Dreamer 4K: User Manual
Dreamer 4K: User Manual
Only suitable
for age 14+
Dreamer 4K
User Manual
05 Installation
Propeller ...................................................................................................................... 03
Camera ...................................................................................................................... 04
06 Charging
07 Remote control
10 Function details
11 Specification ............................................................................................................... 19
Thank you for purchasing Potensic Dreamer 4K drone. Please read the user manual carefully and
keep it for future reference. If you need help, please contact our support team(support@poten-
sic.com)with your order number from Amazon or official website.
Potensic Dreamer 4K is equipped with an intelligent flight control system, which can realize functions
such as point of interest, intelligent follow me, and automatic return home.
With 1 / 3-inch CMOS image sensor and Electric Image Stabilization system, the drone can shoot
2.7K 30 fps video and high-definition picture with its 8.0MP camera.
Daily maintenance
Packing list
7 3
1
5
9
8
11 10
12
02
1 Camera 4 Blade 7 Damping plate
10 Smart battery
11 Power indicator
12 Power switch (after short pressing once, long press for 2 seconds to switch on/off the drone)
Installation
1. Propeller
When installing blades, pay attention to the Press down the blade in alignment with the
"CW" and "CCW" marks on the blades. central axis, and rotate.
Corresponding to the "CW" and "CCW" According to the direction marked by the
marks on arms of the drone. blade lock until it is fully screwed.After
installation, the propeller will pop up and
lock. Removal of the blades are reverse of
the above steps.
03
2. Camera
The camera has been installed at the factory and can be used after power on. But if you are replacing
the camera and install it, the installation steps are as follows:
1. Install the damping ball of the camera onto the damping plate.
2. Insert the camera power cable and steering gear cable into the connector of drone adapter plate
respectively.
3. Close the cover plate of the connecting line to complete assembly of the camera.
3. Micro SD card
Insert the micro SD card into the camera micro SD card slot. It is recommended to use branded micro
SD card products, such as SanDisk, Kingston or Samsung, requiring a micro SD card capacity of
4GB--256GB(at most). All pictures and video files will only be recorded in micro SD card, instead of
App or mobile phones. It can download to mobile phones from the App. Note: micro SD card is not
included.
04
4. Mobile phone clip
Pull the remote control pull-out board, and then put into a mobile phone. The size range of clamping:
97-178mm.
Charging
Please return in time and charge the battery when the drone in low battery. Connect the adapter
correctly as shown in the figure to charge. The indicator flashes when charging, and goes out when
fully charged. It takes about 2 hours.
Note
1. Please use the original charger to charge.
2. Do not charge on a carpet to avoid fire.
3. Recharge every 3 months to keep battery active.
4. Do not put a charged battery under high temperature, such as open fire or electric heating device,
otherwise it will be damaged or explode.
5. Do not strike or knock surface of hard objects with a battery.
6. Do not disassemble a battery.
7. Do not leave the battery alone during charging.
05
Installation and removal of battery
Figure 1 Figure 2
Note: When hearing a "click" sound, the battery is successfully installed in place.
0%~25%
25%~50%
50%~75%
75%~100%
Fully charged
Connect the Micro USB interface of the remote control to the commonly used maximum 5V/2A
charger. It takes about 2 hours to be fully charged.
06
(The plug is not included in packing list)
5V
Remote control
Dreamer 4K uses a 2.4G remote control with complete function buttons. It can support various
operations and settings of the drone and camera within a maximum communication distance of 800m,
and can display real-time HD pictures on the mobile device through PotensicPro app. The remote
control has a built-in rechargeable lithium battery, which can work continuously for up to 4 hours.
1
2
5
4 3
7
1 Antenna
Receive and send transmission signal
2 Control stick (mode 1)
07
Push the left stick up or down to control the take off or landing of the drone; push the left stick left or
right to control the drone to turn left or right; short press the middle key of the left stick to switch the
GPS mode or altitude mode of the drone.
Push the right stick up or down to control the drone going forward or backward; push the right stick left
or right to control the drone to fly left or right.
3 Power switch
Long press 2s to turn the remote control on / off.
5 One-click return
Long press 1s to return.
10
9 11
8
12
8 Control sticks storage box
A box to place your control sticks.
10 Photograph
Press to take one picture at a time.
11 Video-recording
Press once to record, and then press once to exit.
08
2. Remote control mode
There are two remote control modes of this product, i.e. mode 1 and mode 2. Mode 1 is the default
setting.
Mode 1
Downward
Backward
Mode 2
Downward
Backward
09
Drone App "PotensicPro"
Android user
Please search and download the drone App "PotensicPro" in Google Play or scan the QR code below
to download. This App is compatible with Android 5.0 and above.
For Android
iOS user
Please search and download the drone App "PotensicPro" in APP store or scan the QR code below
to download. This App is compatible with IOS 9.0 and above.
For iOS
After downloading the drone APP, it is necessary to register a personal account before using.
Fill in email - fill in password - view agreement - click register. Please log in after successful
registration. (Note: please keep your mobile phone connected with network during registration)
Turn on drone- turns on WiFi setting on mobile phone - select WiFi account "Potensic
D1_XXXXXX "- enter WiFi password "12345678"- click to connect.
Note: when log in to the App for the first time, please enter the map interface when connected to
the network to download map
10
Drone flight mode
Dreamer 4K adopts a new generation of Potensic flight control, which supports the following two
flight modes.
GPS mode: GPS module can realize precise hovering, path flight and other intelligent flight modes.
In the GPS mode, when GPS signal is no less than 6, it can be used for precise
positioning; when GPS signal is less than 6 , the drone cannot realize accurate
positioning, only provide altitude stabilization, and does not support smart flight
function.
Altitude mode: Without GPS module, it can only provides altitude stabilization. At this time, the
operator manually control flight of the drone with joystick. Beginners is not
recommended.
Operation interface
4 6 8 10
1 2 3 5 7 9
23 11
22
12
21
13
20
14
19 18 17 16 15
1 Return to the menu 6 GPS mode / altitude mode 11 Photo/ Video switch
11
16 Vertical flight speed 21 Intelligent flight mode settings
1 2 3
7 5 6
4 Circling mode
5 Waypoint mode
12
Setting interface
Flight precautions
1. Check if the remote control, smart flight battery and mobile equipment are fully charged.
2. Check if the device body is complete and the propeller is installed correctly.
3. Check if the camera works normally after power on.
4. Check if App works normally.
5. Check if Micro SD card card is inserted and make sure the camera is clean.
6. Low power protection: the low power alarm is triggered when power is less than 20%. The drone
will intelligently trigger low power return according to the distance between the current position
and home point.
7. Loss of connection protection: after losing connection for 3 seconds, one-click return will be
triggered; during return, the drone will hover if reconnect successfully.
8. Out of control protection: if the horizontal inclination angle is over 80 degrees for 0.5 seconds,
the drone will be locked automatically to protect the motor.
Figure 1
First, turn on the drone, enter the mobile phone setting option, search "Potensic D1_XXXXXX" in the
WiFi setting and connect. Then, start the mobile phone APP "PotensicPro" to enter the operation
interface.
3. Geomagnetic calibration
The first flight requires geomagnetic calibration. If drone is under geomagnetism disturbance, it may
require recalibration as follows:
Step 1: enter the PotensicPro App setting interface, click the second column, and select geomagnetic
calibration in the list. The left front light flash green and the left rear light flash red indicate
that it's ready for calibration.
Step 2: rotate the drone 720° horizontally, than the right front light flash green and right rear light flash
red. (Picture 1)
Step 3: rotate the drone 720° vertically with camera upwards. The four indicator light are solid on(the 2
front lights are green while the rear lights are red), and calibration is completed. (Picture 2)
Note: if the left front light flash green and the left rear light flash red slowly, it indicates that calibration
fails. It is recommended to recalibrate geomagnetic after changing the take-off location.
14
Figure 1 Figure 2
Function details
Take-off mode 1: push the left and right stick inwards 45 degrees(Picture 1) at the same time, unlock
the drone or click the App unlock icon , and push up the throttle lever.
Take-off mode 2: long press the "take-off and land" button for 2 seconds, there will be a short "beep"
sound, or click the icon on the App . At this time, the drone will slowly take off
and hover at a height of about 1.2 meters.
15
Figure 1
The smart return to home (RTH) function enables the drone to return to the last recorded take-off
point. This function shall be achieved in GPS mode.
There are three types of return to home (RTH): one-click return / smart low-power return / no signal
return.
*One-click return:
Remote control: long press the "HOME" button on the remote control, there will be continuous "beep"
sound, and the drone will return. Long press "HOME" button again to exit RTH automatically, and
"beep" sound disappears.
APP control:
Click the "HOME" icon on the app to start one-click return, click the icon again to cancel.
Low-power alarm: when power of the drone is less than 20%, there is continuous "beep" sound from
the remote control and the battery icon on the App flashes.
Low-power return: the drone system will automatically determine whether to return according to the
distance and battery power. When the drone returns, its four footlights remain
flashing until it lands on the ground.
Note: the drone does not have automatic obstacle avoidance function. If the drone crashes into
buildings or other obstacles on the way back, it will fall and break.
16
3. Headless mode
Note:
Before takeoff, the operator's position is very important for "headless mode". Therefore, after entering
"headless mode", please do not change operator's direction to avoid direction confusion or
unnecessary loss and damage.
Put head of the drone faces straight ahead, click headless mode icon in the App to enter headless
mode after take-off, and click again to exit.
Headless mode
The forward direction of the drone is the direction of the operator and the remote control during
take-off. Regardless of the front direction, if the operator pushes the joystick forward and backward,
the drone will fly forward and backward accordingly; if the operator pushes the joystick left and right,
the drone will fly left and right. It is very important for the operator to remain his/her position or
direction otherwise it may cause direction confusion of the drone.
17
4. Circle flight mode
5. Follow me mode
18
6. Waypoint flight mode
Specification
Drone
Maximum horizontal flight speed: 8 m/s (sport mode); 5 m/s (standard mode)
19
Camera
Remote control
Capacity: 3000mAh
Voltage: 15.2V
Battery type: Li Po 4S
Capacity: 45.6Wh
20
Charger
Frequent Q&A
Problem Solution
21
Drone Indicator Introduction
Light status 1s
Normal status From 2s
Time 1/4 1/4 1/4 1/4
Statement:
1. This product is not a toy, but a precision equipment integrating mechanical, electronic, aerodynam
ics, high-frequency emission and other professional knowledge, which requires correct assembly
and debugging to avoid accidents. The product holder should operate and control in a safe way;
improper operation may cause serious personal injury or property loss.
2. This product is suitable for people who have experience in operating model drones and older than
14 years old.
3. In case of use, operation, maintenance and other problems. Please contact the local distributor or
relevant personnel of the company.
22
Safety precautions:
Keep away from people when flying the remote-controlled drone. Improper assembly or damage to the
body, poor electronic control, and unfamiliar operation may lead to unpredictable accidents such as
drone damage or personal injury. Operators should pay attention to flight safety, and understand
responsibilities caused by negligence.
Note:
This product has been tested to meet requirements of FCC Part 15 for Class B digital products. These
regulations ensure that this product will not have a harmful impact on the residential environment
during installation and use. This product will radiate RF energy when working. If not installed and used
according to instructions, it may cause interference to wireless communication.
● However, in some specific installation and use occasions, there may be interference. Users can
determine whether interference is caused by the product by switching on and off. If this product does
interfere with wireless and video receiving equipment, users may take the following corrective
measures:
• Adjust the orientation of the receiving antenna appropriately.
• Increase distance between the product and receiving equipment
23
• Connect the device to a socket with a different circuit from the receiver.
• Seek assistance from a dealer or an experienced wireless / video technician.
● The manufacturer shall not be responsible for any wireless and video interference caused by
illegal modification of the equipment. Because these modifications and changes are beyond the
user's operation permission.
1. The package and instructions contain important information and should be properly kept.
2. It is your responsibility to ensure that this drone will not cause injury and property loss.
3. The commissioning and installation of the drone shall be carried out in strict accordance with
operation instructions. The drone shall keep a distance of 1-2 meters from users or other people
during fly to avoid the drone from colliding with heads, faces and bodies of people during fly and
landing.
4. Our company and retailers shall not be responsible for any loss, damage and human injury caused
by improper use or operation.
5. Adults should provide guidance on children when flying. Children under 14 years old are not
allowed to operate this product.
6. Please install and use correctly according to instructions or packaging requirements. Some parts
shall be assembled by adults.
7. This product contains small parts, please keep it out of reach of children to prevent dangers of
eating or suffocation.
8. It is strictly forbidden to fly on the road or in water-gathered places to avoid accidents.
9. Please put packing materials away in time to avoid casusing harm to children.
10. Do not dismantle or modify the drone, which may cause failure.
11. The battery of charger battery box shall be plugged into the specified power source as marked on
the product.
12. The remote control has a built-in lithium battery, which does not need to be replaced.
13. Use only the original charger.
14. The charger is not a toy.
15. The remote control uses a 3.7V built-in lithium battery.
16. When charging the rechargeable battery, it shall be carried out under the supervision of an adult.
When charging, it is necessary to keep away from flammable materials. The guardian should not
leave the drone outside the surveillance range during charging
17. Please do not short circuit or squeeze the battery to avoid explosion.
18. Do not mix different types of lithium batteries.
19. The drone uses a smart lithium battery, which can be recharged when plugged in or out.
20. Do not short-circuit, decompose or put the battery into a fire; do not place the battery in a high
temperature and hot place (such as in a fire or near electric heating devices).
21. The drone shall be used far away from other electrical equipment and magnetic objects to avoid
mutual interference.
22. Please keep a safe distance from propellers rotating at a high speed to avoid dangers of wringing
and cutting.
24
23. Keep the model away from ears! Misuse may cause hearing loss.
24. Please use a mirco USB 5V charger instead of higher voltage charger.
25. In order to ensure requirements for magnetic environment of the aviation radio station. The use of
model remote control shall be stopped as required within periods and areas of radio control orders
by relevant national departments.
26. Keep your drone in line of sight.
27. Don't fly in the crowd.
28. Do not fly over sports venues or events.
29. Please totally learn about airspace restrictions and requirements.
25