB port. Refer to Table 3 for a connection
reference. Connect the USB port of the EV2400 kit to the USB port of the computer. The connections
are shown in Figure 1.
Table 3. EV2400 and bq24715 EVM Connections

Bq24715 EVM-115 EV2400
GND (J2) GND (1)
SCL (J2) SMBC (2)
SDA (J2) SMBD (3)
Figure 1. Connections of the EV2400 Kit
(I) If JP1 is not installed, install the jumper.

(J) After the steps above, the test setup for PWR115 is shown in Figure 2.
Test Summary www.ti.com
Figure 2. Original test setup for PWR115 (bq24715 EVM)
(K) Turn on the computer. Open the bq24715_717_GUI evaluation software. The GUI windows of the
bq24715/7 3/4 cell-setting software are shown in Figure 3. The register values are read later in the
procedure, after PS#2 is powered. For 3-cell bq24715 setting, the 0x15 and 0x3E register values are
different.
Figure 3. a) bq24715 GUI Interface Window; b) bq24717 GUI Interface Window

Procedure www.ti.com
3 Procedure
3.1 Power-up and Initial Checks
3.1.1 Make sure EQUIPMENT SETUP steps are followed. Turn on PS#2.
**NOTE** Load #1 and Load #2 are not connected during this step.
3.1.2 Turn on PS#1

Increase the output voltage of PS#1 to 19.5 V and measure values with regard to GND.
3.1.3 Verify the Following Parameters

Measure → V(TP3 (ACDET)) = 2.6 V ±0.1 V
Measure → V(TP14 (ACOK)) = 3.3 V ±0.1 V
Measure for -001 → V(J4(SYS)) = 13.5 V ±0.5 V
Measure for -002 → V(J4(SYS)) = 17.5 V ±0.5 V
Measure → V(TP15 (REGN)) = 6 V ±0.5 V
Measure → V(J4(BAT, GND)) = 1 V ±1.1 V
Measure → V((TP2(ACDRV) with regard to TP1 (CMSRC)) = 6 V ±0.5 V
3.1.4 Default Parameters Settings

Click on Actions and Read all Registers in the GUI software. Make sure there is no error information
generated. Verify reading for -001/2 in Figure 3 a/b respectively. Skip to Section 3.2, if no errors.
If there is an error information window pop up: USB Error. Insure USB cable is connected and Driver is
working. Do the following steps:
(a) Click OK, then close main window that shows as Figure 3 and disconnect USB cable.
(b) Check 3.3 V PS#2 and PS#1 voltage on the EVM board.
(c) Disconnect other unsure SMBus connections. Plug in USB cable back to the original EV2400
installation USB port.
(d) Open the bq24715_717_GUI evaluation software. The main window of the software is shown in
Figure 3.
3.2 Charge Regulation and System Load Checks

1. Type in 0xE145 in the Charge Option 0x12 and click the Write button, this disables charging.
2. Connect the Load #2 in series with a current meter (multimeter) to J4 (BAT, GND). Make sure a
voltage meter is connected across J4 (BAT, GND). Turn on power to Load #2. Use the constant
voltage mode. Set the output voltage to 10.5 V for 3 cell bq24715 (-001) setting or 15 V for 4 cell
bq24717 (-002) setting. Enable Load #2 output.
3. Connect the output of the Load #1 in series with a current meter (multimeter) to J4 (SYS, GND). Make
sure a voltage meter is connected across J4 (SYS, GND). Turn on power of Load #1. Set the load
current to 0.5 A ±50 mA but disable the output. The setup is now like Figure 4 for PWR115. Make sure
Ibat = 0 A ±10 mA and Isys = 0 A ±10 mA.
www.ti.com Procedure
Figure 4. Test setup for PWR115
4. Type 3008 (mA) in the Charge Current DAC and click the Write button. This sets the battery charge
current regulation threshold to 3.008 A.
5. Type 8144 in the Charge Option 0x12 and click the Write button, this enables charging.
Measure → Ibat = 3000 mA ±300mA
6. Type 1984 (mA) for (-001) and 2880 (mA) for (-002) in the Input Current 0x3F window and click the
Write button
7. Type 8146 in the Charge Option 0x12 and enable the output of the Load #1.
Measure→ Isys = 500 mA ±50 mA,
Measure → (-001): Iin = 1980 mA ±150 mA, (-002): Iin = 2800 mA ±150 mA
8. Turn off the Load #1.
Measure → Isys = 0 ±100 mA, Ibat = 3000 mA ±300 mA.
9. Set the Load #2 voltage to 8 V ±0.1 V
Measure → Ibat = 384 mA ±100 mA
10. Turn off Load #2
3.3 Equipment Shutdown

Turn off all the power supplies and remove connections to EVM.
PCB Layout Guideline www.ti.com
4 PCB Layout Guideline

The switching node rise and fall times should be minimized for minimum switching loss. Proper layout of
the components to minimize high frequency current path loop is important to prevent electrical and
magnetic field radiation and high-frequency resonant problems. Here is a PCB layout priority list for proper
layout. It is essential that the PCB is laid out according to this specific order.
1. Place the input capacitor as close as possible to switching MOSFET’s supply and ground connections
and use the shortest possible copper trace connection. These parts should be placed on the same
layer of the PCB instead of on different layers and using vias to make this connection.
2. The IC should be placed close to the switching MOSFET’s gate terminals and keep the gate drive
signal traces short for a clean MOSFET drive. The IC can be placed on the other side of the PCB of
switching MOSFETs.
3. Place inductor input terminal as close as possible to the switching MOSFET’s output terminal. Minimize
the copper area of this trace to lower electrical and magnetic field radiation but make the trace wide
enough to carry the charging current. Do not use multiple layers in parallel for this connection.
Minimize parasitic capacitance from this area to any other trace or plane.
4. The charging current sensing resistor should be placed right next to the inductor output. Route the
sense leads connected across the sensing resistor back to the IC in the same layer, close to each
other (minimize loop area) and do not route the sense leads through a high-current path. Place the
decoupling capacitor on these traces next to the IC.
5. Place an output capacitor next to the sensing resistor output and ground.
6. Output capacitor ground connections need to be tied to the same copper that connects to the input
capacitor ground before connecting to system ground.
7. Use a single ground connection to tie charger power ground to charger analog ground. Just beneath
the IC, use analog ground copper pour but avoid power pins to reduce inductive and capacitive noise
coupling.
8. Route the analog ground separately from the power ground. Connect the analog ground and the power
ground separately. Connect the analog ground and power ground together using the power pad as the
single ground connection point, or using a 0-Ω resistor to tie the analog ground to the power ground
(the power pad should tie to the analog ground in this case, if possible).
9. Decoupling capacitors should be placed next to the IC pins and make the trace connection as short as
possible.
10. It is critical that the exposed power pad on the backside of the IC package be soldered to the PCB
ground. Ensure that there are sufficient thermal vias directly under the IC, connecting to the ground
plane on the other layers.
www.ti.com Bill of Materials (BOM) PCB Layout and Schematic
5 Bill of Materials (BOM) PCB Layout and Schematic
5.1 Bill of Materials (BOM)
Table 4. PWR115A BOM

Count
RefDes Value Description Size Part Number MFR
-001 -002
1 1 C1 2.2uF Capacitor, Ceramic, 25V, X7R, 10% 1210 Std Std
0 0 C10 C12 C13 C9 Open Capacitor, Ceramic, 25V, X7R, 10% 0603 Std Std
1 1 C24 470pF Capacitor, Ceramic, 25V, X7R, 10% 0603 Std Std
0 0 C18 C27 Open Capacitor, Ceramic, 25V, [temp], [tol] 1206 Std Std
0 0 C19 Open Capacitor, Ceramic, 25V, X7R, 10% 1206 Std Std
6 6 C21, C5-7 C14-15 0.1uF Capacitor, Ceramic, 25V, X7R, 10% 0603 Std Std
4 4 C2-3 C16-17 10uF Capacitor, Ceramic, 25V, X7R, 10% 1206 Std Std
1 1 C25 0.047uF Capacitor, Ceramic, 25V, X7R, 10% 0603 Std Std
1 1 C26 Open Capacitor, ALUM 220UF 25V 20% SMD 10.3mm (F8) UCL1E221MCL6GS Nichicon
1 1 C28 220uF Capacitor, ALUM 220UF 25V 20% SMD 10.3mm (F8) UCL1E221MCL6GS Nichicon
4 4 C4, C8, C11, C22 1.0uF Capacitor, Ceramic, 25V, X7R, 10% 0603 Std Std
2 2 D1, D2 BAT54-V-G Diode, Schottky, 200-mA, 30-V SOT23 BAT54-V-G Vishay-Liteon
1 1 J1 ED120/2DS Terminal Block, 2-pin, 15-A, 5.1mm 0.40 x 0.35 inch ED120/2DS OST
1 1 JP1 PEC02SAAN Header, Male 2-pin, 100mil spacing, 0.100 inch x 2 PEC02SAAN Sullins
1 1 L1 3.3uH Inductor, SMT, 9.2A, 16.5milliohm 8.2X8.6 mm IHLP3232DZER3R3M01 Vishay
1 1 Q1 CSD87312Q3E MOSFET, Dual NexFET Power, 30 Vds QFN-8 POWER CSD87312Q3E TI
2 2 Q2-3 CSD17308Q3 MOSFET, Fast Switching, NChan, 30V, 12A, 30millohm PWRPAK 1212 CSD17308Q3 TI
1 1 Q4 CSD25401Q3 MOSFET, PChan, -20V, 60A, 8.7 milliOhm QFN3.3X3.3mm CSD25401Q3 TI
1 1 Q5 BSS138W-7-F MOSFET, Nch, 50V, 200mA, SOT323 BSS138W-7-F Diodes
0 0 Q6 Open MOSFET, P Chan, 20V, 60 A, 1.9 mOhm SO-power SI7141DP Vishay
2 2 R1 R3 3.9 Resistor, Chip, 0.5W, 5% 1210 Std Std
0 0 R10 Open Resistor, Metal Film, 1/4 watt, 1% 1206 Std Std
0 0 R12, R13 Open Resistor, Chip, 1/16W, 1% 0603 Std Std
1 1 R14 1.00M Resistor, Chip, 1/16W, 1% 0603 Std Std
1 1 R15 3.01M Resistor, Chip, 1/16W, 1% 0603 Std Std
2 2 R16 R18 4.02k Resistor, Chip, 1/10W, 1% 0603 Std Std
Bill of Materials (BOM) PCB Layout and Schematic www.ti.com
Table 4. PWR115A BOM (continued)

Count
RefDes Value Description Size Part Number MFR
-001 -002
1 1 R17 4.7 Resistor, Chip, 1/16W, 1% 0603 Std Std
3 3 R19 R21 R23 10.0k Resistor, Chip, 1/16W, 1% 0603 Std Std
2 2 R2 R11 0.01 Resistor, Chip, 1/2W, 1% 1206 CSRF1206FT10L0 Stackpole
1 1 R20 10 Resistor, Metal Film, 1/4 watt, 1% 1206 Std Std
2 2 R22 R25 100k Resistor, Chip, 1/16W, 1% 0603 Std Std
1 1 R24 15 Resistor, Chip, 1/16W, 1% 0603 Std Std
1 1 R26 348k Resistor, Chip, 1/16W, 1% 0603 Std Std
4 4 R4, R7, R8, R9 0 Resistor, Chip, 1/16W, 1% 0603 Std Std
1 1 R5 430K Resistor, Chip, 1/16W, 1% 0603 Std Std
1 1 R6 66.5K Resistor, Chip, 1/16W, 1% 0603 Std Std
0 0 TP11 DNI Adaptor, 3.5-mm probe clip ( or 131-5031-00) 0.200 inch 131-4244-00 Tektronix
11 11 TP1-5 TP10, TP13- 5002 Test Point, White, Thru Hole Color Keyed 0.100 x 0.100 inch 5002 Keystone
16, TP18
1 1 TP17 5001 Test Point, Black, Thru Hole Color Keyed 0.100 x 0.100 inch 5001 Keystone
0 0 TP6-9 TP12 Open Test Point, 0.020 Hole STD
1 0 U1 BQ24715RGR IC, SMBus Controlled 2-3S NVDC-1 Charge Controller with N-Ch VQFN BQ24715RGR TI
MOSFET Selector and Current Monitoring
0 1 U1 BQ24717RGR IC, SMBus Controlled 3-4S NVDC-1 Charge Controller with N-Ch VQFN BQ24717RGR TI
MOSFET Selector and Current Monitoring
1 1 U2 TPS3803-01 Single Voltage Detector SC-70-5 TPS3803-01DCK TI
4 4 SJ61A4 Bump on Hemisphere, Black; Note 5 0.375x0.311 SJ61A4 3M
1 1 — 929950-00 Shunt, 100-mil, Black 0.100 929950-00 3M
1 1 — Label 1.25 x 0.25 inch THT-13-457-10 Brady
1 1 — PWR115 2.5x2.5inch 4 layer 2oz. PCB 2.5x2.5inch PCB Any
Notes: 1. These assemblies are ESD sensitive, ESD precautions shall be observed.
2. These assemblies must be clean and free from flux and all contaminants. Use of no clean flux is not acceptable.
3. These assemblies must comply with workmanship standards IPC-A-610 Class 2.
4. Ref designators marked with an asterisk ('**') cannot be substituted. All other components can be substituted with equivalent MFG's components.
5. Install after final wash on bottom corners of PCB.
Table 1
Assembly No. Text
PWR115-001 bq24715EVM-115
PWR115-002 bq24717EVM-115
5.2 Schematic
BSS138W-7-F
Reverse
Q5
Input
Protection PH
R14 R15
TP11
1.00M 3.01M
1 1
Vin = 18-24V
J1 Q1
1 CSD87312Q3E
DCIN SYS
D D
GND 2 R2 0.01 TP7 C18
C8 CSD17308Q3A + C28 + C26
C1 R4 C2 C3
1.0uF Q2
220uF 1
2.2uF 0 C10 10uF 10uF 1
1
C6 0.1uF TP6 1 TP12
R1 R3 C20
1 J4
G S C22
2200pF
C21 C7 1 L1 1 0-13.05V @ 8A
3.9 3.9 R5 CSD25401Q3 SYS
R17 0.1uF 0.1uF R11
430k VCC 1.0uF C25 0.047uF 3
4.7 1 2
2 PGND
1 3.3uH 0.01 1
ACDET C5 TP9 R24 D2 BAT
Q3 C12 C16 C17 C19 Q4 1
0.1uF 15 BAT54-V-G C27
C4 10uF
1 10uF
1
21
REGN
1
20
19
18
17
16
1 1 R12
R6 1.0uF C24 R10 1
C11 1
HIDRV
REGN
BTST
PHASE
66.5k C14 0.1uF
VCC
BAT54C-V-G 470pF 1 Q6
PWPD
R18 1.0uF 1 1
D1 4.02k CMSRC TP8
1 15 1
ACN LODRV 1 R13
R20 R16 2 CSD17308Q3A
U1 14 C13 C15
ACDRV 4.02k ACP GND
VCC 3 BQ24715RGR/BQ24717RGR 1
13 R8
10.0 CMSRC SRP 1
0.1uF
4 12 1
ACDRV SRN 0 1
R9
5 11
3V3 ACOK BATDRV
R19 0
/BATDRV
ACDET
10.0k R7
CELL
IOUT
SDA
SCL
ACOK 0
JP1
10
6
7
8
9
REGN
C9
IOUT
R22 SYS
4
Cell CELL 1 100k
TPS3803DCK
3 R26
ACOK ACOK 3 4
3V3 RST VDD 348k 2
2
IOUT IOUT C23 2
GND
1 R23 R21
3V3 3V3 100pF 1 5
10.0k 10.0k CELL NC SNS/NC
J3
SCL TPS3803DCK
SCL U2
3
SDA R25
2 2
100k
GND SDA
1
J2
APPLICATION CIRCUIT
TP1 TP14 TP2 TP3

CMSRC ACOK ACDRV ACDET
TP13 TP5 TP10 TP18 If the system voltage drops lower than (R26 / R25 + 1) x 1.266 V (5.5 V for values on EVM schematic),
U2 pulls the Cell pin on U1 low and resets registers 0x14 (Charge Current),
1 Not Installed IOUT SDA SCL CELL
2
0x15 (Mac Charge Voltage) and 0x12 bit[1] = 0 (IDPM); bit[5] = 0 (LEARN).
TP16 TP17 TP15 TP4

/BATDRV REGN VCC
TEST POINTS
Figure 5. bq2471x Schematic
5.3 Layouts
Figure 6. Assembly Layer
Figure 7. Top Layer
Figure 8. Layer 2
Figure 9. Layer 3
Figure 10. Bottom Layer
SLUUA74 – January 2013 19
Submit Documentation Feedback
EVALUATION BOARD/KIT/MODULE (EVM) ADDITIONAL TERMS
Texas Instruments (TI) provides the enclosed Evaluation Board/Kit/Module (EVM) under the following conditions:
The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user indemnifies TI from all claims
arising from the handling or use of the goods.
Should this evaluation board/kit not meet the specifications indicated in the User’s Guide, the board/kit may be returned within 30 days from
the date of delivery for a full refund. THE FOREGOING LIMITED WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY SELLER TO
BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH
ABOVE, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES.
Please read the User's Guide and, specifically, the Warnings and Restrictions notice in the User's Guide prior to handling the product. This
notice contains important safety information about temperatures and voltages. For additional information on TI's environmental and/or safety
programs, please visit www.ti.com/esh or contact TI.
No license is granted under any patent right or other intellectual property right of TI covering or relating to any machine, process, or
combination in which such TI products or services might be or are used. TI currently deals with a variety of customers for products, and
therefore our arrangement with the user is not exclusive. TI assumes no liability for applications assistance, customer product design,
software performance, or infringement of patents or services described herein.
REGULATORY COMPLIANCE INFORMATION

As noted in the EVM User’s Guide and/or EVM itself, this EVM and/or accompanying hardware may or may not be subject to the Federal
Communications Commission (FCC) and Industry Canada (IC) rules.
For EVMs not subject to the above rules, this evaluation board/kit/module is intended for use for ENGINEERING DEVELOPMENT,
DEMONSTRATION OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end product fit for general consumer
use. It generates, uses, and can radiate radio frequency energy and has not been tested for compliance with the limits of computing
devices pursuant to part 15 of FCC or ICES-003 rules, which are designed to provide reasonable protection against radio frequency
interference. Operation of the equipment may cause interference with radio communications, in which case the user at his own expense will
be required to take whatever measures may be required to correct this interference.
General Statement for EVMs including a radio
User Power/Frequency Use Obligations: This radio is intended for development/professional use only in legally allocated frequency and
power limits. Any use of radio frequencies and/or power availability of this EVM and its development application(s) must comply with local
laws governing radio spectrum allocation and power limits for this evaluation module. It is the user’s sole responsibility to only operate this
radio in legally acceptable frequency space and within legally mandated power limitations. Any exceptions to this are strictly prohibited and
unauthorized by Texas Instruments unless user has obtained appropriate experimental/development licenses from local regulatory
authorities, which is responsibility of user including its acceptable authorization.
For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant
Caution
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.
FCC Interference Statement for Class A EVM devices

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his own expense.
FCC Interference Statement for Class B EVM devices
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
For EVMs annotated as IC – INDUSTRY CANADA Compliant
This Class A or B digital apparatus complies with Canadian ICES-003.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
Concerning EVMs including radio transmitters
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Concerning EVMs including detachable antennas

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain
approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should
be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
This radio transmitter has been approved by Industry Canada to operate with the antenna types listed in the user guide with the maximum
permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain
greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Cet appareil numérique de la classe A ou B est conforme à la norme NMB-003 du Canada.
Les changements ou les modifications pas expressément approuvés par la partie responsable de la conformité ont pu vider l’autorité de
l'utilisateur pour actionner l'équipement.
Concernant les EVMs avec appareils radio
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Concernant les EVMs avec antennes détachables
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain
maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à
l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente
(p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.
Le présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le manuel
d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans
cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
【Important Notice for Users of this Product in Japan】
】
This development kit is NOT certified as Confirming to Technical Regulations of Radio Law of Japan
If you use this product in Japan, you are required by Radio Law of Japan to follow the instructions below with respect to this product:
1. Use this product in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal Affairs and
Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for Enforcement of Radio Law of
Japan,
2. Use this product only after you obtained the license of Test Radio Station as provided in Radio Law of Japan with respect to this
product, or
3. Use of this product only after you obtained the Technical Regulations Conformity Certification as provided in Radio Law of Japan with
respect to this product. Also, please do not transfer this product, unless you give the same notice above to the transferee. Please note
that if you could not follow the instructions above, you will be subject to penalties of Radio Law of Japan.
Texas Instruments Japan Limited
(address) 24-1, Nishi-Shinjuku 6 chome, Shinjuku-ku, Tokyo, Japan
http://www.tij.co.jp
【ご使用にあたっての注】
本開発キットは技術基準適合証明を受けておりません。
本製品のご使用に際しては、電波法遵守のため、以下のいずれかの措置を取っていただく必要がありますのでご注意ください。
1. 電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用いただく。
2. 実験局の免許を取得後ご使用いただく。
3. 技術基準適合証明を取得後ご使用いただく。
なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。
　　　上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。
日本テキサス・インスツルメンツ株式会社
東京都新宿区西新宿６丁目２４番１号
西新宿三井ビル
http://www.tij.co.jp
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
EVALUATION BOARD/KIT/MODULE (EVM)
WARNINGS, RESTRICTIONS AND DISCLAIMERS
For Feasibility Evaluation Only, in Laboratory/Development Environments. Unless otherwise indicated, this EVM is not a finished
electrical equipment and not intended for consumer use. It is intended solely for use for preliminary feasibility evaluation in
laboratory/development environments by technically qualified electronics experts who are familiar with the dangers and application risks
associated with handling electrical mechanical components, systems and subsystems. It should not be used as all or part of a finished end
product.
Your Sole Responsibility and Risk. You acknowledge, represent and agree that:
1. You have unique knowledge concerning Federal, State and local regulatory requirements (including but not limited to Food and Drug
Administration regulations, if applicable) which relate to your products and which relate to your use (and/or that of your employees,
affiliates, contractors or designees) of the EVM for evaluation, testing and other purposes.
2. You have full and exclusive responsibility to assure the safety and compliance of your products with all such laws and other applicable
regulatory requirements, and also to assure the safety of any activities to be conducted by you and/or your employees, affiliates,
contractors or designees, using the EVM. Further, you are responsible to assure that any interfaces (electronic and/or mechanical)
between the EVM and any human body are designed with suitable isolation and means to safely limit accessible leakage currents to
minimize the risk of electrical shock hazard.
3. You will employ reasonable safeguards to ensure that your use of the EVM will not result in any property damage, injury or death, even
if the EVM should fail to perform as described or expected.
4. You will take care of proper disposal and recycling of the EVM’s electronic components and packing materials.
Certain Instructions. It is important to operate this EVM within TI’s recommended specifications and environmental considerations per the
user guidelines. Exceeding the specified EVM ratings (including but not limited to input and output voltage, current, power, and
environmental ranges) may cause property damage, personal injury or death. If there are questions concerning these ratings please contact
a TI field representative prior to connecting interface electronics including input power and intended loads. Any loads applied outside of the
specified output range may result in unintended and/or inaccurate operation and/or possible permanent damage to the EVM and/or
interface electronics. Please consult the EVM User's Guide prior to connecting any load to the EVM output. If there is uncertainty as to the
load specification, please contact a TI field representative. During normal operation, some circuit components may have case temperatures
greater than 60°C as long as the input and output are maintained at a normal ambient operating temperature. These components include
but are not limited to linear regulators, switching transistors, pass transistors, and current sense resistors which can be identified using the
EVM schematic located in the EVM User's Guide. When placing measurement probes near these devices during normal operation, please
be aware that these devices may be very warm to the touch. As with all electronic evaluation tools, only qualified personnel knowledgeable
in electronic measurement and diagnostics normally found in development environments should use these EVMs.
Agreement to Defend, Indemnify and Hold Harmless. You agree to defend, indemnify and hold TI, its licensors and their representatives
harmless from and against any and all claims, damages, losses, expenses, costs and liabilities (collectively, "Claims") arising out of or in
connection with any use of the EVM that is not in accordance with the terms of the agreement. This obligation shall apply whether Claims
arise under law of tort or contract or any other legal theory, and even if the EVM fails to perform as described or expected.
Safety-Critical or Life-Critical Applications. If you intend to evaluate the components for possible use in safety critical applications (such
as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, such as devices
which are classified as FDA Class III or similar classification, then you must specifically notify TI of such intent and enter into a separate
Assurance and Indemnity Agreement.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265

Smbus Controlled Nvdc-1 Charge Controller, N-CH Mosfet Selector and Current Monitor

Uploaded by

Copyright:

Available Formats

Smbus Controlled Nvdc-1 Charge Controller, N-CH Mosfet Selector and Current Monitor

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Smbus Controlled Nvdc-1 Charge Controller, N-CH Mosfet Selector and Current Monitor

Uploaded by

Copyright:

Available Formats

User's Guide

SLUUA74 – January 2013

SMBus Controlled NVDC-1 Charge Controller, N-CH

1.2 I/O Descriptions

Table 1. I/O Descriptions

Table 2. Recommended Operating Conditions

2.2 Equipment Setup

Table 3. EV2400 and bq24715 EVM Connections

Figure 1. Connections of the EV2400 Kit

(I) If JP1 is not installed, install the jumper.

Figure 2. Original test setup for PWR115 (bq24715 EVM)

Figure 3. a) bq24715 GUI Interface Window; b) bq24717 GUI Interface Window

3.1 Power-up and Initial Checks

3.1.2 Turn on PS#1

3.1.3 Verify the Following Parameters

3.1.4 Default Parameters Settings

3.2 Charge Regulation and System Load Checks

Figure 4. Test setup for PWR115

3.3 Equipment Shutdown

4 PCB Layout Guideline

5 Bill of Materials (BOM) PCB Layout and Schematic

5.1 Bill of Materials (BOM)

Table 4. PWR115A BOM

Table 4. PWR115A BOM (continued)

TP1 TP14 TP2 TP3

TP16 TP17 TP15 TP4

Figure 5. bq2471x Schematic

Figure 6. Assembly Layer

Figure 7. Top Layer

Figure 10. Bottom Layer

REGULATORY COMPLIANCE INFORMATION

For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant

FCC Interference Statement for Class A EVM devices

This Class A or B digital apparatus complies with Canadian ICES-003.

Concerning EVMs including radio transmitters

Concerning EVMs including detachable antennas

Cet appareil numérique de la classe A ou B est conforme à la norme NMB-003 du Canada.

Concernant les EVMs avec appareils radio

Concernant les EVMs avec antennes détachables

You might also like