Professional Documents
Culture Documents
BS 5163-2-2004
BS 5163-2-2004
SUPPLIED BY BSB UNDER LICENCE FROM BSI FOR VA TECH WABAG LIMITED - CHENNAI ON 31/07/2014
valves and associated water control
apparatus — Specification
ICS 23.060.30
12&23<,1*:,7+287%6,3(50,66,21(;&(37$63(50,77('%<&23<5,*+7/$:
BS 5163-2:2004
SUPPLIED BY BSB UNDER LICENCE FROM BSI FOR VA TECH WABAG LIMITED - CHENNAI ON 31/07/2014
Pipeline Industries Guild
Society of British Water Industries
Water UK
Contents
Page
Committees responsible Inside front cover
Foreword ii
1 Scope 1
2 Normative references 1
3 Terms and definitions 1
4 Design requirements 3
5 Preparing for storage and transport 4
Annex A (normative) Test method for the resistance of stem caps to
operating loads 5
SUPPLIED BY BSB UNDER LICENCE FROM BSI FOR VA TECH WABAG LIMITED - CHENNAI ON 31/07/2014
Bibliography 7
Figure 1 — Ring key and bar 2
Figure 2 — T key 3
Figure 3 — Typical stem cap 4
Table 1 — Dimensions of stem caps 3
Foreword
This part of BS 5163 has been prepared under the direction of Technical
Committee PSE/7 to facilitate the application of BS EN 1074-1:2000,
BS EN 1074-2:2000 and BS EN 1074-6:2004. Along with BS 5163-1:2004,
BS EN 1074-1:2000 and BS EN 1074-2:2000, this standard supersedes
BS 5163:1986, which is withdrawn.
This standard gives details of stem caps not covered in BS EN 1074-1:2000,
BS EN 1074-2:2000 or BS EN 1074-6:2004.
This publication does not purport to include all the necessary provisions of a
contract. Users are responsible for its correct application.
Compliance with a British Standard does not of itself confer immunity
SUPPLIED BY BSB UNDER LICENCE FROM BSI FOR VA TECH WABAG LIMITED - CHENNAI ON 31/07/2014
from legal obligations.
Summary of pages
This document comprises a front cover, an inside front cover, pages i and ii,
pages 1 to 7 and a back cover.
The BSI copyright notice displayed in this document indicates when the
document was last issued.
1 Scope
Isolating valves and hydrants installed in underground pipelines primarily carrying water intended for
human consumption within the United Kingdom are required to be fitted with a stem cap to enable them
to be operated by a ring-key and bar or T-shaped key.
The stem cap is fitted to the top of the valve stem to convert the manufacturer’s stem configuration to mate
with operating keys.
Two sizes of stem cap are specified, covering respectively, valves from DN 50 through DN 300 and DN 350
through DN 600.
SUPPLIED BY BSB UNDER LICENCE FROM BSI FOR VA TECH WABAG LIMITED - CHENNAI ON 31/07/2014
NOTE Stem caps are also commonly used on other waterworks apparatus, e.g. penstocks (specified in BS 7775).
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
BS 6615:1996/ISO 8062:1994, Specification for dimensional tolerances for metal and metal alloy castings.
BS EN 1074-1, Valves for water supply — Fitness for purpose requirements and appropriate verification
tests — Part 1: General requirements.
BS EN 1074-2, Valves for water supply — Fitness for purpose requirements and appropriate verification
tests — Part 2: Isolating valves.
BS EN 1074-6, Valves for water supply — Fitness for purpose requirements and appropriate verification
tests — Part 6: Hydrants.
BS EN 1503-3, Valves — Materials for bodies, bonnets and covers — Part 3: Cast irons specified in
European Standards.
3.2
ring key and bar
operating key with a socket at its lower end, which engages with the stem cap on the valve or hydrant, and
a ring at the upper end to enable a bar to be inserted, which can then be used manually to turn the valve
stem
NOTE A ring key and bar is illustrated in Figure 1.
3.3
T key
operating key similar to a ring key and bar but having a fixed short-length upper bar attached centrally at
right angles to the shaft
NOTE A T key is illustrated in Figure 2.
3.4
mST
minimum strength torque as specified in BS EN 1074-1, BS EN 1074-2 and BS EN 1074-6
SUPPLIED BY BSB UNDER LICENCE FROM BSI FOR VA TECH WABAG LIMITED - CHENNAI ON 31/07/2014
NOTE This sketch is diagrammatic only.
SUPPLIED BY BSB UNDER LICENCE FROM BSI FOR VA TECH WABAG LIMITED - CHENNAI ON 31/07/2014
NOTE This sketch is diagrammatic only.
Figure 2 — T key
4 Design requirements
4.1 Materials
4.1.1 Stem cap materials shall be selected from those listed in BS EN 1503-3.
4.1.2 Cast iron components shall be fully coated to provide protection against corrosion.
4.1.3 Components used to secure stem caps to valve stems shall be resistant to corrosion and ageing by the
selection of materials, or shall be protected by appropriate means.
4.2 Dimensions
4.2.1 Stem caps shall comply with the dimensions given in Table 1 and Figure 3. They shall be securely
attached to the valve stem and be designed in such a manner that they can be removed when required. The
method of attachment to the valve stem shall not interfere with the location of the operating key.
Table 1 — Dimensions of stem caps (see Figure 3)
Nominal size Length of cap square, A Square of cap, B
DN mm mm
50, 65, 80, 100, 125, 150, 200, 250, 300 63 35
350, 400, 450, 500, 600 75 48
Dimensions A and B shall have casting tolerance ISO 8062-CT10 (BS 6615:1996/ISO 8062:1994).
NOTE For sizes above DN 600, if a stem cap is required, dimensions should be agreed between purchaser and manufacturer.
SUPPLIED BY BSB UNDER LICENCE FROM BSI FOR VA TECH WABAG LIMITED - CHENNAI ON 31/07/2014
Key
1 Taper 1 in 20 on each side
A Length of cap square (see Table 1)
B Square of cap (see Table 1)
Figure 3 — Typical stem cap
4.2.2 The design of the lower end internal parts of the stem caps is the responsibility of the valve
manufacturer, who shall ensure they can be secured to their design of stems and removed as required. The
design shown in Figure 3 is typical only.
4.3 Resistance of stem caps to operating loads
Stem caps in their delivery condition shall withstand, without failure, an operating torque of 0.8 times
the mST.
Failure is defined as the inability of the stem cap to resist the load for the duration of the test.
Testing shall be in accordance with Annex A.
Annex A (normative)
Test method for the resistance of stem caps to operating loads
A.1 General
The test shall be performed at ambient temperature with a stem cap in its delivery condition.
A.2 Test procedure
Attach and secure the stem cap on a rigidly mounted spigot having the same form and dimensions as the
mating section of the valve stem. Apply a torque load as specified in 4.3 for a minimum of 15 s.
SUPPLIED BY BSB UNDER LICENCE FROM BSI FOR VA TECH WABAG LIMITED - CHENNAI ON 31/07/2014
NOTE The socket used to apply the load should be dimensionally in accordance with BS 336 up to DN 300.
Bibliography
SUPPLIED BY BSB UNDER LICENCE FROM BSI FOR VA TECH WABAG LIMITED - CHENNAI ON 31/07/2014
Revisions
British Standards are updated by amendment or revision. Users of
British Standards should make sure that they possess the latest amendments or
editions.
It is the constant aim of BSI to improve the quality of our products and services.
We would be grateful if anyone finding an inaccuracy or ambiguity while using
this British Standard would inform the Secretary of the technical committee
responsible, the identity of which can be found on the inside front cover.
SUPPLIED BY BSB UNDER LICENCE FROM BSI FOR VA TECH WABAG LIMITED - CHENNAI ON 31/07/2014
Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.
BSI offers members an individual updating service called PLUS which ensures
that subscribers automatically receive the latest editions of standards.
Buying standards
Orders for all BSI, international and foreign standards publications should be
addressed to Customer Services. Tel: +44 (0)20 8996 9001.
Fax: +44 (0)20 8996 7001. Email: [email protected]. Standards are also
available from the BSI website at http://www.bsi-global.com.
In response to orders for international standards, it is BSI policy to supply the
BSI implementation of those that have been published as British Standards,
unless otherwise requested.
Information on standards
BSI provides a wide range of information on national, European and
international standards through its Library and its Technical Help to Exporters
Service. Various BSI electronic information services are also available which give
details on all its products and services. Contact the Information Centre.
Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: [email protected].
Subscribing members of BSI are kept up to date with standards developments
and receive substantial discounts on the purchase price of standards. For details
of these and other benefits contact Membership Administration.
Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001.
Email: [email protected].
Information regarding online access to British Standards via British Standards
Online can be found at http://www.bsi-global.com/bsonline.
Further information about BSI is available on the BSI website at
http://www.bsi-global.com.
Copyright
Copyright subsists in all BSI publications. BSI also holds the copyright, in the
UK, of the publications of the international standardization bodies. Except as
permitted under the Copyright, Designs and Patents Act 1988 no extract may be
reproduced, stored in a retrieval system or transmitted in any form or by any
means – electronic, photocopying, recording or otherwise – without prior written
permission from BSI.
This does not preclude the free use, in the course of implementing the standard,
of necessary details such as symbols, and size, type or grade designations. If these
details are to be used for any other purpose than implementation then the prior
BSI written permission of BSI must be obtained.
389 Chiswick High Road Details and advice can be obtained from the Copyright & Licensing Manager.
London Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553.
Email: [email protected].
W4 4AL