Schindler 5500/5500S/5400-Rel.02: EN81-1 Commissioning Manual K 40700039 - 12 Edition 02-2016
Schindler 5500/5500S/5400-Rel.02: EN81-1 Commissioning Manual K 40700039 - 12 Edition 02-2016
02
EN81-1
Commissioning Manual
K 40700039_12
Edition 02-2016
NOTICE
Installation Requires Schindler 5500 Certification
Installers must be Schindler 5500 certified according to J 43401269.
The installers have already proven skills in and knowledge of:
Safety during installation Z07a classroom
Basic elevator know-how Z08
Basic know-how on elevator installation Z06
Safety on site, risk assessment, use of installation guides, and embedded documents. See K 43402271.
Modification: 11 12
Table of Contents
1 General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.1 Safety Advice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.2 Electrical Hazards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2 Standard Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.1 Reset Procedures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.2 Inspection Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3 Preparation for Installation Travel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.1 Prerequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.2 Controller Cabinet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4 Brake Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.1 Brake Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5 Motor Control Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.1 Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.2 Parameter Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5.2 Parameter Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.3 Fan Test ACVF and Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
5.4 DC Link Test and Current Loop Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
5.5 Zero Position Test (PML 160/200) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
6 Installation Travel with ESE Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
6.1 Installation Travel with ESE Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
7 Installation Travel with REC Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
7.1 Prerequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
7.2 Car . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
7.3 Installation Travel with REC Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
7.4 Door Drive Connection and AutoSetup (V15/35 without landing door coupled) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
7.5 Door Drive AutoSetup (V15/35 with landing door) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
7.6 Special Setting for Heavy Doors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
7.7 Special Setting for Landing Doors with Different Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
8 Manual Evacuation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
8.1 PEBO - Pulsed Electric Brake Opening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
16.1 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
17 ETMA Tele-Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
17.1 ETMA Tele-Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
18 Embedded Telemonitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
18.1 Embedded Telemonitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
19 Checking of Automatic Evacuation (AES) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
19.1 Checking of Automatic Evacuation (AES) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
20 User Interface SMLCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
20.1 Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
20.2 Switches and Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
20.3 Main Menu SMLCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Safety Instructions
WARNING
Exclusively for competent professionals.
Current version of the safety manual and
any local safety requirements must be The safety warning with the signal word
consulted and followed before initiating “Warning” is used to indicate a hazardous
works. situation which, if not avoided, could result in
Personal Protective Equipment: death or serious injury.
– Always use and maintain the listed
personal protective equipment.
– Immediately replace damaged or lost
NOTICE
personal protective equipment.
DANGER
DANGER NOTICE
Hazardous Voltage Components Sensitive to Electrostatic Discharge (ESD)
Contact with live parts will result in electric shock causing serious injury ESD-sensitive components will be destroyed if exposed to electrostatic
or death. discharge.
Do not touch live parts. If handling ESD-sensitive components: Adhere to ESD-safe
Switch off the main switch and de-energize the installation procedures.
completely before starting to work on the installation.
WARNING
Bypassing of Safety Devices and Safety Contacts
Bypassing of safety-relevant devices can result in damage to the
installation or in serious injury or death.
Do not bypass the safety circuit without explicit instruction.
If bypassing is premeditated for specific work: Take appropriate
safety measures.
Do not bypass safety devices if prohibited by local code.
If safety devices are bypassed: Disable the installation.
NOTICE
Plugging/Unplugging Connectors on Energized Devices
Hot plugging can result in the destruction of devices.
Switch off the devices before plugging in or unplugging
connectors.
Switch off JH, SIL and SIS, see the wiring diagram. Connector Description
AS.ASIXB: Check that the connector BATT is unplugged.
HK Traveling cable
If MRL: Check that the switch JH1 is set to ON.
GNT Intercom device
If S.PEBO: Check that the BATT1 and BATT2 plugs are unplugged.
LOP Landing supply and bus
AS.ASIXB: Set the rotary switch elevator ID according to the
installation. AS.GCIOCF: Check that the connector ETHERNET is unplugged.
Position Description AS.CLSD: Check that the following connectors are unplugged:
1 Elevator 1 or simplex Position Description
2 Elevator 2 TT PSTN input telephone line
3 – TT* PSTN input alarm line
AS.ASIXB: Set switch JMOF to position 1. AS: Check that the traveling cable connector POWC is not
Check that the installation chip card is plugged into the user connected to the X1 terminal bar (X1-1-1 terminal).
interface.
If transformer TA: Check that the transformer is connected Some connectors have temporary or permanent bridges.
according to the wiring diagram.
If options are not needed during commissioning: The related
If transformer TAS: Check that the transformer is connected to the connectors are bridged temporarily.
X1 terminal bar, see the S 274901 Wiring Diagram - Mains Power If options are not needed in normal operation: The related
Supply. connectors are bridged permanently.
If no TAS: Check that bridges are present between X1-4-1:
Pins 1-5 and 3-6, see the S 274901 Wiring Diagram - Mains Power AS.ASIXB:
Supply. If present: Plug in the following connectors:
If not: Replace the following connectors by bridges:
AS: Plug in the following connectors:
Connector Description Connector Description
PEBO.KBV Overspeed governor contact ARD Phase control relay
KBVG Counterweight overspeed governor PEBO_SK Manual electric rescue device
EM If MRL: Evacuation interface SKS Hoistway safety circuit
Jumper plug, plug kit ID no. 59325720
PEBO If MRL: Evacuation interface
HK Traveling cable
AS.ASIXB: Plug in the following connectors, see the wiring Jumper plug, plug kit ID no. 59325720
diagram: KBV Overspeed governor contact
Connector Description KTHS Hoistway temperature sensor
ESE Recall control station LDBCS If Hong Kong:
KSS/KSS1 Slack rope device Landing door bypass control
Bridges between pins 1-2 and 5-6
KV Permanent bridge
AS.BCM: Check that the connectors POWIN and MGB are not Switch off JH, SIL and SIS.
plugged in. AS.ASIXB: Plug in NGL.
Check that the machine and the ACVF are installed according to AS.ESE: Set the following switches to position:
the installation documents.
Switch Position
Check the mains supply from the building site on the switches JH
and SIL line side. JRH RECALL
Switch on JH, SIL and SIS. JHM STOP
Switch on SIBS and JLBS. If Korea: JUEKTS NORMAL
Check that the hoistway lighting is on.
If Korea: Insert NORMAL bypass connector.
SIBS and JLBS remain switched on during the whole
Switch on JH, SIL and SIS.
commissioning procedure.
- The system boots. Booting takes a few minutes.
FC: Check the following LED status: - If no chip card expansion has been performed: The LED CCS
blinks.
Color Name Status
Red ERROR OFF
Green OK OFF
Yellow PARAMETER ON
AS.GCIOCF: Check the following LED status: Check the following LED status:
Color Name Status Color Name Status
Green STATUS OFF Red ERROR OFF
Green CPU FAST BLINKING Green OK ON
Green WDOG BLINKING Yellow PARAMETER OFF
Red ERROR OFF
SMLCD: Check the software versions:
Switch off JH, SIL and SIS. Login → Status → Versions → GC-Software and Drive-Software.
AS.ASIXB: Plug in connector RS422. Switch off JH and SIS.
Switch on JH and SIS. AS.ASIXB: Plug in the connector BATT.
Wait until the boot sequence is completed.
AS.GCIOCF: Perform a double reset.
- The control SW sends the drive settings and parameters to the
frequency converter.
AS.BCM:
DANGER Check that no plug is inserted in connector MGB_TEST.
Elevator Operation with Defective Machine Brake AS.ASIXB:
Operating an elevator with defective brakes will result in damage to the Check that cable KB is not connected.
installation or in serious injury or death. AS.BCM:
If the brakes are defective: Check the resistance on the MGB cable:
Stop commissioning actions.
Put the elevator out of service immediately. Machine Type Pins Coil Resistance
Inform your supervisor. 1-6 MGB
2-5 MGB1
The mechanical brake is factory adjusted. 190 ... 1700 Ω
FML/PML 160/200 3-6 MGB2
If a test fails:
4-5 MGB3
Do not readjust the mechanical brake.
1-2-3-4-5 - High resistance MΩ
Refer to the maintenance instructions of the hoisting machine
to ground
to solve the problem.
1-6 MGB
AS: Set the following switches to position:
FMR/PMR 160/200 2-5 MGB1 80 ... 120 Ω
Switch Position and PMB 140
JH OFF 1-2-3-4-5-6 - High resistance MΩ
SIS OFF to ground
JRH RECALL 1-5 MGB
60 ... 80 Ω
JHM STOP PMB 130 2-6 MGB1
1-2-3-4-5-6 - High resistance MΩ
AS.BCM: to ground
Check that the cables POWIN and MGB are not connected.
AS.ASIXB: Check the resistance on the KB cable: AS, ASIXB(K): Check the following LED status:
Machine Type Pins Contact Resistance Color Name Status
1-2 KB closed Approximately 0 Ω Green ZSB OFF
1-3 KB1 open High resistance MΩ Green SB1 ON
1-4 KB2 closed Approximately 0 Ω Green SB ON
FML/PML 160/200
1-5 KB3 open High resistance MΩ Green KB3 OFF
1-2-3-4-5 - High resistance MΩ Green KB2 ON
to ground Green KB1 OFF
1-2 and KB closed Approximately 0 Ω Green KB ON
1-4
FMR/PMR 160/200 1-3 and KB1 open High resistance MΩ Switch off JH and SIS.
and PMB 130/140 1-5
1-2-3-4-5 - High resistance MΩ
to ground
AS.ASIXB:
Check the switch JMOF is on position 1.
* NTSD function (Normal Terminal SlowDown) required for Singapore and India codes.
Motor Control Tests DC Link Test and Current Loop Test K 40700039_12 22
Copyright © 2016 INVENTIO AG
5 Motor Control Tests
5.5 Zero Position Test (PML 160/200)
The zero position test detects any deviation between the rotor position
and the motor encoder position. It determines at which degree of the NOTICE
motor encoder sine wave the motor poles are aligned. If the Incorrect Test Procedure
counterweight is loaded with the full load: The zero position test
Aborting the test procedure or performing the test procedure in a
changes the phase direction to (0 or 1) or (2 or 3). The duration of the
different sequence will result in incorrect values. Incorrect values can
zero position test can be different at every attempt, even if performed at
affect the normal operation of the elevator.
the same hoistway position.
Do not deviate the step sequence.
Do not abort the test procedure.
Preconditions
The safety circuit is closed.
MH is of synchronous type. SMLCD: Execute the zero position test.
The motor ID parameter recognizes the MH. Login → Tests → VF test → ZeroPositionTest → OK.
MH is equipped with a sine wave encoder. Wait until the SMLCD displays "ZeroPositionTest - OK?":
The motor encoder type parameter recognizes the MH. - The system is ready for test travels.
The DC link and current loop test have been performed Press the button OK on the SMLCD.
successfully.
Wait until the message "Begin Test" appears.
The car is positioned > 3 m below headroom or machine room
level. During the zero position test, the car can travel > 2 m in the Press and hold the button DRH-D or DRH-U until the car has
up direction. stopped.
If emergency: Release the button DRH-D or DRH-U.
Release the button DRH-D or DRH-U and wait for 3 to 5 seconds.
Repeat the last three steps until the SMLDC displays
"ZeroPositionTest - Success".
Several trips are required. If the test does not perform correctly:
Refer to the ACVF diagnostics documentation.
Increasing or Decreasing Recall Travel Speed Increasing or Decreasing Inspection Travel Speed
Press the button JHM. Press the button JHC.
Set the switch JRH to RECALL. Set the switch JREC to INSPECTION.
To decrease: Press the button DRH-D for maximum 10 seconds. To decrease: Press the button DREC-D for maximum 10 seconds.
To increase: Press the button DRH-U for maximum 10 seconds. To increase: Press the button DREC-U for maximum 10 seconds.
Release the switch JHM. Release the switch JHC.
Pressing DRH-D or DRH-U for more than 10 seconds sets the
recall travel speed to the minimum or maximum value.
Installation Travel with ESE Control Panel Installation Travel with ESE Control Panel K 40700039_12 25
Copyright © 2016 INVENTIO AG
6 Installation Travel with ESE Control Panel
6.1 Installation Travel with ESE Control Panel
AS: Set the switch JMOF to position 1. Installation Travel Without Car Node
Set the switch JRH to RECALL. To complete the hoistway installation without car node, the ESE control
Press the button JHM. panel is moved to the car roof. This allows the car to be moved from the
Switch on JH, SIL and SIS. car roof.
Wait until the boot sequence is completed.
AS: Release the switch JHM. Support Equipment
Plug kit: ID no. 59325720
Move the car some centimeters to check if the car travels in the
correct direction.
Press DRH-D: The car travels downward. Procedure
Press DRH-U: The car travels upward. Move the ESE control panel to the car roof:
If the car travels in the wrong direction, change the value on Use the traveling cable and the adaptation plugs supplied with the
SMLCD menu and try again, according to the following rule: plug kit as a cable extension.
Parameters → Drive settings → Phase Dir: See the installation diagram.
- to 1 if the present value is 0 Use the IMOF adapter tool to operate the machine with the ESE
- to 0 if the present value is 1 control panel connected to HK in the hoistway (Z 41322869).
- to 2 if the present value is 3
- to 3 if the present value is 2.
Execute a recall travel.
Record the value of phase direction parameter on the control label
(parameter change record).
Press the button JHM.
Check if the elevator stops.
Switch off JH, SIL and SIS.
Installation Travel with ESE Control Panel Installation Travel with ESE Control Panel K 40700039_12 26
Copyright © 2016 INVENTIO AG
7 Installation Travel with REC Panel
7.1 Prerequisites
Print Versions CANIC and CANICK Switch off JH, SIL and SIS, see the installation wiring diagram.
Two similar print versions CANIC and CANICK are used. CANICK If S.PEBO: Check that the connector BATT is unplugged.
is used in Korea. OKR.CANIC(K): Check that the following connectors are
If instructions are identical for both print versions: This document unplugged:
uses the expression "CANIC(K)".
Connector Description
POWC Power supply car
HK Traveling cable
SI Hoistway information
SISK Hoistway information
DOOR Door drive
2DOOR Door drive
XCOP Car operating panel
GNT Car operating panel
LNC Car operating panel
ACS Car operating panel
JNFF Car operating panel
LC Car lighting
MVEC Car fan
SOA Alarm horn on car
If PCBA CANGIO: Check if the configuration switches are set Set the switch JREC to NORMAL.
correctly. CANIC(K): Plug in the traveling cable connector HK.
The node ID switch is set to a unique number in the elevator. AS.ASIXB: Remove the jumper plugs on the following connectors:
The switch BAUD is set according to the bus to which the PCB is PEBO_SK
connected: 125 kbits/s for the nodes on the car and 50 kbits/s on SKS
the landing bus. HK.
All boards: The switch TERM is set to OFF. If board at the end of
the landing bus: The switch TERM of this board is set to ON. AS.ASIXB: Insert the plugs of the following components:
Manual evacuation system
CANIC.HK: Check the electrical continuity between pins 1-5. Hoistway wiring
Release the switch JHC. Traveling cable.
Test the electrical continuity with the following settings:
AS.ASIXB: Insert the ASIX.PEBO plug.
JREC DREC-E DREC-U/ Electrical If the batteries of the manual evacuation system are loaded below
Present Not DREC-D Continuity minimum level:
Present The elevator will not start.
Normal x 1) x 1) x 1) Yes Wait until the batteries are charged to continue installation travel.
Pressed Yes Replace all temporary bridges by final connectors.
Released -
Released No
Inspection Pressed - x 1) Yes
Pressed Yes
- Not present
Released No
1) Independent of the status
AS.ASIXB: Plug in the following connectors: Wait until the boot sequence is completed and SMLCD shows:
HK
SKS
PEBO_SK. A M?
AS.X1: Plug in the connector POWC to the position X1-1-1. 0#01 1|| INS
Switch on JH, SIL and SIS.
Set the switch JREC to INSPECTION. JHC On 0 . 0 0m / s
Press the button JHC.
OKR: Check the voltage on the traveling cable connector POWC,
see the installation diagrams.
Switch off JH, SIL and SIS.
OKR.CANIC(K): Plug in the following connectors:
Connector Description
POWC Power supply
LC Car light
Installation Travel with REC Panel Installation Travel with REC Panel K 40700039_12 31
Copyright © 2016 INVENTIO AG
7 Installation Travel with REC Panel
7.3 Installation Travel with REC Panel
Installation Travel with REC Panel Installation Travel with REC Panel K 40700039_12 32
Copyright © 2016 INVENTIO AG
7 Installation Travel with REC Panel
7.4 Door Drive Connection and AutoSetup (V15/35 without landing door coupled)
Remove any mechanical stops of the door operation. Switch on JH, SIL and SIS.
OKR.CANIC(K): Plug in the following connectors: Wait until the boot sequence is completed and the SMLCD
DD V15/35: The entrance side switch is above the plug X1-CAN-T. displays:
Connector Description
DOOR DC supply and CAN bus for front door drive, check A M?
the entrance side switch:
1 Side 1 = front door
0#01 1|| 2|| INS
2DOOR DC supply and CAN bus for rear door drive, check Install 0 . 0 0m / s
the entrance side switch:
2 Side 2 = rear door
Installation Travel with REC Panel Door Drive Connection and AutoSetup (V15/35 without landing K 40700039_12 33
Copyright © 2016 INVENTIO AG
7 Installation Travel with REC Panel
7.4 Door Drive Connection and AutoSetup (V15/35 without landing door coupled)
Obstacle
(KET-S2)
Locked/
Opened
4 Key (DRET-O) (+)
Closed
Ready
5 LED INSP (inspection)
6 LED SETUP
7 LED Ready
8 LED Locked / Opened
9 LED Obstacle
ON / OFF Auto > 5s
Id. No. 5950643 10 LED Closed (KET-S2)
11 LED COM (CAN communication)
1 23 7 8 9 10 4
[33147; 04.08.2011]
Installation Travel with REC Panel Door Drive Connection and AutoSetup (V15/35 without landing K 40700039_12 34
Copyright © 2016 INVENTIO AG
7 Installation Travel with REC Panel
7.4 Door Drive Connection and AutoSetup (V15/35 without landing door coupled)
Check the following LED status: Fix the KTC contact arm on the door carrier with a tape (a) to keep
the lock hook in unlocked position.
Color Name Status Description
- The door can move automatically.
Green INSP ON -
Green Setup OFF - a
Green Ready ON -
Yellow Locked/Opened BLINKING SLOWLY -
Red Obstacle OFF -
Orange Closed (KET-S2) ON If panels closed
Green COM ON -
Shortly press the keys DRET-S (-) and DRET-O (+) to check the
door movement direction.
If the movement direction is correct:
Continue with chapter Door Drive Auto-Setup (V15/35 with landing
door).
If the movement direction is not correct:
Continue with the following steps.
Installation Travel with REC Panel Door Drive Connection and AutoSetup (V15/35 without landing K 40700039_12 35
Copyright © 2016 INVENTIO AG
7 Installation Travel with REC Panel
7.4 Door Drive Connection and AutoSetup (V15/35 without landing door coupled)
Installation Travel with REC Panel Door Drive Connection and AutoSetup (V15/35 without landing K 40700039_12 36
Copyright © 2016 INVENTIO AG
7 Installation Travel with REC Panel
7.5 Door Drive AutoSetup (V15/35 with landing door)
During AutoSetup, all car door safety devices are enabled. The Lock the car door.
activation of a safety device interrupts the setup procedure. Press the key DRET-S (-) until the LED Locked/Opened is ON.
If AutoSetup fails: Close the landing doors manually.
Check if an obstacle was triggering a safety device. Disable inspection door: Press the key INSP
If yes: HMI: Press Setup for > 5 s to restart AutoSetup. - The LED INSP is OFF.
If no: Check the mechanical door settings. Inspection control station: Press the button DREC-U or DREC-D
Set the switch JREC to INSPECTION CAR. until the car is at floor level.
If JHT: Switch on JHT. Enable inspection door: Press the key INSP
If JHCT: Switch on JHCT. - The LED INSP is ON.
Check the following LED status: Press the key Setup / AutoSetup for more than 5 seconds to start
AutoSetup.
Color Name Status Description LED SETUP is SLOW BLINKING: AutoSetup is in progress.
Green INSP ON - – The door opens a small distance.
– The door locks.
Green Setup OFF -
– The door opens and closes the first time with reference speed.
Green Ready ON - – The door opens and closes the second time with reduced
Yellow Locked / Opened BLINKING Auto-Setup normal speed.
SLOWLY pending – The door opens and closes the third time with final normal
OFF Auto-Setup OK speed.
If LED SETUP is OFF: AutoSetup is completed successfully.
Red Obstacle OFF -
If LEDs SETUP, Closed (KET-S2), Obstacle, Locked/Opened and
Orange Closed (KET-S2) ON If panels closed Ready are FAST BLINKING: AutoSetup failed.
Green COM ON - – To clear the error: Press the key Setup.
Installation Travel with REC Panel Door Drive AutoSetup (V15/35 with landing door) K 40700039_12 37
Copyright © 2016 INVENTIO AG
7 Installation Travel with REC Panel
7.5 Door Drive AutoSetup (V15/35 with landing door)
Check the door movement and performance: Check the car door to landing door alignment and the clutch
Check the movement while fully opening and closing 2–3 times. movement.
Check the stopping while opening at full speed. Press the key DRET-S (-) until the LED Locked/Opened is ON.
Check the stopping while closing at full speed. Press the key DRET-O (+) for < 0.2 seconds to open the clutch.
Check if the landing door panels and car door panels are moving.
Key Description - If no door movement is visible: The car doors and the landing
DRET-O (+) Opens doors, stops closing movement doors are aligned correctly.
Repeat the check 2–3 times.
DRET-S (-) Closes doors, stops opening movement
Define the door opening and closing speed.
Define the door open position: Press the key DRET-S (-) until the LED Locked/Opened is ON.
Press the key DRET-O (+) to fully open the door. Press the key Setup to setup the speed.
Press the key Setup to set the OpenPosition. Use the keys DRET-S (-) and DRET-O (+) to select the closing and
- The LED SETUP is ON. the opening speed value.
Use the keys DRET-S (-) and DRET-O (+) to position the door - HMI: Values: 100 %, 80 %, 60 %, 40 %.
panels flush to the frame. Press the key Setup to store the defined opening and closing
- Every pressing of the keys moves the door panels by 1 mm in speed.
opening or closing direction. - The LED SETUP switches OFF.
Press the key Setup to store the actual door position.
- The LED SETUP is OFF. If no action is performed on the HMI for 30 seconds, the actual
door position is not stored and the LED Setup will go off.
If no action is performed on the HMI for 30 seconds, the actual
Disable inspection door. HMI: Press INSP key.
door position is not stored and the LED Setup will go off.
- The LED “INSP” is OFF.
REC: Set the switch REC to NORMAL.
AS: Switch off JH, SIL and SIS.
Installation Travel with REC Panel Door Drive AutoSetup (V15/35 with landing door) K 40700039_12 38
Copyright © 2016 INVENTIO AG
7 Installation Travel with REC Panel
7.6 Special Setting for Heavy Doors
Installation Travel with REC Panel Special Setting for Heavy Doors K 40700039_12 39
Copyright © 2016 INVENTIO AG
7 Installation Travel with REC Panel
7.7 Special Setting for Landing Doors with Different Weight
If the weight of the landing doors is not same on all floors, follow the Setting for a floor with normal door weights:
steps below: - Follow the steps defined in section “7.5 Door Drive AutoSetup
– There are only two different door masses supported by a single (V35 with landing door)”
DO VAR 35. - Travel to the top floor
– Assure that nobody is inside the car before starting the - Set the switch JREC to NORMAL.
commissioning (safety barrier). Setting for a floor with heavy weight landing doors.
Activate the setting for different landing doors: - Set special trip KFM:
- Set the switch JREC to INSPECTION CAR. Login → Commands → Special Trips → KFM → KFM State = ON
- Switch on JH, SIL and SIS. → OK.
- Login → Parameters → VD35Param → VD35 Param ID = 25 → - Move the car to a floor with heavy landing doors:
VD35. Param = 0 → OK. Login → Commands → Car Call → Floor 1 →
Define the “Floor Map Table” for landing doors: Normal/Heavy OK Entry Side = 1 or 2 → OK.
- Login → Parameters → Door → LanDoorWeight. - Set the switch JRH to INSPECTION:
For each floor level set door weight: - Login → Test → VD35 Tests → VD35 Param ID = 2 → OK.
- Floor = 1 → OK → Normal Door/Heavy Door. The AutoSetup for the heavy door is now in progress. Wait until
the result “Success” or “Failed” is shown.
For each second entrance: Define the “Floor Map Table” for landing
- Set the switch JRH to NORMAL.
doors Normal/Heavy:
- Disable special trip KFM:
- Login → Parameters → 2 Door → DoorWeight.
Login → Commands → Special Trips → KFM → KFM State = OFF
Repeat the above two steps for every floor. → OK.
Installation Travel with REC Panel Special Setting for Landing Doors with Different Weight K 40700039_12 40
Copyright © 2016 INVENTIO AG
8 Manual Evacuation
8.1 PEBO - Pulsed Electric Brake Opening
The manual evacuation is performed by BCM 2002/03 and AS.BCM: Check the following LED Status:
supplied by the Short Interruption Power Supply (SIPS) device. Color Name Status Description
It is used for the manual evacuation of a trapped passenger in
Green WDG1 Blinking Normal Operation (only BCM 2002)
case of power failure.
The supply device is powered by two batteries, whose capacity Green WDG2 Blinking Normal Operation (only BCM 2002)
depends on the requirements of the hoisting machine brake Red OVLT OFF Normal status.
and the maximum distance between the floors of the building. AC input voltage ≤ 264 V.
Preconditions Red ERR OFF Normal status
No NGL supply Yellow EM OFF JEM switch deactivated.
LUET signal is inactive Manual evacuation is blocked, brake
Two battery packs are installed. opening by control enabled.
Procedure
Configure the function KMEBATOK on the input 2 (pin 4) of
ASIXB PCBA.
- Procedure described on the chapter "Configuration of
ASIXB I/Os".
SMLCD: Access the KMEBATOK:
Login → Status → Board I/O → LOCAL → KMEBATOK.
ASIXB: With I/O connector plugged, check if the input status is
active (1a).
AS: Switch off JH.
Plug the battery units inside the SIPS box.
Switch on JH.
Wait until the boot sequence is completed and the SMLCD displays
the elevator status. Negative feedback is given in case the load
The traction media monitoring setup starts automatically after the During the setup procedure, you are prompted to enter the
measuring travel and the boot sequence have been completed. manufacturing date of the traction media.
– The SMLCD displays "TMMB", if the system misses the The manufacturing date is printed on the back side of the traction media
parameters for the traction media monitoring. as follows:
– The SMLCD displays "SCAN IO" in the fourth line, if the connectors
BIOBUS and HK are not connected.
A M? 1 2 3
Procedure
Wait until the boot sequence is completed and the SMLCD
displays:
- "TMMB", if the system misses the parameters for the traction
media monitoring.
- "SCAN IO" in the fourth line, if the connectors BIOBUS and HK are
not connected.
SMLCD: Check that the control date is correct: Confirm with OK.
Status → Date & Time. - The SMLCD displays the first STM.
If not correct: Correct the control date:
Parameter → System → Date. Belt Number
SMLCD: Activate the parameter configuration of the traction media
monitoring: =1
Login → Commands → TracMediaMon → ConfigChangeEna →
OK.
The parameter configuration of the traction media monitoring is
terminated automatically 1 minute after activation.
Edit the TM manufacturing date and confirm with OK. If different from present control clock date: Enter the installation
- The SMLCD returns to the STM number screen. date of the traction media. The installation date is valid for all
traction media.
The number of STMs is a chip card parameter.
Confirm with OK.
If the indicated number of STMs does not match with the
- The display shows:
number of the STMs on site: Request the correct chipcard
according to the installation.
Change the STM number to the next STM and insert the STM
A DIS M?
manufacturing date. 0#01 BESC
1--
Repeat the process for all STMs in the system.
IniPara BO O T
The SMLCD displays the present control clock date.
STMInstallDate
If the display shows: "BESC": Proceed with section "Brake
10.06.23 Component Operation Limit Setup". The system misses the
parameters for the brake emergency stop monitoring.
YY mm dd
Operational Limit of Brake Pads Collect the brakes production serial numbers of the machine.
The function within CO MX SW counts the number of emergency stops The brake ID numbers are entered in the control during the setup
to provide a warning if the brake pad is close to the end of its operational procedure.
limit. - The brake production serial numbers are composed by 6 digits
If the limit number of emergency stops is reached: CO MX SW (numbers or letters).
issues a warning via telemonitoring. - The brakes ID numbers to be entered through SMLCD consist of
If the shut down number is reached: CO MX SW issues a the last four digits of the brake production serial numbers, as
controlled blocking of the elevator. follows:
The setup of the brake component operation limit initializes the function Wagner: 0799128-001-BM07 → ID no.: 9128
within CO MX SW.
The numbers “-001-BM07” are linked to the
production date
A DIS M? Kendrion: P17552/136 → ID no.: 7552
0#01 1-- BESC The numbers “/136” are linked to the
production date.
IniPara BO O T Leroy I2HL0941-002 → ID no.: 0941
Somer:
ConfigChangeEna
Success
A DIS M?
0#01 1 2 N
NORMAL 0.0 0m/ s
Procedure
Floor-depending zero load calibration: To compensate the
effects of the guide rail alignment on the detection of small loads, Switch on JH, SIL and SIS.
an automatic calibration procedure is required. It must be Move the car to the floor where the calibration weights are located.
performed after the completion of the guide rail adjustment. Check that the car is empty.
Preconditions SMLCD: Open the car:
The sensor is fixed according to the J 41384063 Digisens KL-66 Login → Command → Door → Side 1 or 2 → Open → OK.
Installation Instruction CAPK33. Before commissioning the tape Switch on JRH to keep the door open during calibration.
shall be removed and the screw tightened with recommended: Status: LM Load and Freq.
1.28 Nm - Check that Freq 1 and Freq 2 are within 14.000 Hz ... 18.000 Hz.
SMLCD: Acquire the zero load reference point:
Commands → LM Commiss CLC → Zero Load Cal → OK.
- The control reads the load sensor output and associates it with the
empty car.
Wait until the SMLCD displays "Success".
Place the calibration weight in the car (25–100 % of GQ).
SMLCD: Initiate the known load reference point:
Commands → LM Commiss CLC → Ref Load Cal.
1 - The SMLCD displays the entry screen for the known load value.
[40700039_006; 19.12.2014] Set a new reference load value.
1 Adhesive tape Press OK.
The counterweight has been loaded as required - The control reads the load sensor output and associates it with the
Completion of the guide rail adjustment new load value.
The sliding or roller guides shoes are properly adjusted within the
correct tolerances and they are according to the layout drawing
and installation method.
Preconditions
The car is empty.
Procedure
Switch on JH, SIL and SIS.
Move the car upwards and downwards to check the ride quality.
If strong vibrations: Investigate and eliminate the source of the
vibrations before adjusting the leveling accuracy. 1
Prepare a table on paper to record the leveling accuracy on all
floors.
Measure the leveling accuracy on each landing and record the
values in the table. [40700039_005; 01.08.2014]
SMLCD: Enter the floor level adjustment table: 1 Car magnet reader position
Login → Commands → Adj. Floor Lev → OK. Select the floor subject to the leveling accuracy adjustment using
If the level accuracy corrections are more than 5 mm in any floor, the up or down keys.
follow the next steps: Press OK.
- Readjust the car magnet reader position (1) and check the right "+" means that the car must stop at a higher position.
position according to the type of door defined in EMBD K Adjust the value in mm.
43402040.
Press OK.
- Activate again the Teach-in mode and restart the measuring
travel, as defined in chapter "AC GSI (SALSIS) Connection". Repeat the last three steps for floors that require adjustment.
- Restart the procedure defined in chapter "Floor Level Press ESC and UP simultaneously to exit the floor level adjustment.
Adjustment". Measure the leveling accuracy again.
If necessary: Repeat the corrections.
SMLCD: Perform a drive end commission operation:
Login → Commands → Drv End Commiss → OK.
The values resulting from the acquiring process of the car unbalance at
From the control SW version 10.07.00 and newer, the values of
top and bottom can be inspected with the SMLCD:
the car unbalance on the top and bottom are acquired during the
measurement travel. Parameters → Unbalance → Unbalance top and Unbalance
bottom
The acquiring of values of the car unbalance on top and bottom can be - Top → Unbalance bottom = +7 [kg]
initiated from SMLCD: - Bottom → Unbalance top = +9 [kg].
SMLCD: Set special trip KFM. Not allow landing calls:
Login → Commands → Special Trips → KFM → ON → OK
SMLCD: Initiate the acquisition of car unbalance on top and bottom
Command → Special Trips → LearnCarUnbalance → OK
The elevator travel to the top floor and bottom floor to acquire the
unbalance values
Wait until "LearnCarUnbalance" → "Done".
The values on top and bottom as showed (example):
– Bottom = 7 [kg]
– Top = 9 [kg].
Store changes. End commissioning on SMLCD:
Commands → Drv End Commiss → OK
SMLCD: Disable special trip KFM
Command → Special Trips → KFM → OFF → OK
Final Drive Adjustment Car Unbalance for Drive Torque Adjustment K 40700039_12 57
Copyright © 2016 INVENTIO AG
12 Configuration of ASIXB I/Os
12.1 Configuration of ASIXB I/Os
Only to be performed if there are ASIXB I/Os to be configured. Scroll down the list until the PCBA type to be programmed appears
and press OK.
Activate the "Service Visit" to disable the monitoring of critical I/Os
SMLCD: Login → Commands → Service Visit → ON → OK
- A blinking "*" on the SMLCD and an acoustic signal indicate the
LOCAL 1/1
"Service Visit" mode.
Activate the I/O configuration process.
BOARD
SMLCD: Login → Commands → Program I/O function
- A scrolling list of all PCBA types with configurable I/Os appears.
- The ASIXB PCBA is identified by the word "LOCAL".
[37438; 29.10.2010]
Pro gram I/O Func
A list of the available I/Os of the selected PCBA is shown, indicating
>LO CAL their present status.
CO P P 0 1 N o t a s s i g n e d
BL IN P 0 2 N o t a s s i g n e d
[37437; 29.10.2010]
P 0 3 N o t a s s i g n e d
P 0 4 N o t a s s i g n e d
[37439; 29.10.2010]
Scroll down the list until the I/O to be programmed appears and Press OK.
press OK.
Using the up and down arrows, change the I/O function and press BMK program
OK.
- The selected value is shown = RNO
- The order is alphabetic by I/O function acronym.
OK?
BMK IO list
= Not assigned [37442; 29.10.2010]
[37441; 29.10.2010]
If COP display shows "Er" during the commissioning process: Exit COP (Side 1, Position 1)
and re-enter the commissioning process again.
Switch off JH, SIL and SIS.
OKR.CANIC(K):
Plug in the connectors XCOP, ACS, JNFF, LNC and GNT.
COP: If COP2 available:
Connect the cable from COP2 to the XCOP2 connector.
COP2: If COP3 available:
Connect the cable from COP3 to the XCOP2 connector.
COP3: If COP4 available:
Connect the cable from COP4 to the XCOP2 connector.
[40700039_001; 02.05.2014]
PCBAs of COPs: CANCP for FI GS COP and CANCPI for third
party COP.
COP2 (Side 2, Position 1)
For COP, COP2, COP3, COP4 on CANCP PCBA or on CANCPI
PCBA inside OKR (if present):
Check the setting of the DIP switches:
Access Side DIP1 DIP2 DIP3 DIP4
COP Side 1: Position 1 ON OFF OFF OFF
COP2 Side 2: Position 1 ON OFF ON OFF
COP3 Side 1: Position 2 ON ON OFF OFF
COP4 Side 2: Position 2 ON ON ON OFF
[40700039_002; 02.05.2014]
CANCP PCBA For FI GS COP (CANCP PCBA) or for third party COP (CANCPI
PCBA), check the following LEDs status:
Color Name Status Description
Green DC supply ON +24 V
Red CAN_ERR OFF CAN bus error
Green CAN_RUN Blinking CAN bus activity
Check each COP shows the current car position on its position
indicator.
If JHM not pressed: The SMLCD displays the error message
[40700039_003; 02.05.2014]
"Teach-in COP failed not enabled" when attempting a COP
Switch JHM to Stop. teach-in.
Switch on JH, SIL and SIS.
- A buzzer sounds.
- All COPs: Bus communication is established.
If capacitive COP buttons are installed, continue with the checking It is possible that the side to teach-in does not correspond to the
of the COP configurable inputs and outputs. main access side selected by DIP3.
If FI GL COP or third party COP interface CANCPI is installed, skip If there is a car call button that corresponds to the indicated floor:
to "Verification of the COP configurable inputs and outputs". Press the call button.
SMLCD: Start the COP button configuration: Press the button DT-O.
Login → Commands → Teach-in COP. - The COP beeps and shows "AC" on the display.
Select the COP for the teach-in: If there is no car call button corresponding to the indicated floor on
Commands → Teach-in COP → Entry Side: Side 1/2 → COP. the COP: Press the button DT-O.
Position: Position 1/2 → ON/OFF Press the button DT-O.
Select the main entry side, associated with the DIP3 of the COP - The COP beeps and shows the next floor number available for this
board: access side.
- Side 1 = OFF Repeat the last three steps until the topmost floor on this access
- Side 2 = ON side is configured.
Select the position of the COP, associated with the DIP2 of the - The position indicator shows "CP".
COP board: If there are car calls for the opposite access side:
- Position 1 = OFF Press the buttons DT-O or 2.DT-O.
- Position 2 = ON
Repeat the previous three steps for the opposite access side, until
Select the option ON to start the teach-in process. the position display shows "CP".
- The selected COP beeps and shows CP on its position indicator.
Exit the COP button configuration mode:
COP: Press the door open button DT-O or 2.DT-O that corresponds Commands → Teach-in COP → COP Teach-in → Select COP →
to the side to be taught-in. OFF → OK.
- The position indicator shows the lowest floor available on this - The SMLCD shows "Success".
access side.
Checking of the COP configurable inputs and outputs Check the configuration of the configurable inputs and outputs.
Check the configuration of the COP configurable inputs and If a COP I/O has to be configured: SMLCD:
outputs: Login → Commands → Program_IOfUNCT → COP.
- FI GL COP has four configurable inputs. - SMLCD displays the taught in COPs.
- FI GS COP and third party COP interface CANCPI have six
configurable lamps and six configurable inputs
These are supplied with a label that shows the function of each C O P 1/1
configurable I/O.
Start the I/O configuration in the SMLCD. If the COP I/Os
B o ardId:11
configuration is required, perform as follows: B o ardId:12
Login → Commands → Program_IOFunct → COP.
SMLCD: Store the configuration on the fixture PCBA: B o ardId:21
Login → Commands → Freeze Node Tr. → OK.
Press OK to confirm.
- The system stores the function.
- The SMLCD displays:
During the teach-in, only once car call per trip is accepted Press the button until the acknowledge lamps of all buttons and the
If the elevator is not from access on the floor where the call is arrows of the LIP (if present) light up for approximately 3 seconds.
made, the first call will result in the elevator arriving to the floor If LOP with 2 buttons: Press the floor call up button.
but not opening the door. To open the rear door and teach the – The COP does a long beep.
LOP on rear access side, a new car call to the same floor has – If SLCUX interface: The COP beeps two more times.
to be made. – Enter the car to enter a car call to the next floor.
– If selective control: Access the car on the side where the fixture
Enter the car. to be taught-in is installed.
Enter a car call to the floor where the fixture to be taught-in is
Repeat the procedure until all fixtures are taught-in.
installed (start with the bottom floor).
Travel to the floor closest to the controller cabinet.
The car travels to the bottom floor.
Exit the teach-in mode:
The door opens and remains open.
Login → Commands → Teach-in → OFF → OK.
If car with 2 selectively operated doors:
Enter a car call to the floor.
Access the car on the side where the fixture to be taught-in is
installed.
If car with 2 parallel operated doors:
Enter a car call to the floor.
- The front door opens.
Teach-in the front door fixtures.
Enter another car call to the same floor.
- The front door closes and the rear door opens.
Teach-in the rear door fixtures.
Exit the car within 12 seconds after the doors have fully opened.
The teach-in of the LIP nodes is performed in the machine room Within 12 seconds after the doors have fully opened, press and
or near the MRL cabinet. The nodes are connected one by one to hold the button connected to the LIP, until the LIP acknowledges
the bus using a “LIP teach-in cable” (ID no. 59710736), which is the teach-in by switching its arrows on.
available as an option. The cable connects the LIP to the Mark on the LIP the corresponding floor taught-in.
ASIXB.LOP plug. Unplug the LIP from the bus and button and connect the next one.
Repeat the procedure until all fixtures are taught-in.
Procedure Exit the teach-in mode:
Disconnect the ASIXB.LOP plug. Login → Commands → Teach-in → OFF → OK.
Release all floor access restrictions before starting the teach-in. Install the LIP on each floor, connecting it to the landing bus.
PCBA GCIOCF: Carry out a single reset. Return to the control cabinet and reconnect ASIB.LOP plug
- Once the scan process is complete, the scan process disappears Perform a single reset.
from the SMLCD. Wait until the SMLCD scanning messages are erased.
SMLCD: Activate the teach-in process: SMLCD: Store the configuration on the fixture PCBA:
Login → Commands → Teach-in LOP → ON → OK Login → Commands → Freeze Node Tr. → OK.
- The doors are open and remain open. The position of the car is SMLCD: Check the storing status on the topmost right corner, see
indicated on the SMLCD symbols in section “12.2 Commissioning of BIO2 Landing Bus
- If LIPs are present on the system: LIPs indicate "Out of Service". Fixtures”.
Connect a button to the LIP.DE-U plug and the LIP node to ASIXB Travel to all floors:
using the cables of the LIP teach-in kit. Check if the position indicators operate correctly
SLMCD: Perform a car call to the floor where the LIP has to be Direction arrows are only verified further when the elevator is
taught-in: connected in a group and floor calls can be entered.
Login → Commands → Car Call → Floor → OK.
- The car travel to the floor and open its doors.
An elevator shall have floor call buttons to have its node teached- Elevator A → JH OFF.
in. Some elevators share the floor calls, for such arrangement, the Elevator B → JH ON.
buttons are connected to one of the elevators, depending on the - If the main switch cannot be disconnected, unplug ASIXB.LOP
state of the power supply to the transfer relay embedded on the plug on elevator A and plug ASIXB.LOP plug on elevator B.
FI GS LOP (see schema S 274906 page 3) or on the third party Perform the teach-in process as described in section
interface transfer switch PCBA (BS1.Q, see S 274906 page 8). “12.2 Commissioning of BIO2 Landing Bus Fixtures” for elevator B.
The overall principle to teach-in landing node of those elevators is: Check that the “elevator B” is serving landing calls.
Switch “elevator A” power ON and “elevator B” power OFF. Elevator A → JH ON or plug ASIXB.LOP plug on “elevator A”.
Perform teach-in for all LOPs or LIPs of “elevator A”.
Switch “elevator A” power OFF and “elevator B” power ON.
Perform teach-in for all LOPs or LIPs of “elevator B”.
Identify which elevator has its nodes connected on DE1 plug of
LOPBG PCBA (FI GS) or A_XDE_D/U plug on BS 1.Q PCBA (third
party fixtures).
- This elevator is “elevator A”
- The other elevator to share the calls is “elevator B”.
Elevator A → JH ON.
Elevator B → JH OFF.
- If the main switch cannot be disconnected, unplug ASIXB.LOP
plug on elevator B.
Perform the teach-in process as described in section
“12.2 Commissioning of BIO2 Landing Bus Fixtures” for elevator A.
Check that the “elevator A” is serving landing calls.
Elevator I/Os Additional Procedure for Elevator with Shared Floor Calls K 40700039_12 72
Copyright © 2016 INVENTIO AG
14 Elevator I/Os
14.5 Additional Settings for BIO2 I/O Interface
BIO2 Devices with Configurable I/Os In case of CFG1 = OFF and CFG2 = OFF, the Teach-in LOP is
LIP required:
LOP - Login → Command → Teach-in LOP → ON → OK (JTI ON)
SLCUX PCBA - Send the elevator on floor down (if BIOGIO is mounted in the
BIOGIO PCBA. shaft)
- Press the “TEACH-IN” button and hold > 5 seconds
If PCBA BIOGIO: - Login → Command → Teach-in LOP → OFF → OK (JTI OFF)
- Check if the configuration switches are set correctly - Perform a double reset.
- Power on BIOGIO. BIOGIO is visible in program I/O function.
SMLCD: Activate the I/O configuration process.
Possible combinations are: Login → Commands → Program IO function.
PCBA CFG1 CFG2 Remarks - A list of all PCBA types with configurable I/Os appears:
BIOGIOx OFF OFF Teach-in required
BIOGIO1 ON OFF Pro gramIOFunc
BIOGIO2 OFF ON Fixed address >LO CAL
BIOGIO3 ON ON
CO P
SMLCD: Activate "Service Visit" to disable the monitoring of critical
I/Os: BL IN
Login → Commands → Service Visit → ON → OK.
- A blinking "*" on the SMLCD and an acoustic signal indicate that
the elevator is in "Service Visit" mode.
Press OK.
- The selected I/O is displayed associated with the chosen BMK. Program I/O list
Confirm with OK.
Success
BMK program
JAB
Press OK to confirm.
- The system stores the function on the PCBA.
[40700039_007; 10.04.2015]
Preconditions
The device is installed and wired as described on the commission
schematics.
At least one interface CANGIO is installed on the OKR and
connected to the CAN bus.
Check operation of the terminals according to the commissioning
procedure for the control after all terminals have been
commissioned.
Procedure
SMLCD: Perform car calls.
- The device is activated and clamps to the guide rails when the trip
is completed.
- The device is deactivated before the trip starts.
SMLCD: Check the correct turning of ICDD IO:
Login → Status → Board I/Os → CANGIO → <select boards> →
<select IO>.
Completion Work Simplex Installation Connection and Testing of Further Components K 40700039_12 82
Copyright © 2016 INVENTIO AG
16 Group Control
16.1 Procedure
Two possible group bus architectures are available in the CO MX Switch on JH, SIL and SIS.
control: SMLCD: Wait until the boot sequence is completed.
If duplex elevators: An Ethernet cable runs directly between the - The SMLCD displays the elevator status.
GCIOCF PCBAs of both elevators. - If elevator control recognizes another elevator for the first time:
If groups of more than two elevators or if gateway to LobbyVision A reset occurs.
in duplex installation: The cables run from each elevator processor
Travel to all floors.
PCBA or gateway to a hub, usually located on the first elevator
cabinet. Check that:
All floor calls are acknowledged and answered.
The position indicators and direction arrows operate correctly.
Switch off JH, SIL and SIS. Group functions are carried out (if present).
AS.GCIOCF: Switch off JH, SIL and SIS.
Check that the ETHERNET connectors are plugged in. - The elevator group is ready for acceptance tests SAIS.
Group Architecture Connector Color
Duplex Blue
Triplex Green
More than three elevators Green
If triplex:
L1.AS: Check that the Ethernet cables of all elevators to be
grouped are connected to the Ethernet switch.
Check that the switch Ethernet is powered.
Commissioning steps of telealarm system AC TMA1 AS. Check the following connections:
(ETMA PSTN) - Traveling cable XTT to ETMA-MR-PSTN.X1-1-1
The COP lamps LAGC and LARC will blink while the ETMA is - ETMA-MR-PSTN.COM to GSMI.ETMA
still not configured. - ETMA-MR-PSTN to the Phone line.
SMLCD: Check the unconfigured state of the installation, restoring
Preconditions
if necessary.
The RMCC database contains an entry for the elevator to be Login → Parameters EmbeddedTM → ModemType = No Modem
commissioned. Parameter → EmbeddedTM → ServitelID = 0000000000
The elevator is identified by the third to twelfth character of the Parameter → EmbeddedTM → ModuleNumber = 00.
commission number. The number is included in the legend of Perform a single reset.
commission schematics.
Wait until the SMLCD scanning messages are erased.
SMLCD: Start ETM modem detection.
Login → Commads → ETMDetectModem
- If successful, SMLCD shows "Success" and ETMA will perform
the initial configuration call.
COP. Check connection inside COP: ETMA-CAR.X1-1-6 to - If unsuccessful, configure the parameters manually following the
CANCP.XTELA next steps.
COP-OKR. Check the following Connections: Contact call center to know the Servitel ID and Shaft ID linked to
- ETMA-CAR.X1-1-1 to CANIC.GNT the elevator been commissioned. Servitel ID has a relationship to
- ETMA-CAR.X1-1-2 to XTT the phone number of the installation.
- XTT to Traveling cable.
SMLCD: Enter the installation Servitel ID
If triphonie present: Login → Parameters → EmbeddedTM → Servitel ID
- Check from each device of the devices and one of the
In case of multiple elevators connected to the same phone line:
ETMA-CAR-TRI plugs.
SMLCD: Check and modify the Shaft ID, if required
Login → Parameters → EmbeddedTM → Shaft ID
SMLCD: Check the Phone Prefix as follows: SMLCD: Disable the Alarm filtering
Login → Parameters → EmbeddedTM → PhonePrefix Login → Parameters → Car → Alarm Filter → Disable → OK
- It shall be empty in case the elevator have a direct phone line - This step allows an alarm call to be initiated with the elevator at
- It shall contain the prefix to dial an outside line if the elevator is the floor with door open, otherwise will be filtered by the control.
connected to a PABX line. Press the COP DA button more than 3 seconds.
SMLCD: Enter the alarm phones numbers 1 ... 4 - ETMA-CAR will emit a beep and dial PhoneNoAlarm1 as a first
Login → Parameters → EmbeddedTA → PhoneNoAlarm1 attempt.
Repeat for the 4 numbers: PhoneNoAlarm1, PhoneNoAlarm2, etc.) - Call Center operator will open the speaker and talk to the
SMLCD: Enter the phone number for notification calls, used to technician.
notify defects (for example, a permanent active DA button) Check with the call center operator if the commissioning number
Login → Parameters → EmbeddedTA → PhoneNoMonitor reported by the ETMA corresponds to the one of the elevator been
commissioned and correct it if necessary.
The line test call is mandatory for the configuration process.
SMLCD: Enable the Alarm filtering, when commissioning number
SMLCD: Enter the phone number for the line test calls. be verified.
Login → Parameters → EmbeddedTA → PhoneNoLineTst. Login → Parameters → Car → Alarm Filter → Enable → OK
- ETMA will automatically perform a line test call to the number
SMLCD: Final check of the ETMA parameters
entered in PhoneNoLineTst
- Login → Parameters → EmbeddedTM → Servitel ID
- If the line test is successful, ETMA got the acknowledge from the
(It is different from "0000000000")
call center and the LAMPS on the COP will be:
- Login → Parameters → EmbeddedTM → Module ID
Name Status Description (It is different from "00" (normally 10))
LAGC OFF Lamp Alarm Memory Car - Login → Parameters → EmbeddedTM → Shaft ID
(It is different from the ones on the other elevators that share the
LARC Blinking Lamp Alarm Acknowledgement Car same phone line).
Auto configuration:
Commissioning steps of the Embedded Telemonitoring (ETM),
when: Correct operation of embedded telemonitoring requires setting of
parameters which is automatically performed during the ETM auto
It is combined with telealarm function with AC TM2 (TAM2)
configuration process. Refer to the document J 41323447
It is not combined with telealarm function - rescue call done by
(configuration of components used in TA and TM functions).
an intercom system.
Procedure:
When telemonitoring is combined with AC TMA1 (ETMA PSTN), the AS: Prevent the traveling of the elevator.
device commission on the previous chapter "ETMA Tele-Alarm" also - Press the button JHM in ESE control panel.
covers the telemonitoring part.
If AS.CLSD present: Check the rotary switch position
There are two ways to connect the controller to RMCC for - If CLSD PCBA is directly connected to the phone line: Position "0".
telemonitoring when AC TMA1 is not present: - If CLSD PCBA is connected to Schindler PABX: Position "F".
Through a public switch telephone network (PSTN) using the
If AS.GSMI present: Check if PCBA is correctly installed and
PCBA called CLSD in the control cabinet
electrically connected to ASIXB PCBA.
Through a wireless GSM connection, using a communication
gateway (CGW) and an interface PCBA (GSMI) in the control Connection:
cabinet. If PSTN:
Preconditions: – Connect the phone of the PABX line to the CLSD.PSTN
If Schindler PABX: A connection to the external phone line exists. plug
The RMCC database contains an entry for the elevator to be – Connect the traveling cable plug XTT to the
commissioned. CLSD.ALARM plug.
The elevator is identified by the third to twelfth character of the If GSM:
commission number. The number is included in the legend of – Connect CGW to the GSMI PCBA with the RS 232 cable
commission schematics. – Connect the traveling cable plug XTT to the CGW.FXS
If telemonitoring is via GSM, CGW is installed and plug.
pre-commissioned according to EJ 604795 and powered.
If CGW present, check the followings LEDs status: Check the status "Communication" and "Configuration"
- SMLCD: Status → Embedded TM → Communication
Color Status Description
- Wait for the status "RMCC connected"
Green ON Power is present and CGW is - SMLCD: Status → Embedded TM → Configuration
connected to Schindler. - Wait for the status "Configured"
Blue ON or BLINKING GSM connection is present.
Communication Configuration Result
every 2 seconds
"RMCC "Configured" Configuration is successful.
SMLCD: Check the unconfigured state of the installation, restore if connected" A test trip will be performed.
necessary. "RMCC "Not configured" Configuration failed.
Login → Parameters → EmbeddedTM → ModemType = connected" The installation data might
No Modem not be present in the RMCC
Parameter → EmbeddedTM → ServitelID = 0000000000 database.
Parameter → EmbeddedTM → ModuleNumber = 00
Perform a single reset. The ETM test trip is a trip to a nearest possible floor, in up or down
Wait until the SMLCD scanning messages are erased. direction, but taken into account the shaft extremes and
SMLCD: Start ETM modem detection. potentially blocked floors.
Login → Commads → ETMDetectModem If configuration failed: Check the RMCC phone number.
- If successful SMLCD shows "Success" and ETMA will perform the SMLCD: Parameter → Embedded TM → TelNrRMCC.
initial configuration call Correct the RMCC phone number if necessary.
- If unsuccessful, repeat the ETM modem detection. – If phone number is changed: Initial configuration is performed
within seconds.
SMLCD: Perform a car call.
- The ETM considers the elevator in normal operation if a complete
trip including door opening is performed.
SMLCD: Check the status: SMLCD: Final check of the ETMA parameters
Status → Embedded TM → MonitLiftx, x for elevator number.
Login → Parameters → EmbeddedTM → Servitel ID
(It is different from "0000000000")
If telealarm device AC TM2 (TAM2) is present:
Login → Parameters → EmbeddedTM → Module ID
SMLCD: Disable the Alarm filtering (It is different from "00" (normally 10))
Login → Parameters → Car → Alarm Filter → Disable → OK Login → Parameters → EmbeddedTM → Shaft ID
– This step allows an alarm call to be initiated with the (It is different from the ones on the other elevators that share
elevator at the floor with door open, otherwise will be filtered the same phone line).
by the control.
Press the COP DA button more than 3 seconds.
– TAM2 will dial PhoneNoAlaram1 as a first attempt.
– Call Center operator will open the speaker and talk to the
technician.
Check with the call center operator if the commissioning number
reported by the ETMA corresponds to the one of the elevator
been commissioned. Correct it if necessary.
SMLCD: Enable the Alarm filtering, when commissioning
number be verified.
– Login → Parameters → Car → Alarm Filter → Enable
→ OK
LED Signalizations
SK
SMLCD
CHIP CARD T1 T2 T3 T4 T5 T6 LED Status Description
DUEISK-A CCS Blinking Chip card being read by the control
Lit There is a valid chip card in the chip card slot
CCS
LIFT ID BATT
0
1
2 3
4
5
COM Not lit No or not valid chip card in the chip card slot
CANL LR-U NGL
T1-T6 Lit Safety circuit voltage present at this point
1 0 CANS LUET LTRT
JMOF BIO LR-D LUEISK Not lit Safety circuit voltage absent at this point
IMOF Lit Installation travel active
CANL Blinking Elevator CAN bus active
CANS Blinking Landing CAN bus active
BIO Blinking Landing BIO bus active
LR-U Lit Car is traveling up
LUET Lit Car is at door zone
LR-D Lit Car is traveling down
ESC UP DOWN OK BATT Not lit Emergency supply battery OK
Lit Emergency supply battery not OK
NGL Lit Elevator DC power supply present
Buttons Not lit Elevator DC power supply not present
Button Description LTRT Lit Car speed is below door overbridging limit speed
DUEISK-A Safety circuit protection reset button LUEISK Lit Safety circuit protection active
JMOF Installation travel mode switch Not lit Safety circuit protection not active
Pos. Description
1 2 3 4 5 5 Status node tree:
6 7 8 9 10
Blinking "%" Node SW download in progress
A 10% *M! 12 "?" Node tree freeze required
11
0=01 1 2 N 13 Blinking "?" Executing node tree freeze
14 Blinking "!" Freeze not successful
NORMAL 0.00m/s
"!" Missing or new nodes found after freeze
W! 25635 Blank Freeze done and no changes on node tree
Display on SMLCD showing Elevator Status 6 Status drive:
0 Drive is at standstill
Pos. Description + Drive is accelerating
1 Elevator designation within group = Drive is traveling at constant speed
2 LMS status: - Drive is decelerating
CAL = LMS requires calibration F Drive not available
CALF = LMS requires floor dependant zero load calibration ? Unknown drive status
UNV = LMS is unavailable
7 Status car:
DIS = LMS is disabled
xx% = Car load in % of rated load = Car is at standstill within the door zone
3 Status service visit (blinking "*" when service visit is active, # Car is at standstill outside the door zone
blank if not) ↑ Car is traveling up
4 Status master ("M" = this elevator is group master, blank if not) ↓ Car is traveling down
? Unknown car status
8 Current group selector value (1 to n)
Zugerstrasse 13
6030 Ebikon, Switzerland
Phone +41 41 445 32 32
Fax +41 41 445 39 33
[email protected]
www.schindler.com