Scribd Logo
Upload

Welcome to Scribd!

  • DFS TEST SOP For FCC ID Q78-ZXHNF680

    Uploaded by

    Willem Vos
    49 views13 pages
    1. The document provides steps to test a FCC DFS device, including setting up the equipment under test (EUT) and connecting it to a notebook, installing a wireless USB adapter driver, and proceeding with DFS tests. 2. It describes commands to configure the EUT's transmitting bandwidth and channel in both normal and engineering modes. In engineering mode, the EUT will not avoid radar signals or immediately jump back to the used channel when a signal is found. 3. The steps also include running traffic on the EUT, accessing the EUT's website to check settings, and notes on troubleshooting during testing and restarting the EUT if needed.

    Original Description:

    Original Title

    DFS TEST SOP for FCC ID Q78-ZXHNF680

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Report this Document
    1. The document provides steps to test a FCC DFS device, including setting up the equipment under test (EUT) and connecting it to a notebook, installing a wireless USB adapter driver, and proceeding with DFS tests. 2. It describes commands to configure the EUT's transmitting bandwidth and channel in both normal and engineering modes. In engineering mode, the EUT will not avoid radar signals or immediately jump back to the used channel when a signal is found. 3. The steps also include running traffic on the EUT, accessing the EUT's website to check settings, and notes on troubleshooting during testing and restarting the EUT if needed.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Flag for inappropriate content
    Download as pdf or txt
    49 views13 pages

    DFS TEST SOP For FCC ID Q78-ZXHNF680

    Uploaded by

    Willem Vos
    1. The document provides steps to test a FCC DFS device, including setting up the equipment under test (EUT) and connecting it to a notebook, installing a wireless USB adapter driver, and proceeding with DFS tests. 2. It describes commands to configure the EUT's transmitting bandwidth and channel in both normal and engineering modes. In engineering mode, the EUT will not avoid radar signals or immediately jump back to the used channel when a signal is found. 3. The steps also include running traffic on the EUT, accessing the EUT's website to check settings, and notes on troubleshooting during testing and restarting the EUT if needed.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Flag for inappropriate content
    Download as pdf or txt
    of 13

    FCC 

    DFS Test SOP
    FCC ID: Q78‐ZXHNF680 

    Step 1: Setup EUT as below photos. 
    Connect EUT to a notebook via a LAN cable. 
    Step 2: Install wireless USB adapter driver 
    a. Plug the wireless USB adapter to another PC, and place the driver. Below 
    dialog box will appear, then click “run CDView.exe”. 
     

     
    b. Below dialog box will appear, and then click ”Install”. 
     

     
     

     
    c. Below dialog box will appear, and then select ” next step”. 

     
    d. Below dialog box will appear, showing the driver is under installing. 
     

     
     

     
    e. Below dialog box will appear to indicate that the driver is installed 
    successfully, and then restart the PC. 
    f.  

     
     

     
    Step 3: Proceed DFS test 
    a. Make the notebook automatically obtain IP address 
    b. Open the CMD command prompt window 
    c. Use telnet command to connect PC 
                  telnet 192.168.1.1 
    Username: tellmeyourname 
                      Password: H3‐manp0w3r! 
     

    Step 4: Input control command to EUT, then set up and check the transmitting 
    bandwidth of EUT, please follow below commands to proceed configuration 
     
    a. Set up 20M bandwidth 
    iwpriv wlan4 mode 11ACVHT20 
     
    b. Set up 40M bandwidth 
    iwpriv wlan4 mode 11ACVHT40 
     
    c. Set up 80M bandwidth 
    iwpriv wlan4 mode 11ACVHT80 
     
    d. Check the command of used mode 
    iwpriv wlan4 get_mode 
     

     
     

     
    Step 5: Set up and check the transmitting channel of EUT 
    a. Command of control used channel 
    iwconfig wlan4 channel 100 
     
    b. Command of check used channel 
    iwlist wlan4 channel   
     

     
     

     
    Step 6: When test for statistical performance of EUT avoid radar signal, you can use 
    command to make EUT enter into engineering mode, which will make EUT 
    not avoid or immediately jump back to used channel when find radar signal, 
    and feedback the information of finding radar signal and jump back to used 
    channel. 

     
    a. Command of entering into engineering mode 
    radartool ‐i wifi1 usenol 0        ‐‐‐ 0 is engineering mode, 1 is normal mode 

     
     

     
    b. Feedback information setting 
    sendcmd log klogtelnet info   
    sendcmd log Klogtelnet enable 1   
    sendcmd log klogtelnet ttyp0 enable 1   

           

     
         

               
    Input regulation intensity radar jamming signal on EUT used channel, EUT will find 
    this radar signal and feedback information 

     
     
    If EUT cannot find the radar signal or has low success rate (statistical performance) of 
    avoiding radar signal, then you can modify EUT’s sensitivity. 
    The three commands as following need to be proceeded after finishing setting mode, 
    channel and engineering mode.   

    Command of sensitivity setting: 
    athdiag -D /sys/devices/pci0000:00/0000:00:01.0 --get --address=0x29834
    athdiag -D /sys/devices/pci0000:00/0000:00:01.0 --set --address=0x29834 --value=0x64408200
     

    Step 7: Examples of commands integrated 
    a. Setting normal mode AC20 5540MHz:

    iwpriv wlan4 mode 11ACVHT20 
    iwpriv wlan4 get_mode 
    iwconfig wlan4 channel 108    // modify channel 
    iwlist wlan4 channel 
    radartool ‐i wifi1 usenol 1 

    b. Setting normal mode AC40 5550MHz

    iwpriv wlan4 mode 11ACVHT40 
    iwpriv wlan4 get_mode 
    iwconfig wlan4 channel 108    // modify channel 
    iwlist wlan4 channel 
    radartool ‐i wifi1 usenol 1 

    c. Setting normal mode AC80 5530MHz

    iwpriv wlan4 mode 11ACVHT80 
    iwpriv wlan4 get_mode 
    iwconfig wlan4 channel 100    // modify channel 
    iwlist wlan4 channel 
    radartool ‐i wifi1 usenol 1 

    Note: After testing Channel Move Time and Channel Availability Check, if normal 
    mode command can’t change mode or channel successfully, please restart EUT. 
    d. Setting engineering mode AC20 5540MHz 
    iwpriv wlan4 mode 11ACVHT20 
    iwconfig wlan4 channel 108      // modify channel 
    radartool ‐i wifi1 usenol 0 
    sendcmd log klogtelnet info   
    sendcmd log Klogtelnet enable 1   
    sendcmd log klogtelnet ttyp0 enable 1 
     
    e. Setting engineering mode AC40 5550MHz 
    iwpriv wlan4 mode 11ACVHT40 
    iwconfig wlan4 channel 108    // modify channel 
    radartool ‐i wifi1 usenol 0 
    sendcmd log klogtelnet info   
    sendcmd log Klogtelnet enable 1   
    sendcmd log klogtelnet ttyp0 enable 1 
     
    f. Setting engineering mode AC80 5530MHz 
    iwpriv wlan4 mode 11ACVHT80 
    iwconfig wlan4 channel 100      // modify channel 
    radartool ‐i wifi1 usenol 0 
    sendcmd log klogtelnet info   
    sendcmd log Klogtelnet enable 1   
    sendcmd log klogtelnet ttyp0 enable 1 

       

     
    Note: Every time change mode channel under engineering mode, please on 
    standby for a few minutes before testing. Normal mode and engineer mode cannot 
    interconvert, which need restart the EUT and then reset the mode.   

     
    Step 8: Open Run flow software  
    Packet size: 1250   
    Packet rate: modify this parameter to adjust the flow intensity 
    Local IP: obtain local IP address automatically 
    Destination IP: wireless access IP address   
    Kindly  note:  The  computer  to  control  DFS  test  cannot  be  the  same  one  which 
    wireless USB adapter connected to   
     

     
     

    Step  9:  Access  website  (obtain  local  IP  automatically),  input  gateway: 
    192.168.1.1 (must use Google browser) 
     
                    Username: Admin   
                      Password: Spr1tZ007! 
     
     

                  Step 10: Check the 5G WIFI settings as below shown. 

     
     

     
    Kindly note: please restart EUT if there is any problem that can’t be solved during 
    testing. 

    You might also like