Respironics V60/V60 Plus Ventilator: User Manual
Respironics V60/V60 Plus Ventilator: User Manual
User Manual
Table of contents
2. Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
iii
Leak adaptation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Auto-Trak+ (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
High flow therapy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Ventilation modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
CPAP mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
PCV mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
S/T mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
AVAPS mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11
PPV mode (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13
Oxygen mixing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15
6. Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Changing the mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
Changing control settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
Making batch setting changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
Changing individual ventilator settings . . . . . . . . . . . . . . . . . . . . . . 6-4
Using the Ramp Time function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5
Using the 100% O2 function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6
Using PPV. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
About Max V and Max P alarms and alarm limits . . . . . . . . . . . . . . . 6-7
Guidelines for using PPV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
Changing alarm settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12
Selecting the mask and exhalation port . . . . . . . . . . . . . . . . . . . . . . . . 6-12
Running the exhalation port test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-16
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-16
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-17
Other functions: the Menu window . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-17
Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-17
Loudness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-17
Mask/Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-18
Vent Info (ventilator information) . . . . . . . . . . . . . . . . . . . . . . . . . 6-18
iv
Screen Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-18
Auto-Trak+ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-18
Standby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-20
Help function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-22
Table of modes and control settings. . . . . . . . . . . . . . . . . . . . . . . . . . 6-23
v
Service and repairs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-9
Repacking and shipping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-9
vi
D. Regulatory compliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-1
Electromagnetic compatibility (EMC) . . . . . . . . . . . . . . . . . . . . . . . . . . D-1
Electromagnetic compatibility declaration . . . . . . . . . . . . . . . . . . . . . . D-1
Electromagnetic emissions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-2
Electromagnetic immunity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-3
RF immunity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-6
RFID reader separation distance . . . . . . . . . . . . . . . . . . . . . . . . . . D-6
Cables That May Affect IEC 60601-1-2 Compliance . . . . . . . . . . . . . . . D-7
WEEE recycling directive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-7
Classification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-8
Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-8
Applied parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-9
Accessible parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-9
Detachable components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-9
Essential performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-9
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Glossary-1
Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Index-1
vii
viii
Chapter 1. Warnings, cautions, and notes
Definitions WARNING: Alerts the user to the possibility of injury, death, or other serious adverse
reactions associated with the use or misuse of the device.
CAUTION: Alerts the user to the possibility of a problem with the device
associated with its use or misuse, such as device malfunction, device
failure, damage to the device, or damage to other property.
1-1
Warnings, cautions, and notes
WARNING: We do not recommend you use AVAPS on patients who require rapid and
frequent IPAP adjustments to maintain a consistent tidal volume. AVAPS, a
volume targeted mode, changes the IPAP setting in order to achieve the
target tidal volume. During AVAPS setup, there may be a period of time
before the target tidal volume is achieved. AVAPS is ideal for more
stabilized patients.
WARNING: To reduce the risk of CO2 rebreathing, make sure EPAP pressures and
exhalation times are sufficient to clear all exhaled gas through the
exhalation port. In noninvasive ventilation continuous air flow through the
port flushes exhaled gases from the circuit. The ability to completely
exhaust exhaled gas from the circuit depends on the EPAP setting and I:E
ratio. Higher tidal volumes further increase the volume of CO2 rebreathed
by the patient. Note: this may occur if exhalation time is insufficient.
WARNING: To reduce the risk of CO2 rebreathing, monitor the patient for changes in
respiratory status at the start of ventilation and with each change in
ventilator settings, circuit configuration, or patient condition. Pay
attention to ventilator alarms that warn of increased CO2 rebreathing risk.
WARNING: To ensure accuracy of oxygen administration and to monitor for the
presence of contamination (incorrect gas connected), use an external
oxygen monitor to verify the oxygen concentration in the delivered gas.
WARNING: To reduce the risk of fire, use the ventilator in well-ventilated areas away
from flammable anesthetics. Do not use in a hyperbaric chamber or other
similarly oxygen-enriched environments. Do not use near an open flame.
WARNING: To reduce the risk of electric shock from liquid entering the device, do
not put a container filled with a liquid on the ventilator.
WARNING: To reduce patient risk of oxygen toxicity, keep free-flowing oxygen away
from air inlet of ventilator.
WARNING: The nurse call/remote alarm should be considered a backup to the
ventilator’s primary alarm system.
WARNING: Set the alarm loudness above the ambient level. Setting the alarm
loudness too low may prevent recognition of alarm conditions.
WARNING: Avoid blocking the alarm speakers beneath the ventilator.
WARNING: Do not leave the ventilator unattended when stationed on an incline.
WARNING: The V60/V60 Plus Ventilator may cause radio interference or may disrupt
the operation of nearby equipment. It may be necessary to take mitigation
measures, such as re-orienting or relocating the ventilator or shielding
the location.
WARNING: This Equipment is designed to comply with IEC 60601-1-2. This
equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with instructions, may cause
harmful interference to other devices in the vicinity. However, there is no
guarantee that interference will not occur in a particular installation.
Harmful interference to other devices can be determined by turning this
equipment ON and OFF. Try to correct the interference using one or more
of the following:
- Reorient or relocate the receiving device
- Increase the separation between the equipment
1-2
Warnings, cautions, and notes
1-3
Warnings, cautions, and notes
NOTE: All ventilator mode and alarm settings, alarm messages and
significant events are retained and automatically logged, even when
power is lost.
NOTE: Any serious incident that has occurred in relation to this device
should be reported to Philips and the competent authority of the
country in which the user and/or patient is established.
Preparing for WARNING: Connect the ventilator only to an appropriate medical-grade oxygen
source.
ventilation
WARNING: To reduce the risk of hypoxia, connect only oxygen to the high-pressure
connector at the rear of the ventilator.
WARNING: The ventilator is a high-flow device. Connect it only to a gas supply
system that can provide adequate flow to all terminal outlets. Connecting
the ventilator to an adequate gas supply system helps ensure that the
ventilator and other connected devices perform to their specifications.
WARNING: To reduce the risk of fire, do not use a high-pressure oxygen hose that is
worn or contaminated with combustible materials like grease or oil.
WARNING: The Respironics V60/V60 Plus Ventilator is designed to use ambient air
and high pressure 100% oxygen. No other gases should be used.
WARNING: Do not use the ventilator with helium or helium mixtures. The ventilator is
not intended to be used with helium or heliox. Connecting helium to the
ventilator may affect ventilator performance, gas mixtures, and
measurements due to the lower density of helium.
WARNING: Do not use the ventilator with nitric oxide.
WARNING: To prevent possible asphyxia and to reduce the risk of CO2 rebreathing,
take these precautions with respect to mask and exhalation port use:
- Use only an oro-nasal mask with an anti-asphyxia valve or a nasal
mask for noninvasive ventilation.
- Do not occlude the exhalation port.
- Turn on the ventilator and verify that the port is operational before
application. Pressurized gas from the ventilator should cause a
continuous flow of air to exhaust from the leak port, flushing exhaled
gas from the circuit.
- Never leave the mask on the patient while the ventilator is not
operating. When the ventilator is not operating, the exhalation port
does not allow sufficient exhaust to eliminate CO2 from the circuit.
Substantial CO2 rebreathing may occur.
WARNING: The patient’s exhaled volume can differ from the measured exhaled
volume due to leaks around the mask during noninvasive ventilation.
WARNING: To ensure normal air circulation and exchange, do not cover or block the
ports on the ventilator. Do not block the air inlet panel on the right side of
the ventilator.
1-4
Warnings, cautions, and notes
1-5
Warnings, cautions, and notes
WARNING: To reduce the risk of strangulation from patient tubing, use a tubing
support arm and secure the proximal pressure line with clips.
WARNING: To reduce the risk of electric shock, connect the ventilator to an AC
supply mains with protective earth only.
WARNING: Do not use extension cords, adapters, or power cords with the ventilator
that are not approved by Respironics.
WARNING: To prevent unintentional disconnection of the power cord, always use the
correct, Philips-supplied power cord and lock it into place with the power
cord retainer before you switch the ventilator on. The retainer is designed
to hold the connector end of the Philips-supplied cord securely in place.
WARNING: The V60/V60 Plus Ventilator should not be positioned in a way that makes
it difficult to disconnect from mains power if necessary. Disconnect from
supply mains by removing the power cord from the wall outlet. The AC
mains plug is used as disconnection device.
WARNING: To reduce the risk of electric shock, regularly inspect the AC power cord
and verify that it is not frayed or cracked.
WARNING: To reduce the risk of strangulation, route the power cord to avoid
entanglement.
WARNING: To reduce the risk of power failure to the ventilator, pay close attention to
the battery’s charge level. The battery’s operation time is approximate and
is affected by ventilator settings, discharge and recharge cycles, battery
age, and ambient temperature.
WARNING: Always check the status of the oxygen cylinders before using the
ventilator during transport.
WARNING: Provide external oxygen monitoring to minimize patient risk in case of O2
supply loss or ventilator failure.
WARNING: To ensure the ventilator’s safe operation, always verify ventilator
operation as described in “Verify ventilator operation” on page 5-8 before
using the ventilator on a patient. If the ventilator fails any tests, remove it
from clinical use immediately. Do not use the ventilator until necessary
repairs are completed and all tests have passed.
WARNING: To prevent possible patient injury due to nonannunciating alarms, verify
the operation of any remote alarm device before use.
WARNING: To prevent possible patient injury, always return alarm settings to
hospital-standard values after verifying ventilator operation.
WARNING: Manufacturer default settings are not appropriate for all patients. Prior to
using the ventilator, verify that the current alarm settings or defaults are
appropriate for each particular patient.
CAUTION: To prevent possible damage to the ventilator, ensure that the
connection to the oxygen supply is clean and unlubricated, and that
there is no water in the oxygen supply gas.
CAUTION: For 120 V equipment, grounding reliability can only be achieved
when it is connected to an equivalent receptacle marked “hospital
only” or “hospital grade.”
1-6
Warnings, cautions, and notes
Operation WARNING: To prevent possible patient injury, avoid setting alarm limits to extreme
values, which can render the alarm system useless.
WARNING: PPV limits are not intended to be the primary ventilator alarms and should
not be substituted for the alarms found in the Alarm Settings window.
WARNING: To prevent the delivery of excessive pressure or volume, set the PPV
limits appropriately. Delivery of excessive pressure or volume can occur
from a sudden increase in mask leak, inappropriate settings, or a plugged
or kinked proximal pressure line. Conversely, insufficient treatment may
result if limits are set too low.
WARNING: Nebulization or humidification can increase the resistance of breathing
system filters. When using a nebulizer or humidifier, monitor the
breathing system filter frequently for increased resistance and blockage.
WARNING: Using a jet nebulizer can cause inadvertent alarms and affect the
accuracy of delivered FiO2. To reduce patient risk, use only an approved
nebulizer.
Operation in high flow WARNING: When transitioning from a high flow therapy interface to an NIV mask,
ensure that an exhalation port is placed in the circuit and is unobstructed
therapy (HFT) to reduce the risk of CO2 rebreathing.
WARNING: When transitioning from ventilation to high flow therapy, remove the NIV
mask and use only a Philips-approved high flow patient interface to
minimize pressure build-up and patient discomfort.
WARNING: When transitioning from high flow therapy to ventilation, remove the high
flow nasal cannula as it is restrictive and may defeat alarms such as
patient disconnect. Using a high flow nasal cannula in an NIV mode may
lead to hypercarbia due to the inability to provide pressure support.
WARNING: Patient alarms are not available during high flow therapy (HFT) as the
therapy uses an open system. A high flow nasal cannula occupies only a
portion of the nares and patients can breathe through their mouth, which
prevents estimation of patient parameters such as tidal volume,
respiratory rate, pressure, and minute ventilation. Provide external
monitoring, including oximetry, to inform the clinician of a change in the
patient's condition.
1-7
Warnings, cautions, and notes
WARNING: During high flow therapy (HFT), verify that an occlusive patient interface
is not being used. Occlusive patient interfaces include a cannula fully
sealed within the nares, an NIV mask, or a direct connection to a
tracheostomy tube or endotracheal tube. Remove any occlusive interface
immediately as this may expose the patient to unintended high pressures.
Alarms and messages WARNING: If AC power fails and the backup battery is not installed or is depleted, an
audible and visual alarm annunciates for at least 2 minutes. Immediately
discontinue ventilator use and secure an alternative means of ventilation.
As in most ventilators with passive exhalation ports, when power is lost,
sufficient air is not provided through the circuit and exhaled air may be
rebreathed.
Care and WARNING: To reduce the risk of electric shock, power down the ventilator and
disconnect it from AC power before cleaning, disinfecting, or servicing it.
maintenance
WARNING: Turn off the ventilator and disconnect it from the AC mains outlet before
you perform decontamination or maintenance procedures. Failure to do so
may result in electric shock.
WARNING: To prevent patient or ventilator contamination, inspect and replace the
main flow bacteria filter between patients and at regular intervals (or as
stated by the manufacturer).
WARNING: To prevent possible patient injury, inspect and verify the proper operation
of the exhalation port regularly during use.
WARNING: To reduce the risk of fire, explosion, leakage, or other hazard, take these
precautions with respect to the battery:
- Do not attempt to disassemble, open, drop, crush, bend or deform,
insert foreign objects into, puncture, or shred the battery pack; modify
or remanufacture it; immerse or expose it to water or other liquids;
expose it to fire, excessive heat (including soldering irons); or put it in
a microwave oven.
- Replace the battery only with another battery specified by the
manufacturer.
- Follow all instructions for proper use of the battery.
- Do not short-circuit the battery or allow metallic or conductive objects
to contact the battery connector housing.
- Use the battery with the Respironics V60/V60 Plus Ventilator only.
WARNING: Modification of the V60/V60 Plus Ventilator and associated equipment is
not permitted and may compromise ventilator operation and patient
safety. Service should only be performed by qualified service personnel.
WARNING: Only authorized service personnel should replace parts within the
ventilator or perform other service activities. Unauthorized personnel
without proper training are at risk of electric shock.
1-8
Warnings, cautions, and notes
WARNING: This product consists of devices that may contain mercury, which must be
recycled or disposed of in accordance with local, state, or federal laws.
(Within this system, the backlight lamps in the monitor display contain
mercury.)
CAUTION: Do not attempt to sterilize or autoclave the ventilator.
CAUTION: To prevent possible damage to the ventilator, use only those cleaning
and disinfecting agents listed in this manual.
CAUTION: To prevent possible damage to the ventilator, do not drip or spray any
liquids directly onto any surface including the front panel,
touchscreen, navigation ring (legacy versions), and Accept button.
CAUTION: Never clean or disinfect the touchscreen with an abrasive brush or
device, since this will cause irreparable damage.
CAUTION: To avoid introducing foreign matter into the ventilator and to ensure
proper system performance, change the air inlet filter at regular
intervals (or as stipulated by your institution).
CAUTION: To ensure proper system performance, use a Respironics-approved air
inlet filter.
CAUTION: Because some environments cause a quicker collection of lint and dust
than others, inspect the filters more often when needed. The air inlet
filter should be replaced; the cooling fan filter should be cleaned.
CAUTION: To prevent possible damage to the ventilator, always ship it with the
original packing material. If the original material is not available,
contact Philips to order replacements.
First-time installation WARNING: Never attempt to disconnect or connect the battery during operation.
CAUTION: To prevent possible damage to the ventilator, always secure it to its
stand or securely place it on a flat, stable surface that is free of dirt
and debris. Do not use the ventilator adjacent to, or stack it with,
other equipment.
Communications WARNING: Connect to the ventilator only items that are specified as part of or
compatible with the ventilator system. Additional equipment connected to
interface medical electrical equipment must comply with the respective IEC or ISO
standards. Furthermore, all configurations shall comply with the
requirements for medical electrical systems (see IEC 60601-1-1 or
clause 16 of edition 3 of IEC 60601-1, respectively). Anybody connecting
additional equipment to medical electrical equipment configures a
medical system and is therefore responsible for ensuring that the system
complies with the requirements for medical electrical systems. Also be
aware that local laws may take priority over the above mentioned
requirements. If in doubt, consult Philips.
WARNING: The USB port is not currently available for use. DO NOT connect or attempt
to power any equipment from the USB port.
1-9
Warnings, cautions, and notes
WARNING: It is the responsibility of the end user to validate the compatibility and use
of information transmitted from the ventilator to the device to be
connected to the ventilator.
WARNING: The data provided through the communications interface is for reference
only. Decisions for patient care should be based on the clinician’s
observations of the patient.
WARNING: To prevent possible patient injury due to nonannunciating alarms, verify
the operation of any remote alarm device before use.
WARNING: To ensure the functionality of the remote alarm, connect only Respironics-
approved cables to the remote alarm port.
CAUTION: The remote alarm port is intended to connect only to an SELV (safety
extra-low voltage and ungrounded system with basic insulation to
ground), in accordance with IEC 60601-1. To prevent damage to the
remote alarm, make sure the signal input does not exceed the
maximum rating of 24 VAC or 36 VDC at 500 mA with a minimum
current of 1 mA.
Diagnostic mode WARNING: To prevent possible patient injury, do not enter the diagnostic mode while
a patient is connected to the ventilator. Verify that the patient is
disconnected before proceeding.
1-10
Chapter 2. Symbols
Refer to these tables to interpret symbols used on the ventilator labels, backup
battery labels, and packaging and on the ventilator screen. To interpret
symbols pertaining to accessories, refer to their instructions for use.
?
Symbol Description
Warning: Risk of explosion. Do not use in the presence of flammable an-
esthetics.
Read the user manual before using the ventilator. Symbol may be accom-
panied by the web address www.Philips.com/IFU to indicate access to
electronic IFUs.
Electronic instructions for use. Indicates that relevant information for use
of the product is available in electronic form.
Medical device
MD
Unique device identifier
UDI
Distributor. Symbol accompanied by address
2-1
Symbols
Symbol Description
Fragile
Keep dry
This end up
Battery
2-2
Symbols
Symbol Description
Brazilian Conformity. Certification by INMETRO (National Institute of Me-
trology, Standardization and Industrial Quality)/SGS (Societe Generale de
Surveillance). One of these three symbols, depending upon available
space.
EC representative
EC REP
Serial number
Order number
Model number
Use by date
USB port
2-3
Symbols
Symbol Description
Oxygen
(Yellow) Warning
Ethernet connection
2-4
Symbols
Symbol Description
Do not block the cooling fan Inlet (at the rear of the ventilator).
Total mass (weight). See page 11-6 for details on physical characteristics
of the ventilator, stand, and accessories.
Hospital-grade
Recycle
Recycle (Taiwan)
廢電池請回收
uR UL recognition symbol
Battery check.
2-5
Symbols
Symbol Description
Rechargeable battery. Symbol is on backup battery.
60 kPa
95 %
Humidity limitation. Indicates the acceptable upper and lower limits of
relative humidity for transport and storage.
10 %
+50 ÛC
Temperature limit. Indicates the maximum and minimum temperature
limits at which the item shall be stored or transported.
-20 ÛC
Battery included
C-Flex feature
Note: 3.00 software and above. HFT is optional for model V60 and
included with model V60 Plus.
2-6
Symbols
Symbol Description
Alarm (audible)
Alarm is silenced
Alarm reset
Informational message
Do not use an NIV mask during high flow therapy (3.00 software and
above, and V60 Plus).
2-7
Symbols
Symbol Description
Ventilator is powered by AC power and the battery is installed.
Vertical autoscale button. Autoscales the Y axis of the graphs to fit the
data currently displayed.
Pause in progress
Time base adjust button. Rescales the X axis of the graph display data at
3, 6, 12, and 24 second increments.
2-8
Symbols
Symbol Description
No valid data to display
Volume, milliliters
2-9
Symbols
2-10
Chapter 3. General information
This manual covers the Respironics V60 and V60 Plus Ventilator
configurations. Both share the same platform. The V60 Plus Ventilator comes
standard with High Flow Therapy (HFT). The V60 Ventilator can be field-
upgraded with HFT, subject to local regulations. For a full list of features,
modes, and options, see "General description" on page 3-3.
NOTE: The 3.00 software upgrade, which permits the activation of HFT, and
the V60 Plus Ventilator are not available in all countries.
Intended use The Respironics V60/V60 Plus ventilator is an assist ventilator and is intended
to augment patient breathing. It is intended for spontaneously breathing
individuals who require mechanical ventilation: patients with respiratory
failure, chronic respiratory insufficiency, or obstructive sleep apnea in a
hospital or other institutional settings under the direction of a physician.
Indications for use The Respironics V60/V60 Plus is an assist ventilator and is indicated for use to
augment patient breathing. The ventilator is indicated for spontaneously
breathing individuals who require mechanical ventilation: patients with
respiratory failure, chronic respiratory insufficiency, or obstructive sleep apnea
in a hospital or other institutional settings under the direction of a physician.
Patient population The Respironics V60/V60 Plus ventilator is intended to support pediatric
patients (children and adolescents, weighing 20 kg (44 lb.) or greater), and
adult patients. The ventilator is also intended for intubated patients meeting
the same selection criteria as the noninvasive applications.
3-1
General information
Contraindications The Respironics V60/V60 Plus Ventilator is contraindicated for patients with
any of the following conditions:
• Lack of spontaneous respiratory drive
• Inability to maintain a patent airway or adequately clear secretions
• At risk for aspiration of gastric contents
• Acute sinusitis or otitis media
• Hypotension
• Untreated pertussis
• Epistaxis (nosebleed)
About CO2 As with mask ventilation in general, patient CO2 rebreathing may occur under
some circumstances. Follow these guidelines to minimize the potential for CO2
rebreathing rebreathing. If rebreathing is a significant concern for a particular patient and
these guidelines are not sufficient to acceptably reduce the potential for CO2
rebreathing, consider an alternative means of ventilation.
• Increase EPAP to decrease the potential for CO2 rebreathing. Higher
pressures produce more flow through the exhalation port, which helps
to purge all CO2 from the circuit to prevent rebreathing.
• Be aware that the potential for CO2 rebreathing increases as
inspiratory time increases. A longer inspiratory time decreases
exhalation time, allowing less CO2 to be purged from the circuit before
the next cycle. In such circumstances, higher tidal volumes further
increase the volume of CO2 rebreathed by the patient.
Potential side effects Advise the patient to immediately report any unusual chest discomfort,
shortness of breath, or severe headache. Other potential side effects of
noninvasive positive pressure ventilation include: ear discomfort,
conjunctivitis, skin abrasions due to mask/patient interface, and gastric
distention (aerophagia). If skin irritation or breakdown develops from the use of
the mask, refer to the accompanying mask instructions for appropriate action.
3-2
General information
General description The Respironics V60/V60 Plus Ventilator (Figure 3-1) is a microprocessor-
controlled, bilevel positive airway pressure (BiPAP) ventilatory assist system
that provides noninvasive positive pressure ventilation (NPPV) and invasive
ventilatory support for spontaneously breathing adult and pediatric patients.
Model
number
Modes, therapies and features. Table 3-1 shows which modes, therapies and
features are included or optional for the V60 and V60 Plus models.
Table 3-1: V60 and V60 Plus comparison
High flow therapy (HFT). High flow therapy provides a set flow of mixed air and
oxygen. Flow and O2 percentage settings are selected by the clinician. HFT is
available for 3.00 software and above, as well as for the V60 Plus.
3-3
General information
Power and gas supplies. The ventilator uses AC mains as its primary power source.
An internal backup battery provides a secondary power source. For more
information, see Table 11-10 on page 11-8.
The ventilator uses high-pressure oxygen. An integral blower pressurizes gas for
delivery to the patient.
NOTE: Oxygen delivered through the compressed gas hose and blower is
used as fresh gas.
Mounting. The ventilator can be mounted to a stand. When equipped with the
optional cylinder holder, the stand can accommodate two E-size oxygen
cylinders. An oxygen manifold kit is available, which allows two oxygen
cylinders and one wall oxygen supply line to be used as inputs to the ventilator.
Communications interface. The ventilator can output data through the RS-232
serial port upon receiving a command from a host computer or bedside
monitoring system. The ventilator is equipped with a remote alarm/nurse call
connection to activate alarms remotely.
3-4
General information
Bacteria filter
Mask
Oxygen
monitor
Humidifier
Patient circuit
Oxygen
cylinder
3-5
General information
Ventilator unit
Depending on the version of the ventilator you have, the Accept button on the
upper-right front of the device may or may not be surrounded by a navigation
ring (scrollable wheel).
Newer versions have a streamlined appearance and the Accept button, and
look like this:
Accept button
Legacy versions have both the navigation ring and Accept button, and look
like this:
Navigation ring
around Accept
button
The photos and illustrations throughout this manual reflect the newer version
of the ventilator (Accept button without navigation ring). For more information
on the functionality differences, see "Navigating the graphical user interface"
on page 3-13.
Figure 3-3 through Figure 3-5 show the controls, indicators, and other
important parts of the ventilator unit.
3-6
General information
8 7 6
Key panel
Number Description
1 Graphical user interface. Color LCD (liquid crystal display) with touchscreen.
3 Proximal pressure port. Connection for tubing that monitors patient pressure in
the patient circuit.
4 Ventilator outlet (To patient) port. Main connection for the patient circuit. Deliv-
ers air and oxygen in prescribed pressures to the patient.
8 ON/Shutdown key with LED. Turns on AC power and initiates ventilator shutdown.
LED is continuously on when AC power is connected.
3-7
General information
1
2
Number Description
2 Air inlet filter (under side panel). Filters the air for delivery to the patient.
3-8
General information
8 7 3 3 6 5 43 2
Number Description
5 Power cord
9 Option labels
3-9
General information
About the backup WARNING: To reduce the risk of power failure to the ventilator, pay close attention to
the battery’s charge level. The battery’s operation time is approximate and
battery is affected by ventilator settings, discharge and recharge cycles, battery
age, and ambient temperature.
NOTE: The backup batteries are intended for short-term use only. They are
not intended to be a primary power source.
NOTE: We recommend that the ventilator’s batteries be fully charged before
you ventilate a patient. If the batteries are not fully charged and AC
power fails, always pay close attention to the level of battery charge.
NOTE: A new backup battery should be installed and charged within one year
of the date of manufacture identified on the battery and on the
shipping box.
NOTE: Storing a battery for an extended period of time after its manufacture
date without being put into service, or at temperatures that exceed its
limits, increases the risk of discharge whereby the battery is unable to
be recharged by the ventilator.
NOTE: Batteries that are not installed in the ventilator should be stored
at -20 to 25ºC and charged at least once per year.
NOTE: Lithium Ion batteries are shipped with a charge level of under 30%,
which may further impact the time until the battery is charged and
discharged.
The internal backup battery protects the ventilator from low, or failure of, AC
(mains) power. If AC power fails, the ventilator automatically switches to
operation on backup battery with no interruption in ventilation. The battery
powers the ventilator until AC power is again adequate or until the battery is
depleted. For electrical specifications, see Table 11-10 on page 11-8.
The ventilator charges the battery whenever the ventilator is connected to AC,
with or without the ventilator switched on. The Battery (charged) LED flashes
to show that the battery is being charged.
Check the battery charge level before putting a patient on the ventilator and
before unplugging the ventilator for transport or other purposes. The power
source symbol at the bottom right-hand corner of the screen shows the power
source in use and, if the ventilator is running on battery, the level of battery
charge (Figure 3-6).
NOTE: The battery charge level displays within about a minute of power on.
3-10
General information
3-11
General information
About the graphical Through the graphical user interface (Figure 3-7) you make ventilator settings
and view ventilator and patient data. During ventilation, the upper screen
user interface
displays alarms and patient data. The middle screen displays real-time
waveforms and alarm and informational messages. The lower screen lets you
access modes and other ventilator settings, display help information, and see
the power status.
Waveforms window 15
(see page 8-1)
100% O2 button
(see page 6-6)
Compressed waveforms window with Alarms/
Messages list
(see page 9-2)
Window/window tabs
(see page 6-1)
3-12
General information
If your ventilator has only the Accept button on the top-right front of the device
(newer versions), you adjust values and navigate the graphical user interface by
using the touchscreen.
If your ventilator has a navigation ring around the Accept button on the
top-right front of the device (legacy versions), you can adjust values and
navigate the graphical user interface by either rotating your finger on the
navigation ring or by using the touchscreen.
After making selections and adjusting values, accept those selections and
apply the changes by either touching the Accept button in the user interface or
by pressing the Accept button (checkmark) on the top-right front of the
ventilator.
To cancel a function and close the window, either select Cancel or touch another
window tab.
To adjust a parameter, touch the arrow button or select the value with the
navigation ring (legacy versions). Each touch changes the value in single
increments or, for parameters with wide ranges, press and hold the arrow key to
make faster changes. The slider flag moves along the setting range scale. Select
Accept to apply.
3-13
General information
Adjustment
Slider flag Setting range scale arrow button
Proposed value
The navigation ring (on legacy versions) also lets you adjust the position of the
cursor in the waveforms window while the screen is frozen. See "Freezing and
unfreezing waveforms" on page 8-3 for more information.
3-14
General information
Starting up the NOTE: Upon power-on the ventilator automatically runs a test of the backup
audible alarm followed by the primary audible alarm. You should hear
ventilator a high-pitched tone, followed by a beep. If you do not hear all of these
sounds, discontinue use of the ventilator and have it serviced.
NOTE: Improper shutdown may cause a Power has been restored message the
next time the ventilator is turned on.
NOTE: If the screen is blank and the dialogue box cannot be displayed, shut
down the ventilator by pressing the ON/Shutdown key, then the Accept
button on the top-right front of the ventilator.
Training Product training is available. Contact your local Philips sales representative or
Philips Customer Support for assistance. Call 1-800-225-0230 for ordering
and 1-800-722-9377 for service.
3-15
General information
3-16
Chapter 4. Principles of operation
The user provides inputs to the ventilator through a touchscreen, a key panel, a
navigation ring (legacy versions), and an Accept button. These inputs become
instructions for the pneumatics to deliver a precisely controlled gas mixture to
the patient. Pressure and flow sensors provide feedback, which is used to
adjust gas delivery to the patient. Monitored data based on sensor inputs is
also displayed by the graphical user interface.
The ventilator’s gas delivery and monitoring functions are cross-checked. This
cross-checking helps prevent simultaneous failure of these two main functions
and minimizes the possible hazards of system failure.
The ventilator has several means to ensure that safe patient or respiratory
pressures are maintained. The maximum working pressure is ensured by the
high inspiratory pressure (HIP) alarm limit. If the set high pressure limit is
reached, the ventilator cycles into exhalation.
4-1
Principles of operation
Pneumatic system The ventilator uses ambient air and high-pressure oxygen (Figure 4-1). Air
enters through an inlet filter. Oxygen enters though a high-pressure inlet, and a
operation
proportioning valve provides the operator-set concentration. The system mixes
the air and oxygen, pressurizes it in the blower, and then regulates it to the
user-set pressure. To do this, the ventilator compares the proximal (patient)
pressure measurement with the ventilator outlet (machine) pressure, and
adjusts the machine pressure to compensate for the pressure drop across the
inspiratory filter, patient circuit, and humidifier. This helps ensure accurate
and responsive pressure delivery and leak compensation.
The ventilator delivers gas to the patient through a main flow (inspiratory)
bacteria filter, a single-limb patient breathing circuit, a humidification device
(optional) and a patient interface such as a mask or ET tube. A pressure tap
proximal to the patient is used to monitor patient pressure. The exhalation port
continually exhausts gas from the circuit during inspiration and exhalation to
minimize rebreathing and ensure CO2 removal.
Baseline pressure
A positive baseline pressure (EPAP or CPAP) may be set for all breaths in all modes.
4-2
Principles of operation
Negative pressures
There are no negative pressures generated during exhalation.
Oxygen concentration
The Respironics V60/V60 Plus Ventilator incorporates an oxygen mixer. Oxygen
concentration can be set in all modes.
Auto-Trak Sensitivity An important characteristic of the Respironics V60/V60 Plus Ventilator is its
ability to recognize and compensate for intentional and unintentional leaks in
the system, and to automatically adjust its triggering and cycling algorithms to
maintain optimum performance in the presence of leaks. This is called Auto-
Trak Sensitivity. The following subsections describe this function in detail.
Triggering
Breaths are patient (flow) triggered in all modes, typically when patient effort
causes a certain volume of gas to accumulate above baseline flow (volume
method). An inspiration is also triggered when the patient inspiratory effort
distorts the expiratory flow waveform sufficiently (shape signal method; see
page 4-4).
Cycling
Cycling to exhalation occurs in these cases:
• Patient expiratory effort distorts the inspiratory flow waveform
sufficiently (shape signal method). See “Shape signal method of
cycling and triggering.” on page 4-4.
• Patient flow reaches the spontaneous exhalation threshold (SET). See
“SET method of cycling.” on page 4-4.
• After 3 seconds at the IPAP level (timed backup safety mechanism)
• When a flow reversal occurs, typically due to a mask or mouth leak
4-3
Principles of operation
Shape signal method of cycling and triggering. The shape signal or “shadow
trigger” method uses a mathematical model derived from the flow signal. A
new flow signal (shape signal) is generated by offsetting the signal from the
actual flow and delaying it (Figure 4-2). This intentional delay causes the flow
shape signal to be slightly behind the patient’s flow signal. If there is a sudden
change in patient flow, the patient’s flow signal crosses the shape signal; this
results in a trigger or a cycle. As a result, a sudden decrease in expiratory flow
from an inspiratory effort will cross the shape signal and create a signal for
ventilator triggering.
Cycle to exhalation
crossover point
Shape
signal
Estimated
patient flow
Trigger to
inspiration
crossover point
Spontaneous
exhalation threshold
4-4
Principles of operation
Leak adaptation
Noninvasive ventilation in particular may involve considerable leakage around
the mask or through the mouth. Some leakage is known or intentional: it is a
characteristic of the mask/patient interface design. So that it can accurately
adjust its baseline flow, the ventilator has you enter the intentional leakage
value specific to the mask/patient interface (“Selecting the mask and
exhalation port” on page 6-12). Other leakage is unpredictable or
unintentional, and it changes as the patient’s breathing pattern changes.
TIME
Spontaneous
trigger
Patient
flow
Adjustment
of baseline
4-5
Principles of operation
Tidal volume adjustment. Every breath, the ventilator compares the inspiratory
and expiratory tidal volumes. Any difference is assumed to be due to an
unintentional circuit leak. The ventilator adjusts the baseline to reduce this
tidal volume difference for the next breath. Figure 4-5 shows how the
ventilator adjusts the baseline.
Additional leak New baseline
introduced
Flow
Volume
Volume adjustment
Auto-Trak+ (optional) The Auto-Trak+ option for the Respironics V60/V60 Plus Ventilator lets you
further adjust the level of Auto-Trak Sensitivity, a feature that recognizes and
compensates for intentional and unintentional leaks. This algorithm has
multiple breath trigger and cycle thresholds. When you adjust Auto-Trak+
settings, you adjust these multiple trigger and/or cycle thresholds
simultaneously, retaining all the auto-adaptive features of Auto-Trak
Sensitivity.
The Normal Auto-Trak settings work well for most patients. Pediatric patients,
however, may benefit from more sensitive trigger settings, while some adult
patients may benefit from more or less sensitive cycle settings.
High flow therapy High flow therapy (HFT) enables delivery of a humidified gas mixture at an
operator-set flow rate via a high flow nasal cannula interface or tracheal
adapter. The principle mechanism of action for high flow therapy is delivering
a known FiO2 at a flow rate equal to or greater than the patient's peak flow,
thus minimizing dilution of the gas.
4-6
Principles of operation
HFT controls flow instead of pressure and is accessed only while in Standby
mode. Patient alarms are not available during high flow therapy. This therapy
is not considered a breath delivery mode.
Ventilation modes The Respironics V60/V60 Plus Ventilator operates in the following ventilation
modes:
• CPAP (continuous positive airway pressure) mode
• S/T (spontaneous/timed) mode
• PCV (pressure-controlled ventilation) mode
• AVAPS (average volume-assured pressure support) mode
• PPV (proportional pressure ventilation) mode (optional)
Table 4-1 summarizes the characteristics of these modes. Note that on the
ventilator, the Timed breath indicator means the breath is ventilator triggered,
while the Spont breath indicator means the breath is patient triggered.
4-7
Principles of operation
CPAP mode
In the CPAP (continuous positive airway pressure) mode, the ventilator
functions as a demand flow system, with the patient triggering all breaths and
determining their timing and size. The patient triggers and cycles based on the
ventilator’s Auto-Trak Sensitivity algorithms. The control settings active in the
CPAP mode are shown in Figure 4-6. Figure 4-7 shows CPAP mode waveforms.
The C-Flex feature setting enhances traditional CPAP by reducing the pressure
at the beginning of exhalation – a time when patients may be uncomfortable
with CPAP – and returning it to the set CPAP level before the end of exhalation.
CPAP
I E
Flow
Volume
Time
4-8
Principles of operation
PCV mode
The PCV (pressure-controlled ventilation) mode delivers pressure-controlled
breaths, either triggered by the ventilator (Timed) or the patient (Spont). The
control settings active in the PCV mode are shown in Figure 4-8. The IPAP
setting defines the applied inspiratory pressure for all breaths. If the patient
fails to trigger a breath through Auto-Trak within the interval determined by the
rate setting, the ventilator triggers a mandatory breath. The I-Time setting is
the cycle criterion for all breaths. Figure 4-9 shows a PCV mode pressure
waveform.
EPAP
Time
Patient-triggered I-Time Machine-triggered
(Spont) breath (Timed) breath
1/Rate
4-9
Principles of operation
S/T mode
The S/T (spontaneous/timed) mode guarantees breath delivery at the user-set
rate. It delivers pressure-controlled, time-cycled mandatory and pressure-
supported spontaneous breaths, all at the IPAP pressure level. If the patient
fails to trigger a breath within the interval determined by the Rate setting, the
ventilator triggers a mandatory breath with the set I-Time. The patient triggers
and cycles based on the ventilator’s Auto-Trak Sensitivity algorithms. The
control settings active in the S/T mode are shown in Figure 4-10. Figure 4-11
shows an S/T mode pressure waveform.
Mandatory
Rise (Timed) breath
IPAP
EPAP
Time
4-10
Principles of operation
AVAPS mode
If the patient fails to trigger a breath within the interval determined by the
Rate control, the ventilator triggers a mandatory breath with the set I-Time.
Mandatory and spontaneous breaths are delivered at a pressure that is
continually adjusted over a period of time to achieve the volume target, VT.
Min P and Max P define the minimum and maximum pressures that can be
applied. The patient triggers and cycles based on the ventilator’s Auto-Trak
Sensitivity algorithms.
The control settings active in the AVAPS mode are shown in Figure 4-12.
Figure 4-13 shows AVAPS mode waveforms.
4-11
Principles of operation
Max P
Mandatory (Timed) Rise
breath
Pressure
Min P
EPAP
I-Time
1/Rate Patient-triggered (Spont)
spontaneous breath
Flow
VT
Volume
Time
4-12
Principles of operation
The physics behind PPV. Two forces oppose ventilation, resistance and
elastance.
Pressure/Flow = Resistance
The compliance of lungs and chest wall for a healthy adult is approximately
0.1 L/cmH2O, resulting in an elastance value of 10 cmH2O/L.
How PPV works. The delivery of a PPV breath is controlled by the maximum
elastance (volume) assist (Max E), maximum resistance (flow) assist (Max R),
and PPV % settings. The actual delivered assistance to overcome elastance is
the product of PPV % and Max E. The actual delivered assistance to overcome
resistance is the product of PPV % and Max R. In general, Max E should be set
relative to the respiratory elastance and Max R should be set relative to the
respiratory resistance, although you do not need to know the actual value of
either to apply PPV. You adjust assist levels to optimize patient comfort. The
resultant pressure support delivered in the PPV mode is the resistance assist
times patient flow plus the elastance assist times the patient volume. Because
the patient completely controls ventilatory output,1 PPV may significantly
improve patient-ventilator synchrony and ultimately, patient comfort.
The PPV backup rate ensures that the patient receives a minimum number of
breaths per minute if the spontaneous breathing rate falls below the Rate
4-13
Principles of operation
setting. If the patient fails to trigger a breath within the interval determined by
the Rate control, the ventilator triggers a Timed (backup) breath with the set
I-Time, Rise, and IPAP settings.
The control settings active in the PPV mode are shown in Figure 4-14.
Figure 4-15 shows PPV mode waveforms. Note how volume and pressure
increase as does the ventilatory demand of the patient. Max V (PPV maximum
volume limit) and Max P (PPV maximum pressure limit) are used to prevent
the delivery of excessive pressure or volume. More information about these
limits is provided in “About Max V and Max P alarms and alarm limits” on
page 6-7.
Max V
Volume
Time
Max P
Pressure
EPAP
4-14
Principles of operation
Oxygen mixing The ventilator’s oxygen mixer regulates and proportions oxygen into the air
from the blower according to the O2 setting. The delivered oxygen accuracy is
±5% of the set value up to the maximum oxygen flow available. The ventilator
can deliver up to 240 L/min of air/oxygen mix to assist in managing
uncontrolled leaks during noninvasive ventilation.
Many hospital oxygen supply systems, however, cannot meet such high flow
demands. Under extraordinary conditions (high O2 setting plus high leak, and/
or high patient demand) where demand exceeds available oxygen system flow,
the ventilator provides additional air flow from the blower to ensure the target
pressure is met. Under such conditions, the accuracy of delivered oxygen may
be affected. Figure 4-16 shows the effect on the delivered oxygen
concentration as the maximum oxygen system flow is exceeded. This graph
assumes a continuous flow demand. Normally the higher “peak” flow is only
needed during inspiration, so this is a worst case scenario.
100
95
90
85
(%)
80
Concentration
concentration
75
70
65
O2%
Oxygen
60
55
50
45
40
130 140 150 160 170 180 190 200 210 220 230 240
Total
Total Ventilator
ventilator Flow
flow L/min
(L/min)
Assumptions: At an O2 setting of 100% and an oxygen supply with a 50 psig inlet pressure capable
of delivering up to160 L/min.
4-15
Principles of operation
4-16
Chapter 5. Setting up the ventilator for use
Set up the ventilator for each patient use as described in this chapter. For first-
time installation, refer to Appendix A. For use with high flow therapy (HFT), set
up the ventilator as described in this chapter, then refer to Chapter 7, High
flow therapy.
Connecting oxygen WARNING: Connect the ventilator only to an appropriate medical-grade oxygen
source.
WARNING: To ensure accuracy of oxygen administration and to monitor for the
presence of contamination (incorrect gas connected), use an external
oxygen monitor to verify the oxygen concentration in the delivered gas.
WARNING: To reduce the risk of fire, do not use a high-pressure oxygen hose that is
worn or contaminated with combustible materials like grease or oil.
WARNING: To reduce the risk of hypoxia, connect only oxygen to the high-pressure
connector at the rear of the ventilator.
WARNING: To reduce patient risk of oxygen toxicity, keep free-flowing oxygen away
from air inlet of ventilator.
CAUTION: To prevent possible damage to the ventilator, ensure that the
connection to the oxygen supply is clean and unlubricated, and that
there is no water in the oxygen supply gas.
Installing an oxygen Install an Analytical Industries 2000M oxygen analyzer/monitor, and follow the
manufacturer’s instructions for setup, alarms, and calibration.
analyzer/monitor
The Analytical Industries 2000M monitor includes user-settable high and low
oxygen % alarms and is approved for use with the V60/V60 Plus Ventilator.
Refer to the monitor instructions for use for detailed instructions on the proper
setup and operation of the oxygen monitor.
NOTE: The V60/V60 Plus Ventilator also incorporates a loss of oxygen supply alarm to
further protect the patient from low oxygen supply pressure conditions.
5-1
Setting up the ventilator for use
Connecting to AC WARNING: To reduce the risk of electric shock, connect the ventilator to an AC
supply mains with protective earth only.
power
WARNING: Do not use extension cords, adapters, or power cords with the ventilator
that are not approved by Respironics.
WARNING: To prevent unintentional disconnection of the power cord, always use the
correct, Philips-supplied power cord and lock it into place with the power
cord retainer before you switch the ventilator on. The retainer is designed
to hold the connector end of the Philips-supplied cord securely in place.
WARNING: To reduce the risk of electric shock, regularly inspect the AC power cord
and verify that it is not frayed or cracked.
WARNING: To reduce the risk of strangulation, route the power cord to avoid
entanglement.
CAUTION: For 120 V equipment, grounding reliability can only be achieved
when it is connected to an equivalent receptacle marked “hospital
only” or “hospital grade.”
Plug the power cord into a grounded outlet that supplies AC power between
100 and 240 V, 50/60 Hz.
Always check the reliability of the AC outlet. If you are using a 120 V outlet,
make sure that it is hospital grade.
5-2
Setting up the ventilator for use
Installing the patient WARNING: To reduce the risk of strangulation from patient tubing, use a tubing
support arm and secure the proximal pressure line with clips.
circuit
WARNING: To prevent possible patient injury and possible water damage to the
ventilator, make sure the humidifier is set appropriately.
WARNING: To prevent possible patient injury and equipment damage, do not turn the
humidifier on until the gas flow has started and is regulated. Starting the
heater or leaving it on without gas flow for prolonged periods may result
in heat build-up, causing a bolus of hot air to be delivered to the patient.
Circuit tubing may melt under these conditions. Turn the heater power
switch off before stopping gas flow.
WARNING: To reduce the risk that the patient will aspirate condensed water from the
breathing circuit, position any humidifier lower than both the ventilator
and the patient.
WARNING: To reduce the risk of fire, use only patient circuits intended for use in
oxygen-enriched environments. Do not use antistatic or electrically
conductive tubing.
WARNING: To prevent patient or ventilator contamination, always use a main flow
bacteria filter on the patient gas outlet port. Filters not approved by
Respironics may degrade system performance.
WARNING: During ventilation, patient exhalate is released into room air. Use of a
patient circuit with a filter on its exhalation port is recommended.
WARNING: To reduce the risk of bacterial contamination or damage, handle bacteria
filters with care.
WARNING: Avoid adding any components to the patient circuit that are not absolutely
necessary. Additional components installed in the patient circuit can
change the pressure gradient across the ventilator breathing system,
increase the dead space, and adversely affect the ventilator performance.
WARNING: Any additional accessories in the patient circuit may substantially
increase flow resistance and impair ventilation.
WARNING: Avoid adding resistive circuit components on the patient side of the
proximal pressure line. Such components may defeat the disconnect
alarm.
WARNING: Using a jet nebulizer can cause inadvertent alarms and affect the
accuracy of delivered FiO2. To reduce patient risk, use only an approved
nebulizer.
NOTE: Bacteria filter must be installed onto gas outlet.
NOTE: Resistive components can include but are not limited to HMEs,
proximal flow sensors, a filter at the patient connection, or a narrow
diameter circuit attached to a mask.
NOTE: Under extreme conditions and a missing, ruptured, or defective
bacteria filter, the entire gas pathway can become contaminated with
bodily fluids or exhaled gas.
Install the patient circuit as shown in this section. For a list of compatible
parts and accessories offered by Philips, see “Parts and accessories” on
page C-1.
5-3
Setting up the ventilator for use
Assemble the patient circuit, including the main flow (inspiratory) bacteria
filter, proximal pressure line, oxygen sensor tee, and if desired, humidifier and
nebulizer.
Figure 5-1 shows the circuit configuration for noninvasive ventilation or high flow
therapy. For details on high flow therapy setup, see “High flow nasal cannula
setup” on page 7-2.
Figure 5-2 and Figure 5-3 show circuit configurations for noninvasive and
invasive ventilation. Follow the manufacturers’ instructions for use for the
individual parts.
www.aerogen.com/nebulization-product-support
5-4
Setting up the ventilator for use
Proximal
pressure
port
Ventilator
outlet
Humidifier
5-5
Setting up the ventilator for use
Proximal
pressure
port
Ventilator
outlet
Bacteria filter
5-6
Setting up the ventilator for use
NOTE: This circuit setup is recommended for both noninvasive and invasive
ventilation. Figure 5-3 shows an invasive circuit as an example.
Proximal
pressure
port
Ventilator
outlet
Bacteria filter
Proximal filter
Proximal pressure line
Water trap
Humidifier
Connecting external Connect the ventilator to a remote alarm (nurse call) device and a patient
monitor or other external device, if applicable.
devices
The Respironics V60/V60 Plus Ventilator can communicate with a Philips
patient monitor using the IntelliBridge Open Interface. See “Using Philips
monitors and the IntelliBridge or VueLink Open Interfaces” on page B-2. The
ventilator also supports the VueLink Open Interface. VueLink has been
replaced by IntelliBridge, but information is included in this manual for
backwards compatibility. See “Data display” on page B-3.
For more information about connecting with non-Philips systems, contact your
Philips representative.
5-7
Setting up the ventilator for use
Before placing a WARNING: To ensure the ventilator’s safe operation, always verify ventilator
operation as described in “Verify ventilator operation” on page 5-8 before
patient on the using the ventilator on a patient. If the ventilator fails any tests, remove it
ventilator from clinical use immediately. Do not use the ventilator until necessary
repairs are completed and all tests have passed.
WARNING: To reduce the risk of power failure to the ventilator, pay close attention to
the battery’s charge level. The battery’s operation time is approximate and
is affected by ventilator settings, discharge and recharge cycles, battery
age, and ambient temperature.
NOTE: If the ventilator has a backup battery, the battery must be adequately
charged to verify operation. Recharge as necessary before verifying
operation. Based on the age and state of the battery, it may take up to
16 hours or more to fully charge.
NOTE: The backup batteries are intended for short-term use only. They are
not intended to be a primary power source.
NOTE: We recommend that the ventilator’s batteries be fully charged before
you ventilate a patient. If the batteries are not fully charged and AC
power fails, always pay close attention to the level of battery charge.
5-8
Setting up the ventilator for use
Running alarm tests The ventilator performs a self-check during start-up and continuously during
operation. Alarm functionality is verified by this self-check. You may also want
to run alarm tests, which demonstrate the alarms’ operation. Follow these
steps to perform the tests.
Preparation
2. Set the mode to S/T and make the following control settings: Rate:
4 BPM, IPAP: 10 cmH2O, EPAP: 6 cmH2O, I-Time: 1 sec, Rise: 1,
Ramp: Off, O2: 21%.
2. VERIFY that the High Inspiratory Pressure alarm is activated, the ventilator
cycles into exhalation, and pressure falls to 6 cmH2O (the EPAP
level).
5-9
Setting up the ventilator for use
Patient Disconnect
4. VERIFY that the alarm resets and that the ventilator automatically
resumes ventilation.
5-10
Setting up the ventilator for use
Using the ventilator WARNING: Always check the status of the oxygen cylinders before using the
ventilator during transport.
for intra-hospital
WARNING: To reduce the risk of power failure to the ventilator, pay close attention to
transport the battery’s charge level. The battery’s operation time is approximate and
is affected by ventilator settings, discharge and recharge cycles, battery
age, and ambient temperature.
WARNING: The V60/V60 Plus Ventilator requires a pressurized oxygen supply that
provides a minimum flow of 175 SLPM. Do not use any devices such as
valves, hoses, Grab n' Go regulators or other brands of combined cylinder/
regulators that limit supply of oxygen flow below 175 SLPM.
WARNING: Do not leave the ventilator unattended when stationed on an incline.
5-11
Setting up the ventilator for use
90
80
70
Duration (min)
60
50
40
30
20
10
0
30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
FIO2 (%)
Leak of 10 L/min
Leak of 20 L/min
Leak of 30 L/min
Leak of 40 L/min
Leak of 50 L/min
140
120
Duration (min)
100
80
60
40
20
0
30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
FIO2 (%)
Leak of 20 L/min
Leak of 10 L/min
Leak of 30 L/min
Leak of 40 L/min
Leak of 50 L/min
5-12
Setting up the ventilator for use
Storing the ventilator See “Storage between patient use” on page 10-8 for information about storing
the ventilator.
between patient use
MRI safety WARNING: The V60/V60 Plus Ventilator is MR Unsafe. Keep it outside the MRI scan
room (Zone IV). It represents a projectile hazard.
information
Security and Privacy To develop a security strategy related to the use of the ventilator, refer to the
Hospital Respiratory Care product security guide. Download it from:
Information www.philips.com/hrcmanuals.
5-13
Setting up the ventilator for use
5-14
Chapter 6. Operation
After power-on, the ventilator starts up in the mode and with the settings that
were active before last power down. Check these settings and adjust as
required. You must be familiar with using the touchscreen and navigation ring
(legacy versions) to select, adjust, activate, and confirm parameters. For
details, see “Before placing a patient on the ventilator” on page 5-8.
Access the ventilator setting windows from the tabs at the bottom of the
screen.
page 6-3 page 6-12 page 6-2 page 6-17 page 6-20 page 6-22
6-1
Operation
Changing the mode The active ventilation mode is displayed in the bottom, left-hand corner of the
screen. Change the mode as follows. For details on modes, see “Ventilation
modes” on page 4-7.
Active
mode
6-2
Operation
Changing control Table 6-3 on page 6-23 is an alphabetical list of the control settings with their
ranges. Table 11-2 on page 11-2 shows the control settings applicable to the
settings
different modes. For more information on control settings as they apply in the
different ventilation modes, see “Ventilation modes” on page 4-7.
NOTE: During a batch setting change, you cannot change the Ramp Time
setting when a ramp is active.
Active
mode
6-3
Operation
3. The setting window opens. Adjust the setting. Select Accept to apply.
Current
settings area
Proposed value
6-4
Operation
Using the Ramp Time The Ramp Time function helps your patient adapt to ventilation by gradually
increasing inspiratory and expiratory pressure (IPAP and EPAP/CPAP) from
function
subtherapeutic to user-set pressures over a user-set interval. Table 6-3 on
page 6-23 describes this function’s principles of operation.
The ramp starts. As the ramp progresses, the Ramp Time button
graphic fills in.
2. To change the ramp interval or to end the ramp, select the Ramp Time
button again. The Ramp in Progress window opens.
Ramp
status
Bar
3. To end the ramp and apply the full IPAP and EPAP/CPAP immediately,
select End Ramp.
4. To end the ramp and start a new one, select Start New Ramp. The
Ramp Time setting window opens again so that you can set up a new
ramp.
6-5
Operation
Using the 100% O2 NOTE: The 100% O2 feature is available in Revision 2.30 software and
above.
function
While 100% oxygen delivery is active, you can press the +2:00 button
to add two minutes more. Press Cancel to stop.
6-6
Operation
Using PPV Follow these instructions to set up the ventilator in the PPV mode, referring to
Figure 6-3. For principles of operation, see “PPV mode (optional)” on page 4-13.
2. Set EPAP, O2, alarm limits, and backup settings to appropriate values.
The HIP alarm limit should be greater than Max P. See “Principles of
operation” on page 4-1 for a detailed explanation of these settings.
4. Set alarm limits to appropriate values. The HIP alarm limit should be
greater than the Max P.
WARNING: PPV limits are not intended to be the primary ventilator alarms and should
not be substituted for the alarms found in the Alarm Settings window.
WARNING: To prevent the delivery of excessive pressure or volume, set the PPV
limits appropriately. Delivery of excessive pressure or volume can occur
from a sudden increase in mask leak, inappropriate settings, or a plugged
or kinked proximal pressure line. Conversely, insufficient treatment may
result if limits are set too low.
When the Max V (PPV maximum volume limit) is reached, the breath is
terminated and a message is displayed. After the limit is reached in three
consecutive breaths, the audible alarm sounds. A PPV waveform with Max V is
shown in Figure 6-1.
6-7
Operation
VT Max V
Inspiration terminated
Volume
Max V
Sudden increase
in flow
Flow
Time
When the Max P (PPV maximum pressure limit) is reached, pressure is limited
but the breath is not terminated, and a message is displayed. After the limit is
reached in three consecutive breaths, the audible alarm sounds. A PPV
waveform with Max P is shown in Figure 6-2.
Pressure limited Exhalation cycled by patient
Sudden increase
in target pressure
Max P
Pressure
EPAP
The VT (estimated exhaled tidal volume) measurement may remain below the
set Max V limit even though the inspired volume exceeds Max V. This results
from variable leakage, which reduces the exhaled volume in relation to the
inspired volume.
6-8
Operation
NOTE: You may also need to adjust PPV % according to patient response, as
you do for the other PPV settings described below. Mask leakage,
especially a sudden increase, is interpreted as patient effort by the
ventilator and assisted accordingly; this may necessitate lowering the
PPV % setting. However, the best solution is to maintain a minimal
leak.
1. Set EPAP, O2, alarm limits, and backup settings to appropriate values.
The HIP alarm limit should be greater than Max P.
6-9
Operation
2. Adjust Max E:
a. Evaluate the patient. Check whether any of these conditions is
true:
• The patient says they are getting too much air, pressure, or
volume
• The patient is using accessory muscles to actively stop
inspiration
• The Max V or Max P limit is reached
• The mask leak has suddenly increased
b. If none is true, increase Max E in increments of 2 cmH2O/L while
continuing to evaluate the patient’s response.
c. If any is true, decrease Max E by 2 cmH2O/L, and re-evaluate.
Repeat to optimize patient comfort.
6-10
Operation
Start
Max R
Make initial settings: titration
EPAP: 4 cmH2O
O2: Current setting or per prescription
Max P: 25 cmH2O
Max V: 1000 to 1500 mL Does the patient say the air Yes
PPV %: 80 to 100% is coming too fast?
Max E: 5 cmH2O/L
Max R: 2 cmH2O/L/s
HIP: > Max P
Other settings: Per usual protocol No
Yes
No Was the Max V or Max P
limit reached?
No Yes
Has the mask leak suddenly
increased?
Yes No
Was the Max V or Max P
limit reached?
Increase Max R by
1 cmH2O/L/s
No
Increase Max E by
2 cmH2O/L Titrate PPV % downward as tolerated
Reduce Max E
by 2 cmH2O/L for patient comfort End
6-11
Operation
Changing alarm WARNING: To prevent possible patient injury, avoid setting alarm limits to extreme
values, which can render the alarm system useless.
settings
Some ventilator alarm settings are operator adjustable. You can adjust these at
any time. Table 6-4 on page 6-26 lists the alarm settings and their ranges.
2. Select the desired setting, adjust it, and select Accept to apply.
The ventilator annunciates an alarm when a monitored value goes out of the
range bounded by the alarm limits.
Selecting the mask To be able to display full leakage data plus accurate tidal and minute volumes,
the ventilator must know the intentional leak characteristics of the specific
and exhalation port
mask/patient interface and exhalation port.
After power-on, the Messages list displays the current mask and port settings
for 5 minutes.
2. Select Mask/Port.
6-12
Operation
Leak 3 AP111
6-13
Operation
4. Select the desired exhalation port type (Table 6-2). Select Accept to
apply.
6-14
Operation
FEP No
Philips Respironics Filtered Exhalation Port
DEP No
Philips Respironics Disposable Exhalation
Port
Whisper Swivel No
Philips Respironics Whisper Swivel
PEV Yes
Philips Respironics Plateau Exhalation Valve
Other Yes
Exhalation port not supplied by Philips Respi-
ronics.
None No
No inline circuit exhalation port
* Depending on your software version, your available exhalation port selections may vary.
5. Run the exhalation port test if indicated in the table (see “Running
the exhalation port test” on page 6-16 for instructions).
CAUTION: If you selected PEV or Other as an exhalation port, you must run an
exhalation port test.
NOTE: If the exhalation port test is not run or if it fails, the intentional leak is
unknown. Tot.Leak rather than Pt. Leak is displayed in the patient
data window.
6-15
Operation
Running the The exhalation port test is required and its window is automatically displayed
when PEV or Other is selected.
exhalation port test
Procedure
Run the test as follows:
Progress
bar
6-16
Operation
Troubleshooting
If Test Failed is displayed, check for leaks in the patient circuit, and install an
exhalation device with lower leak characteristics. Repeat test. If the exhalation
port test fails again, the intentional leak is unknown and Tot.Leak rather than
Pt. Leak is displayed in the patient data window.
Other functions: the From the Menu window you can adjust user preferences.
Menu window
Brightness
Use Brightness to adjust the screen for optimum daytime or nighttime viewing.
Loudness
WARNING: Set the alarm loudness above the ambient level. Setting the alarm
loudness too low may prevent recognition of alarm conditions.
WARNING: Avoid blocking the alarm speakers beneath the ventilator.
Use Loudness to adjust the volume of the alarm and touchscreen audible
feedback. You will hear audible feedback as you go through the selections.
The Alarm Volume Escalation status is also displayed on this screen. See
“Alarm Volume Escalation” on page E-11 for more information.
6-17
Operation
Mask/Port
See “Selecting the mask and exhalation port” on page 6-12.
Screen Lock
Screen Lock deactivates all buttons and tabs on the touchscreen except Alarm
Silence, Alarm Reset, the Alarm/Message button, and Help. Tabs are grayed
out as in this example.
To unlock the screen, press the Accept button on the top-right front of the
ventilator.
Auto-Trak+
The Normal Auto-Trak settings work well for most patients. Pediatric patients,
however, may benefit from more sensitive trigger settings, while some adult
patients may benefit from more or less sensitive cycle settings.
6-18
Operation
Proposed value
Auto-Trak+
active
Additionally, after power-on the Messages list displays the Auto-Trak+ settings
for 5 minutes.
6-19
Operation
Standby Standby lets you safely suspend ventilation to temporarily disconnect the
patient from the ventilator or to set up the ventilator before connecting the
patient. Alarms are disabled during standby.
You can also change ventilator settings and most menu functions during
standby. The settings changes are effective when you exit standby. Enter
standby as follows:
6-20
Operation
2. Disconnect the patient from the ventilator now. The ventilator enters
standby and displays the Standby screen.
NOTE: You can also manually resume ventilation with the Restart Mode
button.
6-21
Operation
Help
message
6-22
Operation
Modes
Control settings
CPAP Continuous positive airway pressure. The baseline pressure applied during the expiratory 4 to 25 cmH2O
phase.
Applies in CPAP mode only.
E-Cycle (option- Expiratory Cycle Sensitivity. Auto-Trak+ employs several algorithms to determine the point -2, -1, Normal,
al) at which the ventilator cycles into exhalation. This setting adjusts all algorithms simulta- +1 to +6
neously. At the lowest setting (-2), inspiration terminates later, resulting in the longest in-
spiratory time. At the highest setting (+6), inspiration terminates earlier, resulting in the
shortest inspiratory time. Normal is the Auto-Trak setting used when Auto-Trak+ is not en-
abled.
Applies only when the optional Auto-Trak+ feature is installed.
6-23
Operation
I-Time (Inspira- Time to deliver the required gas. Inverse ra- 0.30 to
tory Time) tio ventilation is not allowed. 3.00 secs
Max E The maximum elastance (volume assist) value used by the PPV mode to overcome the 0 to
elastance of the patient's lungs. See also PPV % setting. 100 cmH2O/L
Applies in PPV mode only.
Max P (PPV The maximum pressure to be applied. When the limit is reached, the ventilator limits the 5 to 40 cmH2O
Maximum Pres- pressure and displays a PPV Max P alarm message. If the condition persists for three con-
sure Limit) secutive PPV inspirations, an audible alarm also sounds.
Applies in PPV mode only.
WARNING:PPV limits are not intended to be the primary ventilator alarms and should not be
substituted for the alarms found in the Alarm Settings window.
WARNING:To prevent the delivery of excessive pressure or volume, set the PPV limits
appropriately. Delivery of excessive pressure or volume can occur from a sudden
increase in mask leak, inappropriate settings, or a plugged or kinked proximal
pressure line. Conversely, insufficient treatment may result if limits are set too low.
Max R The maximum resistance (flow assist) value used by the PPV mode to overcome pulmo- 0 to 50 cmH2O/
nary resistance. See also PPV % setting. L/s
Applies in PPV mode only.
Max V (PPV The maximum volume to be delivered. When the limit is reached, the ventilator terminates 200 to
Maximum Vol- the breath and displays a PPV Max V alarm message. If the condition persists for three 3500 mL
ume Limit) consecutive PPV inspirations, an audible alarm also sounds.
Applies in PPV mode only.
WARNING:PPV limits are not intended to be the primary ventilator alarms and should not be
substituted for the alarms found in the Alarm Settings window.
WARNING:To prevent the delivery of excessive pressure or volume, set the PPV limits
appropriately. Delivery of excessive pressure or volume can occur from a sudden
increase in mask leak, inappropriate settings, or a plugged or kinked proximal
pressure line. Conversely, insufficient treatment may result if limits are set too low.
6-24
Operation
Rise (Rise Time) Speed with which inspiratory pressure rises 1 to 5 (1 is fast-
to the set (target) pressure. est)
If the Rise Time is insufficient to reach the
target IPAP pressure, adjust the Rise Time
or I-Time setting.
6-25
Operation
Trigger Trigger Sensitivity. Auto-Trak+ employs several algorithms to determine the point at which Normal, +1 to
(optional) the inspiration begins. The larger the value, the more sensitive the trigger (that is, the pa- +7
tient can trigger inspiration with less effort). Normal is the Auto-Trak setting used when
Auto-Trak+ is not enabled.
Applies only when the optional Auto-Trak+ feature is installed.
VT (AVAPS Tar- Target tidal volume to be delivered during inspiration. The ventilator meets this target by 200 to
get Tidal Vol- adjusting the inspiratory pressure with each breath. 2000 mL
ume) Applies in AVAPS mode only.
Table 6-4 lists the settable alarms. (For a complete list of non-settable alarms,
including Patient Disconnect, Occlusion, Pressure Regulation High, and other
alarms, refer to Table 9-3 on page 9-7.)
LIP (Low Inspiratory Pres- Low pressure at the patient OFF to 40 cmH2O
sure Alarm) airway.
6-26
Operation
NOTE: In the S/T and PCV modes, the LIP alarm should
be set 3-5 cmH2O below the IPAP level. When
set in this manner, the alarm works in
conjunction with the LIP T alarm to indicate if
there is a failure to trigger between the two
pressure levels. It will also alert the clinician to
pressure degradation due to excessive leaks. See
figure below.
HIP
alarm
IPAP
LIP
alarm
EPAP
LIP T (Low Inspiratory Pres- The interval from the detec- 5 to 60 secs
sure Delay Time) tion of low inspiratory pres-
sure until the alarm
becomes active.
•
Lo V E (Low Minute Ventila- Low expiratory minute vol- OFF to 99.0 L/min
tion Alarm) ume.
6-27
Operation
6-28
Chapter 7. High flow therapy
The high flow therapy (HFT) feature is available for 3.00 software and above,
as well as V60 Plus. HFT is accessed from the Standby mode. For more
information, see “Standby” on page 6-20.
WARNING: When transitioning from a high flow therapy interface to an NIV mask,
ensure that an exhalation port is placed in the circuit and is unobstructed
to reduce the risk of CO2 rebreathing.
WARNING: When transitioning from ventilation to high flow therapy, remove the NIV
mask and use only a Philips-approved high flow patient interface to
minimize pressure build-up and patient discomfort.
WARNING: When transitioning from high flow therapy to ventilation, remove the high
flow nasal cannula as it is restrictive and may defeat alarms such as
patient disconnect. Using a high flow nasal cannula in an NIV mode may
lead to hypercarbia due to the inability to provide pressure support.
WARNING: Patient alarms are not available during high flow therapy (HFT) as the
therapy uses an open system. A high flow nasal cannula occupies only a
portion of the nares and patients can breathe through their mouth, which
prevents estimation of patient parameters such as tidal volume,
respiratory rate, pressure, and minute ventilation. Provide external
monitoring, including oximetry, to inform the clinician of a change in the
patient's condition.
WARNING: During high flow therapy (HFT), verify that an occlusive patient interface
is not being used. Occlusive patient interfaces include a cannula fully
sealed within the nares, an NIV mask, or a direct connection to a
tracheostomy tube or endotracheal tube. Remove any occlusive interface
immediately as this may expose the patient to unintended high pressures.
NOTE: High flow therapy (HFT) is accessed only from the Standby window.
Standby mode cannot be entered if a high flow nasal cannula is
connected to the circuit.
Circuit setup See “Installing the patient circuit” on page 5-3 for circuit configuration.
7-1
High flow therapy
High flow nasal Use either the AC611 high flow nasal cannula with FEP Connector (Figure 7-1)
or the AC611 high flow nasal cannula 22 mm (Figure 7-3), which connects
cannula setup
directly to the patient circuit.
NOTE: This section applies only if you are using the AC611 high flow nasal
cannula with filter exhalation port (FEP) connector (“FEP Connect”)
to administer high flow therapy.
1. Insert the AC611 high flow nasal cannula with FEP Connector into the
FEP, making sure the perforations in the port are completely blocked.
FEP Connect
blocking insert
Figure 7-1: High flow nasal cannula using the FEP Connect
3. Leave the other end of the proximal pressure line connected to the
FEP and anchor the tubing to the breathing circuit using several
tubing clips (included with most circuits), as shown in Figure 7-2.
7-2
High flow therapy
Proximal
pressure
port
FEP
Proximal pressure
line
Tubing clips
Figure 7-2: Proximal pressure line anchored to circuit with tubing clips
7-3
High flow therapy
Remove the FEP, and connect the high flow nasal cannula with 22 mm
connector directly to the circuit.
22 mm connector
FEP
Changing from an NIV Follow these instructions to use the V60/V60 Plus Ventilator for high flow
therapy (HFT).
mode to high flow
therapy 1. Select Standby. The Entering Standby window opens.
4. Select HFT.
7-4
High flow therapy
5. From the Active Mode window, you can adjust Flow and O2%.
9. Note the low priority alarm stating that patient alarms are disabled
during HFT. Press alarm reset to confirm this message.
Viewing and pausing A flow graph is displayed during high flow therapy. Press the Pause button to
view an event.
the HFT graph
7-5
High flow therapy
Changing from high 1. Verify that the high flow nasal cannula is removed from the patient
and disconnected from patient circuit.
flow therapy to an NIV
mode 2. Select Standby to open the Standby window.
HFT alarms and Table 7-1 is a list of alarms and other messages displayed by the ventilator,
along with descriptions, suggested corrective actions, and other information.
messages
The ID (identifier) listed with the priority type is the priority number of the
alarm. This priority number determines the order of alarm message display.
Unless otherwise indicated, alarms listed.
7-6
High flow therapy
Table 7-1: HFT Alarm and other messages: summary and troubleshooting
Cannot Reach Target Displays when HFT (high Check the patient. Check Low No Yes Yes
Flow flow therapy) is active. In- that the high flow nasal (66)
dicates that flow target is cannula size is appropri-
not achieved. ate for the flow setting.
Check that an occlusive
interface is NOT in use (a
cannula fully sealed with-
in the nares, an NIV mask
or direct connection to an
ETT/trach). Check for an
occlusion, kink or liquid in
the patient circuit.
Patient alarms are Displays when HFT (high Manually reset to confirm Low/ Yes No Yes
disabled during HFT flow therapy) is active. Pa- and clear the audible Infor-
tient alarms are not avail- alarm. mation
able in this therapy. (68)
Patient Circuit Oc- Displays when HFT (high Check the patient. Check High No Yes Yes
cluded flow therapy) is active. that an occlusive interface (67)
Gas flow to the patient is is NOT in use (a cannula
obstructed. fully sealed within the na-
res, an NIV mask or direct
connect to an ETT/trach).
Check for an occlusion,
kink or liquid in the pa-
tient circuit. If problem
persists, provide alterna-
tive ventilation.
Check Vent: Proxi- Displays when HFT (high When using a high flow High Yes No No
mal Pressure Sensor flow therapy) is active. nasal cannula with FEP (12)
Range Error Proximal pressure is out of Connect, the proximal
range. pressure line should be
disconnected from the
ventilator port during HFT.
If this message is seen
when switching the pa-
tient from ventilation to
HFT, check to make sure
the proximal pressure line
is disconnected.
If the message still oc-
curs, provide alternative
ventilation and have the
ventilator serviced.
7-7
High flow therapy
7-8
Chapter 8. Patient monitoring
The ventilator displays numeric patient data in the patient data window and
real-time graphics in the waveform window (Figure 8-1). Numeric patient data
is updated every breath. Table 8-1 on page 8-2 lists the ventilator’s monitored
parameters.
Breath
phase/trigger
indicator
Numeric
patient data
Airway pressure window
•
(P), flow ( V ), and
volume (V)
waveforms
IPAP
Pause button
EPAP/
Vertical CPAP
autoscale
button
Waveform
Time base adjust window
button
Cursor
Display conventions The following symbols may be displayed in place of numeric values:
8-1
Patient monitoring
Table of monitored
parameters
Parameter Definition
Breath phase/trigger indicator Spont (spontaneous): Inspiratory phase, patient-triggered breath (color: turquoise)
Timed: Inspiratory phase, ventilator-triggered breath (color: orange)
Exhale: Expiratory phase (color: blue)
PIP Peak inspiratory pressure. The highest patient pressure during the previous breath cycle.
Pt. Leak Estimated patient leak or unintentional leak. Average during the previous breath cycle. Dis-
played only after a suitable exhalation port and mask/patient interface are selected.
Pt. Trig Patient-triggered breaths, as a percentage of total breaths over the last 15 minutes.
Rate Respiratory rate or total breathing frequency. Moving average over the last 6 breaths (or
15 seconds).
TI/TTOT Inspiratory duty cycle or inspiration time divided by total cycle time. Moving average over the
last 8 breaths.
Tot.Leak Estimated total leak. Average during the previous breath cycle. Displayed before a suitable
exhalation port and mask/patient interface are selected.
Estimated minute ventilation. The product of tidal volume (spontaneous and timed) and rate
VE (spontaneous and timed). Moving average over the last 6 breaths.
VT Estimated exhaled tidal volume. Moving average over the last 6 breaths. It is body tempera-
ture pressure saturated (BTPS) compensated.
Waveform window
P waveform Airway pressure. Where applicable, dotted lines represent target IPAP and EPAP.
Estimated patient flow. The total delivered flow minus the leak flow (Tot.Leak), where Tot.Leak
V waveform includes known (intentional) leakage through the exhalation port plus any unintentional leak-
age in the circuit or at the mask/patient interface.
V waveform Estimated patient volume. In AVAPS mode, the dotted line represents target volume.
Scaling the waveform Scale the vertical and horizontal waveform axes with the scale buttons.
axes
The vertical scale button autoscales the Y axes to best fit the current
data.
8-2
Patient monitoring
Freezing and Freeze waveforms for extended viewing by selecting the pause button
to the left of the waveform window.
unfreezing waveforms
The cursor makes one complete sweep across the waveform and then
displays the pause in progress symbol. The graphic display is then
frozen, and the cursor is visible in the middle of the display
(Figure 8-2). Reposition the cursor by touching the waveform screen
or with the navigation ring (legacy versions). Data values at cursor
location for pressure, flow, and volume are displayed in the white
boxes.
Resume
button
unfreezes
waveforms
Measurements at
cursor
Cursor
8-3
Patient monitoring
8-4
Chapter 9. Alarms, messages, and troubleshooting
Alarms and messages on the ventilator alert you to situations that require your
attention. The ventilator can also actuate remote alarms. Figure 9-1 on page 2
shows the visual alarm characteristics. Table 9-3 on page 9-7 summarizes the
different types of alarm and tells you how to respond to each.
Responding to alarms WARNING: If AC power fails and the backup battery is not installed or is depleted, an
audible and visual alarm annunciates for at least 2 minutes. Immediately
discontinue ventilator use and secure an alternative means of ventilation.
As in most ventilators with passive exhalation ports, when power is lost,
sufficient air is not provided through the circuit and exhaled air may be
rebreathed.
NOTE: If an alarm persists for no apparent reason, discontinue ventilator use
and contact Philips.
You can modify alarm settings at any time through the Alarm Settings tab.
9-1
Alarms, messages, and troubleshooting
Alarm LED
Active alarms
9-2
Alarms, messages, and troubleshooting
Alarm LED
on front Alarm message in Remote
Status panel Alarm status bar Alarms list Audio* Action required alarm
Low-priori- Off Yellow Yellow background Intermittent tone Respond promptly. Trouble-
ty alarm color. Alarm icon. at an interval of shoot as per Table 9-3.
approximately
20 seconds
High-prior- Flashes Alternates black Red background Repeating se- Respond immediately to On
ity alarm and red color. Alarm icon. quence of 5 tones ensure patient safety. Trou-
bleshoot as per Table 9-3.
High-prior- On contin- Vent Inoperative screen, including Primary alarm Continued safe ventilator
ity alarm – uously code (Figure 9-2) (Repeating se- operation may be in jeopar-
Vent Inop- quence of 5 dy. O2 flow and blower op-
erative tones) or backup eration are disabled.
alarm (alternating Immediately secure alter-
tone for a mini- native ventilation for the
mum of 2 min- patient. Troubleshoot as
utes) per Table 9-5.
* The volume of the primary alarm is the same for low- and high-priority alarms.
9-3
Alarms, messages, and troubleshooting
Setting alarm You can set the alarm loudness from the Menu window (see “Loudness” on
page 6-17).
loudness
9-4
Alarms, messages, and troubleshooting
Silencing alarms Silence an alarm for 2 minutes by selecting the Alarm Silence button.
The button icon is replaced by this one. A timer shows time remaining in the
2-minute alarm silence period.
Select Alarm Silence again at any time to reset the counter to 2:00 minutes.
During patient maneuvers, you can pre-silence audible alarms as desired.
Some alarms cannot be silenced; these are listed in Table 9-3. When a non-
silenceable alarm is annunciated, the following is shown.
Resetting alarms Most alarms reset themselves (autoreset) when the alarm triggering condition
is removed, but you must manually reset others. Table 9-3 specifies whether
an alarm is autoreset.
When an alarm is manually reset, the message is cleared from the Alarms list,
any other alarm indications are removed, and the alarm silence is terminated.
Autoreset alarms are shown with text crossed out in the Alarms list.
Clear the message from the Alarms list by selecting Alarm Reset.
9-5
Alarms, messages, and troubleshooting
Symptom-based To troubleshoot a problem with the ventilator, see Table 9-2. If an alarm
message is displayed, see also Table 9-3.
troubleshooting
Table 9-2: Symptom-based troubleshooting
Ventilation stops, but the ventilator has power. The ventilator Check the patient.
may be in standby or in the Vent Inoperative state. When the If the ventilator is in standby, reconnect the patient, and venti-
ventilator is in the Vent Inoperative state, continued safe venti- lation should resume.
lator operation may be in jeopardy. O2 flow and blower opera-
If the Alarm LED on the front panel is continuously lit, and/or
tion are disabled.
the Vent Inoperative screen is displayed, provide alternative
ventilation. Have the ventilator serviced. For details about the
specific Vent Inoperative alarm, see Table 9-5 on page 9-16.
The touchscreen is unresponsive or does not respond properly. Check the patient.
The ventilator continues to function at the selected settings. If the patient requires a setting change, provide alternative
Patient settings and patient data continue to be visible and ac- ventilation. Have the ventilator serviced.
curate, and alarms continue to be annunciated.
NOTE: If you cannot shut off the ventilator when the touch-
screen is unresponsive, press the ON/Shutdown key, then the
Accept (√) button on the top-right front of the ventilator.
The ventilator does not switch from battery to AC power. Check the patient.
Make sure the ventilator is connected to AC power. (If the ven-
tilator is connected to AC power and the ventilator is function-
ing correctly, the ON/Shutdown LED should be on.)
If problem persists, provide alternative ventilation. Have the
ventilator serviced.
The ventilator does not switch from AC power to battery. Check the patient.
A back-up alarm should annunciate. If problem persists, provide alternative ventilation. Have the
ventilator serviced.
The estimated exhaled tidal volume reading (VT) is inaccurate. Check the patient.
Check for large leaks.
Make sure ventilator and alarm settings are appropriate.
Make sure an approved patient circuit is in use.
Adjust the mask to ensure proper fit and adequate leak com-
pensation.
If the problem persists, provide alternative ventilation. Have
the ventilator serviced.
9-6
Alarms, messages, and troubleshooting
Alarms and other Table 9-3 is a list of alarms and other messages displayed by the ventilator,
along with descriptions, suggested corrective actions, and other information.
messages
The ID (identifier) listed with the priority type is the priority number of the
alarm. This priority number determines the order of alarm message display.
Unless otherwise indicated, alarms listed as autoresettable are reset when the
alarm condition is removed.
AVAPS: Target VT Ex- AVAPS target pressure is Check the patient. Con- Infor- No Yes N/A
ceeded. Min Pres- less than Min P setting. firm pressure settings are mation
sure Too High The ventilator limits its compatible with target. (63)
applied pressure to Min P. Evaluate pressure and vol-
ume settings.
AVAPS: Target VT Not AVAPS target pressure ex- Check the patient. Con- Infor- No Yes N/A
Achieved. Insuffi- ceeds Max P setting. The firm pressure settings are mation
cient Max Pressure ventilator limits applied compatible with target. (62)
pressure to Max P. Evaluate pressure and vol-
ume settings.
Bacteria filter must An inspiratory bacteria fil- Confirm that a bacteria fil- Infor- Yes N/A N/A
be installed onto gas ter must be installed on ter is installed. Install a mation
outlet the patient gas outlet port. bacteria filter if one is not (67)
present.
Cannot Reach Target Displays when HFT (high Check the patient. Check Low No Yes Yes
Flow flow therapy) is active. In- that the high flow nasal (53)
dicates that flow target is cannula size is appropri-
not achieved. ate for the flow setting.
Check that an occlusive
interface is NOT in use (a
cannula fully sealed with-
in the nares, an NIV mask
or direct connection to an
ETT/trach). Check for an
occlusion, kink or liquid in
the patient circuit.
High Inspiratory Pres- Measured inspiratory pres- Check the patient. Con- High Yes Yes Yes
sure sure is greater than the firm ventilator and alarm (45)
HIP setting, and the venti- settings are appropriate. If
lator cycles into exhala- problem persists, provide
tion. Autoresets after a alternative ventilation.
complete inspiration with- Have the ventilator ser-
out the alarm condition. viced.
High O2 Supply Pres- O2 inlet pressure is great- Check the patient. If prob- High No Yes Yes
sure er than 92 psig, so O2 en- lem persists, provide alter- (49)
richment ends. Autoresets native ventilation. Have
when O2 supply pressure the ventilator serviced.
falls below 87 psig.
9-7
Alarms, messages, and troubleshooting
Table 9-3: Alarm and other messages: summary and troubleshooting (continued)
High Rate Measured respiratory rate Check the patient. Con- Low/ Yes Yes Yes
is greater than the Hi Rate firm ventilator and alarm High
setting. Escalates to a settings are appropriate. If (59)
high-priority alarm if the problem persists, provide
alarm condition persists alternative ventilation.
for more than 60 sec. Have the ventilator ser-
viced.
High Tidal Volume Measured estimated tidal Check the patient. Check Low/ Yes Yes Yes
volume is greater than the for large leaks. Confirm High
Hi VT setting. Escalates to ventilator and alarm set- (58)
a high-priority alarm if the tings are appropriate. If
alarm condition persists problem persists, provide
for more than 60 sec. alternative ventilation.
Have the ventilator ser-
viced.
Low Inspiratory Pres- Measured inspiratory pres- Check the patient. Con- High Yes Yes Yes
sure sure is less than the LIP firm ventilator and alarm (46)
setting. settings are appropriate. If
problem persists, provide
alternative ventilation.
Have the ventilator ser-
viced.
Low Internal Battery Battery can provide oper- Connect ventilator to AC High No Yes No
ating power for only an ad- power. Provide alternative (43)
ditional 15 minutes under ventilation.
nominal conditions. Au-
toresets when ventilator is
connected to AC power.
Low Leak–CO2 Re- Estimated volume of ex- Check the patient, as pos- High Yes Yes Yes
breathing Risk haled gas returned to the sibility of CO2 rebreath- (42)
patient is high. ing could pose a potential
problem. Check the exha-
lation port for occlusions.
Check for appropriate pa-
tient interface and exhala-
tion port settings.
If the approved exhala-
tion port is unobstructed,
mask and port settings are
appropriate, and problem
persists, increase the ven-
tilator baseline flow by
adding leak or increasing
EPAP, if possible.
Switch to an approved
nebulizer.
9-8
Alarms, messages, and troubleshooting
Table 9-3: Alarm and other messages: summary and troubleshooting (continued)
Low Minute Ventila- Estimated minute ventila- Check the patient. Con- Low Yes Yes Yes
•
tion tion is less than the Lo V E firm ventilator and alarm (56)
setting. Escalates to a settings are appropriate. If
high-priority alarm if the problem persists, provide
alarm condition persists alternative ventilation.
for more than 60 sec. Have the ventilator ser-
viced.
Low O2 Supply Pres- O2 inlet pressure is less Check the patient. Attach High No Yes Yes
sure than 30 psig and deliv- to oxygen source with suf- (48)
ered O2 is at least 5% ficient pressure.
lower than O2 setting. The If problem persists, pro-
ventilator continues to de- vide alternative ventila-
liver as much O2 support tion. Have the ventilator
as possible, but it ends O2 serviced.
support when the O2 inlet
pressure drops to less
than 18 psig. Autoresets
when O2 inlet pressure ex-
ceeds 23 psig.
Low Rate A low-priority alarm if the Check the patient. Con- Low/ Yes Yes Yes
measured respiratory rate firm ventilator and alarm High
is less than the Lo Rate settings are appropriate. If (55)
setting, escalating to a problem persists, provide
high-priority alarm in 60 alternative ventilation.
sec. Have the ventilator ser-
A high-priority alarm from viced.
the start if:
• The Lo Rate setting is
4 BPM and there are no
breaths for > 60/Lo Rate
setting.
• The Lo Rate setting is >
4 BPM and there are no
breaths for > 15 sec.
Low Tidal Volume Estimated tidal volume is Check the patient. Con- Low Yes Yes Yes
less than the Lo VT set- firm ventilator and alarm (57)
ting. Escalates to a high- settings are appropriate. If
priority alarm if the alarm problem persists, provide
condition persists for alternative ventilation.
more than 60 sec. Have the ventilator ser-
viced.
Mask:x, Exh Port:y Displays when ventilator is Select mask and port from Infor- No Yes N/A
Use Menu to change turned on. Displays select- Menu tab. Message is re- mation
ed mask type and exhala- moved when user con- (64)
tion port. firms selections, or after 5
minutes.
9-9
Alarms, messages, and troubleshooting
Table 9-3: Alarm and other messages: summary and troubleshooting (continued)
Oxygen Not Available Oxygen supply pressure Check the patient. Check High No Yes Yes
out of range, oxygen de- if high/low O2 source is (47)
vice failed, air flow sensor the problem and correct.
and/or oxygen flow sensor If problem persists, pro-
calibration failed, or oxy- vide alternative ventila-
gen inlet pressure sensor tion. Have the ventilator
calibration failed. The serviced.
ventilator discontinues ox-
ygen support.
Patient alarms are Displays when HFT (high Manually reset to confirm Low/ Yes No Yes
disabled during HFT flow therapy) is active. Pa- and clear the audible Infor-
tient alarms are not avail- alarm. mation
able in this therapy. (54)
Patient Circuit Proximal pressure and pa- Check the patient. Check High Yes Yes Yes
Occluded tient flow are low. Patient the patient circuit for bulk (40)
circuit occluded. liquid, crimps, or blocked
filter. Confirm ventilator
and alarm settings are ap-
propriate. If problem per-
sists, provide alternative
ventilation. Have the ven-
tilator serviced.
Patient Circuit Oc- Displays when HFT (high Check the patient. Check High No Yes Yes
cluded flow therapy) is active. that an occlusive interface (52)
Gas flow to the patient is is NOT in use (a cannula
obstructed. fully sealed within the na-
res, an NIV mask or direct
connect to an ETT/trach).
Check for an occlusion,
kink or liquid in the pa-
tient circuit. If problem
persists, provide alterna-
tive ventilation.
Patient Disconnect Patient is no longer con- Check the patient. Recon- High Yes Yes Yes
nected to the ventilator, nect patient circuit. Con- (39)
either through circuit or firm ventilator and alarm
mask, or the patient cir- settings are appropriate. If
cuit is disconnected from problem persists, provide
the ventilator and the pa- alternative ventilation.
tient is no longer receiving Have the ventilator ser-
ventilatory support. Venti- viced.
lation continues.
NOTE: The Patient Dis-
connect alarm is trig-
gered when 11 seconds
have elapsed.
9-10
Alarms, messages, and troubleshooting
Table 9-3: Alarm and other messages: summary and troubleshooting (continued)
Power has been re- Power is restored follow- Check the patient. Con- Infor- Yes N/A N/A
stored ing loss of power. The ven- firm ventilator and alarm mation
tilator restarts and settings are appropriate. (66)
continues ventilation in
the mode set before power
was lost.
PPV Maximum Pres- Computed target pressure Check the patient. Con- Infor- Yes Yes Yes
sure is greater than the PPV firm ventilator and alarm mation/
maximum pressure alarm settings are appropriate. High
limit. Possible causes are Check for circuit or mask (51)
excessive patient inspira- leaks. If problem persists,
tory effort; a significant provide alternative ventila-
change in the leak around tion. Have the ventilator
the patient interface; or serviced.
high PPV %, Max E, or Max
R setting. Target pressure
is limited.
At first, an information
message. If condition per-
sists for three consecu-
tive PPV inspirations, this
escalates to a high-priority
alarm.
PPV Maximum Vol- Estimated delivered pa- Check the patient. Con- Infor- Yes Yes Yes
ume tient tidal volume is great- firm ventilator and alarm mation/
er than the PPV maximum settings are appropriate. High
volume alarm limit. Possi- Check for circuit or mask (50)
ble causes are excessive leaks. If problem persists,
patient inspiratory effort; provide alternative ventila-
a significant change in the tion. Have the ventilator
leak around the patient in- serviced.
terface; or high PPV %,
Max E, or Max R setting.
Ventilator cycles to exha-
lation.
At first, an information
message. If condition per-
sists for three consecu-
tive PPV inspirations, this
escalates to a high-priority
alarm.
Pressure Regulation Pressures exceed ventila- Check the patient. Con- High Yes Yes Yes
High tor-defined thresholds for firm ventilator and alarm (44)
IPAP, EPAP, or both. Ven- settings are appropriate. If
tilation continues. Autore- problem persists, provide
sets when alarm condition alternative ventilation.
removed; otherwise, tran- Have the ventilator ser-
sitions to the ventilator in- viced.
operative state if pressure
continues to rise.
9-11
Alarms, messages, and troubleshooting
Table 9-3: Alarm and other messages: summary and troubleshooting (continued)
Proximal Pressure Proximal pressure low for Check the patient. Recon- High Yes Yes Yes
Line Disconnect a few seconds. Proximal nect proximal pressure (41)
pressure line is discon- line. Confirm ventilator
nected. Air flow to the pa- and alarm settings are ap-
tient continues. propriate. If problem per-
sists, provide alternative
ventilation. Have the ven-
tilator serviced.
Running on Internal System is powered by the Connect ventilator to AC Low Yes Yes Yes
Battery internal battery. Autore- power. (60)
sets when ventilator is
connected to AC power.
Trigger:+x, Auto-Trak+ is active and Confirm that Auto-Trak+ Infor- Yes Yes N/A
E-Cycle: +x using the displayed set- settings are appropriate. mation
Use Menu to change tings. This messages is (65)
displayed for 5 min after
start-up.
Using Default Set- Displayed after power on Check the patient. Check Infor- Yes Yes N/A
tings if setting values are cor- and adjust settings as re- mation
rupted or not set, or if de- quired. (61)
fault values were restored
by the user.
Check Vent: 1.8 V Technical failure Check the patient. Provide High Yes No No
Supply Failed alternative ventilation. Have (21)
the ventilator serviced.
Check Vent: 3.3 V Technical failure Check the patient. Provide High Yes No No
Supply Failed alternative ventilation. Have (22)
the ventilator serviced.
Check Vent: 5 V Sup- Technical failure Check the patient. Provide High Yes No No
ply Failed alternative ventilation. Have (23)
the ventilator serviced.
Check Vent: 12 V Technical failure Check the patient. Provide High Yes No No
Supply Failed alternative ventilation. Have (24)
the ventilator serviced.
Check Vent: 24 V Technical failure Check the patient. Provide High Yes No No
Supply Failed alternative ventilation. Have (25)
the ventilator serviced.
9-12
Alarms, messages, and troubleshooting
Table 9-4: Check Vent alarm messages: summary and troubleshooting (continued)
Check Vent: 35 V Technical failure Check the patient. Provide High Yes No No
Supply Failed alternative ventilation. Have (26)
the ventilator serviced.
Check Vent: Air Flow Flow-related patient Check the patient. Provide High Yes No No
Sensor Calibration data is disabled. O2 alternative ventilation. Have (13)
Data Error concentration switches the ventilator serviced.
to 21% (ventilates with
air only). Default vol-
ume used in AVAPS
mode. Standby dis-
abled. Volume, leak,
disconnect, and occlu-
sion alarms compro-
mised.
Check Vent: Alarm Technical failure. Check the patient. Provide High Yes No No
LED Failed alternative ventilation. Have (6)
the ventilator serviced.
Check Vent: Aux Backup alarm problem Check the patient. Provide High Yes No No
Supply Failed alternative ventilation. Have (20)
the ventilator serviced.
Check Vent: Backup Backup alarm problem Check the patient. Provide High Yes No No
Alarm Failed alternative ventilation. Have (5)
the ventilator serviced.
Check Vent: Barome- Default barometric Check the patient. Provide High Yes No No
ter Calibration Data pressure of 686.0 alternative ventilation. Have (18)
Error mmHg (approximately the ventilator serviced.
900 m/2953 ft above
sea level) used in cal-
culations
Check Vent: Barome- Default barometric Check the patient. Provide High Yes No No
ter Sensor Range Er- pressure of 686.0 alternative ventilation. Have (19)
ror mmHg (approximately the ventilator serviced.
900 m/2953 ft above
sea level) used in cal-
culations
Check Vent: Battery Battery problem Check the patient. Connect High Yes No No
Failed the ventilator to AC. Provide (35)
alternative ventilation. Have
the ventilator serviced.
Check Vent: Battery Battery problem Check the patient. Connect High Yes No No
Temperature High the ventilator to AC. Check (34)
for causes of overheating,
such as high room tempera-
ture, blocked vents, clogged
air inlet filter, or nonfunc-
tional fan. Provide alterna-
tive ventilation. Have the
ventilator serviced.
9-13
Alarms, messages, and troubleshooting
Table 9-4: Check Vent alarm messages: summary and troubleshooting (continued)
Check Vent: Blower Technical failure Check the patient. Provide High Yes No No
Stalled alternative ventilation. Have (2)
the ventilator serviced.
Check Vent: Blower Technical failure Check the patient. Check for High Yes No No
Temperature High causes of overheating, such (33)
as high room temperature,
blocked vents, clogged air
inlet filter, or nonfunctional
fan. Provide alternative ven-
tilation. Have the ventilator
serviced.
Check Vent: Cooling Overheating of ventila- Check the patient. Provide High Yes No No
Fan Speed Error tor possible alternative ventilation. Have (36)
the ventilator serviced.
Check Vent: CPU Technical failure Check the patient. Provide High Yes No No
PCBA ADC Failed alternative ventilation. Have (29)
the ventilator serviced.
Check Vent: Data Ac- Technical failure Check the patient. Provide High Yes No No
quisition PCBA ADC alternative ventilation. Have (27)
Failed the ventilator serviced.
Check Vent: Flash Technical failure Check the patient. Provide High Yes No No
File System Error alternative ventilation. Have (37)
the ventilator serviced.
Check Vent: Internal Technical failure Check the patient. Check for High Yes No No
Temperature High causes of overheating, such (30)
CPU as high room temperature,
blocked vents, clogged air
inlet filter, or nonfunctional
fan. Provide alternative ven-
tilation. Have the ventilator
serviced.
Check Vent: Internal Technical failure Check the patient. Check for High Yes No No
Temperature High causes of overheating, such (31)
Daq as high room temperature,
blocked vents, clogged air
inlet filter, or nonfunctional
fan. Provide alternative ven-
tilation. Have the ventilator
serviced.
Check Vent: Internal Technical failure Check the patient. Provide High Yes No No
Temperature High alternative ventilation. Have (32)
Mtr the ventilator serviced.
Check Vent: Ma- Proximal pressure is Check the patient. Provide High Yes No No
chine Pressure Sen- not measured. Pres- alternative ventilation. Have (9)
sor Auto-Zero Failed sure-related alarms are the ventilator serviced.
compromised.
9-14
Alarms, messages, and troubleshooting
Table 9-4: Check Vent alarm messages: summary and troubleshooting (continued)
Check Vent: Ma- Proximal pressure is Check the patient. Provide High Yes No No
chine Pressure Sen- not measured. Pres- alternative ventilation. Have (7)
sor Calibration Data sure-related alarms are the ventilator serviced.
Error compromised.
Check Vent: Ma- Proximal pressure is Check the patient. Provide High Yes No No
chine Pressure Sen- not measured. Pres- alternative ventilation. Have (11)
sor Range Error sure-related alarms are the ventilator serviced.
compromised.
Check Vent: Motor Technical failure Check the patient. Provide High Yes No No
Control PCBA ADC alternative ventilation. Have (28)
Failed the ventilator serviced.
Check Vent: O2 Flow Continues to ventilate Check the patient. Provide High Yes No No
Sensor Calibration with air only alternative ventilation. Have (14)
Data Error the ventilator serviced.
Check Vent: O2 Pres- Continues to ventilate Check the patient. Provide High Yes No No
sure Sensor Calibra- with air only alternative ventilation. Have (15)
tion Data Error the ventilator serviced.
Check Vent: O2 Sup- Continues to ventilate Check the patient. Provide High Yes No No
ply Pressure Sensor with air only alternative ventilation. Have (17)
Range Error the ventilator serviced.
Check Vent: OVP Technical failure Check the patient. Provide High Yes No No
Circuit Failed alternative ventilation. Have (38)
the ventilator serviced.
Check Vent: Oxygen Continues to ventilate Check the patient. Provide High Yes No No
Device Failed with air only alternative ventilation. Have (16)
the ventilator serviced.
Check Vent: Primary Technical failure Check the patient. Provide High Yes No No
Alarm Failed alternative ventilation. Have (4)
the ventilator serviced.
Check Vent: Pro- Technical failure Check the patient. Provide High Yes No No
gram CRC Test Failed alternative ventilation. Have (1)
the ventilator serviced.
Check Vent: Proximal Proximal pressure is Check the patient. Provide High Yes No No
Pressure Sensor not measured. Pres- alternative ventilation. Have (10)
Auto-Zero Failed sure-related alarms are the ventilator serviced.
compromised.
Check Vent: Proximal Proximal pressure is Check the patient. Provide High Yes No No
Pressure Sensor Cali- not measured. Pres- alternative ventilation. Have (8)
bration Data Error sure-related alarms are the ventilator serviced.
compromised.
9-15
Alarms, messages, and troubleshooting
Table 9-4: Check Vent alarm messages: summary and troubleshooting (continued)
Check Vent: Proximal Proximal pressure is Check the patient. Provide High Yes No No
Pressure Sensor not measured. Pres- alternative ventilation. Have (12)
Range Error sure-related alarms are the ventilator serviced.
compromised. When using a high flow na-
Also displays when sal cannula with FEP Con-
HFT (high flow therapy) nect, the proximal pressure
is active and proximal line should be disconnected
pressure is out of from the ventilator port
range. during HFT. If this message
is seen when switching the
patient from ventilation to
HFT, check to make sure the
proximal pressure line is dis-
connected.
Check Vent: Ventila- Technical failure Check the patient. Provide High Yes No No
tor Restarted alternative ventilation. Have (3)
the ventilator serviced.
Vent Inoperative Technical failure. The Check the patient. Provide al- High No No No
1000 ventilator is in the ven- ternative ventilation. Have the (2)
3.3 V Supply tilator inoperative ventilator serviced.
Failed state.
Vent Inoperative Technical failure. The Check the patient. Provide al- High No No No
1001 ventilator is in the ven- ternative ventilation. Have the (3)
12 V Supply tilator inoperative ventilator serviced.
Failed state.
Vent Inoperative Technical failure. The Check the patient. Provide al- High No No No
1002 ventilator is in the ven- ternative ventilation. Have the (4)
Blower Tempera- tilator inoperative ventilator serviced.
ture Too High state.
Vent Inoperative Technical failure of the Check the patient. Provide al- High No No No
1003 CPU PCBA. The venti- ternative ventilation. Have the (5)
Internal Tempera- lator is in the ventilator ventilator serviced.
ture High inoperative state.
Vent Inoperative Technical failure of the Check the patient. Provide al- High No No No
1004 DAQ PCBA. The venti- ternative ventilation. Have the (6)
Internal Tempera- lator is in the ventilator ventilator serviced.
ture High inoperative state.
9-16
Alarms, messages, and troubleshooting
Table 9-5: Vent Inoperative alarm messages: summary and troubleshooting (continued)
Vent Inoperative Technical failure of the Check the patient. Provide al- High No No No
1005 motor PCBA. The venti- ternative ventilation. Have the (7)
Internal Tempera- lator is in the ventilator ventilator serviced.
ture High inoperative state.
Vent Inoperative Technical failure. The Check the patient. Provide al- High No No No
1006 ventilator is in the ven- ternative ventilation. Have the (8)
Data Acquisition tilator inoperative ventilator serviced.
PCBA ADC Failed state.
Vent Inoperative Technical failure. The Check the patient. Provide al- High No No No
1007 ventilator is in the ven- ternative ventilation. Have the (9)
Machine and tilator inoperative ventilator serviced.
Proximal Pres- state.
sure Sensors
Failed
Vent Inoperative Technical failure. The Check the patient. Provide al- High No No No
1008 ventilator is in the ven- ternative ventilation. Have the (10)
Machine and tilator inoperative ventilator serviced.
Proximal Pres- state.
sure Sensors
Failed
Vent Inoperative Technical failure. The Check the patient. Provide al- High No No No
1009 ventilator is in the ven- ternative ventilation. Have the (11)
Pressure Regula- tilator inoperative ventilator serviced.
tion High state.
Vent Inoperative Technical failure. The Check the patient. Provide al- High No No No
100A ventilator is in the ven- ternative ventilation. Have the (12)
Data Acquisition tilator inoperative ventilator serviced.
PCBA ADC Refer- state.
ence Failed
Vent Inoperative Technical failure. The Check the patient. Provide al- High No No No
100B ventilator is in the ven- ternative ventilation. Have the (13)
Watchdog Test tilator inoperative ventilator serviced.
Failed state.
9-17
Alarms, messages, and troubleshooting
9-18
Chapter 10. Care and maintenance
WARNING: To reduce the risk of electric shock, power down the ventilator and
disconnect it from AC power before cleaning, disinfecting, or servicing it.
WARNING: This product consists of devices that may contain mercury, which must be
recycled or disposed of in accordance with local, state, or federal laws.
(Within this system, the backlight lamps in the monitor display contain
mercury.)
WARNING: Before performing maintenance procedures, disconnect the ventilator from the
patient, shut it down, and disconnect it from AC power. All operator
maintenance must be performed with the patient off the ventilator. Failure to do
so can result in electric shock to the patient and operator.
NOTE: It is the user’s responsibility to comply with the information provided
in this chapter.
NOTE: Cleaning and disinfection are most effective if soiling is not allowed
to dry on a medical device.1
NOTE: Disinfection is most effective on medical devices that were previously
cleaned.1
NOTE: For all V60/V60 Plus hardware accessories recommended by Philips,
follow the cleaning and disinfection guidelines in this chapter. For
multi-patient interface and circuit accessories, consult the product
instructions for use. For single patient use accessories, no cleaning
and disinfection is needed.
To ensure the safety and reliability of your ventilator, follow these maintenance
procedures along with your own institutional policies for cleaning, disinfecting,
and maintaining equipment. All the procedures in this manual are intended to
be performed by the operator. For further maintenance, contact your service
representative.
10-1
Care and maintenance
Exterior and CAUTION: To prevent possible damage to the ventilator, use only those cleaning
and disinfecting agents listed in this manual.
touchscreen cleaning
CAUTION: To prevent possible damage to the ventilator, do not drip or spray any
liquids directly onto any surface including the front panel,
touchscreen, navigation ring (legacy versions), and Accept button.
CAUTION: Never clean or disinfect the touchscreen with an abrasive brush or
device, since this will cause irreparable damage.
CAUTION: Do not attempt to sterilize or autoclave the ventilator.
NOTE: Use of unapproved cleaning and disinfecting agents may cause
damage to the enclosure, touchscreen, or parts of the ventilator.
Cleaning instructions
2. Wipe cleaning agent over the entire exterior surface and touchscreen
of the ventilator.
10-2
Care and maintenance
Exterior and CAUTION: To prevent possible damage to the ventilator, use only those cleaning
and disinfecting agents listed in this manual.
touchscreen
CAUTION: To prevent possible damage to the ventilator, do not drip or spray any
disinfection liquids directly onto any surface including the front panel,
touchscreen, navigation ring (legacy versions), and Accept button.
CAUTION: Never clean or disinfect the touchscreen with an abrasive brush or
device, since this will cause irreparable damage.
CAUTION: Do not attempt to sterilize or autoclave the ventilator.
NOTE: Use of unapproved cleaning and disinfecting agents may cause
damage to the enclosure, touchscreen, or parts of the ventilator.
The following disinfecting agents are acceptable for use on the touchscreen
and exterior surfaces of the ventilator:
Disinfectant
3% hydrogen peroxide
Disinfection instructions
1. Ensure that cleaning was done per the procedure in “Exterior and
touchscreen cleaning” on page 10-2.
5. Rinse with a clean cloth dampened with water and allow to dry
completely before reuse.
10-3
Care and maintenance
Bacteria filter, patient Follow the manufacturer’s instructions that accompany the accessory.
circuit, and other
accessories WARNING: To prevent patient or ventilator contamination, inspect and replace the
main flow bacteria filter between patients and at regular intervals (or as
stated by the manufacturer).
WARNING: To prevent possible patient injury, inspect and verify the proper operation
of the exhalation port regularly during use.
CAUTION: Because some environments cause a quicker collection of lint and
dust than others, inspect the filters more often when needed. The air
inlet filter should be replaced; the cooling fan filter should be
cleaned.
CAUTION: To ensure proper system performance, use a Respironics-approved air
inlet filter.
10-4
Care and maintenance
Preventive WARNING: Only authorized service personnel should replace parts within the
ventilator or perform other service activities. Unauthorized personnel
maintenance without proper training are at risk of electric shock.
WARNING: Turn off the ventilator and disconnect it from the AC mains outlet before
you perform decontamination or maintenance procedures. Failure to do so
may result in electric shock.
The expected service life of your V60/V60 Plus ventilator is 10 years. Perform
preventive maintenance on the ventilator according to the schedule in
Table 10-2. You can view the hours of ventilator operation in the Vent Info
window (“Vent Info (ventilator information)” on page 6-18). The following
subsections provide details for some of these preventive maintenance
procedures.
Every month Cooling fan filter Inspect for occlusions, dust, lint, etc. If discol-
ored or dirty, remove and wash or rinse thor-
oughly, and let dry completely before
reinstalling.
* Must be done by authorized service personnel according to the instructions in the service
manual.
10-5
Care and maintenance
Replacing the air inlet filter
Replace the air inlet filter as follows, referring to Figure 10-1.
3. Remove the inlet filter by pinching it out of the recess in the bracket.
4. Install a new air filter by tucking it into the recessed area. Replace the
side panel, and push in and turn the D-ring fastener one-quarter turn
until it locks.
Captive
fastener
10-6
Care and maintenance
1. Insert a small, flat blade driver tip between the foam filter and the
filter retaining cover (Figure 10-2).
2. Gently pry the filter cover from the back of the ventilator. Do not
remove the fan retaining pins.
4. Replace the filter, then snap the filter cover into place.
Foam filter
10-7
Care and maintenance
Disposal WARNING: This product consists of devices that may contain mercury, which must be
recycled or disposed of in accordance with local, state, or federal laws.
(Within this system, the backlight lamps in the monitor display contain
mercury.)
Dispose of all parts removed from the device according to your institution’s
protocol. Follow all local, state, and federal regulations with respect to
environmental protection, especially when disposing of the electronic device or
parts of it (for example, oxygen cell, batteries).
This device contains a lithium ion battery that cannot be recycled. Please
contact customer service for safe disposal instructions of this part.
Storage between Follow the steps below when storing the ventilator between patient use:
patient use 1. Ensure that the patient circuit is assembled and installed properly as
described in “Installing the patient circuit” on page 5-3.
2. Plug the ventilator into an AC outlet and verify that the power source
symbol is displayed.
10-8
Care and maintenance
Service and repairs For technical service or repair information not included in this chapter, contact
Philips.
Repacking and CAUTION: To prevent possible damage to the ventilator, always ship it with the
original packing material. If the original material is not available,
shipping contact Philips to order replacements.
NOTE: Transport of lithium ion batteries is strictly controlled by international
regulations and laws. Do not ship the battery either in the ventilator or
separately by sea or air.
Remove the battery from the ventilator before shipping the ventilator. See
“Installing the battery” on page A-4 for more information. Ship the battery and
ventilator separately in appropriate packaging in conformance with federal,
state, and local regulations.
If necessary, Philips will send you a battery return kit that contains a prepaid
postal label and instructions for returning the battery if it has failed
prematurely (within 5 years of its manufacture date). The order number for the
return kit is 989805663471 / part number 1146145.
10-9
Care and maintenance
10-10
Chapter 11. Technical specifications
Control settings Table 11-1 lists ventilator control setting ranges, resolutions, and accuracies.
Table 11-2 lists the controls active in the different ventilation modes.
Mode settings
Control settings
I-Time (Inspiratory 0.30 to 3.00 sec 0.05 sec ± 0.03 sec 1.00 sec
Time)
11-1
Technical specifications
I-Time I-Time*
O2 O2
Volume VT Max V
Max E
Max R
11-2
Technical specifications
Patient data
Table 11-3: Patient data ranges, resolutions, and accuracies during ventilation
Breath phase/trigger indicator Spont, Timed, Exhale Color-coded display: Spont - N/A
turquoise, Timed - orange, Ex-
hale - blue
TI/TTOT 0% to 91% 1% ± 5%
Waveform window
11-3
Technical specifications
Alarms Table 11-4 lists the adjustable alarm ranges and resolutions. Table 9-3 on
page 9-7 describes other, nonadjustable alarms.
Menu window
settings Table 11-5: Menu window settings and ranges
Parameter Range
Brightness 1 to 5
Loudness 1 to 10
11-4
Technical specifications
Diagnostic mode
Table 11-6: Diagnostic mode functions
functions
Function Range
Date/Time --
Software Options --
11-5
Technical specifications
Physical
characteristics Table 11-7: Physical characteristics
Parameter Specification
Dimensions
(33.7 cm)
13.3 in.
Environmental
specifications Table 11-8: Environmental specifications
Parameter Specification
11-6
Technical specifications
Pneumatic
specifications Table 11-9: Pneumatic specifications
Parameter Specification
Connector: SIS
Pressure: 3.31 to 6.00 bar / 331 to 600 kPa / 48 to
87 psig
Flow: 175 SLPM
Connector: SIS
Pressure: 3.66 to 6.00 bar / 366 to 600 kPa / 53 to
87 psig
Flow: 175 SLPM
11-7
Technical specifications
Electrical
specifications Table 11-10: Electrical specifications
Parameter Specification
AC frequency 50/60 Hz
AC power 300 VA
Accessory NOTE: Any part that is added to the patient circuit changes the compliance
and resistance of the ventilator breathing system. To achieve the
requirements ventilator performance specified in this manual, the ventilator
breathing system must meet the specifications listed in Table 11-11.
Parameter Specification
11-8
Technical specifications
Alarm-related
specifications Table 11-12: Alarm-related specifications
Parameter Specification
Delay time from the onset of the < 10 ms from onset of the alarm condition to the
alarm condition to the point that transmission of the signal
the representation of the alarm < 500 s until alarms received from the ventilator are
condition leaves the signal out- displayed on the IntelliVue patient monitor. This de-
put port lay is in addition to the alarm detection and process-
ing delays of the external device.
Remote alarm delay time The time it takes the message to appear on the re-
mote alarm depends on the characteristics of the de-
vice.
Maximum time from the alarm All alarms except those listed below: < 10 s
condition triggering event to the • Patient disconnect alarm: 11 s
generation of an alarm signal
• Proximal pressure line disconnect alarm: 15 s
• Low Inspiratory Pressure (LIP) alarm:
user-configurable from 5 to 60 s
• Check vent: Blower temperature high: 10 minutes
Mean delay, or the sum of mean All alarms except those listed below: < 5 s
delays, from the triggering event • Cooling fan failure alarm: 10 s
to the generation of an alarm sig-
nal • Blower temperature alarm: 10 s
• ADC wraparound: 6 s
Audio alarm loudness* Highest volume setting: Average sound pressure level
is approximately 76 dB(A)
Lowest volume setting: Average sound pressure level
is approximately 62 dB(A)
High-priority auditory alarm sig- Average sound power level is approximately 54 dB(A)
nal sound pressure level range, measured at the ventilator
measured per Average sound pressure level is approximately 46
ISO 3744:2010 ANSI/ dB(A) measured 1 m from the ventilator
Other specifications
Table 11-13: Other specifications
Parameter/Characteristic Specification
11-9
Technical specifications
Parameter/Characteristic Specification
Triggering, cycling, and leak tol- As per the Digital Auto-Trak Sensitivity algorithms (see
erance “Auto-Trak Sensitivity” on page 4-3)
Maximum time required for the The ventilator adjusts O2 within one breath.
O2 concentration in the deliv- FiO2 within the gas delivery system and entire breath-
ered volume to change from a ing circuit adjusts at the following rate:
volume fraction of 21% to 90%
Up to 18 seconds for delivered volume of 500 mL
using the worst-case ventilator
breathing system or using the Up to 17 seconds for delivered volume of 200 mL
maximum internal volume venti-
lator breathing system.
Operational acoustics* Average noise level is less than 45 dB(A) when mea-
ISO/FDIS 80601-2-12:2010 sured 1 m from the ventilator
201.9.6.2.1.101
11-10
Appendix A. First-time installation
Before putting the ventilator into service for the first time, install it as
described in this chapter.
Unpacking and Unpack the ventilator and inspect it for damage. Inspect the exterior cabinet of
the ventilator for cracks, scratches, or blemishes. Inspect the front panel for
inspection scratches or abrasions. Correct and/or report any problems found to Philips
before using the ventilator.
Before using the ventilator the first time, we recommend wiping the exterior
clean and disinfecting components according to the instructions in Chapter 10.
A-1
First-time installation
Mounting the CAUTION: To prevent possible damage to the ventilator, always secure it to its
stand or securely place it on a flat, stable surface that is free of dirt
ventilator and debris. Do not use the ventilator adjacent to, or stack it with,
other equipment.
NOTE: If you mount the ventilator to a stand, make sure the stand is
approved by Philips.
Align the ventilator above the stand as shown in Figure A-1. Make sure the four
feet at the base of the ventilator are aligned to slide into the grooves at the top
of the stand. Ensure that the locking lever on the back right of the stand locks
into place.
A-2
First-time installation
Figure A-2 shows the installed ventilator. Use the brakes to lock and unlock
the wheels as needed. Make sure the wheels are unlocked before moving the
ventilator.
Power cords
can be stored
on stand hooks
Wheel lock
A-3
First-time installation
Installing the battery WARNING: Installation or replacement of lithium batteries by inadequately trained
personnel could result in a hazard.
WARNING: To reduce the risk of fire, explosion, leakage, or other hazard, take these
precautions with respect to the battery:
- Do not attempt to disassemble, open, drop, crush, bend or deform,
insert foreign objects into, puncture, or shred the battery pack; modify
or remanufacture it; immerse or expose it to water or other liquids;
expose it to fire, excessive heat (including soldering irons); or put it in
a microwave oven.
- Replace the battery only with another battery specified by the
manufacturer.
- Follow all instructions for proper use of the battery.
- Do not short-circuit the battery or allow metallic or conductive objects
to contact the battery connector housing.
- Use the battery with the Respironics V60/V60 Plus Ventilator only.
NOTE: Failure to properly shut down the ventilator before battery installation
may result in erroneous alarms after power-on.
2. Remove the side panel by turning the captive fastener a ¼ turn and
releasing.
4. Holding the battery so that the vent hole faces up and the Philips logo
faces out, thread the battery cable through the battery bracket.
Position and place the battery inside the battery compartment.
Pinching the end of the battery connector, plug it in so that it locks in
place.
5. Reinstall the battery bracket by replacing the two screws. Reinstall the
side panel and secure the fastener with a ¼ turn clockwise.
A-4
First-time installation
A-5
First-time installation
Captive fastener
Bracket
Battery
Orient with vent hole on top
and Philips logo facing out
Battery
cable
A-6
First-time installation
Installing oxygen The Respironics V60/V60 Plus Ventilator destined for Japan, China, and the
USA are typically pre-configured. V60/V60 Plus Ventilators shipped to other
inlet connector and
countries may require installation of the power cord and oxygen inlet
AC power cord connector.
Oxygen
inlet
connector
Retaining plate
A-7
First-time installation
WARNING: To prevent unintentional disconnection of the power cord, always use the
correct, Philips-supplied power cord and lock it into place with the power
cord retainer before you switch the ventilator on. The retainer is designed
to hold the connector end of the Philips-supplied cord securely in place.
WARNING: The V60/V60 Plus Ventilator should not be positioned in a way that makes
it difficult to disconnect from mains power if necessary. Disconnect from
supply mains by removing the power cord from the wall outlet. The AC
mains plug is used as disconnection device.
2. Secure the power cord with the power cord retainer (Figure A-5):
a. Remove the power cord retainer by removing two screws.
b. Connect the power cord that is appropriate to your region into the
AC power connector.
c. Reinstall the power cord retainer over the power cord, and tighten
the screws with a 3.0-mm hex wrench.
Power cord
retainer
A-8
First-time installation
Installing the oxygen If desired, install the oxygen manifold kit as described in the accompanying
instructions.
manifold kit
Verifying ventilator Perform the following steps to verify ventilator and audible alarm operation:
operation and audible 1. Assemble and install a patient circuit. (See Chapter 5 for instructions
alarm on installing a patient circuit.)
2. Power on the ventilator and verify that it completes the power-on self-
test.
4. Reconnect the proximal pressure line, and manually reset the alarm.
Configuration and After completing the setup activities described in Chapter 5, set or check the
ventilator settings for language, units of measure, and time in the diagnostic
screen calibration mode (see Appendix E). Calibrate the screen as required, referring to
Appendix E
A-9
First-time installation
A-10
Appendix B. Communications interface
WARNING: Connect to the ventilator only items that are specified as part of or
compatible with the ventilator system. Additional equipment connected to
medical electrical equipment must comply with the respective IEC or ISO
standards. Furthermore, all configurations shall comply with the
requirements for medical electrical systems (see IEC 60601-1-1 or
clause 16 of edition 3 of IEC 60601-1, respectively). Anybody connecting
additional equipment to medical electrical equipment configures a
medical system and is therefore responsible for ensuring that the system
complies with the requirements for medical electrical systems. Also be
aware that local laws may take priority over the above mentioned
requirements. If in doubt, consult Philips.
WARNING: The USB port is not currently available for use. DO NOT connect or attempt
to power any equipment from the USB port.
WARNING: It is the responsibility of the end user to validate the compatibility and use
of information transmitted from the ventilator to the device to be
connected to the ventilator.
WARNING: The data provided through the communications interface is for reference
only. Decisions for patient care should be based on the clinician’s
observations of the patient.
B-1
Communications interface
RS-232 serial port The 25-pin D-sub RS-232 connector on the rear panel permits the ventilator to
export parameters to a patient monitor or a hospital information system.
Using Philips Using Philips monitors and the IntelliBridge or VueLink Open Interfaces
IntelliBridge or
VueLink NOTE: Data displayed on the IntelliBridge or VueLink systems is for
reference purposes only. Decisions for patient care should not be
based solely on the data obtained through the IntelliBridge system.
B-2
Communications interface
Data display
The data from your Respironics V60/V60 Plus Ventilator is displayed in several
windows on your Philips monitor. This data may be labeled differently on the
monitor than on the ventilator. Refer to Table B-1 to interpret these labels.
Waveform
AWF
VE (flow)
AWV V (volume)
Monitored parameters
MINVOL
VE
PIP PIP
RRaw Rate
Tin/Tt TI/TTOT
TVexp VT
B-3
Communications interface
Modes
STNDBY Standby
Control settings
sEppv Max E
PAVsup PPV %
sCPAP CPAP
sEPAP EPAP
sFIO2 O2
sIPAP IPAP
sRppv Max R
Alarm messages
B-4
Communications interface
Remote alarm port WARNING: To prevent possible patient injury due to nonannunciating alarms, verify
the operation of any remote alarm device before use.
WARNING: To ensure the functionality of the remote alarm, connect only Respironics-
approved cables to the remote alarm port.
CAUTION: The remote alarm port is intended to connect only to an SELV (safety
extra-low voltage and ungrounded system with basic insulation to
ground), in accordance with IEC 60601-1. To prevent damage to the
remote alarm, make sure the signal input does not exceed the
maximum rating of 24 VAC or 36 VDC at 500 mA with a minimum
current of 1 mA.
NOTE: Selecting Alarm Silence deactivates the remote alarm.
The remote alarm (nurse call) port allows ventilator alarm conditions to be
annunciated at locations away from the ventilator (for example, when the
ventilator is in an isolation room). The ventilator sends alarm signals to a
remote alarm through the connector at the rear of the ventilator (Figure B-1 on
page B-1). Figure B-4 shows the pin assignments for this connector. The
connector is a standard ¼-inch, female, audio (ring, tip, sleeve) connector.
The ventilator signals an alarm using either a normally open (NO) or normally
closed (NC) relay contact. The de-energized state of the relay represents an
B-5
Communications interface
alarm state (any high-priority alarm) and the energized state represents a non-
alarm state.This application requires one of the cables listed in Table B-2.
NC Tip
Common Sleeve
Remote alarm cable kit, Use on Normally Closed nurse call systems (system expects to see 1003741
alarm state = open open contacts when ventilator alarms). For ¼” jack.
Remote alarm cable kit, Use on Normally Opened nurse call systems (system expects to 1003742
alarm state = closed see closed contacts when ventilator alarms). For ¼” jack.
B-6
Appendix C. Parts and accessories
This appendix lists parts and accessories supplied by Philips that are
compatible with the Respironics V60/V60 Plus Ventilator. All parts and
accessories are not available in all markets.
WARNING: Avoid adding resistive circuit components on the patient side of the
proximal pressure line. Such components may defeat the disconnect alarm.
NOTE: Resistive components can include but are not limited to HMEs,
proximal flow sensors, a filter at the patient connection, or a narrow
diameter circuit attached to a mask.
NOTE: To ensure the correct performance of the ventilator and the accuracy
of patient data, we recommend you use only Respironics-approved
accessories with the ventilator.
For the most current list of approved accessories plus comprehensive ordering
information for compatible parts available from Philips, contact your Philips
representative or refer to the V60/V60 Plus ordering and accessories guide
(downloadable from philips.com/ifu or philips.com/hrcmanuals).
C-1
Parts and accessories
Patient Interfaces NOTE: Pediatric masks intended for patients weighing less than 20 kg (44
lb) are not approved for use with the V60/V60 Plus Ventilator.
Ventilation interfaces
Description Type
Respironics AP111
Respironics AF531
HFT interfaces
For use with V60 Plus ventilators and V60 ventilators that have 3.00 software
(or higher) and the HFT option installed.
Description
Respironics AC611 high flow nasal cannula with filtered exhalation port (FEP) connector
O2 analyzer/monitor
Description Part number Order number
C-2
Parts and accessories
Patient breathing
circuits
Description Quantity Part number Order number
Patient circuit, single-limb, heated, proximal pressure line, single- 10 1020523 989805610851
use, adult (Fisher & Paykel RT139).
Patient circuit, single-limb, heated, filtered exhalation port (FEP), 10 1122059 989805653191
humidifier chamber, proximal pressure line, single-use, 22-mm ID,
WILAmed (Not available in North America)
Patient circuit, single-limb, heated, filtered exhalation port (FEP), 10 1135739 989805658961
humidifier chamber, proximal pressure line, single-use, 22-mm ID,
Fisher & Paykel RT239
Patient circuit, single-limb, non-heated, filtered exhalation port 10 1065830 (with 989805621311
(FEP), proximal pressure line, single-use, 22-mm ID inspiratory and
exhalation port
filters)
1069210 (with no
filters) 989805634871
Humidifiers
Humidifiers
Respiratory humidifier, Fisher & Paykel MR850 --- --- Refer to the V60
ordering and
Respiratory humidifier, WILAmed AIRcon Gen2, 230V --- --- accessories guide
(Not available in North America)
Chambers
C-3
Parts and accessories
Bacteria filters
Description Quantity Part number Order number
Nebulizers
Description Quantity Part number Order number
Aerogen Solo nebulizer (for inline applications) --- --- Refer to the V60
ordering and
accessories guide
Operator
maintenance parts
Description Quantity Part number Order number
C-4
Appendix D. Regulatory compliance
Electromagnetic
compatibility (EMC) IEC 60601-1-2; Medical electrical equipment - Part 1-2: General requirements for
2014, Ed. 4.0 basic safety and essential performance - Collateral Standard: Elec-
tromagnetic disturbances
D-1
Regulatory compliance
Electromagnetic emissions
The V60/V60 Plus Ventilator is intended for use in the electromagnetic environment specified
below. The user of the V60/V60 Plus Ventilator should assure that it is used in such an envi-
ronment.
RF Emissions CIS- Group 1 The V60/V60 Plus Ventilator uses RF energy only for its
PR 11 internal function. Therefore, its RF emissions are very
low and are not likely to cause interference in nearby
electronic equipment.
RF Emissions CIS- Class A The V60/V60 Plus Ventilator is suitable for use in all es-
PR 11 tablishments, except for those that are domestic or di-
rectly connected to the public low voltage power supply
Harmonic emis- Class A network that supplies buildings used for domestic pur-
sions poses.
IEC 61000-3-2
D-2
Regulatory compliance
Electromagnetic immunity
The V60/V60 Plus Ventilator is intended for use in the electromagnetic environment specified below.
The user of the V60/V60 Plus Ventilator should assure that it is used in such an environment.
Electrical fast tran- ±2 kV for power sup- ±2 kV for power sup- Mains power quality should be
sient/burst ply lines. ply lines. that of a typical hospital environ-
IEC 61000-4-4 ±1 kV for input / out- ±1 kV for input / out- ment.
put lines put lines
Voltage dips, short 0% UT for 0.5 cycles 0% UT for 0.5 cycles Mains power quality should be
interruptions and 0% UT for 1.0 cycle 0% UT for 1.0 cycle that of a typical hospital environ-
voltage variations ment. If the user of the V60/V60
70% UT for 25 cycles 70% UT for 25 cycles
on power supply in- Plus Ventilator requires continued
(50 Hz)/ (50 Hz)/
put lines operation during power mains in-
30 cycles (60 Hz) 30 cycles (60 Hz)
IEC 61000-4-11 terruptions, it is recommended
0% UT for 250 cycles 0% UT for 250 cycles that the V60/V60 Plus Ventilator
(50 Hz)/ (50 Hz)/ be powered from an uninterrupt-
300 cycles (60 Hz) 300 cycles (60 Hz) ible power supply or a battery.
D-3
Regulatory compliance
12
d = ------- P
6 Vrms 6 Vrms V2 where V2 = 6 Vrms
150 kHz to 80 MHz
in ISM bandsa
12
d = ------- P
3 V/m e
3 V/m E1 80 MHz to 800 MHz, where E1 = 3 V/m
Radiated RF
IEC 61000-4-3 80 MHz to 2.7 GHz
380 MHz to 390 MHz 27 V/m
23
430 MHz to 470 MHz 28 V/m d = ------- P
E1 800 MHz to 2.7 GHz, where E1 = 3 V/m
704 MHz to 787 MHz 9 V/m
800 MHz to 960 MHz 28 V/m
1.700 GHz to 1.990 GHz 28 V/m where P is the maximum output power rating of the transmitter in
2.400 GHz to 2.570 GHz 28 V/m watts (W) according to the transmitter manufacturer and d is the
5.100 GHz to 5.800 GHz 9 V/m recommended separation distance in meters (m).b
Field strengths from fixed RF transmitters, as determined by an
electromagnetic site survey,c should be less than the compliance
level in each frequency range.d
NOTE 1: At 80 MHz and 800 MHz, the higher frequency range applies.
NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection
from structures, objects and people.
a. The ISM (industrial, scientific and medical) bands between 150 kHz and 80 MHz are 6.765 MHz to 6.795 MHz; 13.553 MHz to
13.567 MHz; 26.957 MHz to 27.283 MHz; and 40.66 MHz to 40.70 MHz.
b. The compliance levels in the ISM frequency bands between 150 kHz and 80 MHz and in the frequency range 80 MHz to 2.7 GHz are
intended to decrease the likelihood that mobile/ portable communications equipment could cause interference if it is inadvertently
brought into patient areas. For this reason, an additional factor of 10/3 has been incorporated into the formulae used in calculating the
recommended separation distance for transmitters in these frequency ranges.
c. Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radios, amateur
radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic
environment due to fixed RF transmitters, an electromagnetic site survey should be considered. If the measured field strength in the
location in which the V60/V60 Plus Ventilator is used exceeds the applicable RF compliance level above, the V60/V60 Plus Ventilator
should be observed to verify normal operation. If abnormal performance is observed, additional measures may be necessary, such as re-
orienting or relocating the V60/V60 Plus Ventilator.
d. Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m.
e. According to IEC 60601-1-2: 2014
D-4
Regulatory compliance
Rated maximum 150 kHz to 80 MHz 150 kHz to 80 MHz 80 MHz to 800 MHz 800 MHz to 2.7 GHz
output power of outside ISM bands in ISM bands
transmitter
(W) 3.5 12 12 23
d = ------- P d = ------- P d = ------- P d = ------- P
V1 V2 E1 E2
For transmitters rated at a maximum output power not listed above, the recommended separation distance d in me-
ters (m) can be determined using the equation applicable to the frequency of the transmitter, where P is the maxi-
mum output power rating of the transmitter in watts (W) according to the transmitter manufacturer.
NOTE 1: At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
NOTE 2: The ISM (industrial, scientific and medical) bands between 150 kHz and 80 MHz are 6.765 MHz to 6.795
MHz;13.553 MHz to 13.567 MHz; 26.957 MHz to 27.283 MHz; and 40.66 MHz to 40.70 MHz.
NOTE 3: An additional factor of 10/3 has been incorporated into the formulae used in calculating the recommended
separation distance for transmitters in the ISM frequency bands between 150 kHz and 80 MHz and in the frequency
range 80 MHz to 2.7 GHz to decrease the likelihood that mobile/portable communications equipment could cause
interference if it is inadvertently brought into patient areas.
NOTE 4: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and
reflection from structures, objects and people.
NOTE 5: The minimum separation distance for RF communication equipment operating within the following fre-
quency bands is 0.3 m:
• 380 –390 MHz (TETRA 400)
• 430 – 470 MHz (GMRS 460, FRS 460)
• 704 – 787 MHz (LTE Band 13, 17)
• 800 – 960 MHz (GSM 800/900, TETRA 800, iDEN 820, CDMA 850, LTE Band 5)
• 1 700 –1 990 MHz (GSM 1800; CDMA 1900; GSM 1900; DECT; LTE Band 1, 3, 4, 25; UMTS)
• 2 400 – 2 570 MHz (Bluetooth, WLAN, 802.11 b/g/n, RFID 2450, LTE Band 7)
• 5 100 – 5 800 MHz (WLAN 802.11 a/n)
D-5
Regulatory compliance
RF immunity
The frequencies specified are not yet part of formal regulatory standard IEC 60601-1-2
4.0ED. They are based on 1) a working draft of IEC60601-1-2 4.1ED:2018 Table 11
Medical electrical equipment – Part 1-2: General requirements for basic safety and essen-
tial performance – Collateral Standard: Electromagnetic disturbances – Requirements and
tests, and 2) AIM Standard 7351731 2.00ED:2016.
D-6
Regulatory compliance
For medical electrical equipment and systems that meet this standard, the
minimum necessary separation distances are shown in Annex J of the AIMS
standard 7351731, as well as the guidance required by standards such as IEC
60601-1-2.
For medical electrical equipment and systems that do not meet this standard,
the minimum necessary separation distances can be determined using the
guidance required by standards such as IEC 60601-1-2.
k
d = --- P
E
Cables That May Cables, such as remote alarm cables, longer than 3.05-m may affect the
compliance of the ventilator system with the emissions and immunity
Affect IEC 60601-1-2 requirements of IEC 60601-1-2.
Compliance
WEEE recycling Waste electrical and electronic equipment (WEEE) recycling directive.
directive Waste electrical and electronic equipment must not be disposed of as unsorted
municipal waste at the end of its expected service life. It must be collected
separately and must be disposed of per local regulations. Contact your Philips
authorized representative for information concerning the decommissioning of
your equipment.
This device contains a lithium ion battery that cannot be recycled. Please
contact customer service for safe disposal instructions of this part.
D-7
Regulatory compliance
Classification
Protection Against Electric Class I
Shock
Safety
IEC 60601-1; Medical electrical equipment – Part 1: General requirements for
2012, Ed. 3.1 basic safety and essential performance
IEC 60601-1-6; Medical electrical equipment – Part 1-6: General requirements for
2013, Ed. 3.1 basic safety and essential performance; collateral standard: usabil-
ity
IEC 60601-1-8; Medical electrical equipment – Part 1-8: General requirements for
2012, Ed. 2.1 basic safety and essential requirements; collateral standard - alarm
systems
ISO 14971; 2007 Medical devices – Application of risk management to medical de-
vices
IEC 62304; 2015, Medical device software - Software life cycle processes
Ed. 1.1
D-8
Regulatory compliance
Applied parts The V60/V60 Plus Ventilator system includes these applied parts:
• Patient interfaces
• Tracheal and endotracheal tubes
• High flow therapy nasal cannula and interface
• Nebulizer T-adapter
• Ventilator breathing system - Type B (inspiratory or expiratory pathways
through which gas flows at respiratory pressures and bounded by the
ports through which gas enters and the patient-connection port),
which can also include the following:
- Humidifier chamber
- Patient circuits
Accessible parts The V60/V60 Plus Ventilator system includes these accessible parts:
• Filters
• Roll stand
• Humidifier
• O2 monitor/analyzer
• Nebulizer controller
Detachable The V60/V60 Plus Ventilator system includes these detachable components
(see Figure 3-4 and Figure 3-5):
components
• Left side panel
• Right side panel
• Air inlet filter (under side panel)
Essential Per ISO/EN 80601-2-12: 2011, Medical electrical equipment Part 2-12:
Particular requirements for basic safety and essential performance of critical
performance
care ventilators, the ventilator’s essential performance requirements are given
in “Control settings” on page 11-1, “Alarms and other messages” on page 9-
7, and “Table of monitored parameters” on page 8-2. Alarms, including O2
supply failure alarms and gas failure alarms, are identified in “Alarms and
other messages” on page 9-7. AC mains power information is given in
“Connecting to AC power” on page 5-2. Battery backup information is given in
“About the backup battery” on page 3-10. Gas connection information is given
in “Connecting oxygen” on page 5-1 and “Installing oxygen inlet connector
and AC power cord” on page A-7.
D-9
Regulatory compliance
D-10
Appendix E. Diagnostic mode
In the diagnostic mode you select the language of software display, set the
date and time, select pressure units, enable software options, and calibrate the
touchscreen.
Entering the WARNING: To prevent possible patient injury, do not enter the diagnostic mode while
a patient is connected to the ventilator. Verify that the patient is
diagnostic mode disconnected before proceeding.
2. Press and hold the Accept button on the top-right front of the
ventilator and turn on the ventilator by pressing the ON/Shutdown key.
E-1
Diagnostic mode
3. Within less than 5 seconds, release and press the Accept button
again. The Diagnostics Menu (Figure E-1) is displayed.
E-2
Diagnostic mode
System settings From the System Settings screen (Figure E-2) you can perform the functions
below.
E-3
Diagnostic mode
Language
The Language function lets you set the language of software display.
1. From the System Settings screen, select Language to display the Set
Language screen (Figure E-3).
E-4
Diagnostic mode
2. The active language is shown in white type. Select the new language.
E-5
Diagnostic mode
Date/Time
The Date/Time function lets you verify date and time settings.
1. From the System Settings screen, select Date/Time to display the Set
Date and Time screen (Figure E-5).
2. Adjust the date and time with the + and - buttons; then Apply.
E-6
Diagnostic mode
Pressure Units
The Pressure Units function lets you select the unit of measure for pressure
display.
1. From the System Settings screen, select Pressure Units to display the
Set Pressure Units screen (Figure E-6).
2. The active pressure unit is shown in white type. Select the desired
pressure unit. The change is effective after you restart the ventilator.
E-7
Diagnostic mode
E-8
Diagnostic mode
Software Options
With the Software Options function, you enable a software option using a
unique code specific to the option and the ventilator serial number. Options
can also be enabled through the Respi-Link remote service program.
NOTE: Before installing an option, verify that the ventilator serial number
matches the serial number shown in the Vent Info window (“Vent Info
(ventilator information)” on page 6-18. If the serial numbers do not
match, contact Philips.
2. Use the onscreen keypad to enter the code; then select Enter. The
screen displays Enabled: followed by the name of the software option.
E-9
Diagnostic mode
Baud Rate
The Baud Rate function lets you set the baud rate for serial communications.
1. From the System Settings screen, select Baud Rate to display the Set
Baud Rate for Serial Communications screen (Figure E-9).
2. The active baud rate is shown in white type. Select the desired baud
rate.
E-10
Diagnostic mode
2. The current setting is shown in the Information box at the top of the
screen. If Alarm Volume Escalation is currently Disabled, you will see
a selectable Enable button. If Alarm Volume Escalation is currently
Enabled, you will see a selectable Disable button. Press the button to
change the setting.
3. The new setting is applied after the V60/V60 Plus Ventilator is shut
down and powered on again.
E-11
Diagnostic mode
Service NOTE: All ventilator mode and alarm settings, alarm messages and
significant events are automatically logged and retained, even when
power is lost.
The Service screen lets you view the event log. Other service functions are for
use by authorized service personnel.
E-12
Diagnostic mode
3. The Significant Event Log opens (Figure E-12). Use the buttons on
right side to navigate through the log.
E-13
Diagnostic mode
NOTE: If the Touch Screen Calibration button does not respond, press the
Accept button on the top-right front of the ventilator to begin.
2. Follow the steps shown. Press on the middle of each target with a
blunt, narrow object.
E-14
Diagnostic mode
Exiting the diagnostic Exit the diagnostic mode by turning off ventilator power with the ON/Shutdown
key.
mode
E-15
Diagnostic mode
E-16
Glossary
AC Alternating current.
Alarm Volume escalation When enabled, this function becomes active if there is
no response to a high priority alarm within 40 seconds. Ventilator alarm
volume then increases to its maximum over a 20-second period.
BTPS Body temperature (98 °F, ambient pressure), 100% saturated (with water
vapor).
Glossary-1
Glossary
DISS Diameter index safety standard, a standard for high-pressure gas inlet
fittings.
EPAP Expiratory positive airway pressure. A control setting. The application and
maintenance of pressure above atmospheric at the airway throughout the
exhalation phase of positive-pressure mechanical ventilation.
ET Endotracheal.
Exhalation Port test Performed to assess the leak flow rate through the
exhalation port.
HFT High flow therapy, a feature that provides a constant flow of mixed air and
oxygen.
Glossary-2
Glossary
ID Inner diameter.
Inop Inoperative.
L Liter.
Mandatory breath A breath for which either the timing or volume is controlled
by the ventilator. That is, the machine triggers and/or cycles the breath.
Glossary-3
Glossary
mL Milliliter.
mm Millimeter.
OD Outer diameter.
PIP Peak inspiratory pressure. The peak pressure for the previous inspiration.
Glossary-4
Glossary
Pt. Leak The leak resulting from leaks around the mask or from unintentional
leaks in the circuit. A monitored parameter shown when the intentional leak is
known.
Resistance The pressure drop across a pneumatic device (i.e., bacteria filter,
patient circuit tubing) for a unit of flow when the volume of the device remains
constant, i.e., cmH2O/mL/sec.
SIS Sleeve Indexed System (Australia). A connector for high-pressure gas inlet
fittings.
Spontaneous breath A breath for which both the timing and volume are
controlled by the patient. That is, the patient both triggers and cycles the
breath.
Standby Suspends ventilation and retains current settings when the clinician
wants to temporarily disconnect the patient from the ventilator.
Glossary-5
Glossary
TI/TTOT Inspiratory duty cycle. Inspiratory time divided by total cycle time,
averaged over 8 breaths, a monitored parameter.
Glossary-6
Index
A message 9-7
AC power Average volume-assured pressure support mode. See AVAPS
how to connect to 5-2 mode
specifications 11-8
AC power cord, how to install A-7–A-8 B
Accessories, part numbers C-1–C-4 Backup alarm 3-10
Air inlet filter. See Filter, air inlet Backup battery. See Battery, backup
Alarm LED Bacteria filter must be installed onto gas outlet message 9-7
description 3-7 Baseline pressure, description 4-2
state during alarm conditions 9-3 Batch settings, how to make 6-3, 6-19
Alarm Reset button, function 9-5 Battery, backup
Alarm Silence button, function 9-5 description 3-10–3-11
Alarm tests 5-9–5-10 how to install A-4–A-6
Alarm Volume Escalation location 3-9
definition E-11 operation time 3-10
how to enable or disable E-11 part number C-4
status display 6-17 specifications 11-8
Alarms Baud rate
adjustable, specifications 11-4 for ventilator used with Philips monitor and VueLink
Check Vent (high-priority), description 9-3 Open Interface B-2
Check Vent, troubleshooting table 9-12–9-16 how to change E-10
high-priority, description 9-3 Breath frequency. See Rate
how to clear autoreset alarms from the Alarms list 9-5 Breath phase/trigger indicator, definition 8-2
how to hide/display messages 9-6 Breathing circuit. See Patient circuit
how to manually reset 9-5 Brightness, display, how to set 6-17
how to respond to 9-1 Buzzer, backup 3-10
how to set 6-12
how to silence 9-5
loudness, how to adjust 6-17
C
Calibration, touchscreen E-14
low-priority, description 9-3 Cannot Reach Target Flow alarm 7-7, 9-7
messages, list 9-7–9-17 Care and maintenance 10-1–10-9
See also name of specific alarm C-Flex setting, definition 6-23
settings Check Vent alarm, description 9-3
how to change 6-12 Check Vent: 1.8 V Supply Failed alarm 9-12
list of descriptions and ranges 6-26–6-27 Check Vent: 12 V Supply Failed alarm 9-12
troubleshooting table 9-7–9-17 Check Vent: 24 V Supply Failed alarm 9-12
Vent Inoperative (high-priority), description 9-3 Check Vent: 3.3 V Supply Failed alarm 9-12
Vent Inoperative, troubleshooting table 9-16–9-17 Check Vent: 35 V Supply Failed alarm 9-13
visual alarm indications 9-2 Check Vent: 5 V Supply Failed alarm 9-12
Alarms and messages 9-1–9-17 Check Vent: Air Flow Sensor Calibration Data Error alarm 9-
Assembly, ventilator A-2–A-8 13
Auto-Trak sensitivity Check Vent: Alarm LED Failed alarm 9-13
description 3-3 Check Vent: Auxiliary Alarm Supply Failed alarm 9-13
principles of operation 4-3–4-6 Check Vent: Backup Alarm Failed alarm 9-13
Auto-Trak+ option Check Vent: Barometer Calibration Data Error alarm 9-13
description 4-6 Check Vent: Barometer Sensor Range Error alarm 9-13
how to change settings 6-18–6-19 Check Vent: Battery Failed alarm 9-13
settings and ranges 11-4 Check Vent: Battery Temperature High alarm 9-13
AVAPS (average volume-assured pressure support) mode Check Vent: Blower Stalled 9-14
precautions 1-1, 1-2 Check Vent: Blower Temperature High alarm 9-14
principles of operation 4-11–4-12 Check Vent: Cooling Fan Speed Error alarm 9-14
AVAPS Maximum IPAP Pressure setting. See Max P Check Vent: CPU PCBA ADC Failed alarm 9-14
AVAPS Minimum IPAP Pressure setting. See Min P Check Vent: Data Acquisition PCBA ADC Failed alarm 9-14
AVAPS: Target VT Exceeded. Min Pressure Too High mes- Check Vent: Flash File System Error alarm 9-14
sage 9-7 Check Vent: Internal Temperature High CPU alarm 9-14
AVAPS: Target VT Not Achieved. Insufficient Max Pressure Check Vent: Internal Temperature High Daq alarm 9-14
Index-1
Index
Check Vent: Internal Temperature High Mtr alarm 9-14 how to change language E-4–E-5
Check Vent: Machine Pressure Sensor Auto-Zero Failed how to change pressure unit E-7
alarm 9-14 how to enable or disable Alarm Volume Escalation E-11
Check Vent: Machine Pressure Sensor Calibration Data Error how to enable software options E-9
alarm 9-15 how to enter E-1
Check Vent: Machine Pressure Sensor Range Error alarm 9- how to exit E-15
15 how to restore default factory settings E-8
Check Vent: Motor Control PCBA ADC Failed alarm 9-15 how to view event log E-12–E-13
Check Vent: O2 Flow Sensor Calibration Data Error alarm 9- Dimensions, ventilator 11-6
15 Disinfecting
Check Vent: O2 Pressure Sensor Calibration Data Error alarm ventilator exterior 10-3
9-15 Display, brightness, how to set 6-17
Check Vent: O2 Supply Pressure Sensor Range Error alarm Disposal 10-8
9-15
Check Vent: OVP Circuit Failed alarm 9-15 E
Check Vent: Oxygen Device Failed alarm 9-15 E-cycle (expiratory cycle Sensitivity) setting, definition 6-23
Check Vent: Primary Alarm Failed alarm 9-15 Elastance, definition 4-13
Check Vent: Program CRC Test Failed alarm 9-15 Electrical specifications 11-7, 11-8
Check Vent: Proximal Pressure Sensor Auto-Zero Failed Electromagnetic compatibility (EMC), compliance with stan-
alarm 9-15 dards D-1
Check Vent: Proximal Pressure Sensor Calibration Data Error Environmental specifications 11-6
alarm 9-15 EPAP (expiratory positive airway pressure) setting, definition
Check Vent: Proximal Pressure Sensor Range Error alarm 7- 6-23
7, 9-16 Estimated exhaled tidal volume. See VT
Circuit, patient. See Patient circuit Estimated minute ventilation. See VE
Cleaning Estimated total leak. See Tot.Leak
ventilator exterior 10-2 Event log, how to view E-12–E-13
CO2 rebreathing precautions 1-2, 1-4, 1-7, 1-8, 3-2 Exhalation port
Communications interface B-1–B-6 how to select 6-12–6-15
using the ventilator with Philips monitors and VueLink part numbers C-2
Open Interface B-3–B-5 Exhalation port test, how to run 6-16–6-17
Connector Exhale breath phase indicator, definition 8-2
oxygen inlet Expiratory positive airway pressure. See EPAP
how to install A-7
location 3-9
remote alarm/nurse call, location 3-9
F
Fan filter. See Filter, cooling fan
RS-232 serial and analog I/O, location 3-9
Filter
Continuous positive airway pressure. See CPAP
air inlet
Continuous-tone alarm 3-10
how to install 10-6
Contraindications 3-2
maintenance schedule 10-5
Control settings
cooling fan
how to change 6-3, 6-4, 6-19
how to clean or replace 10-7
how to make batch setting changes 6-19
list of descriptions and ranges 6-23–6-26 location 3-9
ranges, resolutions, and accuracies 11-1–11-2 maintenance schedule 10-5
See also name of specific setting part number C-4
Cooling fan filter. See Filter, cooling fan main flow (inspiratory) bacteria, part numbers C-4
CPAP (continuous positive airway pressure) mode 4-8 First-time installation A-1–A-9
CPAP (continuous positive airway pressure) setting, defini- Fitting. See Connector
tion 6-23 Flow assist/maximum resistance setting. See Max R
Frequency, breath. See Rate
D
Date and time, how to change E-6 G
Default factory settings, how to restore E-8 General information 3-1–3-12
Definitions F-1–F-6 Glossary F-1–F-6
Delivered pressure specifications 11-10 Graphical user interface
Diagnostic mode E-1–E-15 how to calibrate E-14
how to calibrate touchscreen E-14–E-15 how to use 3-13
how to change baud rate E-10 illustration 3-12
how to change date and time E-6 GUI. See Graphical user interface
Index-2
Index
Index-3
Index
Oxygen Not Available alarm 9-10 preparing for ventilation 1-4–1-7
preventive maintenance 10-4
P remote alarm B-5
Parts and accessories C-1–C-4 Preparing for ventilation 5-1–5-13
Patient alarms are disabled during HFT message 7-7, 9-10 Pressure Regulation High alarm 9-11
Patient circuit Pressure unit, how to change E-7
how to install 5-3–5-7 Pressure, baseline, description 4-2
part numbers C-3 Pressure-controlled ventilation mode. See PCV
specifications 11-8 Preventive maintenance 10-4–10-8
Patient Circuit Occluded alarm 7-7, 9-10 schedule 10-5
Patient data Principles of operation 4-1–4-15
ranges, resolutions, and accuracies 11-3 Proportional pressure ventilation mode. See PPV mode
See also Monitored parameters Proximal Pressure Line Disconnect alarm 9-12
symbols for invalid or out of range data 8-1 Pt. Leak (patient leak) monitored parameter 8-2
Patient Disconnect alarm 9-10 Pt. Trig (patient-triggered breaths) monitored parameter 8-2
Patient interface
how to select for leak adjustment purposes 6-12–6-15 R
See Masks Ramp Time setting, definition 6-25
Patient leak. See Pt. Leak 8-2 Rate (Respiratory Rate) setting, definition 6-25
Patient monitoring 8-1–8-3 Rate monitored parameter, definition 8-2
Patient-triggered breaths. See Pt. Trig Regulatory compliance D-1–D-9
PCV (pressure-controlled ventilation) mode, principles of op- Remote alarm cable kits B-6
eration 4-9 Remote alarm port B-5–B-6
Peak inspiratory pressure. See PIP Remote alarm/nurse call connector, location 3-9
PIP (peak inspiratory pressure) monitored parameter, defini- Repacking and shipping 10-9
tion 8-2 Resistance, definition 4-13
PM. See Preventive maintenance Respi-Link
Port, exhalation description 3-4
how to select 6-12–6-15 location of Ethernet connector 3-9
how to test 6-16–6-17 Respiratory rate. See Rate
part numbers C-2 Respironics V60 Ventilator
Power cord front view 3-7
how to install A-8 physical description 3-4–3-9
location 3-9 potential side effects 3-2
Power cord retainer, location 3-9 rear view 3-9
Power has been restored message 9-11 side view 3-8
Power indicators, illustration 3-11 system overview 3-3–3-4
PPV (proportional pressure ventilation) mode Rise (Rise Time) setting, definition 6-25
adjusting settings 6-7 RS-232 serial port B-2
principles of operation 4-13–4-14 location B-1
setup 6-7–6-11 Running on Internal Battery alarm 9-12
PPV % setting, definition 6-25
PPV gain setting. See PPV % setting S
PPV Max P alarm 9-11 S/T (spontaneous/timed) mode, principles of operation 4-10
PPV Max V alarm 9-11 Safety, compliance with standards D-8
PPV Maximum Pressure Limit setting. See Max PPV Scalars. See Waveforms
PPV Maximum Volume Limit setting. See Max V Screen lock 6-18
Precautions Settings
alarms and messages 1-8 default factory, how to restore E-8
AVAPS 1-1 See also Control settings, Alarm settings, or name of spe-
backup battery 5-8 cific setting
care and maintenance 1-8–1-9 Shutdown, ventilator 3-15
cleaning, disinfecting, and sterilizing 10-2, 10-3 Software options, how to enable E-9
CO2 rebreathing 1-2, 1-4, 1-7, 1-8, 3-2 Specifications. See Technical specifications
communications interface 1-9–1-10 Spont (spontaneous) breath type indicator, definition 8-2
Diagnostic mode 1-10 Spontaneous/timed mode. See S/T mode
first-time installation 1-9 Stand, ventilator
general 1-1–1-4 mounting the ventilator to A-2–A-3
high flow therapy (HFT) 1-7, 7-1 Standby 6-20–6-21
operation 1-7 Startup
packing and shipping 10-9 time specifications 11-10
Index-4
Index
ventilator startup 3-15 sors Failed alarm 9-17
Symbols 2-1–2-9 Vent Inoperative 1008 Machine and Proximal Pressure Sen-
System Settings functions, in diagnostic mode E-3 sors Failed alarm 9-17
Vent Inoperative 1009 Pressure Regulation High alarm 9-17
T Vent Inoperative 100A Data Acquisition PCBA ADC Refer-
Technical specifications 11-1–11-9 ence Failed alarm 9-17
alarm settings 11-4 Vent Inoperative 100B Watchdog Test Failed alarm 9-17
control setting ranges, resolutions, and accuracies 11-1– Vent Inoperative alarm, description 9-3
11-2 Ventilation modes
delivered pressure 11-10 how to change 6-2
dimensions 11-6 principles of operation 4-7–4-14
electrical 11-7, 11-8 Ventilator breathing circuit. See Patient circuit
environmental 11-6 Ventilator settings. See Control settings or Alarm settings
high flow therapy (HFT) 11-1, 11-10 Verifying ventilator operation 5-8
monitored parameter ranges, resolutions, and accuracies Volume
11-3 AVAPS Target Tidal Volume. See VT
patient circuit 11-8 estimated exhaled tidal. See VT
patient data ranges, resolutions, and accuracies 11-3 waveform. See Waveforms
ventilator startup time 11-10 Volume assist/maximum elastance setting. See Max E
weight 11-6 VT (AVAPS Target Tidal Volume) setting, definition 6-26
Tests VT (estimated exhaled tidal volume) monitored parameter,
alarm tests 5-9–5-10 definition 8-2
exhalation port 6-16–6-17 VueLink Open Interface, using with the ventilator and Philips
TI/TTOT (duty cycle) monitored parameter, definition 8-2, B- monitors B-3–B-5
3
Tidal volume, estimated exhaled. See VT W
Time and date, how to change E-6 Warnings, cautions, and notes 1-1–1-10
Timed breath type indicator, definition 8-2 Waveforms
Tot.Leak (estimated total leak) monitored parameter, defini- description 8-2
tion 8-2 how to freeze and unfreeze 8-3
Total leak. See Tot.Leak how to scale axes 8-2
Touchscreen WEEE recycling directive, compliance statement D-7
how to calibrate E-14 Weight, ventilator 11-6
Training information 3-15
Trigger (trigger sensitivity) setting, definition 6-26
Trigger +x, E-Cycle +x message 9-12
Triggering
principles of operation 4-3
volume method 4-3
Troubleshooting alarms 9-7–9-17
U
Unpacking and inspection A-1
Using Default Settings message 9-12
V
Vent Info (Ventilator Information) window, description 6-18
Vent Inoperative 1000 3.3 V Supply Failed alarm 9-16
Vent Inoperative 1001 12 V Supply Failed alarm 9-16
Vent Inoperative 1002 Blower Temperature Too High alarm
9-16
Vent Inoperative 1003 Internal Temperature High alarm 9-
16
Vent Inoperative 1004 Internal Temperature High alarm 9-
16
Vent Inoperative 1005 Internal Temperature High alarm 9-
17
Vent Inoperative 1006 Data Acquisition PCBA ADC Failed
alarm 9-17
Vent Inoperative 1007 Machine and Proximal Pressure Sen-
Index-5
Index
Index-6
www.philips.com/healthcare
[email protected]
Australian sponsor
Philips Electronics Australia Ltd
65 Epping Road
North Ryde, NSW Australia 2113
You can find the most current electronic copy of this user manual at:
www.philips.com/IFU
Printed in USA
1047358 Rev AA * 3 2021 989805612141