Página 1 de 5

PT 1 MERKEL PT 1 Low Friction Wiper

Low friction wiper consisting of one profile ring with a
sealing edge and a wiper edge, as well as two O-Rings as
pre-load components. A wiper for improvement of overall
tightness, PT 1 is fitted preferably in combination with our
rod seals. We recommend a bore hold for relieving Max. Temp (F°): 212
pressure. No pressure release is needed for these seals
with a good pump-back action. Where there is a
combination of seals without sufficient pump-back Speed (ft/s): 16
capability a pressure-relieving hole is required.

PT 2 MERKEL PT 2 Low Friction Wiper

Low friction wiper consisting of one profile ring with a
sealing edge and a wiper edge, as well as two O-Rings as
sealing and pre-load components. A wiper for
Max. Temp (F°): 212
improvement of overall tightness. PT 2 is fitted mainly in
combination with our rod seals OMS-S. A pressure
relieving hold provided between seal and wiper. Speed (ft/s): 15

P6 MERKEL P 6 Wiper
Single-acting elastomeric rod wiper with support
components. NBR rod wiper which finds its main use with
Max. Temp (F°): 212
large diameters.
Speed (ft/s): 6

P 7 Wiper MERKEL P7 Wiper

Single-acting rod wiper made from Polyurethane with
integrated metal retainer. PUR wiper for axial-accessible
Max. Temp (F°): 212
housings.
Speed (ft/s): 6

PU 7 MERKEL PU 7 Press Fit Wiper

Polyurethane rod wiper with integrated metal retainer
designed for axial-accessible housings.
Max. Temp (F°): 230
Speed (ft/s): 6

PU 10 MERKEL PU 10 Wiper
Single-acting rod wiper made from Polyurethane with
integrated metal retainer.
Max. Temp (F°): 230
Speed (ft/s): 1.5

MERKEL PU 5 Wiper
 Página 2 de 5

PU 5
Rod wiper with additional static sealing lip and support
components; sealing edge of wiping lip lightly chamfered.
The PU 5 is a single-acting wiper, use even in Max. Temp (F°): 230
standardized housings according to ISO 6195 Type A. Speed (ft/s): 6

PU 11 MERKEL PU 11 Double Acting Wiper

The PU 11 double acting wiper is designed for
improvement of overall tightness and has dimensions
even for standardized housings; according to ISO 6195
type C. The PU 11 is fitted preferably in combination with
our rod seals OMS-MR. The double-lipped wiper can take Max. Temp (F°): 230
pressures up to 1.6 MPa. The lightly rounded sealing edge
wipes dirt away safely and leaves a residual oil film on the
retracting rod. Tightness, working life and friction behavior Speed (ft/s): 6
of the entire system are affected positively.

PU 6 MERKEL PU 6 Wiper
Single-acting wiper with static sealing edge on the outer
diameter. The rod wiper has support components on the
Max. Temp (F°): 230
heel of the wiper, and lightly chamfered wiper lip.
Speed (ft/s): 6

AS SIMRIT Rod Wiper with Metal Casing

This is a single-acting wiper with metal casing and wiper
lip protruding. Designed for protection of cylinders against
ingress of dirt for use mainly in standardised housings. For Max. Temp (F°): 212
new designs we recommend the modern design series. Speed (ft/s): 6

ASOB SIMRIT Rod Wiper with Protruding Wiper Lip

Single-acting wiper for protection of cylinders against
ingress of dirt. For new designs we recommend modern
Max. Temp (F°): 212
design series
Speed (ft/s): 6

AUAS SIMRIT Rod Wiper with Metal Casing

Rod wiper with metal casing, wiper lip protruding and
sharp, cut sealing edge. Single-acting wiper for protection
of cylinders against ingress of dirt, use in standardized Max. Temp (F°): 230
housings, amongst others, according to ISO 6195 Type B.
Speed (ft/s): 6

AUAS R SIMRIT Rod Wiper with Metal Casing

 Página 3 de 5

AUAS R (radius) rod wiper with metal casing, wiper lip

protruding and lightly chamfered sealing edge. Single-
Max. Temp (F°): 230
acting wiper for protection of cylinders against ingress of
dirt, use in standardized housings, amongst others,
Speed (ft/s): 6
according to ISO 6195 Type B.

AUPS SIMRIT Rod Wiper with Metal Casing

Single-acting wiper for protection of cylinders against
ingress of dirt as well as a protective component and
Max. Temp (F°): 230
sealing component for pivoting mountings.
Speed (ft/s): 6

DKB NOK Double Acting Press Fit Dirt Wiper

This seal prevents entry of dust to protect equipment, and
maintains sealing performance of packings. This is a
Max. Temp (F°): 212
double-lip wiper that prevents oil from scraping off.

DKBI NOK Double Acting Press Fit Polyurethane Wiper

This seal prevents entry of dust to protect equipment, and
maintains sealing performance of packings. The double-lip
Max. Temp (F°): 212
wiper prevents oil from scraping off.

DKBY NOK Seal Type DKBY

Pressure (PSI): 5
Max. Temp (F°):
Speed (ft/s):

DKH NOK Press Fit Dirt Wiper

This single-lip seal prevents entry of dust to protect
equipment, and maintains sealing performance of
Max. Temp (F°): 212
packings.

DKI NOK Press Fit Polyurethane Dirt Wiper

This seal prevents entry of dust to protect equipment, and
maintains sealing performance of packings. It's a standard
Max. Temp (F°): 212
type of wiper, with a high dust-proof performance.
 Página 4 de 5

DSI NOK Snap-In Polyurethane Dirt Wiper

This seal prevents entry of dust, and protects equipment
by maintaining sealing performance of the packing. It can
be fitted into an integrated groove. This is a single-lip all Max. Temp (F°): 212
rubber wiper seal.

DWI NOK Press Fit Polyurethane Dirt Wiper

This seal prevents entry of dust to protect equipment, and
maintains sealing performance of packings. The wiper
serves under severe dust conditions such as construction Max. Temp (F°): 212
equipment.

DWIR NOK Press Fit Polyurethane Dirt Wiper

This seal prevents entry of dust to protect equipment, and
maintains sealing performance of packings. The wiper is
excellent in preventing oil scraping off, and in follow-abililty Max. Temp (F°): 212
to the eccentricity.

LBH NOK Snap-In Double Acting NBR Dirt Wiper

This seal prevents entry of dust, and protects equipment
by maintaining sealing performance of the packing. It can
be fitted into an integrated groove. It's a double-lip all Max. Temp (F°): 212
rubber wiper seal that prevents oil scraping off.

LBI NOK Snap-In Double Acting Poly Dirt Wiper

This seal prevents entry of dust, and protects equipment
by maintaining sealing performance of the packing. It can
be fitted into an integrated groove. It's a double-lip all Max. Temp (F°): 212
rubber wiper seal that prevents oil scraping off.

SNAP IN DISOGRIN Closed Housing Rod Wiper with Snap In Mounting

SNAP IN series Rod Wiper for medium duty applications
and simple snap in installation. DISOGRIN 9250 Material
with outstanding wear and tear resistance, ensuring Max. Temp (F°): 300
maximum service life.
Speed (ft/s): 3
 Página 5 de 5

Images Description
Image Image Description
Bull Dozer Manipulators
Fork Lift Buffer Seal
Tractor Valves
Stabiliser Shears
Hydraulic Presses Hydraulic Jacks
Mobile Arms Forging
General Cylinder Heavy Duty Construction
Injection Molding Heavy Duty Applications
Mobile Lifts Rolling Mills
Steel Mill Rotary Seal
Compression Molding Cranes
Marine Applications CNC Machines
DISOGRIN DMRW Rod Wiper

DISOGRIN

The Simrit Group

Freudenberg-NOK
DISOGRIN DMRW Rod Wiper
Features & Benefits

Made from Disogrin 9250 Metal enclosure ensures a

urethane for its superior secure fit in the open
wear and tear resistance housing, preventing expul-
and for its extremely low sion of the wiper even
compression set under extreme conditions

Secondary sealing lip

Wiping edge is engineered is engineered to re-
to exert maxium wiping move residual oil film
force to remove the from rod, helping to
toughest contaminants eliminate leakage

Features & Benefits

♦ The DMRW Wiper is a high performance wiper designed for use in the toughest applications.

♦ The wiping edge of the DMRW Wiper is engineered to remove the toughest dirt and grime from
the rod, thereby keeping your system running clean and at its peak performance.

♦ Secondary sealing edge prevents residual oil film from escaping, helping the sealing system
achieve zero leakage performance.

♦ The DMRW Wiper is made from DISOGRIN 9250, world renowned for its resistance to wear and
tear and for its very low compression set. The result is superior performance and longer operat-
ing life than other urethane wipers.

♦ Press-fit design allows easy installation in an open housing.

♦ Metal enclosure ensures a secure fit in the open housing, preventing expulsion of the wiper even
under harsh conditions. The metal enclosure is bonded to the DISOGRIN 9250 through our
proporietary process to prevent separation.

♦ No adhesion effect on sliding surface, even after a long standstill.

♦ Superior performance over a wide range of temperatures and hydraulic fluids.

Page DMRW-2
DISOGRIN DMRW Rod Wiper
Specification Sheet

Materials Examples of Applications

Wiping Element
Material Polyurethane
Des ignation DISOGRIN D92S
Hardnes s 92 Shore A
Earthmoving Forklift Agriculture
Equipment Equipment

Metal Enclosure
Material Low Carbon Steel
Coating Rus t Inhibitor

Application Limits Cranes Std. Hydraulic

Cylinders
Stabilizers

Pressure Not Applicable

Speed 100 FPM (0.5 m/s)

Medium/Temperature D I S O G RI N D 9 2 S

Hydraulic Oil, HL, HLP -40°F to +230°F*

(-40°C to +110°C) Installed Seal
HFA , HFB Fluids +41°F to +122°F
(+5°C to +50°C)

HFC Fluid -22°F to +104°F

(-30°C to +40°C)

HFD Fluid --

Water +41°F to +104°F

(+5°C to +40°C)

HETG (Rape Seed Oil) -40°F to +230°F*

(-40°C to +110°C)

HEES (Synth. Es ter) -22°F to +140°F

(-30°C to +60°C)
Important Notes
HEPG (Glycol) --

The technical information provided on this

Mineral Oil -40°F to +230°F* specification sheet is for general guidance only
(-40°C to +110°C) and values may vary with the specific param-
eters and other variables of an application. For
*Capable of operating from -65°F to +300°F in a sealing recommendation specific to your
these fluids. Please consult our engineering application, please contact our Engineering
group for details. Department.

Page DMRW-3
DISOGRIN DMRW Rod Wiper
Design Details

L
H

R1 ≤ 1/64"
20°

Chamfered and burr-free

D d

Surface Finish Tolerances

Recommended Surface Finish Tolerances for each diameter based on diam-

eter. Please see size listing for dimensions for
Surface Rmax Ra each part. Please see “Design Tolerance”
Sliding Surface ≤ 100 µ inch ≤ 12 µ inch section for complete details on machine
tolerances.
Groove Bottom ≤ 252 µ inch ≤ 64 µ inch
Groove Sides ≤ 600 µ inch ≤ 120 µ inch Dimension Range Tolerance
+0.000
<3" - 0.003

+0.000
≥ 3" and < 7"
Lead-in Chamfer “C” d
- 0.004

+0.000
≥ 7" and < 10" - 0.005

The lead-in chamfer “C” is determined by the ≥ 10" and < 15"
+0.000
- 0.006
rod seal chosen. Please use the values
+0.001
recommended per the rod seal. < 1.5" - 0.001

+0.001
≥ 1.5" and < 2" - 0.001

+0.001
≥ 2 and < 3.25" - 0.001

+0.001
D ≥ 3.25" and < 5" - 0.001

+0.001
≥ 5" and < 7" - 0.001

+0.001
≥ 7" and < 9" - 0.001

+0.001
≥ 9" and < 15" - 0.001

+0.020
L ≤ 1" - 0.020

Page DMRW-4
DISOGRIN DMRW Rod Wiper
Standard Range L
H
Inch Sizes

D d

Nominal Dims. (inch) d D L

d D H (inch) (inch) (inch) Part No.

1-1/2 2-1/4 7/16 1.500 2.250 0.430 210-016

1-3/4 2-7/16 7/16 1.750 2.437 0.430 210-021
2 2-11/16 7/16 2.000 2.686 0.430 210-026
2-1/4 3 7/16 2.250 2.997 0.430 210-032
2-1/2 3-1/4 7/16 2.500 3.250 0.430 210-039
2-3/4 3-3/4 1/2 2.750 3.750 0.550 210-045
3 4 1/2 3.000 4.000 0.550 210-049
3-1/4 4-1/4 1/2 3.250 4.250 0.550 210-054
3-1/2 4-1/2 1/2 3.500 4.500 0.550 210-060
3-3/4 4-3/4 1/2 3.750 4.750 0.550 210-064
4 5 1/2 4.000 5.000 0.550 210-068
5 6 1/2 5.000 6.000 0.550 210-094
5-3/4 6-3/4 1/2 5.750 6.750 0.550 210-095
6-3/4 7-3/4 1/2 6.750 7.750 0.550 210-090
7 8 1/2 7.000 8.000 0.550 210-092

Page DMRW-5
DISOGRIN MRW Rod Wiper

DISOGRIN

The Simrit Group

Freudenberg-NOK
DISOGRIN MRW Rod Wiper
Features & Benefits

Low carbon steel case Metal enclosure ensures

with rust inhibitor helps a secure fit in the open
prevent premature housing, preventing
corrosion. expulsion of the wiper
even under extreme
conditions.

Made from
Wiping edge is DISOGRIN 9250,
engineered to exert our premium ure-
maximum force to thane, it ensures
keep rod clean and maximum operating
prevent contami- life due to its low
nants from enter- compression set and
ing system. excellent wear and
tear resistance.

Features & Benefits

♦ The MRW is our premium wiper for use with open housings.

♦ Wiper edge is engineered to remove even the toughest dirt and contaminants from the rod,
thereby keeping your system running clean and at its peak performance.

♦ Superior abrasion and wear resistance of DISOGRIN 9250 ensures longer operating life than
other urethane wipers.

♦ No adhesion effect on sliding surface, even after long standstill.

♦ Metal enclosure is designed to securely fit the MRW in an open housing and prevent expulsion of
the wiper under harsh working conditions.

♦ Low compression set of DISOGRIN 9250 means cycle after tough cycle, the MRW Dirt Wiper will
continue to remove contaminants and dirt from the rod.

♦ Effective performance over a wide range of temperatures and fluids.

♦ Can be used effectively in sub-zero environments. Some sizes may be used as link pin seals.

♦ Available in standards inch sizes, up to 8” (150mm) in diameter

Page MRW-2
DISOGRIN MRW Rod Wiper
Specification Sheet

Materials Examples of Applications

Wiping Element
Material Polyurethane
Des ignation DISOGRIN D92S
Hardnes s 92 Shore A
Earthmoving Forklift Agriculture
Equipment Equipment
Metal Enclosure
Material Low Carbon Steel
Coating Rus t Inhibitor

Application Limits Injection Molding

Machines
Std. Hydraulic
Cylinders
Cranes

Pressure Not Applicable

Speed 100 FPM (0.5 m/s)

Medium/Temperature D I S O G RI N D 9 2 S
Stabilizer

Hydraulic Oil, HL, HLP -40°F to +230°F*

(-40°C to +110°C) Installed Seal
HFA , HFB Fluids +41°F to +122°F
(+5°C to +50°C)

HFC Fluid -22°F to +104°F

(-30°C to +40°C)

HFD Fluid --

Water +41°F to +104°F

(+5°C to +40°C)

HETG (Rape Seed Oil) -40°F to +230°F*

(-40°C to +110°C)

HEES (Synth. Es ter) -22°F to +140°F

(-30°C to +60°C)
Important Notes
HEPG (Glycol) --

The technical information provided on this

Mineral Oil -40°F to +230°F* specification sheet is for general guidance only
(-40°C to +110°C) and values may vary with the specific param-
eters and other variables of an application. For
*Capable of operating from -65°F to +300°F in a sealing recommendation specific to your
these fluids. Please consult our engineering application, please contact our Engineering
group for details. Department.

Page MRW-3
DISOGRIN MRW Rod Wiper
Design Details

L
H

R1 ≤ 1/64"
20°

Chamfered and burr-free

D d

Surface Finish Tolerances

Recommended Surface Finish Tolerances for each diameter based on diam-

eter. Please see size listing for dimensions for
Surface Rmax Ra each part. Please see “Design Tolerance”
Sliding Surface ≤ 100 µ inch ≤ 12 µ inch section for complete details on machine
tolerances.
Groove Bottom ≤ 252 µ inch ≤ 64 µ inch
Groove Sides ≤ 600 µ inch ≤ 120 µ inch Dimension Range Tolerance
+0.000
<3"
Lead-in Chamfer “C” - 0.003

+0.000
≥ 3" and < 7" - 0.004
d
+0.000
The lead-in chamfer “C” is determined by the ≥ 7" and < 10" - 0.005
rod seal chosen. Please use the values +0.000
≥ 10" and < 15"
recommended per the rod seal. - 0.006

+0.001
< 1.5" - 0.001

+0.001
≥ 1.5" and < 2" - 0.001

+0.001
≥ 2 and < 3.25" - 0.001

+0.001
D ≥ 3.25" and < 5" - 0.001

+0.001
≥ 5" and < 7" - 0.001

+0.001
≥ 7" and < 9" - 0.001

+0.001
≥ 9" and < 15" - 0.001

+0.015
L ≤ 1" - 0.000

Page MRW-4
DISOGRIN MRW Rod Wiper
Standard Range L
H
Inch Sizes

D d

Nominal Dims. (inch) d D L

d D H (inch) (inch) (inch) Part No.
3/8 11/16 5/32 0.375 0.687 0.156 110-001
1/2 1 1/4 0.500 1.000 0.250 110-002 *
5/8 1-1/8 5/16 0.625 1.125 0.313 110-003 *
3/4 1-1/4 1/4 0.750 1.250 0.250 110-004
3/4 1-1/4 5/16 0.750 1.250 0.313 110-005 *
7/8 1-1/8 5/32 0.875 1.125 0.156 110-006 *
7/8 1-3/8 5/16 0.875 1.375 0.313 110-007
1 1-1/2 5/16 1.000 1.500 0.313 110-008
1-1/8 1-5/8 5/16 1.125 1.625 0.313 110-009 *
1-1/4 1-3/4 1/4 1.250 1.750 0.250 110-010
1-1/4 1-3/4 5/16 1.250 1.750 0.313 110-011 *
1-3/8 1-7/8 5/16 1.375 1.875 0.313 110-012 *
1-1/2 1-7/8 1/4 1.500 1.875 0.250 110-013
1-1/2 2 1/4 1.500 2.000 0.250 110-014
1-1/2 2 5/16 1.500 2.000 0.313 110-015 *
1-1/2 2-1/4 3/8 1.500 2.250 0.375 110-016
1-5/8 2-1/8 1/4 1.625 2.125 0.250 110-017
1-5/8 2-1/8 5/16 1.625 2.125 0.313 110-018
1-3/4 2-1/4 1/4 1.750 2.250 0.250 110-019
1-3/4 2-1/4 5/16 1.750 2.250 0.313 110-020 *
1-3/4 2-7/16 3/8 1.750 2.437 0.375 110-021
1-7/8 2-3/8 5/16 1.875 2.375 0.313 110-022
2 2-1/2 1/4 2.000 2.500 0.250 110-023
2 2-1/2 5/16 2.000 2.500 0.313 110-024 *
2 2-5/8 1/4 2.000 2.625 0.250 110-025
2 2-11/16 3/8 2.000 2.687 0.375 110-026
2-1/8 2-5/8 5/16 2.125 2.625 0.313 110-027
2-3/16 2-11/16 3/8 2.187 2.687 0.375 110-028
2-1/4 2-3/4 1/4 2.250 2.750 0.250 110-029
2-1/4 2-3/4 5/16 2.250 2.750 0.313 110-030 *
2-1/4 2-7/8 1/4 2.250 2.875 0.250 110-031
2-1/4 3 3/8 2.250 3.000 0.375 110-032
2-1/4 3-1/8 1/4 2.250 3.125 0.250 110-033
2-5/16 3-1/8 3/8 2.312 3.125 0.375 110-034

* Metal encased rod wipers which have (*) following the part Page MRW-5
number can also be used as linkage pin grease seals.
DISOGRIN MRW Rod Wiper
Standard Range L
H
Inch Sizes

D d

Nominal Dims. (inch) d D L

d D H (inch) (inch) (inch) Part No.

2-3/8 2-7/8 5/16 2.375 2.875 0.313 110-035

2-3/8 3-1/8 3/8 2.375 3.125 0.375 110-036
2-1/2 3 5/16 2.500 3.000 0.313 110-037
2-1/2 3-1/4 1/4 2.500 3.250 0.250 110-038
2-1/2 3-1/4 3/8 2.500 3.250 0.375 110-039
2-5/8 3-1/8 1/4 2.625 3.125 0.250 110-040
2-5/8 3-1/8 5/16 2.625 3.125 0.313 110-041
2-3/4 3-1/4 5/16 2.750 3.250 0.313 110-042 *
2-3/4 3-1/2 1/4 2.750 3.500 0.250 110-043 *
2-3/4 3-1/2 1/2 2.750 3.500 0.500 110-044
2-3/4 3-3/4 1/2 2.750 3.750 0.500 110-045
2-7/8 3-3/8 5/16 2.875 3.375 0.313 110-046
3 3-1/2 5/16 3.000 3.500 0.313 110-047
3 3-3/4 1/4 3.000 3.750 0.250 110-048 *
3 4 1/2 3.000 4.000 0.500 110-049
3-1/8 3-3/4 5/16 3.125 3.750 0.313 110-050
3-1/4 3-3/4 3/8 3.250 3.750 0.375 110-051
3-1/4 3-7/8 5/16 3.250 3.875 0.313 110-052 *
3-1/4 4 1/4 3.250 4.000 0.250 110-053 *
3-1/4 4-1/4 1/2 3.250 4.250 0.500 110-054
3-3/8 4 5/16 3.375 4.000 0.313 110-055
3-1/2 4 5/16 3.500 4.000 0.313 110-056 *
3-1/2 4-1/8 1/4 3.500 4.125 0.250 110-057
3-1/2 4-1/8 5/16 3.500 4.125 0.313 110-058 *
3-1/2 4-1/4 1/4 3.500 4.250 0.250 110-059
3-1/2 4-1/2 1/2 3.500 4.500 0.500 110-060
3-5/8 4-1/4 5/16 3.625 4.250 0.313 110-061
3-3/4 4-1/2 5/16 3.750 4.500 0.313 110-062 *
3-3/4 4-3/8 5/16 3.750 4.375 0.313 110-063 *
3-3/4 4-3/4 1/2 3.750 4.750 0.500 110-064
3-7/8 4-1/2 5/16 3.875 4.500 0.313 110-065
4 4-5/8 5/16 4.000 4.625 0.313 110-066 *
4 4-3/4 5/16 4.000 4.750 0.313 110-067
4 5 1/2 4.000 5.000 0.500 110-068

* Metal encased rod wipers which have (*) following the part Page MRW-6
number can also be used as linkage pin grease seals.
DISOGRIN MRW Rod Wiper
Standard Range L
H
Inch Sizes

D d

Nominal Dims. (inch) d D L

d D H (inch) (inch) (inch) Part No.

4-1/8 4-3/4 5/16 4.125 4.750 0.313 110-069

4-1/4 4-3/4 5/16 4.250 4.750 0.313 110-070
4-1/4 4-7/8 5/16 4.250 4.875 0.313 110-071
4-1/4 5-1/4 1/2 4.250 5.250 0.500 110-072
4-3/8 5 5/16 4.375 5.000 0.313 110-073 *
4-1/2 5-1/8 5/16 4.500 5.125 0.313 110-074
4-1/2 5-1/4 1/4 4.500 5.250 0.250 110-075
4-1/2 5-1/2 1/4 4.500 5.500 0.250 110-076
4-1/2 5-1/2 5/16 4.500 5.500 0.313 110-077
4-1/2 5-1/2 1/2 4.500 5.500 0.500 110-078
4-3/4 5-3/8 5/16 4.750 5.375 0.313 110-079 *
4-3/4 5-3/4 1/2 4.750 5.750 0.500 110-080
5 5-5/8 1/4 5.000 5.625 0.250 110-081
5 5-3/4 5/16 5.000 5.750 0.313 110-082 *
5-1/4 5-7/8 5/16 5.250 5.875 0.313 110-083
5-1/4 6 5/16 5.250 6.000 0.313 110-084 *
5-1/2 6-1/8 3/8 5.500 6.125 0.375 110-085
5-3/4 6-3/8 3/8 5.750 6.375 0.375 110-086
6 6-5/8 3/8 6.000 6.625 0.375 110-087
6 7 1/2 6.000 7.000 0.500 110-088
6-1/2 7-1/2 5/8 6.500 7.500 0.625 110-089
6-3/4 7-3/4 1/2 6.750 7.750 0.500 110-090
7 7-7/8 5/16 7.000 7.875 0.313 110-091
7 8 1/2 7.000 8.000 0.500 110-092
7-1/4 8-1/4 1/2 7.250 8.250 0.500 110-093

* Metal encased rod wipers which have (*) following the part Page MRW-7
number can also be used as linkage pin grease seals.
DISOGRIN Snap-In Wiper

DISOGRIN

The Simrit Group

Freudenberg-NOK
DISOGRIN Snap-In Wiper
Features & Benefits

Made from DISOGRIN

9250 polyurethane
which offers:
Extremely flexible • High moldulus of
design for easy elasticity
installation • High wear resistance
• Excellent extrusion
resistance
• Low compression set
• Wide temperature
range

Specially designed
wiper lip provides
hard dirt wiping
action to remove
contaminants.

Features & Benefits

♦ Our Snap-In Dirt Wiper is a proven performer in preventing dirt and contaminants from entering
your hydraulic system.

♦ Flexible, snap-in design for easy installation into closed housing.

♦ Superior abrasion and wear resistance of DISOGRIN 9250 urethane ensures longer operating life
than other urethanes.

♦ Low compression set of DISOGRIN 9250 urethane provides effect wiping force, stroke after stroke.

♦ Effective wiping action over a wide range of temperatures and fluids.

♦ Specially designed wiper lip provides hard wiping action.

♦ Recommended for light to medium dirty applications.

♦ Available in standard inch sizes up to 10” (250mm) in diameter.

Page Snap-In-2
DISOGRIN Snap-In Wiper
Specification Sheet

Materials Examples of Applications

Sealing Element
Material Polyurethane
Des ignation DISOGRIN D92S
Hardnes s 92 Shore A
Tailgate Std. Hydraulic Agriculture
Cylinders Cylinders Equipment
The DISOGRIN Snap-in Wiper is typically an
injection molded part. However, for limited
quantities, prototypes or testing, it is also
available through our SimQuick program.
Please contact us for more information.

Application Limits Civil

Engineering
Machine
Tools
Hydraulic
Jacks

Pressure Not Applicable

Speed 100 FPM (0.5 m/s)

Medium/Temperature D I S O G RI N D 9 2 S
Presses
Hydraulic Oil, HL, HLP -40°F to +230°F*
(-40°C to +110°C) Installed Seal
HFA , HFB Fluids +41°F to +122°F
(+5°C to +50°C)

HFC Fluid -22°F to +104°F

(-30°C to +40°C)

HFD Fluid --

Water +41°F to +104°F

(+5°C to +40°C)

HETG (Rape Seed Oil) -40°F to +230°F*

(-40°C to +110°C)

HEES (Synth. Es ter) -22°F to +140°F

(-30°C to +60°C)
Important Notes
HEPG (Glycol) --

The technical information provided on this

Mineral Oil -40°F to +230°F* specification sheet is for general guidance only
(-40°C to +110°C) and values may vary with the specific param-
eters and other variables of an application. For
*Capable of operating from -65°F to +300°F in a sealing recommendation specific to your
these fluids. Please consult our engineering application, please contact our Engineering
group for details. Department.

Page Snap-In-3
DISOGRIN Snap-In Wiper
Design Details

H L

R1 ≤ 1/64"

Chamfered and burr-free

D D1 d

Surface Finish Tolerances

Recommended Surface Finish Tolerances for each diameter based on diam-

eter. Please see size listing for dimensions for
Surface Rmax Ra each part. Please see “Design Tolerance”
Sliding Surface ≤ 100 µ inch ≤ 12 µ inch section for complete details on machine
tolerances.
Groove Bottom ≤ 252 µ inch ≤ 64 µ inch
Groove Sides ≤ 600 µ inch ≤ 120 µ inch Dimension Range Tolerance
+0.000
<3" - 0.003

Lead-in Chamfer “C” ≥ 3" and < 7"

+0.000
- 0.004
d
+0.000
≥ 7" and < 10" - 0.005
The lead-in chamfer “C” is determined by the +0.000
≥ 10" and < 15"
rod seal chosen. Please use the values - 0.006

recommended per the rod seal. < 1.5"

+0.005
- 0.000

+0.007
≥ 1.5" and < 2" - 0.000

+0.008
≥ 2 and < 3.25" - 0.000

+0.009
D ≥ 3.25" and < 5" - 0.000

+0.010
≥ 5" and < 7" - 0.000

+0.011
≥ 7" and < 9" - 0.000

+0.012
≥ 9" and < 15" - 0.000

+0.015
L ≤ 1" - 0.000

Page Snap-In-4
DISOGRIN Snap-In Wiper
Standard Range H L

Inch Sizes h

D D1 d

Nom. Dims. (inch) d D D1 L

d D h H (inch) (inch) (Inch) (Inch) Part No.

1/8 3/8 1/8 3/16 0.125 0.375 0.279 ... 0.335 0.125 006-001
3/16 7/16 1/8 3/16 0.187 0.427 0.341 ... 0.397 0.125 006-002
1/4 1/2 1/8 3/16 0.250 0.500 0.404 ... 0.460 0.125 006-003
5/16 9/16 1/8 3/16 0.312 0.562 0.466 ... 0.522 0.125 006-004
3/8 5/8 1/8 3/16 0.375 0.625 0.529 ... 0.585 0.125 006-005
7/16 11/16 1/8 3/16 0.437 0.687 0.591 ... 0.647 0.125 006-006
1/2 3/4 1/8 3/16 0.500 0.750 0.654 ... 0.710 0.125 006-007
9/16 13/16 1/8 3/16 0.562 0.812 0.716 ... 0.772 0.125 006-008
5/8 7/8 1/8 3/16 0.625 0.875 0.779 ... 0.835 0.125 006-009
11/16 1-1/16 3/16 9/32 0.687 1.062 0.912 ... 1.000 0.187 006-010
3/4 1-1/8 3/16 9/32 0.750 1.125 0.975 ... 1.065 0.187 006-011
13/16 1-3/16 3/16 9/32 0.812 1.187 1.037 ... 1.127 0.187 006-012
7/8 1-1/4 3/16 9/32 0.875 1.250 1.100 ... 1.190 0.187 006-013
15/16 1-5/16 3/16 9/32 0.937 1.312 1.162 ... 1.252 0.187 006-014
1 1-3/8 3/16 9/32 1.000 1.375 1.225 ... 1.315 0.187 006-015
1-1/16 1-7/16 3/16 9/32 1.062 1.437 1.287 ... 1.377 0.187 006-016
1-1/8 1-1/2 3/16 9/32 1.125 1.500 1.350 ... 1.440 0.187 006-017
1-3/16 1-9/16 3/16 9/32 1.187 1.562 1.412 ... 1.500 0.187 006-018
1-1/4 1-5/8 3/16 9/32 1.250 1.625 1.475 ... 1.565 0.187 006-019
1-5/16 1-11/16 3/16 9/32 1.312 1.687 1.537 ... 1.627 0.187 006-020
1-3/8 1-3/4 3/16 9/32 1.375 1.750 1.600 ... 1.690 0.187 006-021
1-1/2 1-7/8 3/16 9/32 1.500 1.875 1.725 ... 1.815 0.187 006-022
1-5/8 2 3/16 9/32 1.625 2.000 1.850 ... 1.940 0.187 006-023
1-3/4 2-1/8 3/16 9/32 1.750 2.125 1.975 ... 2.065 0.187 006-024
1-7/8 2-1/4 3/16 9/32 1.875 2.250 2.100 ... 2.190 0.187 006-025
2 2-1/2 1/4 3/8 2.000 2.500 2.296 ... 2.420 0.250 006-026
2-1/8 2-5/8 1/4 3/8 2.125 2.625 2.421 ... 2.545 0.250 006-027
2-1/8 2-1/2 3/16 9/32 2.125 2.500 2.350 ... 2.440 0.187 006-072
2-1/4 2-3/4 1/4 3/8 2.250 2.750 2.546 ... 2.670 0.250 006-028
2-3/8 2-7/8 1/4 3/8 2.375 2.875 2.671 ... 2.795 0.250 006-029
2-1/2 3 1/4 3/8 2.500 3.000 2.796 ... 2.920 0.250 006-030
2-5/8 3-1/8 1/4 3/8 2.625 3.125 2.921 ... 3.045 0.250 006-031
2-3/4 3-1/4 1/4 3/8 2.750 3.250 3.046 ... 3.170 0.250 006-032
2-7/8 3-3/8 1/4 3/8 2.875 3.375 3.171 ... 3.295 0.250 006-033

Page Snap-In-5
DISOGRIN Snap-In Wiper
Standard Range H L

Inch Sizes h

D D1 d

Nom. Dims. (inch) d D D1 L

d D h H (inch) (inch) (Inch) (Inch) Part No.

3 3-1/2 1/4 3/8 3.000 3.500 3.296 ... 3.420 0.250 006-034
3-1/8 3-5/8 1/4 3/8 3.125 3.625 3.421 ... 3.545 0.250 006-035
3-1/4 3-3/4 1/4 3/8 3.250 3.750 3.546 ... 3.670 0.250 006-036
3-3/8 3-7/8 1/4 3/8 3.375 3.875 3.671 ... 3.795 0.250 006-037
3-1/2 4 1/4 3/8 3.500 4.000 3.796 ... 3.920 0.250 006-038
3-5/8 4-1/4 5/16 15/32 3.625 4.250 3.993 ... 4.150 0.312 006-039
3-3/4 4-3/8 5/16 15/32 3.750 4.375 4.118 ... 4.275 0.312 006-040
3-3/4 4-1/4 1/4 3/8 3.750 4.250 4.046 ... 4.170 0.250 006-041
3-7/8 4-1/2 5/16 15/32 3.875 4.500 4.243 ... 4.400 0.312 006-042
3-7/8 4-3/8 1/4 3/8 3.875 4.375 4.171 ... 4.295 0.250 006-073
4 4-5/8 5/16 15/32 4.000 4.625 4.368 ... 4.525 0.312 006-043
4 4-1/2 1/4 3/8 4.000 4.500 4.296 ... 4.420 0.250 006-044
4-1/8 4-3/4 5/16 15/32 4.125 4.750 4.493 ... 4.650 0.312 006-045
4-1/4 4-7/8 5/16 15/32 4.250 4.875 4.618 ... 4.775 0.312 006-046
4-1/4 4-3/4 1/4 3/8 4.250 4.750 4.546 ... 4.670 0.250 006-047
4-3/8 5 5/16 15/32 4.375 5.000 4.743 ... 4.900 0.312 006-048
4-3/8 4-7/8 1/4 3/8 4.375 4.875 4.671 ... 4.795 0.250 006-049
4-1/2 5-1/4 3/8 9/16 4.500 5.250 4.940 ... 5.130 0.375 006-050
4-5/8 5-3/8 3/8 9/16 4.625 5.375 5.065 ... 5.255 0.375 006-051
4-3/4 5-1/2 3/8 9/16 4.750 5.500 5.190 ... 5.380 0.375 006-052
4-7/8 5-5/8 3/8 9/16 4.875 5.625 5.315 ... 5.405 0.375 006-053
5 5-3/4 3/8 9/16 5.000 5.750 5.440 ... 5.630 0.375 006-054
5-1/4 6 3/8 9/16 5.250 6.000 5.690 ... 5.880 0.375 006-055
5-3/8 6-1/8 3/8 9/16 5.375 6.125 5.815 ... 6.055 0.375 006-056
5-1/2 6-1/4 3/8 9/16 5.500 6.250 5.940 ... 6.130 0.375 006-057
5-5/8 6-3/8 3/8 9/16 5.625 6.375 6.065 ... 6.255 0.375 006-058
5-3/4 6-1/2 3/8 9/16 5.750 6.500 6.190 ... 6.380 0.375 006-059
5-7/8 6-5/8 3/8 9/16 5.875 6.625 6.315 ... 6.505 0.375 006-060
6 6-3/4 3/8 9/16 6.000 6.750 6.440 ... 6.630 0.375 006-061
6-1/4 7 3/8 9/16 6.250 7.000 6.690 ... 6.880 0.375 006-062
6-1/2 7-1/4 3/8 9/16 6.500 7.250 6.940 ... 7.130 0.375 006-063
6-3/4 7-1/2 3/8 9/16 6.750 7.500 7.190 ... 7.380 0.375 006-064
7 8 1/2 3/4 7.000 8.000 7.600 ... 7.800 0.500 006-065
7-1/2 8-1/2 1/2 3/4 7.500 8.500 8.100 ... 8.300 0.500 006-066

Page Snap-In-6
DISOGRIN Snap-In Wiper
Standard Range H L

Inch Sizes h

D D1 d

Nom. Dims. (inch) d D D1 L

d D h H (inch) (inch) (Inch) (Inch) Part No.

8 9 1/2 3/4 8.000 9.000 8.600 ... 8.800 0.500 006-067

8-1/2 9-1/2 1/2 3/4 8.500 9.500 9.100 ... 9.300 0.500 006-068
9 10 1/2 3/4 9.000 10.000 9.600 ... 9.800 0.500 006-069
9-1/2 10-1/2 1/2 3/4 9.500 10.500 10.100 ... 10.300 0.500 006-070
10 11 1/2 3/4 10.000 11.000 10.600 ... 10.800 0.500 006-071

Page Snap-In-7