Professional Documents
Culture Documents
Lab Equipment
Lab Equipment
Web-Circular
To,
The Principals
All institutes affiliated to MSBTE
Sub : Standard list of Machinery & Equipment required for different diploma programs
AICTE Approved and M. S. Approved Courses
Sir / Madam,
MSBTE has recently revised the curriculae of all the AICTE approved as well as the
State approved Diploma programs & has also converted these programs in to semester pattern. It was
under consideration of MSBTE to prepare a detailed list of Standard Machinery & Equipment required
for performing laboratory experiments of each subject of a particular diploma program. Project
institutes were identified for this work & the task was carried within a span of one month.
The list includes essential as well as desired machinery & equipment for a particular
course. It is expected that every institute running a particular program/ course possesses every
machinery & equipment mentioned in the list.
It may so happen that the names of various machinery & equipment are repeated in two
different lists. A judicious decision will have to be taken whether it is necessary to procure different
machinery for different purposes. It is therefore appealed to all the institutes to go through the entire
list and give suggestions in this regard.
Your suggestions are most welcome latest by 10th June 2007, so that corrections if any
can be made & final list will be published by for 15th June 2007.
Secretary
MSBTE, Mumbai
Copy forwarded To
1. Hon. Director, Directorate of Technical Education, M.S. Mumbai for information
2. Hon. Director, MSBTE, Mumbai
3. The Joint Director, R.O. Mumbai/ Pune/ Nashik/ Aurangabad/ Amravati/ Nagpur
4. The Dy. Secretary, R.O. MSBTE, Pune/ Nagpur/ Aurangabad & OIC, Mumbai Subregion
APPENDIX- A
(2006-07)
AUTOMOBILE ENGINEERING
SAME AS
MECHANICAL LAB
NAME : POWER
ENGINEERING
ANNEXURE - I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERY ( Essential equipment/ Hand Tools)
(Required for conducting thePractical)
1. Name of course/ Department:- Auto. Engg. Dept.
2.Name of laboratory :Auto Pneumatics & Hyd.
SAME AS
MECHANICAL LAB
NAME : Industrial
Fluid Power
ANNEXURE-I I
APPLIED MECHANICS
(CIVIL ENGINEERING)
(AM)
(AICTE Approved Course)
1 of 32
INDEX
Sr No. Essential Equipments Labwise Page No
1 Engineering Mechanics Lab 1
2 Mechanics of Structures Lab 4
3 Concrete Technology Lab 5
4 Geotechnical Engineering Lab 8
2 of 32
ANNEXURE I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Essential Equipment/Hand Tools)
(Required For Conducting The Practicals)
4 of 32
9 Differential pulley block. A cast iron double sheave pulley 3
block having 16 no. of cogs on
bigger pulley and 8 no. of cogs on
smaller pulley mounted on sturdy
cast iron bracket and moving
freely on two steel free bearings.
A snatch pulley of 10 cm dia with
hook at bottom shall be supplied
along with a continuous steel
chain, along with a hook for
effort..
10 Geared pulley block Consists of a metallic (preferably 3
steel) cogged wheel of about 20
cm dia with endless chain and a
gear toothed wheel of 15 cm dia
mounted on the same axis. This
toothed wheel shall mesh with
another toothed wheel of same
dia along with a protruded load
drum of 10 cm dia to which a rope
can be attached so as to suspend
the weights of 10 kg, 20 kg-2
weights and a 50 kg weighs. The
slotted weights of 1 kg-2 weights,
2 kg-2 weights, 5 kg-2 weights
and 10 kg weight along with a
hook for effort.
11 Single purchase crab Fitted with heavy cast iron wall 3
brackets and attachable to
protable M.S.framed trolley. The
effort wheel is of C.I.material of 25
cm diameter with a hole for effort
attachment mounted on a shaft of
about 40mm dia. On the same
shaft a geared wheel (machine
cut) of 15 cm dia shall be
mounted. The teeth of this pinion
wheel shall mesh with another
(spur) toothed wheel of 30 cm
diameter. This spur wheel shall be
mounted on another axle to which
a load drum of about 7.5 cm
diameter of heavy C.I. material
shall be attached to which the
heavy loads can be attached at
bottom. A set of 5 slotted weights
of 2 kg each and a hanger of 2
kg..
12 Double purchase crab. Having assembly same as above 3
(Sr.No.11) but with double set of
gearing arrangement. A set of 5-
slotted weights of 5 kg each and
hanger of 5 kg.
5 of 32
13 Worm and worm wheel Consisting of machine cut worm 3
nickelled steel gear of 25 cm
diameter carrying a metal drum
protruding 5 cm of 12.5 cm
diameter above which a machine
cut worm on steel spindle carrying
a 12.5 cm dia pulley. The whole
arrangement shall be fixable on
heavy cast iron brackets capable
to be fixed to a wall or a m.s.
framed trolley complete with effort
pulley, string and/hooks, with 5
weights of 1 kg each and a
hanger of 1 kg..
Notes : 1 : Equipment/apparatus
recommended for labouratory
preferably be procured digital and
electronic based display with or
without analog display provision.
4 Each apparatus/equipment
along with their accessories must
be with ISI mark (wherever
applicable).
7 of 32
ANNEXURE I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Essential Equipment/Hand Tools)
(Required For Conducting The Practicals)
4 Each apparatus/equipment
along with their accessories must
be with ISI mark (wherever
applicable).
9 of 32
ANNEXURE I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Essential Equipment/Hand Tools)
(Required for Conducting The Practicals)
10 of 32
8 Compression Testing Machines It is fully automated version of 1
the manual testing machine.
Capacity 3000 KN, provision for
automatically burning pump on or
off controlling set pace rate
switching the machine off under
predetermined conditions, data
acquisition, storage, management
and analysis are fully automated.
The system is compatible with
any computer with following
specification : P IV and above, 1.9
GHz, 256 MD RAM, Intel
Chipset with on board graphic
card, 40 GB HDD, 1.44 MD FDD,
CD ROM drive, printer HP 5550
or latest. UPS APC 500 VA or
equivalent, 1 serial port, 1 parallel
port, support for data transmission
over distance of several KM.
Useful for testing in field. Facility
to save test data along with other
information on as age, sample no.
batch name etc. powerful analysis
and reporting software tools.
11 of 32
10 Curing Tank ACW. For 72 cubes of 150 mm / 70.6 1
mm size. 24 hour cycle from time
of mixing, controlled 35oC or
100oC +- 2oC curing temp,
controlled 27 o +- 2oC curing temp
for grey cement. Accelerated
curing for worm water method.
Temp range 55 +- 2oC.
15 Los Angeles abrasion testing machine with Ref. Std. IS:10070, Rotation of 1
Abrasive charge Ref.Std. IS:2386(Part 4) drum :30-33 rpm, Operation on
415 V, 3 Phase, 50 Hz, AC
supply. Abrasive charge set of 12
hardened steel balls of 48 mm dia.
28 PH meter Digital. 1
29 Trays Enamel tray size 650 x 500 x 50
mm, 600x450x50mm,
450x300x40 mm,
300x250x40mm, 200x150x30
mm. 5 each
30 Thermometer Thermometer, glass, range 0oC to
+ 360oC. 2
31 Miscellaneous Needle vibrator. 1
32 Accessories Meter scale, Weights, Pans, LS
Trays, Scoops, Peppete, Solid
glass rods, trowels etc.
Notes : 1 : Equipment/apparatus
recommended for laboratory
preferably be procured digital and
electronic based display with or
without analogue display
provision.
2 : Computer laboratory equipped
with 10 PCs, 1 server, 1 UPS, 1
LCD, 1 OHP projection system be
provided for Applied Mechanics
Deptt.
13 of 32
3 : While calling quotations for
procurement of Lab. equipment,
suppliers shall be asked to submit
copy of IS of manufacturing
specifications and IS of test
conductance (where applicable)
of supplied equipment for
performance/verifying purpose.
4 Each apparatus/equipment
along with their accessories must
be with ISI mark (wherever
applicable).
14 of 32
ANNEXURE I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Essential Equipment/Hand Tools)
(Required For Conducting The Practicals)
10 Set of stand pipes Glass stand pipes for falling head 3 I.S. 2720
(variable head) test arrangement, (Part 4)
varying in diameter from 5 to 20 1986
mm, mounted on stand or
otherwise fixed on wall preferably
6mm dia., 10mm dia. And 20mm.
Dia. 15 of 32
11 Sieve Shaker Carries up to 7 sieves of 15 cm. 2 I.S. 2720
To 20 cm. Diameter. The shaker (Part IV)
is driver by 1/4 HP. Motor 1985
through a reduction gear. The
sieve table does not rotate but is
inclined from the vertical axis and
the direction of inclination
changes progressively on
clockwise direction. By removal
of stop pin fixed below the table,
the shaker can have a rotary
motion. In addition to gyratory
motion of the table, there is an
upward and downward movement
ensuring that each square of cm.
of the sieve is utilised. The gear
mechanism runs in an oil bath.
13 Mixing Pan 1
14 Graduated Cylinder 1
15 Meter Scale 1
16 Stop watch 3
17 75 micron wire gauge. 1
18 Thermometer 2
19 Source of de-aired water 1
20 Direct Shear stress apparatus with electronic Should have facility to determine 1 I.S.2720
instrumentation system. the residual shear strength and a (Part 13) -
choice of 12 rates of strain. The 1986.
apparatus is designed for testing a
square specimen of 60mm x
60mm x 25mm.
21 Direct Shear stress apparatus. Shear box grid plates, porous 1 I.S.2720
stones, base plates and loading (Part 13) -
pad and water jacket shall confirm 1986.
to I.S. 11229-1995. Preferably
with electronic instrumentation
system. As in Sr.No. 20 above.
16 of 32
24 Micrometer dial gauges Accurate to 0.01 mm, one suitably 2 I.S.2720
mounted to measure horizontal (Part 13) -
movement and other suitably 1986.
mounted to measure vertical
compression of specimen.
17 of 32
38 Steel Rammer With soild mild steel foot 140 mm 1 IS. 2720
dia. And 75 mm height with a (Part 29)
concentrically screwed 25 mm 1975
dia. Solid mild steel staff. The (Reaffirm
overall length of the rammer ed 1988)
including the foot as well as the
staff should be approximately 900
mm. Should weigh approximately
9 Kg.
39 Balance Accurate to 1 g., Cap. 10 Kg. 1
40 Palette knife A convenient size is one having a 1
blade approx. 200 mm long and
30mm wide.
41 Grafting tool or spage or pick axe straight edge A steel strip about 30 cm. Long, 1
2.5 cm wide and 3 to 5 mm thick,
with one bevelled edge will be
suitable
42 Balances One of capacity 10 kg. Sensitive 2
to 1 g. and other of capacity 200g.
Sensitive to 0.01 g.
51 Laboratory C.B.R. apparatus with Load frame Capacity 50 KN, with high and 1 IS 2720
motorised low rates of travel of 1.25, 1.5 & (Part 16)
2.5 mm/min. Lead Screw. 1979.
52 Weights This shall confirm to 4.4 of IS 1 set
9669-1980.
18 of 32
53 Loading machine With a capacity of at least 5000 1 IS 2720
kg. And equipped with a movable (Part 16)
head or base that travel at a 1979.
uniform rate of 1.25 mm/min. for
use in forcing the penetration
plunger into the specimen. The
machine shall be equipped with a
load indicating device that can
read to an accuracy of one half
percent of loads.
19 of 32
64 Vane shear apparatus laboratory motorised Consists of a torque head 1 IS2720
adjustable in hieght by mean of a Part (30)
lead screw rotated by a drive
wheel to enaqble the vane to be
lowered in to the specimen.
Rotation of vane is by means of a
hand wheel which operates a
worm gear arrangement turning
the upper end of a calibrated
torsion spring. The vane shaft is
attached through teh hollow upper
shaft to a resettable pointer, which
indicates the angle of torque on a
dial graduated in degrees. The
dial reading multiplied by spring
factor gives the torque. A
container should also supplied
with set of springs one each
approx. 2 kg-cm, 4 kg-cm and 8
kg-cm in a wooden carrying case
preferably electrically operated,
rate of rotation is 1/16 RPM.
Suitable for operation on 230V,
50 Hz, Single phase, AC supply.
20 of 32
70 Triaxial cell For testing specimen size 38 mm 1 IS 2720
dia x 76 mm long, perspex (Part
chamber with anvil and loading 11,12)
plunger, suitable for use with the 1971
fluid selected for use at internal (Reaffirm
pressure up to 10 bar (10 ed 1978).
kg./cm2). Transperent chamber is
recommended. The base of the
cell shallb e provided with a
suitable central pedestal with
drainage outlets with valves. The
cell is fitted with four sleeve
packed valves of no volume
change type on the base.
21 of 32
78 Deformation dial gauge A dial guage with 0.01 mm 1 IS 2720
graduations and sepcific travel to (Part 10)
permit. 20% axial strain. 1973
79 Vernier calipers Suitable to measure physical 1 IS 2720
dimensions of the test specimen to (Part 10)
the nearest 0.1 mm. 1973
80 Sampel Extruder It consists of jack, lever frame or 1 IS 2720
other device for the purpose of (Part 7)
excluding conpacted specimen 1980
from mould. Reaffirme
d 1987,
second
edition.
81 ASTM Grooving tool Type B of IS 9259 5
82 Dial gauge 0.01 mm x 25 mm travel. 1
83 Sampling tube Unrelieved, 38 mm dia x 200 mm 6
long set of two.
84 Hand operated extractor For 38 mm dia for extracting soil 1
core specimens of 38 mm dia
from sampling tube or from larger
size samplers. Consists of sample
extractor frame, jarring link,
adaptor with locking, screw split
mould. 38 mm dia x 88 mm long,
provided with quick release
clamps.
85 Accessories Meter scale, Small Containers, LS
Weights, Pans, Trays, Scoops,
Evaporating dishes etc.
Notes : 1 : Equipment/apparatus
recommended for labouratory
preferably be procured digital and
electronic based display with or
without analog display provision.
4 Each apparatus/equipment
along with their accessories must
be with ISI mark (wherever
applicable).
22 of 32
ANNEXURE II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Desirable Equipment/Hand Tools)
(Optional Equipments)
1 Vehicle screw jack used for different four All metallic body accurately 3
wheelers machine cut screw with different
pitches so as to carry a tyre load
of vehicle 20 t, 10t and 4 t load
carrying capacity. Fitted on a
heavy cast iron base and complete
with appropriate lever arm.
23 of 32
(l)Chains short and long - 6 only,
(m) Boss brackets - 1 only, (n)
Ring brackets - 5 only, (o) Hook
brackets - 4 only, (p) Pulley
brackets - 3 only, (q) Member
balances to indicate tensile force -
3 only, (r) Member balances to
indicate compressive force - 3
only. All parts are
interchangeable so that the
different frame works can be
assembled with same
components
3 Apparatus for reaction of forces in beams. Consists of (1) two dial type 1
compression spring balances of
20 kg capacity with zero
adjustment device, (2) Two
triangular knife edge support
blocks of prismatic shape and
fitted on cast iron base. (3) A
wooden beam of about 1500 mm
length 60mm x 80mm in cross
section duly fitted with steel back
plate and holes at ends, (4) Set of
two conical weights of 1,2,5 & 10
kg with ring at top two cast
aluminium rectangular stirrups.
Notes : 1 : Equipment/apparatus
recommended for labouratory
preferably be procured digital and
electronic based display with or
without analog display provision.
4 Each apparatus/equipment
along with their accessories must
be with ISI mark (wherever
applicable).
24 of 32
ANNEXURE II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Desirable Equipment/Hand Tools)
(Optional Equipments)
25 of 32
Notes : 1 : Equipment/apparatus
recommended for labouratory
preferably be procured digital and
electronic based display with or
without analog display provision.
4 Each apparatus/equipment
along with their accessories must
be with ISI mark (wherever
applicable).
26 of 32
ANNEXURE II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Desirable Equipment/Hand Tools)
(Optional Requirements)
27 of 32
7 Portable ultrasonic non-destructive digital Range 0.1 to 9999 micro s, 2
indicating tester. feasibility up to environmental
temp 50oC, Output : Analog
pulse, Pulse width equal to
transmit time available from BNC
socket on rear panel. Operation of
250 V, 60 hrs.
8 Thermometer a) Digital thermometer, range 2
50oC to 280oC.
b) Non contact thermometer, 2
range - 20oC to 315oC (Infra-red).
28 of 32
Notes : 1 : Equipment/apparatus
recommended for labouratory
preferably be procured digital and
electronic based display with or
without analog display provision.
4 Each apparatus/equipment
along with their accessories must
be with ISI mark (wherever
applicable).
29 of 32
ANNEXURE II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Desirable Equipment/Hand Tools)
(Optional Equipments)
30 of 32
14 Loading platform truss. Of sufficient size and properly 1 IS 1888
designed members so as to 1982
estimate load reaction for (Reaffirme
d)
conducting load test. The set up
used for gravity loading.
15 Hydraulic jack Of required capacity with 1 IS 1888
properly calibrated load 1982
measuring device such as pressure (Reaffirme
d)
gauge, electronic load cell or
proving ring shall be used.
31 of 32
25 Guide pipe assembly Bore 73 mm OD approx. Shoe 1
hardened with an inside cutting
edge, tripot with pulley and built in
ladder. Drill rods, head fitted with
ball check valve and adapter.
Body split length wise.
Notes : 1 : Equipment/apparatus
recommended for labouratory
preferably be procured digital and
electronic based display with or
without analog display provision.
4 Each apparatus/equipment
along with their accessories must
be with ISI mark (wherever
applicable).
32 of 32
MAHARASHTRA STATE BOARD OF
TECHNICAL EDUCATION, MUMBAI
0
4 Temp range upto 250 C, Electrical Heater
Tray Dryer with regulator, Fan, Temperature indicator, 01 set
Digital weight indicator for measuring
weight of material on tray
5 Composite wall apparatus i Heater Assembly. 01 set
ii. Test specimen MS 2 Nos. Backelite 2
Nos. Wood 2Nos.
iii. Assembly Mounting frame.
iv. Clamp Plates 2 Nos.
v. Set of thermocouples.
Control Panel
i. Temperature 12 Channel Digital Indicator
0
Range : 0 - 300 C
ii. Dimmerstat 0 - 2 A.
iii. Main On/Off Switch.
iv. Voltmeter 0 - 250 V.
v. Ammeter 0 - 3 A.
6 Finned tube heat exchanger (For Air Liquid System) 01 set
i. Outer tube of I.D. 50 mm., Length 1 M.
ii. Inner tube of I.D. 15 mm., Length 1 M.
iii Longitudinal Fins for the max. heat transfer.
iv. Electrical Geysors of 2 Kw
v. Rotameter for hot water. Range : 0 - 10 LPM
vi. Rotameter for flow measurement of Air.
Control Panel :
i. 12 Channel Digital Temperature Indicator
o
Range : 0 - 300
ii. Set of Thermocouples
7 Shell & Tube Heat Exchanger For Water/Water Media 01 set
a. Shell & tube Heat Exchanger (1:2 pass)
Shell of M.S. having 250 mm. dia. Length
800 mm & thickness 5 mm
Tubes 25 mm O.D. ‘b’ class seamless pipes
, 32 mm triangular pitch
Cuts baftles are provided as per TEMA standards
b. Heating Arrangement :
i. Electrical Gyesors of 2 Kw for hot
water supply.
ii. Rotameter for flow measurement of hot
water. Range : 0 - 11 LPM
iii. Rotameter for flow measurement of cold water.
c. Control Panel :
i. 12 Channel Digital Temperature Indicator
o
Range : 0 - 600
ii. Set of Thermocouple, main switch
sockets etc. to be provided
8 Double Pipe Heat Exchanger i. Outer tube of I.D. 50 mm & length 1000 m01 set
ii. Inner tube of I.D. 25 mm & length 1000 mm
a. Heating Arrangement :
i. Electrical Gyesors of 2 Kw for hot
water supply.
ii. Rotameter for flow measurement of hot
water. Range : 0 - 11 LPM
iii. Rotameter for flow measurement of cold water.
b. Control Panel :
i. 12 Channel Digital Temperature Indicator
o
Range : 0 - 600
ii. Set of Thermocouple, main switch
sockets etc. to be provided
9 Emmissivity of Material a. Experimental Set up : 01 set
i. Test Plate : Polished Aluminum.
ii. Referance Plate : Black Aluminum.
iii. Mica-Insulated heaters for black & polished body.
iv. Set of Thermocouples.
b. Control Panel :
i. 12 Channel digital Temperature Indicator
0
Range : 0 - 300 C
ii. Dimmerstat 0 - 2 A.
iii. Main On/Off Switch.
iv. Voltmeter 0 - 250 V.
v. Ammeter 0 - 2 A.
vi. Ammeter Selector Switch.
10 Natural & Forced Convection For Natural Convection 01 set
Apparatus i. Stainless steel/Brass Vertical cylinder.
ii. Cylinder enclosure with stand.
iii. Set of Thermocouples.
iv. Heater - 500 W
v. Thermocouple
For Forced Convection
1
Water-CO2 Type Fire Extinguisher As per IS Code 01 no
Page 1
INDEX
Page 2
Annexure-I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Essential Equipment/Hand Tools)
(Required for Conducting The Practicals)
Minium
Remark if
Sr.No. Name of Equpt./Machinery Technical Specification Qty.Nos
any.
Required
P-IV 3.06 GHz,102-D
Motherboard, 512 MB RAM,
1 Personal Computer 20
80GB HDD, 15" TFT, 1000 MBPS
NIC
2 UPS System 5 KVA Online, 4 Hrs. Backup 2
SVGA 800x600 Lamp Life Span
3 LCD Projector 1
(2000-2500 Hrs)
4 Windows XP 2.0 Prof. Edition 20 User The Computers
5 Turbo C Std. Edition 20 User in this lab.
6 C++ Complete Version 20 User Must be
7 Visual C++ Prof. Edition 20 User connected
8 Java 2 Software Dev. Kit 1.4 Onwards 20 User using
9 MS Office Office XP 20 User Windows XP
10 Front Page 2000 Prof. Edition 20 User Network
environment
11 Visual Studio 6.00 Onwards 20 User
12 Ethernet Switch 24 Port 1
Online Protection with Firewall
13 Antivirus Software 20 User
securities
Laserjet 30 PPM 16 MB RAM
14 Printer
1200 DPI 1
15 Printer Line Printer 1
16 Scanner A4 Size 1
Page 3
Annexure-I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Essential Equipment/Hand Tools)
(Required for Conducting The Practicals)
Minium
Remark if
Sr.No. Name of Equpt./Machinery Technical Specification Qty.Nos
any.
Required
P-IV 3.06 GHz,102-D
Motherboard, 512 MB RAM,
1 PC TRAINER KIT FOR DEMO 1
80GB HDD, 15" TFT, 1000 MBPS
NIC
2 UPS System 5 KVA Online, 4 Hrs. Backup 2
SVGA 800x600 Lamp Life Span
3 LCD Projector 1
(2000-2500 Hrs)
4 P-IV Motherboard Intel 865/915 20
5 Hard Disk HDD 80 GB 20
6 Display Adaptor SVGA with Drivers 20
7 Modem 56 Kbps 1 For conducting
8 ATX Cabinet With SMPS ATX Type 20 the Practicals
9 Floppy Disk Drive 1.44 MB 20 of Subject
10 CD Writer 58 X 20 Computer
11 Keyboard 110 Keys 20 Architecture
12 Mouse 3D Optical Mouse 20 and
13 Monitor 15" CRT / TFT 20 Maintenance
14 Scanner A4 Size 2 and Basic
Laserjet 30 PPM 16 MB RAM Workshop
15 Printer 2 Practice
1200 DPI
16 Printer DMP 132 Column. 2
17 Diagnostic Softwares Nortan/QA Plus/PC Tools 20 User
18 Tool Kit Complete set 20 User
19 RS232C Cable 9 Pin/25 Pin 2
20 Logic Probe DP-21 Digital Logic Probe 1
21 Logic Pulser Frequency Rage 50 MHz. 1
22 Logic Analyser 18 Channel 500 MHz. 1
23 Digital Multimeter 3 and 1/5 Digit 1
24 Current Tracer Amprobe P-100 Probe for CT-100 1
25 CRO 20 MHz. Dual Channel 1
Page 4
Annexure-I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Essential Equipment/Hand Tools)
(Required for Conducting The Practicals)
Minium
Remark if
Sr.No. Name of Equpt./Machinery Technical Specification Qty.Nos
any.
Required
P-IV-Dual Core Tech. 102D
1 Windows NT Server with S/W Mother Board, 1 GB RAM, 160 1
HDD, 1000 MBPS NIC, 17" TFT
20 Clients
P-IV-Dual Core Tech. 102D must be
2 Windows 2003 Server with S/W Mother Board, 1 GB RAM, 160 1 connected to
HDD, 1000 MBPS NIC, 17" TFT all the Servers
as (5 Servers +
P-IV-Dual Core Tech. 102D 20 Clients) For
3 Unix Server with S/W Mother Board, 1 GB RAM, 160 1 conducting the
HDD, 1000 MBPS NIC, 17" TFT practicals of
subjects
Operating
P-IV-Dual Core Tech. 102D
System,
4 Windows 2000 Server with S/W Mother Board, 1 GB RAM, 160 1
Network
HDD, 1000 MBPS NIC, 17" TFT
Management
P-IV-Dual Core Tech. 102D and
Novel Netware Server 4.1 Onwards Administrator,
5 Mother Board, 1 GB RAM, 160 1
with Software Computer
HDD, 1000 MBPS NIC, 17" TFT
Network
P-IV 3.06 GHz,102-D
Client Machines with Windows NT,
Motherboard, 512 MB RAM,
6 Windowx XP, Windows 2000, 20
80GB HDD, 15" TFT, 1000 MBPS
Windows 98, Unix Client Software
NIC
7 UPS System 5 KVA Online, 4 Hrs. Backup 2
SVGA 800x600 Lamp Life Span
8 LCD Projector 1
(2000-2500 Hrs)
9 HUB 16 Port 2 For
Broadband/
10 Modem External Modem 56 KBPS 1
ISDN/PSTN
11 ISDN Router 5 Port 1 Internet
12 Ethernet Switch 24 Port 1 Connectivity
Laserjet 30 PPM 16 MB RAM
13 Printer
1200 DPI 1
14 Printer DMP 132 Column. 1
15 Scanner A4 Size 1
Page 5
16 MS Office Office XP 20 User
Online Protection with Firewall
17 Antivirus Software 20 User
securities
18 ORACLE 8.0 Onwards 20 User For DBMS,
19 SQL Server Prof. Edition 20 User RDBMS
20 Visual Basic/ Visual Studio 6.0 Onwards 20 User Practicals
With all Netwrok Tools (Clamping,
21 Network Toolkit 4
Network Tester etc.) For Netwok
RJ-45, 1000 MBPS NIC, UTP Installation
22 Other Network Accessories Cable, T-Connector, Optical -- Practicals
Fibre,Coax Cable 50 Ohm.etc.
Page 6
Annexure-I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Essential Equipment/Hand Tools)
(Required for Conducting The Practicals)
Minium
Remark if
Sr.No. Name of Equpt./Machinery Technical Specification Qty.Nos
any.
Required
P-IV-Dual Core Tech. 102D
1 Windows 2003 Server with S/W Mother Board, 1 GB RAM, 160 1
HDD, 1000 MBPS NIC, 17" TFT
Page 7
28 Test Management Tool Test Director 20 User
29 UML Prof. Edition 20 User
30 VB Dot Net Prof. Edition 20 User
All the
31 ASP Dot Net Prof. Edition 20 User
32 ORACLE 8.0 Onwards Prof. Edition 20 User
systems
Online Protection with Firewall must be
33 Antivirus Software 20 User connected
securities
Laserjet 30 PPM 16 MB RAM with Internet
34 Printer ISDN/PSTN/
1200 DPI 1
35 Printer DMP 132 Column. 1 Broad Band
36 Scanner A4 Size 1 Services.
Page 8
Annexure-I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Essential Equipment/Hand Tools)
(Required for Conducting The Practicals)
Page 9
Annexure-I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Essential Equipment/Hand Tools)
(Required for Conducting The Practicals)
Minium
Remark if
Sr.No. Name of Equpt./Machinery Technical Specification Qty.Nos
any.
Required
With inbuilt Power supply 5V,
12 V, Logic Switches 12 Nos.,
LED output 12 Nos., 7
Digital Trainer Kit/Component
1 Segment Display 2 Nos., Bread 10
Development System For
Board, Clock Generator 0.1
Conducting
Hz., 1 Hz, 10 Hz, 100 Hz, 1
the practicals
KHz.
of subject
2 Universal Shift Register Kit Demo. Kit 1
Digital
Dcade Counter Using IC 7490
3 Demo. Kit 1 Technics for
Kit
Second Year
4 3 Bit Synchronous counter Kit Demo. Kit 1
CO
5 A to D Converter Kit Demo. Kit 1
6 D to A Converter Kit Demo. Kit 1
7 CRO 20 MHz. Dual Channel 5
8 Logic Analyser 18 Channel 500 MHz. 1
Page 10
Annexure-I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Essential Equipment/Hand Tools)
(Required for Conducting The Practicals)
Minium
Remark if
Sr.No. Name of Equpt./Machinery Technical Specification Qty.Nos
any.
Required
P-IV 3.06 GHz,102-D
Motherboard, 512 MB RAM,
1 Personal Computer 20
80GB HDD, 15" TFT, 1000 MBPS
NIC
2 Windows XP Prof Edition 20 User
3 MS Office Office XP 20 User
4 MS DOS 7.00 Onwards 20 User
5 UPS System 5 KVA Online, 4 Hrs. Backup 2
SVGA 800x600 Lamp Life Span
6 LCD Projector 1
(2000-2500 Hrs)
Laserjet 30 PPM 16 MB RAM
7 Printer 2
1200 DPI
8 Printer DMP 132 Column. 2
9 Digital Multimeter 3 & 1/5 Digit 1
10 CRO Dual Channel 20 MHz. 1
11 8085 Microprocessor Kit 8085 with Power Supply 20
8086 MP. Kit with Inbuilt
12 8086 Microprocessor Kit 20
Assembler
13 8085 Assembler Software MASM 20 User
14 8086 Assembler Software MASM 20 User
15 80286 Assembler Software MASM 20 User
16 80386 Assembler Software MASM 20 User
17 80486 Assembler Software MASM 20 User
18 P-IV Assembler Software MASM 20 User
19 8051 Micro Controller Kit Complete Set. 20 User
20 8051 Cross Assembler Software With Editor 20 User
Page 11
Annexure-II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Desired Equipment/Hand Tools)
(Optimal Equipments)
Minium
Remark if
Sr.No. Name of Equpt./Machinery Technical Specification Qty.Nos
any.
Required
P-IV 3.06 GHz,102-D
Motherboard, 512 MB RAM,
1 Personal Computer 20
80GB HDD, 15" TFT, 1000 MBPS
NIC
2 UPS System 5 KVA Online, 4 Hrs. Backup 2
SVGA 800x600 Lamp Life Span
3 LCD Projector 1
(2000-2500 Hrs)
4 Windows XP 2.0 Prof. Edition 20 User The Computers
5 Turbo C Std. Edition 20 User in this lab.
6 C++ Complete Version 20 User Must be
7 Visual C++ Prof. Edition 20 User connected
8 Java 2 Software Dev. Kit 1.4 Onwards 20 User using
9 MS Office Office XP 20 User Windows XP
10 Front Page 2000 Prof. Edition 20 User Network
11 Visual Studio 6.00 Onwards 20 User environment
12 Ethernet Switch 24 Port 1
Online Protection with Firewall
13 Antivirus Software 20 User
securities
Laserjet 30 PPM 16 MB RAM
14 Printer 1
1200 DPI
15 Printer Line Printer 1
16 Scanner A4 Size 1
Page 12
Annexure-II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Desired Equipment/Hand Tools)
(Optimal Equipments)
Minium
Remark if
Sr.No. Name of Equpt./Machinery Technical Specification Qty.Nos
any.
Required
P-IV 3.06 GHz,102-D
Motherboard, 512 MB RAM,
1 PC TRAINER KIT FOR DEMO 1
80GB HDD, 15" TFT, 1000 MBPS
NIC
2 UPS System 5 KVA Online, 4 Hrs. Backup 2
SVGA 800x600 Lamp Life Span
3 LCD Projector 1
(2000-2500 Hrs)
4 P-IV Motherboard Intel 865/915 20
5 Hard Disk HDD 80 GB 20
6 Display Adaptor SVGA with Drivers 20
7 Modem 56 Kbps 1
For conducting
8 ATX Cabinet With SMPS ATX Type 20
the Practicals
9 Floppy Disk Drive 1.44 MB 20
of Subject
10 CD Writer 58 X 20
Computer
11 Keyboard 110 Keys 20
Architecture
12 Mouse 3D Optical Mouse 20
and
13 Monitor 15" CRT / TFT 20
Maintenance
14 Scanner A4 Size 2
and Basic
Laserjet 30 PPM 16 MB RAM Workshop
15 Printer 2
1200 DPI Practice
16 Printer DMP 132 Column. 2
17 Diagnostic Softwares Nortan/QA Plus/PC Tools 20 User
18 Tool Kit Complete set 20 User
19 RS232C Cable 9 Pin/25 Pin 2
20 Logic Probe DP-21 Digital Logic Probe 1
21 Logic Pulser Frequency Rage 50 MHz. 1
22 Logic Analyser 18 Channel 500 MHz. 1
23 Digital Multimeter 3 and 1/5 Digit 1
Amprobe P-100 Probe for
24
Current Tracer CT-100 1
25 CRO 20 MHz. Dual Channel 1
Page 13
Annexure-II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Desired Equipment/Hand Tools)
(Optimal Equipments)
Minium
Remark if
Sr.No. Name of Equpt./Machinery Technical Specification Qty.Nos
any.
Required
P-IV-Dual Core Tech. 102D
1 Windows NT Server with S/W Mother Board, 1 GB RAM, 160 1
HDD, 1000 MBPS NIC, 17" TFT
20 Clients
P-IV-Dual Core Tech. 102D must be
2 Windows 2003 Server with S/W Mother Board, 1 GB RAM, 160 1 connected to
HDD, 1000 MBPS NIC, 17" TFT all the Servers
as (5 Servers
P-IV-Dual Core Tech. 102D + 20 Clients)
3 Unix Server with S/W Mother Board, 1 GB RAM, 160 1 For conducting
HDD, 1000 MBPS NIC, 17" TFT the practicals
of subjects
P-IV-Dual Core Tech. 102D Operating
4 Windows 2000 Server with S/W Mother Board, 1 GB RAM, 160 1 System,
HDD, 1000 MBPS NIC, 17" TFT Network
Management
P-IV-Dual Core Tech. 102D and
Novel Netware Server 4.1 Onwards Administrator,
5 Mother Board, 1 GB RAM, 160 1
with Software Computer
HDD, 1000 MBPS NIC, 17" TFT
Network
P-IV 3.06 GHz,102-D
Client Machines with Windows NT,
Motherboard, 512 MB RAM,
6 Windowx XP, Windows 2000, 20
80GB HDD, 15" TFT, 1000 MBPS
Windows 98, Unix Client Software
NIC
7 UPS System 5 KVA Online, 4 Hrs. Backup 2
SVGA 800x600 Lamp Life Span
8 LCD Projector 1
(2000-2500 Hrs)
9 HUB 16 Port 2 For
Broadband/
10 Modem External Modem 56 KBPS 1
ISDN/PSTN
11 ISDN Router 5 Port 1 Internet
12 Ethernet Switch 24 Port 1 Connectivity
Laserjet 30 PPM 16 MB RAM
13 Printer
1200 DPI 1
14 Printer DMP 132 Column. 1
15 Scanner A4 Size 1
16 MS Office Office XP 20 User
Online Protection with Firewall
17 Antivirus Software 20 User
securities
18 ORACLE 8.0 Onwards 20 User For DBMS,
19 SQL Server Prof. Edition 20 User RDBMS
20 Visual Basic/ Visual Studio 6.0 Onwards 20 User Practicals
Page 14
With all Netwrok Tools (Clamping,
21 Network Toolkit 4
Network Tester etc.) For Netwok
RJ-45, 1000 MBPS NIC, UTP Installation
22 Other Network Accessories Cable, T-Connector, Optical -- Practicals
Fibre,Coax Cable 50 Ohm.etc.
Page 15
Annexure-II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Desired Equipment/Hand Tools)
(Optimal Equipments)
Minium
Remark if
Sr.No. Name of Equpt./Machinery Technical Specification Qty.Nos
any.
Required
P-IV-Dual Core Tech. 102D
1 Windows 2003 Server with S/W Mother Board, 1 GB RAM, 160 1
HDD, 1000 MBPS NIC, 17" TFT
Page 16
28 Test Management Tool Test Director 20 User
29 UML Prof. Edition 20 User
All the
30 VB Dot Net Prof. Edition 20 User
systems
31 ASP Dot Net Prof. Edition 20 User
32 ORACLE 8.0 Onwards Prof. Edition 20 User
must be
Online Protection with Firewall connected
33 Antivirus Software 20 User with Internet
securities
Laserjet 30 PPM 16 MB RAM ISDN/PSTN
34 Printer /
1200 DPI 1
35 Printer DMP 132 Column. 1 Broad Band
36 Scanner A4 Size 1 Services.
Page 17
Annexure-II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Desired Equipment/Hand Tools)
(Optimal Equipments)
Page 18
Annexure-II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Desired Equipment/Hand Tools)
(Optimal Equipments)
Minium
Remark if
Sr.No. Name of Equpt./Machinery Technical Specification Qty.Nos
any.
Required
With inbuilt Power supply 5V,
12 V, Logic Switches 12 Nos.,
LED output 12 Nos., 7
Digital Trainer Kit/Component
1 Segment Display 2 Nos., Bread 10
Development System For
Board, Clock Generator 0.1
Conducting
Hz., 1 Hz, 10 Hz, 100 Hz, 1
the practicals
KHz.
of subject
2 Universal Shift Register Kit Demo. Kit 1
Digital
Dcade Counter Using IC 7490
3 Demo. Kit 1 Technics for
Kit
Second Year
4 3 Bit Synchronous counter Kit Demo. Kit 1
CO
5 A to D Converter Kit Demo. Kit 1
6 D to A Converter Kit Demo. Kit 1
7 CRO 20 MHz. Dual Channel 5
8 Logic Analyser 18 Channel 500 MHz. 1
Page 19
Annexure-II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Desired Equipment/Hand Tools)
(Optimal Equipments)
Minium
Remark if
Sr.No. Name of Equpt./Machinery Technical Specification Qty.Nos
any.
Required
P-IV 3.06 GHz,102-D
Motherboard, 512 MB RAM,
1 Personal Computer 20
80GB HDD, 15" TFT, 1000 MBPS
NIC
2 Windows XP Prof Edition 20 User
3 MS Office Office XP 20 User
4 MS DOS 7.00 Onwards 20 User
5 UPS System 5 KVA Online, 4 Hrs. Backup 2
SVGA 800x600 Lamp Life Span
6 LCD Projector 1
(2000-2500 Hrs)
Laserjet 30 PPM 16 MB RAM
7 Printer 2
1200 DPI
8 Printer DMP 132 Column. 2
9 Digital Multimeter 3 & 1/5 Digit 1
10 CRO Dual Channel 20 MHz. 1
11 8085 Microprocessor Kit 8085 with Power Supply 20
8086 MP. Kit with Inbuilt
12 8086 Microprocessor Kit 20
Assembler
13 8085 Assembler Software MASM 20 User
14 8086 Assembler Software MASM 20 User
15 80286 Assembler Software MASM 20 User
16 80386 Assembler Software MASM 20 User
17 80486 Assembler Software MASM 20 User
18 P-IV Assembler Software MASM 20 User
19 8051 Micro Controller Kit Complete Set. 20 User
20 8051 Cross Assembler Software With Editor 20 User
Page 20
MAHARASHTRA STATE BOARD OF
TECHNICAL EDUCATION, MUMBAI
DIPLOMA IN INFORMATION
TECHNOLOGY
(IF)
(AICTE Approved Course)
INDEX
Sr.No. Name of Annexure Name of Lab. Page No.
Programming Lab. 1
Hardware Lab. 2
Network / Internet Lab. 3
Annexure-I (Essential Multimedia Lab. 4
1
Equipment ) Basic Electronics Lab. 5
Digital Lab. 6
Communication Lab. 7
Microprocessor Lab. 8
Programming Lab. 9
Hardware Lab. 10
Network / Internet Lab. 11
Annexure-II (Desired Multimedia Lab. 12
2
Equipment) Basic Electronics Lab. 13
Digital Lab. 14
Communication Lab. 15
Microprocessor Lab. 16
Annexure-I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Essential Equipment/Hand Tools)
(Required for Conducting The Practicals)
22
Logic Analyser 18 Channel 500 MHz. 1
23
CIVIL ENGINEERING
(CE/CS/CR)
1
INDEX
Sr. No. Essential Equipments Labwise Page No.
1 Surveying 1
2 Hydraulics 5
3 Environmental Engineering 7
4 Computer Laboratory 11
5 Model Room 12
6 Transportation 16
7 Surveying 17
8 Hydraulics 18
9 Environmental Engineering 19
10 Computer Laboratory 20
11 Model Room 21
12 Transportation 22
2
ANNEXURE-I
MSBTE NORMS AND STANDARDS FOR EQUIPMETNS
LIST OF EQUIPMENTS & MACHINERIES
( Essential Equipment/Hand Tools)
(Requied For Conducting The Practicals)
Intake - 60
1. Name of Coruse / Department - Civil Engg. / Civil & Rural Engg. / Construction Technology
2. Name of Laboratory - Surveying
Minimum
Name of Equipt.
Sr. No. Technical Specification Qty.Nos Remark if any
/ Machinery
Required
1 Ranging Rods Circular / Octagonal Ranging Rods 100 Nos
preferabally circular with 3 to 5cm
diameter made up of either seasoned
solid bamboo sticks or metal conduit
pipes of lengths 2 to 3 meters, with
conical metallic shoe fitted at bottom &
fully painted with 20 cm.
long colour bands of either of the
following combinations:- a) Black &
White b) Red & White
3
3 Metallic Tape Tape consists of 12 to 15 mm wide strip 15
of either Yarn coating or linen or cloth /
or plastic coating. having very fine brass
or copper or bronze wires. woven into it.
to prevent it from elongation and twisting
. Graduated in metric system. Each
meter length is divided into decimete and
centimeters it is available in various
length. 30 meter length is in common use.
The tape is available in a
leather / suitable cover with a winding
device. The Zero end of the tape is
provided with a metal ring.
4
9 Levelling Staff i) Made of Aluminium body Telescopic in 10
3 PCS, 4 meter in length packed in canvas
cover, graduated in meters, dm, cm and
mm with white background and black
strips. 5mm thick with suitable locking
arrangement. ii) Made of Aluminium
body / Metalic Body folding in 2 PCS, 4
meter in length graduated in meters, dm,
cm and mm. With white background and
black strips. 5mm thick with suitable
folding & locking arrangement.
5
16 Plane table Best quality Indian make plane table size 10
75 cm x 60cm complete with trough
compass in wooden case, 15cm spirit
level 60-75cm long folding alidade and
plumbing fork with plumb-bob.
6
20 Electronic Digital Thedolite ETH 302 Magnification 30x objective 2
(1 second accuracy) aperature 45 mm resolving power 3"
fieldof View 10 30 minimum focusing
disance 1.35 m stadia a ratio 100 stadia
constant 0 focussing 2 speed angle
measurnment type incremental reading
system vertical single horizontal dual
minimum display 5"/1 magon (1'/5"
selectable) 0,2/1magon) accuracy beam
18723 2" 0.6 Magon unit of angle 360
degree / 400 g /6400mil type dot matrix x
LCD DISPLAY PANEL 2 SIDES matrix
x LCD DISPLAY PANEL 2 SIDES Key
panel English Vertical axis compensator
Water resistance - Single axix yes Plate
vial 30"/2mm circular 30 " /2 mm circular
8'/2mm warning buzzer optical plumet
telex Magnification focus range 3x0.5
power soruce Type operation time 4xAA
dry battery, Alkaline 30 Hrs(NIMH 15
Hrs) Ambient Temperature -20+50 degree
celcius size weight body weight
W168/H330xl158mm 4.6 Kg /10lbs
Recharging time at 25 Deg celcius (77D
Far)
7
22 Total Station Laser class *1 Classs 3 R laser product 1
Telescope : Fully transiting coaxial
sighting and distance measuring optic
Magnification / Resolving Power 30x2.5"
Others : length 171 mm (6.7") objective
aperature 45 mm (1.8inch)
(EDM48mm(1.9in) Image Erect field of
View 1deg 30' (26m/1000m) Minimum
focus 1.3m (4.10ft) reticle illumination 5
brightness levels. Angle measurenment:
Photo electrical absolute incoder scanning
both circles adopt diameterical detection.
Unit / Display resolutions. Degree /
Gon/Mil selectable / 1"/5" 0.2 /1 Mgon,
0.005 /0.02mil selectable. Accuracy (Iso
17123-3:2001)3"/1mg/0/015mil
Measuring time :0.55 or less continuous
Measurnemnt Mode : H Clockwise /
Counter-Clockwise selecttable 0 set Volt
andgle input Repetation avaialble. V
Zenith 01 Horizonatal 0/horizontal + -
slope in % selectable. Automatic Dual
axis Compressor Dual axisliqud till +
sensor working range +- 3 feet (+- 55 mg)
Collumination Compensation on /off
selectable Fine motion Scres 1 speed
motionDistance measurnment class 1
equivalent (max. 0.22 mw) Measuring Ran
8
ANNEXURE-I
MSBTE NORMS AND STANDARDS FOR EQUIPMETNS
LIST OF EQUIPMENTS & MACHINERIES
( Essential Equipment/Hand Tools)
(Requied For Conducting The Practicals)
1. Name of Coruse / Department - Civil Engg. / Civil & Rural Engg. / Construction Technology
2. Name of Laboratory - Hydraulics
Minimum
Name of Equipt.
Sr. No. Technical Specification Qtty.Nos Remark if any
/ Machinery
Requied
1 Simple Pitot tube Glass tube made from Borosil (corning )
glass, one end bent at 90 degree and 2
height 500 mm
2 Prandtl Pitot tube
(Static pitot tube) Cylindrical shape with blunt nose made
from brass chromium plated bent at right
angle with standard diameter and length. 1
Height 500 mm with arrangement for
attaching to manometer.
9
7 Apparatus for Verification
10
10 Apparatus for determination
of Minor losses in pipes The appratus should consists of G. I.
Pipes flow circuits with different pipe
fittings, sudden contraction sudden
enlargement, bend, elbows and different 1
valves Pressure tappings should be
provided on upstream and downstream
ends of these fittings, with valve at the
outlet end to regulate the discharge.
11 Venturimeter
Venturimeter made up of brass or
stainless steel with flanged ends. The
throat diameter being 1/3 to 1/2 the inlet
diameter. The anagle of convergent cone
being 20 degree and divergent cone 5
degree to 7 degree. The Venturimeter
should be provided with pressue tapping
at entrance and throat. to 7 degree. The
Venturimeter should be provided
12 Adjustable Channel
11
13 Apparatus for conducting
orifice and mouthpiece
experiments M. S. tank of 450mm x 1200 mm high
with provision for fixing the various
orifices and mouth pieces (inter
changeable). The tank should have
overflow pipe and gauge with scale, for
measuring the X- Y pipe and gauge with
scale, for measuring the X- Y co-
ordinates of jet coming out of orfice /
1 each
mouth piece, sliding attachement with
horizontal and vertical scale accurate to
1mm with vernier reading to 1/10mm
complete with fixing arrangement to the
tank complete with fixing arrangement to
the tank A Set of Orifices- I) 10 mm dia
ii) 15mm dia. iii) 20 mm dia. jv) 25 mm
dia side traingular. A set of mouth pieces.
i) 10 mm dia x 25 mm length ii) 10 mm
dia x 40 mm length
14 Hook guage or pointer guage
Best quality guage comprising a scale and
vernier to read upto o.1 mm. The round
brass pipe scale slides vertically by rack 1
and pinion arrangment. The unit is fitted
with a hook or pointer and complete
outfit is fitted to a suitable C. I. Bracket.
15 Water Current Meter
Cup type current meter with front hoop to
protect the current meter from floating
debris. The current meter should have an 1
arrangment of suspension cable with lead
wieght for measurnment in shallow and
deep water.
16 Centrifugal Pump An all metallic section cut small size
demonstration model made of cast
aluminium parts. Rotator presses water 1
outward by centrifugal action. Complete
on a C. I. Base with a pulley.
17 Reciprocating Pump An all metallic section cut small size
demonstration model made of cast
1
aluminum parts. Complete on a C. I.
Base with a pulley.
18 Water Meter Water meter of standard make 1
19 Water Collecting tanks i) Size 800x800x900mm or of suitable 1 each
size as per rquirement made of M. S.
Sheet with guage glass tube, drain cock
and scale calibrated in cm / mm and litres.
ii) Size 800x300x300mm or of suitable
size as per reuirement'with guage glass,
scale and drain cock
12
ANNEXURE-I
MSBTE NORMS AND STANDARDS FOR EQUIPMENTS
LIST OF EQUIPMENTS & MACHINERIES
( Essential Equipment/Hand Tools)
(Requied For Conducting The Practicals)
Intake - 60
1. Name of Coruse / Department - Civil Engg. / Civil & Rural Engg. / Construction Technology
2. Name of Laboratory - Environmental Engineering
Minimum
Name of Equipt
Sr. No. Technical Specification Qty.Nos Remark if any
. / Machinery
Required
1 Turbidimeter (Jackson) Jackson Terbidimeter with graduated 1
glass turbidity tube, tubular metal shield
standard candle and support in
accordance with A.P.H.A. Standard
method for the Estimation of Water, and
sewage. The turbido tube has flat
polished bottom, and is graduated from 0
to 25 centime. in 1 mm division and from
100 to 5000 parts per million.A spring
beneath the candle keeps it pressed
against the top of the candle holders,
which is 76 mm below the bottom of the
tube. Overall height including glass tube,
22 inches long Accessories and
Replacement Parts: Tube turbidometer
Exax with bottom and fused in white
filter in markings Graduated to 25 cm in
1mm division & with turbidity scale
indicating per million reading from 100 to
5000.
13
2 Digital Turbiditimeter Range: From 0 to 500 NTU in four 1
decadic ranges of 1, 10, 100 and 500
NTU Accuracy: +- 1% of full scale in 10
& 500 NTU ranges Drift / Osicllation:
0.02 NTU due to particle movement
Supply: 230v AC + - 10% at 50 Hz.
Power consumption 25 VA approx.
Standard accessories: i) Box containing 4
nos. of matched flat bottom test tubes of
size 23 x 30 mm ii) Cell riser for 0-500
NTU range iii) Light shield. Panel
Controls: Power : To switch On the
instrument Set Zero: Coarse and fine
control adjusts the meter indication to
ZERO for distilled water Calib.: Adjust
the NTU value on meter scale as per the
standard solution Range: Selects 0 to 1,
10, 100 and 1000 NTU ranges as per the
standard solution.
14
4 Water Distillation Unit Dimesnion PH4 50CMX15CMX45CM 1
Weight 6kg approx Electircals 220/240 v
50/60 Hz. Single phase Power 3KW
Heater Water Supply Min Flow rate 1
litre/min. Min Pressure 3 p.s.I. (0.2x105
NM Square) Features : Abundant Output ,
The still provides 4 Litres/Hrs. of distilled
water produced through a power input of
3KW by a Chromium Plated heater
housed in ahorizontal borosilicate Glass
Boiler . Distilled output is cool ensured
by a high efficiency condenser,.
Temperature of distillate 25deg C. - 40
deg C tested for ambient room
temperature of 30 deg C. Provision for
wall mounting.
15
6 Respirable Dust Sampler The model consist of main part :- the 1
Control module The contorl module,
houses all the functional parts requied
for the collection of particulate and
gaseous samples. The gaseous
sampling arrangements.Details
specifications are given below. Heavy
Duty Blower : 1.5 M3 /Min free fow
(without resistance) Blower Duty Cycle
: Continuous / 24 Hours Max. with
proper maintenance of carbon brush.
Votage Stabilizer: For rallies blower
motor input 145-275 VAC (Standard)
Output 230 + - / -10 VAC Auto Shut
off Timer : 0- 24 hours Timer Totaliser
: 0-9999 Min Flow Controller : Solid
State continuously variable Flow
Measurnment : U tube manometer
with pitot tube and calibration curve.
Filter Holder Assembly : Fibre with
EPDM gasket. Filter Paper : 25cm x
20 cm (overall) Dimension L 23 cm x
18 cm (effective) Option : Brushless
motor, specifications 0.5 HP, 3000
RPM, AC single phase motor 1.6
m3/min. Particulate Sampling: From
100 microns to 0.1 micron depending
upon the type of filter paper used.
Particulates above 10 micron upon
the type of filter paper used Particulat
16
7 UV Visible Spectro Photo Wavelength range: 190nm - 1100nm 1
Meter with PC compatible Baselines flatness : Within =/- 0.002 Abs
with a Pentium-IV is except shock noise Light Source :
recommanded & Graphic 50Whalogen lamp Monochromator :
Printer or Plotter aberrtion corrected concave blazed
holographic grating is used. Detector :
SiPD Silicon Photodiode.Sample
Comparment : Inside dimension: 110 Wx
2300X105h(mm) Beam seferation :
100mm. Maximum allowable path length
for cell : 100mm Beam size 1W x 10 M
(mm) at the center Ambient temperture :
15-35 0c. Ambient humidity : 45% - 80%
(less than 70% at temp 30degC) Power
requirement : AC 100 V , 120V, 230V,
240V(opticalbench) Dimension:
Photometer unit: 550W x 470D x 200H
(mm) Weight : Photometer unit : 17kg.
Basic measurement modes : Spectrum,
Kinetics File Function : Open / Save /
Save as ASCII Export / Import (Spectrum
Only) Data processing : Arithmatic
calculation of spectrum and constant
value, Aritmatic calclation between two
spectra smoothing, Display : Data output
to printer (free formating) Direct reading
of wavelength and photometric values
using cursor, exapansion and expression
of scale by numeric value setting or mouse
17
8 UV Probe Personal SoftwaUv Probe includes four basic components 1
* A Spectrum modle for wavelength
scanning and analysis * S Kinetics
module for Time course measurnment
and Michaelis-menten calculations. * A
Photometric module for quantitative data
analysis * A powerful and flexible Report
Generator that is used to which can be
instantly printed from within any module.
Other features include: * An intutive
screen layout that can be customized for
simple layouts with Instrument History
and satus displays, as well as multiple
graphs and tables. Instant machine control
with real-time feedback, including
onscreen readings of absorbance,
transmittance, energy,, or reflectance
values. * Flexible output to files and
priters. * Various tables used to display,
collect and control data. * Three graph
modes to display data while being
collected or after it is collected. *
Numerous othr post-processing
procedures, such as Point Pick, and Peak
Area. * Import and export features used
to share data with other Windows
applications. * Comprehensive Online
Help, including context-sensitive Help for
18
10 Digital pHMeter Display : 31/2 Digit 12.7 mm LED Range 1
: pH 0.00 to 14.00 mv Accuracy :0.01 pH
+ - digit Temperature Compensation :
0.100 Deg Manual , 540 Atomatic Power
Supply 230 V = - 10 Hz Recorder Output
100m V/ pH Ds Titration Output :
Polarization current outpur provided
Approx Diam in mm (HXWXD) :
60X255X180 Approx Weight : 1. 4 kg
Standard accessoreis: Buffer solution pH
4 & 7 125 ml each Electrode Stand with
clamp Optional Accessories: Buffer
solution pH 4 & 7 125 ml each Electrode
Stand with clamp
19
ANNEXURE-I
MSBTE NORMS AND STANDARDS FOR EQUIPMENTS
LIST OF EQUIPMENTS & MACHINERIES
( Essential Equipment/Hand Tools)
(Requied For Conducting The Practicals)
1. Name of Coruse / Department - Civil Engg. / Civil & Rural Engg. / Construction Technology
2. Name of Laboratory - Computer Laboratory
Minimum
Name of Equipt.
Sr. No. Technical Specification Qtty.Nos Remark if any
/ Machinery
Requied
1 Desktop Computer P-IV Processor -core 2DEo Motherboard
D102 Ram 1GB RAM (DDR-2), DVD
Writer TFT 17" View Inch View Sonic,
21
160 GB SATA HDD, Multimedia
Keyboard , Optical Mouse, UPS, Speaker
(Without Woofer)
2 LCD Projector Latest 1
3 Printer Lazer Jet 1020 2
4 Inkjet A3 Size 1
5 Plotter As per rquirement 1
6 Memmroy Stick ! G.b 2
7 Digital Camera 2
8 Scanner Flat Scanner 2
Softwares
1 + 20
1 Operating System Windows XP Paper Lisc
2 Softwares Autocad 1+ 20 Paper
Liscence
20
ANNEXURE-I
MSBTE NORMS AND STANDARDS FOR EQUIPMENTS
LIST OF EQUIPMENTS & MACHINERIES
( Essential Equipment/Hand Tools)
(Requied For Conducting The Practicals)
1. Name of Course / Department - Civil Engg. / Civil & Rural Engg. / Construction Technology
2. Name of Laboratory - Model Room for Civil Engg.
Minimum
Name of Equipt.
Sr. No. Technical Specification Qtty.Nos Remark if any
/ Machinery
Requied
1 Specimen of materials in Glass box Size 150mm x150mm
Glass box. x200mm with lid, labelled, mark
with relevent IS Code
A : Sample of lime 2
B: Sample of Cement(OPC,PPC 4
rapid hardning, white cements
C: Water proofing Materials 4
D; Admixture for Concrete 4
E: Paints, Varnishes, Pigments, Cement
paint, Distemper, Polishing Materials or 8
Wood
F: Tar & bituman 2
G: Adhesives 4
2 Specimen of Building A: Bricks about 50 nos.
mateials
Properly Constructed model of Ten
Different Kinds and in 1/3 full size
complete mountd on a based board with
nomenclature. i) Full size of brick with
frog ii) Half bat iii) Three Quarter bat iv)
King Closer v) Queen Closer vi) Queen
Closer quarter vii) Bevelled bat large viii)
Bevelled bat small ix) Bull nose x)
Splayheader 1 each
B: Rocks 4
C: Aggregates 12mm, 20mm, 40mm 1 each
D: Sand 2
E: Plywood of different grades, Sample of
Size 200mmx200mm 1 each
22
7 Model for Roof Rain water Showing details of Pipes and disposal of
Harvesting System Water on a board of size 0.6 meter x 1
meter or of suitable size as per
availabililty for building model with flat
and pitch roof. 1 set
8 Cut Section Model i) Sluice Valve, 100 mm dia 1 each
ii) Reflex Valve 100 mm dia
iii) Buttefly Valve 100 mm dia
iv) Wheel Valve 100 mm dia
v) Bib Cock
vi) Consealed Cock
vii) Piller Cock
viii) Angle Cock
ix) S trap
x) P Trap
xi) Nhani Trap
xii) Bottle Trap
xiii) Europian type WC pan
xiv) Orrisa Type WC Pan
xv) Wash & Basin
xvi) Kitchen Sink
23
10 Model of Bridges Different types of Brideges 1 each
Size of each model 1.5 Meter x 0.6 Meter
or as available
I) Arch Bridge ii) Slab Bridge
iii) Suspension Bridge
iv) Cantilever Bridge
v) Bows string gurder bridge
vi) Plate Girdle bridge
vii) Culverts
viii) Cause ways
ix) Bearing for girders.
25
14 Models of Foundations i) Model of Spread footings Size 60 x 30 cm 1 each
ii) Model of Grillage foundation A
properly constructed model of cast
aluminum and metal parts showing
concrete footing grillage on plateform of I
beems. Antivibration mat, base plate and
columan. Complete on wooden base of
size 30 x 25 cm.
ii) Model of Raft Foundation Size : 60cm x 60cm
iii) Piles foundation Size 60 x 60 cm
v) Model of well foundation Size 60 x 60 cm
vi) Model of Scaffolding and shoreing
a) Bricklayer's Scaffolding Showing
ledgers putlogs, standards, brace and wall
size 50x20x40 cm. Approx
b) Racking shore : A properly constructed
wooden model, showing rider, braces sole
piece, cleats, wall and wal plate etc.
complete on base with name of parts size
35x20x60 cm
26
ANNEXURE-I
MSBTE NORMS AND STANDARDS FOR EQUIPMENTS
LIST OF EQUIPMENTS & MACHINERIES
( Essential Equipment/Hand Tools)
(Requied For Conducting The Practicals)
Intake - 60
1. Name of Course / Department - Civil Engg. / Civil & Rural Engg. / Construction Technology
2. Name of Laboratory - Transportation Engineering Laboratory
Minimum
Name of Equipt.
Sr. No. Technical Specification Qty.Nos Remark if any
/ Machinery
Required
27
ANNEXURE-II
MSBTE NORMS AND STANDARDS FOR EQUIPMENTS
LIST OF EQUIPMENTS & MACHINERIES
( Desirable Equipment/Hand Tools)
(Requied For Conducting The Practicals)
1. Name of Course / Department - Civil Engg. / Civil & Rural Engg. / Construction Technology
2. Name of Laboratory - Surveying
Minimum
Name of Equipt.
Sr. No. Technical Specification Qtty.Nos Remark if any
/ Machinery
Requied
28
ANNEXURE-II
MSBTE NORMS AND STANDARDS FOR EQUIPMENTS
LIST OF EQUIPMENTS & MACHINERIES
( Desirable Equipment/Hand Tools)
(Requied For Conducting The Practicals)
1. Name of Course / Department - Civil Engg. / Civil & Rural Engg. / Construction Technology
2. Name of Laboratory - Hydraulics laboratory
Minimum
Name of Equipt.
Sr. No. Technical Specification Qtty.Nos Remark if any
/ Machinery
Requied
1 Hydraulics test Bench with
necessary accessories The hydraulics bench with working
surface liner with RRP, Sump, tank and
collecting tank Bench should have close
circuit through which water can be
circulated continuously by centrifugal
pump. The bench with all accessories
should be supported on a steel frame
1
mounted on castor wheel for easy
movement. The bench should have the
following accessories. i) Orfice and
mouthpiece apparatus ii) Losses in pipes
fittings apparatus ii) Bernaulli's theorem
apparatus iv) Pipe friction apparatus v)
Ventrui meter and orfice meter apparatus
29
ANNEXURE-II
MSBTE NORMS AND STANDARDS FOR EQUIPMENTS
LIST OF EQUIPMENTS & MACHINERIES
( Desirable Equipment/Hand Tools)
(Requied For Conducting The Practicals)
1. Name of Course / Department - Civil Engg. / Civil & Rural Engg. / Construction Technology
2. Name of Laboratory - Envirnmental Engineering Laboratory
Minimum
Name of Equipt.
Sr. No. Technical Specification Qtty.Nos Remark if any
/ Machinery
Requied
1 Digital Sound level Meter Display: LCD with bargraph Microphone:
Description : Microphone, 0.5" (10mm) Electret Condenser
LCD Display, on-off Measurnment Bandwidth L 300 Hz. To
buttion, A./C weighting 8Khz. Measurnment Range: 40 to 130 dB
selection button Min / Max (A wtg). 45 to 130 dB (Cwtg) Frequency
Record button Range weighting : A and C (selectable) (under
selector button F/S reference condition) / 0.1 dB Accuracy /
response selection button Resolutio n 2 dB ( Under reference
Max Hold selector button condition_ Response time : Fast :125
Calibration adjustment AC milliseconds / slow:: 1 second Calibration
analog output jack source : 1Khz sine wave @ 94 or 114 dB
Windscreen AC output : 0.707 Vrms full scale Power :
4 AAA Batteries. Fattery life : 30 hours
(typical) ; low battery indicator alerts user
After apoprox. 20 minutes Operating
temperature 32 to 122 deg. F (0 to 50 Deg
C) Operating humidity : 10 to 90% RH
Storage Temperature - 4 to 140 Deg F (-
20 to 60 deg Cent) Dimensions/ weight :
9x2.3x1.7" (230x57x44mm)/60z (172g)
30
ANNEXURE-II
MSBTE NORMS AND STANDARDS FOR EQUIPMENTS
LIST OF EQUIPMENTS & MACHINERIES
( Desirable Equipment/Hand Tools)
(Requied For Conducting The Practicals)
1. Name of Course / Department - Civil Engg. / Civil & Rural Engg. / Construction Technology
2. Name of Laboratory - Computer Laboratory for Civil Engg. Branch
Minimum
Name of Equipt.
Sr. No. Technical Specification Qtty.Nos Remark if any
/ Machinery
Requied
31
ANNEXURE-I
MSBTE NORMS AND STANDARDS FOR EQUIPMENTS
LIST OF EQUIPMENTS & MACHINERIES
( Desirable Equipment/Hand Tools)
(Requied For Conducting The Practicals)
1. Name of Course / Department - Civil Engg. / Civil & Rural Engg. / Construction Technology
2. Name of Laboratory - Model Room for Civil Engg.
Minimum
Name of Equipt.
Sr. No. Technical Specification Qtty.Nos Remark if any
/ Machinery
Requied
1 Model of Construction i) Scrapper (working model with 1
Machinary diving unit)
ii) Dizer (working model with
diving unit)
iii) dragline (working model with 1
diving unit)
iv) Clamshell (working model 1
with driving)
v) Hoe (working model with 1
with driving)
vi) dregdger on pontoon 1
(working model with driving)
vii) Motor Grader 1
(working model with driving)
viii) Loader 1
(working model with driving)
ix) Trencher 1
(working model with driving)
x) Sheep-foot roller 1
xi) Three Whjeeled and tenden 1
Roller
xii) Three Sheeled and tenden 1
Roller
xiii) Hoist 1
xiv) Belt Coneyer 1
xv) Rope Conveyer (Cable way)
2 Model of Railway I) Permanent way in embankment and
cutting sowing ballast, sleepers, rail
fixtures 1
ii) Specimen of different tupes of rails,
chairs, keys, fishplates Sleeepers 1
iii) Points and crossing 1
iv) General layout of a wayside, Railway
station 1
v) Interlocking 1
32
3 Model Charts i) Loads, Dead Load, live Load, Wind
Load on structures 1
ii) Loading on Bridges 1
iii) Manufacture of bricks 1
iv) Manuacturing of Cement 1
v) Concrete Batching and 1
Mixing Plant Readymix Concret
vi) Hot mix plant 1
33
ANNEXURE-II
MSBTE NORMS AND STANDARDS FOR EQUIPMENTS
LIST OF EQUIPMENTS & MACHINERIES
( Desirable Equipment/Hand Tools)
(Requied For Conducting The Practicals)
1. Name of Course / Department - Civil Engg. / Civil & Rural Engg. / Construction Technology
2. Name of Laboratory - Transportation Engineering Laboratory
Minimum
Name of Equipt.
Sr. No. Technical Specification Qtty.Nos Remark if any
/ Machinery
Requied
Bituman Testing Appratus
34
MAHARASHTRA STATE BOARD OF
TECHNICAL EDUCATION, MUMBAI
1 Garment construction 1
2 Drafting 3
3 Illustration 4
4 Embroidery 5
5 Textile Testing 6
6 Computer 9
8 Illustration 12
9 Textile Testing 13
10 Computer 14
ANNEXURE I
NO DESIRED EQUIPMENT
ANNEXURE II
DIGITAL ELECTORNICS
(DE)
2 Electrical Engineering 3
6 Electrical Engineering 14
Page 3
AC/DC Voltage, AC/DC Current,
12 Analog Multimeter 2
Resistance Measurement
13 RF Signal Generator Range 0-30MHz 2
14 Digital Storage Oscilloscope Dual Trace 150 MHz 1
Bread Board with Power ± 5 Volts, Logic Switches, LED
15 5
Supply Indicators, Pulser Key
Test Range:
Microprocessor (
8085/8086/8088/6502)
16 Analog \ Digital IC Tester 74/54/40/45/93 series Ics, 2
EPROMs,RAMs, OP-Amp;
Comparator Ics; Optocouplers
Transistor Tester hfe : 0-3000; Ic/Ib: 0-300 mA DC; 2
17
Ic/Ib : 0-3 mA DC
Page 4
ANNEXURE- I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES ( Essential Equipment / Hand Tools)
(Required For Conducting The Practical.)
Page 5
( 0 - 500 v ) 5
15 D.C. Ammeter ( 0 - 50 µA ) 5
( 0 - 100 µA ) 5
( 0 - 50 mA ) 5
( 0 - 100 mA ) 5
( 0 - 500 A ) 5
(0-1A) 5
( 0 - 5A ) 5
16 A.C. Ammeter ( 0 -500 mA) 5
( 0 -1 A) 5
( 0 -5 A) 5
( 0 -15 A) 5
17 Rheostats ( 100 Ω , 2A ) 5
( 320 Ω , 2A ) 5
( 500 Ω , 2A ) 5
( 1 KΩ , 2A ) 5
Displacement 0-5mm or 0-10mm,air
18 LVDT core, On board digital panel meter with 2
displacement signal
19 RTD - (PT-100) 0 - 100 / 200°c 1
20 Thermocouple Copper-Nickel 185 to 300°c 1 Any type
21 Hygrometer 20-100 RH 2
Length-500mm, A-75mm,foat material
Acrylic \ Glass Tube Rotameter
22 SVS/PVC/Teflon Approx. Pressure loss 1
\ Venturi \ Orifice
mm/sec:200-300
20°c water max flow &20°c air flow
L/min:0.1-1,dimension:114mm,Max up
23 Air Purge Rotameter Pressure:10kg/cm2 flow direction: Bo 1
Hm Rear to Top rear, Melting Type:
Borosilicate Glass, float ss316?Teflon
Page 6
Test pins for
Strain Gauge/Dead Weight Measurement upto 0-15kg,Output
24 2 monitoring
Pressure Gauge Tester available for control &monitoring
25 Rotary Encoder with Digital Pulse Output 1
Measurement Ranges : C = 0 - 9999
µF, L = 0 - 9999 H, R = 0-100MΏ
26 LCR - Q Meter 2
Measurement frequency :User
Selectable
AC/DC Voltage, AC/DC Current,
27 Analog Multimeter 4
Resistance Measurement
100KHz to 110MHz (CW mode), with
AM/FM Generator(RF
28 frequency indication, RF o/p 2
Generator)
75mVolts(rms),O/P control 0 to 20dB
29 Digital Storage Oscilloscope Dual Trace, 150MHz 1
A.C / D.C. Position Control
30 12V DC Servo Motor 2
System
selectable
PID controller with Load On /Off control action, PID and any
31 (Oven/any) Hysterisis selection, 4 load
(Temperature Control System) P = 0 -10, I = 0.0 - 0.02, D = 0-20 considered
as plant
Synchro Transmitter - Receiver
32 90/115V ,60Hz 4
System
33 Servo Stabilizer 180-270V,1KVA 4
Resistor, Capacitor & Inductor
34 Selectable ranges 2
Bank
35 Lamp Bank 230 V,1KW 3
36 Resister Load Bank 230 V,1KW 3
Trainer Kit to verify
37 Characteristics of SCR/ Diac/ Inbuilt Power Supply 1 each one
Triac / IGBT
Page 7
ANNEXURE - I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES ( Essential Equipment/Hand Tools )
( Required for Conducting The Practicals )
Page 8
8 Graphic equalizer 5+5 band ±10-15 db variation 4
with
different test
points for
pre amplifier
9 DVD/VCD/CD Player 5.1 channel ,AV input 2 ,output
amplifier,
drive
mechanism
with test
points of
different
stages for
fault finding,
observation
of
signals,volta
ges(Chroma,
Video
10 Colour TV Reciver 14/21'' colour CRT 4
amplifier,
system
control,
horizontal
stage,
vertical
stage,EHT
generation,
picture tube
Page 9
With Gunn, klystron power
supply,VSWR meter,& microwave
components gunn
oscillator(10mW),isolator,PIN
Modulator, Slotted Section, Frequency
meter, Variable attenuator, Detector
mount, Tunable Probe, Klystron
Mount, Coaxial Adapter, Phase
Shifter,C.D.coupler 20dB,E plane
bend,E plane Tee, Fixed attenuator,
13 Microwave Test bench 1
Matched Termination, Magic Tee,T -
Circulator, Multiholedirectional
coupler(10dB),SS tuner, Precision
movable short, Slotted Antenna Broad
Wall, Slotted Antenna
narrow,wall,Parabolic Antenna,
Waveguide Cavity, Waveguide Twist,
Dielectric Antenna plane Sectorial
Horn ,Pickup horn, Pyramidical horn,
Standard Gain Horn
Modulation
Transmitter fiber optic LED 950nm
Analog transmitter kit for fiber Techniques
14 IR/660nm red visible and modulation 4
optics analog link PAM,PCM,P
circuit
WM,PPM
Photo diode with resposivity of 0.3µA PC to PC
or photo transistor detector with TTL communicati
Analog transmitter and receiver out put ,FOC-Core on using
15 4 RS232
kit for fiber optics analog link n1=1.492,n2=1.406,na=0.50,aa=
60,fiber diameter=1000 micron, outer
diameter= 2.2 mm length 1m
Microproces
16 EPABX trainer system 2 dot lines,4ext,optoisolation trunk 2
sor based
with test
1 dot line, hand set connection, matrix points for
17 Telephone trainer kit 4
K/B intermediate
signal
with test
1 dot line, hand set connection, matrix points for
18 Cordless Telephone kit 2
K/B intermediate
signal
with test
1 dot line, hand set connection, matrix points for
19 FAX 1
K/B intermediate
signal
Page 10
with test
points for
20 Modem 10 to 100 Mbps 1
intermediate
signal
0.02Hz - 2MHz, DC,Sine,Tringular,
21 Function Generator/counter 6
Square, Ramp,TTL(sync)
22 CRO 20Mhz Dual Trace 6
Page 11
ANNEXURE - I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES ( Essential Equipment/Hand Tools )
( Required for Conducting The Practicals )
Page 12
With 8085A CPU @ 3 MHz, Monitor
FIRMWARE, User Battery Backup
Expandaqble RAM, Display, Keyboard,
Serial I/O using RS-232, Onboard
11 Microprocessor 8085 Kits 10
8155, 8255, 8279, 8253, built in
Assembler & Disassembler, System
Expation Slot, Switch Mode Power
Supply
LED
indicators
for
monitoring
12 8155 Interface Card 6 status of
Ports for
Input-Output
Operation
LED
indicators
for
monitoring
13 8255 Interface Card 6 status of
Ports for
Input-Output
Operation
LED
indicators
for
14 ADC / DAC Cards DAC 0800,ACD 0809 4 monitoring
status of
Control
Signals
LED for
Suitable to drive 2Kg torque Stepper Driving
15 Stepper Motor Card 2
moter Pulse
indication
With 8051 Microcontroller @ 12 MHz,
Monitor FIRMWARE, User Battery
Backup Expandaqble RAM for
program & data, Display, Keyboard,
Serial I/O using RS-232, Onboard
16 Microcontroler 8051 Kits 6
8155, 8255, 8279, Timer & Counter
using 8253 PPI, Single Line Assembler
& Disassembler in Local & Remote
Mode, System Expation Slot, Switch
Mode Power Supply
Page 13
17 CRO 20 MHz, Dual Trace 2
Bread Board with Power ± 5 Volts, Logic Switches,LED
18 10
Supply Indicators, Pulser Key
0.02Hz - 2MHz,DC,Sine,Tringular,
19 Function Generator/counter 6
Square, Ramp,TTL(sync)
3½ digit with AC/DC current,
voltage,resistance,capacitence,frequenc
20 Digital Multimeter 4
y & temperature mesurement alon with
diode,continuity,hfe mesurement
21 Logic probe TTL/CMOS logic indication 2
22 Current Pulser Inject the TTL/CMOS logic 2
Page 14
ANNEXURE- II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES ( Essential Equipment / Hand Tools)
(Required For Conducting The Practical.)
Page 15
ANNEXTURE-II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
Mini.
SR. Name of Equipment /
Technical Specifications Qty./ Nos Remark
NO. Machinary.
Requ.
1 Potentiometer 400cm 1
2 Hay's Bridge 1
3 Sheiring Bridge 1
4 Maxwell's Bridge 1
5 Wheatston's Bridge 1
6 Wein Bridge 1
Provision to
Trainer Kit for Polyphase Controlled Uncontrolled,
7 2 chane Firing
Rectifiers Semicontrolled
Angle
8 Powerscope 3 Channel ,30 Mhz,1500 Vmax 1
9 Galvanometer 30-0-30 mA 1
Selectable
10 Resistor Box 0-5KΩ 1
steps
11 Power Factor Meter (-) 0.5 to (+)0.5 1
12 Megger 500 V 1
13 Frequecy Meter 45 -55 Hz Digital Display 1
selectable
On /Off control action, PID and any
Electronic Controller- PID , On load
14 Hysterisis selection, 1
/ Off considered
P = 0 -10, I = 0.0 - 0.02, D = 0-20
as plant
FrequencyRange: 150 kHz to 1050
15 Spectrum Analyser Mhz; Amplitude Range: -100 dBm to 1
+13dBm
Page 16
ANNEXURE - II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Optional Equipment/Hand Tools )
( Required for Conducting The Practicals )
Minimum
Remark if
Sr. No. Name of Equpt./Machinery Technical Specifications Qtty./Nos
any
Required
with test
1 dot line,hand set connection,matrix points for
1 FAX 1
K/B intermediate
signal
with test
points for
2 Modem 10 to 100 Mbps 1
intermediate
signal
3 Distortion Meter 20 Hz-20 KhZ,3 digit Display 1
Page 17
ANNEXURE - II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES ( Optional Equipment/Hand Tools
( Required for Conducting The Practical )
Remark if
Name of Minimum any
Sr. No. Equpt./Machinery/software Technical Specifications Qtty./Nos
package Required
Page 18
MAHARASHTRA STATE BOARD OF
TECHNICAL EDUCATION, MUMBAI
4 Electronics Lab. 8
5 Computer Lab. 11
6 Electric Workshop. 12
10 Electronics Lab. 16
11 Computer Lab. 18
12 Electric Workshop. 19
ANNEXURE-1
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
Minimum
Name of Equipt./
Sr.No Technical Specifications Qtty./Nos Remark
Machinery
Reqd
15KVA
Input 415 V, 3 phase, 50 Hz
1 Auto Transformer Output 0-415 V, 30 A per Line 2
Cooling air natural
3 KVA , 3 Phase, 50 Hz
440/230 V
2 Transformer H.V. delta connected 2
L.V. star connected
Page 3
Two D.C. Machines coupled together
3 KW, 13.5 A, 1500 rpm, Shunt D.C. machines
Hopkinsons Test Insulation class “B”
6 01 set
Equipment
25 KVA, To provide
Input :- 415 V , 3 phase 50Hz, 36 A D.C.
7 Rectifier 1
D.C. output :- 0-230V variable ,Current 100A supply
Page 4
7.5 KW , 230V, 3 phase, 4 wire
Balanced load. (Each branch having equal load)
14 Loading Rheostat Load : wire wound fixed resistors 4
Page 5
ANNEXURE-1
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Essential Equipment/ Hand Tools)
(Required For Conducting The Practicals)
Minimum
Name of Equipt./
Sr.No Technical Specifications Qtty./Nos Remark
Machinery
Reqd
AC/DC 0-1 Amp. 5
AC/DC 0-1.5 Amp. 5
1 Ammeters-MI Type
AC/DC 0-2.5 Amp. 5
AC/DC 0-5 Amp. 5
DC 0-0.5 / 1 Amp. Dynomometer type portable
moving coil 150mm 5
DC 0-1.5 / 3 Amp. Uniform Scale with anti
parallax mirror , Knief 5
2 Ammeters-PMMC Type
DC 0-2.5 / 5 Amp. Edge pointer housed in a
teak wood/ eboite case 5
DC 0- 5 / 10 Amp. 1st grade accuracy +-1%
FSD 5
AC/DC 0-150 / 300 V. 5
3 Voltmeters-MI Type AC/DC 0-250 / 500V. 5
AC/DC 0-75 / 150V. 5
DC 0-150V.Dynomometer type portable
moving coil 150mm 5
DC 0-250 / 500V.Uniform Scale with anti
parallax mirror , Knief 5
4 Voltmeters-PMMC Type
DC 0-150 / 300VEdge pointer housed in a teak
wood/ eboite case 5
Precision grade DC 0- 15/30V.1st grade accuracy
+-1% FSD 2
Single Phase 2.5/5 Amp. 200/400 V 5
5 Wattmeters
Single Phase 5/10 Amp. 250/500 V 5
6 Single Phase 5/10 Amp. 250/500 V 5
Low P.F. Wattmeters
7 AC, 230V,45-50-55 Hz 1
8 Power Factor Meter Single Phase 5-10 Amp, 250V. 5
9 Galvanometer (0-30) Class-A 4
10 Digital Temperature Indicato9V, 3 and 1/2 model 310 1
11 Wattmeters DynamoType Single Phase, 5A, 250V. 1
Page 6
600Ω, 1A wire wound resisitors, Variable three
terminal with steel 5
430Ω, 1.5A Clamp+ Brush type moving contact
12 Rheastat
+-5 % Tolerance 5
250Ω, 2.5A 5
120Ω, 4A 5
100Ω, 5A wire wound resisitors, Variable three
terminal with steel 5
450Ω, 1A Clamp+ Brush type moving contact +-
13 Rheastat Variable 5 % Tolerance 5
1000Ω, 0.8A 5
92Ω, 2.2A 5
240Ω, 1.5A 5
14 1-Ph, Loading Inductor 1 Ph,230V, 10 Amp 5
15 1-Ph, Variable Capacitor 2 Ph,230V, 5 Amp 5
16 Dimmerstat Input-230V output 270V 20Amp. 4
single Phase, 50Hz, 230V/20V, 0.5KVA 1
17 Transformer
single Phase, 50Hz, 230V/6-12V, 0.5KVA 2
Scientific , 20MHz, digital storage oscolloscope-
18 Dual Trace Oscilloscope HM205-2 2
19 Braid board Braid board 4
SPDT 4
DPST 4
20 Knife Switches
SPST 4
DPDT 2
21 D.C. Regulated Power Suppl0-30V, 2Amp 5
10kW, 230V 2
22 3-Phase Variable load 20kW, 230V 2
23 3-Phase auto Transformer 230V, 20A 2
Verification of Verification of Superposition Theorem Trainer kit should
Superposition Theorem Kit be totallu
24 Trainer Kit 4 enclosed in
Verification of Thevenin's Verification of Thevenin's Theorem Trainer Kit a
25 Theorem Trainer Kit 4 transparent
Verification of Maximum Verification of Maximum Power Trasfer cabinet, it
Power Trasfer Theorem Theorem Trainer Kit should be
26 Trainer Kit 4 ready to
Verification of Norton's Verification of Norton's Theorem Trainer Kit connet to
27 Theorem Trainer Kit 4 230V,
50Hz, a.c.
Verification of Kirchoff's Verification of Kirchoff's Laws Trainer Kit
supply.
28 Laws Trainer Kit 4
Output
29 CT 25/5 Amp - 100/5 Amp - 1
30 PT 400 V / 100 V , 1
31 Current Tranformer 100/5 2
Page 7
32 Clip on ammeter 2
33 Eleetronic Triveotometer 3 Phase 415 V 20 A - 40 A 2
34 Induction Energymeters 1 Phase 230 V, 10 A 2
35 Induction Energymeters 3 Phase Four Wire, 3x415V, 3x10 A 2
36 Kelvins double bridge with Galvanometer 2
37 Megger as per standard 5
38 Earth Tester as per standard 5
39 Phase Sequence meter Rotating Type 2
40 Potentiometess With Silde Wire 4
41 Lamp Bank 230 V 0-20 A 2
42 Single phase KWH Check M1 Phase, 230 V, 10 A 1
43 KWH Meter 3 Phase , 230 V, 20 A 1
44 Capacitance Bank Local 3 Phase, 230 V , 20 A 1
45 loading Rheostat 1 Phase, 0-7.5 KW
46 VAR Meter as per standard
Page 8
ANNEXURE-1
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
Minimum
Name of Equipt./
Sr.No Technical Specifications Qtty./Nos Remark
Machinery
Reqd
1 Relay Testing equipment Model TRM 100D 1
Motorised oil Test Set Input- 240V, 50Hz, 1-Ph a.c. Output- 0-
2 1
100kV,a.c.
Low tension air circuit breaker.( including
protective devices )Minimum oil circuit breaker (
M O C B ) Miniature circuit breaker ( M C B )
Models of different circuit Moulded case circuit breaker ( M C C B )Earth
3 Leakage circuit breaker ( E L C B ) or Residual 1
breakers
leakage circui ,t breaker ( R L C B ), Sulpher -
Hexa fluoride circuit breaker ( S F 6 ), Vacuum
circuit breaker.,
Should have PSM & TSM Setting Suitable for 5
Over Current relay 1
4 Amp Rating
Page 9
ANNEXURE-I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Essential Equipment/ Hand Tools)
(Required For Conducting The Practicals)
Minimum
Name of Equipt./
Sr.No Technical Specifications Qtty./Nos Remark
Machinery
Reqd
Regulated DC Power (o-35V,0-2A),with overcurrent,overvoltage
1 Supply protection and fine and coarse adjustments with 6
adjustable current limiter
Cathode ray Oscilloscope DC to 20MHz,2Channel, 2mV/Div, sweep delay,
2 invert facility in both channels, squarewave 6
testing
3 Cathode ray Oscilloscope DC-60MHz, 4channel 1
4 Digital Multimeter 3½digit, 29 ranges, 10functions compact DMM 6
5 Analog Multimeter SANWA or equivalent 2
Microprocessor 8085 Intel 8085 with 64 K RAM, keypad for entering
6 trainer kits Hex code, LCD display, RS with necessary 6
interface
7 Microprocessor add-ons Standard interfacing cards for microprocessor kit
8 Study of 8155 at Sr. No. 6
9 Study of 8255
Study of Analog to Digital
10
Converter module
Study of Digital to Analog
11
Converter module
Stepper motor control
12
module one each
Temperature control
13
module
8257 DMA controller
module
8253 timer module
14
Water level control module
Page 10
Educational trainer kits Standard kits for demonstration in laboratory
with built in power supply and indicating devices
15 1
DC position control system favorably with digital indicators.
16 Synchro characteristics 1
17 Synchro as error detector 1
18 Diode characteristics 2
19 Zener diode characteristics 2
20 SCR characteristics 2
21 FET characteristics 2
22 UJT characteristics 2
BJT CE mode
2
23 characteristics
BJT CE mode
2
24 characteristics
25 Single stage CE amplifier 2
26 Two stage CE amplifier 2
27 CB amplifier 2
28 Hartley oscillator 2
29 Colpitts oscillator 2
30 Triac characteristics 2
Integrated Multivibrator
trainer (Astable,monostabe
31 and bistable
Thyristorised speed control
2
32 of DC motor
33 IC723 as voltage regulator 2
Study of logic gates
(Integrated trainer for all 2
34 types of logic gates)
Wall charts for 8085 Standard wall charts showing architecture,
architecture, 8255, control word and pin diagram 1 set
35 8253,8259,8257,8155
Wall charts for construction Standard wall charts showing pin
of basic semiconductor diagram/terminals, block diagram/equivalents,
devices (Diode, BJT, construction etc. 1 set
FET,SCR, DIAC,Traic,UJT
36 etc..)
37 Voltmeters 0-50V with resolution 0.5V 8
0-100V with resolution 1V 4
0-100mV with resolution 0.1mV 4
Page 11
38 Ammeters 0-10A with resolution 0.5A 8
0-100A with resolution 1A 4
0-100mA with resolution 0.1mA 4
0-500µA with resolution 1µA 4
Function Generator standard 1MHz, 0.1v to 1MHz ranges and DC,
sine, triangular,pulse,square,rectangular. Sweep
waveforms, 0-30V Peak to Peak output and 20dB 4
and 40dB attenuation facility, TTL output
39 additional facility
40 Signal generator 10MHz standard 4
41 Digital IC tester Basic logic gate testing facility 1
42 Analog IC tester Standard 1
43 LCR-Q meter Standard 1
44 Breadboard Standard WISH make or Equivalent 10
Page 12
ANNEXURE-I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
Minimum
Name of Equipt./
Sr.No Technical Specifications Qtty./Nos Remark
Machinery
Reqd
P-IV ,2.00 GHz CPU ,256MB RAM, 80GB
HDD,15" monitor,keyboard, Mouse,Network
1 Computer adapter card,1.44 MB Floppy Disk DriveCD- 20
ROM Drive. Pre loaded licensed operating
system
2 UPS 1 KVA, 30 Minute backup 1
3 Printer Dot matrix or inkjet or laser 1
4 HUB/SWITCH 16 port 1
5 P-SPICE software P-SPICE software 1
6 SCADA SCADA software 1
MATLAB 10 User
7 MATLAB simulink 2 user
control system toolbox 2 User
LAPTOP -Computer Note P-IV ,2.00 GHz CPU ,256MB RAM, 80GB
Book HDD,15" monitor,keyboard, Mouse,Network
8 adapter card,1.44 MB Floppy Disk DriveCD- 1
ROM Drive. Pre loaded licensed operating
system
9 LCD Projector Compatible to P-IV Computer 1
10 C Programming Software Turbo - C 20 User
Page 13
ANNEXURE-I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
Minimum
Name of Equipt./
Sr.No Technical Specifications Qtty./Nos Remark
Machinery
Reqd
1 Electric Iron 750Watt, 230 V 1
2 Toaster 500 Watt, 230 V 1
3 Electric Geyser 230 V , 2 K W 1
4 Electic Fan 60 Watt , 230 V 1
5 Mixer & Food processor 230 V , 1.25 Liter 1
6 UPS 2 KVA 230 V With 2 hour Backup 1
7 Invator 800 VA 230 V with 4 hour Backup 1
8 Battery Charger 6 V , 12 V, 24 V Battery 1
9 Air Conditioner 1.5 ton 2
10 VCD/ DVD Player 230 V 50 Hz, 8 Watt 1
11 Micro Oven 230 V Latest Model 1
750 watt Automatic/ Semiautomatic Lastest
12 Washing Machine
Model 1
13 Remote Control T.V. / DVD 1
Page 14
ANNEXURE-II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
Minimum
Name of Equipt./
Sr.No Technical Specifications Qtty./Nos Remark
Machinery
Reqd
Squirrel cage 3 HP/ 2.2 Kw delta connected
2 Induction Motor stator Insulation class “B” 1440 rpm , 440V , 3 1
phase, 50Hz
Motor:3Kw,1500rpm,230V.19.6A,Field:Series
DC compound Motor- Field :Shunt Type:S.P. Rating:Cont.Generator:
4 01 Set
Generator set 5Hp,1440 rpm,230V,22.8A
Field:shuntType:S.P.Rating:Cont.
Motor:3Kw,1500rpm,230V.19.6A,Field:Shunt
DC Shunt Motor- Type:S.P. Rating:Cont.Generator: 5Hp,1440
5 01 Set
Compound Generator set rpm,230V,22.8A Field:shunt Field:Series
Type:S.P.Rating:Cont.
Moter Generator Set 2 No.- D.C.Shunt Moter -
Parallel operation of
6 Alternator Complete Panel with Necessary 1
Alternator Set
Meters
Working demonstration for D.C.Machine,
7 1
Electric Machine Trainer A.C.Machine With different Rotors
3 Phase 3 Wire 110 V, 5 A Class .5/1.0 Moduel
8 1
Electronic Trivector Meter No.ER 300P
9 Dielctric Heating Unit 1 KW, 230 V 1
10 Stop Watch 1/5 Second Accuracy with Metal Body 1
Page 15
ANNEXURE-II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
Minimum
Name of Equipt./
Sr.No Technical Specifications Qtty./Nos Remark
Machinery
Reqd
0-20 A , 0-50 A , Dynomometer type portable
moving coil 150mm,Uniform Scale with anti
1 Ammeters parallax mirror , Knief ,Edge pointer housed in a 2
teak wood/ eboite case,1st grade accuracy +-1%
FSD
40 V, 5 A , 20 V , 10 A , 150 V , 2 A wire wound
resisitors, Variable three terminal with steel,
2 Rheostate 5 each
Clamp+ Brush type moving contact +-5 %
Tolerance,
Single phase Variable 250 V , 2.5 KVAR, 4 A
3 2
Inductor
Standard 1 MHz 0.1 V to 1 MHz ranges and D.C
sine, Triangular, sweep Waveforms, 0-30 V peak
4 Function Generator to peak output and 20 dB and 40 dB attenuation 2
facility, TTL output additional facility.
Page 16
ANNEXURE-II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
Minimum
Name of Equipt./
Sr.No Technical Specifications Qtty./Nos Remark
Machinery
Reqd
Electrical Power System Complete with Accessories - Motor Generator
1 Simulator Set and Transformer with Protective Relays ( 1
230 V AC & 230 DC supply )
Induction Motor Simulator with Facility to create and simulate different
2 1
faults of Inducation Motor
Input 240V, 50Hz, 1-Ph, Output 0-30kV,
Capacity 100mA on H.T. 3KVA Encloser: in
3 AC High Voltage Unit 1
two parts: 1) Control panel Air cooled , 2) H.V.
Transformer oil cooled
Input 240V, 50Hz, 1-Ph, Output 0-5kV A.C.
4 AC High Voltage Unit with one end earth potential, Capacity 100mA 1
on output.
Complete with Accessories - to Simulate short ,
5 Transmission Line Simulator 1
Medium & Long Transmission
Digital Cable Fault locator Model No. 5199
6 1
testing kit
Page 17
ANNEXURE-II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Desired equipments Hand Tools)
(Required For Conducting The Practicals)
Minimum
Name of Equipt./
Sr.No Technical Specifications Qtty./Nos Remark
Machinery
Reqd
DC to 150MHZ, 2Channel, Dual time base,
sampling rate 200MS/s(Real time), Front and
1 Digital storage oscilloscope Reference memory 2K each, pretrigger, roll, 2
envelope and average models, built in RS-232
interface.
Allen bradley 1200 PLC with interface modules
like Water level control, bottle filling plant,
robot arm, stepper motor control, synchronous
motor control, DC motor speed control, Output
2 PLC teaching set devices control module, alarm anunciator, 1
ON/OFF control module, thumb wheel switch,
BCD code generation module with PC interface
and necessary PLC software
Page 18
VLSI system development with VLSI system development facility with
4 platform interfacing with PC, microcontroller and various 1
modules as in 3 above.
3++ GHz, 512MB RAM,80GB HDD, Internet
5 Computer P-IV ready keyboard, optical scroll mouse, 10/100 6
Mbps LAN card, 4 USB ports
6 Printer (Laserjet) HP laserjet 1160 or equivalent 1
1024 x 760, 600 video lines, 2000 lm, 16770000
colors, manual control (Zoom rati 1.1:1),
180W/2000Hrs normal mode, 160W/3000Hrs
7 LCD projector low mode, SVGA, NTSC/NTSC 1
4.43/PAL/SECAM, with PC interface and audio
interface.
8 Paper projector Standard 1
Softwares
MATLAB with all
1
toolboxes
Microwind 1
9 Standard softwares with 10 users licence
20-Sim 1
Electronics workbench 1
p-Spice 1
VLSI-project navigator Free Xillinx download available
10 Microcontroller kit (8031/51 Educational demonstration kit with pgm facilities 1
Page 19
ANNEXURE-II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Desired Equipment/ Hand Tools)
(Optimal Equipments)
Minimum
Name of Equipt./
Sr.No Technical Specifications Qtty./Nos Remark
Machinery
Reqd
Computer P-IV ,2.00 GHz CPU ,256MB RAM, 80GB
HDD,15" monitor,keyboard, Mouse,Network
1 adapter card,1.44 MB Floppy Disk DriveCD- 5
ROM Drive. Pre loaded licensed operating
system
2 UPS 1 KVA, 30 Minute backup 1
3 Printer Laser 1
4 HUB/SWITCH 8 port 1
5 MATLAB 1 Latest Version
6 MATLAB simulink 1
7 control system toolbox 1
LAPTOP -Computer Note Latest Configuration
8 1
Book
9 Pen Drive 1 GB 1
10 Vaccum Cleaner 750 Watts , 230 V 1
11 Air Conditioner 2 ton 1
Page 20
ANNEXURE-II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
Minimum
Name of Equipt./
Sr.No Technical Specifications Qtty./Nos Remark
Machinery
Reqd
With Head Stock and Tailstok wire feed Carraige
Coil Winding Machine and
1 Revolution Counter Wire Gaguge Indicator and
driving Motor
Drive Plate 1
2 Television Colour / Black&White 1
For Testing Armature short circuiting single
3 Internal Growler
Phase 230 V 1
For Testing Armature short circuiting single
4 External Growler
Phase 230 V 1
5 Models Demostration of all electical equipment 1 each
6 Baking Ovan 400 V 3 Phase 3KW 1
7 Knife Switch DP DT, TP ST, TP DT, SP DT 1 each
Page 21
MAHARASHTRA STATE BOARD OF
TECHNICAL EDUCATION, MUMBAI
Communication Lab. 9
PCB Lab. 14
Communication Lab. 19
PCB Lab. 20
Annexure-I
2) Bandwidth – DC to 20 MHz.
3) Sweep Rate – 0.5 sec/div to 0.2 µsec/div.
4) Power supply 230 V +/- 10 % 50 Hz.
2 CRO Power Scope 2
1) 15 Mhz.
2)Deflection factor – 50 mv/div to 200 volt/div.
3) Bandwidth – DC 15 MHz.
4) Sweep rate – 500 ms/div to 0.2 s/div.
5) Calibrator – 1 volt 1 KHz. (Appose) square
wave signal.
6) Max I/P -+/- 1000 vdc or 660 v rms.
7) Power supply 230 v +/- 10 % 50 Hz.
3 Sine square 1) Out Put wave form – Sine, Triangle, Square. 10+2
Oscillator function 2) Frequency range – 0.1 Hz to 10 MHz.
Generator 3) Amplitude Range – 30mv to 30 Volt P P
4) O/P impedance – 50 V.
5) Display – 4 digit LED/ LCD
4 D.C. Power supply 1) O/P voltage – 0 to 30 Volt, 2A in 3 range in 10+2
both channel
2) Display – 3 ½ digit
3) Load regulation – 0.5 v % + 10mv, no load full
4) Line regulation – 0.05 % + 15 mv for +/-
Variation around 230 volt
5) O/P imp – 15 miliohms
6) Ripple – less than 1mv rms.
7) I/P supply – 230 V +/- 10 % 50 Hz.
5 Digital Multimeter 1) DC Voltage : 400mv to 1000 V 10+2
2) AC Voltage : 4 Volt to 750 Volt
3) DC Amp : 4mA to 10 Amp
4) AC Amp : 4mA to 10 Amp.
5) Resistance : 400 Ω to 40 MΩ
6) Capacitance : 4 nf to 200 µf
7) Duty cycle ( % ) 0.1 % to 99.9 %
8) Frequency 10Hz to 10MHz.
9) Temperature : 20°C to 750°C
10) Transistor Test :Yes
11) Diode test : Yes
12) Continuing Buzzer : Yes
13) Power supply 9 Volt
14) Max Display : 3999
6 Electronic Speed 0 to 1500 rpm 1
tachometer
7 Universal motor ¼ HP Single Ph. 1
8 PC Based data 1) I/O 6 Nox of Analog Input. 1
acquisition & 8 Nos of Digital Input
Instrumemtation 8 Nos of Digital output
Trainer 1 No. of Analog output
one digital o/p is internally used for providing 8 bit
port simulator.
9 BENIX PLC 1) CPU & Memory : Microcontroller based with 1
Trainer ladder logic 'memory to store up to 41 rungs.
2) Display : 16 chara. Alphanumeric display with
I/O indication
3) Input 8 Nos of digital with LED indication,
2Nos of Analog I/P, 8 Nos of Analog comparator
4) Output 4 Nos of Energizing coil relay with
indicator & fuse protection
5) latches : 256 No of latch
6) Timer : 8 Nos of programmable timer
7) counter : 8 Nos of programmable counter
8) Power supply : 230 V / 50 Hz +/- 10 %
Annexure-I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Essential Equipment / Hand Tools )
( Required For Conducting The Practicals )
Name of Course :- Electronics & Communication
Name of Laboratory :- :- Digital Electronics & Microprocessor
1 Electronics Lab
3 Computer Lab
6 Electronics Lab
8 Computer Lab
B-H curve of soft ion & material on board with power supply,
39 2
Ferrite of any one type. ammeter, flux meter
Transformers –E, I, L
laminations, auto, different transformer - step down 230v/24v
43 5
power center tap & step up 230v v
voltage measurement .
Manufacturing of SS
53 Manufacturing process, itching material 5
& DS PCB.
soldering gun with soldering materials for
54 Soldering gun 5
design & analysis
Resistors,capacitors,
Different ckts using active, passive
55 inductor, transistors 5
components with power supply meters
mounted on PCB
Active integrator using Practical set up for Active integrator using 741
72 5
741 as inverting type with +/- 10V power supply
DAC Interface
(Generation of square, Microprocessor 8085 practical kit) containing 8085 practical
25 10
triangular and staircase 8255 IC, required FRC connector kit
waveform (using 8255)
Amplitude modulation
Experimental kits,230v,50Hz signal generator
32 using Emitter 3
IFT(100KH)
Modulator.
Amplitude modulation
Experimental kits,230v,50Hz signal generator
33 using Collector 3
IFT(100KH)
Modulator.
Amplitude
34 Demodulation using Experimental kits,230v,50Hz AM generator 3
Simple Diode detector.
Amplitude
35 Demodulation using Experimental kits,230v, 50Hz AM generator 3
Diode
36 Detector( AGC ). Experimental kits,230v, 50Hz AM generator 3
Frequency Modulation
37 T=BF 494 D=DA102B vector diode 3
using IC 8038.
Frequency
38 demodulation using T=BF 494 D=DA102B vector diode 3
Ratio Detector ,
Phase shift
39 Experimental kit 3
discriminator.
Frequency shift keyed
40 modulation and IC555 experimental kit 3
demodulation.
Phase shift keyed
41 modulation and Experimental kit 3
demodulation.
Pulse Amplitude
42 Modulation and Experimental klit 3
Demodulation
Pulse Width
43 Modulation and Experimental kit 3
Demodulation.
Pulse Position
44 Modulation and Experimental kit 3
Demodulation.
Pulse Code
45 Modulation and Experimental kit 3
Demodulation.
MODEM with
46 Experimental kit 3
demonstration .
Fault finding in a Black
and White T.V.
47 Receiver using voltage Black & White TV with experiment kits 1
analysis and signal
flow testing.
Fault finding in a
Colour T.V. Receiver
48 Colour TV with experimental kits 1
using voltage.analysis
and signal flow testing
Characteristics of Two
49 core and coaxial Experimental kit 1
transmission lines .
Characteristics of
50 Experimental kit 1
optical fibre cable.
Operation of a Mobile
52 Experimental kit 1
phone.
Operation of a FAX
53 Experimental kit 1
machine.
ANNEXURE I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
Proportional controller-
Electronic proportional action circuit
P+I controller.
12 provision to change PB set point integral time, 2
P+D controller. derivative time, heater, control valve
PID controller.
Potentiometer
characteristic & Two pairs of potentiometer with knob to move
13 2
Potentiometer as error wiper provision to measure output
detector
Synchro transmitter
14 Pair of synchro provision to measure output 2
characteristic
Permanent magnet / variable type reluctance
15 Stepper motor motor provision to measure speed and 2
direction
A.C. position control
16 Provision to transmit position 1
system
D.C. position control
17 Provision to transmit position 1
system.
18 AC tachometer motor load 3 & half digit display 1
19 DC tachometer motor load 3 & half digit display 1
Milliamp input with milli-ammeter load
20 Amplidyne. 1
200watt bulb 0-400 Watt meter
Separate manual
Practical kit for temperature control system of
shouldbe
Feedback control range 0 to 100 centigrade with relay based
21 1 provided for SR
system heater and fan control (using ON/OFF
no 1 to 12 per
concept)
quantity
Verification of
Experimental kit with power supply,
1 Kirchoff’s voltage law 5
voltmeter, current-meter, rheostat
by mesh analysis
Verification of
Experimental kit with power supply, voltmeter
2 Kirchoff’s current law 5
Experimental kit, current-meter, rheostat
by node analysis
Verification of
Experiment kit with power supply ,
4 maximum power 5
voltmeter, current-meter ,rheostat
transfer Theorem
Verification of Experimental kit with power supply
5 5
Norton’s Theorem voltmeter, current-meter rheostat
Charging and
Experimental kit with capacitor DC power
6 discharging of C 5
supply & voltmeter ICTP switch, ammeter
through R
Practical kit to plot
Experimental setup with magnetic material
7 magnetization curve of 5
with power supply, ammeter, flux-meter
magnetic material,
Demonstration kit of
Experimental kit with Coil ,ammeter and
8 Fleming’s Left Hand 5
voltmeter
Rule.
Practical setup for
Experimental setup with Coil ,power supply,
9 demonstration of 5
ammeter and voltmeter
Faraday’s Law
Practical setup to plot
10 rise & decay of current RL Circuit with supply, voltmeter, ammeter 5
in R-L circuit
Measurement of power
17 in inductive circuit by 3 wattmeter on board with supply 2
voltmeter method
Practocal setup to
1phase 230v,5amp 1kV with AC
determine voltage ratio,
18 voltemeter,ammeter,1phase autotransformer 2
current ratio of
with ICDP switch
transformer.
Practical kit to
1phase 230v,5amp 1kV with AC
determine efficiency &
19 voltemeter,ammeter,1phase autotransformer 2
regulation by load test
with ICDP switch
on transformer
20 Auto transformer 1kv max. voltage to primary 230v, 5amp 2
kilowatt/hp-1.5,220v,exitation 220v,6.5amp
21 D.C. machine 2
wdg-shunt
Setup to determine Kilowatt/hp-1.5,220v,exitation 220v,6.5amp
22 brake test on D.C. wdg-shunt lamp load, tachometer, rheostat 2
shunt motor. with meters
Kilowatt/hp-1.5,220v,exitation 220v,6.5amp
D.C. shunt motor setup
23 wdg-shunt lamp load, tachometer, rheostat 2
to determine speed test
with meters
24 3 point starter Rotor resistance starter 3 phase, 5hp- 415v 5
3kv,415v,3 phase , 6amp,50Hz,1440rpm slip
25 3 ph I.M. 2
ring IM
Practical setup to
observe reversal of 3kv,415v,3 phase , 6amp,50Hz,1440rpm slip
26 2
rotation of 3 ph I.M. ring IM with tachometer and meters
and to find no load slip
Practical setup to
27 observe 1 ph I.M. and 0.37kvwatt,230v, squirrel cage IM 2
identify their parts
SC Ron board with power supply 0-300vDC, 0
Practical kit for V-I
28 30vDC & voltmeter 0-200v, ammeter 0- 2
characteristics of SCR
100mA
Practical kit for V-I DIA Con board with power supply 0-30vDC
29 2
characteristics of DIAC & voltmeter 0-200v, ammeter 0-100mA
Practical kit for V-I TRIA Con board with power supply 0-
30 characteristics of 300vDC, 0-30vDC & voltmeter 0-200v, 2
TRIAC ammeter 0-100mA
Using diodes with 3phase transformer as a
31 3-phase rectifier. 2
resistive load
SCR control circuits using gate triggering
32 Phase control of SCR 2
circuit
Practical kit for Step
using SCR with gate triggering as a DC
33 up & step down SCR 2
supply0-100v
choppers
using SCR with gate triggering as a DC
34 SCR Series inverter. supply0-30v, AC output 180v, 1.5KHz to 2
3kHz
Using SCR with gate triggering as a DC
35 SCR Parallel inverter. supply0-18v, AC output 175v,peak sq. wave, 2
60watt,400Hz
Relay type input voltage 180-250vAC, output
Relay type/ servo type voltage 210-230v
36 2
stabilizer Servo type input voltage 180-260 vAC, output
voltage 230-237v
Practical kit for TRIAC Using TRIAC with gate triggering & AC 230v
37 2
as a switch. source
Minimum
Sr Name of
Technical Specifications Qty. / Nos Remarks if any
No. Equpt./Machinery
Required
MECHANICAL ENGINEERING
(ME)
3 Theory of Machine 5
6 Fluid Power 11
7 Automation 13
8 Production 15
3 Theory of Machine 20
6 Fluid Power 23
7 Automation 24
8 Production 25
ANNEXURE - I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERY
(Essential equipment/ Hand Tools)
(Required for conducting thePractical)
1. Name of course/ Department:- Mechanical Engg. Dept.
2.Name of laboratory : Power Engineering
Minimum
Remark if
Sr. No. Name of Equipt./Machinery Technical Specifications Qtty./Nos.
any
Required
1 An experiment set up on solar flat 0 1
100 litre, 60 C
plate collector used for water heating
24 Solar water heating system test rig Heating water of capacity - 100 1
Litres with single cover Flat
plate collector size 3feet X 3feet
DIPLOMA IN MEDICAL
ELECTRONICS
(MU)
(AICTE Approved Course)
INDEX
Sr.No. Essential Equipments Labwise Page No.
1 Medical Electronics 1
2 Electronic 7
Name of Minimum
Sr. Remark
Equipt./ Technical Specifications Qtty./Nos.
No. if any.
Machinery Required
Deflection Coefficient (CH1 & CH2)-1mV/div to 20V/div.
5mV/div to 20V/div in 12 calibrated steps in 1-2-5 sequence.
x5 Magnification increases the sensitivity to 1mV/div & 2mV/div
(LEDindicated)., Accuracy-±3%. Bandwidth DC - 30MHz (-3dB), dc
coupled
10Hz - 30MHz (-3dB), ac coupled., Rise Time- 11.6ns or less.Display
Modes CH1 only, CH1 & CH2 alternate or chop mode, Algebraic addition
CH1+CH2, Algebraic subtraction CH1-CH2, CH2 invert & X-Y.-Input
Impedance 1M ohms // 25pF (approx).,Maximum Input Voltage 400V (DC
+ AC peak). Internal Trigger Signal CH1 or CH2 signal.
TIME BASE
Sweep Speed 18 calibrated steps. 0.5µs/div to 0.2s/div in 1, 2 & 5 sequence.
Sweep Magnifier x5 Magnification extends the sweep speed to 100ns/div.
x5 Magnification indication wtih LED. ,Accuracy ±3%. Variable
Uncalibrated continuously variable control between steps, extends fastest
sweep speed to 40ns/div (approx) (Uncal LED indication). Hold-off Time
4:1 (approx.) variable control.
Triggering Mode Automatic or Normal with Level Control.
Source CH1 / CH2 / LINE / EXT. Slope Positive or Negative.
Coupling ac / dc / HF reject or TV-V / TV-H., Trigger Sensitivity
Internal : AUTO 1 div 30Hz - 30MHz
NORM 1 div 3Hz - 30MHz. External : AUTO 1V p-p 30Hz - 30MHz
5 In 1 Test NORM 1V p-p 3Hz - 30MHz (Typical 40MHz at 2 div).
1 1
Lab HORIZONTAL DEFLECTION Horizontal input via CH2
(CH1 operates as Y). Deflection Coefficient Same as CH2.,
Bandwidth DC - 1MHz (-3dB). Input Impedance 1M ohms and
25pF (approx).
GENERAL
Cathode Ray Tube 140mm Rectangular Screen, Internal Graticule 8 x 10 cm,
P31 Phosphor. Accelerating potential : 2kV.
Trace Rotation Front Panel Control, allows ±5º of trace adjustment.
Z Modulation 30V p-p signal upto 1MHz modulates at normal intensity.,
Calibrator Provides 0.2V ±2%, 1KHz squarewave output for probe
compensation. DUAL COMPONENT TESTER/COMPARATOR Dual
Component Tester allows comparison of a Device-Under-Test (D.U.T.)
and a sample device. Test Voltage 8.6V rms.
Test Current 28mA max.
Test Frequency 50Hz or 60Hz.
TRIPLE OUTPUT D.C. SOURCE Three independent, regulated
DC outputs, +5V at 1A max and ±12V at 200mA max. continuous
(common floating w.r.t. ground).
Line / Load Regulation ±2%.,-Ripple Less than 8mV r.m.s.
Termination 2mm Jacks on the Front Panel.
Frequency Range 0.02Hz to 2MHz in 8 decade ranges.,Output Waveform
DC, sine, triangle, square.
DC Offset ±5V (across 50 ohms), ±10V (open circuit).
0.02Hz - Maximum Output Voltage 10V p-p for all functions (with 50 ohms loads).
2MHz 20V p-p open circuit (DC + AC peak not exceed 10V across 50 ohms). ,
FUNCTIO Output Impedance 50 ohms (nominal).
2 1
N Attenuator 0dB to 40dB in steps of 20dB, 20dB fine attenuation by
GENERAT amplitude control.
OR Accuracy ±0.5dB per 20dB step at 1KHz.
Sine Distortion Less than 3% upto 200KHz.,
Two Channel,
Bandwidth: DC- 30MHz (-3dB), No. of ,Channels: Two Channels
Trigger system: Automatic & normal (level
adjustable)
Sensitivity: Internal 0.5 Div External 0.5 V,
Trigger Bandwidth: 40MHz
CRO-
Max. Input voltage: 300 Vrms, Component
4 30MHz 1
Tester: Built in single touch
Analog
Continuity Tester: With Beeper ,
Accessories: Two 1X/10X Switchable
probes per channel, BNC-BNC Cable,
Power Cord, Manual, Calibration
Certificates.
1. 4 ½ Digits, better than 20,000 Count display ,1. 4 ½ Digits, better than
20,000 Count display, 2. Large LCD display 3. New style bar graph display
based on binary bit expression. 4. Peak detection mode for high speed
signal capture 5. Auto calibration 6. 50MHz frequency counter
7. True RMS for AC or AC + DC mode 8. Dual Display for frequency, 9.
Digital AC voltage & temperature 10. 10 Location Memory 11. Time mode with
Multimeter- alarm, clock and stop watch 12. MIN, MAX, AVG and relative mode 13.
5 1
(portable or Decibel measurement 14. Capacitance and inductance measurement 15.
handheld ) Pulse signal injection function for logic & audible testing, etc. 16.
Continuity and diode test 17. Logic test 18. Auto Power off and "keep on"
mode 19. Fused 20 A input with warning beeper 20. Back light 21. Data
hold and run mode 22. Low Battery indication mode 23. Overload
protection 24. Certified by competent authority
Features
• Wide Frequency Range from 1Hz to 1MHz • Low Harmonic Distortion for
Sine Wave • Sine and Square Wave Outputs • Use of Thermistor provides
Higher AVC Gain and Flat Frequency Response • Better Frequency
Stability • Built-in Attenuator upto 60dB in 20, 40, 60 dB steps • Maximum
Sine Wave Output of 30V p-p • Maximum Square Wave Output of 20V p-p
• Rise and Fall Time <100ns Compact and Portable • Digital Readout of
Frequency • Ext Counter Facility,Frequency Range 1Hz to 1MHz in 6
decade ranges. 1Hz to 10Hz, 10Hz to 100Hz, 100Hz to 1KHz, 1KHz to
10KHz, 10KHz to 100KHz, 100KHz to 1MHz.,Frequency Indication 4 digit
0.3" LED display. Frequency Accuracy ±0.1% of reading ±1 count. Max.
Output Voltage at 1KHz Sine : 10V rms ±1V rms. Square : 20V p-p or
above.,Attenuator 4 steps corresponding to 0dB, 20dB, 40dB, 60dB.
1MHz Accuracy within ±1dB at 1KHz. Attenuator Output Impedance 600 ohms
SINE/SQU ±5% (at 20dB, 40dB, 60dB attenuation). Amplitude Change with Frequency
ARE For sine wave (checked at 10V rms w.r.t. 1KHz)., 1Hz to 1MHz : ±1.0dB.
11 1
GENERAT Sine Wave Distortion <0.05% in the range from 400Hz to 20KHz. <0.2% in t
OR/COUN range from 200Hz to 40KHz., <0.4% in the range from 40Hz to 100KHz,
TER <1.5% in the range from 10Hz to 300KHz.Rise and Fall Time
(Square Wave) <100ns.,Ext. Frequency Counter Frequency Range
1Hz to 1MHz. Input Amplitude 1V to 50V p-p. Accuracy ±0.1% of
reading ±1 count.Resolution Autoranging, depends on input frequency.
1Hz to 9.999KHz - 1Hz., 10KHz to 99.99KHz - 10Hz.,
100KHz to 999.9KHz - 100Hz., >999.9KHz - 1KHz. Power 230V
AC ±10%, 47-53Hz. Optional 115V AC ±10%, 57-63Hz. Dimensions
270 (W) x 88 (H) x 310 (D) mm. Weight 3 Kg. (approx.). Standard
Accessories 1. Instruction Manual - 1 No. 2. BNC (M) to Alligator
Clip - 1 No. 3. Mains Cord - 1 No
I (a) Rated KVA : 2 KVA I (b) Rated Input Voltage :a) Single Phase 160-
260V b) Three Phase 280-450V I (c) Frequency : 50 Hz II) Number of
phase : Single/Three Phase III) Rated output Voltage :a) Single Phase
240V b) Three Phase 415V IV) Rated output Current : 4.17 Amp./KVA
per phase V) Rated Voltage Correction Rate : As per IS:9815 (Part-I/1994)
VI) Losses at reference temperature 75oC a) No load loss at minimum
rated input voltage. : Less than 1.5% of the rated capacity. b) No load loss
at maximum rated input voltage : Less than 1.5% of the rated capacity. c)
Full load loss at minimum rated input voltage. : Less than 4.5% of the rated
capacity. d) Full load loss at maximum rated input voltage : Less than 4.5%
of the rated capacity. e) Maximum load loss and input voltage at which it.
occurs: Less than 4.5% of the rated capacity at input voltage 180V, f) Rated
efficiency : More than 95% VII) Type of Cooling a) Air Cooled : 1 KVA
TO 10 KVA (SINGLE PHASE) : 3 X 1 KVA TO 3 X 10 KVA (THREE
HASE) b) Air/Oil cooled : 16KVA and 3 X 16KVA c) Oil Cooled : 20 K
TO 300 KVA (SINGLE PHASE): 3 x 20 KVA TO 3 x 350 KVA
(THREE PHASE) Note: 1. Oil Cooled Servo Motor Operated Line
SERVOST Voltage Correctors will be supplied without first filling of Transformer oil. 2
12 1
ABILISER Oil will be used having ISI marked or strictly conforming to IS:335/1993
with latest amendments. VIII) Class of Insulation a) Air Cooled -
B Class b) Oil Cooled - A Class IX) Particulars of Servo Motor
a) Number of Servo Motors : One in single phase Three in Three
phase b) Rated torque : 3 Kg-cm upto 25 KVA / 3 x 25 KVA, 10 kg-cm
on ad above 31.5 KVA / 3 x 31.5 KVA Upto 150 KVA &
3 x 150 KVA and 20 kg- cm on & above 200 KVA & 3x 200 KVA
c) Rated Voltage : ---- 230/240 Volt, AC--- d) Rated Watts : Less
than 35W for 3 Kg-Cm Servo Motor Less than 60W for 10 kg-cm
Servo Motor Less than 100W for 20 Kg- cm Servo Motor e) Type of
supply : -----Single Phase AC, 50 Hz----- X) Particulars of variable
auto transformer a) Type and grade of the core : As per relevant ISS
b) Size and weight of the core : As per relevant ISS c) Size and
total weight of the windings : As per relevant ISS d) Size type
and grade of the copper wire used. : As per relevant ISS
4 Bit
Brinary
13 Counter 1
(Ripple
Counter
4 Bit
Brinary
14 Counter 1
(Ripple
Counter
Light
15 Operated 1
Relay
Characterist
16 ics of 1
Photodiode
Characterist
17 ics of 1
Photodiode
Wein
18 Bridge 1
Oscillator
UJT
19 Relaxation 1
Ocillator The trainer kit should be ready to connect 230 volt.50 hz supply .The o/p
Tuned RF should only need o/p devices such as CRO.The kit should be prefersbly
20 Amplifire 1
transperent.
UJT
21 Relaxation 1
Ocillator
Burglar
22 Alarm 1
R/S -Filp
23 Flop 1
OP-AMP
24 Parameters 1
Part II
OP-AMP
25 Parameters 1
Part II
Ring
26 1
Counter
Basic Logic
27 Gates using 1
Diode
&Transistor
I
R/S -Filp
28 1
Flop
Ring
29 1
Counter
Basic Logic
30 Gates using 1
Diode
&Transistor
I
Digital
31 Logic 1
Trainer
Study of DE
32 1
- Morgans
theorems
Study of DE
33 1
- Morgans
theorems
M-S/J-K
34 1
Flip Flop
M-S/J-K
35 1
Flip Flop
Tuned RF The trainer kit should be ready to connect 230 volt.50 hz supply .The o/p
36 Amplifire should only need o/p devices such as CRO.The kit should be prefersbly 1
using FET transperent.
37 Characterist 1
ics of UJT
Hartley
38 1
Oscillator
Hartley
39 1
Oscillator
Negative
40 Feedback 1
Amplifier
41 Characterist 1
ics of UJT
Negative
42 Feedback 1
Amplifier
Audio
Amplifier
43 1
using IC
810
Audio
Amplifier
44 1
using IC
810
OP-AMP
45 Parameters 1
Part I
M-S/J-K
46 1
Flip Flop
M-S/J-K
47 1
Flip Flop
OP-AMP
48 Parameters 1
Part I
Regulater
P/S using
49 Transistar 1
(Series
Type)
Regulater
P/S using
50 Transistar 1
(Series
Type)
Voltage
Comparatar
51 1
using IC
710
Voltage The trainer kit should be ready to connect 230 volt.50 hz supply .The o/p
Comparatar
52 should only need o/p devices such as CRO.The kit should be prefersbly 1
using IC
710 transperent.
OP-AMP
53 AS Log 1
Amplifier
54 Phase Shift 1
Oscillator
2206 AS
55 Wave form 1
Generator
Instrum
entation
56 1
Amplifier
LM 321
OP-AMP
57 AS Log 1
Amplifier
Decade
58 1
Counter
OP-AMP
59 AS AUDIO 1
Amplifier
2206 AS
60 Wave form 1
Generator
61 Basic Logic 1
Gates
OP-AMP
AS Voltage
62 1
to
Converter
OP-AMP
AS Voltage
63 1
to
Converter
64 Phase Shift 1
Oscillator
OP-AMP
65 AS Log 1
Amplifier
Instrum
66 entation 1
Amplifier
BASIC
67 LOGIC 1
GATES The trainer kit should be ready to connect 230 volt.50 hz supply .The o/p
BASIC
should only need o/p devices such as CRO.The kit should be prefersbly
68 LOGIC 1
GATES transperent.
Characterist
69 ics of Photo 1
diode
Transistar
Characterist
70 ics of Photo 1
diode
Transistar
4 bit
Asynchrono
71 us 1
UP/DOWN
Counter
Decade
72 1
Counter
Regulater
Power
73 Supply 1
using IC
317
Annexure- II
MSBTE NORMS AND STANDATDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Desired Equipment / Hand Tools)
(Required for contucting The Practicals.)
PRODUCTION ENGINEERING(PG)
AND
PRODUCTION TECHNOLOGY(PT)
(AICTE Approved Course)
Page 1
INDEX
2 Heat Engineering 2
3 CAD/CAM 3
7 Heat Engineering 7
8 CAD/CAM 8
Page 2
ANNEXTURE-1
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
Page 3
ANNEXTURE-1
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
Page 4
ANNEXTURE-1
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
Page 5
ANNEXTURE-1
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
Page 6
ANNEXTURE-1
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
Page 7
ANNEXTURE-II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
Page 8
ANNEXTURE-II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
Page 9
ANNEXTURE-II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
Page 10
ANNEXTURE-II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
No Desired Equipments
Page 11
ANNEXTURE-II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
Page 12
MAHARASHTRA STATE BOARD OF
TECHNICAL EDUCATION, MUMBAI
Workshop Technology
(Mechanical Group)
(WS)
HUMANITIES
(HS)
PHYSICS, CHEMISTRY &
COMMUNICATION SKILLS
(AICTE Approved Course)
INDEX
2 Physics 4
3 English 6
5 Physics 8
6 English 9
ANNEXURE –I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERY (Essential Equipment / Hand Tools )
(Required For Conducting The Practicals )
Minimum Qtty.
Sr. No. Name of Equipment /Machinery Technical Specification Remark if any
Nos. required
Table Model PH
Range 0 to 14.00 Mv
0 to ± 1999 Resolution PH
0.01 Mv 1. Accuracy
PH ± 0.01 Mv± 1
Tempeture auto 0 to 100°C.
Compensation manual 0
Digital PH Meter OR
1 to 100°C. Space 1
Microprocer based PH Meter
correction 80 to 120 %.
Display 3 & half Digit LED.
Power 230V± 10%.
Accessories combination - PH
electrode. buffer tablet 4PH to
7PH, operation manual,
Eletrode stand, Dust cover .
0 to 60 min. 0
3 Stop Clock 2
to 60 second Table model .
3
Capacity 300gm Readability
0.001gm. Repeatability
0.001gm, linearity 0.002gm.
Response time 2-3 Sec. Power
4 Weighing balance supply A/C,adopter 230V, 1
50Hz, larger backlight
graphical LCD display.
Automatic calibration
weighing units like gm,mgm.
4
17 De ioniser plant 100 litres/hour 1
Size 9"x4"x4" , Temp max
1000°C/1200°C. Coorking
temp 930°C to 1130°C. Digital
18 Muffle furnace 1
temperatur indicator mm
controller . Power supply 230V
AC
25 x 30 cm May
temperature 300°C , 1500
19 Hot Plate 1
watts, Body made of M.S,
Powr suppply 230V Ac
250 ml Spun
jointles, Aluminium, Max.
20 Heavy Mantle 1
Temp. 400°C, Temp cotroller
with regulater
06 hole
constant temprature Made of
SS Temp. range from ambient
21 Water bath to 100°C and Temp. control by 1
digital temp. indicator cum
controller with accuracy +
0 .5°C
5
ANNEXURE –I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERY (Essential Equipment / Hand Tools
(Required For Conducting The Practicals )
Minimum Qtty.
Sr. No. Name of Equipment /Machinery Technical Specification Remark if any
Nos. required
1 Pullingers apparatus ISI mark of 1 meter length rod 2 sets
2 o.5 mw - He- Ne - Laser 0.5mw 2 sets
3 Optical bench Laser pens Scale Standard 2 sets
4 Avaccum photo electrical cell Standard 2 sets
5 Solar panel Ge - Si - panel 2 sets
6 Voltmenter 0 - 10 Volt rang 2 sets
7 Regulated power Supply 0 to 10 V d c 3 sets
8 Milliammeter 10 to 200 m.a. 3 sets
9 Rheostat 15 to 50 ohm 3 sets
10 Bulb 40 Watt 3 sets
11 Colour Filters Standard 3 sets
12 Various Capacitors 10 micro Farad 3 sets
'' 100 '' 3 sets
'' 1000 '' 3 sets
13 Capacitance meter Digital 3 sets
14 Power Supply 0 to 10 V - dc 3 sets
15 Wires Insulated Copper wires 3 Boundle
16 Glass Slabs 10cm x10cm Size 3 sets
17 Electric Bulb 60 Watt 3 sets
18 Thermistors I S I marked 3 sets
19 Thermometers 0 -100 C 3 sets
20 micro-ammeter 0- 100 micro ampere 3 sets
21 Tap Keys Standard 3 sets
22 Air Capacitor ISI mark 3 sets
23 Pico Faradmeter Standard 3 sets
24 Wax Standard 1/2 Kg.
25 Sets of Springs Standard 3 sets
26 Slotted weights 50gm,500gm 3 sets
27 Hangers Standard 3 sets
28 Stop watch ISI mark 3 sets
29 Sodium lamp with choke Standard 3 sets
30 Mercury lamp ISI mark 3 sets
31 Newtons ring apparatus ISI mark 3 sets
32 Glass Plates Standard 3 sets
33 Double Conven lens ISI mark 3 sets
34 Somometer apparatus Standard 3 sets
35 Sets of tuning forks with 288Hz 512 Hz 3 sets
Rubber pad 334 Hz 600 Hz
36 Travelling microscope ISI mark 3 sets
6
ANNEXURE –I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERY (Essential Equipment / Hand Tools
(Required For Conducting The Practicals )
Minimum Qtty.
Sr. No. Name of Equipment /Machinery Technical Specification Remark if any
Nos. required
NIL NIL NIL
7
ANNEXURE –II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERY ((Desired Equipment / Hand Tools )
(Optional Equipement )
Minimum Qtty.
Sr. No. Name of Equipment /Machinery Technical Specification Remark if any
Nos. required
1 NIL NIL NIL
8
ANNEXURE –II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERY ((Desired Equipment / Hand Tools )
(Optional Equipement )
Minimum Qtty.
Sr. No. Name of Equipment /Machinery Technical Specification Remark if any
Nos. required
1 NIL NIL NIL
9
ANNEXURE –II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERY ((Desired Equipment / Hand Tools )
(Optional Equipement )
Minimum Qtty.
Sr. No. Name of Equipment /Machinery Technical Specification Remark if any
Nos. required
PIV Dual care with latest
configuration and multimedia,
1 Computers LAN,Sound Card etc. 20+1 20 Students-1 Teacher
PIV Dual care with IGB Ram ,
multimedia LAN Card & latest
2 Server configuration
Multisensory learning , Play
back of recorded Audio
cassettes/CD facility to have
Digital Multimedia Language Lab group discussions, facility to
software Monitor students Computers,
facility to control students
computers Key boards and
3 mouse Renet
4 Networking Switch cabling etc.
CLARITY
Software Related to english
5 English Software
6 Study material for English Related to subject
10
MAHARASHTRA STATE BOARD OF
TECHNICAL EDUCATION, MUMBAI
1 Shoe Bottming 1
3 Quality Control 5
4 Footwear Designing 6
NO DESIRED EQUIPMENT
ANNEXURE-I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT AND MACHINERIES ( Essential Equipment/Hand Tools)
Name of Minimum
Sr.No. Technical Specification Remark
Equpt./Machinery Qtty Reqd
Cutting Table - 1600 X 500 mm
Trolley - 500 X 500 mm
1 Beam Cutter 1
Pressure - 25 T
Power - 2 H.P./1.47 kW
Dimension - 890X1450X2000 mm
Air Consumption at 6 bar - 87Lt/min
Back part Moulding
2 Electrical Consumption - 2.7 KW 1
Machine
Weight- 620kgs
Production - 1300pairs/8hrs
Dimension - 680X830X12000 mm
N.W. - 70 kg
Working Temperature - +200°C
3 Vamp Conditioner 1
Thermo - 0-100%
Air Consumption - 25KL / 4KW
Production - 1000pairs/8hrs
Dimension- 1600x1150x1850 mm
Temperature of Heat Adhesive - 210-230°C
Power consumption - 2.1kw
4 Toe Lasting Machine 2
Air consumption - 446 NL
N.W. - 954 kg
Production - 2000 pairs/8hrs
Power- Max. power watt 3.100
Dimension - 11.5x85x150
Weight- 600 kgs
Heel Seat Lasting Production capacity- 300 pairs
5 1
Machine Automatic Operating Divce- Electric &
Hydrolic
Special Attachment of applying Neoprene or
Thermo plastic cement
Dimension - 650x500x1300 mm
Voltage - 380V
6 Pounding Machine 1
Power - 1.5 HP
Production - 3000Pairs8hrs
Dimension - 3500x950x1540 mm
Voltage - 380V
7 Heat setter Air presure - 0.5 Mpa 1
Power - 17.2 kw
Production - 2000Pairs8hrs
Roughening Machine 2 HP motor with blower fan
8 with 2
Power- 1.5 kw
Dust Collector
Dimension - 3000x1000x1324 mm
Power - 15KW
9 Heat Activator Voltage - 380V 1
Air Pressure - 5bar
Production - 1200 pairs/8 hrs
Station - Two station R/L
Width - 81 cm
Dept - 88 cm
10 Sole Attaching Machine 1
Height - 140 cm
Net weight - 305 kg
Compressor - 100 ltr.
No.of Cylinder - One
Displacement - 310 Ur/min
Capacity - 100 ltr.
Maximum working - 12.5 kg/ cm2
Spray booth with
11 Motor - Three phase 1
Compressor
H.P. - 3.7
RPM - 1430
Working Dimension - 1525 mmx
1220x2100mm
ANNEXURE-I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT AND MACHINERIES ( Essential Equipment/Hand Tools)
Minimum
Name of
Sr.No. Technical Specification Qtty Reqd Remark
Equpt./Machinery
Cutting table - 900 x 430 mm
Swing Arm Cliking Arm width - 370 mm
1 1
Machine Pressure - 20 T
Power - 1 HP/0.75 Kw
Production - 2000 pairs/8hrs.
Maximum spliting width - 420 mm
2 Splitting Machine 1
Voltage - 380 V
Power - 2.7 KW.
Size - 520x420mm
Motor - .75 HP
Power- Three phase
3 Skiving Machine 2
Roller gear,Clutch motor, Exhaustor,Bell
Knife
Anti dust protection guard
Size - 1170 x 530x1110 mm
Weight - 89 KG
4 Edge Folding Machine 1
Edge Folding width - 3 mm to 6.5mm
Power - 1 HP
Singal Needle Zig-Zag lock Stich
Bottom feed
Horizontal hook
5 Zig-Zag Machine Swing foot lift automatic 1
Speed - 2200 SP
Needle - 134 R
Voltagte - 0.8 KVA
Maximum Stich length - 4.5 mm
Maximum Swing spped - 4200 stich per min.
Flat Bed Single Needle Needle - 134 R ( 90,100,110)
6 2
Machine Needle Distance - 2 to 40 mm
Thickness of Swing material - upto 6 mm
Machine drive -Electric moto .4 KW
Maximum Stich length - 4.5 mm
Maximum Swing spped - 4200 stich per min.
Flat Bed Double Needle Needle - 134 R ( 90,100,110)
7 1
Machine Needle Distance - 2 to 40 mm
Thickness of Swing material - upto 6 mm
Machine drive -Electric moto .4 KW
Maximum Stich length - 4.5 mm
Maximum Swing spped - 4200 stich per min.
Post Bed Single Needle Needle - 134 R ( 90,100,110)
8 2
Machine Needle Distance - 2 to 40 mm
Thickness of Swing material - upto 6 mm
Machine drive -Electric moto .4 KW
Maximum Stich length - 4.5 mm
Maximum Swing spped - 4200 stich per min.
Post Bed Double Needle Needle - 134 R ( 90,100,110)
9 1
Machine Needle Distance - 2 to 40 mm
Thickness of Swing material - upto 6 mm
Machine drive -Electric moto .4 KW
Maximum Stich length - 4.5 mm
Maximum Swing spped - 4200 stich per min.
Cylinder Bed Sewing Needle - 134 R ( 90,100,110)
10 1
Machine Needle Distance - 2 to 40 mm
Thickness of Swing material - upto 6 mm
Machine drive -Electric moto .4 KW
Accommodate Eyelets - 3 to 12 mm
Head - Strong steel construction
Punching & Eyeleting
11 Hooper - Easly replace 1
Machine
Electricity - Three phase motor
Special attachment for bigger Eyelets
Voltage 220V (3 Phase)
Size of hot plate- 200x260 mm
Size of base plate- 320 x 360 mm
12 Stamping Machine Max. Pressure - 2000 kg
Temperature controller - 0- 400°c
Max. gap - 250 mm
Max. stroke of hot plate - 120 mm
ANNEXURE-I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT AND MACHINERIES ( Essential Equipment/Hand Tools)
Name of Minimum
Sr.No. Technical Specification Remark
Equpt./Machinery Qtty Reqd
Felt pad - 25:4 mm , 6.35 mm thick
Load on felt - 0.73 kg or 2.3 kg
1 Rub Proofness tester 1
Pot speed - 150 rev/min
Counter - 5 digit stroke counter
Rotation of Wheel- 75 R.P.M.
Distance between axix of rotation
and axis of bottoles - 67 mm
Water Vapour
No. of Bottoles - 6Nos.
2 Permieability 1
Inner dia of bottele- 30 mm
Tester
Rotation of fan- 1425 rpm
Size of blade - 75 mm
Motor - 1/4 h.P. 200 volt AC
Angle of Ascilation of grips - 221±2°
Flexing frequency - 100 ± 5 cycles/min
3 Flexometer 1
Size of test specimon- 70x45 mm
Motor - 1/4 HP single Phase 222V AC
Flexing frequency - 60 cycles/min
4 Shoe Flex Tester Max. angle of flexing of shoe - 30° 1
Motor - 1/4 H.P. 220 single phase.
load- 1-15 kg
5 Tensile Tester Power- 0.75 H.P.
Attached Printer with Whole unit
Attached with hot plate with stritter
6 Shrinking Temp 1
Temp. should show 60°c to 150°c
Digital meter with the whole unit
7 Lastometer
loade - 1-6 kg.
ANNEXURE-I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
Name of Minimum
Sr.No Technical Specification Remark
Equpt./Machinery Qty Reqd
1 Monitor Samsung /LG LCD 15"/17" 10
DVD Writer - 18X
CPU -3.4 GHZ
Mouse - Optical
Keyboard - Multimedia
2 CPU 10
Ram - 1GB
UPS - APC 500/1000
Web cam - 640 pixel
HDD - 120 Gb/ 160Gb
3 Printer Laser 1
4 Scanner HP 2400/4370 1
Dimensions - 2D/3D-CAD system
Product - CAM Software
Procost Pre Costing System
Shoe Desigining
5 Universal Converter-Universal File converter 1
(CAD) Softwear
DCS- CAM Software for cutting-painting
systems&layout
Dimension - 18" x20"
6 Digitizer Power - 12 X DC 1
Digitizar ( Mouse 1)
Speed - Up to 900 mm/s
Max.Cutting dept- < 2mm
Material of Cutting - All kind of hard
cardboard
& Plastic board, fibrous cardboard etc.
Drawing tool - Multi-functional set, 8 sets
of different devices including pen, half-knife
and full knife
Pens & Knifes - Ordinary signature pen,oil
pen,
7 Cutting Plotter ball pen/ Special tungsten steel knife 1
Mechanical resolution - 0.007 mm
Software resolution -
0.025mm,0.01mm,0.1mm
Buffer capacity- 128 M
Control Pannel - Liquid crystal panel
and touching bottn
Working Voltage- AC 220V +10%, 50 HZ
Motor- Step motor, Servo motor
Total measurement - 160 x 125 x 95 cm
ANNEXURE- II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
Name of Minimum
Sr.No Technical Specification Remark
Equpt./Machinery Qty Reqd
NO DESIRED EQUIPMENT
MAHARASHTRA STATE BOARD OF
TECHNICAL EDUCATION, MUMBAI
1 Leather Finishing 1
4 Quality Control 4
5 Chemistry Lab 5
NO DESIRED EQUIPMENT
ANNEXURE-I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT AND MACHINERIES ( Essential Equipment/Hand Tools)
Name Minimum
Sr.No. Technical Specification Remark
of Equpt./Machinery Qtty Reqd
Flat bottom bed
Power - 3.5 H.P
1 Glazing Machine having two Jaks 1
Working space - 3 feet
Self drive
Self drive
Power - 3.5 H.P
Working Cylinder - 2 feet
2 Bufffing Machine 1
Bufing roller - 1 feet
Dust removal unit
Adusting knob for bufing speed
Power - 4 H.P
Working Cylinder - 1 feet
3 Shaving Machine Adusting knob for working cylinder 1
Blace sharping movable arrangment
Self drive
Work width- 3200 mm
Work Speed - 7-18 m/mm
Max. work pressure- 20
Work Temprature- 180
4 Embossing Machine 1
Heat power- 24 kw
General Power- 34.8 kw
Weight - 11 ton
Dimension- 5070x2930x3050
Diameter - 400 x 400
Power - 2.2 H.P.
5 Dyeing Drum Speed (r/mm) 10 + 012 1
General Volume - 0.76 m3
Weight -1 ton
Size- 4 x 6
Indivisula drive
Processing of Power - 7.5 H.P.
6 1
Drum Wooden Power Transmittion with
reduction gear box- 1:10
Volume of drum capacity- 100 kg
Page 3
ANNEXURE-I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT AND MACHINERIES ( Essential Equipment/Hand Tools)
Name Minimum
Sr.No. Technical Specification Remark
of Equpt./Machinery Qtty Reqd
Working width- 3200 mm
Feeding speed- 0.029 (m/s)
1 Through feed Buffing General Power - 43.2 (Kw) 1
Waight (t) - 6.5
Dimension - 5220 x 2420x 1520 mm
Working width- 3000 mm
Feeding speed- 7 m/mm
Min.Mototr - 15 Kw
2 Samming Machine Hydrulic unit- 1.5kw 1
Setting cylonde - 1.5kw
Total power - 25 HP
Floor space(mm) - 4700x2500
Working width - 1200 mm
Reversible setting Weight - 30000kg
3 1
Machine Floor space- 2946x1066
Power consumtion- 1125kw
Working width- 3200 mm
Max. presure - 8 (mpa)
Vibrating staking Work speed - 4 to 12 m/min
4 1
Machine Oil pump motor- 1.5 kw
External dimension - 3850x3260x1430
Weight - 125 tone
Work width - 1300 mm
5 Dry Shaving Machine Feeding speed - 3.6-6.4 m/min 1
External dimension - 2610x1635x1870mm
No.of Spraying- 24
Automatic sparing and Work width - 340 cm
drying Feeding speed - 5-20 m/min
6 1
unit Rotary speed of spraying gun - 10-25 rpm
Tem of drying room - 60-120
Power - 48.3
Page 4
ANNEXURE-1
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT AND MACHINERIES ( Essential Equipment/Hand Tools)
Minimum
Name
Sr.No. Technical Specification Qtty Reqd Remark
of Equpt./Machinery
Working cylender width- 1800 mm
Electric Motor- T.S.H.P.
1 Unhairing Machine 1
Rubber feeding roller.
Individual drive with Vbelt
Working width- 1500 mm
Power Consumption - 13.5 kw
2 Fleshing Machine Floor space Length- 5175 1
Width - 1095
Motor Power of blade roller -55kw
Working cylinder width 0 1800m
Electric motor- 7.5 H.P.
3 Splitting Machine 1
Through feed systen
Convare blade system
Drum dia- 1000 mm
Width - 1400 mm
Leather exprimental Volume 315 lit
4 1
Drum Cupacity shaved weight- 32kg
Motor Power- 1.50 Ko
Heating power- 4.5 kw
General Volume - 10 m3
Dimetery of drum - 2000 mm
R.P.M. - 6 r/mim
5 Revolving drum Max. Motor -7.5 kw 1
Cylinder motor - 22 kw
Dimension - 4050x2800x3400
Weight - 5.5 ton
Working width of Paddle - 5 feet
Working capacity - 500kg
Paddle for Liming
6 Motor- 5 H.P. 1
& Deliming
Individual Drive RPM is 4 to 6
Depth of paddle pit - 4 feet.
Page 5
ANNEXURE-I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT AND MACHINERIES ( Essential Equipment/Hand Tools)
Name Minimum
Sr.No. Technical Specification Remark
of Equpt./Machinery Qtty Reqd
Felt pad - 25:4 mm , 6.35 mm thick
Load on felt - 0.73 kg or 2.3 kg
1 Rub Proofness tester 1
Pot speed - 150 rev/min
Counter - 5 digit stroke counter
Rotation of Wheel- 75 R.P.M.
Distance between axix of rotation
and axis of bottoles - 67 mm
Water Vapour
No. of Bottoles - 6Nos.
2 Permieability 1
Inner dia of bottele- 30 mm
Tester
Rotation of fan- 1425 rpm
Size of blade - 75 mm
Motor - 1/4 h.P. 200 volt AC
Angle of Ascilation of grips - 221±2°
Flexing frequency - 100 ± 5 cycles/min
3 Flexometer 1
Size of test specimon- 70x45 mm
Motor - 1/4 HP single Phase 222V AC
Flexing frequency - 60 cycles/min
4 Shoe Flex Tester Max. angle of flexing of shoe - 30° 1
Motor - 1/4 H.P. 220 single phase.
load- 1-15 kg
5 Tensile Tester Power- 0.75 H.P. 1
Attached Printer with Whole unit
Attached with hot plate with stritter
6 Shrinking Temp
Temp. should show 60°c to 150°c
Digital meter with the whole unit
7 Lastometer 1
loade - 1-6 kg.
Page 6
ANNEXURE-I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT AND MACHINERIES ( Essential Equipment/Hand Tools)
Name Minimum
Sr.No. Technical Specification Remark
of Equpt./Machinery Qtty Reqd
(Borocil) 2000 cc 12
(Borocil) 1000 cc 12
1 Volumetric flask (Borocil) 500 cc 25
(Borocil) 250 cc 25
(Borocil) 100 cc 25
(Borocil) 1000 cc 2
2 Measuring cylinder
(Borocil) 100 cc 25
6" dia 10
3 Funnel Glass
3" dia 25
4 Thistle funnel glass 3" dia 25
(Borocil) 5000 cc 2
(Borocil) 1000 cc 5
(Borocil) 500 cc 25
5 Conical Flask
(Borocil) 250 cc 25
(Borocil) 100 cc 25
(Borocil) 250 cc 25
(Borocil) 1000 cc 10
(Borocil) 500 cc 10
6 Beaker
(Borocil) 250 cc 25
(Borocil) 100 cc 25
7 Flat bottom flask (Borocil) 500 cc 5
8 Specific gravity bottle (Borocil) 25 cc 10
9 Weighing bottle (Tall) 50 cc 25
10 Pair of tonge brass H.P. 25
11 Tast Tube 6" x 3/4" corning 144
Test tube stand
12 for 6 test tube 25
wooden
13 Test tube holders 25
14 Test tube brush Nylon 25
15 Asbostrs sheet 6" x 6" 25
16 Porcelein tiles 6" x 6" 25
Buretle with glass
17 Borocil 50 cc 25
stoper
Borocil 25 cc 10
18 Pipette glass one mark
Borocil 10 cc 25
Page 7
Borocil 25 cc 5
19 Pipette glass measuring
Borocil 10 cc 5
Borocil 1 lb 144
20 Reagent bottles plain
Borocil 8 oze 244
21 Reagent bottle umber colBorocil 8 oze 24
22 Bottle glass wide mouth Borocil 1 lb 144
23 Blow pipe brass Q" length 25
24 Drying air cone 20
25 Kjeldahols flask Pyrox 500 cc 10
Distilation flask
26 Borocil 500 cc 10
with side tube
Distilation flask without
27 Borocil 500 cc 5
side
28 Buretle stand Iron 20
29 Buretle clamp Iron 20
30 Boss heads 20
31 Filter ring Iron 3" dia 5
32 Tripod stand 9" height 25
33 Cork pressure 1
34 Cork Borer 1
35 Horn Spoon 25
36 Desicator with lid 6" dia 25
Units of 6 heater with two sub
Kjeldhals Nitrogen
37 units 1) kjeldhls diagestion 1
estimation
2) Kjeldahls Distillation
38 Kipp's Apparatus 500 ml 1
Range 1000 - 1200 2
39 Hydrometer glass
Range 1000-2000 2
40 Thermameter 0-110°C 10
Crucible with
41 25 cc 25
lid ( silica)
Soxheel apparatus
42 500 cc 15
complete
43 Porcelein dishes 6" dia 10
44 Porcelin dishes 3" dia 25
45 PH tester 1
Page 8
Bunsons burnor
46 20
with pilot flame
47 Analetical Balance 10
48 Watch glass 3" dia 25
Distillation water
49 1
apparaturs
Air over electrical
50 1
control
Proctors Tanning
51 Extractor 10
Apparaturs
52 Kotch extractor 5
53 Muffle furnace 1
54 Flame protector Galvanised 20
Water bath
55 with 8 bath 1
electrically heated
56 Visoo meter college pattern 5
Wash bottle with
57 10
rubber fitting
58 Indicator bottle glass 25 cc 10
59 Platinum wire 20
Page 9
ANNEXURE- II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT AND MACHINERIES ( Desired Equipment/Hand Tools)
Name Minimum
Sr.No. Technical Specification Remark
of Equpt./Machinery Qtty Reqd
NO DESIRED EQUIPMENT
Page 10
MAHARASHTRA STATE BOARD OF
TECHNICAL EDUCATION, MUMBAI
MINING ENGINEERING
(MS/MN)
one
3 Universal Testing Maximum load: 100kN (10 tonf)
Machine Stroke of jack: 220mm
Distance between tensile chucks: 0-
200mm Split collet chucks Maximum
distance between compression
platens: 220mm Digital read-out load
indicator calibrated in both SI (kN)
and imperial (tonf) units Test
Specimens
Sr. No. Name of the Eqpt. / Technical Specifications Minimum Qty / Remark if
Machinery Nos Reqd any
1 Total Station Angular measurement Standard one
deviation per ISO17123-3, 1 σ 1) 0.5“
(0.15 mgon) Units of measurement
360° sexagesimal, 400 gon 360°
decimal, 6400 mil Display 0.01
mgon; 0.1“, 0.00001°, (smallest
selectable unit) 0.00001 mil
Automatic reference to the horizon (2-
axis liquid compensator) Working
range, longitudinal/lateral 3' (0.055
gon) Setting accuracy ≤ 0.3“ (0.1
mgon) Displays LCD (liquid crystal
display) 8 rows of 35 characters each
6 status fields Data storage and
interfaces PCMCIA memory card
RS232 programmable interface Motor
and fine drives Fine drives
Coarse/fine, motorised, infinite, slip
coupling Motor Speed of rotation 45
°/s (50 gon/s) Positioning accuracy
0.8” (0.2 mgon)
2 DIGITAL Angular Accuracy : 10” (Second) or two
(ELECTRONIC) better.
THEODOLITE Least Count : 10” (Second) or less
Telescope Magnification : 30 X,
Telescope Image : Upright/Erect,
Shortest Focusing Distance : 1.7 M or
Less., Angle Measurement :
Continuous
Compensetor : Dual Axis., Display :
L.C.D.
Plummet : Laser/Optical, Power
Supply : 2 nos. NIMH, 6V. Re-
chargeable, internal and 1 no.
External Batteries
per Unit Set., Charger : 1 no. suitable
quick charger for internal and
external batteries with 2 nos.
Charging cable/Cord and adaptor per
unit set. Operating Temp. : (-) 200 C
to 500 C
Telescopic Tripod (Wooden) : 1 per
Unit set with Canvas carrying bag
with shoulder strap.
Minimum
Name of the Eqpt. / Quantity / Nos Remark if
Sr. No. Machinery Technical Specifications Reqd any
1 Nil Nil Nil
MAHARASHTRA STATE BOARD OF
TECHNICAL EDUCATION, MUMBAI
METALLURGICAL ENGINEERING
(MT)
Page 1 of 17
INDEX
Sr. No. Essential Equipments Labwise, Annexture-I Page No.
1 Heart Treatment 1
2 Testing of Materials 2
3 Chemical Analysis 3
4 Physical Metallurgy 4
5 Foundry Shop 5
6 Basic Metallurgy 6
7 Metal Working 7
8 Computer 8
1 Heart Treatment 9
2 Testing of Materials 9
3 Chemical Analysis 10
4 Physical Metallurgy 10
5 Foundry Shop 11
6 Basic Metallurgy 11
7 Metal Working 12
8 Computer 12
Page 2 of 17
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
Minimum Remark
Sr. No. Name of Equipment / Machinery Technical Specifications Qtty./ Nos if any
Required
1 Resistance furnace(salt bath type) 12000c 6*6*12 inch 1
0
2 Muffle Furnace 1000 c 6*6*12 inch 1
0
3 High temperature heating furnace 1200 c 6*6*12 inch 1
4 Heat treatment high
temperature furnace 10000c 6*6*9 inch 1
230V/50HZ, single
5 Jominy End Quench Apparatus phase motorized 1 Metatech
water circulation
with storage tank pune.
Page 3 of 17
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
Minimum Remark if
Sr. No. Name of Equipment / Machinery Technical Specifications Qtty./ Nos any
Required
able to conduct izod and
1 Digital Impact testing machine charpy test, 1
charpy striker, izod striker
,v and u
milling cutter,pendulum
impact energy
300J and 170 J.
Max. bending moment
2 Fatigue Testing machine -200 kg-cm 1
gripping diameer-12mm
testing diameter of
specimen -08mm
digital counter -08 no. of digits.
3 Digital Rockwell Hardness tester Max test height -265 mm 1
depth of throa-148mm
max depth of screw
below base-
270mm
4 Rockwell superficial hardness tester major load- 15,30,45 Kgf 1
Loads- 49 -1177 N
5 Vickers Hardness Tester ,Magnification- 1
35-140x hardness
conversion table
6 Ultrasonic Testing package Frequency-0.5-2.5MHz, 1
mullti curve DAC and
DGS Evaluation
7 Univarsal Testing MachineM Digital Display,25Ton 1
Load-153- 2450 N,
8 Brinell hardness tester 10mm Ball indentor. 1
Page 4 of 17
9 Magnaflux Machine insection length-upto 600mm 1
coil diameter 150mm
magnetizing current-
AC &HWDC
200-1000A
for measuring hardness
10 Sclero-rebound hardness tester hrc,hrb ,brinell 1
and tensile strength
11 Poldi impact hardness tester 30x measuring microscope 1
Page 5 of 17
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
Minimum Remark if
Sr. No. Name of Equipment / Machinery Technical Specifications Qtty./ Nos any
Required
with combustible
1 C-S determination Apparatus combustion tube 1
(Strohlein,s) furnace and control panel,
tempertature controller
upto 1600 0C
2 Hot Plate 45X60 cm with 3 heat control 6
Page 6 of 17
ANNEXURE - I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
Minimum Remark if
Sr. No. Name of Equipment / Machinery Technical Specifications Qtty./ Nos any
Required
hydrolic with mould heater,
1 Mounting Press fast 1
cooling and timer facilities,
std mould
assembly- 1"
capacity- 60-100mm
2 Abrasive cut off machine round bar, high 1
power backup motor
disc 200mm ,polishing
3 Grinding/Polishing Machine load -150Psi 1
1hp motor dc ,6
specimen polishied
at a time with sample
leveling press
Magnification upto
4 Inverted Microscope 1000x with polariser, 1
high numerical apperture
and resolution
5 Glass plates 10mm thick,9x12 inch 60
2 dozen
6 Emery papers 0/1, 2.,3,4 each
Page 7 of 17
10-100x magnification
7 Metallurgical microscopes with mechnical 12
and circular stagethrough
3600
8 Monitor,Video, Camera for microphotography 1 each
for microphotography
9 dark room(8x10 feet) with enlarger, 1
camera, cutter,glazing machine
10 Belt grinder 1/4hp motor, 220v single phase, 1
endless belt dimenssion
-100x915mm
Page 8 of 17
ANNEXURE - I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
Minimum Remark if
Sr. No. Name of Equipment / Machinery Technical Specifications Qtty./ Nos any
Required
1 1. Melting Furnace 1400 0C,resistance heating,chamb 1
type,with automatic temperature
controller
2 Sand Muller - mixer machine Roller rotation,50-100rpm,50kg capacity
3 Moulding Boxes (flask-metallic) 340x340x60mm 24
4 Infrared Moisture detemination infrard bulb 1
apparatus
5 Rapid moisture teller std. Set 1
6 Permeability Meter std. Set 1
7 Specimen Sand Rammer std. Set
8 Universal sand strength testing std. Set 1
machine
9 mould and core hardness tester std. Set 1
10 Mould Shake-out (mech) machine vibrating type
std. Set with nest of 07 sieves
11 Sieve shaker and pan 1
12 Patterns wooden and metal pattterns 12
13 foundry tools std. Kit 1
14 blower 1
Page 9 of 17
ANNEXURE - I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
Minimum Remark if
Sr. No. Name of Equipment / Machinery Technical Specifications Qtty./ Nos any
Required
electrically heated with
1 Redwood Viscometer energy regulator and 1
controller for liquid .
electrically heated with
2 Ables.Flash and Fire Point apparatus energy regulator and 1
controller for oil
for measuring cv of fuel,
3 Bomb calorimeter std. Set 1
4 Hall flow meter 1/10" and 1/8" openings 1
bcc ,fcc, hcp,grahite
5 models of crystal structures diamond,bct 1
Page 10 of 17
ANNEXURE - I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
Minimum Remark if
Sr. No. Name of Equipment / Machinery Technical Specifications Qtty./ Nos any
Required
8x3/4"wth rough and
1 Double ended bench grinder smooth wheels, 1
2800rpm
2 Lathe Machine Lab type std. Machine 1 hmt make
Lab type std. Machine
3 Spinning lathe machine with wooden 1
former
3m table length, for
4 Draw Bench machine drawing wire 1
7mm-23 swg tungsten
carbide die.
18" C.I. Drum,12swg-16swg
5 Bull lock machine drawing 1
capacity
85mmx150mm 5hp, 440v,
6 Rolling Mill 3 phase motor 1
fitted with blade and
7 Shearing Machine handle for sheet 1
cutting
9 Mechanical Press 10 ton capacity 1
10 Hydraulic Press 25 tons capacity 1
10 Drilling Machine portable 1"size 1
11 Erischons Cupping Testing machine Lab type std. Machine 1 blue star
engg,mumbai
12 Oxy- acetylene gas welding unit complete set 1
13 Electric arc welding unit complete set 1
Page 11 of 17
ANNEXURE - I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
Minimum Remark if
Sr. No. Name of Equipment / Machinery Technical Specifications Qtty./ Nos any
Required
1 P.C. P-IV with internet facilities 20 HCL
Page 12 of 17
ANNEXURE - II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
Minimum Remark if
Sr. No. Name of Equipment / Machinery Technical Specifications Qtty./ Nos any
Required
1 pack carburising carburizing box, 4x6 inch 1
2 flame hardening pilot flme hardening set up 1
Page 13 of 17
ANNEXURE - II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERY ( Desired Equipment/Hand Tools)
( Optional Equipment)
Minimum Remark if
Sr. No. Name of Equipment / Machinery Technical Specifications Qtty./ Nos any
Required
1 portable rockwell hardness tester indentor-1/8-1/16 inch steel ball/d 1
major load -60-150 kg
scale A,B,C
2 X-ray Radiography unit 1 Mu detail detectability,320 W ta 1
6 axis manupulation, various tube voltages.
3 Portable hardness tester 7 different probesReadings in 1
HV,HB,HRA,HRB,HRC,HS,HLD,UTS
Page 14 of 17
ANNEXURE - II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
Minimum Remark if
Sr. No. Name of Equipment / Machinery Technical Specifications Qtty./ Nos any
Required
1 C-S determination Apparatus Leco make, digital display 1
quntitative and qqualitatative
2 Spectrometer analysis of 1
ferrous and nonferrous
metal and alloys,
absorption/ emmision type
3 D.C. Regulator 20v and 15A 1
4 Vats for electroplating 3x2x4feet 2
5 Polishing and buffing machine standard 1
Page 15 of 17
ANNEXURE - II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
Minimum Remark if
Sr. No. Name of Equipment / Machinery Technical Specifications Qtty./ Nos any
Required
Quantitative analysis with
1 Image Analysis system software like 1
grain size measurement,
phase ,inclusion
,nodules analysis,hardware with
color/ccd/digital camera,
latest computer with
optomechanical
adoptor
Specimen prepared within
2 Electrolytic polysing Machine 30 second,
microcontroller technology
,suitable
for all metals
load- 10-1000gf,
3 Microhaardness tester digital measuring, dwell time 1
5-60 sec. Built in printer,
knoop indentor
Page 16 of 17
ANNEXURE - II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
Minimum Remark if
Sr. No. Name of Equipment / Machinery Technical Specifications Qtty./ Nos any
Required
1 Gravity Die Casting machine std set 1
2 sand blasting unit std set 1
3 core extrsion machine std. Set
4 software for casting simulation systemsolid cast,flow cast and opti cast s 1 Eds tech.
with hardware Banglore
Page 17 of 17
MAHARASHTRA STATE BOARD OF
TECHNICAL EDUCATION, MUMBAI
PACKAGING TECHNOLOGY
(PK)
Page 1
INDEX
List of Equipment & Machinery
(Essential Equipments)
Page 2
ANNEXTURE-I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERY (Essential Equipment/Hand Tools)
(Required For Conducting The Practicals)
1. Name of Course / Department - Diploma In Packaging Technology
2. Name of Laboratory - Packaging Material and Package Testing Labortary
Minimum
Remark
Sr. No. Nameof Equpt./Machinery Technical Specifications Otty./Nos
if any
Required
1 Universal Testing Machine I. Digital Load Indicator :
a) Loading Capacity
50/100/500/1000/ 2000 kgf. Max.
b) Load Cell Capacity
50/100/500/1000/ 2000
c) Load Indicator Resolution : 1 No.
0.1% Full Scale.
d) Load Indicator Accuracy : +
0.4% FS
e) Admit between Platens : 20 -
500 mm
f) Loading Speed : 15mm/min
approx. (or as per request)
II. Digital Length Indicator :
a) Length Indicator Resolution : 0.1
mm
b) Length Indicator Accuracy :
+0.2 mm
2 Puncture Resistance Tester Dimension :
Depth : 431 mm (17 in)
Height : 559 mm (22 in)
Width : 686 mm
Net Weight : 87kg.
Gross Weight : 140kg. 1 No.
Accessories :
Small Lever Holding Packate for
1/2 Pendulum Swing
Test Compliance :
TAPPI T-803 om - 88
IS-4006 (Part II) 1972
Page 3
3 Bursting Strength Tester a) 1/4 H.P. Single Phase 220 volts
1440 R.P.M. motor
b) Fitted with large 10 cm dia (4")
dial and lazy hand indicator and
c) A precise and reliable machine.
Page 4
6 Box Compression Tester Box Compression Strength Tester.
(Digital Mode)
Based On : IS 7028 (PartVI)-1973,
IS-7028 (Part - IX)-1975, Tappi : T-
Testing Speed : 10 + 3mm Per 1 No.
Minute (1/2" Per Minute)
Electric Supply : Three Phase 415
V-AC, at 50 Htz. With positive
Electric Motor : Three Phase 415 V-
AC 1 HP 2 Speed Induction Motor
Loading Capacity : Max.
Compression Load upto 1,000 kgf.
7 Vibration Tester Floor Space Requirement : -
1200 mm x 1500 mm
Table Size:- 1000 mm x 1000 mm
Railing Guard Height :- 300 mm
Table & Rails :- Wooden
Electric Motor :- 1HP, 3Phase, 1 No.
1400rpm
Amplitude :- Fixed 25mm
Frequency : Variable Between 3-10
Htz
(180 - 600 cycles per minute)
Vibrations:- (a) Harmonious - In
phase - Out of phase (60 0 & 1800)
(b) Random.
8 Drop Tester Drop Heights - Max. 1770 mm
Min. 660mm
With interval of Every 75 mm
Spring loaded drop arm
Max. Weight of the test Package: 1 No.
75 k
Max. size of the package :
600 x 600 x 600 mm
Limit switches
Page 5
9 Coefficient of Friction Tester Accuracy - 1 degree
Range - 0 -5
Stroke - 10mm to 50mm
Test Speed - 100 mm/min 1 No.
Power : AC220V-50Hz.
Dimension : 470(L) x 310(B) x
200(H)
Measuring Standard as per ISO
8295, ASTM B-1994, TAPPI - T
816
10 Heat Seal Tester Seal Tempt. 25 - 3000,
Dwell time : 0.1 to 999 Sec.
Dwell Pressure : 0.5 to 0.7 mpa
Seal Surfess : 150 x 10 1 No.
Dimension : 380(L) x 300 (B) x
450(H)
Power : AC250V-50Hz.
11 Air Conditioner for Test Chamber 1.5 Ton (15 x 20 Chamber)
Humidifying / Dehumidifying / 1 No.
temp. control devices
Weight - 70 kg.
13 Tearing Strength Tester Capacitiz of Pendulum : 200 gf., 1 No.
400 gf., 800 gf, 1600gf, 3200gf 480
(L) x 380 (B) x 560(H) Power
supply : AC220V-50Hz. Net
Weight : 23.5 kg Conducting
Standared Test - ISO 6383, ISO -
1974
Page 6
ANNEXURE-1
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERY(Essential Equipments/hand Tools)
(Required for Conducting the Practicals)
1 Name Course/Department- Packaging Technology
2 Name of Laboratory- Package Conversion And Processes Laboratory
Sr.No. Name Of Equpt/Machinery Technical Specifications Minimum Remark
Qtty./Nos. if Any
Required
1 Vertical Type Single Face Corrugator Size-42",Output-70ft./min ,Power- 01 No.
3HP, For `B` Type Flute
2 Sheet Pasting Machine Size-75" Width,Output-60 01 No.
Mtrs/Min.,HP-0.5,
3 Rotary Shear Size- 52",Cutting Leading 01 No.
Mini.20"/Max.100",Power- 3HP
4 Sheet Pressing Machine Size- 65"x75", Height Of M/c.84", 01 No.
HP- 2
5 4 bar Rotary Cutting & Creasing Size- 75", Output 100 Mtrs./min, 01 Mo.
Machine Min. Distance betn. 2 discs-
3",Power- 3HP
6 Eccentric Slotter Size- 75", Stroks/pm-30,Slot Depth- 01 No.
18", Min. Distance /slot.- 7",Power-
3HP
7 Box Stitching/Stapling Machine Size- 30", Stitch/pm- 250, Power- 01 No.
0.5 HP
8 Horizontal FFS Or Pouch Wrapping 1.Package size--WxHxL (1)20- 01 No.
Machine 70mm-5x65mm-40x250mm ,(2)
Packing Material Reel width-
300mm.Max.(3) A.C.Drive 3Ph.(4)
Load upto 1.5 kg. (5) Suitable for
any heat sealable plain or
laminated film.
9 Platen Die Punching Machine 1.Platen size - 55x70cm, 2.Max Str.- 01 N0.
1200, 3.Impression/hr.-2000,
4. HP-3, Suitable for
cutting/creasing & pressing various
papers,CFB & SFB for carton &
box making
Page 7
10 Paper Bag Making Machine(Junior) 1. Size of paperbag W- 01 No.
3x20cm,L-10x20cm, side
guard-4-7cm. 2.
GSM of paper -40-70
3. BF-12-18 4.
Paper roll width max.56-60cm.
5. Prodn. 1000 bags/hr 6.
Printing attachment optional. 7.
Motor-1 HP.
11 Thermoformer 1. Forming table size 300x400, (a) 01 No.
width max400-Min150, (b) Length
Max300-Min50, (c) Draw Max100,
2. Width of roll adjustable
(a)Max425, (b) Min175., 3.
Max speed 12cycle/min., 4. side
chain hold wastage 25mm,
5. Heater element-Top 4Kw,
Bottom 4Kw
6. Overall Dimensions- 3x1.2x1.8
M 7.
Total Power Load 12Kw 8.
Compressed air at 5Kg/cm², 100
lit/min.
Page 8
14 Vertical Form Fill Sealing Machine 1. Suitable for filling Powders, 01 No.
granules, pastes, liquids, cream
2. Filling Range- 50 gm to 1000
gm
3. Output- 30 packs/min. 4.
Pack size- Width- 50-250 mm,
Length- 70-300 mm
15 Pallet Stretch Wrapping Machine Max. Wrapping Height - 2360mm 01 No.
Page 9
ANNEXURE-1
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERY(Essential Equipments/hand Tools)
(Required for Conducting the Practicals)
1 Name Course/Department- Packaging Technology
2 Name of Laboratory- Printing And Labelling Laboratory
Page 10
3 Self Adhesive Labelling Machine For wrap arround or 5/w.a.
lebeling applied on cylendrical
paper
1) Paper Passage - 100
2) Max. Label L - 150 1 No.
3) Inside Dai - 45/76
4) Outred Dai - 300
5) Compressed air bar -
4/6kgf/cm2
6) Power - 1kw
4 Semi automatic vertical process Camera
Size:
Max. film : 510 x 610 mm (20" x
24")
Max. copy : 560 x 735mm (22" x 1 No.
29")
Optional : Back light for
transparencies (16" x 20") 455 x
585mm (18" x 23")
5 Contact Printer Size:
510 x 610mm (20" 24") 1 No.
760 x 1015mm (30"x40")
6 Film Dryer Size:
Min. film width - 65mm (25") 1 No.
Max. Film width - 510mm (20")
7 Film Register Punch with Film Cutter Laminated board with markings in 1 No.
metric and ISO sizes, No burr or
Blunt edges on the film or paper,
due to special steel disck cutter.
Maximum film size: 610mm (24")
Page 11
9 Plate Developing Sink Ideal alternative to permanent brick 1 No.
and tiled construction for optimum
space utility.
Chemical resistant fibre glass body
of sink.
Light weight
Better efficiency and higher
productivity.
MS angle iron Frame.
convenient drain outlet
Plat size:
510 x 760mm (20" x 30")
860 x 1015mm (34" x 40")
10 Dark Room Process Sink Suitable for processing of 1 No.
phtographic material.
Fabricated from Fibreglass
moulding.
MS sturdy stand with sink
Weste water disposal outlet is in
built.
Inside sink sizes :
1830 x 760mm (72" x 30")
2440 x 760mm (96" x 30")
Page 12
ANNEXTURE-II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERY (Desired Equipment/Hand Tools)
(Optional Equipment)
1. Name of Course / Department - Diploma In Packaging Technology
2. Name of Laboratory - Packaging Material and Package Testing Labortary
Minimum
Remark
Sr. No. Nameof Equpt. / Machinery Technical Specifications Otty./Nos
if any
Required
1 Smoothness Tester Meets ISO 5627, TAPPI T-479,
DIN 53107
Range - 0 - 99000 sec.
Test result and Statastic display in 1 No.
bekk sec.
Instrument size :
D-53mm x H-450mm x W-
390mm
Weight : 70kg
2 Brightness Tester Brightness TAPPI Instrument
Brightimeter Model - S4-M
Fully Automatic Instrument
with computer interfacing 1 No.
measuring brightness
as per TAPPI Test Method
T-452 and ASTM Standard
D-985
3 Tearing Strength Tester Capacitiz of Pendulum :
200 gf., 400 gf., 800 gf, 1600gf,
3200gf.
480 (L) x 380 (B) x 560(H) 1 No.
Power supply : AC220V-50Hz.
Net Weight : 23.5 kg.
Conducting Standared Test - ISO
6383, ISO - 1974
Page 13
4 Inclined Impact Tester IS-7028 (Part 3) - 1987
Equipment : Consist of two rail
steel track inclined at 10 0 to the
horizontal and distances along the
inclined graduted at interval of
50mm
Rolling Carriage or Dolly
and rolles with known velocity.
Impact surface (Bumper) as per IS
specification and placed vertical
(900 to the inclined)
Page 14
ANNEXURE-II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERY(Desired Equipments/hand Tools)
(Optional Equipments)
1 Name Course/Department- Packaging Technology
2 Name of Laboratory- Package Conversion & Processes Lab.
Page 15
Total Power - 29.8kw
Dimension of Machine :
L-2300mm, W-2400mm, H-
2200mm , Weight -1000kg approx.
Page 16
ANNEXURE-II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERY(Desired Equipments/hand Tools)
(Optional Equipment)
1 Name Course/Department- Packaging Technology
2 Name of Laboratory- Printing And Labelling Laboratory
Page 17
MAHARASHTRA STATE BOARD OF
TECHNICAL EDUCATION, MUMBAI
Workshop Technology
(INTERDISCIPLINARY)
Other Than ME Group
INDEX
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
NAME OF COURSE : WORKSHOP
LIST OF EQUIPMENT & MACHINERY
Sr. Essential Equipments Lab wise Page No.
No.
1 Carpentry Shop 1
2 Fitting Shop 3
3 Smithy Shop 5
4 Welding Shop 6
5 Sheet Metal Plumbing Shop 8
9
Page 1
INDEX
Page 2
Annexure-I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Essential Equipment/Hand Tools)
(Required for Conducting The Practicals)
Minium
Remark if
Sr.No. Name of Equpt./Machinery Technical Specification Qty.Nos
any.
Required
Page 3
11 C++ Complete Version 20 User
12 MS Office Office XP 20 User The Computers
13 CorelDraw Prof. Edition 20 User in
14 Ethernet Switch 24 Port 1 this lab.
15 Antivirus Software Online Protection with Firewall securities 20 User Must be
16 Printer Laserjet 30 PPM 16 MB RAM 1200 DPI 1 connected
using
Max Media Size (Custom), 42 in x 150 ft. Print
Windows XP
17 Plotter Speed, Up to 82.9 sq.ft/hour - color. Max Resolution 1 Network
( B&W ), 2400 dpi x 1200 dpi environment
18 Printer Ink Jet Printer. 1 with internet
19 Scanner A4 Size 1 facility
Page 4
Annexure-II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Desired Equipment/Hand Tools)
(Optional Equipments)
Minium
Remark if
Sr.No. Name of Equpt./Machinery Technical Specification Qty.Nos
any.
Required
No Desired Equipment
Page 5
MAHARASHTRA STATE BOARD OF
TECHNICAL EDUCATION, MUMBAI
APPLIED MECHANICS
(INTERDISCIPLINARY)
Other Than Civil Engineering Group
1 of 13
INDEX
Sr No. Essential Equipments Labwise Page No
1 Engineering Mechanics Lab 1
2 Strength of Materials Lab 5
2 of 13
ANNEXURE I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Essential Equipment/Hand Tools)
(Required For Conducting The Practicals)
4 Parallel forces apparatus The apparatus is with two circular dial type 5
(overhang beam type). 10 kg. Extension spring balances
(accurately calibrated). Complete with
suitable stands, a wooden beam with scale
and slots at regular intervals four stirrups
with hooks and four 1 kg. And 1/2 kg.
Weights each. The beam shall be
suspended below dial guages.
3 of 13
5 Inclined plane It consists of 15cm x 60cm wooden board 5
with glass top hinged on an iron base to
which a sector with graduated arc and
vertical scale is provided. The plane may be
clamped at any angle up to 45 degrees. A 5
cm dia. friction less pulley (one additional)
is attached to the end by means of a clamp
adjustable to any necessary position.
Complete with brass roller cart and pan.
Two weight boxes (each of 5 gm, 10 gm, 2-
20 gm, 2-50 gm, 2-100 gm weight), Boxes
each weighing 300 gm with 8 mmply case
and bottom of differents surfaces like,
glass, teak-wood, brass, copper, sand
paper and card board.
7 Diffrerential axle and wheel The wheel is of 40 cm dia and axles are 3
insteps of 20 cm and 10 cm reducing
diameter giving a ratio of 1:2:4. A steel axle
passes through the centre of the wheel
supported on ball bearings in iron brackets.
The base is provided with holes to fix the
appartus on walls or bracketed frame
complete with snatch pulley block cord and
hooks but without weight.
8 Screw Jack All metallic construction accurately 3
machined cut screw with a pitch of 5mm
carrying a double flanged turn table of 20
cm diameter fitted on steel base and
complete with two adjustable pulleys, cords
and hooks.
9 Differential pulley block. A cast iron double sheave pulley block 3
having 16 no. of cogs on bigger pulley and
8 no. of cogs on smaller pulley mounted on
sturdy cast iron bracket and moving freely
on two steel free bearings. A snatch pulley
of 10 cm dia with hook at bottom shall be
supplied along with a continuous steel
chain, along with a hook for effort..
4 of 13
10 Geared pulley block Consists of a metallic (preferably steel) 3
cogged wheel of about 20 cm dia with
endless chain and a gear toothed wheel of
15 cm dia mounted on the same axis. This
toothed wheel shall mesh with another
toothed wheel of same dia along with a
protruded load drum of 10 cm dia to which a
rope can be attached so as to suspend the
weights of 10 kg, 20 kg-2 weights and a 50
kg weighs. The slotted weights of 1 kg-2
weights, 2 kg-2 weights, 5 kg-2 weights and
10 kg weight along with a hook for effort.
11 Single purchase crab Fitted with heavy cast iron wall brackets and 3
attachable to protable M.S.framed trolley.
The effort wheel is of C.I.material of 25 cm
diameter with a hole for effort attachment
mounted on a shaft of about 40mm dia. On
the same shaft a geared wheel (machine
cut) of 15 cm dia shall be mounted. The
teeth of this pinion wheel shall mesh with
another (spur) toothed wheel of 30 cm
diameter. This spur wheel shall be mounted
on another axle to which a load drum of
about 7.5 cm diameter of heavy C.I.
material shall be attached to which the
heavy loads can be attached at bottom. A
set of 5 slotted weights of 2 kg each and a
hanger of 2 kg..
12 Double purchase crab. Having assembly same as above (Sr.No.11) 3
but with double set of gearing arrangement.
A set of 5-slotted weights of 5 kg each and
hanger of 5 kg.
13 Worm and worm wheel Consisting of machine cut worm nickelled 3
steel gear of 25 cm diameter carrying a
metal drum protruding 5 cm of 12.5 cm
diameter above which a machine cut worm
on steel spindle carrying a 12.5 cm dia
pulley. The whole arrangement shall be
fixable on heavy cast iron brackets capable
to be fixed to a wall or a m.s. framed trolley
complete with effort pulley, string
and/hooks, with 5 weights of 1 kg each and
a hanger of 1 kg..
5 of 13
14 Pulley demonstration set Comprising of wooden polish base of about 2
100x20 cm size with two metal supports
and a horizontal bar having eight adjustable
collars with hooks from which pulleys can
be suspended. The following accossories
shall be provided with the unit : (1) Single
pulley with two hooks-7, slotted weights -10
gm- 3 nos, Pulley triple long - 2, slotted
weights-20gm - 3 nos, Pulley triple parallel-
2, slotted weights-50 gm - 2 nos., Wheel
and axle -1, slotted weights-100gm - 7 nos,
Capstan - 1, slotted weights-200gm, 4 nos,
Slotted weights hanger -50gms-7 and 20 m
cord, slotted weights and hangers are made
of iron and duly nickelled.
6 of 13
18 Balance Capacity 5 kg., resolution 0.1 gm. 1
Notes : 1 : Equipment/apparatus recommended for
labouratory preferably be procured digital
and electronic based display with or without
analog display provision.
2 : Computer laboratory equipped with 10
PCs, 1 server, 1 UPS, 1 LCD, 1 OHP
projection system be provided for Applied
Mechanics Deptt.
3 : While calling quotations for
procurement of Lab. equipment, suppliers
shall be asked to submit copy of IS of
manufacturing specifications and IS of test
conductance (where applicable) of supplied
equipment for performance/verifying
purpose.
4 Each apparatus/equipment along with
their accessories must be with ISI mark
(wherever applicable).
7 of 13
ANNEXURE I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Essential Equipment/Hand Tools)
(Required For Conducting The Practicals)
8 of 13
6 Torsion testing machine As per IS 1717, Capacity 50 Kg.M., Ranges 1
50, 25, 10 Kg.m., of div. on dial 500,
Torsion speed, fixed direction, Grip
between round bars (mm) - 10-30 mm,
for flat bars (mm) - 5-12 mm, Width (mm) -
40 mm, Gear motor 3 hp - 0.5.
9 Accessories Vernier calliper, Meter scales, Weights, LS
Balance, Punch, File, Hammer etc.
Notes : 1 : Equipment/apparatus recommended for
labouratory preferably be procured digital
and electronic based display with or without
analog display provision.
2 : Computer laboratory equipped with 10
PCs, 1 server, 1 UPS, 1 LCD, 1 OHP
projection system be provided for Applied
Mechanics Deptt.
3 : While calling quotations for
procurement of Lab. equipment, suppliers
shall be asked to submit copy of IS of
manufacturing specifications and IS of test
conductance (where applicable) of supplied
equipment for performance/verifying
purpose.
4 Each apparatus/equipment along with
their accessories must be with ISI mark
(wherever applicable).
9 of 13
ANNEXURE II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Desirable Equipment/Hand Tools)
(Optional Equipments)
1 Vehicle screw jack used All metallic body accurately machine cut 3
for different four wheelers screw with different pitches so as to carry a
tyre load of vehicle 20 t, 10t and 4 t load
carrying capacity. Fitted on a heavy cast
iron base and complete with appropriate
lever arm.
2 Structural mechanics An equipment to form different trusses with 1
apparatus the given material and find out stress in
different members. It consists of fourteen
types of models enlisted below : (1) Single
contilever, (2) Cantilever with four
members, (3) simple roof truss, (4) Roof
truss with angled tie rods (Roof Truss'A'),
(5) A composite frame work (four in one
frame), (6) King post roof truss, (7)
Standard roof truss (Roof truss'B'), (8) Roof
truss with loads or standard roof truss, (9)
Mansard roof truss, (10) Island roof truss,
(11) N Type girder, (12) Warren girder, (13)
Framed arch, (14) North light roof truss.
Details of accessories : (a) Stand and
cross bars (4 bars and 8 stands) - 4 sets,
(b) Brackets fitted with stands - 4 only, (c)
Hinges (different) - 22 only, (d) Hinge
holder hooks - 8 only, (e) Cantilever rod
with top caps -2 only, (f) Member rods
(sizes marked)-37 only, (g) Cap screws
(extra) - 6 only, (h) Weight hanger with
platform - 8 only, (i) Weight platforms extra -
2 only, (j) Slotted weights 1 Kg. -10 only, (k)
Calibrated spring balances (2 of 20 kg., 2 of
10 of 13
(l)Chains short and long - 6 only, (m) Boss
brackets - 1 only, (n) Ring brackets - 5 only,
(o) Hook brackets - 4 only, (p) Pulley
brackets - 3 only, (q) Member balances to
indicate tensile force - 3 only, (r) Member
balances to indicate compressive force - 3
only. All parts are interchangeable so that
the different frame works can be assembled
with same components
11 of 13
ANNEXURE II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Desirable/Equipment/Hand Tools)
(Optional Equipments)
12 of 13
3 Accessories Vernier calliper, Meter scales, Weights, LS
Balance, Punch, File, Hammer etc.
Notes : 1 : Equipment/apparatus recommended for
labouratory preferably be procured digital
and electronic based display with or without
analog display provision.
2 : Computer laboratory equipped with 10
PCs, 1 server, 1 UPS, 1 LCD, 1 OHP
projection system be provided for Applied
Mechanics Deptt.
3 : While calling quotations for
procurement of Lab. equipment, suppliers
shall be asked to submit copy of IS of
manufacturing specifications and IS of test
conductance (where applicable) of supplied
equipment for performance/verifying
purpose.
4 Each apparatus/equipment along with
their accessories must be with ISI mark
(wherever applicable).
13 of 13
MAHARASHTRA STATE BOARD OF
TECHNICAL EDUCATION, MUMBAI
Not Applicable
ANNEXURE-1
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Essential Equipment/ Hand Tools)
(Required For Conducting The Practicals)
Minimum
Name of Equipt./
Sr.No Technical Specifications Qtty./Nos Remark
Machinery
Reqd
1.0 KVA , 1 Phase, 50 Hz
230/115 V Parallel
Secondary tappings at 5%, 50%, 86.6% Operation
of
1 Transformer 2
transformer
/ Back to
back Test
25 KVA,
To provide
Input :- 415 V , 3 phase 50Hz, 36 A
3 Rectifier 1 D.C.
D.C. output :- 0-230V variable ,Current 100A
supply
Page 3
Wire wound resistors. Variable. Three terminals.
With steel clamp + Brush type moving contact.
± 5% tolerance
400 Ω , 1 A
100 Ω , 5 A V and
6 Rheostat 150 Ω, 2 A 05 each inverted V
110 Ω, 2,5 A curves
40 V, 5 A
20 Ω, 10 A
Page 4
Single Phase 2.5/5 Amp. 200/400 V 3
14 Wattmeters
Single Phase 5/10 Amp. 250/500 V 3
Single Phase 5/10 Amp. 250/500 V 2
15 Low P.F. Wattmeters
AC, 230V,45-50-55 Hz 2
16 1-Ph, Loading Inductor 1 Ph,230V, 10 Amp 1
17 1-Ph, Variable Capacitor 2 Ph,230V, 5 Amp 1
18 Dimmerstat Input-230V output 270V 20Amp. 4
Scientific , 20MHz, digital storage oscolloscope-
19 Dual Trace Oscilloscope HM205-2 2
20 D.C. Regulated Power Suppl0-30V, 2Amp 5
10kW, 230V 1
21 3-Phase Variable load 20kW, 230V 2
22 3-Phase auto Transformer 415V, 15A 2
Verification of Verification of Superposition Theorem Trainer kit should
Superposition Theorem Kit be totallu
23 Trainer Kit 1 enclosed in
Verification of Thevenin's Verification of Thevenin's Theorem Trainer Kit a
24 Theorem Trainer Kit 1 transparent
Verification of Maximum Verification of Maximum Power Trasfer cabinet, it
Power Trasfer Theorem Theorem Trainer Kit should be
25 Trainer Kit 1 ready to
Verification of Norton's Verification of Norton's Theorem Trainer Kit connet to
Theorem Trainer Kit 230V,
26 1
50Hz, a.c.
Verification of Kirchoff's Verification of Kirchoff's Laws Trainer Kit
supply.
27 Laws Trainer Kit 1
Output
28 Clip on ammeter 2
29 Induction Energymeters 1 Phase 230 V, 10 A 2
30 Megger As per standard 2
31 Earth Tester As per standard 5
32 Lamp Bank 230 V 0-20 A 4
1 Phase, 230 V, 15 A, As per Standard accuracy
33 Energy Meter (Electronics) class 1 2
34 Accessories for wiring 1)Wooden Board 2.5 ft x 3.0 ft, 10 mm ply
installation experiment (2)Half inch casing Caping PVC (3)Elbow,
T, Junction Box etc. (4)Holder, Switch,
(1 way. 2way) (5)PVC block 4 inch 10 each
x 4 inch (6) 1.5 mm square wire
bundle for red, black, green.
Page 5
ANNEXURE-II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
Minimum
Name of Equipt./
Sr.No Technical Specifications Qtty./Nos Remark
Machinery
Reqd
No Desired Equipment
Page 6
LIST OF M.S. APPROVED
COURSES
MAHARASHTRA STATE BOARD OF
TECHNICAL EDUCATION, MUMBAI
Name of
Minimum Qty. /
Sr. No. Equipment / Technical Specifications Remark if any
Nos. Required
Machinery
HARDWARE
Page 3
Annexure-I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Essential Equipment / Hand Tools)
(Required For Conducting The Practicals)
Name of
Minimum Qty. /
Sr. No. Equipment / Technical Specifications Remark if any
Nos. Required
Machinery
SOFTWARE
22
1 Microsoft Windows XP Professional with Service Pack2.
(Licensed)
Office XP with Frontpage 22
2 Microsoft Office
with latest Service Pack. (Licensed)
22
3 Antivirus Any antivirus with latest updates.
(Licensed)
Turbo C 3.0 or higher or Microsoft C 22
4 C Compiler
Compiler. (Licensed)
Microsoft Visual Studio 6.0 with latest 22
5 Microsoft Visual Stu
service pack. (Licensed)
22
6 Crystal Report Seagate Crystal Report 8.5 or latest
(Licensed)
Relational Database
22
7 Management Oracle 9i
(Licensed)
System
Page 4
Annexure-II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
Name of
Minimum Qty. /
Sr. No. Equipment / Technical Specifications Remark if any
Nos. Required
Machinery
HARDWARE
Page 5
Annexure-II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
Name of
Minimum Qty. /
Sr. No. Equipment / Technical Specifications Remark if any
Nos. Required
Machinery
SOFTWARE
22
1 Microsoft Windows XP Professional with Service Pack2.
(Licensed)
Office XP with Frontpage 22
2 Microsoft Office
with latest Service Pack. (Licensed)
22
3 Antivirus Any antivirus with latest updates.
(Licensed)
Turbo C 3.0 or higher or Microsoft C 22
4 C Compiler
Compiler. (Licensed)
Microsoft Visual Studio 6.0 with latest 22
5 Microsoft Visual Stu
service pack. (Licensed)
22
6 Crystal Report Seagate Crystal Report 8.5 or latest
(Licensed)
Relational Database
22
7 Management Oracle 9i
(Licensed)
System
Page 6
MAHARASHTRA STATE BOARD OF
TECHNICAL EDUCATION, MUMBAI
Sr.
List of Essential Equipment Labwise Page No.
No
1 Multimedia Laboratory 1
2 Multimedia Laboratory 2
ANNEXURE-I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Essential Equipment/Hand Tools)
(Required for Conducting The Practicals)
1. Name of Course/Department- Diploma in 3D Animation and Graphics
Minimum
Sr.No Name of Equpt./ Machinery Technical Specifications Remarks
Qty Reqd
Hardware
P-IV 3.4 Ghz, 160 Gb HDD, One
1 Desktop Computer System DVD-Writer, RAM-512 MB, 20 computer per
Graphics Accelerator Card student
Higher Megapixel with 2 Gb
2 Digital Camera 1
memory Card
3 Scanner Hp 4370 or Umax- 5600 1
Hp1320 or Hp 2420
4 Laser Printer 1
or Hp 2840
5 Injet Photoprinter Hp 8758 or Hp 8238 1
LCD Projector with
6 2000 Luminance 1
White Screen
Software
Minimum
Sr.No. Name of Equpt./ Machinery Technical Specifications Remarks
Qty Reqd
Hardware
P-IV 3.4 Ghz, 160 Gb HDD, One
1 Desktop Computer System DVD-Writer, RAM-1 Gb, 20 computer per
Graphics Accelerator Card student
Higher Megapixel with 2 Gb
2 Digital Camera 1
memory Card
3 Scanner Hp 4370 or Umax- 5600 1
Hp1320 or Hp 2420
4 Laser Printer 1
or Hp 2840
5 Injet Photoprinter Hp 8758 or Hp 8238 1
LCD Projector with White
6 2000 Luminance 1
Screen
Software
1 Windows XP/Vista Per PC
2 Page Maker (Latest Version) 20 paper licence
If 20 PC
3 Corel Draw (Latest Version) 20 paper licence
available in
4 Photoshop (Latest Version) 20 paper licence
Network
5 Studio 8 20 paper licence
then
6 Creative Suite 20 paper licence
Software
7 Production studio 20 paper licence
should be
8 Flash Pro. (Latest Version) 20 paper licence Client server
9 Director (Latest Version) 20 paper licence based.
10 MAYA (Latest Version) 20 paper licence
11 3D Max 20 paper licence
12 Anitvirus Latest
MAHARASHTRA STATE BOARD OF
TECHNICAL EDUCATION, MUMBAI
Page 1 of 6
INDEX
Page 2 of 6
Annexure-I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
Name of Minimum
Sr. No. Equipment / Technical Specifications Qty. / Nos. Remark if any
Machinery Required
HARDWARE
Processor : Pentium IV 2.4 GHz or higher.
RAM : 256 MB SD/DD RAM or higher.
Hard Disk : 40GB or higher.
CDROM drive : 48x or higher.
Floppy drive : 1.44 MB.
USB support : Two USB/USB2.0 ports.
1 Desktop PC Multimedia : Onboard / External. 22
LAN card : 10/100 Mbps - Onboard /
External.
Monitor : 15" Colour or higher.
Mouse : 3-button-Scroll.
Keyboard : 104 key keyboard - Simple /
Multimedia.
2 Hub 24 port HUB, 10/100 Mbps. 1
3 Modem Broadband - 10/100 Mbps. 1
Uninterruptible
4 Power Supply 600VA, 20 minutes backup. 1
(UPS)
5 Voltage Stabilizer5KVA 2
6 Printer Laser - A4 size 1
7 Display Monitor LCD, 15" colour 1
8 USB-HDD 40GB or higher 1
9 LCD Projector Colour LCD Projector 1
Page 3 of 6
Annexure-I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Essential Equipment / Hand Tools)
(Required For Conducting The Practicals)
Name of Minimum
Sr. No. Equipment / Technical Specifications Qty. / Nos. Remark if any
Machinery Required
SOFTWARE
22
1 Microsoft WindowXP Professional with Service Pack2.
(Licensed)
Office XP with Frontpage 22
2 Microsoft Office
with latest Service Pack. (Licensed)
22
3 Antivirus Any antivirus with latest updates.
(Licensed)
Turbo C 3.0 or higher or Microsoft C 22
4 C Compiler
Compiler. (Licensed)
Microsoft Visual Studio 6.0 with latest service 22
5 Microsoft Visual
pack. (Licensed)
22
6 Crystal Report Seagate Crystal Report 8.5 or latest
(Licensed)
22
7 PageMaker Adobe PageMaker 6.5 or higher
(Licensed)
Broadband-100 Mbps with proxy server
8 Internet Facility -
facility
Page 4 of 6
Annexure-II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
Name of Minimum
Sr. No. Equipment / Technical Specifications Qty. / Nos. Remark if any
Machinery Required
HARDWARE
Processor : Pentium IV 2.4 GHz or higher.
RAM : 256 MB SD/DD RAM or higher.
Hard Disk : 40GB or higher.
CDROM drive : 48x or higher.
Floppy drive : 1.44 MB.
USB support : Two USB/USB2.0 ports.
1 Desktop PC Multimedia : Onboard / External. 22
LAN card : 10/100 Mbps - Onboard /
External.
Monitor : 15" Colour or higher.
Mouse : 3-button-Scroll.
Keyboard : 104 key keyboard - Simple /
Multimedia.
2 Hub 24 port HUB, 10/100 Mbps. 1
3 Modem Broadband - 10/100 Mbps. 1
Uninterruptible
4 Power Supply 600VA, 20 minutes backup. 1
(UPS)
5 Voltage Stabilizer5KVA 2
6 Printer Dot Matrix - 24 pin, 132 column 1
7 Printer Ink Jet - A4 size 1
8 Printer Laser - A4 size 1
9 Display Monitor LCD, 15" colour 1
10 USB-HDD 40GB or higher 1
11 LCD Projector Colour LCD Projector 1
Page 5 of 6
Annexure-II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
Name of Minimum
Sr. No. Equipment / Technical Specifications Qty. / Nos. Remark if any
Machinery Required
SOFTWARE
22
1 Microsoft WindowXP Professional with Service Pack2.
(Licensed)
Office XP with Frontpage 22
2 Microsoft Office
with latest Service Pack. (Licensed)
22
3 Antivirus Any antivirus with latest updates.
(Licensed)
Turbo C 3.0 or higher or Microsoft C 22
4 C Compiler
Compiler. (Licensed)
Microsoft Visual Studio 6.0 with latest service 22
5 Microsoft Visual
pack. (Licensed)
22
6 Crystal Report Seagate Crystal Report 8.5 or latest
(Licensed)
22
7 PageMaker Adobe PageMaker 6.5 or higher
(Licensed)
Broadband-100 Mbps with proxy server
8 Internet Facility -
facility
Page 6 of 6
MAHARASHTRA STATE BOARD OF
TECHNICAL EDUCATION, MUMBAI
HOTEL OPERATION
(HO)
1
INDEX
DIPLOMA IN HOTEL OPERATION
Sr. No Essential Equipments Page No.
1 Food Production 1
2 Bakery 4
3 Accommodation Operation 7
4 Computer Application 11
5 Food And Beverage 12
Desirable Equipments
6 Food Production 15
7 Bakery 16
8 Accommodation Operation
17
9 Computer Application 18
10 Food And Beverage 19
2
ANNEXURE- I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT& MACHINERY (ESSENTIAL EQUIPMENTS/HAND TOOLS)
NAME OF COURSE :- DIPLOMA IN HOTEL OPERATION
NAME OF LABORATORY :- FOOD PRODUCTION
Sr.No Name of Equpt./Machinery Technical specification Minimun Remark
Qtty/Nos if any
Required
1 Microwave Oven 5 ltr. Capacity with Oven, Toster, Griller, 1
Browner facility
2 4 Burner Gas Range with Oven 515 mm Depth, 630 mm Heigt, 1420mm , 7
Cover open four top burner with sperate
grill & Oven Temprature Thermostatically
controlled.
3 Work Table Standard Size 44" x 24 x 34" with wood 7
made with compartment
4 Stainless steel sink with draining Size 90" x 24" x 34" x6" Drain 7
board board 19" x 18" x 12"
5 Tawa 22 cm Dia meter with Iron Made with 7
handle
6 Salamanders Size 29" x 14" x 14" with Grilling 1
Toasting & Re Heating Elecrically
Operating Model
7 Weighing Scale Portable up to 5 Kg. Measuring Wt. 3
8 Precision scales Supporting Tool 3
9 Food Mixer-with attachments 800 Wt. With frequency of 230 Volt With 2
attachment
10 Masala grinder 3 or 5, kg wet grain with SS Rotating 1
Drum with base box, Heavy Duty Gear
driven motor.
11 Tandoor with rods Hand Tools 1
12 Chinesse Chopper Hand Tools 2
13 Chefs knives Set Hand Tools 2
14 Masala Box SS Box 6" Dia meter with 6 - 8 seprating 7
Bowls
15 Oil Container 200 ml capacity Plactic or SS made 7
16 Plates, Bowels 10" Dia meter plastic or SS Made plates Each 20
/250 ml capacity SS made
17 Chapping Board 60 x 40 x 2 cm with Nylofast made 7
3
20 Entréedishes Dish Lenth 18 -20 cm SS made 30
24 Brass degchited (Small/Med/Large) 6 - 8" Dia meter with Steel made with 7
Brass Base
34 Stainless steel degchi 6 - 8" Dia meter with Steel made with Lid. 7
4
42 Plastic containers Hand Tools 7
5
ANNEXURE- I
6
13 Brioche Moulds Supporting Tool 10
30 Cooling racks-rectangular and round 6, 10, 12 " insize Iron or SS made 2 each
41 Work table with marble top Standard Size 44" x 24 x 34" wood made 10
with compartment Top With Marble
44 Steel degchi 6 - 8" Dia meter with Steel made with Lid. 10
52 Piping bags with set of nozzles Cloths Bag with 0 - 20 No Set of Nozzles 3
8
ANNEXURE- I
3 Computers P-4 2
9
13 Tea Table ht 15" width. 18-24" 2
14 Ashtrays Hand Tool 2
15 Wall Clock Any wall Clock 1
16 Call Bell Electronic Call Bell 3
17 Calulator as per market avability 2
18 Fidelio Software As per Hotel Industry Releated 1
19 Printer Laser 1010 H.P 1
38 Single Bed with Head Board 3ft x 6ft x 11/2 ft with wooden made 2
10
40 Bed Lamp 1
11
61 Bath Mat 30 x 60 cm 1
12
ANNEXURE- I
13
ANNEXURE- I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT& MACHINERY (ESSENTIAL EQUIPMENTS/HAND TOOLS)
NAME OF COURSE :- DIPLOMA IN HOTEL OPERATION
14
13 Fish Knife 8" SS made 12
14 Fish Fork 8" SS made 12
15 Butter Dish & Butter Knife 18 -20 cm SS made 5
16 Quarter Plate 6" Dia Meter Fine Bone China 60
17 Tea Cup 150 ml Fine Bone China 24
18 Cofee Cup 50 ml Fine Bone China 24
19 Saucer 6" Dia Meter Fine Bone China 24
33 Restaurant Tables for four person 3' x 3' Teak Wood made with Melamine 5
polish
34 Restaurant Chairs Full Heigt of chair 3 ft. , Height till the seat 20
1 & 1/2 ft., Back rest 1 & 1/2 ft. , Seat 1 &
35 Table Cloths 4' x 4' ft. Cotton made 5
15
40 Ice tongs Hand Tool 5
16
ANNEXURE- II
8 Deep Fat Fryer single chamber 15" x 21" x 21" with single chamber 1
counter top with Automatic Theromstater
9 Pizz Oven 42" x 24" x 16" with Electrict load 6 Kw / 1
3 Phase with stand
10 Bain Marie - Counter Top 24" x 21" x 11" with SS construction with 1
steaming pot Load 6 Kw.
11 Three Sink Unit 90" x 24" x 34" x 6" Splas with water 1
heater and Thermostatic control Optiomal
over flow system and leaver operated
valve.
12 Kitcheen Cup Board 30" x 20" x 72" storing partation with 1
aluminium construction Purforated door
with locking arragement.
13 Refregctor 1000 Ltr with 4 Door SS made automatic 1
Defrosting system
17
ANNEXURE- II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT& MACHINERY (DESIRABLE EQUIPMENTS/HAND TOOLS)
NAME OF COURSE :- DIPLOMA IN HOTEL OPERATION
NAME OF LABORATORY :- BAKERY
Sr.No Name of Equpt./Machinery Technical specification Minimun Remark
Qtty/Nos if any
Required
1 Jelly moulds Hand Tool 10
2 Mixie 800 Wt. With frequency of 230 Volt With 2
attachment
3 Bakery Oven Two Deck Working Space 1000X1050X200 mm & 1
Heating Load 7 Kw. With SS front with
Glass Window
4 Refrigerated 1000 Ltr with 4 door Ssmade automatic 1
Defrosting system
5 Work table with marble top Standard Size 44" x 24 x 34" wood made 20
with compartment Top With Marble
18
ANNEXURE- II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT& MACHINERY (DESIRABLE EQUIPMENTS/HAND TOOLS)
NAME OF COURSE :- DIPLOMA IN HOTEL OPERATION
NAME OF LABORATORY :- ACCOMMODATION OPERATION
Sr.No Name of Equpt./Machinery Technical specification Minimun Remark
Qtty/Nos if any
Required
1 Laundary Trolley 40" x20"x70" 1
2 Luggage Trolley Ht. 48"x18"wdth 1
3 Cash Box As per required 1
4 Bulletin Board Wooden made to order 1
5 Fax Machine With PC Compatatibility Laser 1
6 Automatic Shoe Shining Machine Two rotter shoe shine 2
7 Printer Any INKJET / LASER 1
8 Television 21" or 29" As per requird 1
19
ANNEXURE- II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT& MACHINERY (DESIRABLE EQUIPMENTS / HAND TOOLS)
NAME OF COURSE :- DIPLOMA IN HOTEL OPERATION
NAME OF LABORATORY :- COMPUTER APPLICATION
Sr.No Name of Equpt./Machinery Technical specification Minimun Remark
Qtty/Nos if any
Required
1 Computers P - 4 with Multi Media with Combo Drive 20
20
ANNEXURE- II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT& MACHINERY (DESIRABLE EQUIPMENTS/HAND TOOLS)
NAME OF COURSE :- DIPLOMA IN HOTEL OPERATION
NAME OF LABORATORY :- FOOD & BAVERAGE
Sr.No Name of Equpt./Machinery Technical specification Minimun Remark
Qtty/Nos if any
Required
1 Fork (All Purpose) 7" SS made (ie stailness steel) 36
2 Service Fork 8 -9" SS made 24
3 Spoons (All Purpose) 7" SS made (ie stailness steel) 60
4 Service Spoon 8 -9" SS made 20
5 Knife (All Purpose) 8" SS made 40
6 Dessert Spoon 7" SS made (ie stailness steel) 20
7 Tea Spoons 5 -6" SS made 20
8 Coffee Spoons 5 -6" SS made 20
9 Tongs Supporting Tool 10
10 Entiree Lenth 18 -20 cm SS made 20
11 Soup Spoon 7" SS made (ie stailness steel) 12
12 Steak Knife 8" SS made 12
21
13 Fish Knife 8" SS made 12
14 Fish Fork 8" SS made 12
15 Butter Dish & Butter Knife 18 -20 cm SS made 5
16 Quarter Plate 6" Dia Meter Fine Bone China 60
17 Tea Cup 150 ml Fine Bone China 24
18 Cofee Cup 50 ml Fine Bone China 24
19 Saucer 6" Dia Meter Fine Bone China 24
20 Dinner Plate 10" Dia Meter Fine Bone China 36
21 Sugger Bowl Supporting Tool 24
22 Soup Bowl 325 ml Fine Bone China 24
23 High Ball Glasses 150 ml Fine Glass 36
24 Tom Collins 420 ml Fine Glass 36
25 Wine Glasses (White) 240 ml Fine Glass 24
26 Red Wine Glasses 240 ml Fine Glass 24
27 Brandy Ballon 240 ml Fine Glass 12
28 Liqueur Glasses 60 ml. Fine Glass 12
29 High Ball Glasses 360 ml Fine Glass 24
30 Martini 180 ml Fine Glass 12
31 Beer Mug 325 ml Fine Glass 12
32 Salver 12" in Dia Meater 5
33 Breakfast Tray 18" in Dia Meater 5
34 Restaurant Tables for four person 3' x 3' Teak Wood made with finish polish 10
35 Restaurant Chairs Full Heigt of chair 3 ft. , Height till the seat 40
1 & 1/2 ft., Back rest 1 & 1/2 ft. , Seat 1 &
1/2 X 1 & 1/2
36 Table Cloths 4' x 4' ft. Cotton made 20
37 Naperons Supporting Tool 20
38 Bread Basket 20 - 22cm Lenth Bamboo Made 10
39 Cocktail Shaker 0.5 ltr, or 1 ltr with SS made 2
40 Bar Counter Made according to as per space available 1
23
79 Cruete set-pepper and salt As per required 5
80 Coffee pots- As per required 10
81 Finger bowls As per required 24
82 Milk jugs- As per required 24
83 Menu stands As per required 12
84 Sauce boats- As per required 10
86 Sugar bowls Hand Tool 10
87 Tea strainer Hand Tool 8
88 Toast rack Hand Tool 6
89 Water jugs- 6 Water Glass Capicity with SS OR Brass 10
made
90 Brandy balloon 240 ml Fine Glass 10
91 Champagne flute 240 ml Fine Glass 10
92 Champagne saucer 180 ml Fine Glass 10
93 Tulip Glass 270 ml fine Glass 10
94 Beer Goblet 325 ml Fine Glass 20
96 Port glass 120 ml Capacity with Fine Glass made 10
97 Sherry glass 120 ml Capacity with Fine Glass made 10
98 Whisky saucer 180 ml Fine Glass 10
99 Cocktail glasses 120 ml Capacity with Fine Glass made 10
100 Ashtray As per required 8
102 Carving knife Hand Tool 1
103 Carving Board Hand Tool 2
104 Corn on the cob holder As per required 3
105 Fruit stand As per required 2
106 Pepper mill Hand Tool 2
107 Plate cover Hand Tool 20
24
MAHARASHTRA STATE BOARD OF
TECHNICAL EDUCATION, MUMBAI
1 Bakery 1
4 Computer Lab 5
6 Bakery 10
9 Computer Lab 13
Minimum
Remark if
Sr. No. Name of Equpt. / Machinery Technical Specifications Qtty./Nos
any
required
1 Fridge S. S. 5º C 1
2 Salamander S. S. Medium size 1
3 Double deck oven S. S. Body 1
4 Gas Range (02 Burner) 1
5 S. S. Sink with Tap 1
6 Exhaust Fan 2
7 Insecticutor (Insect trap) 1
for storage
8 S. S. Rack (05 Rack) 1 of tools &
equipments
for storage
9 S. S. Almirah 1 of Raw
materials
10 Moulds Different shaper & sizes 1 Set
11 Cutters Different shaper & sizes 1 Set
12 Nozzles and piping bags 1 set each
13 Trays Baking 10 Nos -
14 Cake Stand 1
Page 3
ANNEXURE - I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Essential Equipment/Hand Tools)
(Required For Conducting The Practicals)
Minimum
Remark if
Sr. No. Name of Equpt. / Machinery Technical Specifications Qtty./Nos any
Required
for food
1 S. S. work Table 2' x 4' 1
processor
with 4
S. S. Work Station with Gas
2 2' x 5' 10 burner Gas
Stove
Stove
3 Deep Fridge S. S. Body- -18º to -23º 1
As used in
4 Hot Plate S. S. Body, electric operated 4
Ship's Galley
with
5 S. S. Sink with Tap 3 drainged
board
6 Kitchen Towel Stand 1
7 Exhaust Fan 2
8 Insecticutor 2
9 S. S. Sink (Hand Wash) 1
10 Fire Blanket 1
Wooden Locker (for students as
11
per strength)
12 Fire Extingusher 1
13 Paper Napkin Holder 1
14 Chopping Board Fiber or Wooden 11
15 Wooden Spoon 12
16 S. S. Container 8" Diameter 10 with Lid
17 Juice Stainer 10
18 Colander S. S. 8'' Diameter 10
19 Potato Masher S. S. 10
20 Grate S. S. 10
21 Rolling Pin Wooden 10
22 Oil Dishpenser S. S. 250 ml capacity 10
23 Wire Whisk S. S. Medium Size 10
24 Tong S. S. 10
25 Slicer S. S. Heavy Duty 10
26 Perforted Spoon S. S. Heavy Duty 10
27 Flat Spoon S. S. Medium Size 10
28 Rice Spoon S. S. Medium Size 10
29 Ladles (different sizes) S. S. (2 sizes Oval & Round) 10 each
30 Friying Pan Commercial 10
Page 4
ANNEXURE - I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Essential Equipment/Hand Tools)
(Required For Conducting The Practicals)
Page 5
Mock up of Guest Bathroom
with Wath Basin Counter,
24 1 Each
WC, Bath tub, Mirror and
Guest Supplies
BUNKER BED
1 Single Beds & Mattress 81" x 30" 2 Bunker type
2 Writing Table As per Lab size 1
3 Chair As per Lab size 1
4 Cupboard As per Lab size 1
5 Shower Curtain 1
6 Stainless Steel Glass 1
7 Toilet Rolls 2
8 Wall Hangings 4
9 Pillows/Pillow Slips 2
10 Blankets 2
11 Single Bed Sheets 4
12 Nightspread 2
MOCK LAUNDRY SET UP
1 Cupboard with Racks 1
2 Ironing Board 12" x 42" 1 Upholstered
3 Ironing Table 1 Upholstered
4 S. S. Working Table 1
5 Linen Cart 2 with wheels
6 Washer Extractor / Dryer 1
7 Table 2
8 Chairs 2
ELECTRICAL EQUIPMENTS
1 Wet and Dry Vaccum Cleaner 22 Ltrs 1
2 Scrubbing Machine 1
Page 6
ANNEXURE - I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Essential Equipment/Hand Tools)
(Required For Conducting The Practicals)
Minimum
Name of the Machinery/ Remark if
Sr. No. Technical Specifications Qtty./Nos
Equipment any
Required
Computers (One with
1 15
CDR/CDRW)
2 Computer Tables 15
3 Printer 1
4 LAN Networking -
Page 7
ANNEXURE - I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Essential Equipment/Hand Tools)
(Required For Conducting The Practicals)
Minimum
Name of the Machinery/ Remark if
Sr. No. Technical Specifications Qtty./Nos
Equipment any
Required
Wooden Table (Square) 4
1 3'x3' 5
seater
2 Side Board As per Restaurant size 1
Dining Chairs (Wooden
3 As per Restaurant size 20
Upholstered)
Bar Counter with water supply
4 As per Restaurant size 1
and sink
5 Back Bar Display Unit As per Restaurant size 1
6 Bar Stools 3
7 Mini Refrigerator 1
8 Cocktail Mixer (Electric) 1
9 Table cloths As per Table size 10
10 Baize cloth As per Table size 5
11 Hot case 1
12 Slip cloth 10
13 Napkins 20
Hand Tools
Cutlery 20
1 All purpose knife 20
2 All purpose fork 20
3 All purpose spoon 20
4 Fish knife 20
5 Fish fork 20
6 Service spoons 20
Page 8
7 Service forks 20
8 Dessert spoons 20
9 Dessert forks 20
10 Soup spoons 20
11 Soup bowls 5
12 Butter knife 20
13 Tea spoons 20
14 Coffee spoons 20
15 Ice cream Spoons 20
16 Fruit knife 20
17 Fruit fork 20
18 Pastry fork 5
19 Pastry tongs 1
20 Gateaux slicer 5
21 Jam spoon 1
22 Zester 1
23 Wine cradle 2
24 Peg measure 2
25 Citrus squeezer 2
26 Chopping board 1
27 Cocktail shaker 1
28 Hawthorne strainer
Crockery 20
1 Large plates 20
2 Half plates 20
3 Quarter plates 20
4 Soup cups with saucers 20
5 Cereal bowl 20
6 Tea cups with saucers 20
7 Demitasse cups with saucers 20
8 Consomme cups 20
9 Egg cups 5
10 Ashtrays 5
11 Bud vases 5
12 Cruet sets 5
13 Chutney bowls 10
14 Salad bowls
Page 9
Hollowware & Flatware 10
1 Water jugs 20
2 Water tumblers 5
3 Teapot ( 2 portions) 5
4 Teapot (4 portions) 5
5 Milkpot (2 portions) 5
6 Milkpot (4 portions) 5
7 Hot water jug 5
8 Coffee pot ( 2 portions) 5
9 Coffee pot ( 4 portions) 5
10 Creamer 5
11 Sugar bowls 5
12 Butter dishes 20
13 Ice cream cups 20
14 Finger bowls 5
15 Menu stand 5
16 Sauce boat 5
17 Tea strainer slop basin 5
18 Tooth pick holder 5
19 entrée dish ( 2 portion) 5
20 entrée dish (4 portion) 5
21 entrée dish (6 portion) 5
22 Oval Platter (2 portion) 5
23 Oval Platter (4 portion) 5
24 Oval Platter (6 portion) 5
25 Restaurant Tray (Small) 5
26 Restaurant Tray (Medium) 1
27 Ice Bucket with tongs 5
28 Sugar tongs 5
29 Toast Racks 5
30 Restaurant Salver
Page 10
Glassware 20
1 High Ball 20
2 Water Goblets 20
3 Juice Glasses 20
4 Tom Collins 5
5 Decanter 5
6 Coffee Carafe 20
7 Beer Goblets 20
8 Beer Mugs 20
9 White Wine Glass 20
10 Red Wine Glass 20
11 Champagne Tulip 20
12 Champagne Saucer 20
13 Cocktail Glass 20
14 Brandy Balloon 20
15 Roly Poly 20
16 Old Fashion Glass
Common Equipment 1
1 Water Cooler 5
2 S. S. Large Restaurrant Tray 5
3 S. S. Medium Restaurant Tray 5
4 S. S. Small Restaurant Tray 5
5 Beverage Round (Medium) 5
6 Beverage Round (Small) 5
7 Bread Basket
Page 11
ANNEXURE - II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
Minimum
Remark if
Sr. No. Name of Equpt. / Machinery Technical Specifications Qtty./Nos
any
required
NO DESIRED EQUPMENTS
Page 12
ANNEXURE - II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Desired Equipment/Hand Tools)
(Optional Equipments)
Minimum
Name of the Equipment / Remark if
Sr. No. Specifications Qtty/Nos. any
Machinery
Required
1 Dish Washer 1
2 Exhaust Fan (Small) ISI Mark 1
3 Geyser 1
4 S. S. Sink 1
5 S. S. Rack (03 shelf) 2
6 S. S. Crockery Stand 1
7 3 Bin Sink with tap 1
8 Cleaning Chemicals -
Page 13
ANNEXURE - II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Desired Equipment/Hand Tools)
(Optional Equipments)
Minimum
Name of the Equipment / Remark if
Sr. No. Specifications Qtty/Nos. any
Machinery
Required
Display on
1 Toilet Brush 1
Board
Display on
2 Window Washer 1
Board
Display on
3 Wash Basin Brush 1
Board
Display on
4 Floor Brush 1
Board
Display on
5 Scrub Pad 1
Board
Display on
6 Table Cleaning Brush 1
Board
Display on
7 Cleaning Duster 1
Board
Display on
8 Floor Broom 1
Board
Display on
9 Floor Mop 1
Board
Display on
10 Floor Mop with Wiper 1
Board
Display on
11 Cleaning Broom 1
Board
Display on
12 Carpet Brush 1
Board
Display on
13 Air Pump 1
Board
Display on
14 Glass Wiper 1
Board
Display on
15 Toilet Brush with Stand 1
Board
Page 14
ANNEXURE -II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Desired Equipment/Hand Tools)
(Required For Conducting The Practicals)
Minimum
Name of the Machinery/ Remark if
Sr. No. Technical Specifications Qtty./Nos
Equipment any
Required
NO DESIRED EQUIPMENTS
Page 15
ANNEXURE - II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERIES (Desired Equipment/Hand Tools)
(Optional Equipments)
Minimum
Name of the Equipment / Remark if
Sr. No. Specifications Qtty/Nos. any
Machinery
Required
Special Equipment
1 Soup Tureen (single portion) 20
2 Hors d' oeuvre Tray 5
3 Wine Bucket Stand 1
4 Nut Cracker 1
5 Pepper Mill 1
6 Nutmeg Grater 1
7 Bar Spoon 1
8 Ice Pick 1
9 Optic Measure 1
10 Check Flow Pourer 1
11 Push - up Measure Pourer 1
12 Ice Cream Scoop 1
13 Wine Rack 1
14 Hydrometer 1
15 Avacado Dish 1
16 Asparagus Plate 1
17 Asparagus Tong 1
18 Egg Dish 1
19 Fish Dish 1
20 Oyster Dish / Plate 1
21 Oyster Fork 1
22 Snail Dish 1
23 Snail Fork 1
24 Snail Tong 1
25 Parfait Spoon 1
26 Cheese Knife 1
27 Grape Fruit Knife 1
28 Grape Fruit Spoon 1
29 Lobster Cracker 1
30 Lobster Pick 1
31 Corn on the cob holder 1
32 Grape scissors 1
33 Caviar Knife 1
34 Fondue Fork / Dish 1
35 Carving Set 1
36 Cheese Board 1
37 Skewers 20
Page 16
38 Oil and Vineger Cruet 5
39 Fruit Basket 5
40 Gateaux Stand 1
41 Waiters Friend 5
42 Angel's wings 5
43 Crown cap opener 20
44 Can opener 5
45 Ice Shaver 1
46 S. S. Funnel 1
47 S. S. Bar mixing glass 1
48 Swizzle stick -
49 Muddler 1
50 Cocktail Sticks -
51 Cash Register 1
52 Service Counter 1
53 Tea / Coffee Dispenser 1
54 Cooking Range 1
55 Refrigerator 1
56 Deep Freezer 1
57 Salamander 1
58 Microwave Oven 1
59 Menu Display Board 1
Cupboard for Storage of Cutlery
60 1
& Crockery
61 Waste Bins 5
62 Soup Dispenser 1
63 Coffee Machine 1
64 Flambe Trolley 1
65 Flambe Pan 1
66 Rechaud Battery 1
67 Juice Extractor 1
68 Plate Warmer 1
69 Gueridon Trolley 1
70 Wine / Liquor Trolley 1
Dessert & Hors d' oeuvre
71 1
Trolley
72 Carving Trolley 1
73 Mirror Buffet Display 1
74 Wine cooler 1
75 Ice flake machine 1
76 Glass chilling cabinet 1
77 Ice cube machine 1
78 Bottle cooler 1
79 Cocktail blender 1
80 Mixer blender 1
Page 17
MAHARASHTRA STATE BOARD OF
TECHNICAL EDUCATION, MUMBAI
1
INDEX
Sr. Essential Equipments Page No.
No
1 Front Office 1
2 House Keeping 3
Desirable Equipments
3 Front Office 6
4 House Keeping 7
2
ANNEXURE- I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT& MACHINERY (ESSENTIAL EQUIPMENTS/HAND TOOLS)
NAME OF COURSE :- POST GRADUATE DIPLOMA IN
FRONT OFFICE MANAGEMENT & TOURISM
NAME OF LABORATORY :- FRONT OFFICE
Sr. Name of Equpt./Machinery Technical specification Minimun Remark if any
No Qtty/Nos
Required
1 Receptation Desk with Key & Mail H+38" to 42 width 30" 1
Rack
2 Dummy Telphone Supporting Tool 3
3 Computers P-4 2
4 Credit Card Inpriter Dummy Supporting Tool 2
5 Lobby Desk According to the size of the Lab 1
3
14 Ashtrays Hand Tool 2
4
* Different formats to be used as per topics releated to Front Office
5
ANNEXURE- I
20 Bed Lamp 1
6
21 Writing Table L x W x H - 2' x 1.1/2' x 2.1/2' 1
41 Bath Mat 30 x 60 cm 2
7
Different format to be used for practicals related to topics of House Keeping
8
ANNEXURE- II
9
ANNEXURE- II
10
MAHARASHTRA STATE BOARD OF
TECHNICAL EDUCATION, MUMBAI
HOUSE KEEPING
(HK)
Desirable Equipments
1 House Keeping 6
2 Hotel Engineering 7
ANNEXURE- I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT& MACHINERY (ESSENTIAL EQUIPMENTS/HAND TOOLS)
NAME OF COURSE DEPARTMENT :- POST GRADUATE DIPLOMA IN HOUSE KEEPING
NAME OF LABORATORY :- HOUSE KEEPING
Sr.No Name of Equpt./Machinery Technical specification Minimun Remark if
Qtty/Nos any
Required
1 Buckets Hand Tool 10
2 Mugs Hand Tool 10
3 Dust Pan Hand Tool 10
4 Hard Brooms Hand Tool 10
5 Soft Brooms Hand Tool 10
6 Wall Broom Hand Tool 5
7 Scrubers Hand Tool 10
8 Mop with different Mop Heads Hand Tool 10
9 Dust Bins Hand Tool 10
10 Carpet Brush Hand Tool 5
18 Single Bed with Head Board 3ft x 6ft x 11/2 ft with wooden made 2
20 Bed Lamp 1
41 Bath Mat 30 x 60 cm 1
13 Indicators 10 No
16 Tube Starter 15 No
27 Ceiling Rose 06 No
28 Angle Holder 06 No
29 Sockets (5 in 1) 05 No
HOSPITALITY MANAGEMENT
(HP)
Desirable Equipments
3 Management Information 4
System
4 Principle of Customer Care 5
ANNEXURE- I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT& MACHINERY (ESSENTIAL EQUIPMENTS / HAND TOOLS)
NAME OF COURSE :- POST GRADUATE DIPLOMA IN HOSPITILITY
NAME OF LABORATORY :- MANAGEMENT INFORMATION SYSTEM
Sr.No Name of Equpt./Machinery Technical specification Minimun Remark if any
Qtty/Nos
Required
1 Computers P - 4 with Multi Media with Combo Drive 10
3 Computers P-4 2
3 Printer Laser 2
4 A/C 1.5 Ton 1
5 Compact Disks 750 mb 100
6 Flooy Disk 1.44 mb 50
7 Scanner 2400 dpa 1
8 Computer Table As per required 20
Min. Qtty
Sr.No. Name of Equipment Technical Specification /Nos. Remark
Binocular Microscope Eye pices (10X, 5X ) Objectives
1 (4X,10X,40X,100X) Advances 5
Research
Incubator (Bacteriological) 60X60X60 inch., Digital Control,
2 1
Inner cabinate Stainless steel(S.S.)
Hot Air Oven 45X45X45 inch., Digital Control,
Safty Valve
Water Bath Stainless steel(S.S.) Temprature Shared with
Min. Qtty
Sr.No. Name of Equipment Technical Specification /Nos. Remark
Binocular Microscope Eye pices (10X, 5X ) Objectives Shared with
1 (4X,10X,40X,100X) Advances 0 Microbiology
Research Lab
Incubator (Bacteriological) 60X60X60 inch., Digital Control, Shared with
2 0 Microbiology
Inner cabinate Stainless steel(S.S.) Lab
Hot Air Oven 45X45X45 inch., Digital Control, Shared with
Inner cabinate Stainless steel(S.S.)
3 0 Microbiology
Temprature range 0 0C-3000C,
Safty Valve Lab
Water Bath Stainless steel(S.S.) Temprature
4 range 00C-1100C, Thermostate, 1
Size min. 6 holes
5 Hot Plate Temprature range 00C-1000C, 2
Auto Clave 30X50 inch., Stainless steel(S.S.) Shared with
6 Temprature range 0 0C-3000C, 0 Fermentation
Safty Valve, Pressure Lab
Laminar Air Flow 2X2X2 feet, Digital Control, Inner Shared with
cabinate Stainless steel(S.S.),
7 0 Microbiology
Filters Prefilter& HEPA filters,
U.V. Light tube Lab
8 Magnetic Stirrer 500ml capacity, 230V, 50Hz, AC 3
amplifire with controler
9 pH meter 3 1/2 Digital LED display, 3
oprating temp. 10-500c
10 Water Analysis Kit 3 1/2 Digital LED display, 1
oprating temp. 10-500c, covering
parameters pH-Conductivity-
Salinity
11 Photo folorimeter 0-100% transmission.With filters 1
of 0.332nanometer
12 Hand pH meter Range 0-14pH With Battery 1
backup
13 Refrigerator 425cc, 500 Lit. 1
14 Polorimeter 1
15 Analytical Balances Range 0.001-200gms 1
16 Centre fuse Capacity-8 tubes, 6000rpm With 1
Timer
17 Chromatogrphy Chamber 1
18 Shaker 20-25 flask Capacity, Digital 1
control
19 Hand Refractometer Briks 0-320 5
20 Muffle Furnace 9X4X4 inch. Outer MS Jacet 1
21 Kjeldas Distillation Unit Capcity 1lit 6
22 Markham's Still 1liter capacity with condenser and 2
Ice bath
23 Brix Hydrometer 0-10 brix 4
24 Brix Hydrometer 10-20 brix 4
25 Brix Hydrometer 20-30 brix 4
26 Wine fermentor 100lits 2
27 Heating Mentol 0
0-100 c 4
28 Test tube holders Woddden handle 10
29 Pipette Stand Plastic with various capacity 10
30 Burette Stand 20
31 Pipette pump 10
32 Pasture pipette Plastic 100
33 Thermometer 0-1000c 10
34 Wine Screw Weter choise, Butterfly, normal 5
Min. Qtty
Sr.No. Name of Equipment Technical Specification /Nos. Remark
Binocular Microscope Eye pices (10X, 5X ) Objectives
1 (4X,10X,40X,100X) Advances 5
Research
Incubator (Bacteriological) 60X60X60 inch., Digital Control, Shared with
2 0 Microbilogy
Inner cabinate Stainless steel(S.S.) lab
Hot Air Oven 25X25X25 inch., Digital Control,
Inner cabinate Stainless steel(S.S.)
3 1
Temprature range 0 0C-3000C,
Safty Valve
Water Bath Stainless steel(S.S.) Temprature Shared with
0 0
4 range 0 C-110 C, Thermostate, 0 Wine Tech.
Size min. 6 holes lab
5 Hot Plate Temprature range 00C-1000C, 1
Auto Clave 30X50 inch., Stainless steel(S.S.)
No Desired Equipments
ANNEXURE-II
Minimum
Qty/Nos.
Sr.No. Name of Equipment Technical Specification Reqd Remark
pH meter 3 1/2 Digital LED display, 3
1
oprating temp. 10-50 0c
Water Analysis Kit 3 1/2 Digital LED display, 1
0
oprating temp. 10-50 c, covering
2
parameters pH-Conductivity-
Salinity
Photo folorimeter 0-100% transmission.With filters 1
3
of 0.332nanometer
Hand pH meter Range 0-14pH With Battery 1
4
backup
5 Sectiers for Pruning Special for Grape vine 30
6 Knifes Special for Grape vine 10
7 Tractor 1
8 Small Tractor Spraying 1
9 Cultivetor Attachment with Tractor 1
10 Plaugh Attachment with Tractor 1
Min. Qtty
Sr.No. Name of Equipment Technical Specification /Nos.Reqd Remark
Binocular Microscope Eye pices (10X, 5X ) Objectives
1 (4X,10X,40X,100X) Advances 5
Research
Incubator (Bacteriological) 60X60X60 inch., Digital Control,
2 1
Inner cabinate Stainless steel(S.S.)
Hot Air Oven 45X45X45 inch., Digital Control,
Safty Valve
Water Bath Stainless steel(S.S.) Temprature Shared with
Min. Qtty
Sr.No. Name of Equipment Technical Specification /Nos.Reqd Remark
Binocular Microscope Eye pices (10X, 5X ) Objectives Shared with
1 (4X,10X,40X,100X) Advances 0 Microbiology
Research Lab
Incubator (Bacteriological) 60X60X60 inch., Digital Control, Shared with
2 0 Microbiology
Inner cabinate Stainless steel(S.S.) Lab
Hot Air Oven 45X45X45 inch., Digital Control, Shared with
Inner cabinate Stainless steel(S.S.)
3 0 Microbiology
Temprature range 0 0C-3000C,
Safty Valve Lab
Water Bath Stainless steel(S.S.) Temprature
4 range 00C-1100C, Thermostate, 1
Size min. 6 holes
5 Hot Plate Temprature range 00C-1000C, 2
Auto Clave 30X50 inch., Stainless steel(S.S.) Shared with
6 Temprature range 0 0C-3000C, 0 Fermentation
Safty Valve, Pressure Lab
Laminar Air Flow 2X2X2 feet, Digital Control, Inner Shared with
cabinate Stainless steel(S.S.),
7 0 Microbiology
Filters Prefilter& HEPA filters,
U.V. Light tube Lab
8 Magnetic Stirrer 500ml capacity, 230V, 50Hz, AC 3
amplifire with controler
9 pH meter 3 1/2 Digital LED display, 3
oprating temp. 10-500c
10 Water Analysis Kit 3 1/2 Digital LED display, 1
oprating temp. 10-500c, covering
parameters pH-Conductivity-
Salinity
11 Photo folorimeter 0-100% transmission.With filters 1
of 0.332nanometer
12 Hand pH meter Range 0-14pH With Battery 1
backup
13 Refrigerator 425cc, 500 Lit. 1
14 Polorimeter 1
15 Analytical Balances Range 0.001-200gms 1
16 Centre fuse Capacity-8 tubes, 6000rpm With 1
Timer
17 Chromatogrphy Chamber 1
18 Shaker 20-25 flask Capacity, Digital 1
control
19 Hand Refractometer Briks 0-320 5
20 Muffle Furnace 9X4X4 inch. Outer MS Jacet 1
21 Kjeldas Distillation Unit Capcity 1lit 6
22 Markham's Still 1liter capacity with condenser and 2
Ice bath
23 Brix Hydrometer 0-10 brix 4
24 Brix Hydrometer 10-20 brix 4
25 Brix Hydrometer 20-30 brix 4
26 Wine fermentor 100lits 2
27 Heating Mentol 0
0-100 c 4
28 Test tube holders Woddden handle 10
29 Pipette Stand Plastic with various capacity 10
30 Burette Stand 20
31 Pipette pump 10
32 Pasture pipette Plastic 100
33 Thermometer 0-1000c 10
34 Wine Screw Weter choise, Butterfly, normal 5
Min. Qtty
Sr.No. Name of Equipment Technical Specification /Nos. Remark
Binocular Microscope Eye pices (10X, 5X ) Objectives
1 (4X,10X,40X,100X) Advances 5
Research
Incubator (Bacteriological) 60X60X60 inch., Digital Control, Shared with
2 0 Microbilogy
Inner cabinate Stainless steel(S.S.) lab
Hot Air Oven 25X25X25 inch., Digital Control,
Inner cabinate Stainless steel(S.S.)
3 1
Temprature range 0 0C-3000C,
Safty Valve
Water Bath Stainless steel(S.S.) Temprature Shared with
0 0
4 range 0 C-110 C, Thermostate, 0 Wine Tech.
Size min. 6 holes lab
5 Hot Plate Temprature range 00C-1000C, 1
Auto Clave 30X50 inch., Stainless steel(S.S.)
No Desired Equipments
ANNEXURE-II
Minimum
Sr.No. Name of Equipment Technical Specification Qty Remark
/Nos.Reqd
1 Calorimeter With all metal filters 1
2 Spectrophoto Meter With all metal filters 1
Shaker Cum Incubetor 20-25 flask Capacity, Digital
3 1
control, Temp. Range 00c-600c
4 Fermentor Lab scale at least 100lits, with 3
Pressure sensor, temprature
control and digital display
MAHARASHTRA STATE BOARD OF
TECHNICAL EDUCATION, MUMBAI
PAPER TECHNOLOGY
(PP)
1 Chemical Laboratory 1
3 Production Laboratory 8
(Desired Equipments)
3 Production Laboratory 13
ANNEXURE-1
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
Page 3
ANNEXURE-I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERY (Essential Equipments/hand Tools)
( Required for conducting practicals)
1 Name Course/Department- Post Diploma In Paper Technology Technology
Page 4
ANNEXURE-1
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERY(Essential Equipments/hand Tools)
(Required for Conducting the Practicals)
1 Name Course/Department- Post Diploma In Paper Technology
Page 5
6 Tearing Strength Apparatus With standard 'B' pendulum 1
pneumatic clamping of the
test pieces, automatic
calculations through
Microprocessor and
presentation of measured
value, all of which ensure
accurate and stable test
results.
Interchangeable pendulum
for different range.0-2000, 0-
8000, 0-32000 mN.
Page 6
9 Cobb Tester For determining the water 1
absorbency of paper,
paperboard and similar
material. The water
absorbency of paper (the
cobb value) is defined as the
quantity of water abosrbed in
a given time by one side of a
unit area of paper or board
placed horizontally under a
head of 1cm of water.
10 Brightness Tester For electronically measuring 1
and digitally presenting the
Brightness, Opacity and
Gloss of the paper and other
similar material by angular
reflectance (Photovolt Type)
Made with imported optical.
Page 7
13 Opacity Tester For Plastic film, paper, 1
semitransparent and opaque
materials
Measurement System Visible
light source, Photoelectric
detector, Measurment Range
0 to 100 Opacity Units
Specimen Opening 30 mm x
50 mm, Measurement Area
20 mm x 40 mm, Resolution
1.0 Opacity Units
14 Couch Roll 10 kg, Stainless steel with 1
nickel chrom polish
Page 8
ANNEXURE-1
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERY(Essential Equipments/hand Tools)
(Required for Conducting the Practicals)
1 Name Course/Department- Post Diploma In Paper Technology
Page 9
ANNEXURE-1
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERY(Essential Equipments/hand Tools)
(Required for Conducting the Practicals)
1 Name Course/Department- Post Diploma In Paper Technology
Page 10
7 CylinderMould Machine Model scaled down model of 1
convinient size to illustrate
all the featurs of Cylinder
Mould paper / board making
machine
8 Digester 1 kg, stainless steel, with 1
suitable lid, inlet & outlet for
steam, elctrically heated
9 Water Screen 7/8",1/2",1/4"(Rectangular) 1 each
Page 11
ANNEXURE-I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERY (Essential Equipments/hand Tools)
(Required for conducting practicals)
1 Name Course/Department- Post Diploma In Paper Technology Technology
Page 12
ANNEXURE-II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERY(Desirable Equipments/hand Tools)
(Opional Equipment)
1 Name Course/Department- Post Diploma In Paper Technology
Page 13
ANNEXURE-II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERY (Desired Equipments/hand Tools)
(Optional Equipment)
1 Name Course/Department- Post Diploma In Paper Technology Technology
Page 14
ANNEXURE-II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERY (Desired Equipments/hand Tools)
(Optional Equipment)
1 Name Course/Department- Post Diploma In Paper Technology Technology
Page 15