B.

Program studi Teknik Elektronika

1 Basic PLC Trainer LGLS XGT0901 16 Digital input & 16 digital output 8 Unit #REF! #REF!
Desain kompak, cerdas dan tangguh
Kemudahan bagi pengguna pemula
Dapat melakukan eksperimen sendiri
Dapat mengembangkan aplikasi otomatisasi industri

Memungkinkan untuk menggunakan piranti input/output eksternal

Dapat digunakan untuk komunikasi antar PLC atau PC
2 Automtic Control Trainer Electron - 2 system model builders to simulate system transfer function 1 Unit #REF! #REF!
- 2 multi-input adder/summing nodes
- Reference generator and function generator

- a. Linear non Linear Process - Electron - 2 system model builders to simulate system transfer function
Controller - 2 multi-input adder/summing nodes
- Reference generator and function generator

- b. Process Controlller Electron The controller is configurable for P, PI, PID operation , with time
constant selectable in range of several decades.

- c. Oven Temperatur Controller Electron - Equipped with four different types of commonly used temperatur
sensors (J-TC, NTC,PTC, Bi-metalic swtch)

- d. DC Motor Speed Control Electron - The module has two small DC motors ganged together. One is
used as the drive mototr and the other as a tachometric feedback
generator.A slot type optical feedback sensor is also mechanically
ganged to a DC motor

- e. Servo Potensiometer System ELECTRON - This module includes a geared DC motor.which operates a screw-
driven mechanism, ganged to the slide of a linear potentionmeter.A
second linear potentiometer allows the setting the refence position.

- f. Light Control Module Electron - It includes a light source (incandescent lamp) and three different
types of sensor (photo-resistance, photodiode, photo-transistor).
Each one is equipped with its oqn interface circuit, to experiment
open and closed loop system in automatic control setup.

- g. Flow Control Module Electron - This module includes one of most commonly used flow sensors,
the rotary vane type flow meter.
 h.A/D and D/A board for PC Based Control Electron - The trainer is used in conjunction with a PC, and creates an
intelligent interface to the experiment modules, for the purpose
data, pre-setting analog and digital output and sampling input
terminal. It can also be used as a general-purpose microcomputer
system to experiment software developed for automated
system.The microcomputer unit is based around a CMOS
microprocessor of the Z80 family.

3 Tank Level Control Electron - The unit consists of a tank with a LED bar indication of the 1 Unit #REF!
liquid level. Inlet and outlets ducts with are conneted to the tank
and have simulated electrovalves, represented by LED lamps.The
flow rate can be manually by means of simulated taps
(potensiometer). An on-board intergrator and A/D coverter
reproduces the resulting tank level.The resulting output signals are
available as PLC input.
#REF!
4 Reactor Vessel Control Electron 1 Unit #REF!
- The loading position is capable of dispensing metal washers into
the belt. An unloading position is provided with a proximity
sensor, which is used to identify the presence of the washer in the
unloadning area. The washer can be unloaded or not as
programmed.Two collecting bins are supplied, one at the output of
the unloader and another at the end of the conveyor belt. #REF!

5 Connection Simulation Panel for - Electron - 16 toggle switches for PLC input simulation 1 Unit #REF! #REF!
PLC Machine - 16 LED indicator for PLC output monitoring
- 16 2mm jacks tied to PLC inputs
- 16 2mm jacks tied to PLC output
- 40 pole flat cable connector to interface the simulator madules
- Auxiliary 24 V power jacks

6 Silo System Electron The simulator includes a loading coveyor belt, a silo and an 1 Unit #REF! #REF!
unloading coveyor belt. The system can work under manual control
as well as under PLC control.The internal circuits of the board
visual effects of the movement of packs in this simulator.

7 Conveyor Belt System Electron - The loading position is capable of dispensing metal washer into 1 Unit #REF!
the belt.An unloading position is provided with a proximity sensor,
which is used to identify the presence of the washer in the
unloading area.Two collecting bins are supplied, one at the output
of unloader and another at the end of the conveyor belt.
#REF!

8 Washing Machine System Electron - The module follows the design philosophy of the other modules, 1 Unit #REF! #REF!
and consists in the simulation of water supply and drainage,
temperature control, motor speed control and sequential cycling
according to different operation programs.
 PID/Fuzzy Logic Control Electron - Universal input for thermocouples, RTD's mA Volt (pre-wired for
Volt)
9 - PID / FuzzyLogic Controller Electron - 3 Logic inputs 1 Unit #REF! #REF!
10 - Flame Control System Simulator Electron - Relay ,SSR drive, analog mA or V valve control main output
(pre-wired for Volt) 1 Unit #REF! #REF!
11 - Oven Control System Simulator Electron - PID or PID + Fuzzy (XF) algorithm 1 Unit #REF! #REF!
12 - Pressure Control System Simulator Electron - Auto-tune and Expert-tune 1 Unit #REF! #REF!
- Auto/Man
- Auxiliary relay outputs
- 2 memorized setpoints
- Capability of serial communications with Modbus/Jbus protocol

- Switching power supply 100…240 Vac with low voltage 24 V

output for simulator board

13 Paket Trainer Robot Super Lengkap e-Technology Body robor beroda,sensor api,4 sensor jarak,materi 1 Unit #REF!
praktikum,software,roda dan motor,kit mikrokontroller BS2p ,drive
motor DC,servo motor,sesor kompas, mototr stepper,TPA81,sensor
sungut line follwer #REF!
- Smart Motor Controller Atmel at892051 - Berbasis SPC006 smart controller AT892051 2 Unit #REF! #REF!
- memiliki interfac I2C dan 4 jalur paralel
- Tiap modul bisa digunakan untuk mengendalikan hingga 2 motor
DC
- Gearbox Tamiya Mobil Tamiya 4 Unit #REF! #REF!

- DT-AVR low Cost Micro - Atmel atmege8535 - 8 kbyte flash memory,512 byte SRAM dan 512 byte EEPROM 5 Unit #REF! #REF!
( Programmer Mikrokontroler) - Osilator 4 MHz

- Rangkaian reset, tombol manual reset dan brown out detector

14 Buckling Arm Robot Crrus Crawler - Arm Robot 5 DOF Crust Crawer 1 Unit #REF! #REF!
15 Sensor and Intelligent LN ·     1 x Inductive sensor 1 Unit #REF! #REF!
·     1 x Capacitive sensor
·     2 x Optical sensors
·     1 x Reflector
·     1 x Sensor testing device for binary sensors
·     1 x 3-component workpiece
·     1 x Universal sensor holder to accommodate cylindrical
sensors M4 - M18
·     1 x Profile bracket
·     1 x Workpiece carrier
·     4 x M12 plugs (connector accessories)
·     1 x Connection adapter for M12 plug-in connectors
·     1 x Set of fasteners
·     1 x Set of Allen keys
·     1 x Storage case
16 Solder Uap (blower) Hakko PR801 - Power :100 V - 310 W, 110V - 360 W, 120V-430W, 220C-570W, 2 Unit #REF! #REF!
230V-630W, 240V - 680W
- Capacity 5 to 20 L/min (max)
 - Hot Air temperatur : 100 to 500ºC/200 to 930ºF(Nozzle A1130
used)
- Jig Saw 550 Watt Krisbow Voltage 220Volt/50 Hz 2 Unit #REF! #REF!
No load speed 500 - 3000 r/min
Cutting depth Wood 65 mm, Steel 5 mm
17 Eprom Eraser Leap Eprom eraser - Capacity 64pcs 24 pin x0.6" 4 Unit #REF! #REF!
- U-v tube GL-10.1pc
- Wavelength 2537ºA
- U-V Intensity 5000 Wcm
- Tube Life 4000 hours
-Erasure Timer pre settable up 60 minutes
-Input Power 115/220/240 V /50 Hz
18 Universal Programmer Hilo -Device Support Pin Count:from 8 pins up to over 300 pins 4 Unit #REF! #REF!
- Device Contact: Default- DIP48 textool
- Max Sockets in parallel : 8 sockets on optional gang
programming module
- Control : 16 bits hight-speed controller with big sized FPGA &
CPLD
- Interface Port : 1x USB port.
- Data transfer Rate :USB 1.1 : 12 Mb/s, USB 2.0 : 480 Mb/s
- Max sites in parallel :up to 8 via tiered star USB
- Power :100-240 V/ 50W,Frequency 50-60 Hz
19 X-Y recorder (Plotter) Yokogawa - Input, type plug-in module(each unit has a built-in A/D converter) 1 Unit #REF! #REF!
- number of slots : 8 8 (up to 16 channels)

- Logic inputs : 16 (bbitsx2)

- Max record length Standard : 2.5 MW/CH,50 MW total
/M1 : 10 MW/CH,250 MW total
/M2 : 25 MW/CH,500 MW total
/M3 : 50 MW/CH,500 MW total
- Time axis accuracy :± 0.005%
- Time axis setting range : 500ns-30 sec/div,1 min-30 min/div, 1-
-h12h/div, 1 day-3days/div(up
Acquisition modes : Normal 30 days) Avetrangin, box
, envelope,
averange
- Rate supply voltage : 100 to 120 VAC/200 t0 240 VAC
- Frequency : 50/60 Hz
- Power comsumption : 200 VA-Max
- Withstand voltage : 1500 VAC for one minute across power
supply and ground
- Insulation resistance : 10 MΩ or one greater at 500 VDC across
power supply and ground.
20 Power Elektronic Trainer K&H Kl 500 - UJT Experiments 1 Unit #REF! #REF!
- PUT Experiments
- PUT & SCR Experiments
- SCS Experiments
- UJT & PUT trigger SCR Experiments
- SCR Control DC Motor & DIAC, TRIAC Characteristic
Experiments
 Automatic Control
- Temperature Lamp
Ratio & & Couple
Photo TRIAC & Control
TouchSpeed Experiments
Control
Experiments
- Over/Under Voltage Breaker & Flasher Control Experiments
- TRIAC Liquid Level & IC Timer Switch Experiments
- Digital Signal Driver & Zero Voltage Swicth Experiments
- Zero Voltage Swicth Experiments
- SCR Converter Experiments
- SCR Rectifier Experiments
- JFET/MOSFET speed Control Experiment
- IGBT Characteristic & IGBT speed Control Experiments
21 Function Generator GwInstek Gfg8219a - Frequency Range 0.3 Hz-3 MHz 10 Unit #REF! #REF!
- Amplitude > 10 Vpp (into 50 Ω load)
- Impedance 50Ω±10%
- Attenuator -20dB±1dBx2
- DC Offeset ,-5V - >5V (into 50W load)
- Duty Control 80%:20%:80% to 1 MHz Continue variable
- Display 6 digit LED display
Sine Wave
Distortion ≤ 1 %, 0,3 Hz - 200 kHz
Flatness < 0.3 dB, 0.3 Hz - 300 kHz
< 0.5 dB, 300.Hz - 3 MHz
Triangle Wave
Linier : ≥ 98 %, 0.3 Hz - 100 kHz
≥ 95 %, 100.kHz - 3MHz
Square Wave
Symmetry : ± 2%, 0.3 Kz - 100 kHz
Rise or Fall Time ≤ 100nS a maximum output (ino 50Ω load)
CMOS Output
Level : 4Vpp±1Vpp-14.5Vpp±0.5Vpp adjustable
Rise or Fall Time ≤ 120nS
TTL Output
Level : ≥3Vpp
Fan Out : 20 TTL load
Rise or Fall Time ≤ 25nS
VCF
Input Voltage : 0V-10V ±1V (100:1)
Input Inpedance : 10kΩ±10%
GCV
Output Voltage : to set the voltage between 0V - 2 V as per -
different frequency.
Sweep Operation
Sweep/Manual : Switch selector
Sweep/Rate : 100:1 ratio max and adjustable
Sweep/Time : 0.5 sec- 30 sec adjustable
Sweep/Mode : Lin/Log switch selector
Amplitude Modulation
Depth : 0 - 100%
 MOD Frequency : 400 Hz (INT) DC - 1 MHz (EXT)
Carrier BW : 100 Hz - 3 MHz (-3dB)
EXT Sensitivity : ≤ 10 Vpp for 100% modulation
Frequency Modulation
Deviation : 0 - ± 5%
MOD Frequency : 400 Hz (INT) DC - 20kHz (EXT)
EXT Sensitivity : ≤ 10 Vpp for 10% modulation
Frequency Counter
INT /EXT : Switch selector
Range : 0.3 HZ - 2MHz (5Hz - 150MHz EXT)
Accuracy : Time base accuracy ± 1 count
Time base : ±20ppm (23°C±5°C) after 30 minute warm up

Resolution : The maximum resolution is 100 nHz for 1Hz and 1Hz-
for 100 MHZ
Input Inpedance : 1 MW// 150pF
Sensivity : < 35mVrms (5Hz - 100MHz)
< 45mVrms (100MHz - 150MHz)
Power Source :
AC115V/230V±15%, 50/60Hz
Accessories
Insruction manual x 1, Power cord x 1 GTL-101 x 2
Dimension : & Weight
251(W) x 91(H) x 291(D)mm, approx 2,2 kg

- Power Supply GwInsek gps3303 - Output mode : Voltage 0-30 V (CH1,CH2),5V Fixed (CH3) 5 Unit #REF! #REF!
Current 0-3A (CH1,CH2),3A Max (CH3)
- AC 100 V/120V/220V(±10%)230V(+10%-6%) 50/60 Hz
Constant Voltage Operation (CH1,CH2)
Line Regulation :≤ 0.01% + 3mV
Load Regulaion :≤ 0.01% + 3mV (rating current ≤3A)
≤ 0.02% + 5mV (rating current >3A)
Ripple & Noise : ≤ 1mVrmsm 5Hz - 1MHz
Recovery Time : ≤ 100 µS (50% Load change , Minimum load
0.5A)
Constant Current Operation (CH1,CH2)
Line Regulation :≤ 0.2% + 3mA
Load Regulaion :≤ 0.2% + 3mA
Ripple & Noise : ≤ 3mArms
Tracking Operation (CH1,CH2)
Tracking Error : ≤ 0.5% + 10mV of the CH1
Series Regulation : ≤ 300mV
Load Regulaion :≤ 0.01% + 3mV
Ripple & Noise : ≤ 2mArms, 5 Hz - 1MHz
5 V FIX Output (CH3) Load regulation ≤ 15mV
Current Output 3A
Meter
Digital : 3 digits 0.5" LED display
 Out On Accuracy : ± (0.5% rgd + 2 digits)
Out Off Accuracy : ± (0.5% rgd + 8 digits)
Insulation
Chassis and terminal ≥ DC 500V / 20MΩ
Chassis and AC Cord ≥ DC 500V / 30MΩ
Accessories

Test lead GTL-104 x 2,GL-105 x 1 : European test lead GTL-203 x

1, GTL-204 x 2
Dimension & Weight : 255(W)x145(H)x265(D):Approx 6.3kg

22 Everprecision PCB Prototyping Everprecision - Resolution : 0.005 mm 1 Unit #REF! #REF!

- Control Axis : X,Y,Z
- Control motor : X,Y,Z / stepper motor
- Max.Travel Speed : 50mm/sec.
- Max.Working Speed : 20 mm/sec
- Min. Trace Width : 4mil
- Drilling : 0.3 -∞mm
- Drilling Performance : 90 Stroke/min
- Tool Change : manual
- Tool Holder : 1/8" Socket
- Tool Length Detec : Auto Tool Length Detect
- Surface Detect : Auto Surface Detect
- Spindle Speed : 35.000 rpm (max)
- Power Comsumption : AC 110/220 V, 200 Watt