CLC5957 12-Bit, 70 MSPS Broadband Monolithic A/D Converter: General Description Features
CLC5957 12-Bit, 70 MSPS Broadband Monolithic A/D Converter: General Description Features
April 2002
CLC5957
12-Bit, 70 MSPS Broadband Monolithic A/D Converter
General Description Features
The CLC5957 is a monolithic 12-bit, 70MSPS analog-to- n 70MSPS
digital converter. The device has been optimized for use in n Wide dynamic range:
IF-sampled digital receivers and other applications where — SFDR: 74dBc
high resolution, high sampling rate, wide dynamic range, low — SFDR with dither: 85dBFS
power dissipation, and compact size are required. The — SNR: 67dB
CLC5957 features differential analog inputs, low jitter differ- n IF sampling capability
ential universal clock inputs, a low distortion track-and-hold n Input bandwidth = 0-300MHz
with 0-300MHz input bandwidth, a bandgap voltage refer- n Low power dissipation: 640mW
ence, data valid clock output, TTL compatible CMOS (3.3V
n Very small package: 48-pin TSSOP
or 2.5V) programmable output logic, and a proprietary 12-bit
multi-stage quantizer. The CLC5957 is fabricated on the n Single +5V supply
ABIC-V 0.8 micron BiCMOS process. n Data valid clock output
The CLC5957 features a 74dBc spurious free dynamic n Programmable output levels: 3.3V or 2.5V
range (SFDR) and a 67dB signal to noise ratio (SNR). The
wideband track-and-hold allows sampling of IF signals to Applications
greater than 250MHz. The part produces two-tone, dithered, n Cellular base stations
SFDR of 83dBFS at 75MHz input frequency. The differential n Digital communications
analog input provides excellent common mode rejection, n Infrared/CCD imaging
while the differential universal clock inputs minimize jitter.
n IF sampling
The 48-pin TSSOP package provides an extremely small
footprint for applications where space is a critical consider- n Electro-optics
ation. The CLC5957 operates from a single +5V power n Instrumentation
supply. Operation over the industrial temperature range of n Medical imaging
-40˚C to +85˚C is guaranteed. National Semiconductor tests n High definition video
each part to verify compliance with the guaranteed specifi-
cations.
01502928
Block Diagram
01502902
01502901
Pin Descriptions
Pin Pin
Description
Name No.
Differential input with a common mode voltage of +2.4V. The ADC
AIN
13, 14 full scale input is 1.024 VPP on each of the complimentary input
AIN
signals.
Differential clock where ENCODE initiates a new data conversion
ENCODE cycle on each rising edge. Logic for these inputs are a 50% duty
9, 10
ENCODE cycle universal differential signal ( > 200mV). The clock input is
internally biased to VCC/2 with a termination impedance of 2.5kΩ.
Internal common mode voltage reference. Nominally +2.4V. Can be
used for the input common mode voltage. This voltage is derived
VCM 21 from an internal bandgap reference. VCM should be buffered when
driving any external load. Failure to buffer this signal can cause
errors in the internal bias currents.
Digital data outputs are CMOS and TTL compatible. D0 is the LSB
30–34,
D0–D11 and D11 is the MSB. MSB is inverted. Output coding is two’s
39–45
complement. Current limited to source/sink 2.5mA typical.
1–4, 8, 11, 12, 15, 19,
GND Circuit ground.
20, 23–26, 35, 36, 47, 48
+5V power supply for the analog section. Bypass to ground with a
+AVCC 5–7, 16–18, 22
0.1 µF capacitor.
+5V power supply for the digital section. Bypass to ground with a
+DVCC 37, 38, 46
0.1 µF capacitor.
NC 29 No connect. May be left open or grounded.
Data Valid Clock. Data is valid on rising edge. Current limited to
DAV 27
source/sink 5mA typical.
OUTLEV 28 Output Logic 3.3V or 2.5V option. Open = 3.3V, GND = 2.5V.
www.national.com 2
CLC5957
Absolute Maximum Ratings (Note 1) Recommended Operating
If Military/Aerospace specified devices are required, Conditions
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications. Positive Supply Voltage (VCC) +5V ± 5%
Analog Input Voltage Range 2.048 VPP diff.
Positive Supply Voltage (VCC) −0.5V to +6V
Operating Temperature Range −40˚C to +85˚C
Differential Voltage between any two < 100 mV
Grounds
Analog Input Voltage Range GND to VCC Package Thermal Resistance (Note 7)
Digital Input Voltage Range −0.5V to +VCC Package θJA θJC
Output Short Circuit Duration 48-Pin TSSOP 56˚C/W 16˚C/W
(one-pin to ground) Infinite
Junction Temperature (Note 7) 175˚C
Reliability Information
Storage Temperature Range −65˚C to +150˚C
Transistor Count 5000
Lead Solder Duration (+300˚C) 10 sec.
ESD tolerance
human body model 2000V
machine model 200V
3 www.national.com
CLC5957
Converter Electrical Characteristics (Continued)
The following specifications apply for AVCC = DVCC = +5V, 66MSPS. Boldface limits apply for TA = Tmin = −40˚C to Tmax =
+85˚C, all other limits TA = 25˚C (Note 3).
Symbol Parameter Conditions Min Typ Max Units
ANALOG INPUTS
VIN Analog Diff Input Voltage Range 2.048 VPP
Analog Input Resistance
RIN (SE) 500 Ω
(Single-Ended)
RIN (Diff) Analog Input Resistance (Differential) 1000 Ω
Analog Input Capacitance
CIN 2 pF
(Single-ended)
ENCODE INPUTS (UNIVERSAL)
Logic Input High Voltage (Note
VIH 5 V
4),(Note 5)
Logic Input Low Voltage(Note
VIL 0 V
4),(Note 5)
Differential Input Swing (Note
0.2 V
4),(Note 5)
DIGITAL OUTPUTS
VOL Logic Output Low Voltage (Note 2) 0.01 0.4 V
OUTLEV = 1 (open) 3.2 3.5 3.8 V
VOH Logic Output High Voltage (Note 2)
OUTLEV = 0 (GND) 2.4 2.7 3.0 V
TIMING (Note 6)
Maximum Conversion Rate
70 75 MSPS
(ENCODE) (Note 2)
Minimum Conversion Rate
10 MSPS
(ENCODE)
Pulse Width High (ENCODE) (Note
tP 50% threshold 7.1 ns
4)
tM Pulse Width Low (ENCODE) (Note 4) 50% threshold 7.1 ns
ENCODE falling edge to DATA not
tDNV 8.3 ns
valid (Note 4)
ENCODE falling edge to DATA
tDGV 17.8 ns
guaranteed valid (Note 4)
Rising ENCODE to rising DAV delay
tDAV 50% threshold 8.3 12.6 ns
(Note 4)
DATA setup time before rising DAV
tS tM−2.4 ns
(Note 4)
DATA hold time after rising DAV
tH tP−1.6 ns
(Note 4)
Pipeline latency 3.0 clk cycle
www.national.com 4
CLC5957
Converter Electrical Characteristics (Continued)
The following specifications apply for AVCC = DVCC = +5V, 66MSPS. Boldface limits apply for TA = Tmin = −40˚C to Tmax =
+85˚C, all other limits TA = 25˚C (Note 3).
Symbol Parameter Conditions Min Typ Max Units
POWER REQUIREMENTS
Total Operating Supply Current (Note
ICC 128 150 mA
2)
Power Dissipation (Note 2) 640 750 mW
Power Supply Rejection Ratio 64 dB
Note 1: “Absolute Maximum Ratings” are limiting values, to be applied individually, and beyond which the serviceability of the circuit may be impaired. Functional
operability under any of these conditions is not necessarily implied. Exposure to maximum ratings for extended periods may affect device reliability.
Note 2: These parameters are guaranteed by test.
Note 3: Typical specifications are based on the mean test values of deliverable converters from the first three diffusion lots.
Note 4: Values guaranteed based on characterization and simulation.
Note 5: See page 14, Figure 3 for ENCODE inputs circuit.
Note 6: CL = 7pF DATA; 10pF DAV.
Note 7: The absolute maximum junction (TJmax) temperature for this device is 175˚C. The maximum allowable power dissipation is dictated by TJmax, the
junction-to-ambient thermal resistance (θJA), and the ambient temperature (TA), and can be calculated using the formula PDmax = (TJmax – TA)/θJA. For the 48-pin
TSSOP, θJA is 56˚C/W, so PDmax = 2.68W at 25˚C and 1.6W at the maximum operating ambient temperature of 85˚C. Note that the power dissipation of this device
under normal operation will typically be about 650 mW (640 mW quiescent power + 10 mW due to 1 TTL load on each digital output). The values of absolute
maximum power dissipation will only be reached when the CLC5957 is operated in a severe fault condition (e.g., when input or output pins are driven beyond the
power supply voltages, or the power supply polarity is reversed). Obviously, such conditions should always be avoided.
5 www.national.com
CLC5957
Typical Performance Characteristics (AVCC = DVCC = +5V)
01502905 01502904
01502903 01502906
01502908
01502907
www.national.com 6
CLC5957
Typical Performance Characteristics (AVCC = DVCC = +5V) (Continued)
01502909 01502910
01502911 01502912
01502913 01502914
7 www.national.com
CLC5957
Typical Performance Characteristics (AVCC = DVCC = +5V) (Continued)
01502915
01502930
01502916 01502917
www.national.com 8
CLC5957
Timing Diagrams
015029F8
CLC5957 APERTURE DELAY Diagram
015029F9
CLC5957 ENCODE to Data Timing Diagram
015029H1
CLC5957 ENCODE to DAV Timing Diagram
015029H2
CLC5957 DAV to Data Timing Diagram
9 www.national.com
CLC5957
Single IF Down Converter (Diversity Receiver Chipset)
01502920
01502922
www.national.com 10
CLC5957
Evaluation Board
01502923
Evaluation Board Schematic
11 www.national.com
CLC5957
Evaluation Board (Continued)
01502924
CLC5957PCASM Layer 1
01502926
CLC5957PCASM Layer 2
www.national.com 12
CLC5957
Evaluation Board (Continued)
01502925
CLC5957PCASM Layer 3
01502927
CLC5957PCASM Layer 4
13 www.national.com
CLC5957
CLC5957 Applications
Analog Inputs and Bias
Figure 1 depicts the analog input and bias scheme. Each of
the differential analog inputs are internally biased to a nomi-
nal voltage of 2.40V DC through a 500Ω resistor to a low
impedance buffer. This enables a simple interface to a
broadband RF transformer with a center-tapped output wind-
ing that is decoupled to the analog ground. If the application
requires the inputs to be DC coupled, the VCM output can be
used to establish the proper common-mode input voltage for
the ADC. The VCM voltage reference is generated from an
internal bandgap source that is very accurate and stable.
015029F3
The VCM output may also be used to power down the ADC.
When the VCM pin is pulled above 3.5V, the internal bias
mirror is disabled and the total current is reduced to less than
10mA. Figure 2 depicts how this function can be used. The
diode is necessary to prevent the logic gate from altering the
ADC bias value.
015029F4
www.national.com 14
CLC5957
CLC5957 Applications (Continued)
Minimum Conversion Rate Supply voltages (J1 pins 31 A&B and 32 A&B)
This ADC is optimized for high-speed operation. The internal The CLC5957PCASM is powered from a single 5V supply
bipolar track and hold circuits will cause droop errors at low connected from the referenced pins on the Eurocard con-
sample rates. The point at which these errors cause a deg- nector. The recommended supplies are low noise linear
radation of performance is listed on the specification page as supplies.
the minimum conversion rate. If a lower sample rate is
Digital Outputs (J1 pins 7B (MSB, D11) through 18B
desired, the ADC should be clocked at a higher rate, and the
(LSB) and 20B (Data Valid))
output data should be decimated. For example, to obtain a
10MSPS output, the ADC should be clocked at 20MHZ, and The digital outputs are provided on the Eurocard connector.
every other output sample should be used. No significant The outputs are buffered by 5V CMOS latches with 50Ω
series output resistors. The rising edge of Data Valid may be
used to clock the output data into data collection cards or
logic analyzers. The board has a location for the HP
01650-63203 termination adapter for HP 16500 logic analyz-
ers to simplify connection to the analyzer.
15 www.national.com
CLC5957 12-Bit, 70 MSPS Broadband Monolithic A/D Converter
Physical Dimensions inches (millimeters) unless otherwise noted
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.