Professional Documents
Culture Documents
AR15 Parts Assembly
AR15 Parts Assembly
This guide is is created to help put together an AR-15 lower receiver from a stripped receiver
and a lower receiver parts kit.
Tools
There are a few tools that make it easier to put together these kits, but none of them are
necessary. Minimum requirements include a hammer and punch to drive in a couple of roll pins,
a flat-blade screwdriver for A2 stock screw, and either a screwdriver or Allen key for the pistol
grip screw. Specialized tools are available from Brownells, at 515-623-4000.
Roll Pin Punches - to drive roll pins (3/32", 1/8", 5/32"); these have a small raised
projection in the face of the punch to automatically center the punch and prevent the roll
pin from collapsing
Roll Pin Holders - used to hold and start roll pins... very convenient
Hammer - used to drive the roll pins
#10 Flat-Blade Screwdriver - used for A2 stock screw and some pistol grips
Block of wood - base to support receiver when driving roll pins
Pivot Pin Installation Tool - handy tool if you build a few lowers
Allen Key - used for some pistol grips
Telescoping Stock Wrench - to tighten telescoping stock lock ring
The Parts
The lower receiver parts kit consists of 30 parts not counting the stock assembly, the receiver,
or the pistol grip. It is a good idea to lay all your parts out on a flat, light-colored surface so that
you can verify all your parts are there, and find them easily when you need them.
Most parts kits come covered in oil to prevent rust; wipe all the excess oil off before assembly.
Because of tight tolerances, some of these parts will be a tight fit. With the exception of the roll
pins, no part should need to be hammered into place.
SPRINGS
Bolt Catch Spring - easily confused with the disconnector spring; disconnector spring
is tapered though.
Buffer Retainer Spring - second largest spring in the kit.
Disconnector Spring - similar to bolt-catch spring, but identifiable because one end is
wide than the other.
Hammer Spring - larger of the two similar springs.
Magazine Catch Spring - this is the largest spring in the kit.
Pivot Detent Spring - same as the takedown detent spring, so there are two in a kit.
Selector Spring - similar to the takedown and pivot detent springs, but there will only
be one of these.
Takedown Detent Spring - same as the pivot detent spring, so there are two in a kit.
Trigger Spring - the smaller of the two similar springs.
PINS
Assembly
The steps for assembly are presented in a sequence which has been effective. It is by no
means the only correct method, as it does not make any difference on the end result if the
magazine catch is installed before or after the bolt catch for instance. It is important to install the
selector before the pistol grip, and a few other steps that must be performed before others.
Unless you are experienced, follow the sequence presented and you will be successful.
Always work in a well-lit area, and it is helpful to work on a flat, hard surface. There are many
small pins and springs, and they have a tendency to roll or fly away and disappear forever... In
addition, look over the lower receiver before you begin the assembly. Many of the small holes
can have debris in them from the forging process; a small drill bit, turned by hand, will clean
these out nicely.
CAUTION:
IT IS POSSIBLE TO SCRATCH THE RECEIVER ON THIS STEP!
Take special care when turning the magazine catch to avoid rubbing against the hump
around the bolt catch.
FUNCTION CHECK
Check that depressing the magazine release button will push the magazine catch out of
the magazine well in the lower receiver.
Spring will return magazine catch to engage in magazine well.
Attach front of trigger guard assembly to the receiver using the detent.
Lay receiver on a block of wood, and drive roll pin into receiver and rear of trigger guard
using drive pin punch.
Make sure that the small block of wood is supporting the bottom flange and that the
trigger guard is in position supporting the top flange otherwise you risk bending or
breaking off one of the flanges.
Also watch as you put in the roll pin that it is going through the hole in the trigger guard
correctly.
FUNCTION CHECK
Check that by depressing the detent on trigger guard you are able to pivot the trigger
guard open.
BOLT CATCH ASSEMBLY
PARTS: bolt catch, bolt catch buffer, bolt catch spring, roll pin
TOOLS: 3/32" roll pin punch, 5/32" (or larger) punch
CAUTION:
IT IS VERY EASY TO SCRATCH THE RECEIVER ON THIS STEP!
Take special care to make sure pin in in place before driving it, and ensure that it is held
securely in place when striking the punch. Fiberglass packing tape - 2 layers thick -
taped over the receiver just between the receiver and the punch can help avoid
scratching.
When installing the bolt catch, first drive the roll pin about halfway into the rear hump
from the rear of the receiver using roll pin holder. It can be very difficult to get this pin
started; you might want to try squeezing the roll pin on one end with pliers or the vise
before starting. If you don't have a roll pin holder, then try holding it in place with a pair
of needle nose pliers while you drive using a 5/32" punch.
Install spring in hole on left side of receiver.
Install bolt catch plunger on top of spring with round portion on top and small end into
receiver. Make sure it moves freely in its hole.
Install bolt catch in receiver; it only fits on one way.
Use a 3/32" punch to hold the assembly by placing it through the front hump.
The pin can be driven the rest of the way from the rear as the punch will be pushed out
and while holding the bolt catch in correct alignment. (function check as you do it to
make sure it's going in correctly)
Avoid marring/scratching lower by covering receiver with tape, cloth, or other material
while you do this.
FUNCTION CHECK
Verify that the bolt catch functions smoothly and is under tension from the spring.
PIVOT PIN ASSEMBLY
PARTS: pivot pin, pivot pin detent, pivot pin detent spring
TOOLS: pivot pin installation tool, 3/32" drive pin punch
This is perhaps the hardest part of the lower assembly, so if available, install the
installation tool.
Insert spring and detent into receiver.
Compress detent in recess using 3/32" punch and rotate tool.
Push out tool with pivot pin and rotate until detent is in groove of pivot pin.
FUNCTION CHECK
Verify that the pivot pin detent prevents the pivot pin from coming off the receiver.
Note: If you do not have an installation tool, it can be difficult to get the pivot pin inserted
without losing the detent and/or detent spring; if these parts do fly out, they can be very
hard to find. The idea is to insert the spring and detent, and then compress them as you
insert the pivot pin. A pair of needle-nose pliers can be helpful. It is difficult to remove
the pivot pin once installed, so make sure you do it right the first time and make sure
you've cleaned out the detent/spring hole with a drill bit before inserting the spring.
TRIGGER ASSEMBLY
PARTS: Trigger, Trigger Pin, Trigger Spring, Disconnector, Disconnector Spring
TOOLS: 5/32" drive pin punch
Shoulder trigger spring onto trigger with ends of spring forward and under.
Install disconnector spring with the wider portion of spring down towards trigger and
push until it locks in there.
Position disconnector on top of trigger, where trigger pin will hold both in place.
Insert trigger assembly into receiver.
Insert trigger retaining pin through receiver, trigger, and disconnector. The trigger pin
has 2 grooves in it; one in the middle of the pin and one off to one side. It does not
matter which way it is inserted, though common practice is to insert from left to right,
with the groove to the left.
Insert hammer pin from opposite side to help align things as you push the trigger pin in
and the hammer pin out. You will have to push down on trigger assembly to align the
holes and get the pin in all the way.
FUNCTION CHECK
HAMMER ASSEMBLY
PARTS: hammer (with J-pin installed), hammer spring, hammer retaining pin
TOOLS: 5/32" drive pin punch
Install spring onto hammer, ends of spring to rear and shoulder on back of hammer.
Install hammer in receiver with feet pointing rearward away from hammer
Use 5/32" punch to retain hammer in place as you insert hammer retaining pin.
Like the trigger pin, you may have to push down and align the holes perfectly in order to
push the pin in all the way.
Ends of the hammer spring will rest on top of the trigger pin, with one end in the groove
on the trigger pin.
Inserting the hammer pin may require some effort, as the J-pin in the hammer will catch
the grooves in the pin.
FUNCTION CHECK
Verify that hammer locks to the rear when pushed back.
Verify that hammer pivots forward when trigger is pressed.
Without releasing the trigger, push the hammer back again and verify that it locks
(caught by disconnector).
Releasing the trigger should not cause the hammer to pivot fully forward (caught by
trigger).
Hammer will fall when trigger is pressed.
SELECTOR ASSEMBLY
With hammer cocked back, insert from left side of receiver, selector pointing up in the
'fire' position.
FUNCTION CHECK
PARTS: selector detent, selector detent spring, pistol grip, pistol grip screw, lock washer
TOOLS: Allen key or flat-blade screwdriver (depends on your screw type)
Install detent, pointed end towards the selector, and the spring into the receiver from the
bottom.
Carefully compress the spring with the grip and make sure spring fits into hole in grip.
Check the function of the selector with the grip held in place; if too tight (unable to
rotate) you may need to either cut the spring, or clean out the hole in the grip.
Once feel is acceptable, secure the grip in place with the screw and lock washer.
FUNCTION CHECK
Verify selector is able to move from safe to fire and clicks in place. It should not move
past the 'safe' or 'fire' positions.
With selector on 'safe', verify cocked hammer is not released when trigger is pressed.
With selector on 'semi', verify hammer is released when trigger is pressed.
NOTE: Selector cannot be rotated to 'safe' unless hammer is cocked.
A2 STOCK
PARTS: takedown pin, takedown pin spring, takedown pin detent, stock, buffer extension,
retainer, retainer spring, buffer, buffer spring
TOOLS: #10 (or larger) flat-blade screwdriver
PARTS: takedown pin, takedown pin spring, takedown pin detent, telescoping stock, buffer
extension, backplate, locking ring, retainer, retainer spring, buffer spring, buffer
TOOLS: Telescoping Stock Wrench