Professional Documents
Culture Documents
UHF Digital/Analog Mobile Transceiver Service Manual: Vertex Standard LMR, Inc
UHF Digital/Analog Mobile Transceiver Service Manual: Vertex Standard LMR, Inc
Mobile Transceiver
©2014 Vertex Standard LMR, Inc.
EVX-5300/-5400
EC114U90E
Service Manual
EVX-5300 EVX-5400
Introduction
This manual provides technical information necessary for servicing the EVX-5300/-5400 UHF Digital/Analog Mobile Trans-
ceiver.
Servicing this equipment requires expertise in handling surface-mount chip components. Attempts by non-qualiied persons to
service this equipment may result in permanent damage not covered by the warranty, and may be illegal in some countries.
Two PCB layout diagrams are provided for each double-sided circuit board in the transceiver. Each side of is referred to by the
type of the majority of components installed on that side (“leaded” or “chip-only”). In most cases one side has only chip com-
ponents, and the other has either a mixture of both chip and leaded components (trimmers, coils, electrolytic capacitors, ICs,
etc.), or leaded components only.
As described in the pages to follow, the advanced microprocessor design of the EVX-5300/-5400 allows a complete alignment
of this transceiver to be performed without opening the case of the radio; all adjustments can be performed from the personal
computer, using with the Vertex Standard FIF-12 USB Programming Interface and CE142 Software.
While we believe the technical information in this manual to be correct, Vertex Standard assumes no liability for damage that
may occur as a result of typographical or other errors that may be present. Your cooperation in pointing out any inconsistencies
in the technical information would be appreciated.
Important Note
This transceiver is assembled using Pb (lead) free solder, based on the RoHS speciication.
Only lead-free solder (Alloy Composition: Sn-3.0Ag-0.5Cu) should be used for repairs performed on this apparatus.
The solder stated above utilizes the alloy composition required for compliance with the lead-free speciication, and any
solder with the above alloy composition may be used.
Contents
Speciications Alignment..................................................... 12
USA/EXP Models ...................................... 2 Circuit Diagram
EU Model ................................................... 3 MAIN Unit (FR026490A: TYPE “G6”) ...... 23
DSUB 15-pin Accessory Connector ............. 4 MAIN Unit (FR024860B: TYPE “G7”) ...... 25
Exploded View & Miscellaneous Parts ....... 5 MAIN-2 Unit (FR026490A: TYPE “G7”) ... 27
Parts List ........................................................ 6 FRONT-A Unit (FR024850C: EVX-5300) .. 29
Block Diagram............................................... 8 FRONT-B Unit (FR025010C: EVX-5400) .. 30
Circuit Description..................................... 10
RA1252400
SPECIAL NUT (M9)
RA1261500
SP HOLDER
M4090203
SPEAKER
RA1234300
RA1486200 PACKING PAD (COVER)
RA1245900 RUBBER KNOB
VOLUME KNOB
CB6649000 RA123460A
EVX-5300 FRONT PANEL ASSY TYPE “G6”, 25W: G1095437 (RA30H3847M1A) SHIELD CASE COVER (TOP)
TYPE “G7”, 25W: G1095438 (RA30H4452M1A)
EVX-5300 FRONT PANEL ASSY (Component) TYPE “G6”, 45W: G1095428 (RA60H3847M1A)
FRONT PANEL ASSY (8ch) TYPE “G7”, 45W: G1095429 (RA60H4452M1A)
NAME PLATE (EVX-5300) IC (Power Module)
RA127870A
FRONT-A Unit (Component) SHIELD CASE COVER (JACK)
Printed Circuit Board with Components
CONNECTOR CB6656000 (EVX-5300, TYPE “G6”, 45W)
LED CB6657000 (EVX-5300, TYPE “G6”, 25W) RA0790300
HOLDER (LED) CB6658000 (EVX-5400, TYPE “G6”, 45W) SHIELD CASE (POWER)
LIGHT GUIDE (LED) (3 pcs) CB6659000 (EVX-5400, TYPE “G6”, 25W)
SHEET (LED)
MAIN Unit (FR026490A w/DC Power Cord) DSUB CONNECTOR
CB6645000 (EVX-5300, TYPE “G7”, 45W)
LED FILTER (8CH) CB6646000 (EVX-5300, TYPE “G7”, 25W) ACCESSORY
BLIND SHEET (L10) CB6647000 (EVX-5400, TYPE “G7”, 45W)
CB6648000 (EVX-5400, TYPE “G7”, 25W)
MAIN Unit (FR024860B w/DC Power Cord)
CB6728000 (EVX-5300, TYPE “G7”, 45W)
CB6729000 (EVX-5300, TYPE “G7”, 25W)
CB6730000 (EVX-5400, TYPE “G7”, 45W)
CB6731000 (EVX-5400, TYPE “G7”, 25W) Q9000375
MAIN Unit (FR026490A w/DC Power Cord) SURGE ABSORBER
RA1264700
EXT CAP
RA127990A T9207533
INSULATOR (10X5) WIRE ASSY
RA123740A
T92075281 PAD (20X20X4)
WIRE ASSY RA079080A
PAD (DIODE)
RA125440A
PAD (10X17)
SUPPLIED ACCESSORIES RA129240A
SPONGE RUBBER (FW)
DESCRIPTION VXSTD P/N QTY.
DC CABLE
EVX-5400 FRONT PANEL ASSY (Component) EVX-5400 FRONT PANEL CB6652000
FRONT PANEL ASSY (512ch) P1091362 (BNC)
45 W Mode: 02P 15A UL 2.8M T9026415 1 FRONT-B Unit P1091412A (mini-UHF)
NAME PLATE (EVX-5400)
25 W Mode: 02P 10A UL 2.8M T9026510 1 CONNECTOR
RA1486200
BLADE FUSE FRONT-B Unit (Component) RUBBER KNOB
50 W Mode: ATY-N15 Q0000175 1 Printed Circuit Board with Components RA123450B
25 W Mode: ATY-N10 Q0000177 1 CONNECTOR CHASSIS
LCD
BRACKET RA1234700 1
LIGHT GUIDE (LCD)
KNOB SCREW RA079060A 2 LCD HOLDER
HEX HEAD BOLT (HSM5X12B) U9900209 2 INTER CONNECTOR RA1252400
SPECIAL NUT (M9) RA1234400
DOUBLE FACE R7069960 1 REFLECTOR SHEET (093) PACKING PAD (PANEL)
BRACKET MOUNTING SCREWS REFLECTOR SHEET (SUB)
SPONGE RUBBER (LCD) RA1261500
PAN HEAD SCREW (M5X20) U00520001 4 SP HOLDER
BLIND SHEET (L10)
PAN HEAD TAPPING (5X20 #1) U40520101 4
M4090203
HEX NUT (N5) U60500301 4 MAIN Unit / MAIN-2 Unit (Component) SPEAKER
RA1245900
SPRING LOCK WASHER (SW5B) U71005007 2 Printed Circuit Board with Components VOLUME KNOB
PLAIN WASHER (FW5) U70005001 8 WIRE ASSY (DC Power Cord)
TOOTHED LOCK WASHER (OW5) U72005007 4
CHASSIS ASSY (Component) CB6651000
No. VXSTD P/N DESCRIPTION QTY. CHASSIS EVX-5400 FRONT PANEL ASSY
SPONGE RUBBER (FW)
U03308002 SEMS SCREW ASM3X8NI 2 PAD (10X17)
Q0000175 BIND HEAD TAPTITE-B M3X8 12 PAD (20X20X4)
U72005007 SPRING LOCK WASHER SW2.6 2 PAD (DIODE)
Non-designated parts are available only as parts of a designated assembly.
Electrical Parts
SPEAKER 20-ohm 5015134H02 M4090203
CONNECTOR ANT (mini-UHF) P1091412A
CONNECTOR ANT (BNC) P1091362
SURGE ABSORBER DSP201M-S00B Q9000375
WIRE ASSY T92075281
WIRE ASSY DC Power Cord T9207533
1-2. First mixer The processed speech signal from the custom IC Q1001
The RF signal is mixed with the 1st local signal between (OMAP) is supplied to the modulator section of the custom
352.15 and 419.15 MHz (Type “G6”) or 399.15 and 469.15 IC Q1070 (RFIC), which modulates the speech signal into the
MHz (Type “G7”) in the 1st mixer Q1053 (AK1220), to pro- FM or digital signal.
duce 50.85 MHz 1st IF signal.
2-2. drive & Final ampliFier stages
The 1st local signal is generated by the VCO, which consists The modulated signal from the custom IC Q1070 (RFIC)
of Q1055 (2SK508), varactor diodes D1029 (1SV279), D1032 is buffered by Q1061 (2SK3077) and amplified by Q1052
(Type “G6”: 1SV279, Type “G7”: 1SV280), D1036 (1SV279), (RD01MUS1), and then is applied to the Power Module
and D1037 (Type “G6”: 1SV279, Type “G7”: 1SV280). The Q1046 (RA60H3847M1A: Type “G6”, RA60H4452M1A:
1st local signal is supplied to the 1st mixer Q1053 (AK1220) Type “G7”), which is ampliied up to 45 watts output power.
through the buffer amplifier Q1064 (2SC5006) and Q1066
The transmit signal then passes through the antenna switch
(2SC5226).
D1018 and D1019 (both MA4P959) and is low pass iltered
1-3. iF ampliFier & demodulator to suppress away harmonic spurious radiation before delivery
The 1st IF signal is applied to the monolithic crystal filter to the antenna.
XF1001 to strip away all but the desired signal, and then sup-
2-3. automatiC transmit power Control
plied to the custom IC Q1070 (RFIC) through the IF ampliier
The forward power of the Power Module Q1046
Q1068 (2SC5226). The custom IC Q1070 (RFIC) converts
(RA60H3847M1A: Type “G6”, RA60H4452M1A: Type
the 1st IF signal into the Base Band signal.
“G7”) is detected by D1020 (HSM88AS), and then applied to
The Base Band signal from the custom IC Q1070 (RFIC) is the comparator Q1074 (ADM8566ARM).
applied to another custom IC Q1001 (OMAP), which is de-
The comparator Q1074 (ADM8566ARM) compares detected
modulated by the Digital Signal Processor.
voltage of forward power and power control voltage from
1-4. audio ampliFier custom IC Q1070 (RFIC), makes output power stable by con-
The demodulated signal from the custom IC Q1001 (OMAP) trolling the bias voltage RF ampliier Q1052 (RD01MUS1).
is applied to another custom IC Q1044 (PMAIC), which Additionally, output voltage of operational amp Q1043 (AD-
convert to analog signal. The output signal from the custom M8566ARM) is supplied to Power Module. The output level
IC Q1044 (PMAIC) is applied to the AF amplifier Q1015 is controlled by Q1070 (RFIC) to three level (45 watt model)
(NJM12902) and Q1027 (TDA1519CTH). The output signal or two level (25 watt model).
from Q1027 (TDA1519CTH) is applied to the front panel
audio speaker or external speaker which is connected to the The Relection power from the antenna is detected by D1021
EXT SP jack (J1004). (HSM88AS), Automatic transmission power control circuit
protect equipment. For example, when the antenna is not con-
nected.
Frequency
Counter
msK deviation
This parameter is to align “MSK Deviation” which use for the ANI operation of the MDC1200 System.
1. Press the “MSK” button to open the “MSK Deviation Align-
ment” window.
2. Click the “PTT” button or press the “SPACE” bar of the com-
puter’s keyboard to transmit the radio.
3. Set the value to get desired deviation (Nominal: 3.0 kHz) on
the deviation meter according to the following ways:
l Dragging the slide bar
l Clicking the arrow buttons
l Pressing the left/right arrow key of the computer’s keyboard
l Entering the value (“–20.00” - “20.00”) in the “Currend
Data” box from the computer’s keyboard
ê
4. After getting the desired deviation, click the “PTT” button or
press the “SPACE” bar to stop transmitting.
5. Click the “OK” button to inish the MSK Deviation alignment
and save the data.