04-SAMSS-005 2018 Check Valves - Flanged, Lug, and Butt-Welding
04-SAMSS-005 2018 Check Valves - Flanged, Lug, and Butt-Welding
Contents
I Scope.............................................................. 2
II Conflicts and Deviations................................. 2
III References..................................................... 2
IV General........................................................... 3
V Modifications to API STD 594......................... 4
Appendix A.............................................. 6
Appendix B.......................................…... 7
Appendix C........................................….. 8
Appendix D........................................….. 9
I Scope
This specification, together with the Purchase Order, covers the minimum requirements
for steel, nickel-base alloys, and other alloys in ASME B16.34 (Table 1), check valves
in accordance with API 594, Type A and Type B, for nominal pipe sizes (NPS) 2 and
greater for ASME Classes 150 through 2500:
Type ‘A’ single plate or dual plate check valves are short face-to-face: lug or
double-flanged.
Type ‘B’ bolted cover swing check valves are long face-to-face: flanged or butt-
welding ends.
Unless otherwise specified, Valves covered by this specification shall be suitable for
wet, sour liquid or gaseous hydrocarbon services with design temperature between
-18°C and 400°C.
Additional requirements for special services are covered in the following appendices:
Appendix A Low temperature service from -19°C to -45°C
Appendix B Cryogenic services from -46°C to -196°C
Appendix C Steam services
Appendix D Pipeline service from -18°C to 120°C
Any conflicts between this document and other applicable Mandatory Saudi Aramco
Engineering Requirements (MSAERs) shall be addressed to the EK&RD Coordinator.
Any deviation from the requirements herein shall follow internal company procedure
SAEP-302.
III References
In addition to the references cited in API STD 594, material or equipment supplied to
this specification shall also comply with the latest edition of the references listed below
unless otherwise noted:
Page 2 of 10
Document Responsibility: Valves Standards Committee 04-SAMSS-005
Issue Date: 16 December 2018
Next Planned Update: 16 December 2021 Check Valves: Flanged, Lug, and Butt-welding
NACE International
NACE MR0175 / Petroleum, Petrochemical, and Natural Gas
ISO 15156 Industries - Materials for Use in H2S-Containing
Environments in Oil and Gas Production
Page 3 of 10
Document Responsibility: Valves Standards Committee 04-SAMSS-005
Issue Date: 16 December 2018
Next Planned Update: 16 December 2021 Check Valves: Flanged, Lug, and Butt-welding
7. Other than standard materials (Refer to Saudi Aramco Engineering Standards for
other permitted materials)
V Modifications to API STD 594, Check Valves - Flanged, Lug, Wafer and
Butt-welding Ends
The following paragraph numbers refer to API STD 594, Eight Edition, July 2017,
which is part of this specification. The text in each paragraph below is an addition,
exception, modification, or deletion to API STD 594 as noted. Paragraph numbers not
appearing in API STD 594 are new paragraphs to be inserted in numerical order.
5 Design
5.1.18 (Addition) Type ‘A’ valves: The body shall be of a “retainerless” type
design, i.e., there shall be no threaded plugs in the pressure boundary.
5.1.19 (Addition) Type ‘A’ & Type ‘B’ valves: Refer to 04-SAMSS-035 for end
connections NPS 26 and above.
5.1.20 (Addition) Type ‘B’ valves: The area of the flow passage shall be at least
equal to the seat port area. The inside diameter of the seat opening shall not
be less than that specified in Appendix A of ASME B16.34 for the specified
size and pressure class. For sizes and pressure class combinations where the
dimension is not specified in Appendix A of ASME B16.34, the inside
diameter shall be as agreed to between purchaser and manufacturer.
5.3.1 (Addition) Type ‘A’ (single plate) & Type ‘B’ valves: The body seat ring
shall be inclined or the hinge shall have an offset.
6 Materials
Page 4 of 10
Document Responsibility: Valves Standards Committee 04-SAMSS-005
Issue Date: 16 December 2018
Next Planned Update: 16 December 2021 Check Valves: Flanged, Lug, and Butt-welding
8 Marking
9 Shipping
Page 5 of 10
Document Responsibility: Valves Standards Committee 04-SAMSS-005
Issue Date: 16 December 2018
Next Planned Update: 16 December 2021 Check Valves: Flanged, Lug, and Butt-welding
Revision Summary
17 April 2016 Major revision to reaffirm the requirements to meet company needs and to align
this materials system specification with the international standard API STD 594
latest edition.
16 December 2018 Major Revision to adopt the 8th edition of API 594 and reaffirm the requirements.
Page 6 of 10
Document Responsibility: Valves Standards Committee 04-SAMSS-005
Issue Date: 16 December 2018
Next Planned Update: 16 December 2021 Check Valves: Flanged, Lug, and Butt-welding
Additional requirements for valves for low temperature service from -19°C to -45°C:
1) The requirement to meet NACE MR0175/ISO 15156 is not mandatory for valves
supplied to this appendix unless otherwise specified.
Page 7 of 10
Document Responsibility: Valves Standards Committee 04-SAMSS-005
Issue Date: 16 December 2018
Next Planned Update: 16 December 2021 Check Valves: Flanged, Lug, and Butt-welding
Additional requirements for valves for cryogenic service from -46°C to -196°C:
1) Valves supplied under this appendix are not required to meet NACE MR0175/ISO
15156.
2) Valves shall be made entirely of stainless steel AISI Type 304 or AISI Type 316.
Page 8 of 10
Document Responsibility: Valves Standards Committee 04-SAMSS-005
Issue Date: 16 December 2018
Next Planned Update: 16 December 2021 Check Valves: Flanged, Lug, and Butt-welding
1) Valves supplied under this appendix are not required to meet NACE MR0175/ISO
15156.
2) Type ‘B’ valves - Pressure seal type body-to-cover joints are acceptable and shall
meet the requirements of MSS SP-144, Style A or B.
3) Type ‘B’ valves: Integral or welded seats are required. For valves Class 600 and
higher, the body seating area (or seat ring) and disc seating surfaces shall be hard-
faced with Stellite No. 6 or 21.
Page 9 of 10
Document Responsibility: Valves Standards Committee 04-SAMSS-005
Issue Date: 16 December 2018
Next Planned Update: 16 December 2021 Check Valves: Flanged, Lug, and Butt-welding
Appendix D (Type ‘B’ valves only) - Pipeline service from -18°C to 120°C
1) Valves shall be suitable for wet, sour liquid or gaseous hydrocarbon services
between -18°C and 120°C.
2) Valves shall meet the requirements of API SPEC 6D and may be either
metal-to-metal or soft seated.
3) Valves shall be full opening type and shall allow for the passage of a pipeline
scraper.
Page 10 of 10