WITH DUAL (FRONT AND REAR) USB

AND SD MEMORY CARD PORT

AND SIDE PANEL AUX INPUT

PWR

WITH DUAL (FRONT AND REAR)USB AND SD

MEMORY CARD PORT AND SIDE PANEL AUX INPUT

07-2012
INSTRUCTIONS INSTRUCTIONS

CONTENTS ACCESSORY
Panel Introduction 02
Basic Functions 03
Remote Control Function 05
Turn the Unit On/Off 07
Enter into the Main Interface 07
Play SD card/USB memory device 07
Radio Function Operation 08
Disc Function Operation 09
Play/Eject Disc 09
DVD/VCD Disc Playback 09
CD Disc Playback 09
MP3/WMA Format Disc Playback 09
Touch Menu Function 09
Access setup interface 11
General setting 11
Time setting 11
Language Setup 11 DVD Parental control function
Video Setup 11
Audio setting 12 DVD Parental control function
Steering Wheel Setup 12
Touch calibration 12
Bluetooth Function Operation DVD Parental control function：The default set
14 for DVD is #8 adult, which means all grades of
iPod function operation 15 DVD can be read without entering password.To
External input operation 15 change the default grade,you need to follow the
below procedure: Press SETUP button on the
Other Function Operations 15 remote, display will show the system set up menu
Rear view function 15 and the submenu,select password and enter
0000, you will be able to choose the DVD
Wiring Diagram 16 grade as default.
Trouble shooting 16
Specifications 17
Accessory 18
DVD Parental control function 18

Warning: To ensure safety while driving and to comply with laws, drivers should not
watch video or operate the video device while driving.

01 18
INSTRUCTIONS INSTRUCTIONS

SPECITICATIONS Panel Introduction

Power supply DC 12V
Power range 10.8-16.0V DC
Max operate current 15A
Ground system Negative ground
Amp Rating 85 WattsX4 Channels
FM tuner
European frequency range 87.5-108MHz
USA frequency range 87.5-107.9MHz
Signal / Noise ratio 55dB
Stereo separation 30dB
Search station volt 20-30dBuv
Distortion rate 1.5%
AM tuner
European frequency range 522-1620KHz
11 12
USA frequency range 530-1710KHz 9

Limit noise sensitivity 32dB

1. / PWR Button
DVD player
2. DBAS Button
Signal / Noise ratio 70dB
3. DN Button
Frequency response 20Hz-20KHz
4. VOL- Button
5. MUTE Button
This unit is with switchable frequency.
You can switch from USA frequency to Europe frequency by following the 6. VOL+ Button
below steps:
Step1. In main menu, press setup icon to enter the setup interface. 7. UP Button
8. Eject Button
Step2. Press the Radio icon,and insert password 123456, then press “OK”,
the menu from which you can select the radio frequency will show. 9. USB Slot
10. RESET Button
Step3. Press “Radio region” and select the desired frequency by pressing the "up"
and "down" arrow, then press it and setting is finished. 11. AUX External Input
12. Remote Control Receiver

17 02
INSTRUCTIONS INSTRUCTIONS

BASIC FUNCTION WIRING DIAGRAM

This player is equipped with ISO standard connector, please follow below instruction:
1. / PWR Button ● Red - ACC ON (+12V) ● Grey/Grey black - Right front speaker (+/-)
Short press this button to power on, long press this button to power off. ● Yellow – 12 V Constant ● White/White black - Left front speaker (+/-)
In normal situation, press PWR button can return to the main menu. ● Black – Ground wire ● Purple/Purple black - Right rear speaker (+/-)
● Blue - Power Antenna / Remote Amp Turn On ● Green/Green black - Left rear speaker (+/-)
2. DBAS Button ● Orange – Back-Up Camera Trigger (+) ● Pink – Parking Brake (-)
Press this button to bass on/off.

Front right speaker

Rear right speaker
Rear USB/SWC
Bluetooth MIC
IPOD

Video output 2
+ Green Purple +
Rear Rear

Video input
Green/black Purple/black

AUX input
- -
3. DN Button +
Left track speaker
White
Right track speaker
Grey +
Front White/black Grey/black Front
Press this button to make the LCD monitor down. - -

4. VOL- Button
Press this button to reduce the volume.

Wire plug
5. MUTE Button
Press this button to shut off the sound output, re-press this button can resume the
sound output, long press this button can turn off the TFT LCD display.

Radio antenna

Rear left speaker

Front left speaker

Subwoofer output

CCD

Wire socket

Video output 1
6. VOL+ Button
Press this button to increase the volume.

7. UP Button TROUBLE SHOOTING

Press this button to make the LCD monitor UP.
PROBLEM CAUSE SOLUTION
8. Eject Button
Press this button can eject the disc. Check fuse Change fuse same as the old one
Cannot power on Some factors cause MPU Press RES button on the panel by
9. Dual (front and rear) USB wrong operation penpoint, then, power on
Warning: You can only use either front or rear USB at a time. Never connect both After ignition switch
front and rear USB at the same time! This could cause malfunctions. off ,setting Change battery or fuse Reset information and save
information all lose
10. RESET Button
Poor performance Weak signal Move the car to another place, then research
Press this button and this unit will be restored to the initial state.
of radio station
11. Dual (front and rear) AUX Connot load disk There is a disk inside Remove disc before inserting another one
Warning: You can only use either front or rear AUX at a time. Never connect both Disc is scratched Change new disc
front and rear AUX at the same time! Put wrong side of disc into
Cannot play disc Insert in the disk with sign side up
the unit
12. Remote control receiver
It is able of receiving infrared signals launched by the remote control matching the unit. Lens is dirty Clean lens by lens clean disc
Cannot switch There is only one language/ If disc is not with multi-language/subtitle,
language/subtitle subtitle in disc it cannot switch language/subtitle

No image Other factors cause MPU Press [RES] button on the panel by
wrong operation penpoint, then, power on

Cannot watch It’s not allowed to watch image Park the car in a safe place, put the car stall
image during during driving in “ P ” postion, pull up the hand brake,
driving parking brake wire must be grounded

03 16
INSTRUCTIONS INSTRUCTIONS

iPod function operation

Connect to iPod first, touch [iPod] icon on main interface to access iPod interface, as 14 15 13
shown in below diagram.

Play / Pause Fast forward play / Fast backward play Volume adjustment knob

Previous Song / next Song

Stop
Back to the main interface

External input operation

Connect the video input plug with external video input jack, and connect the audio input
plug with external audio input jack.
Touch [Input] icon on main interface to access external input interface.
Audio You can adjust thevolume, bass, pitch for input audio.
You can adjust the speaker volume by adjusting the front and back,left and right column.
Video You can adjust the brightness, contrast, saturation and hue for input video.
You can also choose the video standard mode. 13. SD Slot

14. Disc Slot

15. Slot indicator light

Warning: In AUX mode, you can adjust the angle of screen by press region 1 & region 2.
Press Region 1 to slide up, press Region 2 to slide down.

Other functions
Rear view function
In any running state, the video signal can switch to reverse video state when reversing the
car, and the system shall return to its initial running state after reversing the car.
Warning
Do not rely on CCD system completely, please make sure you use direct eyesight while
driving.Back rearview system only assists in driving. As the distance range of rearview
system is limited, completely relying on the rearview system during driving may cause
accidents.

Reverse field simulation Rearview backup image

15 04
INSTRUCTIONS INSTRUCTIONS

REMOTE CONTROL FUNCTION Bluetooth Function Operation

28
3. SOURCE Button Enter/exit
Press this button to change mode. Touch [ Bluetooth ] icon in the main interface to enter the bluetooth interface.
Touch icon to exit bluetooth interface.
4. EQ Button
Press this button to choose POP、ROCK、 Pair/link
CLASSIC、EQ off. To use Bluetooth hand-free function, make connection first, i.e. match the host with the
Bluetooth mobile phone.
5. SEEK+ ( )/ SEEK-( ) Button Operation methods:
In normal playback MP3、USB、SD songs,
Set the host to be matching state, and open the Bluetooth of your mobile phone and use
Press this button to previous song or next
the mobile phone to search device, the mobile phone shall prompt to match password with
song.
the Bluetooth when it has searched the Bluetooth device.
Input Bluetooth password (0000) to the mobile phone and confirm. The mobile phone
6. VOL+ ( ) / VOL- ( )
shall prompt whether authorize to this device,please select [Yes]. Phone and Bluetooth
Press this button to increase or decrease
shall automatically connect within 20 seconds. Under any working mode, the host shall
volume level.
convert to Bluetooth state if there is an incoming call. And the host shall restore to current
mode after hanging up.
7. SEL Button
Press this button to choose sound feature. When the Bluetooth device matches with this device, the connection status shall display
“ LINK OK ”, otherwise, it shall display “ NO LINK ”.
8. LOUD Button Dialing
Press this button to startup LOUD function. You can dial on mobile phone directly or input phone number through the number buttons
on the screen, click to delete if there is input error.
POWER ON/OFF AMS / RPT 9. BAND-P/N Button After input the phone number, click to make a call, and click to hang up the phone.
MUTE TITLE In radio mode, press this button to choose Click during a call so as to switch the voice between car speaker and mobile phone.
SOURCE AUDIO band.
EQ SET PLAYING TIME In VCD、DVD mode, press this button to Call records
SEEK+ / SEEK- SUBTITLE choose AUTO、PAL or NTSC system. Click to access call records interface as below PIC 2:
VOL+ / VOL- PBC / MENU Received calls: Touch this button to check all the phone numbers of received calls.
SEL UP / DOWN / L / R ENTER 10. LOC/RDM Button Dialed numbers: Touch this button to check all the dialed phone numbers.
LOUD SLOW In radio mode, press this button to switch Missed calls: Touch this button to check all the phone numbers of missed calls.
BAND / P / N ANGLE between local and direction. Bluetooth volume
LOC / RDM SETUP In VCD、CD mode,press this key to randomly Click to access Bluetooth volume interface as below PIC 3:
STOP OSD play.
PLAY / PAUSE ZOOM
ST / PROG MENU 11. STOP Button
O-10+ DSP Press this button to stop playing.

12. PLAY/PAUSE Button

Press this button to switch between play and
1.POWER pause.
Press once to switch on, press again to In stop mode, press this button to play. PIC 1 PIC 2
PLAY / PAUSE

switch off. previous song

13. ST/PROG Button
next song
2. MUTE Button In radio mode, press this button to choose
Press once to turn off audio output, stereo or mono station. PIC 3

press again to resume volume level. In audio mode, it can help STOP button to
programmed play.

05 14
INSTRUCTIONS INSTRUCTIONS
14. 0-10+ Button 22. SLOW Button
Press this button to choose desired song、 In audio mode, press this button to slow
section、preset stations. backward and slow forward.
Decimal numbers, for example the 19th
song, press 1.9 button; 23. ANGLE Button
Centesimal numbers, for example, the In DVD mode, press this button to change
120th song, press 1.2.0 button. play angle.

15. AMS / RPT Button 24. SETUP Button

In radio mode, press this button to browse In audio mode, press this button to choose
stored stations. different set items.
In audio mode, press this button to play
repeatedly. 25. OSD Display
Press this button to display the title chapter
16. TITLE Button and the left time.
In DVD mode, press this button to play
back to the top menu of disc. 26. ZOOM Button
In DVD/VCD mode, press this button to
17. AUDIO Button ZOOM in.
In DVD mode, press this button to switch
language of dialogue. 27. MENU Button
In VCD mode, press this button to choose Press button to back to the main menu.
left track、right track and stereo.
28. DSP
18. SET playing time Press this button to show the time.
In DVD mode, press this button, you can
define playing time. BATTERY CHANGE
When control distance of remote control
19. SUBTITLE Button becomes shorter or no function, please
picture (6). In DVD mode, press this button to switch change battery. Please confirm polarity
picture (5)
language of subtitle. before change.
One hand press stopper, then pull out battery.
20. PBC Button
In VCD mode, press this button to display
all song menus, work with number button
to choose songs.

21. UP、DOWN、LEFT、 RIGHT、ENTER Put battery into controller.

Button
When playing MP3、USB、SD returns to
song menu, up、down selections can be
up / " " button or down / " " key to
select up and down, select and press " "
key to confirm. Insert battery holder into controller.
The selected tracks can be played. Press
the left or right arrow keys to " " or " "
key, can be on the next page function
operation.

13 06
INSTRUCTIONS INSTRUCTIONS

Turn on/off Host Audio setting

When the ignition switch is put in ACC or ON position,Press[ ] button on the front panel Click icon on setup interface to access audio setting interface, as shown in
to turn on the unit.After the host starts, hold [ ]button for 3 seconds , the host will turn off. right(PIC 1) diagram:
You can turn on or turn off the existing functions on audio setting interface.

Access main interface

In the other mode, click on the interface to return the icon will switch to the main interface.

Touch the function icons so as to access the

corresponding function operations.
USB/SD Card function operation
When there is a USB device/SD card connected, PIC 1
the unit can conduct the playback of audio/video/ Steering wheel setting
image files in the USB device/SD card.
I. Click icon on setup interface so as to access steering wheel setting interface.
Insert/eject USB storage device II.Connect anode and cathode of direction control wire of the car with anode and cathode
1. Connect a USB recorded with media information to the unit by a USB connecting cable. of direction control wire of this device, and press the buttons on steering wheel one by
one and record the corresponding sequence and functions, then click [Allocation].
2. When there is a need to eject the USB device, exit the USB device playback screen
first, and then take out the device. III. Click the button of steering wheel needs to be allotted so as to select the
corresponding setting function, such as volume +.
Insert/eject SD card
IIII. Buttons on steering wheel shall display the corresponding functions, such as volume + .
1. Insert a SD card recorded with media information into the SD card slot in the unit
To modify function settings, repeat procedures 3~4. Click [Enter] to save the settings.
correctly until it is locked.
2. When pulling out the SD card, exit SD card playing state first, then press the SD card To reset functions, click [Reset] icon, all the settings set before shall be cleared, repeat
and it shall pop up after unlocking. procedures 3~4 for resetting.

Enter/exit
Insert a USB storage device or SD card to automatically play data contained in it. If the Touch calibration
unit has connected with a USB device or SD card, touch[ USB ]icon in the main interface If touch calibration error occurs, you can adjust the touch coordinate by “Touch calibration”.
to enter into the external storage playback interface; Touch[ SD ]icon to enter into the SD Click icon on setup interface, input password [888888] to confirm to access touch
card playback interface. During playback, touch the top center area of the screen to pop calibration interface, as shown in below diagram:
up the touch menu, operate touch menu to perform various playback controls.
Touching methods
Play Use touch pen to click the center of “+” icon, and move along with center of “+” icon so
After SD card/USB removable device being read out, the operation methods are similar as to calibrate the screen. It shall automatically save data and exit after screen calibration.
to disk operation methods. Please accurately click all positions on screen, or the accuracy of touch calibration shall
be affected.

07 12
INSTRUCTIONS INSTRUCTIONS

Access setup interface Radio Function Operation

Click [Setting] icon on main interface to access setup interface.
Enter/exit
Touch [ RADIO ] icon in the main interface to enter into the radio interface.
General setting Touch icon to return to main interface, and then touch other function icons so as to exit
Click icon on setup interface to access general setting interface, as shown in below radio mode.
PIC 1 diagram: Band selection
In general setting interface, you can select to turn on or turn off the existing functions. Click [BND] icon so as to switch among FM1,FM2, FM3,AM1, AM2, bands.
You can set wallpaper and opening picture you like and check version number of DV/DC,
click icon to browse up/down. Search/Save radio stations
Short press [Scan] icon to browse the stored radio stations.
Wallpaper selection FM band can save 18 radio stations (Six stations for FM1/FM2/FM3), AM band can save
Click icon on wallpaper bar
other1 other1 , direction icon shall pop up, click it to 12 radio stations (Six stations for AM1/AM2).
select wallpaper. Scan radio
Short press icon to manually fine-tune radio stations upward/downward.
Time setting Long press icon to automatically search and save radio stations.
Click icon on setup interface to access time setting interface, as shown in below Sound setting
PIC 2diagram:
Click [EQ] icon can switch to different sound mode.
Click icon on time bar time setting interface shall display, as shown in
below PIC 3 diagram: Mute on/off
Click icon beside hour and minute to separately set hour and minute. Click [Mute] icon to turn on/off mute function
TFT on/off
Click icon to turn off TFT, and then click the screen area so as to turn on TFT.
other1 Click icon so as to slide screen angle.
BOSS

RDS Function
RDS function provides series information (such as traffice information, name of station),
PIC 1 PIC 2 PIC 3 and can automatically switch to the station with stronger signal and carries the same
program.
Language Setup AF: Touch the button to turn on/off AF mode
During use, you can select your familiar language to display menu by language setup.
TA: Touch the button to turn on/off TA mode
Click icon on setup interface to access language setting interface, as shown in right
(PIC 4) diagram: PTY: Touch the button the screen displays program types, users can
Click the corresponding icon on the language bar desired to be set so as to switch search station according to program type
the language type, when there are more than 3 languages, direction icon shall pop up,
If the unit does not have RDS function, it has no AF/TA/PTY function. The
click it to select your familiar language.
corresponding icon appears grey.
Video setting
Click icon on setup interface to access video setting interface, as shown in right
(PIC 5) diagram:
At video setting interface, you can adjust brightness, contrast, saturation and hue of the video.

PIC 4 PIC 5
11 08
INSTRUCTIONS INSTRUCTIONS

Disc Function Operation Access next menu

Touch it to access the next menu interface.
Play/eject disc Time setting
Play disc Touch this button to access time setting interface.
Insert the disc into the disc slot with the printing surface up, system will detect the disc
and automatically take it in to read and play. Stereo on/off
Touch it so as to turn on/off stereo.
Eject disc
(1) Click button on the panel to eject the disc. Return to root menu
(2) If a disc has not been took away 15 seconds after it is ejected, system will Touch this icon, it shall return to root menu of disk in DVD state and access PBC
automatically take in the disc but not play. menu playing in VCD state. All chapters in the disk shall be displayed on the interface,
Do not insert two discs or more. touch the chapter icon directly for playing.
DVD/VCD disc playback Access title menu
Press this button to return to title menu of the disk. Directly click menu bar at title
During playback of disc, touch the middle lower area of the screen to pop up the touch
menu interface for playing.
menu, operate the touch menu to perform various playback controls.(PIC 1)
Repeat play
CD Disc Playback
In playing state, touch this button to start repeat play function: Chapter repeat
After a CD is inserted, system shall access disc reading state immediately. Title repeat repeat all Off.
When there is a disc in the device, click [Disc] at the main interface so as to access disc
reading state. During VCD playing, this function only works when PBC is off.
After the disc being read out, system shall automatically play in sequence. Language selection
MP3/JPEG/MPEG4 disk playing Touch this button to select language.
When the disc contains readable files, such as MP3/JPEG/MPEG4 files, it shall be Digit keyboard
automatically read out and played after slipping into DVD player. Touch this button and digit keyboard shall appear, click number buttons directly to
During playing, touch the screen area and the touch menu shall pop up. Operate the select tracks for playing.
touch menu for various playing.
Randomly play
Touch Menu Function Description Touch this button to instantly play each song. Press again to back to the normal play.
Play/pause Zoom in/Zoom out image
Touch the button to pause, retouch it to continue to play. Touch this button to zoom in /zoom out the image.
Stop
Touch the button to enter into prestop status.
Fast forward/backward
Consecutively touch this button to select the speed of fast-forward/fast-backward.
The previous/next song
Touch the button to select the previous/next song.
Volume adjustment button
Touch this button and volume adjustment modulation shall pop up, touch button to
adjust the volume.
TT 1/5 CH 1/1 x TT 1/5 CH 1/1 x

00 00

VOL VOL

00:01:44 00:09:43 00:01:44 00:09:43

PIC 1

09 10