Professional Documents
Culture Documents
Repair Instructions - On Vehicle
Repair Instructions - On Vehicle
2009 Saturn VUE - FWD | VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual | Transmission |
Automatic Transmission - 4T45-E | Repair Instructions - On Vehicle | Document ID: 2168532
Preliminary Procedures
Disconnect the transmission control module (TCM) electrical connector.
TCM
1 Procedure
Reprogram the TCM. Refer to Control Module References for programming and
setup information.
http://localhost:9001/si/showDoc.do?docSyskey=2168532&pubCellSyskey=122910&pub... 12/6/2010
Document ID: 2168535 Page 1 of 1
2009 Saturn VUE - FWD | VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual | Transmission |
Automatic Transmission - 4T45-E | Repair Instructions - On Vehicle | Document ID: 2168535
Preliminary Procedures
1. Remove the battery control module cover.
2. Disconnect the transmission control module (TCM) electrical connector.
TCM
1 Procedure
Reprogram the TCM. Refer to Control Module References for programming and
setup information.
http://localhost:9001/si/showDoc.do?docSyskey=2168535&pubCellSyskey=122910&pub... 12/6/2010
Document ID: 2125619 Page 1 of 1
2009 Saturn VUE - FWD | VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual | Transmission |
Automatic Transmission - 4T45-E | Repair Instructions - On Vehicle | Document ID: 2125619
Tighten
5.8 N·m (51 lb in)
Transaxle Auxiliary Fluid Pump Control Module
3
Tip
For programming setup information, refer to Control Module References.
http://localhost:9001/si/showDoc.do?docSyskey=2125619&pubCellSyskey=160971&pub... 12/6/2010
Document ID: 2168539 Page 1 of 1
2009 Saturn VUE - FWD | VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual | Transmission |
Automatic Transmission - 4T45-E | Repair Instructions - On Vehicle | Document ID: 2168539
Preliminary Procedures
1. Remove the front floor console extension panel. Refer to Front Floor Console Extension
Panel Replacement.
2. Disconnect the range select cable from range select lever.
3. Disconnect the range select lever electrical connector.
Automatic Transmission Range Select Lever Nut (Qty: 4)
Tighten
8 N·m (71 lb in)
2 Automatic Transmission Range Select Lever
http://localhost:9001/si/showDoc.do?docSyskey=2168539&pubCellSyskey=3504&pubObj... 12/6/2010
Document ID: 2168543 Page 1 of 1
2009 Saturn VUE - FWD | VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual | Transmission |
Automatic Transmission - 4T45-E | Repair Instructions - On Vehicle | Document ID: 2168543
Preliminary Procedures
Remove the automatic transmission control. Refer to Transmission Control Replacement.
Transmission Control Bracket Bolt (Qty: 2)
Tighten
25 N·m (18 lb ft)
Transmission Control Bracket Nut (Qty: 4)
2
Tighten
25 N·m (18 lb ft)
3 Transmission Control Bracket
http://localhost:9001/si/showDoc.do?docSyskey=2168543&pubCellSyskey=160353&pub... 12/6/2010
Document ID: 1878678 Page 1 of 3
2009 Saturn VUE - FWD | VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual | Transmission |
Automatic Transmission - 4T45-E | Repair Instructions - On Vehicle | Document ID: 1878678
1. Disconnect the range select cable (2) from the range select lever (1).
2. Release the range select cable retaining clip (3) and remove the cable from the range select
cable bracket (4).
3. Remove the front floor console extension panel. Refer to Front Floor Console Extension Panel
Replacement .
http://localhost:9001/si/showDoc.do?docSyskey=1878678&pubCellSyskey=66762&pubO... 12/6/2010
Document ID: 1878678 Page 2 of 3
4. Remove the range select cable (2) from the automatic transmission range select lever pin.
5. Remove the range select cable (1) from the automatic transmission range select lever
housing.
6. Remove the range select cable grommet (1) from the cowl.
7. Remove the range select cable from the vehicle.
Installation Procedure
1. Install the range select cable to the vehicle through the cowl and the carpet.
2. Install the range select cable grommet (1) in the cowl.
http://localhost:9001/si/showDoc.do?docSyskey=1878678&pubCellSyskey=66762&pubO... 12/6/2010
Document ID: 1878678 Page 3 of 3
3. Install the range select cable (1) to the automatic transmission range select lever housing.
4. Install the range select cable (2) to the automatic transmission range select lever pin.
5. Install the front floor console extension panel. Refer to Front Floor Console Extension Panel
Replacement .
6. Install the range select cable to the range select cable bracket (4). Ensure the range select
cable retaining clip (3) is secured in the bracket.
7. Connect the range select cable (2) to the range select lever (1).
8. Adjust the cable. Refer to Shift Control Cable Adjustment .
http://localhost:9001/si/showDoc.do?docSyskey=1878678&pubCellSyskey=66762&pubO... 12/6/2010
Document ID: 2168547 Page 1 of 2
2009 Saturn VUE - FWD | VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual | Transmission |
Automatic Transmission - 4T45-E | Repair Instructions - On Vehicle | Document ID: 2168547
Preliminary Procedures
1. Apply the parking brake.
2. Remove the front floor console extension panel. Refer to Front Floor Console Extension
Panel Replacement.
3. Disconnect the transmission tap up/tap down switch electrical connector.
Automatic Transmission Control Lever Knob Bezel
Tip
• Removal: carefully insert a small flat-bladed tool on the right and left sides of
the bezel (1) between the bezel and the shift knob. Apply careful downward
1 pressure to the bezel to separate the bezel from the shift knob. The bezel will
drop down approximately 13.0 mm (0.5 in) exposing the shift knob
screws (2).
• Installation: Lift the bezel (1) up to the shift knob until a click sound is heard
indicating the bezel is secured to the shift knob.
http://localhost:9001/si/showDoc.do?docSyskey=2168547&pubCellSyskey=117646&pub... 12/6/2010
Document ID: 2168547 Page 2 of 2
Tip
Loosen the shift control knob screws approximately 4-5 turns. It is not necessary to
fully remove the screws from the shift control knob.
2
Tighten
Tighten the screw to 1.5 N·m (13 lb in).
http://localhost:9001/si/showDoc.do?docSyskey=2168547&pubCellSyskey=117646&pub... 12/6/2010
Document ID: 1878286 Page 1 of 1
2009 Saturn VUE - FWD| VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual | Transmission |
Automatic Transmission - 4T45-E | Repair Instructions - On Vehicle | Document ID: 1878286
Preliminary Procedures
1. Remove the automatic transmission control lever knob. Refer to Transmission Control
Lever Knob Replacement.
2. Remove the control position indicator bulb from the automatic transmisson control
indicator.
1 Automatic Transmisson Control Indicator
http://localhost:9001/si/showDoc.do?docSyskey=1878286&pubCellSyskey=117650&pub... 12/6/2010
Document ID: 2168552 Page 1 of 3
2009 Saturn VUE - FWD | VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual | Transmission |
Automatic Transmission - 4T45-E | Repair Instructions - On Vehicle | Document ID: 2168552
1. Disconnect the range select cable (2) from the range select lever (1).
2. Release the range select cable retaining clip (3) and remove the cable from the range select
cable bracket (4).
http://localhost:9001/si/showDoc.do?docSyskey=2168552&pubCellSyskey=164188&pub... 12/6/2010
Document ID: 2168552 Page 2 of 3
Installation Procedure
1. Install the transmission range select lever (3) to the transmission manual shaft (1).
2. Install the transmission range select lever nut (2) and tighten to 35 N·m (26 lb ft).
3. Install the range select cable to the range select cable bracket (4). Ensure the cable retaining
http://localhost:9001/si/showDoc.do?docSyskey=2168552&pubCellSyskey=164188&pub... 12/6/2010
Document ID: 2168552 Page 3 of 3
http://localhost:9001/si/showDoc.do?docSyskey=2168552&pubCellSyskey=164188&pub... 12/6/2010
Document ID: 1878517 Page 1 of 3
2009 Saturn VUE - FWD | VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual | Transmission |
Automatic Transmission - 4T45-E | Repair Instructions - On Vehicle | Document ID: 1878517
2. Release the shift control cable adjustment lock cover retaining tab (1).
3. Slide the shift control cable adjustment lock cover (1) back exposing the adjustment lock.
http://localhost:9001/si/showDoc.do?docSyskey=1878517&pubCellSyskey=122592&pub... 12/6/2010
Document ID: 1878517 Page 2 of 3
7. Slide the shift control cable adjustment lock cover (1) over the adjustment lock.
http://localhost:9001/si/showDoc.do?docSyskey=1878517&pubCellSyskey=122592&pub... 12/6/2010
Document ID: 1878517 Page 3 of 3
8. Ensure the shift control cable adjustment lock cover (1) is securely latched on the
adjustment lock.
9. Inspect the operation of the starting system with the shift lever in each position. The engine
should only crank when the lever is in the PARK or NEUTRAL position.
http://localhost:9001/si/showDoc.do?docSyskey=1878517&pubCellSyskey=122592&pub... 12/6/2010
Document ID: 2168180 Page 1 of 3
2009 Saturn VUE - FWD | VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual | Transmission |
Automatic Transmission - 4T45-E | Repair Instructions - On Vehicle | Document ID: 2168180
Removal Procedure
1. Remove the automatic transmission range select lever. Refer to Automatic Transmission
Range Selector Lever Replacement.
2. Disconnect the PNP switch electrical connector (3) from the PNP switch (4).
3. Remove the PNP switch bolt (2) and stud (1).
4. Remove the PNP switch (4) from the transaxle.
Installation Procedure
http://localhost:9001/si/showDoc.do?docSyskey=2168180&pubCellSyskey=3499&pubObj... 12/6/2010
Document ID: 2168180 Page 2 of 3
Note: After adjusting the switch, verify the engine only starts in Park or Neutral. If the
engine starts in any other position, adjust the switch.
5. Insert the J 41545 as shown and rotate the PNP switch until the tool drops onto position.
http://localhost:9001/si/showDoc.do?docSyskey=2168180&pubCellSyskey=3499&pubObj... 12/6/2010
Document ID: 2168180 Page 3 of 3
6. Tighten the PNP switch bolt and stud to 20 N·m (15 lb ft).
7. Remove the alignment tool.
8. Install the automatic transmission range select lever. Refer to Automatic Transmission Range
Selector Lever Replacement.
http://localhost:9001/si/showDoc.do?docSyskey=2168180&pubCellSyskey=3499&pubObj... 12/6/2010
Document ID: 2168183 Page 1 of 3
2009 Saturn VUE - FWD | VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual | Transmission |
Automatic Transmission - 4T45-E | Repair Instructions - On Vehicle | Document ID: 2168183
Adjustment
1. Disconnect the transaxle range switch electrical connectors from the switch.
2. Remove the shift control cable from the transaxle range switch lever.
http://localhost:9001/si/showDoc.do?docSyskey=2168183&pubCellSyskey=117651&pub... 12/6/2010
Document ID: 2168183 Page 2 of 3
6. Insert the J 41545 as shown and rotate the switch until the tool drops onto position.
http://localhost:9001/si/showDoc.do?docSyskey=2168183&pubCellSyskey=117651&pub... 12/6/2010
Document ID: 2168183 Page 3 of 3
Note: After adjusting the switch, verify the engine only starts in Park or Neutral. If the
engine starts in any other position, adjust the switch.
9. Install the transaxle range switch lever and nut and tighten to 35 N·m (26 lb ft)
10. Connect the transaxle range switch electrical connectors to the switch.
11. Install the shift control cable to transaxle range switch lever and verify proper operation.
http://localhost:9001/si/showDoc.do?docSyskey=2168183&pubCellSyskey=117651&pub... 12/6/2010
Document ID: 2168186 Page 1 of 4
2009 Saturn VUE - FWD | VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual | Transmission |
Automatic Transmission - 4T45-E | Repair Instructions - On Vehicle | Document ID: 2168186
Caution: When removing the oil pan bolts, be careful not to damage the oil pan sealing
surfaces. Such damage may result in oil leaks in this area.
3. Remove the oil pan bolts from only the front and the sides.
4. Loosen the rear oil pan bolts about 4 turns.
5. Lightly tap the oil pan with a rubber mallet or pry in order to allow the fluid to drain.
6. Remove the remaining oil pan bolts.
http://localhost:9001/si/showDoc.do?docSyskey=2168186&pubCellSyskey=3455&pubObj... 12/6/2010
Document ID: 2168186 Page 2 of 4
Installation Procedure
1. Clean and inspect the oil pan for dents or damage. Dry the oil pan before installation.
http://localhost:9001/si/showDoc.do?docSyskey=2168186&pubCellSyskey=3455&pubObj... 12/6/2010
Document ID: 2168186 Page 3 of 4
2. Install the oil pan gasket. Use a new gasket if the sealing ribs are damaged.
http://localhost:9001/si/showDoc.do?docSyskey=2168186&pubCellSyskey=3455&pubObj... 12/6/2010
Document ID: 2168186 Page 4 of 4
4. Install the oil pan attaching bolts and tighten to 12 N·m (106 lb in).
5. Lower the vehicle.
6. Fill the transmission.
7. Inspect the transmission fluid level. Refer to Transmission Fluid Check
8. Inspect the oil pan gasket for leaks.
Caution: Transmission Auxiliary Pump Priming must be performed after any service
procedure is performed on the transmission that involves the draining of and refill of
transmission fluid. Failure to perform the Transmission Auxiliary Pump Priming will result in
damage to the auxiliary pump and possible damage to the transmission.
9. Using a scan tool, prime the Transmission Auxiliary Pump, if equipped with 2.4L (LAT).
http://localhost:9001/si/showDoc.do?docSyskey=2168186&pubCellSyskey=3455&pubObj... 12/6/2010
Document ID: 680760 Page 1 of 2
2009 Saturn VUE - FWD | VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual | Transmission |
Automatic Transmission - 4T45-E | Repair Instructions - On Vehicle | Document ID: 680760
Removal Procedure
1. Remove transaxle oil pan. Refer to Oil Pan Replacement .
2. Remove the oil filter. Use a long screwdriver in order to pry the oil filter neck out of the seal.
3. Check the oil filter seal for damage or wear.
4. As needed, remove the seal using the J 6125-1B and the J 23129 .
Installation Procedure
http://localhost:9001/si/showDoc.do?docSyskey=680760&pubCellSyskey=3662&pubObj... 12/6/2010
Document ID: 680760 Page 2 of 2
1. Install a new seal, as needed. Before installing, coat the new seal with a small amount of
petroleum jelly.
2. Install a new filter into the case.
3. Install transaxle oil pan. Refer to Oil Pan Replacement .
http://localhost:9001/si/showDoc.do?docSyskey=680760&pubCellSyskey=3662&pubObj... 12/6/2010
Document ID: 2168188 Page 1 of 2
2009 Saturn VUE - FWD | VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual | Transmission |
Automatic Transmission - 4T45-E | Repair Instructions - On Vehicle | Document ID: 2168188
2. Remove the vehicle speed sensor (VSS) electrical connector (1) from the VSS.
3. Remove the VSS electrical harness retainer (2) from the VSS.
4. Remove the retaining stud and the VSS. Pull straight out in order to avoid damage to the
case.
© 2010 General Motors Corporation. All rights reserved.
http://localhost:9001/si/showDoc.do?docSyskey=2168188&pubCellSyskey=3454&pubObj... 12/6/2010
Document ID: 2168188 Page 2 of 2
Installation Procedure
1. Clean and dry the VSS.
2. Install the VSS and the retaining stud to 12 N·m (97 lb in).
http://localhost:9001/si/showDoc.do?docSyskey=2168188&pubCellSyskey=3454&pubObj... 12/6/2010
Document ID: 2168195 Page 1 of 3
2009 Saturn VUE - FWD | VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual | Transmission |
Automatic Transmission - 4T45-E | Repair Instructions - On Vehicle | Document ID: 2168195
2. Remove the 3 low and reverse band servo cover bolts, the servo, and the spring.
Disassembly Procedure
http://localhost:9001/si/showDoc.do?docSyskey=2168195&pubCellSyskey=3663&pubObj... 12/6/2010
Document ID: 2168195 Page 2 of 3
1. Remove the piston pin assembly (67-70) from the servo cover (73).
2. Remove the snap ring (70) from the servo pin (67).
3. Remove the piston (69) and the servo cushion spring (68), or springs (139), from the servo
pin (67).
4. Remove the servo piston seals (71, 72) from the cover (73).
5. Discard the servo piston seals (71 and 72).
6. Inspect all the components for damage.
7. Inspect the fluid feed holes for the proper opening.
8. Inspect the bolt hole threads for debris or stripping.
9. Inspect the seal grooves for damage.
10. Clean and dry each component.
Assembly Procedure
1. Assemble the servo cushion spring (68), or springs (139), and the servo piston (69) onto the
servo pin (67).
2. Install the snap ring onto the servo pin (67) in order to retain the servo cushion springs (68)
and the servo piston (69).
3. Assemble the new seals (71, 72) onto the servo piston (69) and the servo cover (73).
4. Assemble the servo piston assembly (67-70) into the servo cover (73). Lubricate the piston
seals with transmission fluid in order to aid in assembly.
Installation Procedure
Caution: Refer to Fastener Caution in the Preface section.
http://localhost:9001/si/showDoc.do?docSyskey=2168195&pubCellSyskey=3663&pubObj... 12/6/2010
Document ID: 2168195 Page 3 of 3
1. Install the low and the reverse band servo cover bolts and tighten to 12 N·m (106 lb in).
2. Install the oil feed pipe. Refer to Oil Feed Pipes Replacement.
Resetting the TAP values using a scan tool will erase all learned values in all cells. As a result,
the engine control module (ECM), powertrain control module (PCM) or transmission control
module (TCM) will need to relearn TAP values. Transmission performance may be affected as
new TAP values are learned.
http://localhost:9001/si/showDoc.do?docSyskey=2168195&pubCellSyskey=3663&pubObj... 12/6/2010
Document ID: 2168199 Page 1 of 4
2009 Saturn VUE - FWD | VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual | Transmission |
Automatic Transmission - 4T45-E | Repair Instructions - On Vehicle | Document ID: 2168199
3. Remove the two intermediate/4th servo cover bolts, the servo and the spring.
Disassemble Procedure
http://localhost:9001/si/showDoc.do?docSyskey=2168199&pubCellSyskey=3664&pubObj... 12/6/2010
Document ID: 2168199 Page 2 of 4
1. Remove the piston and pin assembly (76 and 77) from the servo cover (80).
2. Remove the snap ring (70) from the servo pin (76).
3. Remove the piston (77) and the servo cushion springs (68) from the servo pin (76).
4. Remove the servo piston seals (78, 79) from the servo cover (80).
5. Discard the servo piston seals (78 and 79). Do not reuse the servo piston seals.
Assemble Procedure
http://localhost:9001/si/showDoc.do?docSyskey=2168199&pubCellSyskey=3664&pubObj... 12/6/2010
Document ID: 2168199 Page 3 of 4
1. Install the servo cushion springs (68) and the servo piston (77) onto the servo pin (76).
2. Install the snap ring (70) onto the servo pin (76) in order to retain the springs (68) and
piston (77).
3. Install the new seals (78 and 79) onto the servo piston (77) and the servo cover (80).
4. Install the servo piston assembly into the servo cover (80). Lubricate the piston seals with
transmission fluid in order to aid in assembly.
Installation Procedure
Caution: Refer to Fastener Caution in the Preface section.
1. Install the intermediate/4th band servo piston spring, the servo and the servo cover bolts.
http://localhost:9001/si/showDoc.do?docSyskey=2168199&pubCellSyskey=3664&pubObj... 12/6/2010
Document ID: 2168199 Page 4 of 4
2. Install the filter and the pan. Refer to Automatic Transmission Fluid Filter and Seal
Replacement.
3. Lower the vehicle.
4. Fill the transmission with DEXRON® VI fluid.
5. Inspect the transmission oil level. Refer to Transmission Fluid Check.
Resetting the TAP values using a scan tool will erase all learned values in all cells. As a result,
the engine control module (ECM), powertrain control module (PCM) or transmission control
module (TCM) will need to relearn TAP values. Transmission performance may be affected as
new TAP values are learned.
http://localhost:9001/si/showDoc.do?docSyskey=2168199&pubCellSyskey=3664&pubObj... 12/6/2010
Document ID: 2135098 Page 1 of 2
2009 Saturn VUE - FWD | VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual | Transmission |
Automatic Transmission - 4T45-E | Repair Instructions - On Vehicle | Document ID: 2135098
Note: Do not remove the upper and lower transaxle oil cooler fittings from the radiator at
the same time other wise the transaxle oil cooler will fall inside the radiator end tank.
Installation Procedure
1. Inspect the new O-ring seals for cracks, cuts or damage. Replace if necessary.
http://localhost:9001/si/showDoc.do?docSyskey=2135098&pubCellSyskey=163423&pub... 12/6/2010
Document ID: 2135098 Page 2 of 2
Note: The correct thread engagement is critical. Cross-threaded fittings can achieve proper
tightness and still leak.
2. Install the oil cooler fitting to the radiator and tighten to 38 N·m (28 lb ft).
3. Install the transaxle oil cooler hoses to the oil cooler fittings on the radiator. Refer to
Transmission Fluid Cooler Hose Replacement.
4. Fill the cooling system. Refer to Cooling System Draining and Filling.
5. Adjust the transmission fluid level.
6. Inspect for fluid leaks.
http://localhost:9001/si/showDoc.do?docSyskey=2135098&pubCellSyskey=163423&pub... 12/6/2010
Document ID: 1402449 Page 1 of 7
2009 Saturn VUE - FWD | VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual | Transmission |
Automatic Transmission - 4T45-E | Repair Instructions - On Vehicle | Document ID: 1402449
Important: Perform the following procedure when removing the retaining rings and cooler
lines from the quick connect fittings located on the radiator and/or the transmission.
1. Pull the plastic cap back from the quick connect fitting and down along the cooler line about
5 cm (2 in).
2. Using a bent-tip screwdriver, pull on one of the open ends of the retaining ring in order to
rotate the retaining ring around the quick connect fitting until the retaining ring is out of
position and can be completely removed.
3. Remove the retaining ring from the quick connect fitting.
4. Discard the retaining ring.
http://localhost:9001/si/showDoc.do?docSyskey=1402449&pubCellSyskey=80909&pubO... 12/6/2010
Document ID: 1402449 Page 2 of 7
5. Pull the cooler line straight out from the quick connect fitting.
Installation Procedure
Important:
• Do not reuse any of the existing oil lines or oil line fittings if there is excessive
corrosion.
• Do not reuse any of the existing retaining rings that were removed from the existing
quick connect fittings. Install new retaining rings.
• Ensure the following procedures are performed when installing the new retaining rings
onto the fittings.
1. Install a new retaining ring into the quick connect fitting using the following procedure:
http://localhost:9001/si/showDoc.do?docSyskey=1402449&pubCellSyskey=80909&pubO... 12/6/2010
Document ID: 1402449 Page 3 of 7
2. Hook one of the open ends of the retaining ring in one of the slots in the quick connect
fitting.
3. Rotate the retaining ring around the fitting until the retaining ring is positioned with all three
ears through the three slots on the fitting.
4. Do not install the new retaining ring onto the fitting by pushing the retaining ring.
http://localhost:9001/si/showDoc.do?docSyskey=1402449&pubCellSyskey=80909&pubO... 12/6/2010
Document ID: 1402449 Page 4 of 7
5. Ensure that the three retaining ring ears are seen from inside the fitting and that the
retaining ring moves freely in the fitting slots.
http://localhost:9001/si/showDoc.do?docSyskey=1402449&pubCellSyskey=80909&pubO... 12/6/2010
Document ID: 1402449 Page 5 of 7
8. Do not use the plastic cap on the cooler line in order to install the cooler line into the fitting.
9. Pull back sharply on the cooler line in order to ensure that the cooler line is fastened into the
quick connect fitting.
Important: Do not manually depress the retaining clip when installing the plastic cap.
10. Position (snap) the plastic cap onto the fitting. Do not manually depress the retaining ring
when installing the plastic cap onto the quick connect fitting.
11. Ensure that the plastic cap is fully seated against the fitting.
http://localhost:9001/si/showDoc.do?docSyskey=1402449&pubCellSyskey=80909&pubO... 12/6/2010
Document ID: 1402449 Page 6 of 7
12. Ensure that no gap is present between the cap and the fitting.
13. Ensure that the yellow identification band on the tube is hidden within the quick connect
fitting.
http://localhost:9001/si/showDoc.do?docSyskey=1402449&pubCellSyskey=80909&pubO... 12/6/2010
Document ID: 1402449 Page 7 of 7
http://localhost:9001/si/showDoc.do?docSyskey=1402449&pubCellSyskey=80909&pubO... 12/6/2010
Document ID: 2154151 Page 1 of 2
2009 Saturn VUE - FWD | VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual | Transmission |
Automatic Transmission - 4T45-E | Repair Instructions - On Vehicle | Document ID: 2154151
Removal Procedure
Caution: Allow sufficient clearance around the transaxle oil cooler pipes and around the
hoses to prevent damage or wear which may cause fluid loss.
2. Remove the upper transaxle oil cooler pipe fitting at the radiator.
3. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle.
4. Position a drain pan under the transaxle cooler pipes.
5. Remove the transaxle oil cooler pipe retaining nut from the transaxle.
6. Remove the transaxle oil cooler pipe from the transaxle.
7. Remove the lower transaxle oil cooler pipe fitting at the radiator.
8. Remove the transaxle oil cooler pipe retaining clip from the radiator.
9. Remove the transaxle oil cooler pipes from the vehicle.
Installation Procedure
http://localhost:9001/si/showDoc.do?docSyskey=2154151&pubCellSyskey=3660&pubObj... 12/6/2010
Document ID: 2154151 Page 2 of 2
Note: The correct thread engagement is critical. Crossthreaded fittings can achieve proper
tightness value and still leak.
3. Install the lower transaxle oil cooler pipe fitting to the radiator and tighten the fitting to
16 N·m (12 lb ft).
4. Install the transaxle oil cooler pipes to the transaxle.
5. Install the transaxle oil cooler pipe retaining nut and tighten to 4 N·m (27 lb in).
6. Lower the vehicle.
7. Install the upper transaxle oil cooler pipe fitting to the radiator and tighten the fitting to
16 N·m (12 lb ft).
8. Install the battery box. Refer to Battery Tray Replacement.
Caution: Do NOT overfill the transaxle. The overfilling of the transaxle causes foaming, loss
of fluid, shift complaints, and possible damage to the transaxle.
http://localhost:9001/si/showDoc.do?docSyskey=2154151&pubCellSyskey=3660&pubObj... 12/6/2010
Document ID: 2168201 Page 1 of 2
2009 Saturn VUE - FWD | VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual | Transmission |
Automatic Transmission - 4T45-E | Repair Instructions - On Vehicle | Document ID: 2168201
Preliminary Procedures
1. Raise the vehicle. Refer to Lifting and Jacking the Vehicle.
2. Remove the front transaxle mount. Refer to Transmission Front Mount Replacement.
3. Remove the auxiliary fluid pump. Refer to Auxiliary Fluid Pump Replacement.
Transaxle Auxiliary Fluid Pump Inlet Pipe Bolt (Qty: 2)
Tighten
25 N·m (18 lb ft)
Caution: Transmission Auxiliary Pump Priming must be performed after any service
procedure is performed on the transmission that involves the draining of and refill of
2
transmission fluid. Failure to perform the Transmission Auxiliary Pump Priming will
result in damage to the auxiliary pump and possible damage to the transmission.
http://localhost:9001/si/showDoc.do?docSyskey=2168201&pubCellSyskey=160972&pub... 12/6/2010
Document ID: 2168201 Page 2 of 2
Prime the auxiliary fluid pump. Refer to Auxiliary Fluid Pump Priming
http://localhost:9001/si/showDoc.do?docSyskey=2168201&pubCellSyskey=160972&pub... 12/6/2010
Document ID: 2168204 Page 1 of 2
2009 Saturn VUE - FWD | VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual | Transmission |
Automatic Transmission - 4T45-E | Repair Instructions - On Vehicle | Document ID: 2168204
Preliminary Procedures
1. Raise the vehicle. Refer to Lifting and Jacking the Vehicle.
2. Remove the front transaxle mount. Refer to Transmission Front Mount Replacement.
3. Remove the auxiliary fluid pump. Refer to Auxiliary Fluid Pump Replacement.
Transaxle Auxiliary Fluid Pump Outlet Pipe Bolt
Tighten
25 N·m (18 lb ft)
Caution: Transmission Auxiliary Pump Priming must be performed after any service
procedure is performed on the transmission that involves the draining of and refill of
2
transmission fluid. Failure to perform the Transmission Auxiliary Pump Priming will
result in damage to the auxiliary pump and possible damage to the transmission.
http://localhost:9001/si/showDoc.do?docSyskey=2168204&pubCellSyskey=160973&pub... 12/6/2010
Document ID: 2168204 Page 2 of 2
Prime the auxiliary fluid pump. Refer to Auxiliary Fluid Pump Priming
Tighten
22 N·m (16 lb ft)
http://localhost:9001/si/showDoc.do?docSyskey=2168204&pubCellSyskey=160973&pub... 12/6/2010
Document ID: 2125615 Page 1 of 2
2009 Saturn VUE - FWD | VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual | Transmission |
Automatic Transmission - 4T45-E | Repair Instructions - On Vehicle | Document ID: 2125615
Preliminary Procedures
1. Remove the generator control module and battery tray. Refer to Generator Control
Module Replacement.
2. Disconnect the fluid pump inlet pipe from the auxiliary fluid pump. Refer to Auxiliary
Fluid Pump Inlet Pipe Replacement.
3. Disconnect the fluid pump outlet pipe from the auxiliary fluid pump. Refer to Auxiliary
Fluid Pump Outlet Pipe Replacement.
4. Disconnect the electrical connector from the auxiliary fluid pump.
Transaxle Auxiliary Fluid Pump Bolt (Qty: 4)
Tighten
25 N·m (18 lb ft)
Transaxle Auxiliary Fluid Pump
Caution: Transmission Auxiliary Pump Priming must be performed after any service
procedure is performed on the transmission that involves the draining of and refill of
transmission fluid.©Failure to perform
2010 General the Transmission
Motors Corporation. All rights Auxiliary
reserved. Pump Priming will
http://localhost:9001/si/showDoc.do?docSyskey=2125615&pubCellSyskey=160974&pub... 12/6/2010
Document ID: 2125615 Page 2 of 2
result in damage to the auxiliary pump and possible damage to the transmission.
2 Procedure
Prime the auxiliary fluid pump. Refer to Auxiliary Fluid Pump Priming
http://localhost:9001/si/showDoc.do?docSyskey=2125615&pubCellSyskey=160974&pub... 12/6/2010
Document ID: 1859233 Page 1 of 1
2009 Saturn VUE - FWD | VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual | Transmission |
Automatic Transmission - 4T45-E | Repair Instructions - On Vehicle | Document ID: 1859233
http://localhost:9001/si/showDoc.do?docSyskey=1859233&pubCellSyskey=163344&pub... 12/6/2010
Document ID: 2168207 Page 1 of 3
2009 Saturn VUE - FWD | VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual | Transmission |
Automatic Transmission - 4T45-E | Repair Instructions - On Vehicle | Document ID: 2168207
http://localhost:9001/si/showDoc.do?docSyskey=2168207&pubCellSyskey=3667&pubObj... 12/6/2010
Document ID: 2168207 Page 2 of 3
6. Remove the eight lo and the reverse band oil pipe assembly seals.
7. Inspect the oil feed pipes for plugged passages, bent pipes, or cracks.
8. Inspect the oil feed pipe seal rings. Verify the proper location of the seal rings. Replace the
seal rings if these are cut, swelled or damaged.
Installation Procedure
1. Install the eight lo and the reverse band oil pipe assembly seals.
2. Install the lo and the reverse band oil feed pipe assembly onto the transmission.
http://localhost:9001/si/showDoc.do?docSyskey=2168207&pubCellSyskey=3667&pubObj... 12/6/2010
Document ID: 2168207 Page 3 of 3
3. Hand start the bolts that attach the oil feed pipe assembly to the transmission.
4. Install the transmission oil filter assembly. Refer to Automatic Transmission Fluid Filter and
Seal Replacement.
Resetting the TAP values using a scan tool will erase all learned values in all cells. As a result,
the engine control module (ECM), powertrain control module (PCM) or transmission control
module (TCM) will need to relearn TAP values. Transmission performance may be affected as
new TAP values are learned.
http://localhost:9001/si/showDoc.do?docSyskey=2168207&pubCellSyskey=3667&pubObj... 12/6/2010
Document ID: 2168218 Page 1 of 4
2009 Saturn VUE - FWD | VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual | Transmission |
Automatic Transmission - 4T45-E | Repair Instructions - On Vehicle | Document ID: 2168218
Removal Procedure
1. Disconnect the air cleaner outlet duct from the intake plenum. Refer to Air Cleaner Outlet
Duct Replacement.
2. Remove the frame. Refer to Frame Replacement.
3. Remove the left front splash shield. Refer to Engine Splash Shield Replacement.
4. Remove the left wheel drive shaft from the transmission. Refer to Front Wheel Drive Shaft
Replacement.
5. Remove the left transmission mount. Refer to Transmission Mount Replacement - Left Side.
6. Remove the park neutral position (PNP) switch. Refer to Park/Neutral Position Switch
Replacement.
http://localhost:9001/si/showDoc.do?docSyskey=2168218&pubCellSyskey=3668&pubObj... 12/6/2010
Document ID: 2168218 Page 2 of 4
11. Remove the transmission side cover bolts (3) and studs (4).
12. Separate the case side cover (1) from the transmission case at the dowel pin locations (45)
to prevent damage to the sealing surfaces.
13. Remove the transmission side cover (1).
14. Remove the two side cover gaskets (5 and 6) if they do not remain with the side cover.
15. Remove the thrust washer (7) if it does not remain with the side cover.
Caution: Do not damage the case bore when removing the axle seal.
16. Remove the side cover axle seal (2). Use the handle end of a hammer.
17. Remove the sleeve from the output axle shaft. Refer to Front Wheel Drive Shaft Seal and
Output Shaft Sleeve Replacement - Left Side.
http://localhost:9001/si/showDoc.do?docSyskey=2168218&pubCellSyskey=3668&pubObj... 12/6/2010
Document ID: 2168218 Page 3 of 4
Installation Procedure
1. Inspect the side cover for cracks or damage to the seal grooves and mounting bosses.
2. Inspect the side cover seals for damage. The side cover seals are reusable if not damaged.
3. Thoroughly clean the side cover and the side cover seals.
4. Clean and dry the seal grooves and the axle seal bore.
5. Install the side cover gaskets (5 and 6) into the grooves on the side cover (1).
6. Retain the seals with J 36850 or equivalent.
7. Install the side cover to drive sprocket thrust washer (7) onto the side cover.
8. Retain the thrust washer with J 36850 or equivalent.
http://localhost:9001/si/showDoc.do?docSyskey=2168218&pubCellSyskey=3668&pubObj... 12/6/2010
Document ID: 2168218 Page 4 of 4
10. Install the transmission side cover bolts (3) and studs (4) and tighten to 28 N·m (22 lb ft).
11. Install the output axle seal and sleeve. Refer to Front Wheel Drive Shaft Seal and Output
Shaft Sleeve Replacement - Left Side.
12. Lower the vehicle.
13. Using the engine support fixture, raile the engine and transmission.
14. Install the shift cable bracket bolt (3) and tighten to 22 N·m (16 lb ft).
15. Install the PNP switch. Refer to Park/Neutral Position Switch Replacement.
16. Install the transmission mount. Refer to Transmission Mount Replacement - Left Side.
17. If equipped with 2.4L (LAT), install the auxiliary fluid pump. Refer to Auxiliary Fluid Pump
Replacement.
18. Raise the vehicle. Refer to Lifting and Jacking the Vehicle.
19. Install the left wheel drive shaft to the transmission. Refer to Front Wheel Drive Shaft
Replacement.
20. Install the left front splash shield. Refer to Engine Splash Shield Replacement.
21. Install the frame. Refer to Frame Replacement.
22. Connect the air cleaner outlet duct to the intake plenum. Refer to Air Cleaner Outlet Duct
Replacement.
23. Fill the transmission. Refer to Approximate Fluid Capacities.
Caution: Transmission Auxiliary Pump Priming must be performed after any service
procedure is performed on the transmission that involves the draining of and refill of
transmission fluid. Failure to perform the Transmission Auxiliary Pump Priming will result in
damage to the auxiliary pump and possible damage to the transmission.
24. If equipped with 2.4L (LAT), using a scan tool, prime the transmission auxiliary pump.
http://localhost:9001/si/showDoc.do?docSyskey=2168218&pubCellSyskey=3668&pubObj... 12/6/2010
Document ID: 703298 Page 1 of 2
2009 Saturn VUE - FWD | VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual | Transmission |
Automatic Transmission - 4T45-E | Repair Instructions - On Vehicle | Document ID: 703298
2. Remove the side cover gaskets (5 and 6) and the thrust washer (7) from the side cover (1).
3. Inspect the side cover for cracks or damage to the seal grooves and mounting bosses.
4. Inspect the side cover seals for damage. The side cover seals are reusable if not damaged.
5. Thoroughly clean the side cover and the side cover seals. Clean and dry the seal grooves and
the axle seal bore.
Installation Procedure
http://localhost:9001/si/showDoc.do?docSyskey=703298&pubCellSyskey=3745&pubObj... 12/6/2010
Document ID: 703298 Page 2 of 2
1. Install the side cover gaskets (5 and 6) into the grooves on the side cover (1).
2. Retain the seals with J 36850 or equivalent .
3. Install the side cover to drive sprocket thrust washer (7) onto the side cover.
4. Retain the thrust washer with J 36850 or equivalent.
5. Install the transmission side cover. Refer to Control Valve Body Cover Replacement .
http://localhost:9001/si/showDoc.do?docSyskey=703298&pubCellSyskey=3745&pubObj... 12/6/2010
Document ID: 804002 Page 1 of 2
2009 Saturn VUE - FWD | VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual | Transmission |
Automatic Transmission - 4T45-E | Repair Instructions - On Vehicle | Document ID: 804002
Removal Procedure
1. Remove the transmission side cover. Refer to Control Valve Body Cover Replacement.
2. Remove the control valve body. Refer to Control Valve Body Replacement.
3. Push the J 41101 onto the pass-through connector from the outside of the transmission case
in order to compress the pass-through connector's retaining tabs.
4. With the retaining tabs compressed, use a screwdriver in order to remove the pass-through
connector through the inside of the transmission case.
5. Remove the wiring harness (11).
Installation Procedure
http://localhost:9001/si/showDoc.do?docSyskey=804002&pubCellSyskey=71416&pubObj... 12/6/2010
Document ID: 804002 Page 2 of 2
Important: The 1-2 shift solenoids wires are red and light green. The 2-3 shift solenoid
wires are red and yellow.
Resetting the TAP values using a scan tool will erase all learned values in all cells. As a result,
the engine control module (ECM), powertrain control module (PCM) or transmission control
module (TCM) will need to relearn TAP values. Transmission performance may be affected as
new TAP values are learned.
http://localhost:9001/si/showDoc.do?docSyskey=804002&pubCellSyskey=71416&pubObj... 12/6/2010
Document ID: 803999 Page 1 of 2
2009 Saturn VUE - FWD | VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual | Transmission |
Automatic Transmission - 4T45-E | Repair Instructions - On Vehicle | Document ID: 803999
1. Remove the transmission side cover. Refer to Control Valve Body Cover Replacement
2. Remove the TCC solenoid retainer clip (304), the TCC solenoid (335), with two O-rings (337,
338), and screen, the TCC regulated apply valve (339) and the spring (340).
Installation Procedure
http://localhost:9001/si/showDoc.do?docSyskey=803999&pubCellSyskey=71418&pubObj... 12/6/2010
Document ID: 803999 Page 2 of 2
1. Install the spring (340), the TCC regulated apply valve (339), the TCC solenoid (335) with
two O-rings (337 and 338) and screen, and the TCC solenoid retainer clip (304).
2. Install the transmission side cover. Refer to Control Valve Body Cover Replacement
Resetting the TAP values using a scan tool will erase all learned values in all cells. As a result,
The ECM, PCM or TCM will need to relearn TAP values. Transmission performance may be
affected as new TAP values are learned.
http://localhost:9001/si/showDoc.do?docSyskey=803999&pubCellSyskey=71418&pubObj... 12/6/2010
Document ID: 803998 Page 1 of 2
2009 Saturn VUE - FWD | VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual | Transmission |
Automatic Transmission - 4T45-E | Repair Instructions - On Vehicle | Document ID: 803998
1. Remove the transmission side cover. Refer to Control Valve Body Cover Replacement .
2. Remove the 1-2 shift solenoid retainer clip (304), the 1-2 shift solenoid (305) with O-ring
(303), the 1-2 shift valve (302), and the 1-2 shift valve spring (301).
Installation Procedure
http://localhost:9001/si/showDoc.do?docSyskey=803998&pubCellSyskey=71419&pubObj... 12/6/2010
Document ID: 803998 Page 2 of 2
1. Install the 1-2 shift valve spring (301), the 1-2 shift valve (302), the 1-2 shift solenoid (305)
with O-ring (303) and the 1-2 shift solenoid retainer clip (304).
2. Install the transmission side cover. Refer to Control Valve Body Cover Replacement .
Resetting the TAP values using a scan tool will erase all learned values in all cells. As a result,
The ECM, PCM or TCM will need to relearn TAP values. Transmission performance may be
affected as new TAP values are learned.
http://localhost:9001/si/showDoc.do?docSyskey=803998&pubCellSyskey=71419&pubObj... 12/6/2010
Document ID: 803997 Page 1 of 2
2009 Saturn VUE - FWD | VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual | Transmission |
Automatic Transmission - 4T45-E | Repair Instructions - On Vehicle | Document ID: 803997
1. Remove the transmission side cover. Refer to Control Valve Body Cover Replacement .
2. Remove the 2-3 shift solenoid retainer clip (304), the 2-3 shift solenoid (305) with O-ring
(303), the 2-3 shift valve (307), and the 2-3 shift valve spring (306).
Installation Procedure
http://localhost:9001/si/showDoc.do?docSyskey=803997&pubCellSyskey=71420&pubObj... 12/6/2010
Document ID: 803997 Page 2 of 2
1. Install the 2-3 shift valve spring (306), the 2-3 shift valve (307), the 2-3 shift solenoid (305)
with O-ring (303) and the 2-3 shift solenoid retainer clip (304).
2. Install the transmission side cover. Refer to Control Valve Body Cover Replacement .
Resetting the TAP values using a scan tool will erase all learned values in all cells. As a result,
The ECM, PCM or TCM will need to relearn TAP values. Transmission performance may be
affected as new TAP values are learned.
http://localhost:9001/si/showDoc.do?docSyskey=803997&pubCellSyskey=71420&pubObj... 12/6/2010
Document ID: 803993 Page 1 of 2
2009 Saturn VUE - FWD | VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual | Transmission |
Automatic Transmission - 4T45-E | Repair Instructions - On Vehicle | Document ID: 803993
1. Remove the transmission side cover. Refer to Control Valve Body Cover Replacement
2. Remove the Pressure Control Solenoid (PCS) retainer clip (304), the PCS with two O-rings
and screen (312, 309, 310), the torque signal regulator valve (309), and the torque signal
regulator spring (308).
Installation Procedure
http://localhost:9001/si/showDoc.do?docSyskey=803993&pubCellSyskey=71421&pubObj... 12/6/2010
Document ID: 803993 Page 2 of 2
1. Install the torque signal regulator spring (308), the torque signal regulator valve (309), the
Pressure Control Solenoid (PCS) with two O-rings and screen (312, 309, 310) and the PCS
retainer clip (304).
2. Install the transmission side cover. Refer to Control Valve Body Cover Replacement .
Resetting the TAP values using a scan tool will erase all learned values in all cells. As a result,
The ECM, PCM or TCM will need to relearn TAP values. Transmission performance may be
affected as new TAP values are learned.
http://localhost:9001/si/showDoc.do?docSyskey=803993&pubCellSyskey=71421&pubObj... 12/6/2010
Document ID: 2159533 Page 1 of 2
2009 Saturn VUE - FWD | VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual | Transmission |
Automatic Transmission - 4T45-E | Repair Instructions - On Vehicle | Document ID: 2159533
1. Remove the transmission side cover. Refer to Control Valve Body Cover Replacement.
2. Remove the six bolts from the transmission fluid pressure (TFP) switch assembly.
3. Remove the TFP switch assembly from the control valve body assembly (18). The 4 pressure
switch O-rings are reusable and should remain with the TFP switch assembly.
Installation Procedure
http://localhost:9001/si/showDoc.do?docSyskey=2159533&pubCellSyskey=71422&pubO... 12/6/2010
Document ID: 2159533 Page 2 of 2
1. Install the TFP switch assembly to the control valve body assembly (18). The 4 pressure
switch O-rings are reusable and should remain with the TFP switch assembly.
2. Install the six bolts to the TFP switch assembly and tighten to 12 N·m (9 lb ft).
3. Install the transmission side cover. Refer to Control Valve Body Cover Replacement.
Resetting the TAP values using a scan tool will erase all learned values in all cells. As a result,
The ECM, PCM or TCM will need to relearn TAP values. Transmission performance may be
affected as new TAP values are learned.
http://localhost:9001/si/showDoc.do?docSyskey=2159533&pubCellSyskey=71422&pubO... 12/6/2010
Document ID: 2137646 Page 1 of 8
2009 Saturn VUE - FWD | VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual | Transmission |
Automatic Transmission - 4T45-E | Repair Instructions - On Vehicle | Document ID: 2137646
Removal Procedure
1. Remove the transaxle case side cover. Refer to Control Valve Body Cover Replacement.
2. Remove the oil pump bolts and the oil pump assembly.
3. Remove the oil pump shaft.
http://localhost:9001/si/showDoc.do?docSyskey=2137646&pubCellSyskey=71423&pubO... 12/6/2010
Document ID: 2137646 Page 2 of 8
5. Remove the TFP switch assembly bolts and remove the switch assembly from the control
valve body. The 7 TFP switch O-rings are reusable if not damaged and should remain with
the pressure switch assembly.
6. Remove the remaining control valve body bolts (9, 12, 16) and remove the control valve
body assembly (18).
http://localhost:9001/si/showDoc.do?docSyskey=2137646&pubCellSyskey=71423&pubO... 12/6/2010
Document ID: 2137646 Page 3 of 8
7. Remove the spacer plate support bolts (20) and remove the spacer plate support (21).
Note: Checkballs may fall out of the channel plate assembly. Retain the checkballs with
petroleum jelly.
8. Remove the spacer plate (90) with the spacer plate filter attached.
9. Remove and discard the spacer plate assembly (90).
Disassembly/Assembly Procedure
For step by step instructions on how to disassemble/assemble the control valve body, refer to
Control Valve Body Disassemble and Control Valve Body Assemble.
Installation Procedure
http://localhost:9001/si/showDoc.do?docSyskey=2137646&pubCellSyskey=71423&pubO... 12/6/2010
Document ID: 2137646 Page 4 of 8
1. Make sure the checkballs (1-7) are in the proper locations on the channel plate. Retain the
checkballs with petroleum jelly.
2. Install a new spacer plate assembly (90) onto the channel plate.
3. Hand start the spacer plate support bolts (20) and install the spacer plate support (21).
http://localhost:9001/si/showDoc.do?docSyskey=2137646&pubCellSyskey=71423&pubO... 12/6/2010
Document ID: 2137646 Page 5 of 8
4. Install a new control valve body to the spacer plate assembly (90).
5. Install the control valve body assembly onto the gasket. Hand start the control valve body
assembly bolts (9, 12, 16) to hold the valve body in place.
6. Inspect the TFP switch assembly (2) in order to verify the condition and the correct location
of the pressure switch O-rings. If necessary, replace the TFP switch assembly O-rings.
7. Install the TFP switch assembly onto the control valve body assembly.
http://localhost:9001/si/showDoc.do?docSyskey=2137646&pubCellSyskey=71423&pubO... 12/6/2010
Document ID: 2137646 Page 6 of 8
http://localhost:9001/si/showDoc.do?docSyskey=2137646&pubCellSyskey=71423&pubO... 12/6/2010
Document ID: 2137646 Page 7 of 8
Note: The 1-2 shift solenoid wires are red and green. The 2-3 shift solenoid wires are red
and yellow.
http://localhost:9001/si/showDoc.do?docSyskey=2137646&pubCellSyskey=71423&pubO... 12/6/2010
Document ID: 2137646 Page 8 of 8
11. Install the oil pump shaft into the control valve body assembly.
Note: If necessary, rotate the oil pump shaft while installing the oil pump assembly in order
to engage the shaft splines to the splines on the oil pump rotor.
12. Install the oil pump assembly onto the oil pump shaft and the control valve body..
Hand start and install the oil pump assembly bolts and tighten to 12 N·m (9 lb ft).
13. Install the transaxle case side cover. Refer to Control Valve Body Cover Replacement.
14. Start the engine, warm up the transaxle, and check for leaks.
15. Inspect for proper fluid level. Refer to Transmission Fluid Check.
Resetting the TAP values using a scan tool will erase all learned values in all cells. As a result,
the ECM, PCM or TCM will need to relearn TAP values. Transmission performance may be
affected as new TAP values are learned.
http://localhost:9001/si/showDoc.do?docSyskey=2137646&pubCellSyskey=71423&pubO... 12/6/2010
Document ID: 1466582 Page 1 of 6
2009 Saturn VUE - FWD | VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual | Transmission |
Automatic Transmission - 4T45-E | Repair Instructions - On Vehicle | Document ID: 1466582
Removal Procedure
Important:
• The stub axle shaft sleeve and seal must be replaced together. DO NOT replace the
sleeve or seal separately.
• Do not damage the seal bore or the sleeve assembly. Fluid leaks may result.
1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .
2. Remove the right drive axle assembly. Refer to Front Wheel Drive Shaft Replacement .
3. Remove the snap ring from the stub axle shaft. Discard the snap ring. Do not reuse.
http://localhost:9001/si/showDoc.do?docSyskey=1466582&pubCellSyskey=75570&pubO... 12/6/2010
Document ID: 1466582 Page 2 of 6
4. Install the J 38868 and J 6125-1B into the stub shaft snap ring groove.
5. Pull lightly on the shaft while rotating the shaft until the stub shaft snap ring at the
differential seats in the taper on the differential side gear.
6. Remove the stub shaft from the transmission.
http://localhost:9001/si/showDoc.do?docSyskey=1466582&pubCellSyskey=75570&pubO... 12/6/2010
Document ID: 1466582 Page 3 of 6
9. Remove the right hand axle seal from the transmission. Use the J 23129 and the J 6125-1B .
Installation Procedure
http://localhost:9001/si/showDoc.do?docSyskey=1466582&pubCellSyskey=75570&pubO... 12/6/2010
Document ID: 1466582 Page 4 of 6
Important: J 41228 must be used in order to install the sleeve to the correct depth.
http://localhost:9001/si/showDoc.do?docSyskey=1466582&pubCellSyskey=75570&pubO... 12/6/2010
Document ID: 1466582 Page 5 of 6
Important: J 41102-1A must be used in order to install the axle seal to the correct depth.
9. Install a NEW seal (1). Use the J 41102-1A (3) with J 8092 (2) . Lubricate the seal lip with
transmission fluid.
Important: Carefully guide the axle shaft past the lip seal. Do not allow the shaft splines to
contact any portion of the seal lip surface, otherwise damage to the seal will occur.
10. Install the stub shaft into the transmission. Use a mallet to fully seat the shaft.
11. Install the right drive axle assembly. Refer to Front Wheel Drive Shaft Replacement .
12. Lower the vehicle.
13. Inspect the oil level. Refer to Transmission Fluid Check .
http://localhost:9001/si/showDoc.do?docSyskey=1466582&pubCellSyskey=75570&pubO... 12/6/2010
Document ID: 1466582 Page 6 of 6
http://localhost:9001/si/showDoc.do?docSyskey=1466582&pubCellSyskey=75570&pubO... 12/6/2010
Document ID: 1466585 Page 1 of 4
2009 Saturn VUE - FWD | VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual | Transmission |
Automatic Transmission - 4T45-E | Repair Instructions - On Vehicle | Document ID: 1466585
Removal Procedure
1. Raise the vehicle. Support the vehicle. Refer to Lifting and Jacking the Vehicle .
2. Remove the left drive axle assembly. Refer to Front Wheel Drive Shaft Replacement .
3. Remove the snap ring from axle. Discard the snap ring. Do not reuse.
http://localhost:9001/si/showDoc.do?docSyskey=1466585&pubCellSyskey=75571&pubO... 12/6/2010
Document ID: 1466585 Page 2 of 4
5. Use the J 41227 to remove the sleeve from the output axle.
Installation Procedure
Important:
• The stub axle shaft sleeve and seal must be replaced together. DO NOT replace the sleeve or
seal separately.
• Do not damage the seal bore or the sleeve assembly. Fluid leaks may result.
http://localhost:9001/si/showDoc.do?docSyskey=1466585&pubCellSyskey=75571&pubO... 12/6/2010
Document ID: 1466585 Page 3 of 4
Important: J 41102-1A must be used in order to install the axle seal to the correct depth.
1. Install a new output axle seal (3). Use J 41102-1A (2) with J 8092 (1). Lubricate the seal lip
with transmission fluid.
2. Apply grease to the output shaft splines.
Important: J 41228 must be used in order to install the sleeve to the correct depth.
http://localhost:9001/si/showDoc.do?docSyskey=1466585&pubCellSyskey=75571&pubO... 12/6/2010
Document ID: 1466585 Page 4 of 4
6. Install the bearing and nut onto the threaded collet shaft.
7. Hold the collet shaft while tightening the nut in order to press the sleeve onto the output
shaft.
8. Remove the J 41228 .
http://localhost:9001/si/showDoc.do?docSyskey=1466585&pubCellSyskey=75571&pubO... 12/6/2010
Document ID: 2168557 Page 1 of 1
2009 Saturn VUE - FWD | VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual | Transmission |
Automatic Transmission - 4T45-E | Repair Instructions - On Vehicle | Document ID: 2168557
Note: Before replacing any transmission mount due to a suspected fluid loss, verify that the
source of the fluid is the mount.
http://localhost:9001/si/showDoc.do?docSyskey=2168557&pubCellSyskey=121125&pub... 12/6/2010
Document ID: 2168562 Page 1 of 2
2009 Saturn VUE - FWD | VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual | Transmission |
Automatic Transmission - 4T45-E | Repair Instructions - On Vehicle | Document ID: 2168562
Preliminary Procedures
1. Raise the vehicle. Refer to Lifting and Jacking the Vehicle.
2. Remove the front bumper fascia air deflector. Refer to Front Bumper Fascia Air
Deflector Replacement.
3. Support the transmission with a transmission jack stand.
Front Transmission Mount Thru Bolt
Tighten
110 N·m (81 lb ft)
Front Transmission Mount Bolt
2
Tighten
90 N·m (66 lb ft)
http://localhost:9001/si/showDoc.do?docSyskey=2168562&pubCellSyskey=3723&pubObj... 12/6/2010
Document ID: 2168562 Page 2 of 2
http://localhost:9001/si/showDoc.do?docSyskey=2168562&pubCellSyskey=3723&pubObj... 12/6/2010
Document ID: 2168565 Page 1 of 2
2009 Saturn VUE - FWD | VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual | Transmission |
Automatic Transmission - 4T45-E | Repair Instructions - On Vehicle | Document ID: 2168565
Preliminary Procedures
1. Raise the vehicle. Refer to Lifting and Jacking the Vehicle.
2. Support the transmission with a transmission jack stand.
3. Disconnect the steering shaft coupler from the steering gear. Refer to Steering Gear
Replacement.
4. Remove the steering gear to frame bolts. Refer to Steering Gear Replacement.
5. Position the steering gear up out of the way to gain clearance for removal of the rear
transmission mount.
Rear Transmission Mount Thru Bolt
Tighten
110 N·m (81 lb ft)
Rear Transmission Mount Bolt (Qty: 3)
2
Tighten
50 N·m (37 lb ft)
© 2010 General Motors Corporation. All rights reserved.
http://localhost:9001/si/showDoc.do?docSyskey=2168565&pubCellSyskey=3724&pubObj... 12/6/2010
Document ID: 2168565 Page 2 of 2
http://localhost:9001/si/showDoc.do?docSyskey=2168565&pubCellSyskey=3724&pubObj... 12/6/2010
Document ID: 2168566 Page 1 of 5
2009 Saturn VUE - FWD | VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual | Transmission |
Automatic Transmission - 4T45-E | Repair Instructions - On Vehicle | Document ID: 2168566
http://localhost:9001/si/showDoc.do?docSyskey=2168566&pubCellSyskey=117658&pub... 12/6/2010
Document ID: 2168566 Page 2 of 5
http://localhost:9001/si/showDoc.do?docSyskey=2168566&pubCellSyskey=117658&pub... 12/6/2010
Document ID: 2168566 Page 3 of 5
Installation Procedure
2. Install the transmission mount to frame rail bolts and tighten to 27 N·m (20 lb ft).
http://localhost:9001/si/showDoc.do?docSyskey=2168566&pubCellSyskey=117658&pub... 12/6/2010
Document ID: 2168566 Page 4 of 5
3. Install the transmission mount spacer and bolts and tighten the bolts to 50 N·m (37 lb ft).
4. Using the engine support, raise the transmission until the transmission mount spacer
contacts the left transmission mount.
5. Install the transmission mount to transmission mount spacer bolts (1) and tighten to 50 N·m
(37 lb ft).
6. Raise the vehicle.
http://localhost:9001/si/showDoc.do?docSyskey=2168566&pubCellSyskey=117658&pub... 12/6/2010
Document ID: 2168566 Page 5 of 5
7. Install the rear transmission mount thru bolt (1) and tighten to 100 N·m (74 lb ft).
8. Install the front transmission mount thru bolt and tighten to 110 N·m (81 lb ft).
9. Lower the vehicle.
10. Remove the engine support fixture. Refer to Engine Support Fixture.
11. Install the battery box if equipped with 2.4L (LE5). Refer to Battery Box Replacement.
12. Install the battery tray support bracket if equipped with 2.4L (LAT). Refer to Battery Tray
Support Bracket Replacement.
http://localhost:9001/si/showDoc.do?docSyskey=2168566&pubCellSyskey=117658&pub... 12/6/2010
Document ID: 2168569 Page 1 of 1
2009 Saturn VUE - FWD | VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual | Transmission |
Automatic Transmission - 4T45-E | Repair Instructions - On Vehicle | Document ID: 2168569
Preliminary Procedures
Remove the rear transmission mount. Refer to Transmission Rear Mount Replacement.
Rear Transmission Mount Bracket Bolt (Qty: 3)
Tighten
50 N·m (37 lb ft)
2 Rear Transmission Mount Bracket
http://localhost:9001/si/showDoc.do?docSyskey=2168569&pubCellSyskey=122875&pub... 12/6/2010
Document ID: 2168572 Page 1 of 1
2009 Saturn VUE - FWD | VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual | Transmission |
Automatic Transmission - 4T45-E | Repair Instructions - On Vehicle | Document ID: 2168572
Preliminary Procedures
1. Raise the vehicle. Refer to Lifting and Jacking the Vehicle.
2. Remove the right engine splash shield. Refer to Engine Splash Shield Replacement.
Transmission Brace Bolt (Qty: 2)
Tighten
53 N·m (39 lb ft)
Transmission Brace Bolt (Qty: 2)
2
Tighten
53 N·m (39 lb ft)
3 Transmission Brace
http://localhost:9001/si/showDoc.do?docSyskey=2168572&pubCellSyskey=3686&pubObj... 12/6/2010
Document ID: 2125622 Page 1 of 9
2009 Saturn VUE - FWD | VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual | Transmission |
Automatic Transmission - 4T45-E | Repair Instructions - On Vehicle | Document ID: 2125622
Transmission Replacement
Special Tools
Removal Procedure
1. Remove the battery tray support bracket. Refer to Battery Tray Support Bracket
Replacement.
2. Remove the generator control module, if equipped with 2.4L (LAT). Refer to Generator
Control Module Replacement.
3. Remove the auxiliary fluid pump and pipes, if equipped with 2.4L (LAT). Refer to one of the
following:
• Auxiliary Fluid Pump Replacement
• Auxiliary Fluid Pump Inlet Pipe Replacement
• Auxiliary Fluid Pump Outlet Pipe Replacement
4. Remove the air cleaner outlet duct. Refer to Air Cleaner Outlet Duct Replacement.
5. Disconnect the transmission electrical wiring harness connector from the park neutral
position (PNP) switch.
6. Disconnect the transmission main wiring harness from the transmission.
7. Remove the wiring harness from the retainer on the transmission.
8. Remove the battery ground cable from the transmission, if equipped.
9. Disconnect the transmission shift control cable terminal (2) from the transmission manual
shift lever pin (1).
10. Press the locking tabs (3) inward in order to release the transmission shift control cable from
the cable bracket (4).
© 2010 General Motors Corporation. All rights reserved.
http://localhost:9001/si/showDoc.do?docSyskey=2125622&pubCellSyskey=3452&pubObj... 12/6/2010
Document ID: 2125622 Page 2 of 9
http://localhost:9001/si/showDoc.do?docSyskey=2125622&pubCellSyskey=3452&pubObj... 12/6/2010
Document ID: 2125622 Page 3 of 9
http://localhost:9001/si/showDoc.do?docSyskey=2125622&pubCellSyskey=3452&pubObj... 12/6/2010
Document ID: 2125622 Page 4 of 9
23. Disconnect the vehicle speed sensor (VSS) wiring harness connector and retainer from the
sensor.
24. Lower the vehicle.
25. Remove the left transmission mount and spacer. Refer to Transmission Mount Replacement -
Left Side.
26. Raise the vehicle. Refer to Lifting and Jacking the Vehicle.
27. Disconnect the wheel drive shafts from the transmission. Refer to Front Wheel Drive Shaft
Replacement.
28. Support the transmission with a suitable jack.
http://localhost:9001/si/showDoc.do?docSyskey=2125622&pubCellSyskey=3452&pubObj... 12/6/2010
Document ID: 2125622 Page 5 of 9
33. Flush the transmission cooler and the lines with J 35944-A .
Installation Procedure
1. If previously removed, install the PNP switch. Refer to Park/Neutral Position Switch
Replacement.
2. Position the transmission to the engine.
3. Install the lower transmission to engine bolts (1) and tighten to 75 N·m (55 lb ft).
4. Install the wheel drive shafts to the transmission. Refer to Front Wheel Drive Shaft
Replacement.
5. Lower the vehicle.
6. Install the left transmission mount and spacer. Refer to Transmission Mount Replacement -
Left Side.
7. Raise the vehicle. Refer to Lifting and Jacking the Vehicle.
8. Lubricate the transmission cooler pipes before inserting into the seals.
9. Connect the transmission cooler pipes to the transmission.
10. Install the transmission cooler pipes retainer nut and tighten to 7 N·m (62 lb in).
http://localhost:9001/si/showDoc.do?docSyskey=2125622&pubCellSyskey=3452&pubObj... 12/6/2010
Document ID: 2125622 Page 6 of 9
11. Connect the wiring harness connector and retainer to the VSS.
12. Use the J 43653 to prevent the crankshaft from rotating.
13. Install the torque converter to flywheel bolts and tighten to 60 N·m (44 lb ft).
14. Install the starter. Refer to Starter Motor Replacement.
http://localhost:9001/si/showDoc.do?docSyskey=2125622&pubCellSyskey=3452&pubObj... 12/6/2010
Document ID: 2125622 Page 7 of 9
19. Install the upper transmission to engine bolts (1) and tighten to 75 N·m (55 lb ft).
http://localhost:9001/si/showDoc.do?docSyskey=2125622&pubCellSyskey=3452&pubObj... 12/6/2010
Document ID: 2125622 Page 8 of 9
22. Install the transmission shift control cable (3) to the cable bracket (4).
23. Connect the transmission shift control cable terminal (2) to the transmission manual shift
lever pin (1).
24. Connect the transmission main electrical wiring harness connector to the transmission.
25. Connect the transmission electrical wiring harness connector to the park neutral position
(PNP) switch.
26. Attach the wiring harness to the retainer on the transmission.
27. Install the battery ground cable to the transmission, if equipped.
28. Install the air cleaner outlet duct. Refer to Air Cleaner Outlet Duct Replacement.
29. Install the auxiliary fluid pump and pipes, if equipped with 2.4L (LAT). Refer to one of the
following:
http://localhost:9001/si/showDoc.do?docSyskey=2125622&pubCellSyskey=3452&pubObj... 12/6/2010
Document ID: 2125622 Page 9 of 9
Resetting the TAP values using a scan tool will erase all learned values in all cells. As a result,
the ECM, PCM or TCM will need to relearn TAP values. Transmission performance may be
affected as new TAP values are learned.
http://localhost:9001/si/showDoc.do?docSyskey=2125622&pubCellSyskey=3452&pubObj... 12/6/2010