Professional Documents
Culture Documents
Computer Comm Network
Computer Comm Network
Dispersion
5. The optical fiber consists of two concentric cylinders; the inside solid cylinder is called the
core and the surrounding
Figure 2 (optical fiber with core, cladding and total internally reflected ray)
For propagation of light inside the core there are two possibilities.
1. A light ray is launched in a plane containing the axis of the fiber. We can then see the light
ray after total internal
reflection travels in the same plane i.e., the ray is confined to the plane in which it was
launched and never leave the plane. In this situation the rays will always cross the axis of
the fiber. These are called the Meridional rays. (Fig. 2)
2. The other possibility is that the ray is not launched in a plane containing the axis of the
fiber.
For example if the ray is launched at some angle such that it does not intersect the axis of
the fiber, then after total internal reflection it will go to some other plane. We can see that
in this situation the ray will never intersect the axis of the fiber. The ray essentially will
spiral around the axis of fiber. These rays are called the Skew rays.
So it can be concluded that if the light is to propagate inside an optical fiber it could be
through two types of rays
a) Meridional rays: The rays which always pass through the axis of fiber giving high optical
intensity at the center of the core
of the fiber.
b) Skew Rays : The rays which never intersect the axis of the fiber, giving low optical
intensity at the center and high intensity
Let us consider figure 3. A ray is launched from outside (air) at an angle , from the axis
1.
of the fiber.
The question is, under what conditions the ray is ultimately guided inside the core due to
total internal reflections at the core cladding boundary?
Let the ray makes an angle with the axis of the fiber inside the core, and let the ray
2.
make an angle with core
If < critical angle the ray is refracted in cladding. The ray which goes to cladding is lost
and is not useful for communication. The ray which is confined to the core is useful for
optical communication.
Since
decreases and at some point becomes less than the critical angle. When equals the
critical angle, equals . The maximum launching angle then corresponds to .
4. Let us apply Snell's law at the launching point and at the core-cladding interface for the
maximum launching angle
we then have
(since )
now,
So the sine of the maximum angle at which the ray will be guided inside the fiber is given
by square root of the difference of squares of the refractive indices of the core and
cladding. The quantity is called the NUMERICAL APERTURE of an optical fiber.
The NA is a measure of the power launching efficiently of an optical fiber.
5. Numerical Aperture: This parameter tells us that if we take an optical fiber and put it in
front of an optical source then how
much light is collected by the fiber from the source. Smaller the value of N.A, smaller the
value of (maximum launching angle) and smaller is the power accepted by the fiber. In
other words, if the light is available from various directions from the source, only a portion
of light is accepted by an optical fiber and the remaining part of the light is rejected by it.
If we want good light launching efficiency then should be as large as possible. Since
6.
is related to the
difference of the squares of the refractive indices of the core and the cladding, the
difference of squares of the refractive indices should be as large as possible.
So, for good launching efficiency, should be large compared to . Since the material
for the optical fiber has been chosen as glass, the refractive index of the core is practically
fixed to about 1.5.
The only choice therefore we have is to reduce the refractive index of the cladding for good
launching efficiency. Since (i.e., no cladding) is the minimum possible value, it
suggests that the cladding is an undesirable feature. In the first look it then appears that
the cladding is only for mechanical support.
4. DISPERSION
1. The amount of light accepted by an optical fiber is only one of the parameters in optical
communication. A more
important parameter is the data rate which the fiber can handle since the primary purpose
here is to send information from one point to another.
Figure (4)
2. As we see from the figure 4, all the rays contained within the cone are accepted by
(a) the optical fiber.
Let us take two extreme rays; one at the lowest possible angle (along the axis of the fiber),
and one at the highest
(b) possible angle ( ). Take a length L along the fiber axis traveled by the rays.
(c) Let us now transmit a narrow pulse of light. The light pulse indicates binary information. If
there is a pulse then a bit is
present, otherwise the bit is absent. When the light is switched on, all the rays are switched
on at the same time. The pulse energy is therefore divided between different rays which
travel by different paths inside the fiber.
(d)The pulse along the axis of the optical fiber takes less time to travel the distance L, than
the pulse which travels at the
extreme angle .
The time difference between the axial ray and the extreme ray then is:
where c is velocity of light. Since the core material is glass, , and since , it
can lie between 1 and 1.5.
The ratio then lies between 1 and 1.5 only. The time difference per unit length
therefore is more or less proportional to .
per km ( )
The time difference essentially is the measure of pulse broadening on the optical fiber.
This phenomenon is called DISPERSION of an optical fiber. The dispersion (pulse
broadening) has to be small since the data rate is inversely proportional to the pulse
broadening. For high speed communication (high speed does not refer to the time taken by
data to reach the destination but it refers to the number of bits per sec) the pulse
broadening and hence the dispersion should be minimal.
For low dispersion ( ) should be as small as possible. So for an optical fiber the
(f)
refractive index of core has to
be made as close to the refractive index of cladding as possible.
3. Contradictory Requirement:
(a) For higher launching efficiency (higher NA), should be as large as possible .
(b) For high data rate (bandwidth), should be as small as possible .
Since data transfer rate is rather more important in communication, is made as small
as the fabrication technology permits.
Refractive index of the cladding differs from that of the core by only 0.1 to 1%.
For this fiber the refractive index of the core is constant (see Fig 5). Since refractive index
profile looks like a pulse or step, this kind of fiber is called the STEP INDEX FIBER. This
structure is useful for analyzing propagation of light inside an optical fiber. Generally it is not
used in practice because data transfer rate in this fiber is the lowest.
Just as a small exercise we can ask, what kind of pulse broadening occurs in a step index
fiber if we do not use cladding?
So if we make a cladding-less optical fiber, its light launching efficiency is excellent but it
has hardly any bandwidth. Even an electrical cable is better than the optical fiber.
Important Conclusion: The cladding is an essential part of an optical fiber. It does not
just provide the mechanical support but increases the bandwidth of the fiber.
We can observe from the expression for pulse broadening that keeping all other
parameters constant.
Since , we get
BW .
Important: We can trade in the bandwidth for the length and vice versa. That is, we can
send low bit rate signals over long distances and high bit rate signals only over short
distances.
(b) The ray which is at a higher angle, should speed up and the ray which is along the axis of
the fiber should travel with
In this fiber we grade the refractive index profile of the core and consequently it is called
the graded index fiber.
A graded index fiber and the ray propagation is shown in the figure 6:
(c) If we taper the profile optimally, we get the dispersion reduction compared to that for a
step index fiber, even by a
factor of thousand. The data rate of a typical graded index fiber is typically 10 to 100 times
higher compared to a step index fiber.
Therefore, in practice, even for LANs, we use GIF (Graded Index Fiber) instead of SIF (Step
Index Fiber).
The light basically consists of wave fronts. A line perpendicular to a wave front is called the
ray. Light is an electromagnetic wave and when we say it travels like a ray it is a collection
of wavefronts which move.
Let us take an optical fiber with light rays propagating in it. The rays and the wave fronts
which are perpendicular to the rays, are as shown in figure 7:
Let us consider a phase front corresponding to the ray and passing through the point
. This phase front also meets the ray at point . In other words, the phase of the ray at
(just before the reflection) is same as that of the ray at point . That is to say that the
phase change corresponding to the distance added with the phase of the reflection
coefficient at points and should be a multiple of . This is what is called the condition
for the constructive interference.
Simplifying equations we get a condition for sustained propagation of light rays inside the
core as
It can be noted that for (i.e. the ray along the axis of the fiber), and the
condition is satisfied with for any value of .
As increases (either due to increase of the diameter of the core or refractive index
of the core, or decrease in wavelength) more values of satisfy the condition and therefore
have sustained propagation inside the fiber.
The above phase condition can be satisfied only by discrete rays entering the structure i.e.
rays at finite number of angles are accepted by the optical fiber. The ensemble of rays
entering at a specific angle from the axis of the fiber gives discrete optical intensity
distributions. These are called the modes of an optical fiber.
From the expression of the phase matching condition we find that as d increases, the
number of rays accepted by the optical fiber increases and as d decreases the number of
rays decreases.
Since the dispersion is due to presence of multiple rays (modes), if only one ray is made to
propagate inside the fiber, there is no dispersion. So if we take a value of small enough
such that it satisfies the phase condition only the lowest value of , only one mode will
propagate inside the fiber.
The lowest value of corresponds to the ray traveling along the axis of the fiber. In fact
this ray does not have any constraint on the size of the fiber etc, as it does not really go
through the total internal reflection at the core cladding boundary. This ray therefore always
propagates.
The optical fiber in which only one ray travels along the axis of fiber is called the single
mode optical fiber .
Single mode optical fiber is the best amongst the three types of fibers, namely the step
index fiber, GI fiber and the single mode fiber.
In a long distance communication, we use single mode optical fiber, whereas in LANs we
generally use graded index optical fiber.
Note: For single mode optical fiber however we have to use a source like laser because the
diameter of the fiber is very small and without a highly collimated beam, sufficient light can
not be launched inside the fiber.
SM
GRADED INDEX
STEP INDEX
Note: The Cladding Diameter for all types of fibers has been standardized to
(1) The ray model gives an impression that during total internal reflection the energy is
confined to the core only. However,
(2) The ray model does not speak of the discrete field patterns for propagation inside a fiber.
(3) The ray model breaks down when the core size becomes comparable to the wavelength of
light. The ray model
therefore is not quite justified for a SM fiber.
The limitations of the Ray model are overcome in the wave model discussed in the next
module.
Recap
In this lecture you have learnt the following
Simple ray model
Propagation of Meridional Rays
Dispersion
Different types of fibers
Limitations of the Ray-model
Congratulations, you have finished Module 2. To view the next lecture select it from the left
hand side menu of the page