Operator's Manual
Operator's Manual
DD210
DECLARATION OF CONFORMITY
2. INTRODUCTION TO MACHINE . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4. TRAMMING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
4.2. Tramming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
5. DRILLING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
6. TRANSPORTATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
7. TECHNICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Danger. Always have a fire extinguisher at hand and learn how to use
it.Have the extinguisher inspected and serviced regularly according to
the local regulations and to the extinguisher maintenance manual.
Danger. Always check the efficiency of the safety devices before using
the machines: emergency stop push button, emergency brakes,
backward tramming light and buzzer, tramming and working light,
horn, etc...
Danger. All hoods must be correctly mounted on the machine and the
doors correctly closed and locked, this all the time in order to prevent
accident with moving components such a engine belt, cable reel chain,
etc...
Danger. Before moving the booms make sure that the jacks and the
stabilizers are firmly in contact to the ground.
Danger. Service operations should be carried out only when the rig is
stopped. Replace or repair faulty tools and equipment.
Make sure that there are no unauthorized persons in the working area
when you carry out service and repair work.
The drilling equipment must always be kept clean of oil and dirt.
Danger. Danger of high pressure air streams. The air streams can
cause serious personal injuries.
Release the pressure before opening filling caps or pneumatic
connections.
Danger. The lubricator, the compressor air/oil receiver and any air
receiver are pressure vessels and they are not allowed to be repaired
without proper authorization.
Check regularly the certification validity of those componnents.
At the end of validity period, you must make recertify the component
by a registered organization or replace it by a new one.
Danger. If you have to weld the rig, disconnect the alternator cables or
open the main switch before starting to weld. Consider also the fire
and explosion risk caused by welding. Make sure that the rig and its
WARNING
surroundings are clean and fire-safe.
WARNING Before operating maintenance always plan your work in order to use
adequate and in good shape receptacles.
Do not use the diesel engine if it is not needed because of exhaust gas,
think about the people and the environment.
3 8
5 DATE DE FABRICATION 2
1 4
6
NOM TYPE N°SERIE
• 1- Machine name and type
PUISSANCE INSTALLEE : DIESEL Kw ELECTRIQUE Kw
70961046
7 SANDVIK MINING AND CONSTRUCTION LYON SAS AV.DE LATTRE DE TASSIGNY
BP 46 69881 MEYZIEU CEDEX FRANCE • 3- Diesel engine power
AV / FRONT AR / REAR
• 4- Electric input power
PRESSION DE GONFLAGE BAR BAR
9 10
• 6- Electric frequency
11 12 • 7- Total weight of the machine
2
1 • 8- Manufacturing date
• 9- Front tyre inflation pressure
SANDVIK MINING AND CONSTRUCTION LYON
AV.DE LATTRE DE (bar)
TYPE 13
N° SERIE N° D’ORDRE • 10- Rear tyre inflation
8 DATE
pressure (bar)
• 11- Front tyre inflation
pressure (psi)
• 12- Rear tyre inflation
pressure (psi)
• 13- Order number
Canopy
telescoping leg
Canopy
These two positions must clearly be marked on
telescoping leg
the canopy telescoping leg in order to inform the
operator of the machine.
PAINT LINE
Danger. You must paint these two marks on the canopy leg, using the
pen supplied in the package. Apply a paint line over a width
approximately 15mm (1/2 inch) wide.
WARNING
TRAMMING POSITION
PARKING POSITION
• Boom and drill feed must be in line with the machine axis.
• Lower the drill boom and drill feed as far as possible.
• Machine must be on stabilizers in parking position.
5m
WARNING WARNING
DANGEROUS AREAS:
• 5m toward the front end of the drill feed and
5m backward the rear end of the carrier.
• Area between the machine and the side wall
of the drift.
WARNING
5m
Ensure that the machine is in perfect
operating condition.
NO PERSONNEL ALLOWED
WARNING
WARNING
WARNING
NO PERSONNEL ALLOWED
• Keep the machine clean at all times, especially from fuel, grease, oil rags
and paper.
WARNING • Wash the machine regularly.
• Check fire extinguishers and/or fire prevention equipment daily to ensure
that they are in perfect working order.
• Keep electric components and wiring in good condition.
• The filling of tanks must be carried out in a well-ventilated area.
• The control and recharging of batteries must be carried out in a well-
ventilated area.
WARNING
PUSH BUTTON
PIN
The fire extinguisher actuators are located in A at the tramming compartment and in B
at the rear of the machine, as shown on the drawing.
When any emergency stop push button is depressed, the Diesel engine and the power
pack stop at once.
EMERGENCY STOP
EMERGENCY STOP
PUSH BUTTON
PUSH BUTTON
(O) EMERGENCY/
PARK BRAKE
PUSH BUTTON
(O) EMERGENCY/
PARK BRAKE
PUSH BUTTON
By-passing
switch for
machine’s towing
The cable must never be live before the machine is ready to drill and
the cable itself has been placed in its support and support hooks.
NEVER HANDLE A LIVE CABLE.
2. INTRODUCTION TO MACHINE
This manual provides instructions for the use and safe operation of a DD210 face drilling
machine
The information contained in this manual must be studied and thoroughly assimilated
before attempting to operate this machine.
One or other of the following symbols have been used throughout the manual in order to
highlight a particular aspect of the machine which the operator must be aware of them at all
times.
NOTE: This symbol is used to indicate the specific functioning of a particular component.
Caution. This symbol is used to indicate that failure to comply with
the instructions in this manual could cause damage to the machine.
Danger. This symbol is used to warn the operator that improper use of
the machine could cause injury to himself and to those in the
immediate area of the machine.
The information contained in these paragraphs must be adhered to at
WARNING all times.
Never attempt to operate a machine unless all required preventive maintenance has
been performed. All damage and faulty operation must be reported immediately for
corrective action by authorized maintenance personnel.
NOTE: Any and all operators must be properly trained before attempting to operate
this machine unassisted.
FRONT REAR
3
4
ROCK DRILL
5 2
1. Low pressure accumulator
X2
4 2. Hight pressure
accumulator
3. Rotation motor
4. Flushing housing
5. Percussion assy
1
3
HYDRASTAR 200 Rock Drill
H200 2 1
1. Pressure accumulator
4 2. Rotation motor housing
3. Percussion housing
4. Flushing head
1
HLX5
4
3
1. Pressure accumulator
2. Rotation motor
3. Flushing housing
4. Gear housing
1
2
3 4 2
HL510
1
CC 2500 Series Feed
FEED
2
3
1. Hose reel
4 2. Rock drill carriage
3. Feed cylinder, wire ropes
1
4. Centralizers
CC2500
2
3
TF500
Divergence
B14F
Feed Extension
Feed Swing
Feed Roll-over
Boom Swing
Feed Tilt
Boom Lift
Ensure horizontal //
Ensure vertical //
DRILLING COMPARTMENT
KVL10 rock drill oiler air pressure gauge
Rotation Air mist ball valve
(optional) Air mist flowmeter
pressure gauge (optional)
Boom control levers Feed thrust lever Electric control box Rotation lever
1
3
7
1
2
1. Hose reel
3
2. Gun
4 3. Grease pump
4. Air pressure gauge
4 5. Grease pump oiler
REAR SECTION
2
3
1. Operator seat
2. Safety telescopic canopy
3. Cable reel
4. Electric control panel
5. Inside or outside rear
4 5 stabilizers (optional)
7 12 6. Tramming compartment
6 8
7. Oil tank
1
8. Diesel engine
9. Tuflo 1000 air compressor
10. Fuel tank
11. Electric power pack
12. Water pump
11
9 REAR SECTION
10
5 2
1 4
3
6
13
CHECK
CHECK FOR :
• Possible transportation damage.
• Tyre pressure and condition.
• All oil and fuel levels.
WARNING
PINS
1
TYPE A
2
• Lock plate 2 must be in contact to the
support 1.
• Fastening screws in place and
tighten.
TYPE B
• Fastening bolt 1 in place and tighten.
TYPE C
• Fastening bolt 1 in place and tighten.
1
WHEELS
FUEL LEVEL
WARNING
AIR FILTER
Caution ligth
Filling cap
WATER CIRCUIT
Water filter
The water pump must be drained
drain ball valve before each start and after each
maintenance work on the water circuit.
Water pump
drain ball valve
2 variant positions
• The bolster pin must be greased using the two deported greasing points.
• The carrier central articulation, stabilizers & the cable guide must be also
greased.
HOURMETERS
Horn
Alternator
Blower belt
caution light
failure
Glow plug
Contact key
indicator
Engine temperature
caution light
14 12
Danger. Never swing the boom unless all four stabilizing jacks
are in solid contact with the ground.
When tramming, only the drill feed swing is authorized. refer to
chapter «drilling» for boom operation.
Always adhere to the grade and side slope limitations.
WARNING
4. TRAMMING
4.1. Starting the engine
Danger. Always make sure before starting the engine that there is no
unauthorized persons in the danger areas around the machine and that
no controls are in operating position.
Danger. Sound the horn to warn any person of your intention to start
and move the machine.Make sure that all covers and protective hoods
and doors are installed and properly closed.
5 1
4.2. Tramming
Using the accelerator lever, bring the engine to FULL RPM. The pressure indicated on
the 0-25 bar pressure gauge, located at the operator compartment, must read no less
than 15 bar.
EMERGENCY/ PARK BRAKES TEST
• 1. Steering lever.
• 2. Tramming lever.
• 3. Emergency/Park brake push button.
TRAMMING LEVER
Pull = BACKWARD Push = FORWARD
Neutral
• Drive slowly around corners, sound the
Slow Slow horn and warn people in areas you cannot
Fast Fast see.
• Observe speed limit regulation.
Accelerator
5. DRILLING
5.1. Basic rules of safety
5.1.1 Safety precautions
USER’S SAFETY, HIGH AVAILABILITY AND LOW OPERATING COST are
dependent on the correct use of this machine.
MACHINE, UNDERSTAND ITS CAPABILITIES, FOLLOW OPERATING
PROCEDURES AND BE CONVERSANT WITH THE SAFETY RELATED
PROCEDURES CONTAINED IN THIS MANUAL.
WARNING
General inspection:
All the articulation and cylinder pins must be greased and correctly positioned.
The hoses must be kept under the protection of the spiral sheath which offers two
advantages:
- preventing the hoses from becoming coated with oil and grease
- preventing wear by direct contact with the ground.
Position of the front triggers, do not over lift the chassis for maximum stability (see
figure).
Danger. When placing the stabilizers, pay attention that nobody is
close to them.
Maximum rear
stability
ON
RESET
OFF
NOTE: To be able to use the main electric switch you should turn first the battery
master switch ON. Rotate then the main switch in position ON.
After using of the emergency stop button the main breaker will be placed
automatically in TRIP position.
NOTE: do not use the emergency stop button in normal process to stop any of the
power pack, use dedicated stop button.
Power pack ON
Power pack
Phase setting
ON
light
Main electric
supply “ON”
Diesel / Electric
selector switch
THE MOTOR(S) CAN NOW BE STARTED. While the motor is running the «motor
running» light is activated.
OFF - ON
Air flushing
(optional)
B14F
Feed Extension
Feed Swing
Feed Roll-over
Boom Swing
Feed Tilt
Boom Lift
Ensure horizontal //
Ensure vertical //
BOOM CONTROLS
PUSH
PUSH
LEFT
RIGHT
1 PULL
2 PULL
3 4 5
LEVER 5 - DIVERGENCE
• PUSH : Up feed divergence.
• PULL : Down feed divergence.
5.5. Drilling
5.5.1 Before drilling
INITIAL CONTROLS:
• Be sure that the position and the direction of the hole is correct.
• Be sure that the drill feed is firmly placed against the face and maintained in that
position throughout the drilling operation.
• Open the water flushing valve.
The pump will start automatically if the inlet water pressure is greater than 2 bar (51
psi).
NOTE: If the water pressure supplied by the mine is less than 2 bar or if the water filter is
clogged, the water pump stops automatically.
5.5.3 Drilling
• According to drilling conditions, proceed drilling with water flushing.
• Keep the rotation lever pushed DOWNWARD.
• Push the feed thrust lever DOWNWARD to the MAXIMUM feed position.
NOTE: The feed forward movement stops if there is lack of air pressure or water flow.
3 - ROD UNCOUPLING
Recommended procedure for uncoupling the bit or the shank adaptor.
• Anchor the drill feed and then open the water circuit.
• DO NOT USE THE ROTATION.
• Using the Feed Lever, advance the rockdrill.
• Move the Feed Lever to the’MAXIMUM feed’ position. This allows the full percussion
energy to be activated for a better breaking capability.
When you stop the drilling process at the end of the shift or for any other reason, carry
on following operations:
• Tilt the front end of the drill feed downward the stinger in contact to the ground.
• Stop the powerpack
• Close the water supply valve at the mine line
• As to prevent the alternator to be damaged, stop the diesel engine prior to turn the
battery master switch to the "OFF" position.
• Place the main electric breaker to the "OFF" position
• Shut OFF the power at the mine electric box.
• Wash the machine mainly the drill feed and the boom.
• Fill-up the shift report form.
• Report any defects that you have noticed.
6. TRANSPORTATION
6.1. Towing the machine
Danger. THE MAXIMUM TOWING SPEED MUST BE 1 KM/H. This to
prevent the tramming component to be damaged and operator affect at
drilling compartment.
THE USE OF CABLE OR CHAIN IS STRICTLY FORBIDEN. While
WARNING
towing, one operator should be at the tramming compartment ready to
apply the brake in a case of emergency or operate the steering valve to
allow the steering cylinder to move.
• If the machine gets the optional ABA brakes, you must turn to the right the ABA brakes
by-passing switch to by-pass the ABA brakes safety device, the switch turns on.
• Untight the both valves and turn them four revolutions counter-clockwise, to by-pass the
oil flow. The tramming motor can now turn without resistance.
Multi-function HP valves
Unscrew
Oil by pass
• Release the emergency/park brake valve by pulling, fully upward, the red knob.
• Close the ball valve of the unbraking hand-pump.
Danger. This ball valve must be always open in normal use of the
machine. If not, the park brake may not work, don’t forget to reopen the
ball valve after towing the machine.
WARNING
• Use the unbraking hand pump to pressurize the brake cylinders. The pressure build up
by the hand pump is sufficient to release the brakes.
NOTE: The brake valve is always functionning. To apply the brakes push downward the
red knob, as you do in normal conditions.
Danger. Never try to tow a machine which presents problems on
tramming components
WARNING
When driving the machine onto a transport platform, use ramps. this
should always be done on level ground.
Always use low speed and observe special caution when coming from the
ramps to the platform.
WARNING
LIFTING FRAME
Lifting hook
Lifting hook
Danger. Always respect the law and all the local safety regulations in
lifting work.
Keep in mind the total weight of the rig, given on the type plate.
Move the boom and the drill feed or turret to the tramming position .
Install the locking bar at the central articulation. Install 4 hooks and
chains or cables at the front and rear lifting points.
Danger. Do not stand under the machine during lifting process. Use
proper lifting devices such as hooks, cables or chains for a safe work.
Use a lifting frame to maintain all 4 four chains or cables vertical and
parallel to each other.
The lifting device used must be of the correct type and have sufficient lifting capacity.
The rig or parts of it must not be lifted with any devices that are not specifically
designed for lifting purposes.
You must always know the exact weight of the load, and never exceed the lifting
capacity specified by the manufacturer of the lifting device.
Lifting routes should be planned so that the load is not moved over persons or such
places where persons may be present.
Make sure that the lifting equipment is in proper condition Wire ropes and chains used
for lifting must be checked regularly. Damaged wire ropes must be marked clearly and
discarded at once.
Lift the load only a few centimetres at first to make sure that it is properly fastened and
in balance. Do not continue lifting until you are sure of proper fastening and balance.
The lifting wire ropes must be fastened according to the manufacturer’s instructions.
• The storing place temperature should be higher than the freezing point, and protected
against direct sunlight and rain.
• Wash the machine if it has been used or transported by sea using a high pressure
steam washing machine.
• Drain and blow air through the water circuit. Blow some anti-freeze (rust inhibitor)
through the circuit.
• Lubricate all greasing points.
• Bring the stabilizers in contact to the ground.
• The drill feed stinger should be in contact to the ground.
• The nitrogen rockdrill accumulator should be empty, PLACE A TAG TO REMIND THAT
THE ACCUMULATORS HAVE BEEN DISCHARGED.
• Coat the cylinder rod with grease.
• Drain the air reservoir(s).
• Replace all fluids: engine, hydraulic axle and gear oil.
• Spray a dust and corrosion inhibitor product on all electric devices.
• As to prevent the alternator to be damaged, stop the engine prior to turn the battery
master switch to the «OFF»position.
Technical Specification
6-110 S-G
2007-06-01
Sandvik DD210
GENERAL DIMENSIONS
900
1850
1950
1300
225
All dimensions in mm
HL 510 S ROCK DRILL (Technical specification 2-1150) B 14 F BOOM (Technical specification 4-100 S)
Technical Specification
6-110 S-G
2007-06-01
Sandvik DD210
TRAMMING DIMENSIONS
1950
1850
TF 500-8 9 090
TF 500-10 9 090
225
TF 500-12 9 530
Overall Length 2195 1910
4735
1200
TURNING RADIUS
2600
2750
3400
30° Outriggers A B
Standard 2390 2670
5100 Narrow 1930 2000 1340
A
All dimensions in mm
B
Technical Specification
6-110 S-G
2007-06-01
Sandvik DD210
COVERAGE AREA
Auto-parallel coverage
4400
3600
DD 210 on jacks.
All dimensions in mm.
4500
5500
OPTIONAL EQUIPMENT
DRILLING SYSTEM OTHER OPTIONAL EQUIPMENT
*) Hydrastar 200 Rock drill with CC 2500 feed. 1 x 6 kg Fire extinguisher (bottle only).
*) TTF 6/10 with HL 510 Rock drill. Fire suppression system ANSUL, 6 nozzles.
Rock drill auto-return. Reverse alarm.
Fast Rock drill return. *) EU, UL, CSA, AUS norms package.
*) FCC2 front clamping head on drill feed. Pressure cleaning system (10 bar) without reel.
SERH rod handler with controls (incl. FCC2). *) Electric oil filling pump.
Drill angle measuring instrument TMS D1. Centralized greasing.
Auto air flushing on rock drill return. Automatic lubrication system (Lincoln).
Air cleaner IP5 plus auxiliary connection for mine air network. Biodegradable oils.
*) Air mist flushing kit for auxiliary water/air connection. *) Ni-Cr plated cylinder rods.
*) Full Diesel drilling. Manuals other than French/English language.
ELECTRICAL SYSTEM *) replaces standard component
*) 1 000 V electric power supply.
Ground fault and overcurrent unit VYK 200. CAGING DIMENSIONS AND WEIGHT
Electrical cable (Technical specification 5-4100).
*) Allen Bradley electrics.
*) 2 x 35 W High Intensity Discharge (HID) working lights. Front Part Rear Part
2 x 70 W Halogen extra working lights.
Length (mm) 1 465 3 220
HIGH ALTITUDE OPTIONS
*) F4L 912W Diesel engine (1000 m < altitude < 2400 m). Width (mm) 1 200 1 200
Altitude compensator for F4L engine (altitude > 2400m)
Altitude compensator for F6L, full Diesel version. Height (mm) 1 440 1 480
CARRIER Weight (approximate) ... (kg) 2 400 4 000
2 x Rear jacks.
Nota: Caging and weight on primary dismantling, with wheels.
*) Front narrow outriggers for confined areas + 2 rear jacks.
*) Extendable front jacks.
Fume diluter.
Complete spare wheel.
Hand pump for manual brake release.
Technical Specification
2-310 S-C
2003-11-27
X2 Series Rock Drill
Technical Specification
2-310 S-C
2003-11-27
X2 Series Rock Drill
WORKING PARAMETERS
X2 F X2 L (<30 m) X2 L (>30 m)
Percussion mechanism
Operating pressure 160 - 210 bar 175 - 210 bar
Percussion power 14 - 19 kW 15 - 19 kW 16 - 21 kW
Percussion rate 52 - 59 Hz 57 - 59 Hz 53 - 55 Hz
Flow 90 l/min 90 l/min
Rotation mechanism
Motor Orbit type, 125 ccm Orbit type, 200 ccm
Flow 40 - 70 l/min 40 - 70 l/min
Rotation speed 220 - 350 rpm 135 - 240 rpm
Pressure 175 - 210 bar 140 - 175 bar
Torque 390 - 470 Nm 500 - 620 Nm
GENERAL DIMENSIONS
X2F X2L
1099 1099
969 969
115
87
190 190
Technical Specification
2-100 S-C
2007-05-10
Hydraulic rock drill Hydrastar 200
Technical Specification
2-100 S-C
2007-05-10
Hydraulic rock drill Hydrastar 200
GENERAL DIMENSIONS
908
765 765
243 243
70
152
115
297
182
TECHNICAL DATA
MAIN DIMENSION FLUSHING
Length 583 mm Max pressure (air/water) 15 bar
Profile height 70 mm
Width 297 mm ACCUMULATORS
Weight 95 kg Accumulator gas Nitrogen N2
High pressure (HP) 55 bar
ROTATION MECHANISM Filling valve Vg8 DIN 7756
Motor Orbit, OMS 125
Torque (at 210 bar) 420 Nm SHANK LUBRICATION
Rotation speed 0...300 rpm Air flow (at 6 bar) 250 l/min
Flow (at max speed) 40 l/min Pressure 2.5 bar
Oil consumption 100 g/h
OIL RECOMMENDATION
Oil operating temperature +40...+65° C
Oil recommendation See Sandvik drill rigs
lubricant recommenda-
tion for detailled
information
OPTIONS
Flushing head + 20 kg
Complete special tools kit, ID 783 400 65
Technical Specification
2-1852-B Hydraulic rock drill HLX 5
2007-06-28
A P PL IC A TI ON M A I N S P EC IF IC A T IO N S
HLX 5 hydraulic rock drill is designed for underground Hole diameter
face, bolt and long hole drilling. HLX 5 is standard rock Drifting 43...64 mm
drill f.ex on Sandvik hydraulic controlled mining and Cut hole drilling 76...127 mm
tunneling jumbos. Power class 20 kW
Percussion rate 67 Hz
Operating pressure
MAIN CHARAC TER ISTIC S Percussion 120-220 bar
HLX 5 is a compact, robust and universal hydraulic Rotation (max) 175 bar
percussive rock drill. It is known of its hydraulic effi- Rotation motor type OMS 80/125/160
ciency and high penetration rates. HLX 5 has excellent Drill steels R 39 or Hex 35 mm
serviceability through modular construction and visual drifter rods, MF-rods
wear indicators. Robustness is achieved by only few highly recommended
pressurized seems between the functional modules. Shanks Ø 45 / T 38
Technical Specification
2-1852-B Hydraulic rock drill HLX 5
2007-06-28
GENERAL DIMENSIONS
TECHNICAL DATA
MAIN DIMENSION FLUSHING
Length 955 mm Max pressure (air/water) 20 bar
Profile height 87 mm
Width 295 mm ACCUMULATORS
Weight 210 kg Accumulator gas Nitrogen N2
High pressure (HP) 50 bar
Low pressure (LP) 4 bar
ROTATION MECHANISM Filling valve Vg8 DIN 7756
Motor Orbit type (3 options)
Motor type 1 OMS 80 SHANK LUBRICATION
Torque (at 175 bar) 400 Nm
Air flow (at 6 bar) 250...350 l/min
Rotation speed 0…250 rpm
Pressure 4...7 bar
Flow (at max speed) 46 l/min
Oil consumption 180...250 g/h
Motor type 2 OMS 125
Torque (at 175 bar) 625 Nm OIL RECOMMENDATION
Rotation speed 0…250 rpm Oil operating temperature +40...+60 °C
Flow (at max speed) 72 l/min Oil recommendation See Sandvik drill rigs
lubricant recommenda-
Motor type 3 OMS 160 tion for detailed informa-
Torque (at 175 bar) 780 Nm tion
Rotation speed 0…200 rpm
Flow (at max speed) 74 l/min
OPTIONS
Special tools for HLX 5, ID 55006507
Technical Specification
2-1150-C
2007-05-10
Hydraulic rock drill HL 510 S/F
Technical Specification
2-1150-C
2007-05-10
Hydraulic rock drill HL 510 S/F
GENERAL DIMENSIONS
HL 510 F
1024
76
206
294
TECHNICAL DATA
MAIN DIMENSION FLUSHING
Length 1 024 mm Water pressure 10...20 bar
Profile height 76 mm
Width 294 mm ACCUMULATORS
Weight 130 kg Accumulator gas Nitrogen N2
High pressure (HP) 50 bar
ROTATION MECHANISM Low pressure (LP) 4 bar
Motor Orbit type (2 options) Filling valve Vg8 DIN 7756
Motor type 1 Orbit, OMS 80
SHANK LUBRICATION
Torque (at 175 bar) 400 Nm
Rotation speed 0...250 rpm Air flow (at 6 bar) 250...350 l/min
Flow (at max speed) 46 l/min Pressure 4...7 bar
Oil consumption 200...300 g/h
Motor type 2 Orbit, OMS 125
Torque (at 120 bar) 625 Nm OIL RECOMMENDATION
Rotation speed 0...250 rpm
Oil operating temperature +40...+60° C
Flow (at max speed) 72 l/min
Oil recommendation See Sandvik drill rigs
lubricant recommenda-
tion for detailled
information
OPTIONS
Complete special tools kit for HL 510, ID 152 257 68.
Field special tools kit for HL 300 S, ID 880 817 19.
'HVFULSWLRQ
GENERAL DIMENSIONS
TECHNICAL DATA
MAIN DIMENSION FLUSHING
Length 955 mm Max pressure (air/water) 20 bar
Profile height 87 mm
Width 295 mm ACCUMULATORS
Weight 210 kg Accumulator gas Nitrogen N2
High pressure (HP) 50 bar
Low pressure (LP) 4 bar
ROTATION MECHANISM Filling valve Vg8 DIN 7756
Motor Orbit type (3 options)
Motor type 1 OMS 80 SHANK LUBRICATION
Torque (at 175 bar) 400 Nm
Air flow (at 6 bar) 250...350 l/min
Rotation speed 0…250 rpm
Pressure 4...7 bar
Flow (at max speed) 46 l/min
Oil consumption 180...250 g/h
Motor type 2 OMS 125
Torque (at 175 bar) 625 Nm OIL RECOMMENDATION
Rotation speed 0…250 rpm Oil operating temperature +40...+60 °C
Flow (at max speed) 72 l/min Oil recommendation See Sandvik drill rigs
lubricant recommenda-
Motor type 3 OMS 160 tion for detailed informa-
Torque (at 175 bar) 780 Nm tion
Rotation speed 0…200 rpm
Flow (at max speed) 74 l/min
OPTIONS
Special tools for HLX 5, ID 55006507
Technical Specification
3-100 S-D
2005-05-02
CC 2500 Series Feed
APPLICATION DESCRIPTION
A series of rugged hydraulic steel feed intended for The CC 2500 hydraulic cylinder feeds are made from
drifting, bolt hole and cross-cuttings. heavy duty steel alloy profile. The high corrosion and
high torsional resistance steel beam is equipped with
Three models are available.
easily replaceable guiding rails fixed with large diameter
CC 2500 feeds are designed for Tamrock Axera jumbos studs and bolts.
with X 2 and Hydrastar 200 rock drills.
The carriage for rock drill have special wrap around
CC 2500 EV feeds, with central hose reel, are designed connecting shoes.
for restricted area when cross-cuttings are needed.
The drill rod centralizers are equipped with hardened
CC 2500 R are designed for use with RHR 50 or RHR steel wear-pieces and are designed for optimum
80 rotary drills. visibility and durability.
The hose support is a conical clamping system that
allows easy individual tensioning of each hose.
Technical Specification
3-100 S-D
2005-05-02
CC 2500 Series Feed
GENERAL DIMENSIONS
CC 2500
CC 2500 EV
CC 2500 R
Technical Specification
3-1400-D TF 500 HYDRAULIC CYLINDER FEED
2005-01-31
1
4
2
3 5 6
7
8
10
Technical Specification
3-1400-D TF 500 HYDRAULIC CYLINDER FEED
2005-01-31
DIMENSIONS
Total length
Technical Specification
4-100 S-C
2004-05-12
B 14 F Boom
Feed Swing
Feed Extension
Boom Swing
Feed Tilt
Boom Lift
Ensure horizontal //
Ensure vertical //
APPLICATION DESCRIPTION
B 14 F boom is designed for Tamrock Quasar jumbos. The x-y coordinated boom movements together with
360° actuator roll-over make the use of the boom simple
B 14 F boom is a hydraulic universal roll-over boom for
and logical. Accurate automatic parallel holding both in
mechanized tunnelling, drifting, cross-cutting and bolt-
vertical and horizontal plane improves the drilling
hole drilling in medium sections. It can also be used for
performance and accuracy.
production drilling with cut-and-fill and room-and-pillar
methods. Large dimensioned rectangular profile, large diameter
bearings, sealed main joints, expanding pins in cylinder
This parallel holding boom offer large «true» rectangular
joints and use of super strong cast pieces in most
face coverage area.
stressed areas are some of the features that are
included to the boom design for improved reliability.
TECHNICAL DATA
Coverage with parallelism holding 17,6 m²
Coverage with manual override 25,8 m²
Weight, without hoses 1 350 kg
Weight allowed 800 kg
Boom lift, up and down 40° and 20°
Boom swing, symmetric ± 36°
Feed tilt, up and down 27° and 45°
Feed swing, symmetric ± 40°
Divergence, up and down 3° and 90°
Feed extension 2 000 mm
Feed roll-over 360°
Technical Specification
4-100 S-C
2004-05-12
B 14 F Boom
COVERAGE AREA
2900
2100
1880 1805
4500
5500
GENERAL DIMENSIONS
60°
5°
40°
2000
2000 170
90° 356
360°
45°
29°
1193 27°
16° 27°
36°
40°
40°
36°