Service Manual: HCD-DX375

HCD-DX375
SERVICE MANUAL US Model
Ver. 1.1 2006.04
HCD-DX375 is the amplifier, DVD/CD and tuner

section in DAV-DX375.
This system incorporates with Dolby*1 Digital and Dolby Pro Logic (II) Model Name Using Similar Mechanism HCD-DX255
adaptive matrix surround decoder and the DTS*2 Digital Surround
System. Mechanism Type CDM81C-DVBU101
*1 Manufactured under license from Dolby Laboratories. Optical Pick-up Name KHM-310CAB
“Dolby,” “Pro Logic,” and the double-D symbol are trademarks of
Dolby Laboratories.
*2 Manufactured under license from Digital Theater Systems, Inc.
“DTS” and “DTS Digital Surround” are trademarks of Digital
Theater Systems, Inc.
SPECIFICATIONS
AUDIO POWER SPECIFICATIONS Inputs AM tuner section

POWER OUTPUT AND TV, VCR (AUDIO IN) Sensitivity: 450/250 mV Tuning range 530 – 1,710 kHz (with the
TOTAL HARMONIC AUDIO IN Sensitivity: 250/125 mV interval set at 10 kHz)
DISTORTION Outputs (Analog) 531 – 1,710 kHz (with the
(FTC Output Power): FL/FR/SL/SR/C: 84 W/ch Phones Accepts low-and high- interval set at 9 kHz)
3 ohm at 170 - 20,000 Hz, impedance headphones. Antenna (aerial) AM loop antenna (aerial)
0.7 % THD Intermediate frequency 450 kHz
Super Audio CD/DVD system
SW: 160 W 1.5 ohm at 40 -
Laser Semiconductor laser Video section
170 Hz, 0.7 % THD
(Super Audio CD/DVD: Outputs VIDEO: 1 Vp-p 75 ohms
Amplifier section λ = 650 nm) S VIDEO:
Surround mode (reference) RMS output power, 10 % (CD: λ = 790 nm) Y: 1 Vp-p 75 ohms
THD Emission duration:
C: 0.286 Vp-p 75 ohms
Front: 143 W + 143 W continuous
COMPONENT:
(with SS-TS52) Signal format system NTSC
Y: 1 Vp-p 75 ohms
Center*: 143 W Harmonic distortion Less than 0.03 %
PB/CB, PR/CR: 0.7 Vp-p
(with SS-CT51) 75 ohms
Surround*: 143 W + 143
Tuner section
System PLL quartz-locked digital HDMI OUT:
W Type A (19 pin)
(with SS-TS51) synthesizer system
Subwoofer*: 285 W FM tuner section
(with SS-WS52B) Tuning range 87.5 – 108.0 MHz — Continued on next page —
* Depending on the sound field settings and the source,
(100 kHz step)
Antenna (aerial) FM wire antenna (aerial)
there may be no sound output.
Antenna (aerial) terminals 75 ohms, unbalanced
Intermediate frequency 10.7 MHz
SUPER AUDIO CD/DVD RECEIVER

9-887-160-02
Sony Corporation
2006D16-1 Home Audio Division
© 2006.04 Published by Sony Techno Create Corporation
Downloaded from www.Manualslib.com manuals search engine

HCD-DX375
General CAUTION
Power requirements 120 V AC, 60 Hz
Use of controls or adjustments or performance of procedures
Power consumption On: 160 W
Standby: 0.3 W (at the
other than those specified herein may result in hazardous radiation
Power Saving mode) exposure.
Dimensions (approx.) 430 × 86 × 418 mm
(17 × 3 1/4 × 16 3/4 inches)
(w/h/d) incl. projecting Notes on chip component replacement
parts • Never reuse a disconnected chip component.
Mass (approx.) 5.2 kg (11 lb 8 oz) • Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Design and specifications are subject to change
without notice.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 °C
during repairing.
• Do not touch the soldering iron on the same conductor of the
SAFETY CHECK-OUT circuit board (within 3 times).
After correcting the original service problem, perform the following • Be careful not to apply force on the conductor when soldering
safety check before releasing the set to the customer: or unsoldering.
Check the antenna terminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts for AC leakage. UNLEADED SOLDER
Check leakage as described below. Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
LEAKAGE TEST (Caution: Some printed circuit boards may not come printed with
The AC leakage from any exposed metal part to earth ground and the lead free mark due to their particular size)
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes.).
Leakage current can be measured by any one of three methods. : LEAD FREE MARK
Unleaded solder has the following characteristics.
1. A commercial leakage tester, such as the Simpson 229 or RCA • Unleaded solder melts at a temperature about 40 °C higher
WT-540A. Follow the manufacturers’ instructions to use these than ordinary solder.
instruments. Ordinary soldering irons can be used but the iron tip has to be
2. A battery-operated AC milliammeter. The Data Precision 245 applied to the solder joint for a slightly longer time.
digital multimeter is suitable for this job. Soldering irons using a temperature regulator should be set to
3. Measuring the voltage drop across a resistor by means of a about 350 °C.
VOM or battery-operated AC voltmeter. The “limit” indication Caution: The printed pattern (copper foil) may peel away if
is 0.75 V, so analog meters must have an accurate low-voltage the heated tip is applied for too long, so be careful!
scale. The Simpson 250 and Sanwa SH-63Trd are examples • Strong viscosity
of a passive VOM that is suitable. Nearly all battery operated Unleaded solder is more viscou-s (sticky, less prone to flow)
digital multimeters that have a 2 V AC range are suitable. (See than ordinary solder so use caution not to let solder bridges
Fig. A) occur such as on IC pins, etc.
• Usable with ordinary solder
To Exposed Metal
Parts on Set
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
AC
0.15 µF 1.5 k Ω voltmeter
(0.75 V)
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE

WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
2
HCD-DX375
TABLE OF CONTENTS
1. SERVICING NOTE ................................................... 4 6-8. Schematic Diagram – DMB12 Board (1/7) – ................. 41
6-9. Schematic Diagram – DMB12 Board (2/7) – ................. 42
2. GENERAL ................................................................... 11 6-10. Schematic Diagram – DMB12 Board (3/7) – ................. 43
6-11. Schematic Diagram – DMB12 Board (4/7) – ................. 44
3. DISASSEMBLY 6-12. Schematic Diagram – DMB12 Board (5/7) – ................. 45
3-1. Disassembly Flow ........................................................... 14 6-13. Schematic Diagram – DMB12 Board (6/7) – ................. 46
3-2. Case, Front Panel Assy .................................................... 15 6-14. Schematic Diagram – DMB12 Board (7/7) – ................. 47
3-3. FL Board, SW Board ....................................................... 16 6-15. Printed Wiring Board – MAIN Board (Side A) – ............ 48
3-4. JACK Board, LED Board ................................................ 16 6-16. Printed Wiring Board – MAIN Board (Side B) – ............ 49
3-5. DMB12 Board ................................................................. 17 6-17. Schematic Diagram – MAIN Board (1/6) – ................... 50
3-6. I/O Board, Tuner .............................................................. 18 6-18. Schematic Diagram – MAIN Board (2/6) – ................... 51
3-7. SPEAKER Board, D.C. Fan ............................................ 18 6-19. Schematic Diagram – MAIN Board (3/6) – ................... 52
3-8. MAIN Board .................................................................... 19 6-20. Schematic Diagram – MAIN Board (4/6) – ................... 53
3-9. POWER Board ................................................................ 20 6-21. Schematic Diagram – MAIN Board (5/6) – ................... 54
3-10. DVD Mechanism Deck (CDM81C-DVBU101) ............. 21 6-22. Schematic Diagram – MAIN Board (6/6) – ................... 55
3-11. TRAY .............................................................................. 22 6-23. Printed Wiring Board – I/O Board – ............................... 56
3-12. MOTOR Board M761 (LD/ST Motor), 6-24. Schematic Diagram – I/O Board – ................................. 57
M762 (BU U/D Motor) ................................................... 22 6-25. Printed Wiring Boards – PANEL Section – ..................... 58
3-13. BASE UNIT (DVBU101) ................................................ 23 6-26. Schematic Diagram – PANEL Section – ........................ 59
3-14. Optical Pick-up (KHM-310CAB) ................................... 23 6-27. Printed Wiring Board – SPEAKER Board – ................... 60
3-15. Gear (Sub Tray 1), Gear (Sub Tray 2) ............................. 24 6-28. Schematic Diagram – SPEAKER Board – ...................... 60
3-16. Lever Assy ....................................................................... 24 6-29. Printed Wiring Boards – CD MECHANISM Section – . 61
3-17. Stocker Section ................................................................ 25 6-30. Schematic Diagram – CD MECHANISM Section – ..... 62
3-18. Cam (Stocker) .................................................................. 25 6-31. Printed Wiring Board – POWER Board – ....................... 63
3-19. Gear (Stocker 3) .............................................................. 26 6-32. Schematic Diagram – POWER Board – ........................ 64
3-20. Rotary Encoder (MD) ...................................................... 26
3-21. Gear (BU1) ...................................................................... 27 7. EXPLODED VIEWS
7-1. Overall Section ................................................................ 78
4. TEST MODE ............................................................... 28 7-2. Front Panel Section ......................................................... 79
7-3. Chassis Section ................................................................ 80
5. ELECTRICAL ADJUSTMENT ............................. 32 7-4. DVD Mechanism Deck Section-1
(CDM81C-DVBU101) .................................................... 81
7-5. DVD Mechanism Deck Section-2
6. DIAGRAMS
(CDM81C-DVBU101) .................................................... 82
6-1. Block Diagram – RF Section – ....................................... 34
7-6. DVD Mechanism Deck Section-3
6-2. Block Diagram – AMP Section – ................................... 35
(CDM81C-DVBU101) .................................................... 83
6-3. Block Diagram – AUDIO Section – ............................... 36
7-7. Base Unit (DVBU101) .................................................... 84
6-4. Block Diagram – VIDEO Section – ............................... 37
6-5. Block Diagram – POWER Section – .............................. 38
8. ELECTRICAL PARTS LIST .................................. 85
6-6. Printed Wiring Board – DMB12 Board (Side A) – ......... 39
6-7. Printed Wiring Board – DMB12 Board (Side B) – ......... 40
3
HCD-DX375
SECTION 1
SERVICING NOTE
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK Self-diagnosis Function

OR BASE UNIT
(When letters/numbers appear in the
The laser diode in the optical pick-up block may suffer electrostatic display)
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body. When the self-diagnosis function is activated to
During repair, pay attention to electrostatic break-down and also prevent the system from malfunctioning, a 5-
use the procedure in the printed matter which is included in the character service number (e.g., C 13 50) with a
repair parts. combination of a letter and 4 digits appears on
The flexible board is easily damaged and should be handled with the screen and the front panel display. In this
care. case, check the following table.
NOTES ON LASER DIODE EMISSION CHECK C:13:50
The laser beam on this model is concentrated so as to be focused on

the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission, First 3 Cause and/or corrective action
observe from more than 30 cm away from the objective lens. characters of
the service
number
LASER DIODE AND FOCUS SEARCH
1. Open the cover and turn POWER on with no disc inserted. C 13 The disc is dirty.
2. Confirm that the following operation is performed while ,Clean the disc with a soft cloth
observing the objecting lens. C 31 The disc is not inserted correctly.
1) Confirm that laser beam is spread. ,Restart the system, then re-insert
the disc correctly.
2) Up and down motion of the objective lens. (3 times)
E XX To prevent a malfunction, the
(xx is a number) system has performed the self-
DISC TRAY LOCK diagnosis function.
The disc tray lock function for the antitheft of an demonstration ,Contact your nearest Sony
disc in the store is equipped. dealer or local authorized Sony
Setting Procedure : service facility and give the 5-
1. Press the ?/1 button to turn the set on. character service number.
2. Press the [FUNCTION] button to set DVD function. Example: E 61 10
3. Insert a disc.
4. Press the x button and the A button simultaneously for five
When displaying the version
seconds.
5. The message “LOCKED” is displayed and the tray is locked. number on the screen
Releasing Procedure : When you turn on the system, the version
1. Press the x button and the A button simultaneously for five number [VER.X.XX] (X is a number) may
seconds again. appear on the screen. Although this is not a
2. The message “UNLOCKED” is displayed and the tray is malfunction and for Sony service use only,
unlocked. normal system operation will not be possible.
Note 1: When “LOCKED” is displayed, the tray lock is not released by Turn off the system, and then turn on the system
turning power on/off with the ?/1 button. again to operate.
Note 2: Incorrect operations may be performed if the test mode ia not
entered properly. VER.X.XX
In this case, press the ?/1 button to turn the power off, and
retry to enter the test mode.
Note 3: If the disc tray does not open and the message “LOCKED”
appears, press the x button and the A button simultaneously
for seconds or longer.
Then remove your fingers from the above stick and the button.
The message “UNLOCKED” appears for 2 seconds and the disc
tray opens.
Note on DMB12 board replacement

New part of EEP ROM (IC103, IC706) on the DMB12 board cannot be
used. Therefore, if the mounted DMB12 board (A-1148-813-A) is replaced,
exchange new EEP ROM (IC103, IC706) with that used before the
replacement.
4
HCD-DX375
HOW TO OPEN THE DISC TABLE WHEN POWER SWITCH TURNS OFF
tweezers 1 Insert tip of tweezers through the hole

gear
of bottom plate, and roate the gear in
the counter-clockwise direction.
DVD lid
tape
2 Attach an adhesive tape on the DVD LID and draw it out.
Discharge the charged electricity in capacitors to prevent electric shock as follows

When disassembling the machine, be sure to discharge the charged electricity in the following capacitors.
Use a resistor of 800 ohms, 2 Watts for discharging the following capacitors.
POWER board
C903 : 600V
C932, C933, C939, CN902 : 30V
MAIN board
CN3002 : 30 V
MAIN BOARD
*Connect the specified resistor

between black and red leads
CN3002
BLACK
RED
POWER BOARD
CN902
C933 C932
C939
C903
5
HCD-DX375
Fix the capacitors with adhesive agent as follows

Fixing the capacitors with adhesive agent is required by the safety regulation.
Be sure to fix the capacitors with adhesive agent when part or circuit board is replaced.
POWER BOARD
Precaution when replacing the CAP

Please apply the adhesive agent to the BUTTON BASE (PLAY) when replacing the CAP (PLAY) or CAP (FUNC) or CAP (AMS).
Please apply the adhesive agent to the BUTTON BASE (POWER) when replacing the CAP (POWER).
CAP (POWER)
BUTTON BASE (POWER)
SW board
screws
(+BVTP 2.6)
LED board
screws (+BVTP 2.6)
CAP (FUNK) button (disk),

indicator (disk)
CAP (PLAY) JACK board screw (+BVTP 2.6)

CAP (AMS)
BUTTON BASE (PLAY)
6
HCD-DX375
PRECAUTION WHEN INSTALLING A NEW OP UNIT /

PRECAUTION BEFORE UNSOLDERING THE STATIC ELECTRICITY
PREVENTION SOLDER BRIDGE
When installing a new OP unit, be sure to connect the flexible printed circuit board first of all before removing the static
electricity prevention solder bridge by unsoldering. Remove the static electricity prevention solder bridge by unsoldering
after the flexible printed circuit board has already been connected.
(Do not remove nor unsolder the solder bridge as long as the OP unit is kept standalone.)
Precaution on the connector processing of the POWER board.

POWER BOARD
IC941 IC942 IC943
CN901
CN904
12 1 1 3
CN902
AC IN
MAIN BOARD
CN3001
CN506
IC504
CN3002
When re-assembling, leave 30 mm between

harnesses A and B for safety.
After twist the harness once,
install the connector.
MAIN board
harnesses A harnesses B
30mm
POWER board
clamp
7
HCD-DX375
• DMB12 board service position
DMB12 board
Remove the DMB12 board once.

Then create the service position.
DMB12 board
8
HCD-DX375
• POWER board service position
DMB12 board
Remove the DMB12 board and

POWER board once.
POWER board
Front panel assy Connect the flexible cable and

harnesses from the front panel assy.
Inshuration sheet
DMB12 board
POWER board
9
HCD-DX375
• MAIN board service position
DMB12 board, bracket (HDMI) Remove the three connectors of

D.C.fan the SPEAKER board.
MAIN board
SPEAKER board
Remove the DMB12 board ,

bracket (HDMI), D.C.fan and the
MAIN board once.
Front panel assy Connect the flexible cable and

harnesses from the front panel assy.
DMB12 board
D.C.fan
MAIN board
10
HCD-DX375
SECTION 2
GENERAL This section is extracted
from instruction manual.
Front panel
A "/1 (on/standby) (30) G PHONES jack (30)

B Front panel display (93) H VOLUME control (30)
C A (open/close) (30) I AUDIO IN/A.CAL MIC jack (19, 32)
D Disc operation (30) J DISC 1-5 (30)
E FUNCTION (30) K Disc tray (30)
F (remote sensor) (9)
Rear panel
ANTENNA
(DVD ONLY)
AM
OUT
MONITOR OUT R AUDIO IN L
SPEAKER COMPONENT VIDEO OUT TV

VIDEO
Y P B/C B P R/C R COAXIAL

FM 75
S VIDEO
FRONT R FRONT L CENTER WOOFER SUR R SUR L (DVD ONLY) VCR
(DVD ONLY) R AUDIO IN L
A HDMI OUT jack (24) E COAXIAL FM 75Ω jack (13)

B MONITOR OUT (S VIDEO/VIDEO) jacks F VCR (AUDIO IN R/L) jacks (28)
(24) G COMPONENT VIDEO OUT jacks (24)
C TV (AUDIO IN R/L) jacks (28) H SPEAKER jacks (13)
D AM terminal (13)
11
HCD-DX375
Front panel display

About the indications in the front panel display
A Lights up when the HDMI OUT jack is H Lights up during MULTI channel
correctly connected to HDCP (high- playback. (Super Audio CD only) (49)
bandwidth digital content protection) I Lights up when the system outputs
compliant device with HDMI or DVI progressive signals (DVD function
(digital visual interface) input. (24) only). (26)
B Lights up when the time information of J Indicates the selected [SPEAKER
a title or chapter appears in the front FORMATION]. (67)
panel display. (DVD only) (46)
K Lights up when the DYNAMIC BASS is
C Lights up when a station is received. selected. (62)
(Radio only) (58)
L Current surround format (Except for
D Monaural/Stereo effect (Radio only) JPEG and Super Audio CD)
(58)
M Playing status (DVD function only)
E Lights up when the sleep timer is set.
N Displays system’s status such as
(63)
chapter, title, or track number, time
F Lights up when the music or movie information, radio frequency, playing
mode is selected. (Except for JPEG) status, sound field, etc.
(33)
G Lights up when Super Audio CD is
loaded.
12
HCD-DX375
Remote control
ALPHABETICAL ORDER BUTTON DESCRIPTIONS
A–O P–Z [/1 (on/standby) 1 (19, 22, 30,

3)
AMP MENU 7 (22, 32, 61, 63, PICTURE NAVI qh (38, 61) 39, 58)
98) PRESET +/– 8 qd (58) TV [/1 (on/standby) ej (60)
ANGLE 5 (48) PROGRESSIVE qk (26) C/X/x/c/ 3) qg (19, 22, 32, 37,
AUDIO2) ed (44) 57, 64)
SLEEP eh (63)
CLEAR ef (37, 58, 61, 72) REPLAY/
SA-CD/CD ws (49)
ADVANCE wg (30)
D.TUNING wf (58) SOUND FIELD eg (34)
./> qd 8 (30)
DISC SKIP qs (30) SUBTITLE wf (48)
m/M e; wh (36)
DISPLAY 2 (46, 59) THEATRE SYNC wa (61)
/ e; wh (36)
DYNAMIC BASS 3 (62) TOP MENU es (43)
H (play)2) 9 (30, 39, 65)
ENTER1) 4 (19, 22, 32, 37, 57, TUNING +/– wh e; (57)
64) x (stop) wj (31, 39, 64)
TV w; (60)
FUNCTION +/–2) 0 (26, 30, 32, X (pause) wl (31)
TV CH +/–2) 0 (60)
39, 57, 67) DISPLAY3) ea (20, 37, 64,
TV VOL +/– qa (60)
MENU 6 (43, 57) 94)
TV/VIDEO ql (60)
MOVIE/MUSIC wd (33) O RETURN3) qf (38)
VOLUME +/– qa (30, 58, 78)
MUTING wk (30) -/-- ef (60)
Number buttons2) qj (37, 58, 60,
64) 1)The ENTER button is the same
function as the button.
2)
The H, number 5, AUDIO, and
FUNCTION + (TV CH +)
buttons have tactile dots. Use
the tactile dots as references
when operating the system.
3)
After pressing the TV button w;,
you can control the menu on a
Sony TV. On the menu screen,
the DISPLAY button ea
doubles as the MENU button,
and the AMP MENU button 7
double as the TOOLS button.
Note that depending on the
component, you may not be able
to use some or all of the buttons.
13
HCD-DX375
SECTION 3
DISASSEMBLY
3-1. DISASSEMBLY FLOW

• This set can be disassembled in the order shown below.
• The dotted square with arrow ( ) prompts you to move to the next job when all of the works within the dotted square ( ) are
completed.
SET
3-2.CASE, FRONT PANEL ASSY

(Page 15)
3-3.FL BOARD, SW BOARD 3-5.DMB12 BOARD

(Page 16) (Page 17)
3-4.JACK BOARD, LED BOARD

(Page 16) 3-7.SPEAKER BOARD, 3-8.MAIN BOARD
3-6.I/O BOARD, TUNER
(Page 18) D.C. FAN (Page 19)
(Page 18)
3-10.DVD MECHANISM DECK

(CDM81C-DVBU101) 3-9.POWER BOARD
(Page 21) (Page 20)
3-11.TRAY
(Page 22)
3-13.BASE UNIT (DVBU101) 3-12.MOTOR BOARD

(Page 23) M761 (LD/ST MOTOR),
M762 (BU U/D MOTOR)
(Page 22)
3-14.OPTICAL PICK-UP 3-16.LEVER ASSY

(KHM-310CAB) (Page 24)
(Page 23)
3-15.GEAR (SUB TRAY 1), 3-17.STOCKER SECTION 3-20.ROTARY ENCODER (MD)

GEAR (SUB TRAY 2) (Page 25) (Page 26)
(Page 24)
3-18.CAM (STOCKER) 3-21.GEAR (BU1)

(Page 25) (Page 27)
3-19.GEAR (STOCKER 3)
(Page 26)
14
HCD-DX375
Note: Follow the disassembly procedure in the numerical order given.

3-2. CASE, FRONT PANEL ASSY
4 two screws
(CASE3 TP2)
6 five screws
(+BVTP 3 × 8)
7 case
9 wire (flat type)

23core (CN501) 5 two screws
(CASE3 TP2)
8 sheet
qd claw
qa connector (CN312)
3 loading panel qf claw
q; connector (CN3001)
qg front panel assy
qs four screws (+BV3)
When re-assembling, leave 30 mm

tweezers between harnesses A and B for safety.
gear 1 Insert tip of tweezers through the hole
of bottom plate, and roate the gear in
the counter-clockwise direction.
30mm
DVD lid clamp

tape
2 Attach an adhesive tape on the DVD LID and draw it out.
15
HCD-DX375
3-3. FL BOARD, SW BOARD

When reassembling, route the
harness and flexible cable as
shown in the illustration.
9 wire (flat type)

23core (CN801) qg cap (power)
7 connector (CN811)
qf button base
(power)
8 connector (CN805) qd SW board
hold plate (FFC)
qs two screws
(+BVTP 2.6)
q; connector (CNP801)
4 four screws (+BVTP 2.6)
qa FL board
1 rivet
6 three screws (+BVTP 2.6)
5 shield plate (FC) 2 six claws

3 hold plate (FFC)
3-4. JACK BOARD, LED BOARD

9 button (disk)
1 knob (vol)
2 nut
8 five indicators (disk)
6 LED board
5 eight screws (+BVTP 2.6)
q; button (play)
qa four caps (FUNK) 7 button (disk),

indicator (disk)
qs cap (PLAY) 4 JACK board 3 screw (+BVTP 2.6)

qd two caps (AMS)
qf button base (PLAY)
16
HCD-DX375
3-5. DMB12 BOARD
4 connector (CN601)
5 wire (flat type) 5core (CN4302)

8 seven screws (+BV 3)
2 connector (CN201) q; DMB12 board
1 wire (flat type) 11core (CN109) qd bracket HDMI
qs two screws (+BV 3)
9 screw
(+B 3 × 6)
qa two screws
(+BVTP 3 × 8)
17
HCD-DX375
3-6. I/O BOARD, TUNER

7 wire (flat type) 5core(CN202)
8 wire (flat type)11core(CN201) 5 wire (flat type)
3 tuner
9core(CN203)
qa I/O board
4 connector
1 two screws (CN312)
(+BVTT 3 × 6)
6 wire (flat type)
2 wire (flat type) 15core(CN311)
q; Open the
back panel.
9 eight screws
(+BVTP 3 × 8)
3-7. SPEAKER BOARD, D.C. FAN
9 SPEAKER board 7 two screws

(+BV3)
1 connector
(CN3000)
3 D.C. fan
8 two screws
(+BVTP 3 × 8)
2 two screws
(+BVTT 4 × 8)
6 connector
(CN301)
5 connector
(CN302)
4 connector
(CN303)
18
HCD-DX375
3-8. MAIN BOARD

6 connector (CN303)
5 connector (CN303)
3 wire (flat type) 15core (CN601) 7 connector (CN302)

8 connector (CN301)

9 connector (CN3000)
qd wire (flat type) 11core (CN504)

install the connector. qs connector
(CN506) 0 connector (CN3001)
MAIN board
qa connector When re-assembling, leave 30 mm
(CN3002) between harnesses A and B for safety.
POWER board
qf two screws (+BV 3)
30mm
qg HEATSINK A board clamp
qj two screws qh HEATSINK B board

(+BVTP 3 × 10)
When re-assembling, attaching the
two heat radiation sheets on the
IC MAIN board first, and then attach
ql heatsink (AMP) qk screw
the heat sink (AMP).
(+BVTP 3 × 12)
wa eight screws (+BV 3) w; two radiation heatsink (AMP)

sheet
radiation
sheets
wd MAIN board
IC on the
MAIN board
ws clamp
19
HCD-DX375
3-9. POWER BOARD
6 five screws (+PWH 3 × 8)
7 POWER board 4 two screws (+BV 3)
5 shield (H/L)
1 connector (CN506)
2 connector (CN3002)
3 connector (CN901)
When re-assembling, leave 30 mm between

harnesses A and B for safety.

install the connector.
MAIN board
30mm
POWER board clamp
20
HCD-DX375
3-10. DVD MECHANISM DECK (CDM81C-DVBU101)
3 four screws (+BV 3)

4 MD cover
2 Remove the harness and flexible cable.
harness
flexible cable
5 four screws
(+BVTP 3 × 10)
6 DVD mechanism deck

(CDM81C-DVBU101)
21
HCD-DX375
3-11. TRAY
2 two screws
(+BTTP 2.6)
3 bracket 1 two screws

(+BTTP 2.6)
5 tray
3-12. MOTOR BOARD M761 (LD/ST MOTOR), M762 (BU U/D MOTOR)
1 screw
(+BTTP 2.6) 3 screw
(+BTTP 2.6)
2 bracket
4 MOTOR board
5 Remove soldering from the two points.

7 Remove soldering from the two points.
6 M761 (LD/ST MOTOR)
8 M762 (BU U/D MOTOR)
22
HCD-DX375
3-13. BASE UNIT (DVBU101)
1 two floating screws

(+PTPWH2.6)
3 base unit (DVBU101)
2 floating screw
(+PTPWH2.6)
3-14. OPTICAL PICK-UP (KHM-310CAB)
qa insulator
7 insulator screw
3 insulator screw
qs insulator
9 insulator 8 insulator screw
4 insulator screw
qd optical pick-up
(KHM-310CAB)
0 insulator 5
6 holder (310) assy
2 two screws
(+BTP 2.6 × 8)
1 two screws
(+BTP 2.6 × 8)
23
HCD-DX375
3-15. GEAR (SUB TRAY 1), GEAR (SUB TRAY 2)
PRECAUTION DURING GEAR (SUB TRAY 1/2) INSTALLATION 1 five screws

(+PTPWH 2.6 × 8)
Align the marks of the gears as shown in the illustration.

4 three gears
(sub tray 1)
gear (sub tray 2) 2 gear (sub tray 2)
gear (sub tray 1)

3 gear (sub tray 2)
gear (sub tray 2)
3-16. LEVER ASSY
When re-assembling, insert the lever (sub tray)

between the bosses of the shutter (tray).
shutter (tray)
lever (sub tray)
boss
Before re-assembling, align the lever (release)
and the lever (sub tray) with the lever (mode)
as shown in the illustration.
boss
1 screw
dowel dowel (+PTPWH 2.6 × 8)
5 lever (sub tray)
2 shutter (tray)
lever (mode) 7 lever (mode)

lever (release) lever (sub tray)
4
6 lever (release)
3 floating screw
(+PTPWH M2.6)
cam (BU)
Before re-assembling, slide the cam (BU)

in the direction of the arrow.
24
HCD-DX375
3-17. STOCKER SECTION
2 stocker section
1 Rotate the gear (SS3) in the

direction of the arrow.
3-18. CAM (STOCKER)

PRECAUTION DURING CAM (STOCKER) INSTALLATION
Before installing the cams (stocker), fix the gear (stocker 3) in

the manner so that the hole of the gear (stocker 3) should be
aligned with the hole of the chassis located beneath
the gear (stocker 3). Be sure to install the cams (stocker) in 4 lever (SW)
such a way that the grooves of the cams (stocker) face 1 screw
the direction of the arrows. (+PTPWH 2.6 × 8) 2 tension spring (SW)
5 two screws
cam (stocker) (+PTPWH 2.6 × 8)
cam (stocker)
3 hook
gear
7 screw 6 two cams
(stocker 2)
(+PTPWH 2.6 × 8) (stocker)
gear
(stocker 2) hole
8 cam
(stocker)
gear
(stocker 2)
gear (stocker 3) cam (stocker)
25
HCD-DX375
3-19. GEAR (STOCKER 3)
PRECAUTION DURING GEAR (STOCKER 3) INSTALLATION

1 screw
(+PTPWH 2.6 × 8)
Be sure to align the rib of the gear (stocker 3) with the groove
of the rotary encoder.
2 gear (stocker 3)
groove
rib
rotary encoder gear (stocker 3)

(ST U/D encoder) (reverse-side)
3-20. ROTARY ENCODER (MD)
PRECAUTION DURING ROTARY ENCODER (MD) INSTALLATION
Slide the cam (BU) in the direction of the arrow so that the mark
of the gear (BU1) can be seen. Engage the gears while aligning
the mark of the gear (BU1) with the protruding part of the
rotary encoder.
rotary encoder (MD) 1 three screws

(+BTTP 2.6)
protruding part
2 rotary encoder (MD)
mark
cam (BU) gear (BU1)
26
HCD-DX375
3-21. GEAR (BU1)
1 belt (sub tray)
PRECAUTION DURING GEAR (BU1) INSTALLATION
4 screw 2 screw
Before re-assembling, slide the cam (BU) in the direction of (+PTPWH 2.6 × 8) (+PTPWH 2.6 × 8)
the arrow.
Assemble the gear (BU1) in such a manner that the groove
of the cam (BU) is aligned with the rib of the gear (BU1). 3 pulley (BU)
6 screw
(+PTPWH 2.6 × 8)
5 gear (BU2)
cam (BU)
7 gear (BU1)
rib groove
gear (BU1)
27
HCD-DX375
Ver. 1.1 SECTION 4
TEST MODE
3. Disc Tray Lock

Note 1: Regarding the notification symbol “R”
Because the number of the operating buttons of this product The disc tray lock function for the antitheft of an demonstration
are limited, some operations require use of the operating disc in the store is equipped.
buttons of the remote commander, When a specific operation Setting Procedure :
requires use of the operating buttons of the remote 1. Press the ?/1 button to turn the set on.
commander, “R” is added to the specific operating procedure 2. Press the FUNCTION button to set DVD function.
in this manual. Example MENU/NO “R” The MENU/NO 3. Insert a disc.
button of remote commander. 4. Press the x button and the A button simultaneously for five
Note 2: Incorrect operations may be performed if the test mode is
seconds.
not entered properly.
In this case, press the ?/1 button to turn the power off, and 5. The message “LOCKED” is displayed and the tray is locked.
retry to enter the test mode. Releasing Procedure :
1. Press the x button and the A button simultaneously for five
seconds. again.
1. Cold Reset 2. The message “UNLOCKED” is displayed and the tray is
• The cold reset clears all data including preset data stored in unlocked.
the RAM to initial conditions. Execute this mode when Note: When “LOCKED” is displayed, the slot lock is not released by
returning the set to the customers. turning power on/off with the ?/1 button.
Procedure:
1. Press the ?/1 button to turn the power on. 4. DVD Ship Mode
2. Press three buttons x , A and ?/1 simultaneously. • Use this mode when returning the set to the customer after
3. When this button is operated, display as “COLD RESET” for repair.
a while and all of the settings are reset. Procedure:
1. Press the ?/1 button to turn the set on.
2. Panel Test Mode 2. Press the FUNCTION button to set the function “DVD”.
• This mode is used to check the software version, FL, LED 3. Remove all discs, press two buttons x , and . simulta-
and KEY. neously.
4. After a message “MECHA LOCK” is displayed on the
2-1. Display Test Mode fluorescent indicator tube, pull out the AC plug.
Procedure: 5. To exit from this mode, press the ?/1 button to turn the set on.
1. Press the ?/1 button to turn the power on.
2. Press three buttons X , . and A simultaneously. 5. AM Step Change
3. When the display test mode is activated, all segments and LEDs • A step of AM channels can be changed over between 9 kHz
are turned on. and 10 kHz.
4. To exit from this mode, press three buttons X , . and A Procedure:
simultaneously. 1. Press the ?/1 button to turn the set ON.
2. Select the function “TUNER”, and press FUNCTION button
2-2. Version Test Mode to select the BAND “AM”.
Procedure: 3. Press the ?/1 button to turn the set OFF.
1. When the panal test mode is activated, press the . button 4. Press two buttons > and ?/1 simultaneously, and the
and the message “DCX3FD” is displayed, the version test display of fluorescent indicator tube changes to “AM 9 k
mode is activated. STEP” or “AM 10 k STEP”, and thus the channel step is
2. Whenever press the . button, the version is displayed in changed over.
order of NA, MC, SYS, UI, DVD, CDMA, CDMB, ST, TA,
DSP and TM. 6. Volume Test Mode
3. Press the > button and the date of the softwafe production Procedure:
is displayed. 1. Press the ?/1 button to turn the power on.
4. Press the > button again and the version is displayed. 2. Press three buttons . , H and > simultaneously.
5. To exit from this mode, press three buttons X , . and A 3. The message “VOLUME MAX” is displayed, when the
simultaneously. VOLUME control is turned in the dirction of (+).
The message “VOLUME MIN” is displayed, when the
2-3. Key Test Mode VOLUME control is turned in the dirction of (–).
Procedure: 4. To exit from this mode, press the ?/1 button to turn the set
1. When the panel test mode is activated, press the H button, off.
to select the key test mode.
2. To enter the KEY test mode, the fluorecent indicator displays 7. Product Out
“K0 V0”. Each time a button is pressed, “KEY” value This mode moves the optical pick-up to the position durable to
increases. However, once a button is pressed, it is no longer vibration and clears all data including preset data stored in the RAM
taken into account. When all keys are pressed correctly, “K13 to initial conditions. Use this mode when returning the set to the
V0” is displayed. customer after repair.
3. When the VOLUME control is turned in the direction of (+), Procedure:
“V0” is changed to “V1”, then ... “V9”. 1. Press the ?/1 button to turn the power on.
When the VOLUME control is turned in the direction of (–), 2. Press the FUNCTION button to set the function “DVD”.
“V0” is changed to “V9”, then ... “V1”. 3. Remove all discs, and then press three buttons > , A and
4. To exit from this mode, press three buttons X , . and A ?/1 simultaneously.
simultaneously. 4. After the “STANDBY” blinking display finishes, the message
“MECHA LOCK” is displayed on the fluorescent indicator
tube disconnect the AC power plug, then the ship mode is set.
28
HCD-DX375
Ver. 1.1
DVD SECTION 8-4. MIRROR TIME ADJUSTMENT
To enter Mirror Time Adjustment, press 5 “R” button on the remote

[TEST DISC LIST] commander. The screen will appear as below.
Be sure to use the DVD disc that matches the signal standards of
your region. MIRR time Adjust Menu
• CD YEDS-18 (Part No.: 3-702-101-01)
1. CD MIRR time Check:
PATD-012 (Part No.: 4-225-203-01)
2. DVD MIRR time Check:
• DVD SL (Single Layer) 3. Threshold:
NTSC : HLX-503 (Part No.: J-6090-069-A) 4. Save to EEPROM:
HLX-504 (Part No.: J-6090-088-A) 5. Default set MIRR time:
PAL : HLX-506 (Part No.: J-6090-077-A)
• DVD DL (Dual Layer) [Open] Tray open [Close] Tray close
NTSC : HLX-501 (Part No.: J-6090-071-A) [0] Return to previous menu
HLX-505 (Part No.: J-6090-089-A)
PAL : HLX-507 (Part No.: J-6090-078-A) There are five main commands in the Mirr time Adjust menu as
shown in the figure above. The functions of each command are
8-1. GENERAL DESCRIPTION described in the following page.
The Mirror Time and IOP measurement allows you to make 1. CD MIRR time Check
diagnosis and adjustment simply by using the remote commander This command checks the Mirror time value for CD disc.
and monitor TV. The instructions, diagnosis results, etc. are given
on the on-screen display (OSD). 2. DVD MIRR time Check
Be sure to execute the Mirror Time and IOP measurement when a This command checks the Mirror time value for DVD disc.
BU (Base Unit) is replaced.
3. Threshold
8-2. HOW TO ENTER TEST MODE This command displays the threshold value between CD and DVD
mirror time.
While pressing the x and A buttons simultaneously, turn
VOLUME + with the DVD player in power on. 4. Save to EEPROM
The Test Mode starts, then the menu shown below will be displayed This command saves an adjusted mirror time value to the EEPROM.
on the TV screen.
Remocon Diagnosis Menu
5. Default set MIRR time
This command will set CD and DVD mirror time to firmware default
0. External Chip Check value.
1. Servo Parameter Check
2. Drive Manual Operation [Open] / [Close]
3. Emergency History Check Pressing the A button controls the tray for disc change during
4. Version Information mirror time adjustment.
[0] Return to previous menu
Press the 0 “R” button to return to previous menu.
Model Name : DCX3FD_UC
IF-con : Ver. XX.XX (XXXX)
Syscon : Ver. X.XXX 8-4-1. EXECUTING MIRROR TIME ADJUSTMENT
The menu above is the Remocon Diagnosis Menu screen which In order to execute mirror time adjustment, the following standard
consists of six main function. At the bottom of the menu screen, the procedures must be followed.
model name and IF-con version. To enter Mirror Time
Adjustment menu, press button 2 “R” on the remote commander (1) In power on, while pressing the x and A buttons
to enter Drive Manual Operation menu. To exit from the Test Mode, simultaneously, turn VOLUME + .
press the power button on the remote commander. (2) Select “2. Drive Manual Operation”.
8-3. DRIVE MANUAL OPERATION Remocon Diagnosis Menu
The Drive Manual Operation menu consists of five main function. 0. External Chip Check
By pressing 2 “R” button on the remote commander in the Remocon 1. Servo Parameter Check
2. Drive Manual Operation
Diagnosis Menu, the screen will appear as below.
3. Emergency History Check
Drive Manual Operation 4. Version information
1. Servo Control
2. Track/Layer Jump Model Name : DCX3FD_UC
3. Manual Adjustment IF-con : Ver. XX.XX (XXXX)
4. Tray Aging Mode Syscon : Ver. X.XXX
5. MIRR time Adjust
0. Return to Top Menu
29
HCD-DX375
(3) Select “5. MIRR time Adjust”. (14) Confirm the same values are displayed. If it is not same,
return to step 7.
Drive Manual Operation
MIRR time Adjust Menu
1. Servo Control
2. Track/Layer Jump 1. CD MIRR time Check:
3. Manual Adjustment 2. DVD MIRR time Check: XX XX
4. Mecha test mode 3. Threshold:
5. MIRR time Adjust 4. Save to EEPROM:
0. Return to Top Menu 5. Default set MIRR time:
(4) Select “5. Default set MIRR time”. [Open] Tray open [close] Tray close
(15) Push the A button to eject tray.
2. DVD MIRR time Check:
3. Threshold: (16) Take out HLX-504 and insert Test Disc YEDS-18 into
4. Save to EEPROM: tray.
5. Default set MIRR time:
(17) Push the A button to close tray.
[Open] Tray open [Close] Tray close
[0] Return to previous menu (18) Push “1. CD MIRR time check”.
(5) Select “3. Threshold”. (19) Wait for HEX number to display.
(6) Confirm the number. If it is 7D, go to next step. If it is any (20) Confirm the number, if YY is 5A – E8, proceed with next
other value, return to step 4. step. If no, return to 15.
MIRR time Adjust Menu MIRR time Adjust Menu
1. CD MIRR time Check: 1. CD MIRR time Check: yy YY

2. DVD MIRR time Check: 2. DVD MIRR time Check: XX XX
3. Threshold: 7D 3. Threshold:
4. Save to EEPROM: 4. Save to EEPROM:
5. Default set MIRR time: 5. Default set MIRR time:
[Open] Tray open [Close] Tray close [Open] Tray open [close] Tray close
[0] Return to previous menu [0] Return to previous menu
(7) Push the A button to eject tray. (21) Push “4. Save to EEPROM”.
(8) Insert Test Disc HLX-504 into tray. (22) Confirm the same values are displayed. If it is not the
same, return to step 15.
(10) Push “2. DVD MIRR time Check”.
1. CD MIRR time check: YY YY
2. DVD MIRR time check: XX XX
(11) Wait for HEX number to display.
3. Threshold:
4. Save to EEPROM:
(12) Confirm the number, if XX is 28 – 70, proceed with next 5. Default set MIRR time:
step. If no, return to 8.
[Open] Tray open [close] Tray close
MIRR time Adjust Menu [0] Return to previous menu

2. DVD MIRR time Check: xx xx (23) Push the A button to eject tray.
3. Thereshold:
4. Save to EEPROM: (24) Remove Test Disc YEDS-18 from tray.
5. Default set MIRR time:
[Open] tray open [close] Tray close
[0] Return to previous menu (26) Press the 0 “R” button to the Drive Manual Operation menu.
(13) Push “4. Save to EEPROM”. (27) Press the 0 “R” button to return to the Remocon Diagnosis
Menu.
(28) Press the ?/1 button to switch OFF set.
30
HCD-DX375
Ver. 1.1
8-5. EXECUTING IOP MEASUREMENT (5) Wait until a hexadecimal number appear.
Manual Adjust
In order to execute mirror time adjustment, the following standard
procedures must be followed. 1. Track Balance Adjust:
2. Track Gain Adjust:
(1) In standby mode, while pressing the x and A buttons 3. Focus Balance Adjust:
simultaneously, turn VOLUME + . 4. Focus Gain Adjust:
5. Eq Boost Adjust:
Remocon Diagnosis Menu 6. Iop. 5B:
7. TRV. Level:
0. External Chip Check 8. S curve(FE) Level:
1. Servo Parameter Check 9. RFL(PI) Level:
2. Drive Manual Operation 0. MIRR Time:
3. Emergency History Check
4. Version information Change Value
Model Name : DCX3FD_UC

IF-con : Ver. XX.XX (XXXX) (6) Convert each data from hexadecimal to decimal using
Syscon : Ver. X.XXX conversion table.
(2) Select “2. Drive Manual Operation” by pressing the 2 “R” (7) Substract between these two values.
button on the remote commander. The screen will appear as
below. (8) If the remainder is smaller than 93 (decimal), then it is
OK. However if the value is higher than 93, then the BU is
Drive Manual Operation defective and need to be change.
1. Servo Control (9)Press the RETURN “R” button to return back to previous
2. Track/Layer Jump menu.
3. Manual Adjustment
4. Tray Aging Mode
5. MIRR time adjust (10) Press the 0 “R” button to return to Top Menu and power
0. Return to top Menu OFF the DVD Player.
(3) Select “3. Manual Adjustment” by pressing the 3 “R” button

on the remote commander. The screen will appear as below.
Manual Adjust
1. Track Balance Adjust:

2. Track Gain Adjust:
3. Focus Balance Adjust:
4. Focus Gain Adjust:
5. Eg boost Adjust:
6. Iop:
7. TRV. Level:
8. S curve(FE) Level:
9. RFL(PI) Level:
0. MIRR Time:
o O Change Value
[RETURN] Return to previous menu
(4) Select Iop by pressing the 6 “R” button on the remote

commander.
31
HCD-DX375
SECTION 5
ELECTRICAL ADJUSTMENT
DVD SECTION Checking Location: DMB12 board (Side A)
DMB12 BOARD (SIDE A)

When the base unit is replaced, perform the adjustment and the
measurement as shown below in this order.
1) MIRROR TIME ADJUSTMENT (See page 29)

HDMI OUT
2) EXECUTING IOP MEASUREMENT (See page 31) (DVD ONLY)
[TEST DISC LIST]

Be sure to use the DVD disc that matches the signal standards of IC101
your region.
• CD
YEDS-18 (Part No.: 3-702-101-01)
PATD-012 (Part No.: 4-225-203-01)
• DVD SL (Single Layer) IC201
NTSC : HLX-503 (Part No.: J-6090-069-A) CN105 Pin 3 (GND)
HLX-504 (Part No.: J-6090-088-A) 1
CN105
CN105 Pin 6 (RFMON) 3
PAL : HLX-506 (Part No.: J-6090-077-A) 6
• DVD DL (Dual Layer)

NTSC : HLX-501 (Part No.: J-6090-071-A)
OPTICAL PICK-UP
HLX-505 (Part No.: J-6090-089-A) BLOCK
SPINDLE MOTOR
SLED MOTOR
(KHM-310CAB)
PAL : HLX-507 (Part No.: J-6090-078-A)
[RF Level Check]

Connection:
oscilloscope
DMB12 board
CN105 pin 6 (RFMON) +
CN105 pin 3 (GND) –
Procedure:
1. Connect an oscilloscope to CN105 pin 6 (RFMON) and
CN105 pin 3 (GND) on the DMB12 board.
2. Turn the power on.
3. Insert the CD test disc (refer to the TEST DISC LIST), and
press the H button to play the disc back.
4. Confirm that oscilloscope waveform is clear and check RF
signal level is correct or not.
Note: A clear RF signal waveform means that the shape “◊” can be
clearly distinguished at the center of the waveform.
5. Eject the CD disc, and insert the DVD SL test disk (refer to
the TEST DISC LIST), and press the H button to play the
disc back.
RF signal waveform VOLT/DIV: 200 mV

TIME/DIV: 500 ns
level: 0.57 to 1.1 Vp-p (CD)

0.58 to 1.23 Vp-p (DVD)
32
HCD-DX375
SECTION 6
DIAGRAMS
• Circuit Boards Location
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed in each block.)
For Schematic Diagrams. For Printed Wiring Boards.
Note: Note:
• All capacitors are in µF unless otherwise noted. (p: pF) • X : parts extracted from the component side.
50 WV or less are not indicated except for electrolytics and • a : Through hole.
tantalums. • : Pattern from the side which enables seeing.
• All resistors are in Ω and 1/4 W or less unless otherwise (The other layers' patterns are not indicated.)
specified. TUNER UNIT
• f : internal component. Caution:
• C : panel designation. Parts face side: Parts on the parts face side seen from
(SIDE A) the parts face are indicated. I/O board
Note: The components identified by mark 0 or dotted Pattern face side: Parts on the pattern face side seen from DMB12 board
line with mark 0 are critical for safety. (SIDE B) the pattern face are indicated.
Replace only with part number specified.
FL board SPEAKER board
✩ New part of EEP ROM (IC103, IC706) on the DMB12 board • Indication of transistor.
cannot be used. Therefore, if the mounted DMB12 board C
(A-1148-813-A) is replaced, exchange new EEP ROM
(IC103, IC706) with that used before the replacement. Q These are omitted. MAIN board
• A : B+ Line. B E
• Voltages and waveforms are dc with respect to ground un-
der no-signal (detuned) conditions.
• Voltages and waveforms are dc with respect to ground in
service mode.
• Waveforms are taken with a oscilloscope. BC E
Voltage variations may be noted due to normal production These are omitted
tolerances. HEATSINK (A) board
no mark : DVD STOP SW board
* : Impossible to measure HEATSINK (B) board

• Voltages are taken with VOM (Input impedance 10 MΩ).
• Circled numbers refer to waveforms. LED board
• Signal path.
POWER board
F : AUDIO
J : CD PLAY JACK board
c : DVD PLAY
I : SACD PLAY
d : TUNER
L : VIDEO
E :Y
a : CHROMA
r : COMPONENT VIDEO
f : AUDIO IN
HCD-DX375
33 33

HCD-DX375
6-1. BLOCK DIAGRAM – RF SECTION –
CN105
6 RFMON
RF
6 DVDRFIP V2REFO 28 5 V2REFO
TO DIAG JIG • Signal Path
OSP 252 253 OSN RXD 106 2 RXD
TXD 107 1 TXD
: CD PLAY
A
2 DVDA : DVD PLAY
B
DETECTOR 3 DVDB
C : SACD PLAY
4 DVDC
D
5 DVDD
D
C
B
A
F
19 TPI
E
18 TNI
A
8 NA D VIDEO SECTION
(Page 37) IC621
B IC701
9 NB CHANGER CONTROL
OPTICAL PICK-UP D IC101 (1/3) LD/ST MOTOR DRIVE
10 MD IC501 (1/4)
BLOCK C CD/DVD RF AMP, M
11 MC SYSTEM LD/ST MTR NEG 7 FIN OUT1 4 M761
(KHM-310CAB) FOCUS/TRACKING ERROR AMP P0 24
CONTROLLER LD/ST MTR POS LD/ST MOTOR
DVD SYSTEM PROCESSOR P1 23 9 RIN OUT2 2
DIGITAL SERVO PROCESSOR
VC 29 V2O
IC711
LIMIT 176 LI M SW BU U/D MOTOR DRIVE
IO_CE 85 4 LATCH BU U/D MTR POS
7 FIN OUT1 4
M
LASER Q102 (1/2) P4 20 M762
CD LD IO_CLK 89 3 CLK BU U/D MTR NEG BU U/D MOTOR
DIODE AUTOMATIC POWER 23 LD01 P5 19 9 RIN OUT2 2
(FOR CD) CONTROL (FOR CD)
IO_RESET 86 2 RESET B
IO_DI 87 26 BI1 SW3 S761( SUB TRAY OUT ) IC751
38 MTK_RST P9 11 S731
PD 20 MD12 SW2 D SENSOR
13 LATCH 0 P10 10 SUB TRAY IN
21 MD11 IN D+3.3V
14 CLK 0 P11 9 S721
LASER DVD LD Q102 (2/2) MAIN TRAY
22 LD02 SCO OPEN IN/OUT
DIODE AUTOMATIC POWER IFSCK 99 33 DVD_SCO 15 BO1
(FOR DVD) CONTROL (FOR DVD) 25 BO2 P14 6 Q751
SCD BUFFER
IFSDO 98 32 DVD_SOD
VR650 SID
Q101, Q103 IFSDI 101 31 DVD_SID
48 MSW
VR780 VOLUME CONTROL XIFCS 100 37 DVD_XIFCS S781
IC622 ROTARY ENCODER
CHANGER CONTROL ST U/D ENCODER
MSW
IC201
FOCUS/TRACKING COIL DRIVER,
16 BI2 P15 5
XIF5SY 114 34 DVD_XIFBUSY 26 BI1 P14 6
SPINDLE, SLED MOTOR DRIVER
IOP
3 CLK P13 7
15 39 TROPENPWN 4 LATCH P12 8
42
BUFFER 9
41 VREFO S771
12
ROTARY ENCODER
43 ( MD )
FCS+ FMO
36 FOCUS COIL 48 38 FMO
2AXIS FCS– FOO FOO P11 9
37 DRIVE 1 42 FOO 2 RESETB
DEVICE P10 10
FOCUS/ IO_DO 88 25 BO2 P9 11
TRK+ DMO
TRACKING 35 TRACKING COIL 3 37 DND CDM_OPEN_SW 27 P8 12
TRK– TRO TRO
COIL 34 DRIVE 4 41 TRO
FMO
REG02 10 30 V REFO
+3.6V DMO
13
REG01 CNVss 9
+2.5V 32 SLED MOTOR
31 DRIVE
SL– CN503
30 40
(SLED MOTOR) M SL+
29 SLED MOTOR
40 IOPMON
3 CNVss
DRIVE 45 47 SPFG 7 RTSI
POWER SECTION
19 211 MUTE123 (Page 38) E 2 RESET
TO WRITE JIG
SP+
27 SPINDLE MOTOR 20 210 MUTE 5 CLKI
(SPINDLE MOTOR) M SP–
28 DRIVE 22 170 TSDM 4 RXDI
21 8 TXDI
47
BUFFER
46
HCD-DX375
34 34

HCD-DX375
6-2. BLOCK DIAGRAM – AMP SECTION –
IC352 IC101 (3/3)

AUDIO INPUT SELECTOR DVD SYSTEM PROCESSOR
IC353 220 SPDATA

11 X3
AMP
IC401 15 X2 IC4601
AMP A/D CONVERTER
L-CH
14 X1 LIN
6 – 7
X 13 3 + 1 1 LIN DOUT 12
J401 L –
5 + 12 X0
2
LRCK 10
AMP LRCKO AUDIO
AUDIO IN AMP BCKO SECTION
R 5 + RIN BCK 11 (Page 36)
3 + Y 3
7 2 RIN AMP MCKO
2 –
1 4 Y3
6 – SCKI 15 A VIDEO
Q470-473,476 IC402 SECTION
AMP 2 Y2
MO/ST DETECT (Page 37)
R-CH
5 Y1
5 + 7
ACAL
6 –
1 Y0
D470 A B
Q360-362
MUTING 10 9
Q353 Q354
Q474,475 GAIN CONT

GAIN CONT
DC CONT
MO/ST DET
A SEL1
A SEL0
D433 PLUG DET1
L
J200
VCR R
TV R IC501 (2/4)
SYSTEM CONTROL
82 A-SEL0
83 A-SEL1
ACAL ACAL MIC LEVEL
91
GAIN CONT MIC GAIN
26
DC CONT DC CONT
28
MO/ST DET MONO/ST DET
90
L-CH PLUG DET1 MIC/A CALSW
100
R-CH CN502
TUNED TUNED TUNED I2C CLK
TUNER 69 29 3 I2C CLK
PLL CK PLL CK I2C DATA SOFT JIG
SECTION 70 ST_CLK 30 4 I2C DATA
PLL DO PLL DO
71 ST_DO
PLL CE PLL CE
72 ST_CE
PLL DI PLL DI
73 ST_DI
• Signal Path
: AUDIO IN
V_SEL0
80 V_SEL0 : TUNER
V_SEL1
81 V_SEL1
VIDEO
SECTION B
(Page 37)
HCD-DX375
35 35

HCD-DX375
6-3. BLOCK DIAGRAM – AUDIO SECTION – IC3001
COMPARATOR
3 + 1
L J402
2 – R PHONES
5 + 7
6 –
PLUG DET2
HPMUTE Q450,451
Q3081 Q460,461
IC3500 MUTE SW MUTE
S-MASTER DIGITAL AMP
• Signal Path 28
14 PWMB OUTB 30 LPF
: AUDIO 6 PWMA OUTA 25 LPF

27
5 RESET
4 SD
IC3030
S-MASTER PROCESSOR
VIDEO IC3400 SPEAKER

SECTION AMP_D1-D3 AMP_D3 WF
C 31 DATA OUTL1 11 S-MASTER DIGITAL AMP
(Page 37) WF
MCK0 25
36 XFSIIN OUTL2 9 LPF (+)
AMP BCK0 14 PWMB OUTB 27
AMP MCKO IC4502 30 BCK C
SECTION A 2 A
AMP
Y 4 LRCK0 OUTR1 6
6 PWMA OUTA 28 (–)
WOOFER
(Page 35) 29 LRCK C LPF
4 30
VIDEO 25 FLAGL OVF OUTR2 5 RESET
AMP BCKO,AMP LRCKO OVF2
SECTION 24 OVF FLAGR
SD
(Page 37) SCDT
21 SCDT Q3401,3402
SHIFT 4
22 SCSHIFT DC
LAT3
23 SCLATCH DETECT
INIT IC3300
27 INIT
NSPMUTE FS0I 38 S-MASTER DIGITAL AMP
IC501 (3/4) 18 NSPMUTE
IC802 SOFTMUTE
SYSTEM CONTROLLER 19 SOFTMUTE 28
FL DRIVER XFS0IN 48 6 PWMA OUTA 30 LPF (+)
20 PGMUTE CENTER
14 PWMB OUTB 25 LPF (–)
SG1 – SG16
DIN 7 24 FL DATA 27
14 – 29
5 RESET
CLK 8 21 FL CLK
SD
STB 9 25 FL CS/STB IC3010
S-MASTER PROCESSOR 4 Q3301,3302
AMP_D0-D3 DC
DIPCSFLAG 19 HP
HPOUTL2 43 DETECT
GR2 – GR12
D3071-D3073 TB301
41 – 31
FL801 30 HP
VFL HPOUTL1 45
FLUORESCENT 20 PGMUTE HP
INDICATOR TUBE HPOUTR2 39
GR1
IC3100
HP S-MASTER DIGITAL AMP
42 AMP_D1 HPOUTR1 41
+3.3V 31 DATA FR 25
F1 OUTR1 6 14 PWMB LPF (+)
OUTB 27 FRONT
F2 MCK0 FR
36 XFSIIN OUTR2 4 6 PWMA OUTA 28 LPF (–) R
Q802 BCK0
G1 30 BCK FL 30
FL DRIVER OUTL1 11 5 RESET
LRCK0
29 LRCK FL
SD
KEY0 – KEY2
25 FLAGL OVF OUTL2 9

97,95,94
S801 – S813 OVF 4 Q3101,3102

24 OVF FLAGR DC
(FUNCTION KEY) SCDT
21 SCDT DETECT
SHIFT FSOCKOUT 37
X501 22 SCSHIFT
Xout 13 LAT1
5MHz 23 SCLATCH 38
KEY0
FS0I
INIT IC3150
27 INIT IC3051
NSPMUTE XFS0IN 48 S-MASTER DIGITAL AMP
74 KEY INT Xin 15 18 NSPMUTE OSC
SOFTMUTE 28
19 SOFTMUTE
14 6 PWMA OUTB 30 LPF (+)
XFS0OUT FRONT
IC803 14 PWMB OUTA 25 LPF (–) L
D813-D815 IC3003 X4501
( INDICATOR ) LED DRIVER 27
SELECTER 49.152MHz 5 RESET
6 Q0 DATA 3
SD
Q811-Q820 | CLK 4 2
-
LED SWITCH 15 Q9 Q3151,3152

LCK 5 22 LED LAT 5 4
1 DC
IC3020 DETECT
6
S-MASTER PROCESSOR
E3.3V
MST 68 IC3200
IC801 20 PGMUTE S-MASTER DIGITAL AMP
REMOTE CONTROL 4 SIRCS–IN AMP_D2
RECEIVER SR 25
31 DATA OUTR1 6 14 PWMB OUTA 27 LPF (+)
HPMUTE MCK0 SR SUR R
HP_MUTE 53 36 XFSIIN OUTR2 4 6 PWMA OUTB 28 LPF (–)
PLUG_DET2 BCK0 30
HP_SW 52 30 BCK SL 5 RESET
SCDT LRCK0 OUTL1 11
DAMP SCDT 1 29 LRCK
SD
SHIFT SL
DAMP SHIFT 2 25 FLAGL OVF OUTL2 9
LAT1 SCDT 4 Q3201,3202
S800 10 ENA DAMP LAT1 47 21 SCDT DC
LAT2 SHIFT
VOLUME DAMP LAT2 48 22 SCSHIFT DETECT TB302
ENCODER 11 ENB LAT3 LAT2
DAMP LAT3 49 23 SCLATCH FS0I 38
INIT INIT
DAMP INIT 50 27 INIT
SOFTMUTE NSPMUTE IC3250
VOLUME DAMP SOFT MUTE 51 18 NSPMUTE
OVF SOFTMUTE S-MASTER DIGITAL AMP
OVERFLOW1 44 19 SOFTMUTE XFS0IN 48
OVF2 28
OVERFLOW2 45 24 OVF FLAGR
XFS0OUT 14 6 PWMBP OUTA 30 LPF (+)
SUR L
14 PWMAP OUTB 25 LPF (–)
27
5 RESET
Q3251,3252
SD
DC
RESET 4 DETECT
DRIVE RST 42
FAN
DIAG Q3551 FAN
DRIVE OCP 43 +12V DRIVE
PROTECT DETECT
Q3000-3002
HCD-DX375
36 36

HCD-DX375
6-4. BLOCK DIAGRAM – VIDEO SECTION –
AMP LRCKO,AMP MCKO,AMPBCKO AMP SECTION AUDIO SECTION

A (Page 36)
(Page 35)
AMPDO,AMPD2,AMPD3 AUDIO SECTION
C (Page 36)
SPDIF 225 72 SPDIF TX2P 58 1 TMDS DATA2 +

ALRCK 213 79 ALRCK TX2N 57 3 TMDS DATA2 -
ABCK 214 78 ABCK TX1P 55 4 TMDS DATA1 +
ACLK 215 77 ACK TX1N 54 6 TMDS DATA1 -
ASDATA0 217 76 AD0 TX0P 52 7 TMDS DATA0 +
ASDATA1 218 75 AD1 TX0N 51 9 TMDS DATA0 -
ASDATA2 219 74 AD2 TCKP 49 10 TMDS CLOCK +
IC701 CN701
ASDATA4 222 73 AD3 HDMI DRIVER TCKN 48 12 TMDS CLOCK -
YUV0 +3.3V HDMI OUT
SMPTE_Y0 177 13 Y0
YUV1 | | IC705
SMPTE_Y1 176 HTPLG 40 AND GATE
YUV2 20 Y7 2
SMPTE_Y2 174 IC111 TX27M 4
1Y 6 26 CLK MSD 35 1
OSC
SMPTE_Y3 172 2Y 1A 2A
YUV3-7 11 VCK MSCK 34
| 4 1 3
SMPTE_Y7 168 39 HSYNC
X101 19 HPD
VCLK 178 27MHz 38 VSYNC
TRAP2
PWDN
SSCK
SSD
15 SCL
CLK
Q701,702
INT
229 BUFFER 16 SDA
21 22 24 25 27 31
207
205 IC706
EEP ROM
IC150 63 62 60 59 24 61
RESET
XTXRST
SCK
SDA
XPWDN
22 VSYNC
XTXINT
TRAP2
105 1 A SCK 49 6 SCL
Y 4 21 XRST
110 2 B SDT 50 5 SDA
XRST
SIN 51 7 WP
XSMCS
211 23 XSMCS IC708
SMSCK HDMI PROCESSOR
208 32 SCK
31 SDO SCLO 40
SDAO 41 CN101
TXD 30 SDI
MOD 13 1 XEXRST
X0
XI
14 15 2 DLON
SMSDI TO CHECK
209 X701 5 RXD
S1701
SMSDO NOM-DL 10MHz 6 TXD
210
RXD IC201
VIDEO AMP, 75Ω DRIVE
J201
COUT 26 1
YUV2 196 2 CIN S VIDEO
MONITOR
(DVD ONLY)
YUV1 194 6 YIN YOUT 21 2 OUT
YUV3 198 4 CVBSIN VIDEO

CVBSOUT 23
CY
YUV4 200 10 CYIN
CB
YUV5 202 12 CBIN
CR CYOUT 20 Y J202
YUV6 203 14 CRIN
COMPONENT
WIDE CbOUT 18 PB/CB
WIDE 179 25 S1 VIDEO OUT
CrOUT 16 PR/CR
D RF SECTION 13 1
(Page 34)
V SEL0 AMP
B SECTION
V SEL1 (Page 35)
IC101(2/3)
DVD SYSTEM PROCESSOR
HIGHA0-7
XROMCS
DRCLK
IOA0-7, IOA18-IOA21
DQM0
DQM1
EEWP
RWE
XWR
RA0 – RA11
SDA
RCS
RAS
XRD
CAS
SCL
BA0
BA1
CKE
A16, A17 RD0 – RD15

HD0 – HD7
53-61, 67-72, 74-76, 125-123, 121, 120, 118, 146, 147, 149-151,
51 102 103 81-84,86-88,91 77 79 66 143 145 156 142138140139 113 137 157
78, 89, 92, 93 117, 115, 135, 133-128, 126 158-160, 162, 164-166
HD0 – HD7 A0 – A21

7 6 5
DATA & ADDRESS BUS
SCL
SDA
WF
22-26,
2,4,5,7,8,10,11,13,42,44,45,47,48,50,51,53 20 21 38 19 16 18 17 15 39 37
29-35
BA0
BA1
CLK
CS
WE
RAS
CAS
LDQM
UDQM
CLKE
RD0 – RD15
RA0 – RA11
IC103 DATA & ADDRESS BUS

IC104 • Signal Path
64M SDRAM
EEPROM
: VIDEO
A1-A21
XROMCS
A0
HD0 – HD7 :Y
XRD
XWR
: COMPONENT VIDEO
29,31,33,35,38,40,42,44 45 25-16, 10-1, 48 26 28 11
: CHROMA
CE
OE
WE
DQ0 – DQ7 DQ15/A-1 A0,A2 – A21
IC102 : AUDIO
32M FLASH ROM
HCD-DX375
37 37

HCD-DX375
6-5. BLOCK DIAGRAM – POWER SECTION –
POWER
Thermistor F901
T901 D901
TRANSFORMER(MAIN)
AC IN
LINE
FILTER
D931
+31.5V D905 Q901 IC901
T801 POWER
VOLTAGE
DC/DC PROTECTION
IC931 CONTROLLER
CONVERTER
VOLTAGE
F1 DETECT
PC901
TO FLUORESCENT F2 +5V
PHOTO
INDICATOR TUBE D801,802 COUPLER
VFL D804,805
RECT Q943,947 E4V
Q801 PC903
OSC VOLTAGE PHOTO
DETECT COUPLER D910
T902
A12V TRANSFORMER (SUB)
D941
IC360 IC941
+9V
+9V REG +12V REG IC921
D922 Q921 POWER
PROTECTION
REG
SW+9V
Q945 D944
IC707
+5V MOTOR DRIVE
+5V REG
IC504 CONTROLLER
A+5V
+5VREG
IC502
+3.3V
+3.3V REG
IC105 +6V
+3.3V
+3.3V REG
SW +5V
IC501 (4/4) D942
+3.3V IC703 Q504 IC942
SYSTEM CONTROLLER
+3.3V REG 5V SW D+5V REG
E 4V
IC107
RF+3.3V
+3.3V REG
P CONT2 40 E3.3V
D502 D943
IC110 IC943
BMP3.3V +1.8V
+1.8V REG +3.3V REG
D504
P CONT1 39
P CONT3 41
IC951
IC3050 VOLTAGE
+1.8V
+1.8V REG DETECT
PC902
AC_CUT 20 IC702
+1.8V PHOTO
+1.8V REG
Q503 COUPLER
IC503
RESET 12
RESET
SW+3.3V,+3.3V
D3.3V
E RF SECTION
(Page 34)
HCD-DX375
38 38

HCD-DX375
6-6. PRINTED WIRING BOARD – DMB12 BOARD (SIDE A) – • See page 33 for Circuit Boards Location. :Uses unleaded solder.
✩ New part of EEP ROM (IC103, IC706) on the DMB12 board

cannot be used.
Therefore, if the mounted MAIN board (A-1148-813-A) is
for CHECK replaced, exchange new EEP ROM (IC103, IC706) with that used
before the replacement.
NOM
• Semiconductor
Location
Ref. No. Location
DL IC101 D-6
1 6
IC104 IC102 D-8
IC103 C-8
IC104 B-7
IC110 F-6
IC201 F-8
HDMI OUT
(DVD ONLY) IC701 IC701
IC708
C-3
C-4
Q101 G-6
IC708 Q103 G-6
IC103
IC101
IC102
O
2 8
MAIN BOARD
CN701
(Page 49)
9
P
MAIN BOARD
CN504
(Page 48)
IC110
1
3
IC201
S1 D1
S2
D2
12
B N OPTICAL PICK-UP SPINDLE MOTOR
C I/O BOARD MAIN BOARD

BLOCK
(KHM-310CAB)
for DIAG JIG SLED MOTOR
I/O BOARD CN201 CN505

CN202 (Page 56) (Page 49)
(Page 56)
HCD-DX375
39 39

HCD-DX375
6-7. PRINTED WIRING BOARD – DMB12 BOARD (SIDE B) – • See page 33 for Circuit Boards Location. :Uses unleaded solder.
• Semiconductor
Location
Ref. No. Location
R754 IC105 D-2
1 5
IC150 R756 3 4 IC7054 3

IC107
IC111
E-5
D-5
IC707
5 1 IC150 B-4
IC702 D-7
IC703 C-8
IC705 B-8
E
IC706 C-7
IC707 B-7
E IC4502 E-6
IC4601 F-8
Q102 G-5
IC706 Q701
Q702
B-6
B-6
IC703
4 3
5 1
IC111 3 1
IC702
6 4 5
1
IC105
1 5
3 4
5 4
1 5 4
3
IC107 IC4502
1 3
IC4601
E1 C1
B2 B1
C2 E2
12
HCD-DX375
40 40

HCD-DX375
6-8. SCHEMATIC DIAGRAM – DMB12 BOARD (1/7) – • See page 66 for IC Block Diagram.
45
46 43
42
45
46
CN4301
R4701 11P
0 JL4703
CN601 FL601 FB604 JL4704
5P FB602
0UH 0UH 0UH
JL611 JL612 JL4705
JL613 JL614 FL603 C602 R4702 JL4706
FB603 0UH FB606 47 0
JL609 JL610 0UH 0UH 10V JL4707
JL601 JL602 C603 R4703 JL4708

47 0
JL603 JL604 10V JL4709
FL602 R4704 JL4710

FB601 FB605
6/6 0UH 0UH 0UH 0 JL4711
CN505
55 JL4712
R4705 57
0 JL4713
R4706
0
C4610
0.1 16V B
IC4601
PCM1803DBR
C4609 R4611
10 16V CN4302
C4601 C4602 100 5P
10 0.1 1/10W
L3601 10V 16V C4611 JL4301
F B 0.01 25V B JL4302
C4608
42 45 10 16V
C4621
0.01 25V B JL4303
44 46 C4607
47 R4609 0.1 16V B R4621 100 1/10W JL4304
0
L4602 JL4305
C4606 C4605
R4601 0.1 47
100 16V 10V 57
1/10W B
C4603
R4607 0 0.1 R4619
16V 0.001U 25V B
B
43
R4603
10k 1/10W
R4602
100
1/10W
R4801
0
R4805 0
R4802 R4605 0
0
R4501 0
R4803 R4606 0
0
R4502 0
43 FL4501 C4501 C4502

0UH 10 0.01 CN4501
10V 25V 9P
46 F B
R4505 R4514 JL4501
0 0UH JL4502
R4504 0 JL4503
R4503 0 R4515 0UH JL4504
R4506 0 R4516 0UH JL4505

R4507 0 R4510 0UH JL4506
JL4507
R4511
0UH JL4508
C4504
0.01 25V B 1/6
R4512 JL4509
0UH
R4520 50
0
IC4502
SN74LVC1G125DCKR
HCD-DX375
41 41

HCD-DX375
Ver. 1.1 ✩ New part of EEP ROM (IC103, IC706) on the DMB12 board cannot be used.
6-9. SCHEMATIC DIAGRAM – DMB12 BOARD (2/7) – Therefore, if the mounted MAIN board (A-1148-813-A) is replaced, exchange
new EEP ROM (IC103, IC706) with that used before the replacement.
41 45 47
44 46
45
41 C193
45 0.22
46
TK11133CSC
IC107
L-G
C195
0.22
R102
45 0
C101 C192
0.01 0.01
CN101
24P JL139
JL140
JL141
JL142 C114
Q101 0.1
JL143 UM6K1N-TN C117
10 16V
JL144 C115
0.1
C118
10 16V
JL145 CL112 C116
R117 0.1
JL146 47k C119
1/10W 10 16V
JL147 CL113 C199
JL148 0.0047
JL149 CL114 R116 43

1k
JL150 CL115
JL151 CL116 R108 R111
JL152 1M 100
JL153
JL154 CL117
JL155 CL118
JL156
JL157
JL158 Q103
RT1N241C-T112-1
JL159 R101
100
22 1/10W 0.5%
22 1/10W 0.5%
22 1/10W 0.5%
R112
R113
R115
R120
R121
R118
45 IC102
22
22
22
S29AL032D70TF-
C105 CHI1-0611UC 43
47
10V R124
CL106 47k
R110
CL107 47k
1/10W
C112 FB111
R107 47 R193 0UH
1k
45 10k 10V
R109 R123 C184 R191

0 0 0.01 1k
Q102
QST8TR
R114 R1129 C106 C113

100k 100k 0.01 0.01
BR24L64F-W
IC103
45
E2
R105 C102
10k 1 6.3V B
R106
TK11133CSC
10k
IC105
L-G
44
R1133
C186 0
0.22 16V B
C182 R151
0.22 10k
HCD-DX375
42 42

HCD-DX375
6-10. SCHEMATIC DIAGRAM – DMB12 BOARD (3/7) – • See page 65 for Waveforms. • See page 73 for IC Pin Function Description.
41 46 47
46 41
44
R1120 0UH
0.01
R1121 0UH
C157
R1122 0UH
R1186
0UH
R1169
R159 47
R161 47
R160 47
R163 0UH
R165 0UH
R167 0UH
46 0 47 R1123 0UH
R1124 0UH 41
FB123
FB112
JL105
JL106
0UH R189 R190 R192 R195 R197 R1102
C145 R146 C161 C163 150 150 150 150 150 150 R1125
C135
0.033
C143
C140
C141
C139
C137
R1191
22p
R136 1 47 0UH
0.1
0.1
0.1
0.1
C130 15k 0 0.01 0.01 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W
0.1 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% IC111
TC7PAU04FU (TE85R)
C132
MM1661JTRE
0.1
47 1/10W
10 16V
FB107
0.001
IC110
C156
0.1
0.01
680k
0UH
0.1
C138 C147 C148
0
C133
C149
47
47
47
0.001 0.047 0.047
C151
0
0.1
0
R162
R164
R141
R166
R169
R143
C154
C142
C150
JL103
JL104
47
R184
R183
R185
0.1
R125
R172
R173
C187
47
CL119
4V R1134 R132
0 100k R142
100k
R1178
1k X101
C198 R1167 27MHz R1168
1 0 220
C183
0.33
R1101
2.2k
1/10W C152 C153
C120 1 0.5% 15p 15p
C121 1 OSC
R174
0
C122 1
C1103 C1107
C123 1 C171 0.001 0.001
0.001
R175 0.01
0.001
0.001
0 R1179
JL101 100
C124
C1104
1
C1105
C1106
R171 100
R1185 100
R1184 100
R140 R133
10k 1/10W 0
45
R170 R138
10k 100
R1183 220
C172 RB116
0.01 47
1/32W
46
C125 CL101
0.1 RB117
47
RB114 1/32W
0
IC101
CXD9804R
C126 RB115
0.1 0
CL103
42 CL104
CL105
R1114
C174 22
0.01 1/10W
CL108
C175 RB104
0.01 0
R130 R135
0.01 10k
RB103
0
JL136
R1177
100
C127 C176
0.01
0.01
RB111
0
C173 R139
0.001 0
44
RB109
0
R103
0
0.0015
C128
RB110
0
CL1102
CL120
CL123
CL1101
JL160
JL161
FB115
0UH
FB106
0UH
C164 0.01
C144 C162
0
0UH
C131 C136 R1176 C155 C158

0
0
0.01 0.01 C177

100
3.3k
2.2 0.01 0 0.01 0.01

0
R154
RB112 RB113 47
0
0
R145
R1115
R155 C160 0 0 10V

R152
R153
R1400
R148
R147
R156
0 0.01
R1201
44
42
45
HCD-DX375
43 43

HCD-DX375
6-11. SCHEMATIC DIAGRAM – DMB12 BOARD (4/7) – • See page 67 for IC Block Diagram.
43
IC104 EDS6416AHT A-75-E C197

0.1
16V
B
C181
RB108 0.1
0 16V
B
43 C180
0.1
16V
B
RB106
C191 47
RB107 0.1 1/32W
0 16V
B
C179
0.1
16V
B
RB105
C190 47
47 1/32W
10V
FB108
0UH
R1150
3.3k 1/10W
R1151
3.3k 1/10W
R1152
3.3k 1/10W
41
42
45
46
42 47
6P
JL107
JL108
JL109
for DIAG JIG JL110

JL111 R1110 2.7k
JL112
C1501
0.01
R1503
0
R1502
IC150 0
SN74LVC1G0
47 8DCKR
R1501
0
CN109
11P R1173
JL1113 0
JL1114 R1143 0
JL1115 R1145 0
JL1116 R1138 0
JL1117 R1139 0
JL1118 R1140 0
JL1119 R1141 0
JL1120 R1170 0
JL1121 R1142 0
6/6
JL1122
43
55
JL1123
HCD-DX375
44 44

HCD-DX375
6-12. SCHEMATIC DIAGRAM – DMB12 BOARD (5/7) –
42
41
42 R230 R231 R232
46 R223 R225 82k
15k 18k
100k 100k 1/10W 1/10W R234 1/10W
1/10W 1/10W 0.5% 0.5% 10k 0.5%
0.5% 0.5%
1/10W 0.5%
C209
0.033 C211
CL208
CL207
0.033 C212 CL206

1/10W 0.5%
C215
R233
R221 0.01
C233 56k 25V 0.01
0.0047 R220 1/10W B
R226
1k 0.5%
33k
56k
C214
0.001 CL209
R212 50V
10k B
R214 15k CL210

42
R208 C205 CL211

33k 220p CN201
CL201 6P
CL212 JL201
R206 10k R209 33k JL202
R215 JL203
C206 12k
220p JL204
CL202 JL205
C203 JL206
0.01 C224
25V C219 0.01
B 0.01
R207 C218
C220 R246
2.7k 10
16V 10 4.7k R247
16V 1k 43
R204 C221
1.2k CL203 0.1
42
R205 R216 C222
10k 12k 0.1
R210 208
47k 0.01
IC201
CL204
FAN8036L
R213
6.8k
42
41 44
42 46
CL205
C213
0.01
R219 R224 C217 47 16V 41

27k 10k R2504
4.7k 46
1/10W
C210
0.01
42
43
HCD-DX375
45 45

HCD-DX375
✩ New part of EEP ROM (IC103, IC706) on the DMB12 board cannot be used.
6-13. SCHEMATIC DIAGRAM – DMB12 BOARD (6/7) – • See page 66, 67 for IC Block Diagrams. Therefore, if the mounted MAIN board (A-1148-813-A, etc.) is replaced,
exchange new EEP ROM (IC103, IC706) with that used before the replacement.
41
C717 R734 C718 42
0.01 0 0.01
44
45
47
R740
0
TK11133CSC
TK11118CSC
IC703
IC702
L-G
L-G
R731 R736
0 0
41
C736 C716 C719 C720 C723 42
47 0.22 0.22
4V 0.22 0.22 45
R1705 R1706
1k 1k
C707 FL701
22 0UH
10V
0
0
0
0
0
R702
R704
R703
R714
R793
C709 R728
0.1 0
43 C702
0.1 R738
16V 0
B
C710 FL703
10
41 16V
0UH
43 R730
510
CL701
CL702
CL703
LF701
CL704 C711 0.1 0UH
CL705
CL706
LF702
CL707 0UH
C701 CL708
0.1
IC701
R701 0 CXD9873Q LF703
C712 0.1 0UH
LF704
C714 0UH
0.1 C715
16V 47
B 10V R747 JL701
FL704 0
C713
43 0.0056 25V B
0UH
R748
0 R751
CL710 0
R749
1.8k
R752
SN74LVC1G0
C725 0 CN701
8DCKR
IC705
0.01 19P
R750
1.8k
10k
R705
10k
10k
4.7k
R744 R742
R1750
R718
47k
R722
R723
4.7k
4.7k
C704
0.01
0.1
C703
R787 R743 R745

4.7k 1k 1k
C727
R712
0.01
100
25V
0
R725
B
R724
0
R788
R708
R709
1k
1k
10k
R1751
TK11150CSC
43
R755
IC707
L-G
IC706 C726
BR24L16F-WE2 0.1
41
R753 45
0
C729 C730
0.22 0.22
47
HCD-DX375
46 46

HCD-DX375
6-14. SCHEMATIC DIAGRAM – DMB12 BOARD (7/7) – • See page 65 for Waveform.
46
R763 R762
0 0
R772
CL751
CL750
0
R783 R784
0 0
C732
0.01
CL742 Q702
2SK1399-T1B
CL743 Q701
2SK1399-T1B
CL744
CL745
CL755
R781
10k R785
0
R786
0
R782
10k
R766
4.7k
IC708
R767 MB95F108ASPFV-
0 GE1-H0601
CN1701
R1701 6P
0 JL1701
X701 R792 JL1702

10MHz 4.7k JL1703
JL1704
R765 R1702 0 JL1705
0
JL1706
R1703
0
CL735
C734
0.01
C731
FL705 22
R790
0UH 10V
4.7k
41
42
44 C733 R764
0.01 4.7k R1710
45 4.7k
46
R760
R759
R789
100
R773
0
0
100
R769
0
44
R1715
0
R780 0
S1701
43 R770
0
R771
0
HCD-DX375
47 47

HCD-DX375
6-15. PRINTED WIRING BOARD – MAIN BOARD (SIDE A) – • See page 33 for Circuit Boards Location. :Uses unleaded solder.
DMB12 BOARD
for WRITER JIG P CN109
(Page 39)
• Semiconductor
Location
IC3050 10 Ref. No. Location
11
IC501 D-10
IC502 C-13
IC503 D-9
E IC3001 IC621 C-12
IC3100 IC622 E-12
E IC3001 C-7
IC502 FL BOARD
IC3003 E-8
IC3051
A CN801
(Page 58) IC3010 D-6
IC3020 E-6
IC621 IC3030 G-6
E IC3050 B-6
IC3150 IC3051 C-6
IC503 IC3100 B-5
E
IC3150 C-5
IC3200 D-5
E IC3250 E-5
IC3010 IC501 IC3300 G-5
RELAY BOARD IC3400 H-5
E IC3200
IC3003
D CN701
(Page 61)
IC3500 I-5
E
Q503 C-9
IC622 Q3101 B-1
Q3102 C-1
IC3020 Q3151 D-1
Q3152 D-1
IC3250 I/O BOARD Q3201 D-1
E E CN311
(Page 56)
Q3202 E-1
Q3251 F-1
E
Q3252 F-1
14
15
Q3301 G-1
Q3302 G-1
Q3401 I-1
Q3402 I-1
Q3551 J-3
IC3300
E
E IC3030
IC3400
E IC3500
JC502
E 14
14
HCD-DX375
48 48

HCD-DX375
6-16. PRINTED WIRING BOARD – MAIN BOARD (SIDE B) – • See page 33 for Circuit Boards Location. :Uses unleaded solder.
POWER BOARD POWER BOARD JACK BOARD

CN904
(Page 63) F SOFT JIG
CN902
(Page 63)
G H CN403
(Page 58)
(CHASSIS) (CHASSIS)
(CHASSIS)
(CHASSIS)
12 1 1
N 3 1
DMB12 BOARD
CN601
5 1
IC504
(Page 39)
SPEAKER BOARD
I CN301
(Page 60)
R544
R543
SPEAKER BOARD
J CN303
(Page 60)
(CHASSIS)
SPEAKER BOARD
M CN303
(Page 60)
8
9
O
DMB12 BOARD SPEAKER BOARD
CN4501
(Page 39)
K CN302
(Page 60)
E E
14
E
14
(CHASSIS) (CHASSIS)
• Semiconductor Location (CHASSIS)
(CHASSIS)
Ref. No. Location Ref. No. Location Ref. No. Location Ref. No. Location FAN
D501 C-6 D3151 C-12 D3401 H-12 Q504 B-5
D502 C-7 D3152 D-12 D3402 H-12 Q3000 J-12
D504 C-7 D3201 D-12 D3501 I-12 Q3001 J-12
D3071 E-7 D3202 E-12 D3502 I-12 Q3002 J-12
D3072 E-7 D3251 E-12 D3551 J-13 Q3081 D-8
D3073 E-7 D3252 F-12 D3552 J-13
D3111 B-12 D3301 G-12
D3112 C-12 D3302 G-12 IC504 B-5
HCD-DX375
49 49

HCD-DX375
Ver. 1.1
6-17. SCHEMATIC DIAGRAM – MAIN BOARD (1/6) – • See page 68 for IC Block Diagrams.
R3060 10k
R3059 10k
EB3001
TERMINAL BOARD
C3035 C3034
0.1 0.1
R3062 100
R3063 1k TP3031
R3031
470
R3064 1k
TP3003 R3065 1k
TP3004 ICT3063 R3066 100
R3067 100 R3032

470
R3068 100
R3069 100 TP3032
R3033
R3070 100 10k C3033
0.1
R3071 100
R3072 100 R3034 100
R3073 100 R3035 100

R3301
C3071 100
55 0.1 IC3030 C3032
C3036 CXD9843AR
0.1 0.1
C3067 100p
C3068 100p
C3069 100p
R3097 C3037 R3302

C3070 0.001
100 0.1 100
R3037 TP3033
1.5k
C3031
47
16V
IC3003
TC7WH157FK (TE85R)
54 51
C3073
0.1
C3038 C3039 C3040

R3077 100
0.1 0.1 0.1
R3057
100
EB703
R3078 100
TERMINAL BOARD
R3079 100
GROUND
C3072
0.1
R4002 0
C3025 C3024
CN701 C3075 0.0047 0.1 0.1
9P
TP3002 R3075 100
TP708
TP707 R691 0 ICT517
TP706 R692 0 ICT518 R3076 100
TP705 R693 0 ICT519 R3021

R702 0 ICT522 470
TP704 R694 0 ICT520
TP703 R695 0
R701 R3080
220 R696 0 ICT521 100k
TP702 R3022
ICT3062 470
1SS355WTE-17
1SS355WTE-17
1SS355WTE-17
TP3021 R3251
TP3022 100
D3072
D3073
41
D3071
C3023
0.1
25V
R3023 100 R3252
Q3000 100
L3000 2SD1616-TP-LK R3024 100
TP3001 R3201
IC3020 100
CXD9843AR
C3022
CN3000 C3000 R3006 R3003 0.1
C3002 100 1.5k R3001 C3026 0.1
2P 2.2k R3002
PH 0.1 16V 10k 10k R3202
100
R3004 C3027 0.1
1.2k ICT3096
ICT3001
53
R3026 1.5k
TP3023
C3021
C3001 47
16V
47
16V ICT3002
TP3000 Q3001 Q3002
2SC3052EF-T1-LEF 2SC3052EF-T1-LEF
C3028 C3029 C3030

0.1 0.1 0.1
52
HCD-DX375
50 50

HCD-DX375
Ver. 1.1
R3501 100
R3502 100
C3406
0.033
ICT3010
C3403
0.1 ICT3011
ICT3060 C3413
0.1
R3504 0
R3515 10
R3516 10
R3503
R3061
C3505
C3551 1 50V
C3503
10
0
0.1
R3403 10
0.1
TP3410
C3412
R3507 15k
C3500 0.1
ICT3061 100
ICT3047
R3404 0 35V
ICT3099
ICT3098
ICT3097
R3551
ICT3046
ICT3045
100k
ICT3049
TP3510
1SS355WTE-17
ICT3048
R3407 15k ICT3050
L3402
D3551
C3415 C3504
0.1
1
C3404 D3402
0.1 P6SMBJ33A-5 L3401
D3401 D3552
ICT3012 P6SMBJ33A-5 1SS355WTE-17
CXD9883M
C3506
C3507
0.033
0.033
IC3400
ICT3100
C3414 C3552
ICT3101 1 10 IC3500
R3401 50V CXD9883M
100 ICT3102
R3415 10
R3553
10k
ICT3013 C3409
R3402
100 C3400 0.1 100
ICT3070 C3420 0.0022
R3416 10 ICT3014 C3408 C3416 C3419 0.0022
0.1 2200
C3405 35V
0.1 ICT3069 R3420 2.7
C3508
C3513
ICT3015
0.1
0.1
C3306 C3407 ICT3071 R3419 2.7
P6SMBJ33A-5
0.033
P6SMBJ33A-5
0.033
D3502
ICT3016 C3418 0.0022
D3501
C3303
C3509
C3512
ICT3072 C3417 0.0022
35V
35V
100
100
0.1
L3501
L3502
C3313
C3516
ICT3017
2200
0.1
35V
C3514
R3303
C3515
10 TP3310
1
C3312
100
R3304 0 35V
R3307 15k L3302

C3315 EB3005
50 1 TERMINAL BOARD
R3519 R3520
C3519
C3520
0.0022
0.0022
C3304 D3302 2.7 2.7
R3322 10k
R3321 10k
R3324 10k
R3323 10k
R3422 10k
R3421 10k
R3424 10k
R3423 10k
C3517
C3518
0.0022
0.0022
0.1 P6SMBJ33A-5 L3301

D3301 ICT3065
ICT3066
ICT3018 P6SMBJ33A-5
CXD9883M
ICT3074 C3320 0.0022

ICT3068
ICT3067
IC3300
ICT3103 C3314
1 C3319 0.0022
ICT3104
ICT3073 R3320 2.7
ICT3105 C3423
0.001
R3315 10
ICT3075 R3319 2.7
ICT3019 C3309
100 C3318 0.0022
C3300 0.1 50V B 35V
C3422 CN3300
ICT3076 C3317 0.0022 0.001 2P
R3316 10 C3308 C3316 VH
0.1 2200 BOARD IN 60
C3305 35V
0.1
TP3304
C3256 C3307 TP3303

ICT3020
0.033 0.033
TP3302
C3253
ICT3021
TP3301
M
0.1 CN3400
C3263 Q3551 R3326 R3325 C3322 2P
ICT3022 0.1 2SC3052EF-T1-LEF R3555 0 100k 100k R3426 R3425 0.001 SCN
R3327 BOARD IN
100k 100k
100k R3427 60
R3253 10 100k
TP3250 C3262
R3254 0
100 R3554 C3323
ICT3051
35V 100k C3555 ICT3052 ICT3053 ICT3054 0.001

2.2
C3321 C3421
L3252 C3270 0.0022 2.2 10
R3257 15k C3265 ICT3078
1 C3269 0.0022
ICT3077
D3252 R3270 2.7 Q3302 Q3402
P6SMBJ33A-5 L3251 2SA1235TP-1EF 2SA1235TP-1EF
C3254
0.1 D3251
ICT3023 P6SMBJ33A-5 R3269 2.7 EB3004
CXD9883M
ICT3079 Q3301 TERMINAL BOARD

ICT3106 C3268 0.0022 Q3401
IC3250
ICT3080 2SA1235TP-1EF
C3264 2SA1235TP-1EF
ICT3107 1 C3267 0.0022
ICT3108
R3265 10
ICT3024 C3259
100
C3250 0.1 35V
R3266 10 ICT3025 C3258 C3266

0.1 2200
C3255 35V
0.1 B
ICT3026 C3257
0.033
53
HCD-DX375
51 51

HCD-DX375
Ver. 1.1
6-19. SCHEMATIC DIAGRAM – MAIN BOARD (3/6) – • See page 65 for Waveform. • See page 68 for IC Block Diagrams.
50
R3055
100
C3015 C3014
0.1 0.1
R3011 470
R3050
0 ICT3003
Q3081 ICT3004 R3012

RT1P141C TP3011 470
R3151
100
55 R3013
R3091 10k TP3012 C3013
22k 0.1
C3083 100p 50V CH R3087 22k
ICT3005
R3085 R3088 22k C3085 R3014 100 R3152
33k 1/10W 100p CH 100
R3015 100
R3101
C3092 0.1
R3092 TP3013 IC3010 100

R3098
22k
22k CXD9843AR
C3012
C3081 0.1
NJM4565M(TE2)
CN3001 470 C3087 R3095 C3016 0.1 F

4P
TP3081 10V 100p 2.2k R3102
IC3001
100
TP3082 C3017 0.1
R3099
C3090
22k
C3088 100
TP3083 100p 10V
TP3084 C3082 R3017 1.5k
470 C3089
10V 0.1
R3096 25V TP3014
2.2k F C3011
47
59 C3094 16V
100p
R3086
R3093
22k TP3015
5
33k C3020
C3095 R3089 22k C3086
0.001 100p 0.1
C3084 100p 50V CH R3090 22k R3094

22k C3019
0.1
C3018 TP3056
0.1
ICT3008
R3054
L3051 22 C3059 C3060
0.001 10p 53
ICT3006 ICT3007
ICT3009
FB3051 L3053
0
L3052
TK11118CSCL-G
R3053
SN74AHC1GU04DCKR
100
IC3050
L3054
C3052 1 10V
C3057
R3052 1M 1/10W
0.01
C3056
0.01 25V B
220
100 16V
CN3002
C3054
3P 10V X3051
IC3051
C3055
JST VH 3.96MM 49.152MHz

TP3053 SMD-49TB
C3091
220
16V C3053
0.001
TP3054 50V
B ICT3064 C3058 5p CH
C3051
0.1
50V
64 B
HCD-DX375
52 52

HCD-DX375
Ver. 1.1
MAIN
51
C3206
0.033
ICT3027
C3203 Q3252
0.1 ICT3028 2SA1235TP-1EF
C3213
0.1 Q3202
2SA1235TP-1EF
R3203
10 TP3210 C3212
100
35V
R3204 0
C3220 0.0022
R3207 15k C3215 ICT3082
C3272
1 C3219 0.0022 0.001
ICT3081 C3221 C3271
2.2 ICT3056 2.2
C3204 D3202 L3202 R3220 2.7
0.1 P6SMBJ33A-5 ICT3086 ICT3085
R3224 10k
R3223 10k
R3272 10k
R3271 10k
R3274 10k
R3273 10k
50 ICT3055
ICT3029 D3201 Q3251
P6SMBJ33A-5 L3201 ICT3083 R3219 2.7 Q3201 2SA1235TP-1EF
2SA1235TP-1EF C3273
CXD9883M
R3226 R3227 R3225 R3276 R3277 R3275 0.001

ICT3109 ICT3084 C3218 0.0022 100k 100k CN3200
IC3200
100k 100k 100k 100k

C3214 4P
ICT3110 1 C3217 0.0022 SCN
BOARD IN
ICT3111 TP3204
R3215 10 ICT3030
C3209 TP3203
100
35V
C3200 0.1 TP3202
R3216 10 C3208 TP3201
ICT3031 0.1 C3216
C3205 2200 C3223
0.1 35V 0.001 60
R3222
R3221
ICT3032
10k
10k
C3207
R3174 10k
R3173 10k
R3172 10k
R3171 10k
R3124 10k
R3123 10k
R3122 10k
R3121 10k
C3156
0.033 0.033
ICT3033 C3222
Q3152 0.001
C3153 ICT3034 Q3102 2SA1235TP-1EF C3172
0.1 2SA1235TP-1EF 0.001
C3163
0.1
CN3100
R3153 TP3150 4P
10
C3162 SCN
100 C3173 BOARD IN
R3154 0 35V Q3101 0.001
2SA1235TP-1EF
TP3104
ICT3089 TP3103
R3157 15k C3165 C3170 0.0022 Q3151
1 2SA1235TP-1EF TP3102
ICT3087
C3169 0.0022 C3171
C3154 D3152 L3152 ICT3088 ICT3058 2.2 TP3101
0.1 P6SMBJ33A-5 R3170 2.7 ICT3057 C3121
2.2 ICT3059 C3123
D3151 L3151 0.001 60
ICT3035 P6SMBJ33A-5
CXD9883M
ICT3090 R3169 2.7 R3125

R3177
IC3150
ICT3112 R3126 100k

C3164 C3168 0.0022 R3176 100k R3175
100k R3127 100k
ICT3113 1 100k 100k C3122
C3167 0.0022
ICT3114 ICT3091 0.001
R3165 10
C3159
ICT3036 100
35V
C3150 0.1
R3166 10 ICT3037 C3158
0.1 C3166
C3155 2200
0.1 35V
ICT3038
C3106 C3157
0.033 0.033
ICT3039 EB3003
C3103 TERMINAL BOARD
0.1
ICT3040
C3113
0.1
R3103
10 TP3110
C3112
100
R3104 0 35V
D3112 ICT3093 C3120 0.0022

R3107 15k P6SMBJ33A-5 C3115
1 C3119 0.0022
ICT3092 R3120 2.7
52 L3112
C3104
0.1 L3111
ICT3041 ICT3094 R3119 2.7
CXD9883M
IC3100
ICT3115 C3118 0.0022

C3114
ICT3116 D3111 1 ICT3095 C3117 0.0022
P6SMBJ33A-5
ICT3117
R3115 10
ICT3042 C3109
100
C3100 0.1 50V B 35V
EB3002
R3116 10 TERMINAL BOARD
ICT3043
C3116
C3105 C3108 2200
0.1 0.1 35V
ICT3044
C3107
0.033 50V B
HCD-DX375
53 53

HCD-DX375
6-21. SCHEMATIC DIAGRAM – MAIN BOARD (5/6) – • See page 65 for Waveform. • See page 70 for IC Pin Function Description.
R545 10k
ICT539
R554
10k
R550 1k
C519 0.1
R534
CN601 10k R540
15P 10k C518
TP605 R604 100 R501 0.1
1k
TP606 R605 100 ICT538
TP607 R606 100 R503 10k
TP608 R607 100 C504 0.01

TP609 R608 100
TP610 R609 100 C505

TP611 R610 100 0.01
25V
TP612 R611 100 B
TP613 R612 100
TP614 R613 100

TP615 R614 100
TP616 R558 10k
57
R601 0
TP617
TP618
R515 1k R559 10k

IC501
R516 1k M30622MEP
R504 47k TP504 -A61FPU0
TP503
55
R506 22k R507 4.7k
C501 R509 100 ICT547
0.1 R510 10k
R511 100
C502 R512 10k R560
0.1 10k
R513 100 C508 0.1
C503
0.1 R514
10k
C507
0.1 ICT537 4
C506 R508
0.1 1k
R502
10k R536
R524 0 R557 Q503 R563 IC503
10k 47k 2SC3052EF-T1-LEF 10k
PST3635NR
ICT541
R546 10k ICT542

R529 1k
R532 1k
R519
R528 10k
R531 10k
10k R562 C520

R520 10k
R539 47k 0.22

10k
R552 4.7k
R549 4.7k
C517
5MHz
0.1
X501
ICT546
1SS355WTE-17
ICT545
50
D501
R561 C523
R541 100k 0.1
R527 10k C521
10k 0.01
C515 C522
ICT540
0.1 R556 0.22

ICT544
ICT543
47k
55
HCD-DX375
54 54

HCD-DX375
6-22. SCHEMATIC DIAGRAM – MAIN BOARD (6/6) –
54
54
IC622
BH2210FV-E2
RB626 RB630
220 10k 50
TP646
TP645
TP644
TP643
52
R623 100 RB629
RB625 10k
220 FB504 0UH
C625 R634 C534 ICT550

0.1 220 0.1 FB506 0UH TP537
C532 EB505
0.1 FL502 TERMINAL BOARD
FB501 FB507
R633 100 0UH 0UH 0UH GROUND
TP536
CN622 C622 C535

21P 0.1 47
R635 10k D502 C531 0.1 16V
1SS355WTE-17
D504 C528 FB508
1SS355WTE-17 100 10V 0UH CN506
R628 R632 TP535
100 100 12P
R578 100 TP534
ICT549 R579 100 TP533
C526 C527 R580 100 TP532
IC621 100 2200
R621 BH2210FV-E2 10V 6.3V
100 TP531
RB624 RB628 C533 FB505 0UH

R622 10k 0.1 TP538
220 10k
ICT534 FL503
0UH
RB622 FB502 0UH FB509 0UH TP530
100
C536
47 16V
64
R575 1k
62 IC504
NJM2887DL3 C537 C538
R572 FL501 EMI
RB627 300k 0.001 0.001
10k
FB503 0UH FB510 0UH TP529

RB623 220 R631 220 C524 C525
RB621
100 R630 220 47 0.1 TP528 CN505
16V R573 C529 5P
100k 0.47 TP527 PIN-S-2.0
C623 C624 R629 BOARD IN
0.001 0.1 220
C621 TP554
0.1
TP553
TP552
TP551
EB501
TP550
CN501
23P
TP501 R517 100 R577 CN504 41
Q504 47k 11P
TP502 RSR025N03TL TP548
TP505 ICT551
R576
TP506 R518 100 1k
R584 100 TP547
TP507 TP546
TP508 R585 100 TP545
TP509 R586 100 TP544
TP510 R587 100 TP543
TP511 R521 100 R588 100 TP542
TP512 TP541
TP513 C509 1 10V B R589 100 TP540
TP514 TP539 44
C510 0.1
IC502
TP515 R526 1k TK11133CSCL-G CN503
C511 9P
0.001
TP516 R530 100 ICT536 R564 100

59
TP517 R533 100 ICT535 R565 100
TP518 R535 100 R566 100 TP524
TP519 R567 100 TP525
TP520
TP521 R568 100
TP522 R569 100 TP526
C516
TP523 1
CN502
4P
ICT548
HCD-DX375
55 55

HCD-DX375
6-23. PRINTED WIRING BOARD – I/O BOARD – • See page 33 for Circuit Boards Location. :Uses unleaded solder.
• Semiconductor
Location
COMPONENT
Ref. No. Location
VIDEO OUT
IC201 E-4
VIDEO Y CB/PB CR/PR IC352 D-8
IC353 C-7
MONITOR OUT TV VCR IC360 D-5
2 1
S VIDEO R L R L
Q353 E-7
(DVD ONLY) 4 3 Q354 E-8
Q360 E-10
Q361 C-10
Q362 C-11
R293
R339
R338 E E
IC353 R215
C215 C219
R220
R219
IC360 1 3
JR362
IC201 IC352
E
JR364
C218
E E
R224 R225
5
1
15 1
R216
C216
DMB12 BOARD
L B CN4301
E C AM
(Page 39) MAIN BOARD TUNER
JACK BOARD DMB12 BOARD
CN601 UNIT
CN402
(Page 48) CN4302 COAXIAL
(Page 58) (Page 39) FM75Ω
HCD-DX375
56 56

HCD-DX375
6-24. SCHEMATIC DIAGRAM – I/O BOARD – • See page 65 for Waveforms. • See page 69 for IC Block Diagrams.
CN203
9P
CN312
AMP-S 5P C345 R381 R382
TP353 C349 22 47k 47k
22
TP354 25V R356
4.7k
25V
TP355
C346
TP356 22 25V
TP357 C350 R357 R344 R386

4.7k
22 4.7k 47k R384
25V 47k
2SC3052EF
2SC3052EF
Q362
59 R343
Q361
4.7k
R349 R350 L201
10k 10k
CN311
15P
R254 100k
C234
R253 100k
C239 100
0.1 16V
C235 TP393
22 25V
Q360 R375 TP392
RT1P141C-TP-1 1k
R376 TP391
0
C236 TP390
R255 100k
R256 100k 22 25V

TP389
TP388
* TP387
L352 TP386
R370 10k
R369 1k
R368 10k
TP385
IC352 (5/6)
MC14052 BDR2 R367 1k R360 TP384
CN601
470 1/10W
C359 C352 TP383 54
0.1
1 B TP382
R338 C340 50V
22 25V 16
6.8k TP381
J200 C351
C333
R363 4.7k
2P 47
*
C334 0.1
100
16V 16V
TP361 R365
C354 47k
0.001
NJM4558M -TE2
TP362
R339
IC TA7809LS
TP363 6.8k
IC353
IC360
TP364 C341 R374 R358
R330 22 47k 47k
R366 47k
C337 22 25V
JR362
6.8k 25V
R364 4.7k
RT1N241C-TP-1
RT1N241C-TP-1
C339
0
C336 0.1
TP365 0.1
R385 C356
Q354
Q353
6.8k 220p C348

TP366 C338 1
100 16V
TP367 R331 R334 C355 C342 R378 R377 16V F
6.8k 6.8k 220p 22 47k 47k
25V
TP241 R216
C216 R220 R225
6.8k 47k CN202
C242 0.001 R215 220p 47k C362 R359 FFC-7P S
6.8k 22 25V 470
1/10W
J201 Y+C
C215 TP221
220p C219 JR364 C360
22 0 1 TP222
25V 50V
TP223
IC201 MM1623BFBE L202 TP224
C224 C218 R219 R224
22 47k C210 C209 TP225 DMB12
TP242 R241 1000 47k R228 470 10V 0.1
75 6.3V 25V 10k TP226
(1/7)
R234 100 TP227
CN4302
R229 C223 0.1 41
TP243 75
R230 C225
75 1000 6.3V C212 33p
C204 1 R204 1k TP203

J202 C213 TP204
3P 100
TP231 16V C203 1 TP205
C214 0.1 TP206
R231 C226
TP232 75 1000 6.3V R263 10k C202 1 TP207
R207
0 TP208
R232 C227
TP233 75 100 16V TP209 DMB12
TP234 C207 10 50V
R209
R235 100 0 TP210 (1/7)
R233 C228
75 100 16V
C205
C208 0.1 TP211 CN4301
0.001 TP212
41
TP235 C201 10 50V TP213

CN201
FFC-11P S
HCD-DX375
57 57

HCD-DX375
6-25. PRINTED WIRING BOARDS – PANEL SECTION – • See page 33 for Circuit Boards Location. :Uses unleaded solder.
MAIN BOARD
A CN501
(Page 48)
IC801 3 1
IC802
1 2
2 4 I/1
1 5
2
12 12
12 12
I/O BOARD
L CN312
(Page 56) FUNCTION > . x X H A
VOLUME
– +
1 5
E
10 1 IC803
E
DISC 5 DISC 4 DISC 3 DISC 1
E E DISC 2
E
E E E
E E E E E E
E
E
12
IC402 IC401
E
12
D493
D492
E E
E 4 1 12
12
• Semiconductor Location
Ref. No. Location Ref. No. Location Ref. No. Location
PHONES H AUDIO IN
D431 C-5 D814 G-14 Q473 H-6
MAIN BOARD
D432 C-5 D815 G-13 Q474 H-5
CN3001 D433 I-6 Q475 H-6
(Page 49) D470 G-7 IC401 H-5 Q476 H-7
D492 I-7 IC402 H-3 Q801 D-12
D493 I-7 IC801 B-7 Q802 C-9
D496 I-3 IC802 D-11 Q811 H-17
D497 I-3 IC803 H-12 Q812 H-17
D801 E-13 Q813 H-16
D802 E-13 Q450 I-4 Q814 H-16
D803 D-13 Q451 I-4 Q815 H-15
D804 D-13 Q460 I-3 Q816 H-15
D805 D-13 Q461 I-4 Q817 H-14
D811 G-17 Q470 H-6 Q818 H-13
D812 G-16 Q471 H-6 Q819 H-13
D813 G-15 Q472 H-7 Q820 H-12
HCD-DX375
58 58

HCD-DX375
6-26. SCHEMATIC DIAGRAM – PANEL SECTION – • See page 67, 69 for IC Block Diagrams.
Q814 Q815
RT1P141C-TP-1 RT1P141C-TP-1
R834 R835
470
330
R833 R836
470 330
D812 D813
SML79423C-TP15 SML79423C-TP15
R851 R852 R827 R828 R829 R830 R841
1k 2.2k 2.2k 4.7k 10k 22k 47k Q813 Q816
RT1P141C-TP-1 D814 RT1P141C-TP-1
Q812 SML79423C-TP15 Q817
RT1P141C-TP-1
RT1P141C-TP-1
D811
CNP807 SML79423C-TP15
CHASSIS GND R837
470
R832
S808 S807 S809 S810 S811 S812 S813 330
SW. KEY SW. KEY SW. KEY SW. KEY SW. KEY SW. KEY SW. KEY
BU2099FV
IC803
CN402 R838
TP418 MUTE FB475 0UH R831 330
S800 470
TP410 R-OUT FB420 0UH VOLUME KNOB
Q818
TP400 GND R854 R856 R857 D815 RT1P141C-TP-1
C819 C820 R853 2.2k R855 2.2k 2.2k Q811 SML79423C-TP15 Q819
TP409 L/MIC-OUT FB410 0UH 2.2k 1k RT1P141C-TP-1
0.01 0.01 RT1P141C-TP-1
TP402 9V 25V 25V
B B S802 S803 S804 S805 S806
SW. KEY SW. KEY SW. KEY SW. KEY SW. KEY
Q470 R839
RT1N441C -TP-1 470
R806 100
R807 100
R808 100
C849 0.1
57
R472 680
C471 Q475
TP415
2.5-3.3V
22 R479 RT1N441C R840 Q820

R471 0 R481
6.3V 2.2k 100k -TP-1 CN810 330 RT1P141C-TP-1
R413 1k R415 NO805
1k 10P
JR816 JR817 R414
0 0 R478 R412 C412 15k Q474
220 22k 47p
RT1P140C
C413 220p -TP-1
R482 10k
JR814
0
Q476 D470
1SS355W TE-17
RT1N140C
Q473 -TP-1
RT1P141C R477
FB470 0UH
4.7k
-TP-1 Q472 C411
2SK3018 10
TP413 -T106 R411
FB471 0UH
R401
Q471 * AU(L) 470 CN811

4.3k
RT1P141C AMP-L
-TP-1 10P
R480
NJM4558M -TE2
R470 R488 39
J401 2.2k 100k C401
R487
IC401
C410 100p
R410 100k
0 47
16V
100 10V
R402 4.7k
C403
C491
C420 100p
R420 100k
1000p D493
16V 1SS355WTE-17
JR813 0
D492
1SS355WTE-17 FL801
CNP401 TP414 R421 C421
CHASSIS GND AU(R) 470 10 R422 22k C422 47p C423 220p
R423 1k R424 1k
FB451
R451 22 R452 47 C434 R434 0 R433 3.3k
Q451 0.047 C432 47p C433 68p
R450 Q450 JR811
4.7k 2SC5938-T112-1B 2SC5938-T112-1B 0
R432 22k R435 1M
FB450 C832
0 R454 C431 TP416 R431 220p 50V B
4.7k 0.47 A.CAL 0
1SS355WTE-17
C450 R453 C826

FB472 0UH
J402 R492 R495 0.01 220p 50V B

D433
0 0 4.7k CNP801 C825

AMP-L 220p 50V B
2P
NJM4558M -TE2
FB479
TP837
C460 FB478 C405

TP851
IC402
0.01 0.1
TP879 MO/ST-DET
TP883 GAIN-CONT
TP881 PLUG-DET1
TP880 A.CAL-OUT
R463
TP878 DC-CONT
FB460
4.7k
TP882 PLUG-DET2
C493 0 R460 R464 S801

470p 4.7k SW. KEY
R820 100k
R461 4.7k FB461 C829
D497 22
D496 22
TP838
1SS355W
TP874
TP876
TP875
TP877
1SS355W TE-17 CN804 50V

CNP402 TE-17 Q460 Q461 R462 NO804 TP852
CHASSIS GND 2SC5938-T112-1B 2SC5938-T112-1B 47 2P BOARD-IN C823
220p 50V B
CN403 C822
TP422 FB474 0UH JR812 0 220p 50V B
TP423 C821
220p 50V B
TP420 C818
220p 50V B
C817
TP424 220p 50V B
CNP802 C816
NO802 220p 50V B
(3/6) 10P BOARD-IN C815
220p 50V B IC802
C813 PT6315
52 220p 50V B
C812
220p 50V B
CN805 IC801
AMP-L
1SS355W TE-17
CN801 10P NJL23H400A

TP863
23P C435
0.47
D432
FFC_1.0
TP862
TP854
TP860
TP859
TP858
TP856
TP855
TP861
TP857
L
TP801 R436
12k C809
TP802 10
TP803 R817 16V
R819 1k
C436 1 B
R437 15k
Q802
1SS355WTE-17
TP804 47
2SC3052EF-T1-LEF
D431
TP805
TP806
TP807 JR807 R816 100 1/10W
TP808 R815 100 1/10W
TP809 R814 100 1/10W R811
82k
TP810 1/10W
UDZS-TE-176.2B
C811
1SS355WTE-17
1SS355WTE-17
TP811 0.01 C814

10
R823 25V
D803
16V
0.1 16V
D804
D805
TP812 47 B
C804
C805
C802 47 50V
TP813 T801 D802 0.01

DC-DC CONVERTER 1SS355W 50V
TE-17
TP814 R804 L801
3.9k Q801
R802 100
TP815 C803 1/10W CPH5504-TL-E R801

0.0047 50V B
0.022 50V B
TP816 100 D801 33k

CN501 10V 1SS355W 1/10W
TE-17
C800
55
C801
TP817 FB806 0UH

R800
1k
TP818
TP819
TP820
TP821
TP822
TP823 L802 R805 0 2012
HCD-DX375
59 59

HCD-DX375
6-27. PRINTED WIRING BOARD – SPEAKER BOARD – • See page 33 for Circuit Boards Location. 6-28. SCHEMATIC DIAGRAM – SPEAKER BOARD –
:Uses unleaded solder.
EP301
EARTH PLATE
SPEAKER
(CHASSIS)
TB301
DICS 4P
NEW
FRONT R FRONT L CENTER WOOFER SUR R SUR L
CN301
C301 C313 EH-S 4P
1000p 10000P
(CHASSIS) C302 C314

1000p 10000P
(CHASSIS)
(4/6)
C303 C315
1000p 10000P
53
C304 C316
1000p 10000P
1 4 1 6
C305 C317
1000p 10000P CN302
VH-S 2P
C306 C318
1000p 10000P
(2/6)
C319
C307 10000P
1000p 51
I K J M C308 C320
1000p 10000P
MAIN MAIN MAIN
BOARD MAIN
BOARD BOARD
CN3100 BOARD TB302
CN3200 CN3400 DICS 2P
(Page 49) CN3300 NEW
(Page 49) (Page 49)
(Page 49)
CN303
C309 C321 EH-S 6P
1000p 10000P
C310
1000p C322
10000P
(4/6)
C311 C323
1000p 10000P
53
C312
1000p C324
10000P
M
EP302
EARTH PLATE (2/6)
4
51
(CHASSIS)
HCD-DX375
60 60

HCD-DX375
6-29. PRINTED WIRING BOARDS – CD MECHANISM SECTION – • See page 33 for Circuit Boards Location. :Uses unleaded solder.
• Semiconductor
MOTOR BOARD S761 Location
(SUB TRAY OUT) Ref. No. Location
D701 D-4
D711 D-4
IC701 D-4
IC711 E-3
IC751 B-6
CN761 Q751 D-2
6 1
M761 M762 12 SENSOR BOARD

1-861-240- (12)
(LD/ST MOTOR) (BU U/D MOTOR) 3 IC751
1 12
CN751 (12)
1-861-244-
JW701 SW(1) BOARD
CN705
1
CN706
6
3
CN721
CN702
3
1 S721
1 3
1 (MAIN TRAY IN/OUT)
12
1-861-241-
(12)
IC701
C761
S781 1
SW(2) BOARD
ROTARY ENCODER RELAY BOARD S731
C762
(ST U/D) (SUB TRAY N)
R702
4 1
R712
4 3 G 2 1 D701
D711
3
1
JW713
G 2
2 R701
G JW702 CN731
1 JW705 3
Q751 4 R711
9 JW716 1-861-242- 12
JW708 JW718 CN707 JW703
(12)
R751 JW707 JW704
IC711
JW717
R754 JW709
ENCODER BOARD
1 R753 JW706 JW720
JW710 9 C701
JW712
S771
R752
R755
2
JW711 ROTARY ENCODER
JW719
CN701 JW715 CN771

CN703 (MD)
C702 JW714 2
20
21 1
12
1-861-245- (12)
MAIN 12
D BOARD 1-861-243- (12)
CN622
(Page 48)
HCD-DX375
61 61

HCD-DX375
6-30. SCHEMATIC DIAGRAM – CD MECHANISM SECTION – • See page 69 for IC Block Diagrams.
IC701
BA6956AN
S721
CN702 CN721 (MAIN TRAY
3P 3P IN/OUT)
M761
RF500TB
CN761 C761 R702
6P CN706
0.01 100 C701
6P 47
16V
R701
M762 680
CN701
RF500TB C762 21PIN
0.01
D701
MTZJ-T-77-4.7B
IC711
BA6956AN
S761
(SUB TRAY OUT)
BU ST-E1
ST-E2 D
ST-E3
ST-E4
(6/6)
S731 CN731 CN703 CN622
(SUB TRAY IN) 2P 2P
(Page 55)
C702
10
16V
R712 R711 ST-E4 S781
100 680 ST-E3 ROTARY
ENCODER
D711 ST-E2
MTZJ-T-77-4.3A ST-E1
IC751
IC751
RPR-359F D SENSOR
R751 R753
CN751 CN705 91 10k
3P 3P S771
ROTARY ENCODER
R754 Q751 (MD)
12k 2SC1740S-QRT CN707 CN771
DISC SENSOR 5P 5P
R752
10k R755
10k
HCD-DX375
62 62

HCD-DX375
6-31. PRINTED WIRING BOARD – POWER BOARD – • See page 33 for Circuit Boards Location. :Uses unleaded solder.
• Semiconductor
Location
Ref. No. Location
8
D901 B-11
IC921
6
K A IC901 D905 B-5
D906 A-6
4 2 D907 A-7
D908 B-5
3 E 5
D909 C-8
1
E 1 3 D910 A-5
D913 B-5
D914 C-8
D915 B-7
3 4 D921 B-3
D922 B-2
PC902 D923 B-1
D924 C-1
D925 A-1
2 1 D926 B-2
D931 F-6
D932 E-8
PC903 3 4 EB905 D941 D-2
3 4
PC901 D942 E-2
D943 D-3
D944 D-2
D945 F-2
2 2 1
IC901 B-6
K A IC921 B-3
IC951 IC931 E-9
IC941 G-2
K A
IC931 IC942 G-3
IC943 G-4
E E
IC951 D-1
PC901 D-9
PC902 C-1
PC903 D-8
Q901 B-5
Q921 B-1
Q943 E-8
S
Q945 F-3
Q947 E-8
5 1 5 1 5 1 A K A
IC942
R974
IC941 IC943
12
12 1 1 3
12
(CHASSIS) (CHASSIS)
F G
MAIN BOARD AC IN
MAIN BOARD CN3002
CN506 (Page 49)
(Page 49)
HCD-DX375
63 63

HCD-DX375
6-32. SCHEMATIC DIAGRAM – POWER BOARD –
(CHASSIS)
D931
C938 FCU20UC20
EB905 330p
250V CN902
TP903 WIRE 3P
CN901 FH901 FH902 TH901 T901

2P C963 THERMISTOR
TP901 HOLDER
FUSE
HOLDER
FUSE
D901
D5SBA60F01
C930
100p
MAIN TRANS L931 R931 R940 R937 TP904
0.0022 LF902 3.3k 10k 10k
250V
LF901 C920 R965
FR901
0.01 0.1 5.6k
TP902 F901 250V 1W C937
0.047 R933 R932 C934 D932 (3/6)
C964 C902 50V 33k C936 C939
0.22 C905 R903 R904 4.7k 0.1 2200 0.1 UDZSTE-175.1B
0.0022 35V
275V 0.01 50V 50V
250V
C903 FR902 33k 33k 52
0.1 400V 3W 3W
1000 1W C933 R936 470k
C901 C935 C932 2200
0.22 C918 200V R938
R902 C913 D913 0.1 2200 35V 1k
3.3M 275V 0.01 SARS03 35V Q943
VDR901 100p
VARISTOR 250V 250V RT1N441C-TP-1
TNR14SE471K490 IC931 R939
TA76431AS
EB901 (TPE6) 3.3k
EB902 R905
D905 10
D1NL20U-TR2 Q947
RT1N441C-TP-1
Q901
(CHASSIS) EB903
IC931
(CHASSIS) 2SB1116A TP-LK
(CHASSIS)
D914 PC901 R949

1k
D908 1SS355WTE-17
1SS355WTE-17 D906
C906 C908 C911 1SS355WTE-17
3300p 47 0.0047 R910
1.5kV 2.2k
35V 50V D907 R906 D915
3.3k
1SS355WTE-17 UDZSTE-1710B PC901
TLP421F(D4-GR)
C909 R909
C907 R919 100k
220p R911 0.0015 18k
50V 220
R907 R935 R934
IC901 10k 1k 1k
STR-F6138-LF1352
R908 C910
R914 R913 3.3k
PC903
IC901 0.05
5W
0.22
2W
R912
0.22
1/2W 10
50V TLP421F(D4-GR)
2W
D909
1SS355WTE-17
IC941
PC903
TP908
R946 150
TP910
R943 0 TP909
R941 0
TP907
R948
10k
PC902 IC943
SI-3033KM-TL
C943 100 16V

IC942
SI-3050KM-TL
IC941
SI-3120KM-TL
C949
PC902 100 C947
TLP421F(D4-GR) R956 10V 100
1k 10V
1/10W
C969
UDZSTE-1720B
IC921 0.1 C948

470
C955
0.1
D945
10V 25V
C945 C954 C942 C951
C970 470 0.1 C971 470 0.1
0.1 16V 25V 0.1 25V 25V
R966 TP913
IC921 1k 1/10W
STR-V153 R929
2.2
D910 1/2W L942 L945 R967 TP912
1SS355WTE-17 1k 1/10W
T902 C953
IC943 IC942 R971 0
CN904
R925 R969 SUB TRANS 0.001 2kV R968 TP917 WIRE 12P
10 1k 1k 1/10W
D923 D941 TP914

UDZSTE-1710B EK19LF-F7 C941 C960
1000 0.1
ST02D-140
25V
D921
L951 L948
D925 D944 L941 R955 R951
D926 UDZSTE EK19LF-F7 470 220
UDZSTE -175.1B
-1710B
L947 R958
R954 R952 Q945 1k
C968 0.1
D942 C967 C944 C946 22k 2.2k RSR025N03TL

Q921 RK36LF-B3 0.1 2200 1000 R957
2SD1616A -TP-LK 47k
D922 16V 16V C952
D1NL20U D943 0.047 50V R974
-TR2 RK36LF-B3 3.3k TP915
C925 C929 C923 C924 R922 IC951 CN506

R927 0.1 0.0047 2.2 R926 D924 R923 C922 C958 C940 C976 TP916
47p 4.7 TA76L431S (TPE6,Q)
2kV 0.82 50V 50V 50V 680k UDZSTE 4.7k 22 0.1 3300 R953 100 55
1W -1724B 100V 10V 3.9k 16V
TP911 TP918
EB904
IC951
C928
220p
250V
(CHASSIS)
HCD-DX375
64 64

HCD-DX375
• Waveforms
– DMB12 Board – – I/O Board –
1 IC101 6 (DVDRFIP) 6 IC201 wd (CVBS) 9 IC201 w; (CYOUT)

2.5 Vp-p
2.0 Vp-p
H
800 mVp-p H
200 mV/DIV, 100 ns/DIV 1 V/DIV, 20 µs/DIV 1 V/DIV, 20 µs/DIV
2 IC101 <xx. (XTALI) 7 IC201 wh (COUT) 0 IC201 qk (CbOUT)
4.0 Vp-p
H 1.8 Vp-p 1.3 Vp-p

37 ns H
1 V/DIV, 10 ns/DIV 1 V/DIV, 20 µs/DIV 500 mV/DIV, 20 µs/DIV
3 IC708 qg (X1) 8 IC201 wa (YOUT) qa IC201 qh (CrOUT)

2.1 Vp-p
H
3.8 Vp-p 1.5 Vp-p
100.0 ns H
1 V/DIV, 40 ns/DIV 1 V/DIV, 20 µs/DIV 500 mV/DIV, 20 µs/DIV
– MAIN Board –
4 IC501 qg (Xin)
2.7 Vp-p
200 ns
1 V/DIV, 100 ns/DIV
5 IC3010 rk (XFSOIN)
5.5 Vp-p
20.3 ns
1 V/DIV, 10 ns/DIV
65
HCD-DX375
• IC Block Diagrams
– DMB12 Board –
IC706 BR24L16F-WE2
VCC 8 1 A0
16 K bit EEPROM ARRAY
11 bit 8 bit
WP 7 2 A1
ADDRESS SLAVE WORD DATA
11 bit
DECODER ADDRESS REGISTER REGISTER
START STOP
SCL 6 3 A2
CONTROL CIRCUIT
ACK
HIGHT VOLTAGE POWER SUPPLY

SDA 5 GENERATOR VOLTAGE DETECTION 4 GND
IC4601 PCM1803DBR
Single-End 5 th Order
VINL 1 Delta-Sigma 20 MODE1
/Differential
VINR 2 Converter Modulator 19 MODE0
Serial
VERF1 3 Interface 18 FMT1
VERF2 4 17 FMT0
× 1/64 (× 1/128)
Decimation
Filter
Reference
with
DC Cut Filter
Mode/
Format
Control
Single-End 5 th Order
/Differential Delta-Sigma
Converter Modulator
VCC 5
Power Supply
AGND 6
16 OSR
Clock and Timing Control
PDWN 7 15 SCKI
BYPAS 8
14 VDD
13 DGCD
FSYNC 9 12 DOUT
LRCK 10 11 BCK
66
HCD-DX375
– DMB12 Board –
IC702 TK11118CSCL-G IC150, IC705 SN74LVC1G08DCKR
VOUT
VIN
A 1 5 Vcc
5 4
B 2
OVER HEAT &
OVER CURRENT
PROTECTION
GND 3 4 Y
CONTROL
CIRCUIT
BANDGAP
REFERENCE
1 2 3
VCONT
GND
NP
– FL Board –
IC802 PT6315
SEG24/GRID5
SEG23/GRID6
SEG22/GRID7
SEG21/GRID8
SEG20/GRID9
GRID1
GRID2
GRID3
GRID4
VDD
VSS
44 43 42 41 40 39 38 37 36 35 34
Grid driver
Multiplexed driver
33 SEG19/GRID10
Command decoder
LED1 1
32 SEG18/GRID11
LED2 2
4-bit latch
12-bit shift register
LED3 3 Display memory

24 bits x 12 words 31 SEG17/GRID12
LED4 4
Data selector
OSC 5 OSC 30 VEE

Timing generator
key scan
24-bit output latch
DOUT 6
29 SEG16/KS16
DIN 7 Key data memory
Serial (2 x 16 bits) 28 SEG15/KS15
interface
CLK 8 27 SEG14/KS14
STB 9 26 SEG13/KS13
25 SEG12/KS12
segment driver 24 SEG11/KS11

KEY1 10
KEY2 11 23 SEG10/KS10
12 13 14 15 16 17 18 19 20 21 22
VSS
VDD
SEG1/KS1
SEG2/KS2
SEG3/KS3
SEG4/KS4
SEG5/KS5
SEG6/KS6
SEG7/KS7
SEG8/KS8
SEG9/KS9
67
HCD-DX375
– MAIN Board –
IC3100, IC3150, IC3200, IC3250, IC3300, IC3400, IC3500 CXD9883M
BST_A 1 36 PVDD_A
Over
Current
GVDD_A Fault
2 35 PVDD_A
/OTW 3 VREG 34 PVDD_A

Gate
/HIZ_HS_A Drive
/SD 4 33 PGND
/HIZ_LS_A
Stuck
Detect
/RESET 5 32 PGND
Protection
Logic
PWM_A 6 Timing 31 PGND
Control
Programmable /OCH_A
OC_ADJ 7 30 OUT_A
Current sense /OCL_A Gate
Drive
GND 8 29 OUT_A
/RESET_A
Temperature
Protection waming/error
AGND 9 and Over 28 OUT_A
Reset /HIZ_HS_X Current
Logic /HIZ_LS_X /UVP Fault
VREG 10 /OCH_X 27 OUT_B
/OCL_X Over
Current
M3 11 /RESET_X VREG Fault 26 OUT_B
Under GVDD_A
OLP Voltage
M2 12 OTP /PCR Power-Up Protection GVDD_B 25 OUT_B
CB3C Reset Gate
/UVP Drive
M1 13 /HIZ_HS_B 24 PGND
/UVP_VREG /HIZ_LS_B
PWM_B 14 Timing
Protection 23 PGND
Control
VREG Logic
VDD 15 Stuck 22 PGND
REG Detect
/OCH_B
GND 16 /OCL_B 21 PVDD_B
Gate
Drive
GVDD_B 17 20 PVDD_B
/RESET_B
BST_B 18 19 PVDD_B
Over
Current
Fault
IC3010, IC3020, IC3030 CXD9788AR

HPOUTR1
HPOUTR2
HPOUTL2
HPOUTL1
HPVDDR
HPVDDL
HPVSSR
HPVSSL
FSOCKO
XFSOIN
XVDD
FSOI
48 47 46 45 44 43 42 41 40 39 38 37
Sampling Rate
Converter
Filter
Liner
PWM ∆ ∑ Converter Gain &
Interpolator LOW DF2 DF1 S P
Control
CUT
Filter
36 XFSIIN
Clock Generator Clock Generator 35 DVDD
(Secondary Clock System) INIT/MUTE Serial Control (Primary Clock System) 34 TEST
33 BFVSS
32 BFVDD
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
OUTL1
OUTR1
XVSS
OUTR2
VSSR
VSSL
VDDL
XFSOOUT
NSPMUTE
SOFTMUTE
SCDT
SCLATCH
OVF FLAGR
OVF FLAGL
DATA
MCKSEL
VSUBC
VDDR
XOVDD
DVSS
PGMUTE
SCSHIFT
SFLAG
INIT
BCK
VSSR
XOVSS
DVDD
OUTL2
VSSL
LRCK
68
HCD-DX375
– I/O Board –
IC201 MM1623BFBE IC352 MC14052BDR2
S-DC OUT
28 VCC2
S1/S2
27 S-DC OUT
150kΩ 75Ω
VCC1 1 BIAS 6.75MHz DRIVER
LOW-PASS
C IN 2 6dB 26 C OUT
FILTER
MUTE 1 3
25 S1
CLAMP –6dB + 6dB
24 S2
CVBS IN 4 6dB 75Ω
6.75MHz DRIVER
YC MIX 5
LOW-PASS
23 CVBS OUT
FILTER
75Ω 22 GND2
CLAMP 6.75MHz DRIVER
LOW-PASS
Y IN 6 6dB 21 Y OUT
FILTER
GND1 7
BIAS 8 BIAS
I/P 9
6.75MHz
LOW-PASS 75Ω
DRIVER
FILTER
CY IN 10 6dB 20 CY OUT
LOW-PASS
150kΩ FILTER
CLAMP BIAS 13.5MHz
CLP 11 19 GND2
6.75MHz
150kΩ 75Ω
BIAS LOW-PASS
DRIVER
FILTER
CB IN 12 6dB 18 CB OUT
LOW-PASS
FILTER
MUTE2 13 13.5MHz
17 GND2
6.75MHz
150kΩ 75Ω
BIAS LOW-PASS
DRIVER
FILTER
CR IN 14 6dB 16 CR OUT
LOW-PASS
FILTER
13.5MHz 15 GND2
– LED Board – – RELAY Board –

IC803 BU2099FV IC701, IC711 BA6956AN
VDD
Q11
Q11
Q10
OE
Q9
Q8
Q7
Q6
Q5
20 19 18 17 16 15 14 13 12 11
TSD
12 BIT
CONTROL
SHIFT
CIRCUIT
REGISTER
OUTPUT
12 BIT BUFFER CONTROL LOGIC
STORAGE (OPEN DRAIN)
REGISTER
1 2 3 4 5 6 7 8 9
1 2 3 4 5 6 7 8 9 10
VREF
OUT2
RNF
OUT1
VM
VCC
FIN
GND
RIN
VSS
NC
DATA
CLK
LCK
Q0
Q1
Q2
Q3
Q4
69
HCD-DX375
Ver. 1.1
• IC Pin Function Description

MAIN BOARD IC501 M30622MEP-A61FPU0 (SYSTEM CONTROLLER)
Pin No. Pin Name I/O Description
DAMP_SCDT/
1 O DAMP processor and Diat data output
DIAT_SDATA
DAMP_SHIFT/
2 O DAMP processor and Diat clock output
DIAT_SCLK
3 DSP_INTR I DSP interrupt (not used)
4 SIRCS_IN I Sircs input
5 DSP_MOSI/DIR_DIN O DSP and DIR data output (not used)
6 DSP_MISO I DSP data input (not used)
7 DSP_SPICLK/DIR_CLK O DSP/DIR clock output (not used)
8 BYTE I External data bus (Ground terminal)
9 CNVSS I Change processor mode (Pull down)
10 EN_A/DAMP FSDLY I Volume control for ENCODER (Pull up)
11 EN_B/FL_RESET I Volume control for ENCODER (Pull up)
12 RESET I System reset signal input
13 XOUT O Crystal output for main clock (5MHz)
14 VSS — Ground terminal
15 XIN I Crystal input for main clock (5MHz)
16 VCC — Power supply (BUP+3.3V)
17 NMI I BUP +3.3V
18 DIR_ZERO I DIR zero data detect (not used)
DIR_CSFLAG/A.CAL
19 I Out level detect for auto calibration
_OUT_LEVEL
20 AC_CUT I Detect AC-CUT
21 FL_CLK/LED_CLK O FL and LED driver clock output
22 LED_LAT O LED driver latch
23 DIAT_CSOD I DIAT CSOD signal input (not used)
24 FL_D_OUT/LED_DATA O FL and LED driver data output
25 FL_CS/STB O FL driver chip select
26 MIC_GAIN O MIC gain control
27 CDM_OPEN_SW I CDM open switch input
28 DC_CONT O A.CAL MIC DC control output
29 I2C_CLK I/O I2C clock input
30 I2C_DATA I/O I2C data input
31 DVD_SID O Media Tek data out/Flash write TXD1
32 DVD_SOD I Media Tek data in/Flash write RXD1
33 DVD_SCO I Media Tek clock in/Flash write CLK1
34 DVD_XIFBUSY O Media Tek busy request/Flash write RTS1
XM_SC_TX_OUT/
35 O MIC detect status out to Media Tek (not used)
MIC_DET_OUT
XM_SC_RX_IN/
36 I KARAOKE mode information from Media Tek (not used)
KARAOKE MODE
37 DVD XIFCS I Media Tek chip select
38 MTK RST O Media Tek reset
39 P_CONT1 O Control for power supply 1
42 DRIVE_RST (EN) O DAMP driver reset
70
HCD-DX375
Ver. 1.1

43 DRIVE_OCP (DIAG) I DAMP driver shut down
44 OVERFLOW1 I DAMP processor F/C/S over flow detect
45 OVERFLOW2 I DAMP processor SW over flow detect
46 CE I Flash write CE (not used)
47 DAMP LATCH1 O DAMP processor latch1
50 DAMP INIT O DAMP processor reset
51 DAMP SOFT MUTE O DAMP processor soft muting
52 HP_SW I Head phone detect
53 HP_MUTE O Head phone muting
54 SRC_MUTE O Sampling rate converter mute control (not used)
55 DSP_RESET O DSP reset (not used)
56 DSP_SPIDS O DSP device select (not used)
57 SEL_SA-CD O DSP input data select (not used)
58 DSP_RST O DIR reset (not used)
59 DSP_HCE O DIR chip enable (not used)
DAMP OUT2DLY/
60 I DAMP OUT 2DLY select switch
DIR_ERR
DAMP FSDLY/
61 I DAMP FSDLY select switch
DIR_XSTATE
62 VCC — Power supply (BUP 3.3V)
63 DIR_HDOUT I DIR data in (not used)
65 DIAT_XRST O DIAT reset (not used)
66 DIAT_XSCEN O DIAT chip enable (not used)
67 SRC_MODEO O Sampling rate convertor MODEO control (not used)
68 M_ST O LINK (Multi STEREO) control
69 TUNED I TUNER tuned input
70 ST_CLK O TUNER clock output
71 ST_DO I TUNER data input
72 ST_CE O TUNER chip enable
73 ST_DI O TUNER data output
74 KEY INT I Wakeup from ECO mode by Power key input
RDS_CLK/MIC_CLK/
75 O not used
XM_ERR_IRQ
RDS-DATA/MIC-DAT/
76 O not used
XM_COM_SEL
77 XM_RESET O XM reset (not used)
78 DABSEL/XMSEL O XM clock select (not used)
79 V_SEL0 O VIDEO selector 0
81 TVSEL/V_SEL3 O TV / VIDEO selector 3 (not used)
82 A_SEL0 O Audio selector 0
83 A_SEL1 O Audio selector 1
85 IO_CE O I/O expander IC chip enable
86 IO_RESET O I/O expander IC reset
87 IO_DI O I/O expander IC data output
71
HCD-DX375

88 IO_DO I I/O expander IC data input
89 IO_CLK O I/O expander IC clock output
90 MONO/ST_DET I Front jack MONO or STEREO detect
A.CAL MIC LEVEL/
91 I MIC level detect for auto calibration
A_SEL2
92 DESTINATION I Destination select input
93 MODEL I Model select input
94 KEY2 I Key input 2 input
98 VREF — Reference voltage (BUP+3.3V)
99 VCC — Power supply (BUP+3.3V)
100 MIC/A.CAL SW I MIC insert switch
72
HCD-DX375
DMB12 BOARD IC101 CXD9804R

(CD/DVD RF AMP, FOCUS/TRACKING ERR AMP, DVD SYSTEM PROCESSOR, DIGITAL SERVO PROCESSOR)
1 AGND — Ground terminal
2 DVDA I AC coupled input path A
3 DVDB I AC coupled input path B
4 DVDC I AC coupled input path C
5 DVDD I AC coupled input path D
6 DVDRFIP I AC coupled DVD RF signal input RFIP
7 DVDRFIN I AC coupled DVD RF signal input RFIN (not used)
8 MA I DC coupled main-beam RF signal input A
9 MB I DC coupled main-beam RF signal input B
10 MC I DC coupled main-beam RF signal input C
11 MD I DC coupled main-beam RF signal input D
12 SA I DC coupled sub-beam RF signal input A (not used)
13 SB I DC coupled sub-beam RF signal input B (not used)
14 SC I DC coupled sub-beam RF signal input C (not used)
15 SD I DC coupled sub-beam RF signal input D (not used)
16 SDFON I CD focusing error negative input (not used)
17 SDFOP I CD focusing error positive input (not used)
18 TNI I 3 beam satellite PD signal negative input
19 TPI I 3 beam satellite PD signal positive input
20 MDI1 I Laser power monitor input
21 MDI2 I Laser power monitor input
22 LDO2 O Laser driver output
23 LDO1 O Laser driver output
24 SVDD3 — Power supply (RF+3.3V)
25 CSO O Central servo, positive main beam summing output (not used)
26 RFLVL O RFRP low pass, or Positive main beam summing output (not used)
27 SGND — Ground terminal
28 V2REFO O Reference voltage 2.8V
29 V2O O Reference voltage 2.0V
30 VREFO O Reference voltage 1.4V
31 FEO O Focus error monitor output (not used)
32 TEO O Tracking error monitor output (not used)
33 TEZISLV O TE slicing level (not used)
34 OPOUT O Op amp output (not used)
35 OP_INN I Op amp negative input (not used)
36 OP_INP I Op amp positive input (not used)
37 DMO O Disk motor control output. PWM output
38 FMO O Feed motor control. PWM output
39 TROPENPWM O Tray PWM output/tray open output.
40 IOPMON I Power monitor signal input
41 TRO O Tracking servo output
42 FOO O Focus servo output
43 USB_VSS — Ground terminal
44 USBP — USB port DPLUS analog pin (not used)
45 USBM — USB port DMINUS analog pin (not used)
46 USB_VDD3 — Power supply (SW+3.3V)
47 SPFG I Motor hall sensor input
73
HCD-DX375

48 MSW I Mute signal control output
49 CKSW — Not used
50 OCSW — Not used
51 EEWP O WF signal output to EEPROM (IC103)
52 DVDD18 — Power supply (+1.8V from IC110)
53 to 59 HA 2 to 8 O Address bus 2 to 8 output to FLASH ROM (IC102)
60, 61 HA18, 19 O Address bus 18, 19 output to FLASH ROM (IC102)
62 DVSS — Ground terminal
63 APLLCAP I APLL external capacitance connection
64 APLLVSS — Ground terminal
65 APLLVDD3 — Power supply (+3.3V from IC105)
66 XWR O WE signal output to FLASH ROM (IC102)
67 to 72 HA 16 to 11 O Address bus 16 to 11 output to FLASH ROM (IC102)
73 DVDD3 — Power supply (SW+3.3V)
74, 75 HIGHA 10, 9 O Address bus 10, 9 output to FLASH ROM (IC102)
76 HA20 O Address bus 20 output to FLASH ROM (IC102)
77 XROMCS O CE signal output to FLASH ROM (IC102)
79 XRD O OE signal output to FLASH ROM (IC102)
81 to 84 HD 0 to 3 I Data bus 0 to 3 input from FLASH ROM (IC102)
86 to 88 HD 4 to 6 I Data bus 4 to 6 input from FLASH ROM (IC102)
90 ALE O Address latch enable (not used)
91 HD7 I Data bus 7 input from FLASH ROM (IC102)
95 UWR I System controller write strobe (not used)
96 URD I System controller read strobe (not used)
98 IFSDO O DVD SOD signal output to system controller (IC501)
99 IFSCK O DVD SCO signal output to system controller (IC501)
100 XIFCS I DVD XIFCS signal input from system controller (IC501)
101 IFSDI I VIFBUSY signal input from system controller (IC501)
102 SCL O SCL signal output to EEPROM (IC103)
103 SDA O SDA signal output to EEPROM (IC103)
104 TRG-SW O RS232 RXD signal output (not used)
105 XRST O RS232 reset signal output
106 RXD I RD232 RXD clock
107 TXD I RD232 TXD data
109 ICE I ICE mode enable (not used)
110 XSYSRST I MTRST signal input from system controller (IC501)
111 IR I IR control signal input (not used)
112 XTXINT I External interrupt0 (not used)
113 DQMO O DQM0 signal output to SD-RAM (IC104)
114 XIFSSY I DQM signal input
74
HCD-DX375

115 RD7 I Data bus 7 from SD-RAM (IC104)
117, 118 RD 6, 5 I Data bus 6, 5 from SD-RAM (IC104)
120, 121 RD 4, 3 I Data bus 4, 3 from SD-RAM (IC104)
123 to 125 RD 2 to 0 I Data bus 2 to 0 from SD-RAM (IC104)
128 RD 14 I Data bus 14 from SD-RAM (IC104)
129 to 133 RD 13 to 9 I Data bus 13 to 9 from SD-RAM (IC104)
136 LIMITSW I LIMSW signal input
137 DQM1 O DQM1 signal output to SD-RAM (IC104)
138 RWE O WE signal output to SD-RAM (IC104)
139 CAS O CAS signal output to SD-RAM (IC104)
140 RAS O RAS signal output to SD-RAM (IC104)
142 RCS O RCS signal output to SD-RAM (IC104)
143 BA0 O BAO signal output to SD-RAM (IC104)
145 BA1 O BA1 signal output to SD-RAM (IC104)
146 RA10 O Address bus 10 output to SD-RAM (IC104)
149 to 151 RA 1 to 3 O Address bus 1 to 3 output to SD-RAM (IC104)
153 RVREF — Reference voltage (not used)
154 RCLKB — Dram clock (not used)
156 DRCLK O CLK signal output to SD-RAM (IC104)
157 CKE O CKE signal output to SD-RAM (IC104)
168 to 172 SMPTE_Y (7) to Y (3) O VIDEO signal output to HDMI Driver (IC701)
174 SMPTE_Y (2) O VIDEO signal output to HDMI Driver (IC701)
176 to 177 SMPTE_Y (1) to Y (0) O VIDEO signal output to HDMI Driver (IC701)
178 VCLK O System clock output
179 WIDE I Wide switch signal input
180 ADSCK — Not used
181 TSD_M O TSDM signal output to Motor Driver (IC201)
75
HCD-DX375

183 MUTE O MUTE signal output to Motor Driver (IC201)
184 MUTE123 O MUTE123 signal output to Motor Driver (IC201)
185 REW O REW signal output to Motor Driver (IC201)
186 FWD O FWD signal output to Motor Driver (IC201)
187 ADSD0 O Not used
188 XDACS O Not used
189 DAVCC — Power supply (+3.3V from IC105)
190 DACVDDC I Bandgap reference voltage (not used)
191 FS O Full scale adjustment (pull down)
192 CIN — Not used
193 DAVSS — Ground terminal
194 YUV1 O Y signal output to VIDEO AMP (IC201)
195 DAVDD — Power supply (+3.3V from IC105)
196 YUV2 O CHROMA signal output to VIDEO AMP (IC201)
198 YUV3 O VIDEO signal output to VIDEO AMP (IC201)
199 DAVDD — Power supply (+3.3V from IC105)
200 YUV4 O Y signal output to VIDEO AMP (IC201)
202 YUV5 O Cb signal output to VIDEO AMP (IC201)
203 YUV6 O Cr signal output to VIDEO AMP (IC201)
205 VSYN O Active low vertical sync output to HDMI Driver (IC701)
206 YUV7 — Not used
207 SMBSY O Active low horizontal sync output to HDMI Driver (IC701)
208 SMSCK O SMS clock output
209 SMSDI I Audio data of SPDIF input
210 SMSDO O SMS data output
211 XSMCS O SMS CS output
213 ALRCK O Audio left/right channel clock
214 ABCK O Audio bit clock
215 ACLK O Audio DAC master clock
217 ASDATA0 O Audio serial data 0
220 SPDATA — Not used
221 DVDD18 — Power supply (+1.8V)
224 GPIO — Not used
225 SDPIF O SPDIF output (not used)
226 RFGND18 — Ground terminal
227 RFVDD18 — Power supply (RF+1.8V)
228 XTALO O Oscillator output signal (27MHz)(not used)
229 XTALI I Oscillator input signal (27MHz)
230 JITFO O RF jitter meter output (not used)
231 JITFN I Negative input of operation amplifier for RF jitter meter (not used)
76
HCD-DX375

232 PLLVSS — Ground terminal
233 IDAC — Not used
234 PLLVDD3 — Power supply (RF+3.3V)
235 LPFON O Negative output of loop filter amplifier
236 LPFIP I Positive input of loop filter amplifier
237 LPFIN I Negative input of loop filter amplifier
238 LPFOP O Positive output of loop filter amplifier
239 VDD3 I Power supply (RF+3.3V)
240 VCM I Not used
242 VREFP — Not used
243 VREFN — Not used
244 RFVDD3 — Power supply (RF+3.3V)
245 RFRPDC I RFRP signal input
246 RFRPAC I RFRP signal input
247 HRFZC I High frequency RF ripple zero crossing
248 CRTPLP O Defect level filter capacitor connecting
249 RFGND — Ground terminal
250 CEQP — Not used
251 CEQN — Not used
252 OSP O RF offset cancellation capacitor connecting
253 OSN I RF offset cancellation capacitor connecting
254 RFGC O RF offset loop capacitor connecting for DVD-ROM
255 IREF I Current reference input (not used)
256 AVDD3 — Power supply (RF+3.3V)
77
HCD-DX375
SECTION 7
EXPLODED VIEWS
NOTE:
• -XX and -X mean standardized parts, so they • The mechanical parts with no reference
The components identified by mark 0 or
may have some difference from the original number in the exploded views are not supplied.
dotted line with mark 0 are critical for safety.
one.
Replace only with part number specified.
• Items marked “*” are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when
ordering these items. 3
11 not
supplied 3
7-1. OVERALL SECTION
12
8
3
9
3
7
#1 not
supplied
#5
#1
b #1
a
7 #1 #9
6 #1 #3
5 b
3
not
4 supplied
10
not
supplied
front panel section
chassis section
a
2
1
Therefore, if the mounted DMB12 board (A-1148-813-A) is replaced,
3 exchange new EEP ROM (IC103, IC706) with that used before the
2 replacement.
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
1 2-653-086-01 PANEL, LOADING 10 1-787-331-11 FAN, D.C.
2 4-232-478-41 FOOT
3 3-077-331-21 +BV3 (3-CR) 11 1-828-292-11 WIRE (FLAT TYPE) (5 CORE)
4 1-828-953-11 WIRE (FLAT TYPE) (9 CORE) 12 1-828-319-11 WIRE (FLAT TYPE) (11 CORE)
5 1-693-703-11 TUNER (FM/AM) (TM10SU) #1 7-685-646-79 SCREW +BVTP 3X8 TYPE2 IT-3
#3 7-685-881-09 SCREW +BVTT 4X8 (S)
6 A-1176-128-A I/O BOARD, COMPLETE #5 7-685-871-01 SCREW +BVTT 3X6 (S)
7 3-363-099-51 SCREW (CASE 3 TP2)
8 2-653-945-01 CASE #9 7-682-547-04 SCREW +B 3X6
✩9 A-1148-813-A DMB12 BOARD, COMPLETE
Note: If the wire (flat type) was replaced, fold it some as the
wire (flat type) before replacement.
78
HCD-DX375
7-2. FRONT PANEL SECTION
not 72
supplied
61 71
not
supplied not
60 supplied
59 70
61
61
69
66
not
supplied 65
63 66
58 67
62 68 61
57 66
56 61
55
54 64
including 52 53
S800
51
51 2-654-836-01 KNOB (VOL) 62 2-653-091-01 BUTTON (DISC)
52 2-654-835-01 RING (VOL) 63 2-653-094-01 INDICATOR (DISC)
53 2-653-097-01 ORNAMENT (RIGHT) 64 A-1148-824-A JACK BOARD, COMPLETE
54 2-653-096-01 ORNAMENT (PLAY) 65 2-653-093-01 BUTTON BASE (PLAY)
55 2-653-098-01 WINDOW, INDICATION
66 2-653-089-01 CAP (FUNC)
56 2-664-622-01 SHEET (WINDOW), ADHESIVE 67 2-653-088-01 CAP (PLAY)
57 2-653-095-01 ORNAMENT (POWER) 68 2-653-090-01 CAP (AMS)
58 2-653-085-51 PANEL, FRONT 69 A-1148-823-A LED BOARD, COMPLETE
59 2-653-087-01 CAP (POWER) 70 A-1148-821-A FL BOARD, COMPLETE
60 2-653-092-01 BUTTON, BASE (POWER)
71 1-828-384-11 WIRE (FLAT TYPE) (23 CORE)
61 3-087-053-01 +BVTP2.6 (3CR) 72 3-531-576-01 RIVET
Refer to “Precaution when replacing the CAP” when

replacing the CAP (PLAY) or CAP (FUNC) or CAP (AMS)
or CAP (POWER). (See page 6)
79
HCD-DX375
7-3. CHASSIS SECTION

#1
#1
101 not
not supplied supplied
not
supplied
105 #2
106
104
not
103 supplied
113
114
101 101
112
102
107
101
115
F901 not
supplied
109
DVD mechanism
deck section 108 110
101
not
supplied
not supplied
#4
111
101 3-077-331-21 +BV3 (3-CR) 111 4-232-478-41 FOOT
102 1-828-319-11 WIRE (FLAT TYPE) (11 CORE) 112 4-059-585-01 TIE, CABLE
103 1-828-370-11 WIRE (FLAT TYPE) (21 CORE) 113 2-597-972-51 SHEET, RADIATION
104 1-828-985-11 WIRE (FLAT TYPE) (15 CORE) 114 2-597-972-11 SHEET, RADIATION
105 1-828-310-11 WIRE (FLAT TYPE) (9 CORE) 115 1-828-774-51 WIRE (FLAT TYPE) (24 CORE)
106 3-077-331-01 +BV3 (3-CR) 0 F901 1-532-749-11 FUSE, GLASS TUBE (8A/125V)
107 A-1148-794-A MAIN BOARD, COMPLETE #1 7-685-646-79 SCREW +BVTP 3X8 TYPE2 IT-3
108 A-1146-005-A POWER BOARD, COMPLETE #2 7-685-648-79 SCREW +BVTP 3X12 TYPE2 IT-3
0 109 1-830-190-11 CORD, POWER #4 7-685-647-79 SCREW +BVTP 3X10 TYPE2 IT-3
110 3-703-244-00 BUSHING (2104), CORD
80
HCD-DX375
7-4. DVD MECHANISM DECK SECTION-1 (CDM81C-DVBU101)
161
165
164 156
163
#6
160
162 #6
159
158 #8
not supplied
157
#8
155
#8
152 #6
151 #6
154
153
151 4-251-849-01 LEVER (SW2) 160 4-251-829-02 TRAY (SUB)
152 4-251-991-01 SPRING (SW2), TORSION
153 4-251-860-01 LEVER (LOCK) 161 4-985-672-01 SCREW (+PTPWH M2.6), FLOATING
154 4-251-867-01 SPRING (LOCK), TORSION 162 4-251-923-01 YOKE (310)
155 4-251-828-01 TRAY (MAIN) 163 4-251-821-03 BRACKET (TOP)
164 4-251-922-01 PULLEY B (310), CHUCKING
156 4-251-822-01 JOINT (LIFTER) 165 4-251-824-01 LIFTER
157 4-251-857-01 COVER (R)
158 4-251-830-01 SLIDER (ST) #6 7-685-534-19 SCREW +BTP 2.6X8 TYPE2 N-S
159 4-251-858-01 COVER (L) #8 7-685-102-19 SCREW +P 2X4 NON-SLIT TYPE 2
81
HCD-DX375
#7
#7
#7 #7
214 214
209
#7 #7
not supplied 203
#6 203
203 204 215
#6
not supplied
M761
M762
206 #7
210
213 211
208 212 #7
#7
208 #7 #7
S771
#7
205
208 not supplied
#7
202 not supplied
201
207 #6
#6
#6
201 4-251-870-01 BELT (BU) 211 4-251-854-01 GEAR (BU1)
202 4-251-869-01 BELT (MAIN TRAY) 212 4-251-850-01 GEAR (MAIN TRAY 1)
203 4-251-841-01 GEAR (SUB TRAY 1) 213 4-251-856-01 GEAR (BU2)
204 4-251-873-01 SPRING (MODE), COMPRESSION 214 4-251-842-01 GEAR (SUB TRAY 2)
205 4-239-618-01 SCREW (+PWH, 2X6), STEP TAPPING 215 4-251-851-01 GEAR (MAIN TRAY 2)
206 4-251-872-01 SPRING (LEVER), TORSION M761 A-4713-174-A MOTOR (81) ASSY (LD/ST MOTOR)
207 4-251-868-01 BELT (SUB TRAY) M762 A-4713-174-A MOTOR (81) ASSY (BU U/D MOTOR)
208 4-251-853-01 PULLEY (BU) S771 1-478-552-11 ENCODER, ROTARY (MD)
209 4-251-834-01 LEVER (MAIN TRAY) #6 7-685-534-19 SCREW +BTP 2.6X8 TYPE2 N-S
210 4-251-852-01 GEAR (MAIN TRAY 3) #7 7-685-902-21 SCREW +PTPWH 2.6X8 (TYPE2)
82
HCD-DX375
not supplied
251
CDM81C-DVBU101
261
256
251
#7 #7
#7 #7 #7
259
262 264
253
272 263
273 262 263
252 270
#6
not supplied
265 #7
257 262
#6
not supplied
263
S781
267
251
258 252 266
#6
#6
#7 255
268 #7
#7 271
#7 254 260
269 #6 272
not supplied
251
251 4-985-672-01 SCREW (+PTPWH M2.6), FLOATING 265 4-251-823-01 CHASSIS (CDM81)
252 4-251-873-01 SPRING (MODE), COMPRESSION
253 4-251-874-02 SPRING (SW), TENSION 266 A-4750-232-A RELAY BOARD, COMPLETE
254 4-251-844-01 GEAR (SS2) 267 4-239-618-01 SCREW (+PWH, 2X6), STEP TAPPING
255 4-251-835-01 GEAR (STOCKER 1) 268 4-251-825-01 CAM (BU)
269 4-251-832-01 LEVER (STOCKER)
256 4-251-833-01 LEVER (SUB TRAY) 270 4-251-861-01 LEVER (SW)
257 4-251-843-01 LEVER (RELEASE)
258 4-251-831-02 LEVER (MODE) 271 4-251-839-01 GEAR (STOCKER 4)
259 4-251-862-01 SHUTTER (TRAY) 272 4-251-840-01 GEAR (SUB TRAY)
260 4-251-845-01 GEAR (SS3) 273 4-251-847-01 GEAR (SS4)
S781 1-478-551-11 ENCODER, ROTARY (ST U/D ENCORDER)
261 4-251-829-02 TRAY (SUB) #6 7-685-534-19 SCREW +BTP 2.6X8 TYPE2 N-S
262 4-251-827-01 CAM (STOCKER)
263 4-251-836-01 GEAR (STOCKER 2) #7 7-685-902-21 SCREW +PTPWH 2.6X8 (TYPE2)
264 4-251-838-01 GEAR (STOCKER 3)
83
HCD-DX375
7-7. BASE UNIT (DVBU101)
303
304
304 302
303
301 303
304
304
303
#6
#6
301 X-4956-097-1 HOLDER (310) ASSY 304 3-087-599-01 INSULATOR SCREW
0 302 8-820-291-02 OPTICAL PICK-UP (KHM-310CAB/C2RP) #6 7-685-534-19 SCREW +BTP 2.6X8 TYPE2 N-S
303 2-634-618-01 INSULATOR
84
HCD-DX375
SECTION 8
DMB12
ELECTRICAL PARTS LIST
NOTE:
• Due to standardization, replacements in the • COILS
parts list may be different from the parts uH: µH When indicating parts by reference number,
specified in the diagrams or the components • RESISTORS please include the board name.
used on the set. All resistors are in ohms.
• -XX and -X mean standardized parts, so they METAL: Metal-film resistor. The components identified by mark 0 or
may have some difference from the original METAL OXIDE: Metal oxide-film resistor. dotted line with mark 0 are critical for safety.
one. F: nonflammable Replace only with part number specified.
• Items marked “*” are not stocked since they • SEMICONDUCTORS
are seldom required for routine service. In each case, u: µ, for example:
Some delay should be anticipated when uA. . : µA. ., uPA. . : µPA. .,
ordering these items. uPB. . : µPB. ., uPC. . : µPC. .,
• CAPACITORS uPD. . : µPD. .
uF: µF
✩ A-1148-813-A DMB12 BOARD, COMPLETE C153 1-162-917-11 CERAMIC CHIP 15PF 5% 50V
********************** C154 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C155 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
< CAPACITOR >
C101 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C157 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C102 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V C158 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C105 1-128-994-21 ELECT CHIP 47uF 20% 10V C160 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C112 1-128-994-21 ELECT CHIP 47uF 20% 10V
C117 1-124-779-00 ELECT CHIP 10uF 20% 16V
C120 1-165-908-11 CERAMIC CHIP 1uF 10% 10V C176 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C121 1-165-908-11 CERAMIC CHIP 1uF 10% 10V C177 1-128-994-21 ELECT CHIP 47uF 20% 10V
C122 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C130 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C187 1-126-208-21 ELECT CHIP 47uF 20% 4V
C131 1-125-889-91 CERAMIC CHIP 2.2uF 10% 10V C190 1-128-994-21 ELECT CHIP 47uF 20% 10V
C138 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C198 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C139 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C141 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C205 1-164-230-11 CERAMIC CHIP 220PF 5% 50V
C142 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C206 1-164-230-11 CERAMIC CHIP 220PF 5% 50V
C150 1-124-779-00 ELECT CHIP 10uF 20% 16V
C152 1-162-917-11 CERAMIC CHIP 15PF 5% 50V C217 1-126-204-11 ELECT CHIP 47uF 20% 16V
replacement.
85
HCD-DX375
Ver. 1.1
DMB12
C218 1-124-779-00 ELECT CHIP 10uF 20% 16V < CONNECTOR >
CN101 1-815-763-32 CONNECTOR, FFC/FPC 24P
C220 1-124-779-00 ELECT CHIP 10uF 20% 16V * CN105 1-770-470-21 PIN, CONNECTOR (PC BOARD) 6P
C221 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V CN109 1-784-370-21 CONNECTOR, FFC/FPC 11P
C222 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V * CN201 1-770-470-21 PIN, CONNECTOR (PC BOARD) 6P
C224 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V CN601 1-779-993-11 PIN, CONNECTOR (PWB) 5P
CN701 1-818-086-21 HDMI CONNECTOR (HDMI OUT (DVD ONLY))
C602 1-128-994-21 ELECT CHIP 47uF 20% 10V CN1701 1-573-806-21 PIN, CONNECTOR (1.5MM) (SMD) 6P
C603 1-128-994-21 ELECT CHIP 47uF 20% 10V CN4301 1-784-370-21 CONNECTOR, FFC/FPC 11P
< FERRITE BEAD >
C707 1-128-993-21 ELECT CHIP 22uF 20% 10V FB106 1-469-324-21 FERRITE, EMI (SMD) (2012)
C709 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V FB107 1-469-324-21 FERRITE, EMI (SMD) (2012)
FB112 1-469-670-21 FERRITE, EMI (SMD) (2012)
< FLUORESCENT INDICATOR >
C726 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V FL601 1-234-177-21 FILTER, CHIP EMI
FL703 1-234-177-21 FILTER, CHIP EMI
C731 1-128-993-21 ELECT CHIP 22uF 20% 10V
C736 1-126-208-21 ELECT CHIP 47uF 20% 4V
< IC >
C1104 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V IC101 6-706-727-01 IC CXD9804R
C1105 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V IC102 6-806-675-01 IC S29AL032D70TF-CHI1-0611UC
C1106 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V ✩ IC103 not supplied IC BR24L64F-WE2
C1107 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V IC104 6-707-897-01 IC EDS6416AHTA-75-E
IC105 6-702-302-01 IC TK11133CSCL-G
C4501 1-117-370-11 CERAMIC CHIP 10uF 10V IC107 6-702-302-01 IC TK11133CSCL-G
C4502 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V IC110 6-707-739-01 IC MM1661JTRE
C4504 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V IC111 6-704-100-01 IC TC7PAU04FU (TE85R)
C4601 1-117-370-11 CERAMIC CHIP 10uF 10V IC150 6-703-046-01 IC SN74LVC1G08DCKR
IC201 6-704-524-01 IC FAN8036L
C4603 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V IC701 6-708-682-01 IC CXD9873Q
C4605 1-128-994-21 ELECT CHIP 47uF 20% 10V IC702 6-702-300-01 IC TK11118CSCL-G
C4606 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V IC703 6-702-302-01 IC TK11133CSCL-G
C4607 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V IC705 6-703-046-01 IC SN74LVC1G08DCKR
✩ IC706 not supplied IC BR24L16F-WE2
C4608 1-124-779-00 ELECT CHIP 10uF 20% 16V
C4609 1-124-779-00 ELECT CHIP 10uF 20% 16V IC707 6-705-337-01 IC TK11150CSCL-G
C4610 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V IC708 6-806-298-01 IC MB95F108ASPFV-GE1-H0601
C4611 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V IC4502 6-703-589-01 IC SN74LVC1G125DCKR
C4621 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V IC4601 6-707-608-01 IC PCM1803DBR
replacement.
86
HCD-DX375
DMB12
< COIL >
R154 1-216-864-11 SHORT CHIP 0
L3601 1-469-555-21 INDUCTOR 10uH R155 1-216-864-11 SHORT CHIP 0
L4602 1-469-555-21 INDUCTOR 10uH R156 1-216-809-11 METAL CHIP 100 5% 1/10W
R159 1-216-805-11 METAL CHIP 47 5% 1/10W
< LINE FILTER > R160 1-216-805-11 METAL CHIP 47 5% 1/10W
* LF701 1-813-308-11 COMMON MODE CHOKE R161 1-216-805-11 METAL CHIP 47 5% 1/10W
* LF702 1-813-308-11 COMMON MODE CHOKE R162 1-216-864-11 SHORT CHIP 0
* LF703 1-813-308-11 COMMON MODE CHOKE R163 1-469-118-21 FERRITE, EMI (SMD) (1608)
* LF704 1-813-308-11 COMMON MODE CHOKE R164 1-216-864-11 SHORT CHIP 0
R165 1-469-118-21 FERRITE, EMI (SMD) (1608)
< TRANSISTOR >
R166 1-216-864-11 SHORT CHIP 0
Q101 6-550-008-01 TRANSISTOR UM6K1N-TN R167 1-469-118-21 FERRITE, EMI (SMD) (1608)
Q102 6-550-653-01 TRANSISTOR QST8TR R169 1-216-864-11 SHORT CHIP 0
Q103 8-729-027-52 TRANSISTOR RT1N241C-TP-1 R170 1-216-833-11 METAL CHIP 10K 5% 1/10W
Q701 8-729-012-57 TRANSISTOR 2SK1399-T1B R171 1-216-809-11 METAL CHIP 100 5% 1/10W
Q702 8-729-012-57 TRANSISTOR 2SK1399-T1B
R172 1-216-864-11 SHORT CHIP 0
< RESISTOR > R173 1-216-864-11 SHORT CHIP 0
R174 1-216-864-11 SHORT CHIP 0
R101 1-216-809-11 METAL CHIP 100 5% 1/10W R175 1-216-864-11 SHORT CHIP 0
R102 1-216-295-91 SHORT CHIP 0 R183 1-216-805-11 METAL CHIP 47 5% 1/10W
R103 1-216-864-11 SHORT CHIP 0
R105 1-216-833-11 METAL CHIP 10K 5% 1/10W R184 1-216-805-11 METAL CHIP 47 5% 1/10W
R189 1-218-827-11 METAL CHIP 150 0.5% 1/10W
R107 1-216-833-11 METAL CHIP 10K 5% 1/10W R190 1-218-827-11 METAL CHIP 150 0.5% 1/10W
R108 1-216-857-11 METAL CHIP 1M 5% 1/10W R191 1-216-821-11 METAL CHIP 1K 5% 1/10W
R109 1-216-864-11 SHORT CHIP 0
R110 1-216-841-11 METAL CHIP 47K 5% 1/10W R192 1-218-827-11 METAL CHIP 150 0.5% 1/10W
R111 1-216-809-11 METAL CHIP 100 5% 1/10W R193 1-216-821-11 METAL CHIP 1K 5% 1/10W
R195 1-218-827-11 METAL CHIP 150 0.5% 1/10W
R112 1-211-977-11 METAL CHIP 22 0.5% 1/10W R197 1-218-827-11 METAL CHIP 150 0.5% 1/10W
R113 1-211-977-11 METAL CHIP 22 0.5% 1/10W R204 1-216-822-11 METAL CHIP 1.2K 5% 1/10W
R114 1-216-845-11 METAL CHIP 100K 5% 1/10W
R115 1-211-977-11 METAL CHIP 22 0.5% 1/10W R205 1-216-833-11 METAL CHIP 10K 5% 1/10W
R116 1-216-821-11 METAL CHIP 1K 5% 1/10W R206 1-216-833-11 METAL CHIP 10K 5% 1/10W
R207 1-216-826-11 METAL CHIP 2.7K 5% 1/10W
R120 1-216-801-11 METAL CHIP 22 5% 1/10W
R123 1-216-864-11 SHORT CHIP 0 R212 1-216-833-11 METAL CHIP 10K 5% 1/10W
R213 1-218-867-11 METAL CHIP 6.8K 5% 1/10W
R130 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
R220 1-216-821-11 METAL CHIP 1K 5% 1/10W
R135 1-216-833-11 METAL CHIP 10K 5% 1/10W R221 1-218-889-11 METAL CHIP 56K 0.5% 1/10W
R138 1-216-809-11 METAL CHIP 100 5% 1/10W
R226 1-218-889-11 METAL CHIP 56K 0.5% 1/10W
R143 1-216-805-11 METAL CHIP 47 5% 1/10W
R145 1-216-864-11 SHORT CHIP 0 R232 1-218-877-11 METAL CHIP 18K 0.5% 1/10W
R146 1-216-805-11 METAL CHIP 47 5% 1/10W R233 1-218-883-11 METAL CHIP 33K 0.5% 1/10W
R234 1-216-833-11 METAL CHIP 10K 5% 1/10W
R147 1-216-864-11 SHORT CHIP 0 R246 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R151 1-216-833-11 METAL CHIP 10K 5% 1/10W
R152 1-216-864-11 SHORT CHIP 0 R701 1-216-864-11 SHORT CHIP 0
87
HCD-DX375
DMB12
R703 1-216-864-11 SHORT CHIP 0
R704 1-216-864-11 SHORT CHIP 0 R1101 1-218-855-11 METAL CHIP 2.2K 0.5% 1/10W
R705 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R1102 1-218-827-11 METAL CHIP 150 0.5% 1/10W
R1110 1-216-826-11 METAL CHIP 2.7K 5% 1/10W
R709 1-216-821-11 METAL CHIP 1K 5% 1/10W R1115 1-216-864-11 SHORT CHIP 0
R712 1-216-809-11 METAL CHIP 100 5% 1/10W
R714 1-216-864-11 SHORT CHIP 0 R1120 1-469-118-21 FERRITE, EMI (SMD) (1608)
R718 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R1121 1-469-118-21 FERRITE, EMI (SMD) (1608)
R1122 1-469-118-21 FERRITE, EMI (SMD) (1608)
R722 1-216-833-11 METAL CHIP 10K 5% 1/10W R1123 1-469-118-21 FERRITE, EMI (SMD) (1608)
R723 1-216-833-11 METAL CHIP 10K 5% 1/10W R1124 1-469-118-21 FERRITE, EMI (SMD) (1608)
R724 1-216-864-11 SHORT CHIP 0
R1133 1-216-864-11 SHORT CHIP 0
R730 1-218-840-11 METAL CHIP 510 0.5% 1/10W R1134 1-216-864-11 SHORT CHIP 0
R734 1-216-864-11 SHORT CHIP 0
R1141 1-216-864-11 SHORT CHIP 0
R743 1-216-821-11 METAL CHIP 1K 5% 1/10W
R744 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R1145 1-216-295-91 SHORT CHIP 0
R745 1-216-821-11 METAL CHIP 1K 5% 1/10W R1150 1-216-827-11 METAL CHIP 3.3K 5% 1/10W
R1151 1-216-827-11 METAL CHIP 3.3K 5% 1/10W
R749 1-216-824-11 METAL CHIP 1.8K 5% 1/10W
R750 1-216-824-11 METAL CHIP 1.8K 5% 1/10W R1168 1-216-813-11 METAL CHIP 220 5% 1/10W
R1170 1-216-864-11 SHORT CHIP 0
R754 1-216-864-11 SHORT CHIP 0
R1179 1-216-809-11 METAL CHIP 100 5% 1/10W
R760 1-216-809-11 METAL CHIP 100 5% 1/10W R1183 1-216-813-11 METAL CHIP 220 5% 1/10W
R763 1-216-864-11 SHORT CHIP 0
R1191 1-216-864-11 SHORT CHIP 0
R766 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R1201 1-216-827-11 METAL CHIP 3.3K 5% 1/10W
R769 1-216-864-11 SHORT CHIP 0
R1503 1-216-864-11 SHORT CHIP 0
R780 1-216-864-11 SHORT CHIP 0
R1706 1-216-821-11 METAL CHIP 1K 5% 1/10W
R785 1-216-864-11 SHORT CHIP 0
R787 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R1751 1-216-833-11 METAL CHIP 10K 5% 1/10W
R2504 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R790 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
88
HCD-DX375
DMB12 FL
R4505 1-216-864-11 SHORT CHIP 0 A-1148-821-A FL BOARD, COMPLETE
R4506 1-216-864-11 SHORT CHIP 0 ******************
R4507 1-216-864-11 SHORT CHIP 0
< CAPACITOR >
R4510 1-469-311-22 BEAD, FERRITE (CHIP) (1608)
R4511 1-469-311-22 BEAD, FERRITE (CHIP) (1608) C435 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16V
R4512 1-400-244-11 BEAD, FERRITE (CHIP) (1608) C436 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
C802 1-119-943-91 ELECT 47uF 20% 50V
R4516 1-469-311-22 BEAD, FERRITE (CHIP) (1608)
R4520 1-216-864-11 SHORT CHIP 0 C803 1-124-584-00 ELECT 100uF 20% 10V
R4527 1-216-864-11 SHORT CHIP 0 C804 1-162-974-11 CERAMIC CHIP 0.01uF 50V
R4601 1-216-809-11 METAL CHIP 100 5% 1/10W C805 1-164-360-11 CERAMIC CHIP 0.1uF 16V
R4602 1-216-809-11 METAL CHIP 100 5% 1/10W C809 1-126-157-11 ELECT 10uF 20% 16V
R4603 1-216-833-11 METAL CHIP 10K 5% 1/10W
R4605 1-216-864-11 SHORT CHIP 0 C812 1-162-960-11 CERAMIC CHIP 220PF 10% 50V
R4611 1-216-809-11 METAL CHIP 100 5% 1/10W
R4619 1-115-416-11 CERAMIC CHIP 0.001uF 5% 25V C817 1-162-960-11 CERAMIC CHIP 220PF 10% 50V
R4621 1-216-809-11 METAL CHIP 100 5% 1/10W C821 1-162-960-11 CERAMIC CHIP 220PF 10% 50V
R4702 1-216-864-11 SHORT CHIP 0
R4718 1-216-864-11 SHORT CHIP 0 < CONNECTOR >

R4801 1-216-864-11 SHORT CHIP 0
R4802 1-216-864-11 SHORT CHIP 0 CN801 1-779-560-21 CONNECTOR, FFC (LIF (NON-ZIF)) 23P
R4803 1-216-864-11 SHORT CHIP 0 CN805 1-785-336-11 PIN, CONNECTOR (LIGHT ANGLE) 10P
R4805 1-216-864-11 SHORT CHIP 0 CN811 1-785-336-11 PIN, CONNECTOR (LIGHT ANGLE) 10P
< COMPOSITION CIRCUIT BLOCK > < CONNECTOR >
RB103 1-234-400-21 CONDUCTOR, NETWORK (2010X4) CNP801 1-785-328-11 PIN, CONNECTOR (LIGHT ANGRE) 2P
RB104 1-234-400-21 CONDUCTOR, NETWORK (2010X4)
RB105 1-234-371-21 RES, NETWORK 47 (1005X4) < DIODE >
RB106 1-234-371-21 RES, NETWORK 47 (1005X4)
RB107 1-234-400-21 CONDUCTOR, NETWORK (2010X4) D431 6-501-193-01 DIODE 1SS355WTE-17
D432 6-501-193-01 DIODE 1SS355WTE-17
RB110 1-234-400-21 CONDUCTOR, NETWORK (2010X4) D803 8-719-069-56 DIODE UDZSTE-176.2B
D805 6-501-193-01 DIODE 1SS355WTE-17
RB114 1-234-400-21 CONDUCTOR, NETWORK (2010X4) < FERRITE BEAD >
RB116 1-234-371-21 RES, NETWORK 47 (1005X4) FB806 1-414-813-11 FERRITE, EMI (SMD) (2012)
RB117 1-234-371-21 RES, NETWORK 47 (1005X4)
< SWITCH >
FL801 1-519-852-11 FLUORESCENT INDICATOR
S1701 1-771-337-21 SWITCH, SLIDE (NOM, DL)
< IC >
< VIBRATOR >
IC801 6-600-349-21 IC NJL23H400A
X101 1-795-630-11 VIBRATOR, CRYSTAL 27MHz IC802 8-759-643-83 IC PT6315
X701 1-795-244-11 VIBRATOR, CERAMIC 10MHz
*************************************************************
89
HCD-DX375
FL I/O
< SHORT > C228 1-126-933-11 ELECT 100uF 20% 16V
C234 1-126-382-11 ELECT 100uF 20% 16V
JR807 1-216-296-11 SHORT CHIP 0 C235 1-104-662-91 ELECT 22uF 20% 25V
C236 1-104-662-91 ELECT 22uF 20% 25V
< COIL >
C239 1-164-156-11 CERAMIC CHIP 0.1uF 25V
L801 1-410-671-31 INDUCTOR 47uH C242 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
L802 1-410-671-31 INDUCTOR 47uH C333 1-126-933-11 ELECT 100uF 20% 16V
< TRANSISTOR > C336 1-164-156-11 CERAMIC CHIP 0.1uF 25V
Q801 6-550-065-01 TRANSISTOR CPH5504-TL-E C337 1-104-662-91 ELECT 22uF 20% 25V
Q802 8-729-120-28 TRANSISTOR 2SC3052EF-T1-LEF C338 1-126-933-11 ELECT 100uF 20% 16V
< RESISTOR > C340 1-104-662-91 ELECT 22uF 20% 25V
C341 1-104-662-91 ELECT 22uF 20% 25V
R436 1-216-834-11 METAL CHIP 12K 5% 1/10W
R437 1-216-835-11 METAL CHIP 15K 5% 1/10W C342 1-104-662-91 ELECT 22uF 20% 25V
R802 1-216-809-11 METAL CHIP 100 5% 1/10W C348 1-127-573-11 CERAMIC CHIP 1uF 10% 16V
C349 1-126-796-11 ELECT 22uF 20% 25V
R804 1-216-828-11 METAL CHIP 3.9K 5% 1/10W
R814 1-216-809-11 METAL CHIP 100 5% 1/10W C352 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
R816 1-216-809-11 METAL CHIP 100 5% 1/10W
R817 1-216-821-11 METAL CHIP 1K 5% 1/10W C356 1-162-960-11 CERAMIC CHIP 220PF 10% 50V
< TRANSFORMER > < CONNECTOR >
T801 1-443-645-11 TRANSFORMER, DC CONVERTER CN201 1-779-279-11 CONNECTOR, FFC (LIF (NON-ZIF)) 11P
************************************************************* CN202 1-779-273-11 CONNECTOR, FFC (LIF (NON-ZIF)) 5P
CN203 1-568-828-11 CONNECTOR, FFC 9P
A-1176-128-A I/O BOARD, COMPLETE CN311 1-779-283-11 CONNECTOR, FFC (LIF (NON-ZIF)) 15P
******************* CN312 1-785-317-11 PIN, CONNECTOR (STRAIGHT) 5P
< CAPACITOR > < IC >
C201 1-126-964-11 ELECT 10uF 20% 50V IC201 6-705-602-01 IC MM1623BFBE

C202 1-115-156-11 CERAMIC CHIP 1uF 10V IC352 8-759-385-76 IC MC14052 BDR2
C203 1-115-156-11 CERAMIC CHIP 1uF 10V IC353 8-759-100-96 IC NJM4558M-TE2
C204 1-115-156-11 CERAMIC CHIP 1uF 10V IC360 6-703-550-01 IC TA7809LS
< JACK >
C207 1-126-964-11 ELECT 10uF 20% 50V
C208 1-164-156-11 CERAMIC CHIP 0.1uF 25V J200 1-794-212-11 JACK, PIN 4P (TV, VCR)
C209 1-164-156-11 CERAMIC CHIP 0.1uF 25V J201 1-694-920-11 TERMINAL BOARD (S TERMINAL+1P)
C210 1-126-925-91 ELECT 470uF 20% 10V (VIDEO, S VIDEO (DVD ONLY))(MONITOR OUT)
C212 1-162-921-11 CERAMIC CHIP 33PF 5% 50V J202 1-817-601-11 JACK, PIN 3P (Y, CB/PB, CR/PR)
(COMPONENT VIDEO OUT)
C213 1-126-933-11 ELECT 100uF 20% 16V
C214 1-164-156-11 CERAMIC CHIP 0.1uF 25V < SHORT >
C216 1-162-960-11 CERAMIC CHIP 220PF 10% 50V JR362 1-216-864-11 SHORT CHIP 0
C218 1-104-662-91 ELECT 22uF 20% 25V JR364 1-216-864-11 SHORT CHIP 0
C219 1-104-662-91 ELECT 22uF 20% 25V < COIL >

C224 1-126-916-11 ELECT 1000uF 20% 6.3V L201 1-469-525-91 INDUCTOR 10uH
C227 1-126-933-11 ELECT 100uF 20% 16V
90
HCD-DX375
I/O JACK
< TRANSISTOR >
R378 1-216-841-11 METAL CHIP 47K 5% 1/10W
Q360 8-729-027-23 TRANSISTOR RT1P141C-TP-1 R384 1-216-841-11 METAL CHIP 47K 5% 1/10W
Q361 8-729-120-28 TRANSISTOR 2SC3052EF-T1-LEF R385 1-218-867-11 METAL CHIP 6.8K 5% 1/10W
Q362 8-729-120-28 TRANSISTOR 2SC3052EF-T1-LEF
R386 1-216-841-11 METAL CHIP 47K 5% 1/10W
< RESISTOR > *************************************************************
R204 1-216-821-11 METAL CHIP 1K 5% 1/10W A-1148-824-A JACK BOARD, COMPLETE

R207 1-216-864-11 SHORT CHIP 0 *********************
R209 1-216-864-11 SHORT CHIP 0
R215 1-218-867-11 METAL CHIP 6.8K 5% 1/10W < CAPACITOR >
R216 1-218-867-11 METAL CHIP 6.8K 5% 1/10W
C401 1-124-589-11 ELECT 47uF 20% 16V
R220 1-216-841-11 METAL CHIP 47K 5% 1/10W C405 1-164-156-11 CERAMIC CHIP 0.1uF 25V
R224 1-216-841-11 METAL CHIP 47K 5% 1/10W C410 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
R228 1-216-833-11 METAL CHIP 10K 5% 1/10W
R233 1-218-285-11 METAL CHIP 75 5% 1/10W
R234 1-216-809-11 METAL CHIP 100 5% 1/10W C431 1-117-863-11 CERAMIC CHIP 0.47uF 10% 6.3V
R253 1-216-845-11 METAL CHIP 100K 5% 1/10W C434 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V
R254 1-216-845-11 METAL CHIP 100K 5% 1/10W
R256 1-216-845-11 METAL CHIP 100K 5% 1/10W C471 1-124-222-91 ELECT 22uF 20% 6.3V
R330 1-218-867-11 METAL CHIP 6.8K 5% 1/10W
R331 1-218-867-11 METAL CHIP 6.8K 5% 1/10W C820 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
R334 1-218-867-11 METAL CHIP 6.8K 5% 1/10W
R338 1-218-867-11 METAL CHIP 6.8K 5% 1/10W < DIODE >
R339 1-218-867-11 METAL CHIP 6.8K 5% 1/10W
R343 1-216-829-11 METAL CHIP 4.7K 5% 1/10W D433 6-501-193-01 DIODE 1SS355WTE-17
D470 6-501-193-01 DIODE 1SS355WTE-17
R349 1-216-833-11 METAL CHIP 10K 5% 1/10W D493 6-501-193-01 DIODE 1SS355WTE-17
R350 1-216-833-11 METAL CHIP 10K 5% 1/10W D496 6-501-193-01 DIODE 1SS355WTE-17
R356 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R358 1-216-841-11 METAL CHIP 47K 5% 1/10W < FERRITE BEAD >
R359 1-216-817-11 METAL CHIP 470 5% 1/10W
R360 1-216-817-11 METAL CHIP 470 5% 1/10W FB410 1-469-144-21 FERRITE, EMI (SMD) (2012)
R363 1-216-829-11 METAL CHIP 4.7K 5% 1/10W FB420 1-469-144-21 FERRITE, EMI (SMD) (2012)
R364 1-216-829-11 METAL CHIP 4.7K 5% 1/10W FB450 1-216-864-11 SHORT CHIP 0
R365 1-216-841-11 METAL CHIP 47K 5% 1/10W FB460 1-216-864-11 SHORT CHIP 0
R366 1-216-841-11 METAL CHIP 47K 5% 1/10W
R367 1-216-821-11 METAL CHIP 1K 5% 1/10W FB461 1-469-144-21 FERRITE, EMI (SMD) (2012)
R374 1-216-841-11 METAL CHIP 47K 5% 1/10W
R376 1-216-864-11 SHORT CHIP 0 FB478 1-469-144-21 FERRITE, EMI (SMD) (2012)
R377 1-216-841-11 METAL CHIP 47K 5% 1/10W FB479 1-500-284-21 INDUCTOR, FERRITE BEAD
91
HCD-DX375
JACK LED
< IC > R463 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R464 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
IC401 8-759-100-96 IC NJM4558M-TE2 R470 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
IC402 8-759-100-96 IC NJM4558M-TE2 R471 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
< JACK > R472 1-216-819-11 METAL CHIP 680 5% 1/10W

R477 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
J401 1-819-878-11 JACK (AUDIO IN) R478 1-216-813-11 METAL CHIP 220 5% 1/10W
J402 1-819-878-11 JACK (PHONES) R479 1-216-864-11 SHORT CHIP 0
R480 1-216-804-11 METAL CHIP 39 5% 1/10W
< SHORT >
R481 1-216-845-11 METAL CHIP 100K 5% 1/10W
JR811 1-216-864-11 SHORT CHIP 0 R482 1-216-833-11 METAL CHIP 10K 5% 1/10W
JR812 1-216-864-11 SHORT CHIP 0 R487 1-216-864-11 SHORT CHIP 0
JR813 1-216-864-11 SHORT CHIP 0 R488 1-216-845-11 METAL CHIP 100K 5% 1/10W
JR814 1-216-864-11 SHORT CHIP 0 R492 1-216-864-11 SHORT CHIP 0
JR816 1-216-864-11 SHORT CHIP 0
R495 1-216-864-11 SHORT CHIP 0
JR817 1-216-864-11 SHORT CHIP 0
< SWITCH >
< TRANSISTOR >
S800 1-418-725-51 ENCODER, ROTARY (12 TYPE)
Q450 6-550-889-01 TRANSISTOR 2SC5938-T112-1B (– + VOLUME)
Q451 6-550-889-01 TRANSISTOR 2SC5938-T112-1B *************************************************************
Q460 6-550-889-01 TRANSISTOR 2SC5938-T112-1B
Q461 6-550-889-01 TRANSISTOR 2SC5938-T112-1B A-1148-823-A LED BOARD, COMPLETE
Q470 1-801-806-11 TRANSISTOR RT1N441C-TP-1 *******************
Q471 8-729-027-23 TRANSISTOR RT1P141C-TP-1 < CAPACITOR >

Q472 8-729-048-50 TRANSISTOR 2SK3018-T106
Q473 8-729-027-23 TRANSISTOR RT1P141C-TP-1 C849 1-164-360-11 CERAMIC CHIP 0.1uF 16V
Q474 8-729-027-24 TRANSISTOR RT1P140C-TP-1
Q475 1-801-806-11 TRANSISTOR RT1N441C-TP-1 < DIODE >
Q476 8-729-027-44 TRANSISTOR RT1N140C-TP-1 D811 8-719-056-13 DIODE SML79423C-TP15 (DISC 1)

D812 8-719-056-13 DIODE SML79423C-TP15 (DISC 2)
< RESISTOR > D813 8-719-056-13 DIODE SML79423C-TP15 (DISC 3)
D814 8-719-056-13 DIODE SML79423C-TP15 (DISC 4)
R401 1-218-707-11 METAL CHIP 4.3K 5% 1/10W D815 8-719-056-13 DIODE SML79423C-TP15 (DISC 5)
R402 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R410 1-216-845-11 METAL CHIP 100K 5% 1/10W < IC >
R411 1-216-817-11 METAL CHIP 470 5% 1/10W
R412 1-216-837-11 METAL CHIP 22K 5% 1/10W IC803 6-704-046-01 IC BU2099FV
R413 1-216-821-11 METAL CHIP 1K 5% 1/10W < TRANSISTOR >

R414 1-216-835-11 METAL CHIP 15K 5% 1/10W
R415 1-216-821-11 METAL CHIP 1K 5% 1/10W Q811 8-729-027-23 TRANSISTOR RT1P141C-TP-1
R421 1-216-817-11 METAL CHIP 470 5% 1/10W Q813 8-729-027-23 TRANSISTOR RT1P141C-TP-1
R423 1-216-821-11 METAL CHIP 1K 5% 1/10W
R431 1-216-864-11 SHORT CHIP 0 Q817 8-729-027-23 TRANSISTOR RT1P141C-TP-1
R433 1-216-827-11 METAL CHIP 3.3K 5% 1/10W Q820 8-729-027-23 TRANSISTOR RT1P141C-TP-1
R434 1-216-864-11 SHORT CHIP 0
R435 1-216-857-11 METAL CHIP 1M 5% 1/10W < RESISTOR >
R450 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R807 1-216-809-11 METAL CHIP 100 5% 1/10W
R460 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R830 1-216-837-11 METAL CHIP 22K 5% 1/10W
92
HCD-DX375
LED MAIN
C527 1-104-656-11 ELECT 2200uF 20% 6.3V
R835 1-216-817-11 METAL CHIP 470 5% 1/10W
R840 1-216-815-11 METAL CHIP 330 5% 1/10W
R854 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
< SWITCH > C3000 1-126-933-11 ELECT 100uF 20% 16V
S802 1-762-875-21 SWITCH, KEYBOARD (FUNCTION) C3001 1-126-947-11 ELECT 47uF 20% 16V
S803 1-762-875-21 SWITCH, KEYBOARD (.) C3002 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V
S804 1-762-875-21 SWITCH, KEYBOARD (X) C3011 1-126-947-11 ELECT 47uF 20% 16V
S805 1-762-875-21 SWITCH, KEYBOARD (x) C3012 1-164-156-11 CERAMIC CHIP 0.1uF 25V
S806 1-762-875-21 SWITCH, KEYBOARD (>) C3013 1-164-156-11 CERAMIC CHIP 0.1uF 25V
S807 1-762-875-21 SWITCH, KEYBOARD (A) C3014 1-164-156-11 CERAMIC CHIP 0.1uF 25V
S808 1-762-875-21 SWITCH, KEYBOARD (H) C3015 1-164-156-11 CERAMIC CHIP 0.1uF 25V
S809 1-762-875-21 SWITCH, KEYBOARD (DISC 5) C3016 1-164-156-11 CERAMIC CHIP 0.1uF 25V
************************************************************* C3021 1-126-947-11 ELECT 47uF 20% 16V
A-1148-794-A MAIN BOARD, COMPLETE C3023 1-164-156-11 CERAMIC CHIP 0.1uF 25V
*********************
< CAPACITOR > C3025 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C501 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C3027 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C3031 1-126-947-11 ELECT 47uF 20% 16V
C509 1-165-908-11 CERAMIC CHIP 1uF 10% 10V C3034 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C516 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C519 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C3052 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C522 1-127-715-91 CERAMIC CHIP 0.22uF 10% 16V C3054 1-126-933-11 ELECT 100uF 20% 16V
C3056 1-126-923-91 ELECT 220uF 20% 10V
C524 1-126-947-11 ELECT 47uF 20% 16V C3057 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
93
HCD-DX375
MAIN
C3058 1-162-910-11 CERAMIC CHIP 5PF 0.25PF 50V C3166 1-112-831-11 ELECT 2200uF 20% 35V
C3060 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V C3169 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C3068 1-162-927-11 CERAMIC CHIP 100PF 5% 50V C3170 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C3069 1-162-927-11 CERAMIC CHIP 100PF 5% 50V C3171 1-164-505-11 CERAMIC CHIP 2.2uF 16V
C3071 1-164-156-11 CERAMIC CHIP 0.1uF 25V C3200 1-104-329-11 CERAMIC CHIP 0.1uF 10% 50V
C3085 1-162-927-11 CERAMIC CHIP 100PF 5% 50V C3209 1-112-246-11 ELECT 100uF 20% 35V
C3212 1-112-246-11 ELECT 100uF 20% 35V
C3087 1-162-927-11 CERAMIC CHIP 100PF 5% 50V C3214 1-136-177-00 FILM 1uF 5% 50V
C3089 1-164-156-11 CERAMIC CHIP 0.1uF 25V C3215 1-136-177-00 FILM 1uF 5% 50V
C3090 1-104-658-91 ELECT 100uF 20% 10V C3216 1-112-831-11 ELECT 2200uF 20% 35V
C3112 1-112-246-11 ELECT 100uF 20% 35V
C3114 1-136-177-00 FILM 1uF 5% 50V C3259 1-112-246-11 ELECT 100uF 20% 35V
C3262 1-112-246-11 ELECT 100uF 20% 35V
C3115 1-136-177-00 FILM 1uF 5% 50V C3263 1-104-329-11 CERAMIC CHIP 0.1uF 10% 50V
C3116 1-112-831-11 ELECT 2200uF 20% 35V C3264 1-136-177-00 FILM 1uF 5% 50V
C3118 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V C3265 1-136-177-00 FILM 1uF 5% 50V
C3119 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V C3266 1-112-831-11 ELECT 2200uF 20% 35V
C3162 1-112-246-11 ELECT 100uF 20% 35V
C3164 1-136-177-00 FILM 1uF 5% 50V C3309 1-112-246-11 ELECT 100uF 20% 35V
C3312 1-112-246-11 ELECT 100uF 20% 35V
C3165 1-136-177-00 FILM 1uF 5% 50V C3313 1-104-329-11 CERAMIC CHIP 0.1uF 10% 50V
94
HCD-DX375
Ver. 1.1
MAIN
C3314 1-136-177-00 FILM 1uF 5% 50V CN601 1-784-374-21 CONNECTOR, FFC/FPC 15P
C3315 1-136-177-00 FILM 1uF 5% 50V CN701 1-779-277-11 CONNECTOR, FFC (LIF (NON-ZIF)) 9P
C3316 1-112-831-11 ELECT 2200uF 20% 35V CN3000 1-564-704-41 PIN, CONNECTOR (SMALL TYPE) 2P
C3317 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V CN3001 1-506-469-11 PIN, CONNECTOR 4P
C3319 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V CN3002 1-785-101-11 PIN, CONNECTOR (3.96mm PITCH) 3P
C3320 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V < DIODE >
C3322 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V D501 6-501-193-01 DIODE 1SS355WTE-17
D3071 6-501-193-01 DIODE 1SS355WTE-17
C3406 1-115-185-11 CERAMIC CHIP 0.033uF 10% 50V D3111 6-500-885-01 DIODE P6SMBJ33A-5
D3151 6-500-885-01 DIODE P6SMBJ33A-5
C3409 1-112-246-11 ELECT 100uF 20% 35V
C3412 1-112-246-11 ELECT 100uF 20% 35V D3201 6-500-885-01 DIODE P6SMBJ33A-5
C3414 1-136-177-00 FILM 1uF 5% 50V D3251 6-500-885-01 DIODE P6SMBJ33A-5
D3252 6-500-885-01 DIODE P6SMBJ33A-5
C3415 1-136-177-00 FILM 1uF 5% 50V D3301 6-500-885-01 DIODE P6SMBJ33A-5
C3416 1-112-831-11 ELECT 2200uF 20% 35V
D3501 6-500-885-01 DIODE P6SMBJ33A-5
C3421 1-117-370-11 CERAMIC CHIP 10uF 10V
< GROUND TERMINAL BOARD >
C3504 1-164-156-11 CERAMIC CHIP 0.1uF 25V EB501 1-537-770-21 TERMINAL BOARD, GROUND
C3505 1-107-725-11 CERAMIC CHIP 0.1uF 10% 16V EB505 1-537-770-21 TERMINAL BOARD, GROUND
EB703 1-537-770-21 TERMINAL BOARD, GROUND
C3509 1-112-246-11 ELECT 100uF 20% 35V EB3001 1-537-770-21 TERMINAL BOARD, GROUND
C3512 1-112-246-11 ELECT 100uF 20% 35V EB3002 1-537-770-21 TERMINAL BOARD, GROUND
C3514 1-136-177-00 FILM 1uF 5% 50V EB3004 1-537-770-21 TERMINAL BOARD, GROUND
C3515 1-136-177-00 FILM 1uF 5% 50V
C3516 1-112-831-11 ELECT 2200uF 20% 35V < FERRITE BEAD >
C3551 1-126-960-11 ELECT 1uF 20% 50V FB505 1-469-324-21 FERRITE, EMI (SMD) (2012)
C3552 1-126-964-11 ELECT 10uF 20% 50V
C3555 1-163-038-91 CERAMIC CHIP 0.1uF 25V FB506 1-469-324-21 FERRITE, EMI (SMD) (2012)
< CONNECTOR > FB508 1-469-324-21 FERRITE, EMI (SMD) (2012)
CN501 1-793-991-11 CONNECTOR, FFC/FPC 23P FB510 1-469-324-21 FERRITE, EMI (SMD) (2012)
CN502 1-506-469-11 PIN, CONNECTOR 4P
CN503 1-784-368-11 CONNECTOR, FFC/FPC 9P FB3051 1-216-295-91 SHORT CHIP 0
* CN506 1-564-714-11 PIN, CONNECTOR (SMALL TYPE) 12P
95
HCD-DX375
Ver. 1.1
MAIN
FL501 1-233-893-21 FILTER, CHIP EMI Q3101 8-729-600-22 TRANSISTOR 2SA1235TP-1EF
Q3152 8-729-600-22 TRANSISTOR 2SA1235TP-1EF
< IC >
IC501 6-806-094-01 IC M30622MEP-A61FPU0 Q3202 8-729-600-22 TRANSISTOR 2SA1235TP-1EF
IC502 6-702-302-01 IC TK11133CSCL-G Q3251 8-729-600-22 TRANSISTOR 2SA1235TP-1EF
IC503 6-708-922-01 IC PST3635NR Q3252 8-729-600-22 TRANSISTOR 2SA1235TP-1EF
IC504 6-709-034-01 IC NJM2887DL3 (TE2) Q3301 8-729-600-22 TRANSISTOR 2SA1235TP-1EF
IC621 6-707-095-01 IC BH2210FV-E2
IC622 6-707-095-01 IC BH2210FV-E2 Q3401 8-729-600-22 TRANSISTOR 2SA1235TP-1EF
IC3001 8-759-710-97 IC NJM4565M (TE2) Q3402 8-729-600-22 TRANSISTOR 2SA1235TP-1EF
IC3003 8-759-680-48 IC TC7WH157FK (TE85R) Q3551 8-729-120-28 TRANSISTOR 2SC3052EF-T1-LEF
IC3010 6-707-939-01 IC CXD9843AR
IC3020 6-707-939-01 IC CXD9843AR < RESISTOR >
IC3030 6-707-939-01 IC CXD9843AR R501 1-216-821-11 METAL CHIP 1K 5% 1/10W

IC3050 6-702-300-01 IC TK11118CSCL-G R502 1-216-833-11 METAL CHIP 10K 5% 1/10W
IC3051 8-759-649-50 IC SN74AHC1GU04DCKR R503 1-216-833-11 METAL CHIP 10K 5% 1/10W
IC3100 6-708-921-01 IC CXD9883M R504 1-216-841-11 METAL CHIP 47K 5% 1/10W

IC3250 6-708-921-01 IC CXD9883M R507 1-216-827-11 METAL CHIP 3.3K 5% 1/10W
IC3400 6-708-921-01 IC CXD9883M R509 1-216-809-11 METAL CHIP 100 5% 1/10W
< SHORT > R511 1-216-809-11 METAL CHIP 100 5% 1/10W

R512 1-216-833-11 METAL CHIP 10K 5% 1/10W
JC502 1-216-864-11 SHORT CHIP 0 R513 1-216-809-11 METAL CHIP 100 5% 1/10W
JC525 1-216-864-11 SHORT CHIP 0 R514 1-216-833-11 METAL CHIP 10K 5% 1/10W
R515 1-216-821-11 METAL CHIP 1K 5% 1/10W
< COIL >
R516 1-216-821-11 METAL CHIP 1K 5% 1/10W
L3052 1-414-754-11 INDUCTOR 10uH R519 1-216-833-11 METAL CHIP 10K 5% 1/10W
L3054 1-412-939-11 INDUCTOR 1uH
R521 1-216-809-11 METAL CHIP 100 5% 1/10W
L3201 1-456-680-11 INDUCTOR 10uH
R529 1-216-821-11 METAL CHIP 1K 5% 1/10W
L3302 1-456-680-11 INDUCTOR 10uH
R534 1-216-833-11 METAL CHIP 10K 5% 1/10W
L3402 1-456-680-11 INDUCTOR 10uH R536 1-216-864-11 SHORT CHIP 0
< TRANSISTOR > R541 1-216-833-11 METAL CHIP 10K 5% 1/10W

R543 1-216-833-11 METAL CHIP 10K 5% 1/10W
Q503 8-729-120-28 TRANSISTOR 2SC3052EF-T1-LEF R544 1-216-833-11 METAL CHIP 10K 5% 1/10W
Q504 6-550-718-01 TRANSISTOR RSR025N03TL R546 1-216-833-11 METAL CHIP 10K 5% 1/10W
Q3000 8-729-142-48 TRANSISTOR 2SD1616-TP-LK R549 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
Q3001 8-729-120-28 TRANSISTOR 2SC3052EF-T1-LEF
Q3002 8-729-120-28 TRANSISTOR 2SC3052EF-T1-LEF R550 1-216-821-11 METAL CHIP 1K 5% 1/10W
96
HCD-DX375
Ver. 1.1
MAIN
R554 1-216-833-11 METAL CHIP 10K 5% 1/10W
R3001 1-216-833-11 METAL CHIP 10K 5% 1/10W
R560 1-216-833-11 METAL CHIP 10K 5% 1/10W
R3011 1-216-817-11 METAL CHIP 470 5% 1/10W
R565 1-216-809-11 METAL CHIP 100 5% 1/10W
R3017 1-216-823-11 METAL CHIP 1.5K 5% 1/10W
R572 1-218-751-11 METAL CHIP 300K 5% 1/10W
R3026 1-216-823-11 METAL CHIP 1.5K 5% 1/10W
R578 1-216-809-11 METAL CHIP 100 5% 1/10W
R3035 1-216-809-11 METAL CHIP 100 5% 1/10W
R584 1-216-809-11 METAL CHIP 100 5% 1/10W R3037 1-216-823-11 METAL CHIP 1.5K 5% 1/10W
R586 1-216-809-11 METAL CHIP 100 5% 1/10W
R587 1-216-809-11 METAL CHIP 100 5% 1/10W R3052 1-216-857-11 METAL CHIP 1M 5% 1/10W
R3054 1-216-801-11 METAL CHIP 22 5% 1/10W
R604 1-216-809-11 METAL CHIP 100 5% 1/10W
R3061 1-216-864-11 SHORT CHIP 0
R609 1-216-809-11 METAL CHIP 100 5% 1/10W
R3066 1-216-809-11 METAL CHIP 100 5% 1/10W
R614 1-216-809-11 METAL CHIP 100 5% 1/10W
R3071 1-216-809-11 METAL CHIP 100 5% 1/10W
R629 1-216-813-11 METAL CHIP 220 5% 1/10W
R3077 1-216-809-11 METAL CHIP 100 5% 1/10W
R634 1-216-813-11 METAL CHIP 220 5% 1/10W
R3086 1-216-839-11 METAL CHIP 33K 5% 1/10W
R694 1-216-864-11 SHORT CHIP 0
97
HCD-DX375
Ver. 1.1
MAIN
R3091 1-216-837-11 METAL CHIP 22K 5% 1/10W
R3254 1-216-864-11 SHORT CHIP 0
R3096 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R3098 1-216-837-11 METAL CHIP 22K 5% 1/10W R3269 1-216-136-00 RES-CHIP 2.7 5% 1/8W
R3270 1-216-136-00 RES-CHIP 2.7 5% 1/8W
R3102 1-216-809-11 METAL CHIP 100 5% 1/10W
R3275 1-216-845-11 METAL CHIP 100K 5% 1/10W
R3116 1-216-797-11 METAL CHIP 10 5% 1/10W
R3119 1-216-136-00 RES-CHIP 2.7 5% 1/8W R3301 1-216-809-11 METAL CHIP 100 5% 1/10W
R3303 1-216-797-11 METAL CHIP 10 5% 1/10W
R3123 1-216-833-11 METAL CHIP 10K 5% 1/10W
R3319 1-216-136-00 RES-CHIP 2.7 5% 1/8W
R3151 1-216-809-11 METAL CHIP 100 5% 1/10W
R3324 1-216-833-11 METAL CHIP 10K 5% 1/10W
R3165 1-216-797-11 METAL CHIP 10 5% 1/10W
R3402 1-216-809-11 METAL CHIP 100 5% 1/10W
R3172 1-216-833-11 METAL CHIP 10K 5% 1/10W
R3416 1-216-797-11 METAL CHIP 10 5% 1/10W
R3177 1-216-845-11 METAL CHIP 100K 5% 1/10W
R3423 1-216-833-11 METAL CHIP 10K 5% 1/10W
R3207 1-216-835-11 METAL CHIP 15K 5% 1/10W
R3501 1-216-809-11 METAL CHIP 100 5% 1/10W
R3221 1-216-833-11 METAL CHIP 10K 5% 1/10W
R3515 1-216-797-11 METAL CHIP 10 5% 1/10W
R3226 1-216-845-11 METAL CHIP 100K 5% 1/10W
98
HCD-DX375
MAIN MOTOR POWER
R3551 1-216-845-11 METAL CHIP 100K 5% 1/10W
R3553 1-216-833-11 METAL CHIP 10K 5% 1/10W C937 1-100-756-91 CERAMIC CHIP 0.047uF 50V
R3554 1-216-845-11 METAL CHIP 100K 5% 1/10W 0 C938 1-113-898-11 CERAMIC 330PF 10% 250V
R3555 1-216-864-11 SHORT CHIP 0 C939 1-136-165-00 FILM 0.1uF 5% 50V
C940 1-128-947-31 ELECT 3300uF 20% 10V
< NETWORK RESISTOR > C942 1-126-941-11 ELECT 470uF 20% 25V
C943 1-126-933-11 ELECT 100uF 20% 16V
RB621 1-233-576-11 RES, CHIP NETWORK 100 (3216) C944 1-128-951-21 ELECT 2200uF 20% 16V
RB624 1-233-411-11 RES, CHIP NETWORK 220 (3216)
C948 1-126-925-91 ELECT 470uF 20% 10V
RB627 1-236-908-11 RES, CHIP NETWORK 10K (3216) C951 1-100-566-91 CERAMIC CHIP 0.1uF 10% 25V
RB628 1-236-908-11 RES, CHIP NETWORK 10K (3216) C952 1-100-756-91 CERAMIC CHIP 0.047uF 50V
RB629 1-236-908-11 RES, CHIP NETWORK 10K (3216)
RB630 1-236-908-11 RES, CHIP NETWORK 10K (3216) C953 1-117-214-11 CERAMIC 0.001uF 10% 2KV
< VIBRATOR > C955 1-100-566-91 CERAMIC CHIP 0.1uF 10% 25V
X501 1-795-058-21 VIBRATOR, CERAMIC 5MHz C960 1-100-566-91 CERAMIC CHIP 0.1uF 10% 25V
X3051 1-795-660-21 QUARTZ CRYSTAL UNIT 49.152MHz
************************************************************* 0 C963 1-113-907-51 CERAMIC 0.0022uF 99% 250V
0 C964 1-113-907-51 CERAMIC 0.0022uF 99% 250V
MOTOR BOARD C967 1-100-566-91 CERAMIC CHIP 0.1uF 10% 25V
************ C968 1-100-566-91 CERAMIC CHIP 0.1uF 10% 25V
< SWITCH >
S761 1-786-704-11 SWITCH, LEVER (SUB TRAY OUT) C971 1-100-566-91 CERAMIC CHIP 0.1uF 10% 25V
************************************************************* C976 1-126-933-11 ELECT 100uF 20% 16V
A-1146-005-A POWER BOARD, COMPLETE < CONNECTOR >

***********************
CN901 1-564-321-00 PIN, CONNECTOR (3.96mm PITCH) 2P
< CAPACITOR >
< DIODE >
0 C901 1-165-529-11 MYLAR 0.22uF 10 275V
0 C902 1-165-529-11 MYLAR 0.22uF 10 275V 0 D901 8-719-082-57 DIODE D5SBA60F01
0 C903 1-112-330-11 ELECT (BLOCK) 1000uF 20% 200V 0 D905 8-719-063-74 DIODE D1NL20U-TR2
0 C905 1-112-334-91 FILM 0.01uF 5% 400V 0 D906 6-501-193-01 DIODE 1SS355WTE-17
0 C906 1-117-828-11 CAP, METALIZED PP FILM 3300PF 0 D907 6-501-193-01 DIODE 1SS355WTE-17
0 D908 6-501-193-01 DIODE 1SS355WTE-17
0 C907 1-162-965-11 CERAMIC CHIP 0.0015uF 10% 50V
0 C908 1-107-909-11 ELECT 47uF 20% 35V 0 D909 6-501-193-01 DIODE 1SS355WTE-17
0 C909 1-162-960-11 CERAMIC CHIP 220PF 10% 50V 0 D910 6-501-193-01 DIODE 1SS355WTE-17
0 C910 1-107-906-11 ELECT 10uF 20% 50V 0 D913 6-500-241-01 DIODE SARS03
0 C911 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V 0 D914 6-501-193-01 DIODE 1SS355WTE-17
0 D915 8-719-977-28 DIODE UDZSTE-1710B
0 C913 1-117-693-11 CERAMIC 100PF 10% 250V
0 C918 1-113-925-11 CERAMIC 0.01uF 20% 250V 0 D921 6-501-424-01 DIODE STO2D-140
0 C920 1-113-925-11 CERAMIC 0.01uF 20% 250V 0 D922 8-719-063-74 DIODE D1NL20U-TR2
0 C922 1-128-560-11 ELECT 22uF 20% 100V 0 D923 8-719-977-28 DIODE UDZSTE-1710B
0 C923 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V 0 D924 8-719-083-69 DIODE UDZSTE-1724B
0 D925 8-719-069-54 DIODE UDZSTE-175.1B
0 C924 1-126-961-11 ELECT 2.2uF 20% 50V
0 C925 1-107-974-81 CERAMIC 47PF 5% 2KV 0 D926 8-719-977-28 DIODE UDZSTE-1710B
0 C928 1-113-896-11 CERAMIC 220PF 10% 250V D931 6-501-413-01 DIODE FCU20UC20
0 C929 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V D932 8-719-069-54 DIODE UDZSTE-175.1B
0 C930 1-117-693-11 CERAMIC 100PF 10% 250V D941 6-500-288-11 DIODE EK19LF-F7
D942 8-719-080-53 DIODE RK36LF-B3
C932 1-100-924-21 ELECT 2200uF 20% 35V
C933 1-100-924-21 ELECT 2200uF 20% 35V D943 8-719-080-53 DIODE RK36LF-B3
C934 1-112-831-11 ELECT 2200uF 20% 35V D944 6-500-288-11 DIODE EK19LF-F7
C935 1-165-319-11 CERAMIC CHIP 0.1uF 50V D945 8-719-083-67 DIODE UDZSTE-1720B
99
HCD-DX375
POWER
< GROUND TERMINAL BOARD > 0 R910 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
0 R911 1-216-813-11 METAL CHIP 220 5% 1/10W
EB902 1-537-770-21 TERMINAL BOARD, GROUND 0 R912 1-216-361-61 METAL OXIDE 0.22 5% 2W
EB903 1-537-770-21 TERMINAL BOARD, GROUND 0 R913 1-216-361-61 METAL OXIDE 0.22 5% 2W
EB904 1-537-770-21 TERMINAL BOARD, GROUND 0 R914 1-243-669-11 METAL 0.05 5% 5W
0 R919 1-216-836-11 METAL CHIP 18K 5% 1/10W
< FUSE HOLDER > 0 R922 1-216-793-11 METAL CHIP 4.7 5% 1/10W
0 FH901 1-533-313-11 FUSE HOLDER 0A 0V 0 R923 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
0 FH902 1-533-313-11 FUSE HOLDER 0A 0V 0 R925 1-216-797-11 METAL CHIP 10 5% 1/10W
0 R926 1-216-855-11 METAL CHIP 680K 5% 1/10W
< FUSIBLE > 0 R927 1-216-348-00 METAL OXIDE 0.82 5% 1W
0 R929 1-249-478-11 CARBON 2.2 5% 1/2W
0 FR901 1-220-886-11 FUSIBLE 0.1 10% 1W
0 FR902 1-220-886-11 FUSIBLE 0.1 10% 1W R931 1-218-859-11 METAL CHIP 3.3K 0.5% 1/10W
R932 1-218-883-11 METAL CHIP 33K 0.5% 1/10W
< IC > R933 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R934 1-216-821-11 METAL CHIP 1K 5% 1/10W
0 IC901 6-707-741-01 IC STR-F6138-LF1352 R935 1-216-821-11 METAL CHIP 1K 5% 1/10W
0 IC921 6-707-740-01 IC STR-V153
IC931 8-759-648-34 IC TA76431AS (TPE6) R936 1-216-853-11 METAL CHIP 470K 5% 1/10W
IC941 6-707-746-01 IC SI-3120KM-TL R937 1-216-833-11 METAL CHIP 10K 5% 1/10W
R939 1-218-859-11 METAL CHIP 3.3K 0.5% 1/10W
IC951 6-707-743-01 IC TA76L431S (TPE6, Q)
R941 1-216-864-11 SHORT CHIP 0
< COIL > R943 1-216-864-11 SHORT CHIP 0
R946 1-216-811-11 METAL CHIP 150 5% 1/10W
L942 1-414-398-11 INDUCTOR 10uH
L945 1-414-398-11 INDUCTOR 10uH R951 1-218-831-11 METAL CHIP 220 0.5% 1/10W
L947 1-414-398-11 INDUCTOR 10uH R952 1-218-855-11 METAL CHIP 2.2K 0.5% 1/10W
R953 1-218-861-11 METAL CHIP 3.9K 0.5% 1/10W
< LINE FILTER > R956 1-216-821-11 METAL CHIP 1K 5% 1/10W

R957 1-216-841-11 METAL CHIP 47K 5% 1/10W
0 LF901 1-457-054-21 COIL, LINE FILTER R958 1-216-821-11 METAL CHIP 1K 5% 1/10W
0 LF902 1-457-054-21 COIL, LINE FILTER R965 1-218-865-11 METAL CHIP 5.6K 0.5% 1/10W
R966 1-216-821-11 METAL CHIP 1K 5% 1/10W
< IC >
R967 1-216-821-11 METAL CHIP 1K 5% 1/10W
0 PC901 6-600-438-01 IC TLP421F (D4-GR) 0 R968 1-216-821-11 METAL CHIP 1K 5% 1/10W
0 PC902 6-600-438-01 IC TLP421F (D4-GR) R969 1-216-821-11 METAL CHIP 1K 5% 1/10W
0 PC903 6-600-438-01 IC TLP421F (D4-GR) R971 1-216-864-11 SHORT CHIP 0
R974 1-216-827-11 METAL CHIP 3.3K 5% 1/10W
< TRANSISTOR >
< TRANSFORMER >
0 Q901 8-729-140-04 TRANSISTOR 2SB1116A-TP-LK
0 Q921 8-729-142-51 TRANSISTOR 2SD1616A-TP-LK 0 T901 1-443-649-11 TRANSFORMER, CONVERTER
Q943 1-801-806-11 TRANSISTOR RT1N441C-TP-1 0 T902 1-443-650-11 TRANSFORMER, CONVERTER
Q945 6-550-718-01 TRANSISTOR RSR025N03TL
Q947 1-801-806-11 TRANSISTOR RT1N441C-TP-1 < THERMISTOR >
< RESISTOR > 0 TH901 1-805-841-21 THERMISTOR, NTC 3.0
0 R902 1-219-769-11 METAL 3.3M 5% 1/2W < VARISTOR >

0 R903 1-215-926-00 METAL OXIDE 33K 5% 3W
0 R904 1-215-926-00 METAL OXIDE 33K 5% 3W 0 VDR901 1-805-482-11 VARISTOR
0 R905 1-216-797-11 METAL CHIP 10 5% 1/10W *************************************************************
0 R906 1-216-827-11 METAL CHIP 3.3K 5% 1/10W
0 R907 1-216-833-11 METAL CHIP 10K 5% 1/10W

0 R908 1-260-105-11 CARBON 3.3K 5% 1/2W
0 R909 1-216-845-11 METAL CHIP 100K 5% 1/10W
100
HCD-DX375
RELAY SENSOR SPEAKER SW SW (1) SW (2)
A-4750-232-A RELAY BOARD, COMPLETE C313 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
********************** C314 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
< CAPACITOR >
C761 1-162-306-11 CERAMIC 0.01uF 30% 16V C319 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
C762 1-162-306-11 CERAMIC 0.01uF 30% 16V C320 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
< CONNECTOR > C321 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
CN701 1-779-558-11 CONNECTOR, FFC (LIF (NON-ZIF)) 21P C323 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
< DIODE >
< CONNECTOR >
D701 8-719-921-40 DIODE MTZJ-T-77-4.7B
D711 8-719-982-10 DIODE MTZJ-T-77-4.3A CN301 1-564-507-11 PLUG, CONNECTOR 4P
CN302 1-564-320-00 PIN, CONNECTOR (3.96mm PITCH) 2P
< IC > CN303 1-564-509-11 PLUG, CONNECTOR 6P
IC701 8-759-598-69 IC BA6956AN < EARTH TERMINAL >

IC711 8-759-598-69 IC BA6956AN
EP301 1-537-770-21 TERMINAL BOARD, GROUND
< TRANSISTOR > EP302 1-537-770-21 TERMINAL BOARD, GROUND
Q751 8-729-119-78 TRANSISTOR 2SC1740S-QRT < TERMINAL >
< RESISTOR > TB301 1-780-344-11 TERMINAL BOARD (SPEAKER) 4P

(FRONT R, FRONT L, CENTER, WOOFER)
R701 1-249-415-11 CARBON 680 5% 1/4W TB302 1-780-343-11 TERMINAL BOARD (SPEAKER) 2P
R702 1-247-807-31 CARBON 100 5% 1/4W (SUR R, SUR L)
R711 1-249-415-11 CARBON 680 5% 1/4W *************************************************************
R712 1-247-807-31 CARBON 100 5% 1/4W
R751 1-247-806-11 CARBON 91 5% 1/4W SW BOARD
********
R752 1-249-429-11 CARBON 10K 5% 1/4W
R753 1-249-429-11 CARBON 10K 5% 1/4W < SWITCH >
R754 1-249-430-11 CARBON 12K 5% 1/4W
R755 1-249-429-11 CARBON 10K 5% 1/4W S801 1-762-875-21 SWITCH, KEYBOARD (?/1)
************************************************************* *************************************************************
SENSOR BOARD SW (1) BOARD

************* ************
< IC > < SWITCH >
IC751 8-759-989-76 IC RPR-359F S721 1-786-084-11 SWITCH, DETECTION (MAIN TRAY IN/OUT)
************************************************************* *************************************************************
SPEAKER BOARD SW (2) BOARD

************** ************
< CAPACITOR > < SWITCH >
C301 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V S731 1-786-382-11 SWITCH, PUSH (1 KEY) (SUB TRAY IN)
C302 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V *************************************************************
C304 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V MISCELLANEOUS
C305 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V **************
C306 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V 4 1-828-953-11 WIRE (FLAT TYPE) (9 CORE)
C307 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V 5 1-693-703-11 TUNER (FM/AM) (TM10SU)
C308 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V 10 1-787-331-11 FAN, D.C.
101
HCD-DX375
Ref. No. Part No. Description Remark

0 109 1-830-190-11 CORD, POWER

0 302 8-820-291-02 OPTICAL PICK-UP (KHM-310CAB/C2RP)
0 F901 1-532-749-11 FUSE, GLASS TUBE (8A/125V)
M761 A-4713-174-A MOTOR (81) ASSY (LD/ST MOTOR)
M762 A-4713-174-A MOTOR (81) ASSY (BU U/D MOTOR)

S771 1-478-552-11 ENCODER, ROTARY (MD)
S781 1-478-551-11 ENCODER, ROTARY (ST U/D ENCORDER)
102
HCD-DX375
MEMO
103
HCD-DX375
REVISION HISTORY
Clicking the version allows you to jump to the revised page.

Also, clicking the version at the upper right on the revised page allows you to jump to the next revised
page.
Ver. Date Description of Revision

1.0 2006.03 New
1.1 2006.04 Correction of Test mode (ENG-06003)
“DIODE P6SMB39AT3” is changed to “DIODE P6SMBJ33A-5”. (ECN-ECB47846)
Change of the parts R3107, R3157, R3207, R3257, R3307, R3407

and R3507 (ECN-ECB55469)
Change of the parts IC102 of the DMB12 board (ECN-ECB53938)
Change of the parts R3017, R3026 and R3037 (ECN-ECB54487)

Service Manual: HCD-DX375

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Service Manual: HCD-DX375

Uploaded by

Copyright:

Available Formats

HCD-DX375

SERVICE MANUAL US Model

Ver. 1.1 2006.04

HCD-DX375 is the amplifier, DVD/CD and tuner

AUDIO POWER SPECIFICATIONS Inputs AM tuner section

SUPER AUDIO CD/DVD RECEIVER

Downloaded from www.Manualslib.com manuals search engine

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE

NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK Self-diagnosis Function

NOTES ON LASER DIODE EMISSION CHECK C:13:50

The laser beam on this model is concentrated so as to be focused on

Note on DMB12 board replacement

tweezers 1 Insert tip of tweezers through the hole

2 Attach an adhesive tape on the DVD LID and draw it out.

Discharge the charged electricity in capacitors to prevent electric shock as follows

*Connect the specified resistor

Fix the capacitors with adhesive agent as follows

Precaution when replacing the CAP

screws (+BVTP 2.6)

CAP (FUNK) button (disk),

CAP (PLAY) JACK board screw (+BVTP 2.6)

PRECAUTION WHEN INSTALLING A NEW OP UNIT /

Precaution on the connector processing of the POWER board.

IC941 IC942 IC943

When re-assembling, leave 30 mm between

• DMB12 board service position

Remove the DMB12 board once.

• POWER board service position

Remove the DMB12 board and

Front panel assy Connect the flexible cable and

• MAIN board service position

DMB12 board, bracket (HDMI) Remove the three connectors of

Remove the DMB12 board ,

Front panel assy Connect the flexible cable and

A "/1 (on/standby) (30) G PHONES jack (30)

SPEAKER COMPONENT VIDEO OUT TV

Y P B/C B P R/C R COAXIAL

A HDMI OUT jack (24) E COAXIAL FM 75Ω jack (13)

Front panel display

A–O P–Z [/1 (on/standby) 1 (19, 22, 30,

3-1. DISASSEMBLY FLOW

3-2.CASE, FRONT PANEL ASSY

3-3.FL BOARD, SW BOARD 3-5.DMB12 BOARD

3-4.JACK BOARD, LED BOARD

3-10.DVD MECHANISM DECK

3-13.BASE UNIT (DVBU101) 3-12.MOTOR BOARD

3-14.OPTICAL PICK-UP 3-16.LEVER ASSY

3-15.GEAR (SUB TRAY 1), 3-17.STOCKER SECTION 3-20.ROTARY ENCODER (MD)

3-18.CAM (STOCKER) 3-21.GEAR (BU1)

Note: Follow the disassembly procedure in the numerical order given.

9 wire (flat type)

3 loading panel qf claw

qs four screws (+BV3)

When re-assembling, leave 30 mm

DVD lid clamp

2 Attach an adhesive tape on the DVD LID and draw it out.

3-3. FL BOARD, SW BOARD

9 wire (flat type)

4 four screws (+BVTP 2.6)

5 shield plate (FC) 2 six claws

3-4. JACK BOARD, LED BOARD

5 eight screws (+BVTP 2.6)