LVVTA STD Suspension Systems
LVVTA STD Suspension Systems
…………………………………………………………………….……………………………… ……………………….……………………………………………………………………
5
Note that highlighted text shows amendments that have been made subsequent to the document’s previous issue, and a
grey vertical stroke to the left of the text denotes information that is of a technical (rather than a formatting) nature.
Overview
Background
The Low Volume Vehicle Technical Association Incorporated (LVVTA) represents ten specialist
automotive groups who are dedicated to ensuring that vehicles, when scratch-built or modified,
meet the highest practicable safety standards. The information in these standards has stemmed
from work undertaken by LVVTA founding member organisations that commenced prior to 1990
and has been progressively developed as an integral part of NZ Government safety rules and
regulations by agreement and in consultation with the New Zealand Transport Agency. As a result,
the considerable experience in applied safety engineering built up by LVVTA and the specialist
automotive groups over the past twenty years can be of benefit to members of the NZ public who
also wish to build or modify light motor vehicles.
Copyright
The content of this document remains the property of the Low Volume Vehicle Technical
Association (Inc.), and no part of it may be reproduced without the prior written consent of the
copyright holder.
Associated information
Other associated information relevant to the subject matter contained in this low volume vehicle
standard, which in the interest of comprehensiveness, should be read in conjunction with this
standard, includes:
LVVTA News June-September 2013 Issue 47 Page 4 Chinese Bearings in American Stub Axles
LVVTA News June-September 2013 Issue 47 Page 6 Aftermarket Mustang II-based Custom IFS
‘Dog-bone’ Mounting System
LVVTA News June-September 2013 Issue 47 Page 7 ‘Heidts’-brand Suspension Arm Issue
LVVTA News June-September 2013 Issue 47 Page 9 Update of LVVTA-recognised IFS
Manufacturers
LVVTA News October-December 2013 Issue 48 Page 1-4 Raising the Hard Questions (raised vehicles)
LVVTA News October-December 2013 Issue 48 Page 9 Faulty Threads on Aftermarket Suspension
Arms
LVVTA News October-December 2013 Issue 48 Page 11 Inspecting Modified Vehicles with ‘Airbag’
and ‘Hydraulic’ Suspension Systems
LVVTA News January-July 2014 Issue 49 Page 12 Lowered Suspension LVV Inspection Basics
LVVTA News August-December 2014 Issue 50 Page 2 Suspension ‘Johnny Joints’
LVVTA News August-December 2014 Issue 50 Page 4 Check for Drilling of I-beam Axles
LVVTA News August-December 2014 Issue 50 Page 8 Custom Suspension Arms Info-sheet # 01-2012
Reminder
LVVTA News May-July 2015 Issue 52 Page 6 Lock Washers on Adjustable Camber Plates
LVVTA News May-July 2015 Issue 52 Page 6 Dome-style Rubber Cushions as Bump-stops
LVVTA News May-July 2015 Issue 52 Page 9 Recognised IFS Manufacturers (covers IRS &
welded brake calipers)
LVVTA News May-July 2015 Issue 52 Page 9 Custom Bushed Rod Ends
LVV Information Sheet # 05-2004 Upper Suspension Ball-joints in Early Ford Falcons
and Fairlanes
LVV Information Sheet # 05-2008 Air Cylinder Suspension Systems
LVV Information Sheet # 08-2008 I-beam Axles and Split Radius Rods
LVV Information Sheet # 02-2009 Spring and Hub-carrier Adjustable Suspension
Note that all documents referred to in this table, with the exception of the NZ Car Construction Manual, can be accessed
from www.lvvta.org.nz free of charge. For information on obtaining the NZ Car Construction Manual, contact
[email protected]
Note also that paper copies of documents can become out of date and as such should not be relied upon, therefore
LVVTA advises users of this standard to check to ensure that the Associated Information listed here is current, by going to
www.lvvta.org.nz/standards.html
Contents
Purpose of this standard Page 6
The purpose of this standard is to specify requirements which motor vehicles must meet when safety-
related suspension modifications are carried out, in order to ensure that satisfactory handling
characteristics are present in all normal driving conditions.
1.1(1) This low volume vehicle standard applies to all light vehicles other than those
specified in 1.1(2), that are:
(a) modified on or after 1 January 1992 in such a way that any suspension
systems may, directly or indirectly, be affected; or
1.1(2) This low volume vehicle standard does not apply to:
1.2(1) A light vehicle that is modified or scratch-built as in 1.1(1), becomes a low volume
vehicle, and must:
NOTE: Where a light vehicle is required to be certified to the Low Volume Vehicle Code, but the modification date
precedes the date upon which this standard takes effect (1 December 2000), an LVV Certifier must ensure
that the vehicle meets the general safety requirements contained in 2.1 of this standard, and should use
the applicable technical requirements of section 2 of this standard as a guideline upon which to base his
judgements on the safety of the vehicle.
(a) be designed and constructed using materials and components that are fit
for their purpose; and
NOTE: The requirements specified in 2.1(1) are selected from 2.3 of Part 2 of the Low Volume Vehicle Code,
reproduced here in the interest of convenience, and are over-riding requirements which make it clear
that, regardless of what technical requirements are or are not in place, every vehicle certified to the Low
Volume Vehicle Code must be fit for its purpose, and must be safe.
2.1(2) A steering system on a motor vehicle, and associated systems and components
that could directly or indirectly affect the directional control of the vehicle, must:
(a) provide the vehicle with safe, efficient, convenient, and sensitive control;
and
(b) be strong, durable, and fit for its purpose, taking into account whether
adverse effects have resulted from a loss of integrity of any protective
system used by a relevant component.
NOTE: The requirements specified in 2.1(2) are the applicable general safety requirements from 2.2(1) and 2.2(2)
of Land Transport Rule 32003: Steering Systems 2001 which are required as part of this low volume vehicle
standard, and are reproduced here in the interest of convenience.
2.2(1) All low volume vehicles, except those specified in section 3, must comply with the
applicable requirements in 2.2 and 2.3.
2.2(2) A low volume vehicle that is either scratch-built, or has had its suspension system
modified to such an extent that the modifications are beyond the scope of this
low volume vehicle standard, must, in addition to this standard, comply with the
relevant suspension design and construction requirements specified in Chapter 6
Suspension Systems of the New Zealand Car Construction Manual.
Suspension travel
2.2(3) Suspension travel available within a low volume vehicle must be such that:
(a) no interference is likely to occur between the underside of the body and
any drive-shafts or other drive-line components during full suspension
movement; and
(c) the minimum distance that the suspension extends from static ride
height is either:
(i) 40 mm; or
NOTE: An unusual vehicle as referred to in 2.2(3)(c)(iii) may be one with an unusually small amount of suspension
travel such as a scratch-built Lotus 7 replica.
2.2(4) No components fitted to a low volume vehicle other than chassis or sub-frame
cross-members and non-structural body panels, may be positioned below a
straight line which extends from the bottom of any wheel-rim to the opposite
side tyre-to-ground contact point.
2.2(5) Tyres and wheel-rims fitted to a low volume vehicle must be positioned in such a
way that they cannot contact any part of the vehicle to which they are fitted,
other than the point of attachment, throughout the full range of steering and
suspension movement during normal vehicle operation.
2.2(6) A suspension system incorporated within a low volume vehicle may be modified
to raise or lower the ride-height of a vehicle, provided that:
Bump-stops
2.2(7) A low volume vehicle must be fitted with purpose-designed bump-stops that:
(d) limit the suspension travel before the ball-joints have reached the end of
their effective travel; and
(e) prevent contact between the underside of the vehicle and the road
surface during vehicle operation when fully laden.
NOTE 1: The purpose of a bump-stop is to avoid shock-load damage upon bottoming out under full suspension
compression. A rubber donut-type buffer-stop is acceptable, and can be incorporated into coil-over
shock absorbers that do not have one already fitted.
NOTE 2: A short dome-style rubber cushion meant as a full-droop stop on a suspension arm is not acceptable for
use as a suspension bump-stop.
Geometry
2.2(8) Moving components and systems fitted to a low volume vehicle which are
affected by suspension travel, must not be detrimentally affected at extremes of
suspension travel by exceeding the operating limits specified by the equipment
manufacturer, including:
2.2(9) A low volume vehicle, except in the case of a vehicle for which a current and valid
LVV Authority Card has been issued, which has undergone significant changes to
the suspension system must feature no abnormal suspension geometry, and be
aligned so as to provide satisfactory handling characteristics, and ensure against
excessively shortened tyre life.
NOTE 1: An ‘LVV Authority Card’ as referred to in 2.2(10) is an authority card issued by Motorsport New
Zealand for authorised competition licence-holders.
NOTE 2: Proof of compliance with the requirement specified in 2.2(9) is a full four-wheel alignment report.
2.2(10) A front or rear suspension system in a low volume vehicle, except in the case of a
vehicle which is primarily designed and used for LVVTA-recognised motor sport
events, and for which a current and valid LVV Authority Card has been issued,
must incorporate no more than either:
(b) one half of a degree of negative camber more than the maximum figure
specified by the vehicle manufacturer, including any manufacturer-
specified tolerance.
NOTE 1: Where negative camber does not exceed 1.5 degrees when measured by the LVV certifier, the
requirement for a wheel alignment report is not mandatory, unless specifically required by the LVV
Certifier.
NOTE 2: An ‘LVV Authority Card’ as referred to in 2.2(10) is an authority card issued by Motorsport New
Zealand for authorised competition licence-holders.
2.2(11) A wheel-rim fitted to a modified production low volume vehicle which retains the
vehicle manufacturer’s original wheel hub assembly must not have the wheel-rim
centre offset by any more than 35% of the total wheel-rim width.
Shock absorbers
2.2(12) A low volume vehicle must have a method of effectively dampening road shock
for each wheel, which is able to satisfactorily control suspension spring energy.
(a) compatible in stroke and rate to the spring with which it operates; and
(b) of a size and rate which is appropriate for the weight and intended use of
the vehicle to which it is fitted.
(a) be of a size and rate that is appropriate for the weight and intended use
of the vehicle to which it is fitted; and
(b) in the case of a spring that reduces the suspension travel and, as a result,
reduces the ride height of the vehicle, be proportionately increased in
stiffness rate so as to ensure against premature bottoming-out during
normal vehicle operation when the vehicle is fully laden.
(a) incorporate springs that have sufficient coil spacing to ensure that coil
bind does not occur at full suspension travel; and
2.2(16) Coil springs fitted to a low volume vehicle must be designed in such a way that
the ends of the springs, whether of a plain, plain and ground, closed, or closed
and ground configuration, are shaped to match the surfaces against which they
seat, both top and bottom.
2.2(17) Progressive-rate coil springs must have the closely-wound section of the coil
positioned either:
2.2(18) Coil springs fitted to a low volume vehicle must be firmly contained within their
locating seats in such a way that the springs cannot move vertically, or become
dislodged when the suspension travel reaches its maximum rebound, limited by
either:
2.2(19) Coil springs fitted to a low volume vehicle must not be modified for the purpose
of changing the vehicle’s ride height unless either:
2.2(20) A coil spring fitted to a low volume vehicle may only be electro-plated if the
electro-plating is carried out in accordance with the relevant specifications in
Chapter 6 Suspension Systems of the New Zealand Car Construction Manual.
2.2(21) With the exception of the removal or refitting of one or more leaves within a leaf
spring, a leaf spring fitted to a low volume vehicle may only be manufactured or
modified by a recognised industry expert who is professionally engaged in the
manufacturing and modification of springs.
NOTE 1: A leaf spring may be heated and reset in order to reduce the ride-height of a low volume vehicle,
provided that the work is carried out by a person referred to in 2.2(21).
NOTE 2: The spring eyes of a leaf spring fitted to a low volume vehicle may be reversed provided that the work
is carried out by a person referred to in 2.2(21).
NOTE 3: In the case of a leaf being removed from a spring pack, an LVV Certifier must ensure that the
requirement for suitable spring stiffness in 2.2(14) remains.
2.2(22) A low volume vehicle must not be lowered by the fitting of leaf springs mounted
in the upside-down position.
2.2(23) A low volume vehicle fitted with a leaf spring suspension system, which uses
extended spring shackle pin sets to achieve an increase in suspension height,
must have shackle pin sets that, if longer than 150 mm between shackle pin
centres, are reinforced to prevent bending under cornering loadings.
2.2(24) Spacer blocks which have been fitted to leaf spring suspension systems to raise or
lower the ride height of the vehicle, must be of a depth no greater than:
2.2(25) A spacer block fitted to a leaf spring suspension system to raise or lower the ride-
height of a low volume vehicle must be:
(a) positively located at the top and the bottom of the block; and
(c) firmly seated over not less than the original seat area; and
2.2(26) Over-ride airbags, when fitted to assist the springs on a low volume vehicle when
the vehicle is heavily laden, must:
(a) where fitted in place of a bump stop, incorporate an effective bump stop;
and
NOTE: The over-ride airbag manufacturer’s installation instructions may be used as a guide for correct mounting,
provided that all technical requirements contained within this standard are met.
2.2(27) A suspension strut that is adjustable to raise and lower the vehicle ride height
must:
NOTE: A second locking ring is a ‘suitable mechanical locking device’ as referred to in 2.2(27)(b). A thread-lock
adhesive is not acceptable.
2.2(28) A non-adjustable strut modified by removing most of the strut tube down to the
stub axle and sliding over a replacement threaded strut tube for the attachment
of an adjustable spring platform, must:
(a) not incorporate any modification of, or welding to, any cast or forged
component, in particular the stub axle assembly; and
(b) have the threaded strut tube press-fitted over the original remaining
strut tube with no less overlap than the length of one diameter of the
tube; and
(c) have the threaded strut tube fully welded to the original remaining strut
tube, around the circumference of the lower end, with plug welds above;
and
(d) meet the requirements specified in section 18.9 of Chapter 18 of the New
Zealand Car Construction Manual for critical function welding.
NOTE 1: A weld referred to in 2.2(28)(c) is considered to perform a critical function, and as such must meet the
requirement for critical welds, including TIG welding, with an associated non-destructive test.
NOTE 2: Any welding of the strut tube should be no closer than 10 mm to any casting or forging.
NOTE 3: The plug welds referred to in 2.2(28)(c) should consist of not less than two 10 mm plug welds, or four
8 mm plug welds.
2.2(29) A non-adjustable strut modified by replacing the fixed OE spring platform with a
threaded sleeve and adjustable spring platform that is fitted to a low volume
vehicle must either:
(a) have the threaded sleeve fully-welded to the strut tube around the top
and bottom circumferences, and meet the requirements specified in
section 18.7 of Chapter 18 of the New Zealand Car Construction Manual
for general welding; or
(b) where the strut tube has been shortened by cutting and re-welding, have
the threaded sleeve positioned across the joint and be fully-welded to
the strut tube around the top and bottom circumferences, and meet the
requirements specified in section 18.9 of Chapter 18 of the New Zealand
Car Construction Manual for critical function welding.
NOTE 1: A weld referred to in 2.2(29)(a) is not considered to perform a critical function, and as such does not
need to meet the requirement for critical function welds in section 18.9 of the NZ Car Construction
Manual, however an LVV Certifier may require, at his discretion, a non-destructive test (NDT)
following a visual inspection.
NOTE 2: In the case of where 2.2(29)(a) applies, to prove the tube has not been cut and welded, a modifier
should have the strut inspected by an LVV Certifier before the strut is reassembled.
2.2(30) An aftermarket suspension strut fitted to a low volume vehicle that incorporates
adjustment on the upper platform mount to adjust geometry, must use the same
number of fasteners as supplied by the upper platform mount manufacturer.
NOTE: In the case where upper platform mounts are incorporated within aftermarket McPherson-style struts
(which usually incorporate 4 or 6 fasteners), additional anti-vibration devices (as required by Chapter 18
Attachment Systems of the NZ Car Construction Manual) are not required in this specific situation,
provided that the upper platform mount is installed in accordance with the manufacturer’s instructions
and the fastening equipment is that which is provided by the upper platform mount manufacturer.
2.2(31) A suspension arm that is fitted to a low volume vehicle which is a volume-
produced aftermarket bolt-in type, and which is mounted directly to the vehicle’s
unmodified original suspension attachment points therefore maintaining all
original suspension geometry, other than to allow additional adjustability, must:
(a) follow sound time-proven designs, and be consistent with the common
time-proven makes; and
(c) be of an appropriate size for use with the weight and performance
characteristics of the vehicle to which it is fitted; and
(d) in the case of a suspension arm which supports the weight of the vehicle:
NOTE: ‘Documented brand verification’ as referred to in 2.2(31)(d)(ii) means some form of documented
verification that the arm is in fact a known and recognised brand of volume aftermarket manufacturer,
and can be an invoice (preferred) or advertising material that clearly shows the listed parts being identical
to those being assessed.
2.2(32) In the case of a suspension arm fitted to a low volume vehicle that supports the
weight of the vehicle which is produced by an unrecognised or unidentified
aftermarket suspension component manufacturer, the arm must:
(a) meet or exceed the material specifications for aftermarket and custom
suspension arms provided in Chapter 6 Suspension Systems of the New
Zealand Car Construction Manual; and
NOTE 1: For requirements relating to other types of suspension arm modifications, including custom or one-off
arms that are outside of the scope of this standard, and for guidance on appropriate sizing, Chapter 6
Suspension Systems of the NZ Car Construction Manual should be referred to.
NOTE 2: Where any doubt exists in relation to any aspect of an aftermarket suspension arm during the LVV
certification assessment process, an LVV Certifier should use Chapter 6 Suspension Systems of the NZ
Car Construction Manual as a source document for guidance, and as part of that assessment process
may elect to refer the component to the LVVTA Technical Advisory Committee for approval.
Suspension joints
(a) either:
and
(b) be connected to the suspension arm with sufficient strength, taking into
consideration the applied load-paths through the ball-joint, and the
forces to which the connection will be subjected.
2.2(34) A spherical bearing rod-end joint fitted to a low volume vehicle must:
(b) be positioned in such a way that binding of the end cannot occur
throughout the full range of suspension travel; and
(c) incorporate sufficient thread engagement to ensure that the rod end is
securely held in position; and
(h) where the joint is a screw in/out custom spherical bearing rod-end, only
be loaded in compression or tension through its longitudinal axis.
NOTE 1: A spherical bearing rod-end joint is also commonly referred to within the automotive hobby and
industry as a ‘rose-joint’ or ‘heim-joint’.
NOTE 2: ‘Radial load-rating’ (appropriate to rod-end size) as specified in 2.2(34)(a) is to be assessed by referring
to Table 6.3 in Chapter 6 Suspension Systems of the NZ Car Construction Manual.
(d) where the rod-end joint is a screw in/out bushed rod-end, only be loaded
in compression or tension through its longitudinal axis.
Stub axles
2.2(36) A stub axle fitted to a low volume vehicle may be replaced, provided that:
and
(ii) an integral part of the stub axle and enables correct steering
geometry to be retained.
NOTE 1: A ‘stub axle’ is also commonly referred to within the automotive hobby and industry as an ‘upright’.
NOTE 2: The common ‘bolt-on original equipment-style of stub axle’ referred to in 2.2(36)(a) includes an OEM-
type 4-stud to 5 stud stub axle conversion or an OEM conversion from drum to disk brake that includes
stub axle replacement.
NOTE 3: A stub axle that does not meet the above criteria, such as a custom made part or one that cannot be
identified as being from a reputable manufacturer, is outside the scope of this standard and must be
evaluated using the NZ Car Construction Manual.
NOTE 4: An LVV Certifier may require an aftermarket stub axle to undergo a nodularity test if he has reason to
believe that the axle may not have sufficient ductility to be fit for its intended purpose.
Other requirements
2.2(39) A low volume vehicle required to comply with this standard must also comply
with the relevant requirements of:
(d) Chapter 7 Steering Systems of the New Zealand Car Construction Manual.
NOTE: The reference to LVV Standard 125-00 (Lighting Equipment) in 2.2(39)(b) is because the raising or
lowering of a vehicle could, in extreme cases, cause lighting equipment to fall outside of permitted areas.
Vehicle operation
2.3(1) A modified production low volume vehicle with modified suspension systems
must perform in a manner which preserves at least the quality of steering control
which could be reasonably expected when the vehicle was manufactured.
2.3(2) A scratch-built low volume vehicle must perform in a manner which gives a
quality of steering control at least equal to that expected of production vehicles
of similar purpose and performance.
2.3(3) A low volume vehicle must handle in a manner which allows good steering
control in all normal driving conditions, including:
(b) progressive and positive feel with no kick-back through the steering
wheel during turn-in and turn-out; and
(f) no tendency to climb the road camber toward the opposing lane.
2.3(4) Shock absorbers with adjustable damping rate fitted to a low volume vehicle
must achieve acceptable ride and handling when tested in the firmest available
setting, except in the case of a vehicle which is primarily designed and used for
LVVTA-recognised motor sport events, and for which a current and valid LVV
Authority Card has been issued.
NOTE: An ‘LVV Authority Card’ as referred to in 2.3(4) is an authority card issued by Motorsport New Zealand
for authorised competition licence-holders.
2.3(5) Any low volume vehicle with lowered suspension may be inspected and tested,
where considered necessary at the discretion of the LVV Certifier, in a condition
of simulated occupant weight and load, on the following basis:
(a) a Class MA, MB, MC, MD1, and MD2 low volume vehicle carrying 80 kg
distributed in each seating position; and
(b) a Class NA low volume vehicle carrying the difference between the tare
weight of the vehicle and the manufacturer’s gross vehicle mass rating at
the forward-most section of the load floor.
2.3(6) The suspension height of a low volume vehicle must be measured and recorded,
as an average figure of the front wheel heights and of the rear wheel heights, by
the LVV Certifier at the time of LVV certification inspection:
(a) from the centre of each wheel up to the underside of the guard directly
above, as shown in Diagram 2.3(6); and
(b) with the vehicle on a flat surface, with the vehicle unladen and no
occupants; and
(c) where a vehicle with guards that extend lower than the centre of the
wheel, from the centre of each wheel down to the bottom edge of the
guard, with a negative figure recorded.
GW illustration
Geometry exclusion
3.1(1) A low volume vehicle which is primarily designed and used for LVVTA-recognised
motor sport events, and for which a valid and current LVV Authority Card is
issued, is not required to comply with the requirements specified in 2.2(9) and
2.2(10).
3.1(2) A low volume vehicle which is primarily designed and used for LVVTA-recognised
motor sport events, and for which a valid and current LVV Authority Card is
issued, is not required to comply with the road-test shock absorber setting
requirement specified in 2.3(4).
NOTE: An ‘LVV Authority Card’ as referred to in 3.1(1) and 3.1(2) is an authority card issued by Motorsport New
Zealand for their association members who are authorised competition licence-holders.
4.1(1) A light vehicle is not required to be certified to this low volume vehicle standard,
if the vehicle is modified for the purposes of law enforcement or the provision of
emergency services.
4.1(2) A light vehicle is not required to be certified to this low volume vehicle standard,
if the vehicle is identified as having been modified by a second-stage vehicle
manufacturer, and complies with an approved overseas standard that is listed in
Annex 6 of the Low Volume Vehicle Code.
4.2(1) A modified production low volume vehicle is not required to be certified to this
low volume vehicle standard, if the vehicle was:
(a) modified before 1 January 1992 in such a way that any suspension
system may, directly or indirectly, be affected; and
(b) the suspension system fitted to the vehicle is the same as that which was
fitted at the time of the vehicle’s modification.
4.2(2) A scratch-built low volume vehicle is not required to be certified to this low
volume vehicle standard, if the vehicle was:
(b) the suspension system fitted to the vehicle is the same as that which was
fitted at the time of the vehicle’s construction.
4.3(1) A vehicle is not required to be certified to the Low Volume Vehicle Code where a
suspension modification is the sole modification, and the following criteria are
met, provided that the safe performance of the vehicle is not compromised:
(a) after-market shock absorbers including air adjustable units but not
including those with height-adjustable platforms, may be used provided
they fit unmodified OE mountings; or
(b) after-market road springs, including those that raise or lower the vehicle,
may be substituted for the originals provided that the springs or shock
absorbers are direct replacements, and:
(iv) springs and spring seats are not height adjustable by any means
(unless original equipment); and
(vi) the normal relationship between the front and rear suspension
height is not unduly affected; and
or
(c) if blocks are used in leaf springs to adjust their ride height (up or down)
and the suspension has not been raised by any other means, the blocks
must be:
(ii) firmly seated over not less than the OE seat area; and
or
or
(e) after-market anti-sway bars may be fitted provided the bar is attached to
unmodified OE mounting points; or
(g) suspension braces (strut tower braces) may be fitted provided there are
no structural changes to the body or suspension mounting points; or
(ii) are a catalogued aftermarket item for that make and model of
vehicle.
Bump-stop means a resilient block, usually rubber, that is contacted by the suspension at the
extreme limits of travel.
NDT is an abbreviation for non-destructive testing, usually used to check that a weld
does not have any flaws, cracks or features of the design that may weaken the
joint.
Offset means the distance between the vertical centreline of the wheel, and the hub
flange to which the wheel attaches.
NOTE: The terms and definitions found in section 5 are limited to those terms and definitions that are unique to
this low volume vehicle standard, and are not necessarily contained within the terms and definitions
section of the Low Volume Vehicle Code.