Professional Documents
Culture Documents
DACS1232 Lab Experiment
DACS1232 Lab Experiment
The chemistry laboratory can be a place of discovery and learning. However, by the very nature
of laboratory work, it can be a place of danger if proper common-sense precautions aren't taken.
While every effort has been made to eliminate the use of explosive, highly toxic, and carcinogenic
substances from the experiments which you will perform, there is a certain unavoidable hazard
associated with the use of a variety of chemicals and glassware. You are expected to learn and
adhere to the following general safety guidelines to ensure a safe laboratory environment for
both yourself and the people you may be working near. Students who fail to follow all safety rules
may be asked to leave the lab or suffer grading penalties.
ATTIRE
a) Safety goggles must be worn at all times while in the laboratory. This rule must be followed
whether you are actually working on an experiment or simply writing in your lab notebook.
b) Closed toe shoes and long pants must be worn in the lab. Sandals and shorts are not allowed.
c) Long hair must be tied back when using open flames.
CONDUCT
1
COMMONLY USED LABORATORY EQUIPMENT
2
GENERAL INSTRUCTIONS
a) Before starting any experiment, have a clear idea of what is to be done by studying carefully
the details of the experiment. Plan your work so as to maximize laboratory time.
b) Record all details, such as accurate weights and volumes, color changes, or evolution of gases,
on a notebook. Do not use scraps of paper to do this.
c) Keep your working bench clean and dry. Store glasswares that are not immediately required,
place dirty glasswares in a plastic bowl if they are to be cleaned later, and throw solid wastes
in the proper waste basket.
d) Carry all operations involving unpleasant and noxious materials in a properly functioning fume
cupboard.
CLEANING OF GLASSWARES
It is a good habit to clean all glasswares immediately after use as the identity of the contaminant
is known and thus easier to remove.
a) Use a test-tube brush and a commercial washing powder or liquid detergent.
b) Rinse thoroughly with tap water, and finally with distilled water. Drain off the water as
completely as possible.
c) Use a warm air blower or a hot oven (100-120oC for about 1 hour) to dry the glassware,
placing them upside down. Glassware to be used immediately may be rinsed with a little
industrial spirit or acetone before drying.
TRANSFERRING MATERIALS
a) Always bring a CLEAN, DRY container and CLEAN, DRY transfer tool with you to get any
chemicals.
b) Take the correct amount of chemical from a container but NEVER put any back once you have
taken it to your lab station.
c) Put the lid back on any chemical container when you are finished with it.
d) NEVER use the same piece of equipment or apparatus for different chemicals. Failure to do this
could result in contamination of one or more stock bottles or jars. Always start with clean, dry
containers for each separate chemical.
e) Pour liquids slowly to avoid splashing.
f) In transferring liquids from one container to another at your lab station, use a stirring rod laid
across the top of one container to direct the flow of the liquid into the other. This technique is
especially useful when you are separating a liquid from a solid (decanting).
ANALYTICAL BALANCE
Many experiments require accurate weights of solid chemicals. An analytical balance is used for
this purpose. Most laboratories are equipped with digital electronic balances and/or single pan
analytical balances. These balances are accurate to 0.001 and 0.0001 g respectively. General
rules when using an analytical balance:
a) Before weighing, make sure the reading is at zero. After weighing, press “tares” or turn
the dial so that the reading is back at zero.
3
b) Use a weighing bottle with a stopper. Do not use pieces of paper.
c) Do not weigh corrosive or hot chemicals.
d) Keep the balance clean all the time.
1. GRADUATED CYLINDERS
i. These are designed to measure volumes of liquids accurately.
ii. No chemicals are to be mixed in a graduated cylinder.
iii. A graduated cylinder should never be heated or placed in an oven.
iv. Different size graduated cylinders have different "sensitivities"; that is, different
degrees of accuracy. Selection of the proper graduated cylinder depends not only
on the total volume you need to measure but the accuracy that you need as well.
3. BURETTES
i. A burette is used like a graduated cylinder in that a specific volume can be
accurately measured.
ii. The burette is held by a ring stand and the liquid is dispensed by a small valve at
the bottom.
iii. Burettes that have not been cleaned properly are major sources of error in labs
requiring their use.
4. VOLUMETRIC FLASKS
i. These long-necked flasks are used for preparing a specific volume (e.g. 1.00 liter,
2.00 liters) of a solution. There is a single line etched on the neck for this particular
volume only.
4
5. PIPETTE
i. Pipettes are narrow, hollow tubes that are used to draw a specific, small volume of
liquid with a squeeze bulb. Typically, the capacity of a pipette is 5.0 or 10.0
milliliters.
ii. Pipettes should never be used for stirring solutions.
iii. NEVER use your mouth to draw a solution into a pipette!
5
EVALUATION OF EXPERIMENT DATA
The chemist scientist of today and future therefore needs to have thorough grounding in
experiment techniques, in how to acquire data, and in how to evaluate the data collected. Only
with knowledge of how to evaluate collected data can any significance be placed on the
experimental measurements. Precision and accuracy are two essential concepts in the evaluation of
data.
PRECISION
Precision is a quantitative measured of the reproducibility of experimental measurements how well
repeated measurements of the same quantity agree with one another. Precision is frequently
measured in terms of the average deviation, which is determined by following
a. determine the average value from a series of measurements
b. determine the deviation of each measurement from the average value
c. determine the average of the deviations without regard to sign
ACCURACY
The agreement of experimental measurements with the accepted value of a quantity is measured
in term of the error. The error is the difference between the values of quantity as measured and
the accepted value of the same quantity:
Error
Percent error x 100 %
Accepted value
EXAMPLE: in the determine of the concentrations of an unknown acid by titration with standard
base, four measurements were made: 0.1025 M, 0.1018 M, 0.1020 M, and 0.1024 M. Compute
the average value and the average deviation. Assume that the accepted value of the unknown
acid molarity is 0.1014 M as the determined by several different experienced experimenters
using sound technique. Compute the error and percent error for determination of the molarity of an
unknown acid.
SOLUTION: the average value is computed by summing the four measurements and dividing by
four. This yields an average value of 0.1022 M. the individual deviations of each measurement
from the average value are 0.0003 (0.1025 M), 0.0004 (0.1018 M), 0.0002 (0.1020 M) and
0.0002 (0.1024 M). The sum of the four deviations 0.0011, divided by four yields the average
deviation, 0.00028. Since this deviation represents an uncertainty in the measurements, the
molarity of the unknown acid is not precisely 0.1022 M, but ranges from 0.1019 M to 0.1025 M
and should therefore be reported with the average deviation included, that is 0.1022 0.0003
M.
6
Further, to make the measurement of precision more useful, the average deviations are put on the
percentage basis by determine the relative average deviation. This is the average deviation
divided by the the average value and multiplied by 100%.
Average deviation
Re altive average deviation x 100 %
Average of measuremen ts
0 . 00028
Re altive average deviation x 100 % 0 . 27 %
0 . 1022
A relative average deviation of 0.27% or better (that is, smaller) is typical expected precision
value for an acid-base titration. In general, however, the precision of an experiment varies with
the technique and/or apparatus used. A number of variables built into the method of the
experiment can affect its precision. In the method tested over long period of time, the results
(average value) should not only agree very well with one another (have good precision) but also
agree very closely with the accepted value (have high accuracy)
Since the error is the difference between the measured value and accepted value, in this case it is
0.1022 – 0.1014 = + 0.0008. From this error, the percent error is calculated.
0 . 0008
Percent error x 100 % 0 . 8 %
0 . 1014
The only significant of the sign of the error (+ or -) is that the measured value is greater or smaller
than the accepted value. In the example above, the percent error, which is measures the accuracy
of the experiment, is larger that the precision. This is an indication of existence of systematic error
and can be corrected. If all systematic errors have been eliminated, the accuracy should be
comparable to the precision of the experiment that measures random error. Thus the accuracy of
the experiment is related to the precision (random error) but is also related to possible systematic
error.
GRAPHS
Graphs are used to present the data in picture from so that they can be more readily grasped by
the reader. Occasionally a graph is used to follow a trend. Notice that the best smooth curve is
drawn through the data points. This is not the same as connecting the dots, all data points will not
fall on the line. Often, a graph is used to show how well data fit a straight line. The line drawn
may either be visually estimated.
a) The graph must have a title. Title your graph. Make sure you describe what is represented
on the horizontal and vertical axes.
b) The scale you select should be easy to work with. Such as a 1 square represents 1, 2, 5, or
10. Or perhaps 5 squares represent a unit of 1, 10, or a multiple of ten, such as 20,100,
or 0.1. Never change the scale along an axis. However, you may use a different scale for
each axis.
c) Select a scale that uses the greatest portion of the paper. Don't go overboard here. The
axes must be both numbered and labeled.
7
d) Using a ruler draw the coordinate axes on the graph paper.
e) Put "tick" marks on the axes to show the measurements.
f) Plot your points and then draw a best fit curve or line. Do not connect the dots.
UNIT OF MEASUREMENT
The International System of Units (abbreviated SI from the French Le Système international d'unités)
is the modern form of the metric system. It is the world's most widely used system of units, both in
everyday commerce and in science.
The international system of units consists of a set of units together with a set of prefixes. The units of
SI can be divided into two subsets. There are seven base units. Each of these base units is nominally
dimensionally independent. From these seven base units several other units are derived.
A prefix may be added to units to produce a multiple of the original unit. All multiples are integer
powers of ten. For example, kilo- denotes a multiple of a thousand and milli- denotes a multiple of
a thousandth hence there are one thousand millimetres to the metre and one thousand meters to the
kilometer. The prefixes are never combined: a millionth of a kilogram is a milligram not a
microkilogram.
SI derived units are part of the SI system of measurement units and are derived from the seven SI
base units
8
Derived units with special names
Physical Quantity Unit Symbol SI base units (other units)
Frequency hertz Hz s−1 (1/s)
Energy joule J m2∙kg∙s−2 (N∙m)
Force Newton N m∙kg∙s−2 (m∙kg/s2)
Pressure Pascal Pa m−1∙kg∙s−2 (N/m2)
Electric charge coulomb C A∙s
Temperature Celsius °C K (t°C = tK − 273.15)
Volume Liter L dm3 (L)
Conversion of units refers to conversion factors between different units of measurement for the
same quantity.
Mass unit
453.6 grams = 1 pound (Ib) 1 metric ton = 1000 kg
1 kilogram = 1000 gram = 2.205 pound (Ib) 1 ounce = 28.35 grams
1 gram = 1000 milligram
Volume Unit
1 liter (L) = 1000 millimeter (mL) = 1000 cm3 1 cubic foot = 28.316 L
1 milliliter (mL) = 0.001 L = 1 cm3 1 gallon = 4.546 09 L
1 liter (L) = 1 dm³ = 0.001 m³
Length unit
1 mile = 1.609 kilometer = 5280 feet 2.54 cm = 1 inch
1 meter (m) = 100 cm = 39.37 inches 1 yard = 36 inches = 0.914 m
1 millimeter = 0.001 m = 0.1 cm 1 Angstrom (Å) = 1.0 x 10-8 cm = 0.10 nm
Energy
1 joule = 107 ergs 1 colorie = 4.184 joule
9
UNIVERSITI TEKNIKAL No. Dokumen: No. Isu./Tarikh
MALAYSIA MELAKA TB/MMK/DACS 1232 1/7-7-2010
CHEMISTRY
No. Semakan/Tarikh Jumlah Mukasurat
Experiment 1: Usage and Calibrate of Lab
1/7-7-2010 3
Glassware Equipment
OBJECTIVE:
To calibrate glassware such as burette, pipette, volumetric flask, beaker, and measuring cylinder
and list possible errors that could occur in an experiment.
LEARNING OUTCOMES
After conducting this experiment, you should be able to:
1. State the reasons why laboratory equipments must be calibrated prior to use;
2. Calibrate glassware’s; e.g. burette, pipette and volumetric flasks; and
3. List the possible errors that could occur in an experiment.
INTRODUCTION:
Chemists use a variety of glassware to measure the volume of chemicals. The specific type
of glassware used in any situation depends on how accurately or precisely the volume needs to be
known. An error is a bound on the precision and accuracy of the result of a measurement.
These can be classified into two types: random error and systematic error. Random error
is caused uncertainty and carelessness in the measurement apparatus, where as systematic errors is
occur when the equipments used are imperfect or faulty and were not calibrated before use. These
errors could be minimized by checking and calibrating the equipments prior to use.
Glassware is used for a wide variety of functions which include volumetric measuring,
storing chemicals or samples, mixing or preparing solutions or other mixtures. For the burette,
pipette and volumetric flask are made to determine specific volume of a solution at a specific
temperature. Therefore, it is important to determine the type of glassware that will be used and
calibrate it. Meanwhile, there are types of glassware are used for the approximate measurement
of volume likes reagent bottles, beakers, conical flasks, and graduated cylinders. Normally they
are used to prepare solutions with an approximate concentration.
There are three general methods commonly employed to calibrate glassware. These are
as follows: Direct calibration: A volume of water delivered by a burette or pipette, or contained in
a volumetric flask, is obtained directly from the weight of the water and its density (refer to Table
1.1). Indirect calibration: Volumetric glassware can be calibrated by comparison of the mass of
water it contains or delivers at a particular temperature with that of another vessel which had
been calibrated directly. The volumes are directly related to the masses of water. This method is
convenient if many pieces of glassware are to be calibrated. Relative calibration: It is often
necessary to know only the volumetric relationship between two items of glassware without
knowing the absolute volume of either.
This experiment will acquaint you with the precision, accuracy, and tolerance of
measurements made using a beaker with calibration marks, a graduated cylinder, a burette, and a
pipette. The objective of this experiment is to determine the accuracy and precision of your
volumetric glassware, so that you can chose the proper instrument for our next analytical
experiments
10
Table 1.1: Density of Water at Various Temperatures
LAB EQUIPMENT
100 mL volumetric flask 100 mL measuring cylinder
50 mL burette analytical balance
20 mL pipette funnel
150 mL beaker dropper
100 mL beaker wash bottle
EXPERIMENTAL PROCEDURE
1. Wash, clean and dry 100 mL beaker (label A), and record its weight.
2. Clean the burette with distilled water.
3. By using funnel (avoid spilling) to pour the distilled water into the burette to a point the
mark for 0.00 volume; (make sure the portion of the burette below the stopcock is filled or
without any air bubbles).
4. Transfer 50 mL water from burette into beaker (label A).
5. Repeat step 3 and 4, by adding distilled water into beaker (label A) from burette until the
volume reaches 100 mL.
6. Record the weight of water and beaker for 100 mL volume. Calculate the density of water
(in g/mL).
7. Compare value of density was measured with standard density of water at ambient
temperature.
mass
density (eq. 1.1)
volume
8. Compare this calculated density to its actually density (via temperature) using the percent
error formula shown below:
| Theoritica l Experiment |
x 100 % % Error (eq. 1.2)
Theoretica l
11
Part B: Calibrate Pipette
1. Rinse, clean and dry the 100 mL beaker (label A) has been used, and records its weight.
2. Rinse the 20 mL pipette with distilled water.
3. Fill the pipette by using pipette bulb until the distilled water is reach pipettes level line
4. Transfer 20 mL water from pipette into beaker (label A). Withdraw the last drop of water
by touching it to the glass surface for about 15 seconds.
5. Repeat step 3 and 4, by adding distilled water into beaker (label A) from pipette until the
volume reaches 100 mL.
6. Record the weight of water and beaker for 100 mL volume. Calculate the density of water
(in g/mL).
7. Compare value of density was measured with standard density of water at ambient
temperature.
1. Rinse, clean and dry the 100 mL beaker (label A) has been used, and records its weight.
2. Rinse and clean the 100 mL volumetric flask with distilled water.
3. Pour the distilled water into the volumetric flask until approximately ½ from the marked
level by using a funnel.
4. Use a clean dropper to add the water until it reaches the required level. Position your
eyes parallel to the meniscus level.
5. Transfer 100 mL water from volumetric flask into beaker (label A).
6. Record the weight of water and beaker for 100 mL volume. Calculate the density of water
(in g/mL).
7. Compare value of density was measured with standard density of water at ambient
temperature.
1. Rinse, clean and dry the 100 mL beaker (label A) has been used, and records its weight.
2. Rinse and clean the 100 mL measuring cylinder with distilled water.
3. Pour the distilled water into the measuring cylinder until it reaches the 100 mL level.
Position your eyes parallel to the meniscus level.
4. Transfer 100 mL water from measuring cylinder into beaker (label A).
5. Record the weight of water and beaker for 100 mL volume. Calculate the density of water
(in g/mL).
6. Compare value of density was measured with standard density of water at ambient
temperature.
1. Rinse, clean and dry the 100 mL beaker (label A) has been used, and records its weight.
2. Rinse and clean the 150 mL beaker with distilled water.
3. Pour the distilled water into the beaker until it reaches the 100 mL level. Position your eyes
parallel to the meniscus level.
4. Transfer 100 mL water from measuring cylinder into beaker (label A).
5. Record the weight of water and beaker for 100 mL volume. Calculate the density of water
(in g/mL).
6. Compare value of density was measured with standard density of water at ambient
temperature.
12
UNIVERSITI TEKNIKAL No. Dokumen: No. Isu./Tarikh
MALAYSIA MELAKA TB/MMK/ DACS 1232 1/7-7-2010
OBJECTIVE:
To calculate the density of given substances from measured values of volume and mass
LEARNING OUTCOMES
After conducting this experiment, you should be able to:
1. Known that type of technique to determine the density of substance
2. Calculate the density of an unknown liquid
3. Calculate the density of an irregularly shaped solid.
INTRODUCTION:
Density is a physical property of liquids and solids. We can define density (d) as the
amount of mass is given volume (eq 2.1). The unit of density is g/cm3 or g/mL. For a homogeneous
object, the formula mass/volume may be used. To determine the density of a liquid, the volume
may be measured directly but the mass may use an indirect technique called weighing by
difference (figure 2.1). The density of a solid material, we can measure mass directly using
balance but the volume especially an irregular object cannot to be found directly. However, its can
found indirectly from the amount of a liquid it displaces. This technique is called volume
displacement (figure 2.2).
mass
density (eq 2.1)
volume
After collecting the experiment data, we can calculate density by dividing the mass by the
volume. However, most important calculated value was the proper unit. The density of liquids and
solids is usually expressed in gram per millimeter (g/mL) or gram per cubic centimeter (g/cm 3).
Since 1 mL = 1 cm3, the numerical value for density in g/mL and g/cm3 is identical. For example,
the density of water may be expressed as 1.00 g/mL or 1.00 g/cm3.
Weighing by difference, the technique of the mass of the chemical was calculated by
subtracting the weight of an empty container from the total weight of the container and chemical.
Meanwhile, volume displacement technique based on Archimedes principle that volume of solid
(that sinks) is equal with displaces an amount of water. It is can be calculated by the difference of
volume before and volume after an object is immersed in an amount of water.
13
Figure 2.1: Weighing By Difference Figure 2.2: Volume Displacement
LAB EQUIPMENT
10 mL graduated cylinder Filter funnel
50 mL burette Dropper
100 mL beakers Wash bottle
Retort stands and clamps
EXPERIMENTAL PROCEDURE
14
Part B: Density of an Unknown Liquid
1. Rinse, clean and dry the 10.0 mL graduated cylinder (used in Part A)
2. Weigh the cylinder on an analytical balance. Record its mass to the nearest 0.01 g.
3. Obtain about 15 mL of an unknown liquid in a 100 mL beaker, and record the unknown
label.
4. By using a dropper, add between 2 to 4 mL of the unknown liquids to the cylinder. Record
the volume to the nearest 0.1 mL.
5. Weigh the liquid and cylinder on the same balance used for the first weighing, and again
records the mass to the nearest 0.01 g.
7. To validate your experimental technique, and repeat step 4 and 6 by using the same
liquid in set of volume of the unknown liquid between 5 to 7 mL and between 8 to 10 mL.
8. Calculate the density of the unknown liquid from your mass and volume (from the cylinder
and calibration graph) data.
9. Return the liquid to its container when you finish with it.
1. Rinse, clean and dry the 10.0 mL graduated cylinder (used in Part A).
2. Add about 4 to 5 mL of water to the cylinder and record the volume to the nearest 0.1 mL
3. Obtain an irregularly shaped object and record its identity label. Spread the solid onto a
towel and check to see if it is dry. Dry it with a towel, if necessary
4. Weight this object as accurately as possible and record it mass.
5. Till the graduated cylinder to about 40 angle and carefully slide the solid down into the
water (the solid should be completely submerged in water and not exceed the capacity of
the cylinder).
6. Gently tap the cylinder to remove any air bubbles adhering to the solid).
7. Record the new volume to the nearest 0.1 mL. The change in volume gives the volume of
the solid.
8. To validate your experimental technique, and repeat all step by using the same object
(must clean and dry) in set of volume between 5 to 6 mL and between 6 to 7 mL of the
water to the cylinder.
9. Calculate the density of the unknown liquid from your mass and volume (from the cylinder
and calibration graph) data.
15
UNIVERSITI TEKNIKAL No. Dokumen: No. Isu./Tarikh
MALAYSIA MELAKA TB/MMK/ DACS 1232 1/7-7-2010
CHEMISTRY
No. Semakan/Tarikh Jumlah Mukasurat
Experiment 3: Preparation and Standardization
1/7-7-2010 3
of Solution
OBJECTIVE:
To prepared and determine the concentration of solution
LEARNING OUTCOMES
After conducting this experiment, you should be able to:
1. How to prepare the standard solution and dilute the solution
2. Determine the concentration of solution in various units
INTRODUCTION:
In chemistry, concentration is the measure of how much of a given substance there is mixed with
another substance. This can apply to any sort of chemical mixture, but most frequently the concept
is limited to homogeneous solutions, where it refers to the amount of solute in a substance
A standard solution is prepared from pure ( 99%) substance and the exact concentration of
the solution is known. Some solutions need to be standardized because their concentrations vary
over time due to chemical reactions such as oxidation.
To lower the concentration of solution, we use the process of dilution, or adding more solvent
to a solution. In this process, the relative numbers of solute and solvent particles change. Adding
more solvent increase the number of solvent particles and increases the volume. For a given amount
of the original solution, the number of solute stays the same, but they are spread out through a
greater volume, so their concentration is less.
If we dilute a solution of known molarity, we can calculate the molarity of diluted solution using
the formula given by.
M 1V 1 M 2V 2 (eq. 3.1)
where M1 and V1 the molarity and volume of the solution before dilution, M2 and V2 are the
molarity volume of the solution after dilution
16
solution of unknown concentration into a conical flask, followed by the addition of an indicator
solution.
An indicator solution is a dye that has one color in an acidic solution and another in a basic
solution. A standard solution is that added from the burette until some visual effect, such as color
change, signals that the reaction is complete. The solution in the burette is referred to as the titrant.
In this experiment, you will be required to prepare a standard solution of oxalic acid. The
oxalic acid will be used to standardize a solution of sodium hydroxide of unknown concentration.
The chemical reaction between oxalic acid and sodium hydroxide occurs as follows:
H 2 C 2 O 4 2 H 2 O 2 NaOH Na 2 C 2 O 4 2 H 2 O (eq. 3.2)
The molar equivalence of the reactants can be calculated using the formula given by
M aV a M bV b
(eq. 3.3)
a b
Where Ma and Va the molarity and volume of the acid, Mb and Vb are the molarity and the volume
of the base; a and b are the stoichiometric constants respectively.
LAB EQUIPMENT
Small and large beakers 20 mL pipette
100 mL volumetric flask Filter funnel
50 mL burette Dropper
Retort stands and clamps Glass rod
250 mL conical flask
EXPERIMENTAL PROCEDURE
17
Part C: Titration
1. Set up the equipment for titration. Use a beaker to obtain approximately 80 mL of NaOH
solution (that have prepared from Part B)
2. Fill the burette with the oxalic acid that you have prepared from Part A (use a funnel).
Record the initial reading on the burette.
3. Pipet 20 mL of NaOH into a conical flask and add 2 - 5 drops of Thymol Blue. Titrate the
NaOH solution until the color of the solution changes from blue to a permanent light
yellow. Record the final reading.
4. Repeat step 2 and 3 two more times. Determine the average amount of oxalic acid used.
5. Calculate the concentration of diluted NaOH and standard NaOH (already prepared for
you in lab)
18
UNIVERSITI TEKNIKAL No. Dokumen: No. Isu./Tarikh
MALAYSIA MELAKA TB/MMK/ DACS 1232 1/7-7-2010
OBJECTIVE:
To determine the percent by mass of acetic acid in vinegar.
LEARNING OUTCOMES
After conducting this experiment, you should be able to:
1. Calculate the concentration of acetic acid in vinegar
2. Determine the percent by mass of acetic acid in vinegar
INTRODUCTION:
Acetic acid is the chemical compound responsible for the characteristic odor and sour taste
of vinegar. Household vinegar is a 4 – 5 % (by mass) acetic acid, CH3COOH, solution (4% is the
minimum federal standard). Generally, caramel flavoring and coloring are also added to make
the product aesthetically more appealing. In this experiment you are going to analyze a sample of
vinegar to find the percent-by-mass of acetic acid in the vinegar.
The titration techniques is the method used for determine of the percent by mass of acetic
acid in vinegar. A measured mass of vinegar is titrated to the phenolphthalein or thymol blue
endpoint with a measured volume of a standardized sodium hydroxide solution. As the volume and
molar concentration of the standardized NaOH solution are known, the moles of NaOH used for
the analysis are also known.
The mass of CH3COOH in the vinegar is calculated from the measured moles of CH 3COOH
neutralized in the reaction and its molar mass, 60.05 g/mol:
mass ( g ) of CH 3 COOH
% by mass of CH 3 COOH 100 % (eq. 4.3)
mass ( g ) of vinegar
19
LAB EQUIPMENT
Volumetric flask 100 mL, Burette 50 mL,
Pipette 20 mL, Conical flask 125 or 250 mL
EXPERIMENTAL PROCEDURE:
1. Clean 100 mL volumetric flask, and measure its mass.
2. Add the 10 mL of the vinegar to a volumetric flask with previously measured mass.
3. Measure the combined mass of the volumetric flask and sample of vinegar.
4. Dilute a concentrated solution with fill the volumetric flask to the 100 mL mark using
distilled water, gently shake the solution.
5. In 125 or 250 mL Erlenmeyer flask, pipette 20 mL of the diluted acid solution (from
volumetric flask). Add 5 drop of thymol blue indicator solution.
6. Rinse a clean 50 mL burette with the standardized NaOH solution; fill the burette with
NaOH solution. Adjust the volume to the zero mark and record the initial volume.
7. Titrate the sample solution with NaOH solution until the solution just turns blue and the blue
color persists for 30 seconds. Read and record the final volume of NaOH titrant in the
burette.
8. Repeat the titration procedure above (step 5 to 7), 2 more times.
20
UNIVERSITI TEKNIKAL No. Dokumen: No. Isu./Tarikh
MALAYSIA MELAKA TB/MMK/ DACS 1232 1/7-7-2010
OBJECTIVE:
The primary objective of this experiment is to determine the relationship between the pressure and
volume of a confined gas.
INTRODUCTION:
The gas we use will be air, and it will be confined in a syringe connected to a Pressure Sensor (see
Figure 5.1). When the volume of the syringe is changed by moving the piston, a change occurs in
the pressure exerted by the confined gas. This pressure change will be monitored using a Pressure
Sensor. It is assumed that temperature will be constant throughout the experiment. Pressure and
volume data pairs will be collected during this experiment and then analyzed. From the data and
graph, you should be able to determine what kind of mathematical relationship exists between the
pressure and volume of the confined gas. Historically, this relationship was first established by
Robert Boyle in 1662 and has since been known as Boyle’s law.
LAB EQUIPMENT
Windows PC Vernier computer interface Vernier Gas Pressure Sensor
Logger Pro 20-mL gas syringe
EXPERIMENTAL PROCEDURE:
1. Prepare the Pressure Sensor and an air sample for data collection.
a. Plug the Pressure Sensor into Channel 1 of the computer interface. With the 20-mL
syringe disconnected from the Pressure Sensor, move the piston of the syringe until the
front edge of the inside black ring (indicated by the arrow in Figure 5.1) is positioned at
the 10.0 mL mark.
b. Attach the 20-mL syringe to the valve of the Pressure. Newer Vernier Gas Pressure
Sensors have a white stem protruding from the end of the sensor box—attach the
syringe directly to the white stem with a gentle half-turn.
21
2. Prepare the computer for data collection.
a. Prepare the computer for data collection by opening the Experiment 6 folder from
Chemistry with Computers. Then open the experiment file that matches the sensor you are
using.
b. On the Graph window, the vertical axis has pressure scaled from 0 to 250 kPa. The
horizontal axis has volume scaled from 0 to 20 mL.
3. Click Collect to begin data collection.
4. Collect the pressure vs. volume data. It is best for one person to take care of the gas syringe
and for another to operate the computer.
a. Move the piston to position the front edge of the inside black ring (see Figure 5.2) at the
5.0-mL line on the syringe. Hold the piston firmly in this position until the pressure value
stabilizes.
b. When the pressure reading has stabilized, click Keep. Type “5.0” in the edit box. Press
the ENTER key to keep this data pair. Note: You can choose to redo a point by pressing
the ESC key (after clicking Keep , but before entering a value).Continue the procedure
for volumes of 7.5, 10.0, 12.5, 15.0, 17.5, and 20.0 mL.
c. Click Stop when you have finished collecting data.
5. In your data table, record the pressure and volume data pairs displayed in the Table
window (or, if directed by your instructor, print a copy of the Table window).
6. Examine the graph of pressure vs. volume. Based on this graph, decide what kind of
mathematical relationship you think exists between these two variables, direct or inverse. To
see if you made the right choice:
a. Click the Curve Fit button, .
b. Choose Variable Power (y = Ax^n) from the list at the lower left. Enter the value of n in
the Degree/Exponent edit box that represents the relationship shown in the graph
(e.g.,type “1” if direct, “-1” if inverse). Click Try Fit.
c. A best-fit curve will be displayed on the graph. If you made the correct choice, the curve
should match up well with the points. If the curve does not match up well, try a different
exponent and click Try Fit again. When the curve has a good fit with the data points,
then click OK .
7. Once you have confirmed that the graph represents either a direct or inverse relationship,
print a copy of the Graph window, with the graph of pressure vs. volume and its best-fit
curve displayed. Enter your name(s) and the number of copies you want to print.
22
UNIVERSITI TEKNIKAL No. Dokumen: No. Isu./Tarikh
MALAYSIA MELAKA TB/MMK/ DACS 1232 1/7-7-2010
OBJECTIVE:
To calculate the heat of reaction of carbonates compound
INTRODUCTION:
Chemical reactions are always accompanied by energy changes. A chemical reaction that
releases heat energy to the environment is said to be exothermic. One that absorbs heat from the
environment is said to be endothermic. The heat change of a system at constant pressure is called
the heat of reaction or enthalpy change. The enthalpy change of a system is given by symbol H.
The heat content of a system which undergoes an exothermic reaction is negative because the heat
content is reduced.
Calorimetry is the basic technique for studying any process where heat energy is of
interest. Calorimeters are designed to be well-insulated, so no heat is gained from or lost to the
surroundings. The basic strategy in calorimetry is to use a temperature change and a heat capacity
to determine the heat of reaction using the following equation:
q so ln m s T C p T (eq. 6.1)
The heat capacity of the calorimeter, Cp is often ignored such that equation 6.1 may be
simplified as follows:
q so ln m s T (eq. 6.2)
The molar enthalpy of a reaction, Hsoln is negative of the heat of reaction, qsoln per mole
of limiting reagent, n
q so ln
H so ln (eq. 6.3)
n
The objective of this experiment is to determine the heat of reaction (qrxn) and calculate the molar
enthalpy H of following reactions:
The calculations are simplified by assuming the value of s as equal to 4.18 J/ g C and the density
of the final solution as equal to 1.0 g/mL. The heat capacity of the calorimeter can be ignored.
23
LAB EQUIPMENT
Thermometer Glass stirrer
20 mL pipette Small towel
50 mL beaker Large filter paper or cardboard (calorimeter
100 mL beaker covering)
200 mL beaker
EXPERIMENTAL PROCEDURE:
1. Construct a simple calorimeter (see figure 6.1) using the 100 mL and 200 mL beakers and
a small towel. Be sure to dry the inner beaker thoroughly before use.
2. Using the inner beaker, weigh 1.80 – 2.20 g of Na2CO3. Record the exact weight of the
solid. Place the inner beaker inside the larger beaker as shown in the figure.
3. Pipet 20 mL of the HCl solution into another beaker and measure initial temperature, Tinitial
(to one decimal place)
4. Pour the acid into the calorimeter and immediately replace the calorimeter covering. Stir
the solution and determine the highest temperature (if temperature rises) or lowest
temperature (if the temperature decreases). Record this temperature as the final
temperature of the reaction, Tfinal.
5. Thoroughly clean the inner beaker (of the calorimeter) and repeat step 2 – 4, this time
weight 2.5 – 3.0 g of NaHCO3.
6. Calculate T, qsoln and H1 and H2
Thermometer
Stirrer
Calorimeter
Covering
200 mL beaker
100 mL beaker
Insulator
(Towel) Solution
24
LAB REPORT
EXPERIMENT 1
Usage and Calibrate of Lab Glassware Equipment
25
B. QUESTIONS
b. burette
c. measuring cylinder
3. Why is that the last drop of water or solution should no be blown out during the transfer
using a pipette?
26
LAB REPORT
EXPERIMENT 2
Density of Liquid and Solid
Measuring of volume:
Volume of liquid in graduated
cylinder(mL) ……………… ……………… ………………
Volume of liquid from
calibration graph (mL) ……………… ……………… ………………
Calculating of density:
Density of liquid ……………… ……………… ………………
27
Part C: Density of an Irregularly Shaped Solid
Measuring of volume:
Volume of water in graduated
cylinder(mL) ……………… ……………… ………………
Total volume :water+ solid
object (mL) ……………… ……………… ………………
Calculating of density:
Density of solid object ……………… ……………… ………………
B. QUESTIONS
1. Calculate the density of a rectangular solid which has a mass 25.71 g. It is 2.30 cm long,
4.01 cm wide and 1.82 cm high.
28
2. The density of pure gold is 19.3 g/mL. A ‘gold’ bracelet has a mass of 48.2 g and
displaces 3.00 mL of water. Is the bracelet pure gold?
3. The mass of the Earth is 5.98 x 1024 kg and average diameter is 12700 km. assuming the
earth is spherical, what is the average density of our planet in g/cm3
29
30
LAB REPORT
EXPERIMENT 3
Preparation and Standardization of Solution
31
Part B: Dilution of NaOH solution
Dilution of NaOH solution result:
Initial volume of NaOH solution (mL) : ………………………………
Final volume of NaOH solution (mL) : ………………………………
Part C: Titration
B. QUESTIONS
1. Calculate the molarity of diluted NaOH and standard NaOH (already prepared for you
in lab)
32
LAB REPORT
EXPERIMENT 4
Vinegar Analysis
B. QUESTIONS
1. Calculate molar concentration of acid acetic in the vinegar sample after titration
33
2. Calculate the percent by mass (% w/w) of acid acetic in this vinegar?
3. Compare with minimum federal standard, calculate the percent of differences of vinegar?
Give comment.
34
LAB REPORT
EXPERIMENT 5
Boyle’s Law: Pressure-Volume Relationship in Gases
B. QUESTIONS
1. If the volume is doubled from 5.0 mL to 10.0 mL, what does your data show happens to the
pressure? Show the pressure values in your answer.
2. If the volume is halved from 20.0 mL to 10.0 mL, what does your data show happens to the
pressure? Show the pressure values in your answer.
35
3. If the volume is tripled from 5.0 mL to 15.0 mL, what does your data show happened to the
pressure? Show the pressure values in your answer.
4. From your answers to the first three questions and the shape of the curve in the plot of pressure
versus volume, do you think the relationship between the pressure and volume of a confined
gas is direct or inverse? Explain your answer.
5. Based on your data, what would you expect the pressure to be if the volume of the syringe
was increased to 40.0 mL? Explain or show work to support your answer.
6. Based on your data, what would you expect the pressure to be if the volume of the syringe
was decreased to 2.5 mL? Explain or show work to support your answer.
36
7. What experimental factors are assumed to be constant in this experiment?
9. How constant were the values for k you obtained in Question 8? Good data may show some
minor variation, but the values for k should be relatively constant.
10. Using P, V, and k, writes an equation representing Boyle’s law. Write a verbal statement that
correctly expresses Boyle’s law.
37
LAB REPORT
EXPERIMENT 6
Heat of Reaction of Carbonates
Part A:
Weighing Result:
Mass of beaker (g) ……………..………….
Part B:
Weighing Result:
Mass of beaker (g) ……………..………….
T(C) ……………..…………..
B. QUESTIONS
1. Calculate the heat of reaction
38
2. Calculate the enthalpy reaction
4. Student performs a calibration experiment to determine the heat capacity of the calorimeter.
The student mixes 25.0 mL of warm water at 41.2 °C and 35.0 mL of cool water at 15.1°C.
The final temperature of the mixture is 19.8°C. Assume that the specific heat of water is 4.184
J/g °C and that the density of water is 1.00 g/mL. Calculate the heat capacity of the
calorimeter.
39