Professional Documents
Culture Documents
Microwave Oven: Service Manual
Microwave Oven: Service Manual
com
MICROWAVE OVEN
SERVICE MANUAL
MODEL: LTRM1240SW
LTRM1240SB
LTRM1240ST
CAUTION
BEFORE SERVICING THE UNIT, READ THE
SAFETY PRECAUTIONS IN THIS MANUAL.
July, 2004
P/NO : 3828W5S6018 Printed in Korea
SAFETY PRECAUTIONS
This device is to be serviced only by properly qualified service personnel.
Consult the service manual for proper service procedures to assure continued safety operation and for precautions to be taken to
avoid possible exposure to excessive microwave energy.
CAUTION
MICROWAVE RADIATION
DO NOT BECOME EXPOSED TO RADIATION FROM THE MICROWAVE GENERATOR
OR OTHER PARTS CONDUCTING MICROWAVE ENERGY.
-1-
FOREWORD
Read this Manual carefully. Failure to adhere to or observe the information in this Manual may result in exposing yourself to
the Microwave Energy normally contained within the oven cavity.
TABLE OF CONTENTS
2. Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3. Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4. Installations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
-2-
SPECIFICATIONS
ITEM DESCRIPTION
MODEL LTRM1240SW
LTRM1240SB
LTRM1240ST
Power Requirement 120 Volts AC 60 Hz
Single phase, 3 wire grounded
Microwave 1650W
Toast 800W
Nameplate Location
Back Side
Accessories
Owner's manual
Glass turntable
Roller rest
-3-
CAUTIONS
Unlike other appliances, the microwave oven is
high-voltage and high-current equipment.
MICROWAVE RADIATION
Though it is free from danger in ordinary use, Personnel should not be exposed to the microwave
extreme care should be taken during repair. energy which may radiate from the magnetron or
other microwave generating device if it is improperly
used or connection.
• DO NOT operate on a 2-wire extension cord during repair All input and output microwave connections,
and use. waveguide, flange and gasket must be secure
• NEVER TOUCH any oven components or wiring during never operate the device without a microwave
operation. energy absorbing load attached.
• BEFORE TOUCHING any parts of the oven, always remove Never look into an open waveguide or antenna
the power plug from the outlet. while the device is energized.
• For about 30 seconds after the oven stops, an electric
charge remains in the high voltage capacitor. When
replacing or checking, you must discharge the high voltage • Proper operation of the microwave oven requires that the
capacitor by shorting across the two terminals with an magnetron be assembled to the waveguide and cavity.
insulated screwdriver. Never operate the magnetron unless it is properly installed.
• Be sure that the magnetron gasket is properly installed
around the dome of the tube whenever installing the
magnetron.
ANTENNA
Gasket
COOLING FIN
FILAMENT
TERMINALS
MAGNETRON
CHASSIS GROUND
• Remove your watches whenever working close to or MAGNETRON
replacing the Magnetron.
• DO NOT touch any parts of the control panel circuit. A
resulting static electric discharge may damage this P.C.B.
• NEVER operate the oven with no load.
• NEVER injure the door seal and front plate of the oven THE OVEN IS TO BE SERVICED ONLY BY
cavity. PROPERLY QUALIFIED SERVICE
• NEVER put iron tools on the magnetron. PERSONNEL.
• NEVER put anything into the latch hole and the interlock
switches area.
-4-
INSTALLATIONS
BEFORE YOU BEGIN, READ THE FOLLOWING INSTRUCTIONS COMPLETELY AND CAREFULLY.
4. The oven should not be installed in any area where heat PREFERRED METHOD
and steam are generated, because they may damage
the electronic or mechanical parts of the unit.
Do not install the oven next to a conventional surface
unit or above a conventional wall oven.
ENSURE PROPER GROUND
5. Use microwave oven in an ambient temperature less EXISTS BEFORE USE
than 104°F(40°C).
6. Place the microwave oven on a sturdy and flat surface TEMPORARY METHOD
at least 10 cm(4 inches) from the wall. (ADAPTER PLUGS NOT
PERMITTED IN CANADA)
7. Place the microwave oven as far away as possible from ALIGN LARGE
TV, RADIO, COMPUTER, etc., to prevent interference. PRONGS/SLOTS
10cm
-5-
A. SCHEMATIC DIAGRAM
6. OVERALL CIRCUIT DIAGRAM
-6-
IMPORTANT SAFETY NOTE: THE SHADED AREAS ON THIS SCHEMATIC DIAGRAM INCORPORATE SPECIAL FEATURES
IMPORTANT FOR PROTECTION FROM MICROWAVE RADIATION, FIRE, ELECTRICAL SHOCK, AND
HAZARDS. WHEN SERVICING IT IS ESSENTIAL THAT ONLY MANUFACTURER’S SPECIFIED PARTS
BE USED FOR THE CRITICAL COMPONENTS IN THE SHADED AREAS OF THE SCHEMATIC DIAGRAM.
NOTICE: SINCE THIS IS BASIC SCHEMATIC DIAGRAM, THE VALUES OF COMPONENTS AND
SOME PARTIAL CONNECTIONS ARE SUBJECT TO CHANGE FOR IMPROVEMENT.
B. MATRIX CIRCUIT FOR TOUCH KEY BOARD
-7-
7. OPERATING PROCEDURES
A. OVEN CONTROL PANEL
13 5 7 9 11 1 12 3
1. DISPLAY. The Display includes a clock and indicators that tell you time of day, cooking time settings, and cooking
functions selected.
2. STOP/CLEAR. Touch this pad to stop the oven or clear entries.
3. START. Touch this pad to start all entries (except the Auto Cook and Add Minute function which start automatically)
and to turn Child Lock on or off.
4. AUTO COOK. Touch this pad to select programming food items.
5. EZ-ON. Touch this pad to cook at 100% cook power for 1 minute to 99 minutes 59 seconds.
6. AUTO DEFROST. This pad is an accurate defrosting method for frozen meat, poultry and fish up to 6.0 lbs.
7. Q-DEFROST. This pad provides you with the quick defrosting method for 1.0 pound frozen foods.
8. CUSTOM SET. Touch this pad to change the oven's default settings for sound, clock, scroll speed and Lbs/Kg.
9. KITCHEN TIMER. Touch this pad to use your microwave oven as a kitchen timer.
10. COOK TIME. Touch this pad to set a cooking time.
11. POWER. Touch this pad to set a cooking power.
12. NUMBER PADS. Touch Number Pads to enter cooking time, power level, quantities, or weights.
13. SENSORTOUCH. This pad allows you to cook most of your favorite foods without having to select cooking times and
power levels.
-8-
B. EASY USE TABLE TOASTER
MICROWAVE OVEN (1) TOAST
(1) KITCHEN TIMER 1. Touch STOP/CLEAR.
1. Touch STOP/CLEAR. 2. Touch TOAST.
2. Touch KITCHEN TIMER. 3. Touch Darkness Control (1~9 step)
3. Touch correct number for time. 4. Touch START.
4. Touch START.
(2) BAGEL
(2) CHILD LOCK
1. Touch STOP/CLEAR.
To set:
2. Touch BAGEL.
1. Touch STOP/CLEAR.
3. Touch Darkness Control (1~9 step)
2. Touch “START” more than 4 seconds.
4. Touch START.
To cancel:
1. Touch STOP/CLEAR.
(3) DARKNESS SETTINGS
2. Touch “START” more than 4 seconds.
(3) AUTO COOK Degree of darkness Select darkness level
1. Touch STOP/CLEAR.
Light 1~3
2. Touch AUTO COOK Category.
3. Touch START. Medium 4~6
(Although you don’t touch start, it will start after Dark 7~9
4 seconds automatically)
(4) EZ-ON
1. Touch STOP/CLEAR.
2. Touch EZ-ON
(5) AUTO DEFROST
1. Touch STOP/CLEAR.
2. Touch AUTO DEFROST.
Three different defrosting levels are provided.
(Touch 1 : Meat
Touch 2 : Poultry
Touch 3 : Fish)
3. Enter the weight of your food in decimal
increments from 0.1 to 6.0 pounds.
4. Touch START
5. At beeping, turn food over by following the
instructions in the manual.
6. After turning food over, touch START to resume
defrosting.
(6) TIMED COOKING
1. Touch STOP/CLEAR.
2. Touch COOK TIME.
3. Touch number for cooking time.
4. Touch POWER.
5. Touch number for cooking power level.
6. Touch START.
(7) MULTI-STAGE COOKING
1. Touch STOP/CLEAR.
2. Touch COOK TIME.
3. Touch number for cooking time.
4. Touch POWER.
5. Touch number for cooking power level.
6. Repeat steps 2-5 to set 2nd cooking stage.
7. Touch START.
-9-
8. PROCEDURE FOR MEASURING MICROWAVE
ENERGY LEAKAGE
A. CAUTIONS B. MEASURING MICROWAVE ENERGY LEAKAGE
(1) Be sure to check a microwave emission prior to servicing (1) Pour 275±15cc of 20±5 °C water in a beaker which is
the oven if the oven is operative prior to servicing. graduated to 600 cc, and place the beaker in the center
(2) The service personnel should inform the manufacturer, of the oven.
importer, or assembler of any certified oven unit found to (2) Set the energy leakage monitor to 2450 MHz and use it
have a microwave emission level in excess of following the manufacturer’s recommended test
5mW/cm.sq. and should repair any unit found to have procedure to assure correct result.
excessive emission levels at no cost to the owner and (3) When measuring the leakage, always use the 2 inch
should ascertain the cause of the excessive leakage. (5cm) spacer supplied with the probe.
The service personnel should instruct the owner not to (4) Operate the oven at its maximum output.
use the unit until the oven has been brought into (5) Measure the microwave radiation using and
compliance. electromagnetic radiation monitor by holding the probe
(3) If the oven operates with the door open, the service perpendicular to the surface being measured. (See
personnel should; Figure 6)
- Tell the user not to operate the oven
- Contact the manufacturer and CDRH (Center for Move probe along shaded area.
Devices and Radiological Health) immediately.
NOTE: Address on CDRH
Probe scanning speed
Office of Compliance (HFZ-312)
less than 2.5 cm/sec.
Center for Devices and Radiological Health
1390 Piccard Drive
Rockville, Maryland 20850
(4) The service personnel should check all surface and vent
openings for microwave emission testing.
(5) Check for microwave energy leakage after every
servicing. The power density of the microwave radiation
leakage emitted by the microwave oven should not
exceed 1mW/cm.sq. And always start measuring of an
unknown field to assure safety for operating personnel
from radiation leakage.
NOTE: The standard is 5mW/cm.sq. while in the
customer’s home. 1mW/cm.sq. stated here is
manufacturer’s own voluntary standard for units in
customer’s home.
C. MEASUREMENT WITH THE OUTER CASE REMOVED
(1) When you replace the magnetron, measure for
EQUIPMENT
microwave energy leakage before the outer case is
• Electromagnetic energy leakage monitor (NARDA 8100B,
installed and after all necessary components are
HOLADAY HI 1501)
replaced or adjusted. Special care should be taken in
• 600cc glass beaker
measuring the following parts.
• Glass thermometer 1000C
- Around the magnetron
- The waveguide
-10-
D. MEASUREMENT WITH A FULLY ASSEMBLED OVEN G. POWER OUTPUT MEASUREMENT
(1) After all components, including the outer panels, are (1) Fill the test beaker with 59 °F(15 °C) ~ 75 °F(24 °C) 1 liter tap
fully assembled, measure for microwave energy water.
leakage around the door viewing window, the exhaust (2) Stir the water in the beaker with thermometer (°F or °C) and
opening and air inlet openings. measure temperature as T1.
(2) Microwave energy leakage must not exceed the values (3) Place the beaker on the center of turntable.
prescribed below. (4) Set for one (1) minute and three (3) seconds and operate
NOTES: the oven at high power.
Leakage with the outer panels removed - less than NOTE: The additional three (3) seconds is to allow the
5mW/cm.sq. Leakage for a fully assembled oven magnetron to begin generating power.
(Before the latch switch (primary) is interrupted) with the (5) When the heating is finished, stir the water again with
door in a slightly opened position - less than thermometer and measure the temperature of water as T2.
1 mW/cm .sq. (6) Subtract T1 from T2, this will give you the temperature rise.
(7) The microwave power output is within specification, if the
E. NOTE WHEN MEASURING temperature rise is as shown below:
(1) Do not exceed meter full scale deflection.
(2) The test probe must be removed no faster than 1 Temperature Rise
inch/sec (2.5cm/sec) along the shaded area, otherwise Line Voltage Degrees °F Degrees °C
a false reading may result.
120 V 17.1 ~ 22.5 9.5 ~ 12.5
(3) The test probe must be held with the grip portion of the
handle. A false reading may result if the operator’s 108 V Min. 12.6 Min. 7.0
hand is between the handle and the probe.
(4) When testing near a corner of the door, keep the probe (8) Power output will be influenced by line voltage of power
perpendicular to the surface making sure the probe supply. Consequently, correct power output must be
horizontally along the oven surface, this may possibly measured within 120V AC ± 1 Volt while unit is operating.
cause probe damage.
-11-
9. DISASSEMBLY INSTRUCTIONS
IMPORTANT NOTES:
UNIT MUST BE DISCONNECTED FROM ELECTRICAL
OUTLET WHEN MAKING REPAIRS, RE-PLACEMENTS, Remove screw
ADJUSTMENTS AND CONTINUITY CHECKS. WAIT AT
LEAST ONE MINUTE, UNTIL THE HIGH VOLTAGE
securing
CAPACITOR IN THE HIGH VOLTAGE POWER screw
SUPPLY HAS FULLY DISCHARGED. THE CAPACITOR
SHOULD BE DISCHARGED BY USING INSULATED
WIRE - I.E. TEST PROBE CONNECTED TO 10KOHM
RESISTOR IN SERIES TO GROUND. WHEN
RECONNECTING THE WIRE LEADS TO ANY PART,
MAKE SURE THE WIRING CONNECTIONS AND LEAD
COLORS ARE CORRECTLY MATCHED ACCORDING
TO THE OVERALL CIRCUIT DIAGRAM. (ESPECIALLY
SWITCHES ANDHIGH VOLTAGE CIRCUIT.)
-12-
C. DOOR GROSS ASSEMBLY REMOVAL
(1) Open the door.
(2) Remove the choke cover cap very carefully with a flat-blade
screwdriver.
CAUTION : Be careful not to damage door seal plate by
screwdriver.
(3) Lift up and push the door.
NOTE:
1. After replacing the door, be sure to check that the primary
switch, monitor switch, and secondary switch operate
normally.
2. After replacing the door, check for microwave energy leakage
with a survey meter. Microwave energy must be below the
limit of 5 mW/cm.sq. (with a 275 ml water load)
3. When mounting the door assembly to the oven assembly, be
sure to adjust the door assembly parallel to the chassis. Also
adjust so the door has no play between the inner door surface
and oven frame assembly. If the door assembly is not
mounted properly, microwaves may leak from the clearance
between the door and the oven.
-13-
D. MAGNETRON REMOVAL (Figure 10) E. REMOVING THE TURNTABLE MOTOR (Figure 11)
1) Disconnect the wire lead from the magnetron. 1) Remove the turntable and rotating ring.
2) Carefully remove the mounting screws holding the 2) Lay the unit down on its back.
magnetron and the waveguide. 3) Remove the turntable motor cover.
3) Remove the magnetron assembly until the tube is clear The turntable base cover is easily removed by pinching
from the waveguide. the eight parts with a wire cutting.
4) Disconnect the leadwire from the turntable motor
NOTE: terminals.
1. When removing the magnetron, make sure its dome 5) Remove the screw securing the turntable motor to the
does not hit any adjacent parts, or it may be damaged. oven cavity ASSEMBLY.
2. When replacing the magnetron, be sure to install the 6) After repairing the motor, rotate the removed turntable
magnetron gasket in the correct position and be sure motor cover.
that the gasket is in good condition. 7) Fit the turntable motor cover’s projecting part to the base
3. After replacing the magnetron, check for microwave plate slit.
leakage with a survey meter around the magnetron.
Microwave energy must be below the limit of 5 mW/cm2. NOTE:
(With a 275 ml. water load). 1. Remove the wire lead from the turntable motor VERY
Make sure that gasket is rigidly attached to the CAREFULLY.
magnetron. To prevent microwave leakage, tighten the 2. Be sure to grasp the connector, not the wires, when
mounting screws properly, making sure there is no gap removing.
between the waveguide and the magnetron.
Magnetron
Waveguide
Dome
Waveguide Turntable
Motor Wire Leads
Bracket
Magnetron
Gasket
Magnetron
-14-
F. HIGH VOLTAGE TRANSFORMER REMOVAL I. INTERLOCK SYSTEM
1) Discharge the high voltage capacitor. 1) INTERLOCK MECHANISM
2) Disconnect the leadwire from magnetron, high voltage The door lock mechanism is a device which has been
transformer, and capacitor. specially designed to eliminate completely microwave
3) Remove the screw holding the high voltage transformer to activity when the door is opened during cooking and thus
the baseplate. to prevent the danger resulting from the microwave
leakage.
G. FAN MOTOR ASSEMBLY REMOVAL
2) MOUNTING OF THE PRIMARY/MONITOR/
1) Discharge the high voltage capacitor.
SECONDARY SWITCHES TO THE LATCH BOARD
2) Disconnect the leadwire from fan motor and high voltage
3) INSTALLATION AND ADJUSTMENT OF THE LATCH
capacitor.
BOARD TO THE OVEN ASSEMBLY
3) Remove the two screws holding the the suction guide
• Mount the latch board to the oven assembly.
ASSEMBLY to the oven cavity.
• Adjust the latch board in the arrow direction so that oven
4) Remove the two screws holding the fan motor ASSEMBLY
door will not have any play in it when the door is closed.
to the suction guide ASSEMBLY.
• Tighten the mounting screw.
H. HIGH VOLTAGE CAPACITOR AND DIODE REMOVAL • Check for play in the door by pushing the door
release button. Door movement should be less than
1) Discharge the high voltage capacitor. 0.5 mm. (1/64 inch)
2) Disconnect the leadwire from fan motor and high voltage Don't push the door release button while making this
capacitor. adjustment. Make sure that the latch moves smoothly after
3) Remove the screw holding the suction guide ASSEMBLY to adjustment is completed and that the screws are tight.
the oven cavity. Make sure the primary, monitor, and secondary switches
4) Remove the screw holding the high voltage capacitor operate properly by following the continuity test
bracket and remove the high voltage diode earth screw. procedure.
-15-
10. INTERLOCK CONTINUITY TEST
Primary
NO
Switch COM
Monitor NC
Switch COM
Secondary
Switch COM
NO
NOTE : After checking for the continuity of switches, make sure that they are
connected correctly.
-16-
11. TEST AND CHECKOUT PROCEDURES, AND TROUBLESHOOTING
CAUTIONS
1. DISCONNECT THE POWER SUPPLY CORD FROM THE OUTLET WHENEVER REMOVING THE OUTER CASE
FROM THE UNIT. PROCEED WITH THE TEST ONLY AFTER DISCHARGING THE HIGH VOLTAGE CAPACITOR
AND REMOVING THE WIRE LEADS FROM THE PRIMARY WINDING OF THE HIGH VOLTAGE
TRANSFORMER.
2. ALL OPERATIONAL CHECKS WITH MICROWAVE ENERGY MUST BE DONE WITH A LOAD (1 LITER OF
WATER IN CONTAINER) IN THE OVEN.
A. TEST PROCEDURES
HIGH VOLTAGE
TRANSFORMER
(Wire leads removed)
FILAMENT
WINDING
PRIMARY
TERMINAL
SECONDARY
WINDING
-17-
COMPONENTS TEST PROCEDURE RESULTS
Antenna
Gasket
Chassis
Filament
NOTE: When testing the magnetron, be sure to install the magnetron gasket in the
correct position and be sure that the gasket is in good condition.
-18-
COMPONENTS TEST PROCEDURE RESULTS
-19-
COMPONENTS TEST PROCEDURE RESULTS
Abnormal:
Infinite
NOTE : • A MICROWAVE LEAKAGE TEST MUST ALWAYS BE PERFORMED WHEN THE UNIT IS SERVICED FOR ANY
REASON.
• MAKE SURE THE WIRE LEADS ARE IN THE CORRECT POSITION.
• WHEN REMOVING THE WIRE LEADS FROM THE PARTS, BE SURE TO GRASP THE CONNECTOR, NOT THE
WIRES.
-20-
B. CHECKOUT PROCEDURES
(1) CHECKOUT PROCEDURES FOR FUSE BLOWING
PROBLEMS CAUSES
Fuse blows when the door is closed and START key Malfunction of the high voltage transformer; the high
is touched. voltage capacitor including the diode, the magnetron,
the blower motor or the circuit board.
NOTES:
- If the fuse is blown by an improper switch operation, replace the defective switches and the fuse at the same time.
After replacing the defective switches with new ones, make sure that they are correctly connected.
- Check for microwave energy leakage according to “1. ADJUSTMENT PROCEDURES” on page 3, when the
primary interlock, secondary interlock switches and/or the interlock monitor switches are adjusted or replaced.
-21-
(2) CHECKOUT PROCEDURES FOR RELAY.
NO YES NO YES
GOOD Remove the mate connector of I/O GOOD Remove the mate connector of I/O
CON from the circuit board does CON from the circuit board does
the unit still operate? the unit still operate?
NO NO
YES NO YES NO
GOOD Check the interlock switches GOOD Check the interlock switches
NO YES NO YES
Replace Replace
RELAY or correct RELAY or correct
the connection. the connection.
-22-
(3) CHECKOUT PROCEDURES FOR CIRCUIT BOARD
The following symptoms indicate a defective circuit
board.
(1) The start function fails to operate but the high (4) Some segments of one or more digits do not light up, or
voltage Systems, the interlock switches, the door they continue to light up, or segments light when they
sensing and the relay check good. should not.
(2) The unit with a normal relay continuously operates. (6) Wrong figures appear.
(3) The buzzer does not sound or continues to sound. (7) The figures of all digits flicker.
(8) Some of the indicators do no light up.
(9) The clock does not keep time properly.
NOTE: A MICROWAVE ENERGY LEAKAGE TEST MUST ALWAYS BE PERFORMED WHEN THE UNIT IS
SERVICED FOR ANY REASON.
-23-
C. TROUBLE SHOOTING
WHEN YOU GET A COMPLAINT FROM YOUR CUSTOMER, EVALUATE THE COMPLAINT CAREFULLY. IF THE
FOLLOWING SYMPTOMS APPLY, PLEASE INSTRUCT THE CUSTOMER IN THE PROPER USE OF THE TOASTER AND
MICROWAVE OVEN. THIS CAN ELIMINATE AN UNNECESSARY SERVICE CALL.
CAUTIONS
1. Check grounding and cool this unit before checking for trouble.
2. Be careful of the high voltage circuit.
3. Discharge the high voltage capacitor.
4. When checking the continuity of the switches or of the high voltage transformer, disconnect one lead wire from these
parts and then check continuity with the AC plug removed. To do otherwise may result in a false reading or damage
to your meter.
5. Do not touch any part of the circuit on the PCB since static electric discharge may damage this control panel.
Always touch yourself to ground while working on this panel to discharge any static charge built up in your body.
(Micom model only)
Toaster and Microwave oven Inserting many plugs into one Avoid using other electrical
does not work. outlet and using them at the appliances when you use this
same time unit.
(blown fuse or breaker)
Output power is too low. Low AC input voltage. Use the this machine at
adequate line voltage.
Sparks occur in oven. Using metallic ware and Do not use metallic ware for
allowing it to touch the oven cooking except where noted
wall. in the cooking guide.
-24-
(TROUBLE 1) The following visual conditions indicate a probable defective control circuit.
1. Incomplete segments.
• Segment missing.
• Partial segment missing.
• Digit flickering (NOTE: Slight flickering is normal.)
2. Colon does not turn on or blink.
3. A distinct change in the brightness of one or more numbers in display.
4. One or more digits in the display are not lighting.
5. Display indicates a number different from one touched, for example, key in 5 and 3 appears in the display.
6. Specific numbers (for example 7 or 9) will not display when key pad is touched.
7. Display does not count down with time blinking or up with clock operation.
8. Display obviously jumps in time while counting down.
9. Display counts down too fast while cooking.
10. Each indicator light does not turn on after setting cooking cycle.
11. Display time of day does not reappear when cooking is finished.
2. Some inputs Replace key Everything works Defective key Replace key
cannot be membrane as specified. membrane membrane
programmed. assembly and assembly. assembly.
check operation.
4. Random
programming
when touching
other pads.
5. Display is fixed
at some figure
and can not
accept any
input.
-25-
(TROUBLE 2) Microwave oven does not operate at all, Display window does not display any figures,
and no input is accepted.
Replace fuse
Continuity.
-26-
(TROUBLE 3) Display shows all figures set, but microwave oven does not start cooking while desired
program times are set and START pad is touched.
2. Fan motor or Check fan motor. Abnormal Defective fan motor. Replace fan motor.
oven lamp do
not turn on. Check oven lamp. Abnormal Defective oven lamp. Replace oven lamp.
Normal
(TROUBLE 4) Microwave oven seems to be operating but little heat is produced in oven load.
NOTE: Simple test of power output-conducted by heating one liter water for one min. if available.
Minimum 8.5oC temperature rise is normal condition.
-27-
(TROUBLE 5) No microwave oscillation even though oven lamp and fan motor run.
(Display operates properly)
Normal
Normal
-28-
(TROUBLE 6) When toaster operates, strange code can be seen on the display and stop with beep sound.
Continuity.
-29-
EXPLODED VIEW
INTRODUCTION
-30-
DOOR PARTS
13552A 15006A
13581A
13536A
13213A
14890A
14026A
14970A
WTP004
268712
WTT028
13720D
13650A
-31-
OVEN CAVITY PARTS
33112U WSZ185
33052A
For model
LTRM1240SW
WTT010 LTRM1240ST
33390G
35889A
36549S
WTP013
-32-
LATCH BOARD PARTS
WSZ085
56912B
466001
43500A 466003
55262A
466001
44510A
-33-
OVEN INTERIOR PARTS
WSZ002
56411A
568771
WTT024 50FZZA
56930V
268711
55006F
WTT028 568772
56549F
54974S
WSZ002
55900A
WTT037
50CZZH
WSZ002
WSZ002 34930W
54810C 56851D
35012A
WTT028
56324A
WSZ002
-34-
BASE PLATE PARTS
56170D
63302A
63303A
65006A 647781
WTT021
WTT028
WSZ002
WTT021
-35-
SENSOR PARTS
WTP004 WTT021
56501A
54974T
-36-
COFFEE MAKER PARTS
75993M
76322A
76930V
73550L 768711
74970A
73650A 766001
74510L
73740A
73720D
73551B 73213A 73572A
73552A
73551A
73551C
For LTRM1240ST
For LTRM1240ST
-37-