Professional Documents
Culture Documents
Microwave Oven: Service Manual
Microwave Oven: Service Manual
정 판
MICROWAVE OVEN
SERVICE MANUAL
MODEL: MH-6387AR
CAUTION
BEFORE SERVICING THE UNIT, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
August, 2007
P/NO : MFL32188507 Printed in Korea
SAFETY PRECAUTIONS
This device is to be serviced only by properly qualified service personnel.
Consult the service manual for proper service procedures to assure continued safety operation and for precautions to be
taken to avoid possible exposure to excessive microwave energy.
CAUTION
MICROWAVE RADIATION
DO NOT BECOME EXPOSED TO RADIATION FROM THE MICROWAVE GENERATOR
OR OTHER PARTS CONDUCTING MICROWAVE ENERGY.
Copyright © 2007 LG Electronics. Inc. All right reserved. LGE Internal Use Only
Only for training and service purposes
CONTENTS
(Page)
SPECIFICATIONS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1-1
CAUTIONS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-1
INSTALLATIONS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-1
FEATURES- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-1
LGE Internal Use Only Copyright © 2007 LG Electronics. Inc. All right reserved.
Only for training and service purposes
SPECIFICATIONS
ITEM DESCRIPTION
MODEL MH-6387AR
Power Requirement 230 Volts AC 50 Hz
Single phase, 3 wire grounded
Microwave 1250W
Grill 1000W
Combi 2200W
Power Output 850 Watts full microwave power (IEC60705)
Microwave Frequency 2450 MHz
Magnetron 2M167B - M47J1
Timer 0 ~ 99 Min.
Outside Dimensions 507 (W) x 283 (H) x 435 (D) mm
Cavity Dimensions 331 (W) x 203 (H) x 360 (D) mm
Net Weight 14.5 kg (approx.)
Shipping weight 16.5 kg (approx.)
Control Complement Microwave Power for Variable Cooking
Power level
MAX .................................................. Full power throughout the cooking time
MED.-HIGH......................................... approx. 80% of Full power
MEDIUM ............................................. approx. 60% of Full power
DEFROST........................................... approx. 40% of Full power
LOW/WARM........................................ approx. 20% of Full power
Copyright © 2007 LG Electronics. Inc. All right reserved. 1-1 LGE Internal Use Only
Only for training and service purposes
CAUTIONS
ANTENNA
Gasket
COOLING FIN
FILAMENT
TERMINALS
MAGNETRON
CHASSIS GROUND
LGE Internal Use Only 2-1 Copyright © 2007 LG Electronics. Inc. All right reserved.
Only for training and service purposes
INSTALLATIONS
BEFORE YOU BEGIN, READ THE FOLLOWING INSTRUCTIONS COMPLETELY AND CAREFULLY.
Copyright © 2007 LG Electronics. Inc. All right reserved. 3-1 LGE Internal Use Only
Only for training and service purposes
OPERATING INSTRUCTIONS
FEATURES
Oven Front Plate
Window Door Screen
Door Seal
Control Panel
HIGH RACK
GLASS TRAY
CONTROL PANEL
12
LGE Internal Use Only 4-1 Copyright © 2007 LG Electronics. Inc. All right reserved.
Only for training and service purposes
OPERATING SEQUENCE
The following is a description of component functions 7. COMBI COOKING
during oven operation.
Clear Combi Time Quick Start
1. SETTING THE CLOCK
2. CANCEL FUNCTION
Touch the Clear pad whenever you need to
cancel an entry or a function currently in use.
The display will either return to the last item entered
or to the clock.
3. CHILD LOCK
This oven has a CHILD LOCK feature.
• TO SET CHILD LOCK
• Touch the Clear pad
• Touch Clear pad L appear in
the display.
4. QUICK START
5. MICROWAVE COOKING
6. GRILL COOKING
Copyright © 2007 LG Electronics. Inc. All right reserved. 4-2 LGE Internal Use Only
Only for training and service purposes
SCHEMATIC DIAGRAM
LGE Internal Use Only 4-3 Copyright © 2007 LG Electronics. Inc. All right reserved.
Only for training and service purposes
CIRCUIT DESCRIPTION
GENERAL DETAILS power of microwave oven as POWER LEVEL.
(refer to page 1-1)
• The low voltage transformer supplies the necessary
voltage to the micom controller when power cord is WHEN THE DOOR IS OPENED DURING
plugged in. COOKING
• When the door is closed, the primary switch is ON, the
secondary switch is ON, and the monitor switch opens • Both the primary switch and relay 2 are cut off primary
(contact COM and NO). winding voltage of the high voltage transformer.
• ON-OFF of relay 2 is coupled electrically with opening
WHEN SELECTING COOKING POWER and closing of the secondary switch.
LEVEL AND TIME • When the door is opened, the secondary switch is
opened and when the door is closed, the secondary
• The micom controller memorizes the function you set. switch is closed.
• The time you set appears in the display window. • The cooking time stops counting down.
• Each indicator light turns on to indicate that the stage • Relay stops functioning.
has been set. • As the door is opened, if the contact of primary switch
and relay 2 and/or secondary switch fails to open, the
WHEN TOUCHING THE START PAD fuse opens due to the large current surge caused by
• The coil of the relay is energized by the micom the monitor switch activation, which in turn stops
controller. magnetron oscillation.
• Power input is supplied to the high voltage transformer
PRIMARY
through the fuse to the primary switch and relay 2. FUSE SWITCH
• Turntable rotates.
PRIMARY L
FUSE SWITCH H.V.
MONITOR TRANS-
SWITCH FORMER
L N
H.V.
MONITOR TRANS-
SWITCH FORMER
RELAY 2 SECONDARY
N SWITCH
MICOM CONTROLLER
RELAY 2 SECONDARY
SWITCH
MICOM CONTROLLER
WHEN TOUCHING THE START KEY
WITH THE GRILL COOKING FUNCTION
• The fan motor rotates and cools the magnetron by SELECTED
blowing the air (coming from the intake on the
baseplate). • The contacts of the primary switch and the secondary
• The air is also directed into the oven to exhaust the switch close the circuit.
vapor in the oven through the upper plate. • A.C. voltage is applied to the grill heater through grill
• Cooking time starts counting down. thermostat as shown by the solid line.
• 3.2 volts AC is generated from the filament winding of GRILL
the high voltage transformer. This 3.2 volts is applied to THERMOSTAT
the magnetron to heat the magnetron filament through
two noise-preventing choke coils.
L
• A high voltage of approximately 2100 volts AC is L
generated in the secondary of the high voltage G -Y
E GRILL
N HEATER
transformer which is increased by the action of the high N
voltage diode and charging of the high voltage
capacitor.
• The negative 4000 Volts DC is applied to the filament RELAY 3
of the magnetron.
• Turntable rotates.
WHEN THE OVEN IS SET AT ANY LEVEL • The fan motor rotates.
EXCEPT MAXIMUM. • The air is also directed into the oven to exhaust the
• The micom controller controls the ON-OFF time of relay vapor in the oven through the base plate and upper
2 by the applied signal to vary the average output plate.
Copyright © 2007 LG Electronics. Inc. All right reserved. 4-4 LGE Internal Use Only
Only for training and service purposes
SERVICE INFORMATION
TOOLS AND MEASURING INSTRUMENTS
NECESSARY TOOLS NECESSARY MEASURING INSTRUMENTS
Tools normally used for TV servicing are sufficient. • TESTER(VOLTS-DC, AC., Ohmmeter)
Standard tools are listed below. • Microwave survey meter
• Diagonal pliers - Holaday HI-1500
• Long nose pliers HI-1501
• Phillips screwdriver - Narda 8100
• Flat blade screwdriver 8200
• Wrench (size 5mm) • Inch scale
• Nutdriver (size 5mm) • 600 cc non conductive material beaker (glass or plastic),
• Adjustable wrench inside diameter: approx. 8.5 cm(31/2 in.)
• Soldering iron • Cylindrical and made of borosilicate glass vessel.
• Solder max. thickness: 3 mm
• Vinyl insulation tape outside diameter: approx. 190mm
• Polishing cloth height: approx. 90mm
• Glass thermometer: 100°C or 212°F (1 deg scale)
LGE Internal Use Only 5-1 Copyright © 2007 LG Electronics. Inc. All right reserved.
Only for training and service purposes
MEASUREMENT WITH OUTER CASE NOTES WHEN MEASURING
REMOVED • Do not exceed meter full scale deflection.
• When you replace the magnetron, measure for • The test probe must be removed no faster than
microwave energy leakage before the outer case is 1 inch/sec (2.5 cm/sec) along the shaded area,
installed and after all necessary components are otherwise a false reading may result.
replaced or adjusted. • The test probe must be held with the grip portion of the
Special care should be taken in measuring the handle.
following parts. (Circled area of below Fig.) A false reading may result if the operator's hand is
- Around the magnetron between the handle and the probe.
- The waveguide • When testing near a corner of the door, keep the probe
perpendicular to the surface making sure the probe
horizontally along the oven surface, this may possibly
WARNING : AVOID CONTACTING ANY cause probe damage.
HIGH VOLTAGE PARTS
(Magnetron, H.V. Transformer, RECORD KEEPING AND NOTIFICATION
H.V. Capacitor, H.V. Cable Ass’y, AFTER MEASUREMENT
H.V. Circuit Protector) • After adjustment and repair of any microwave energy
interruption or microwave energy blocking device,
record the measured values for future reference. Also
enter the information on the service invoice.
• The microwave energy leakage should not be more
than 4 mW/cm.sq. after determining that all parts are in
good condition, functioning properly and genuine
replacement parts which are listed in this manual have
been used.
• At least once a year, have the electromagnetic energy
leakage monitor checked for calibration by its
manufacturer.
Copyright © 2007 LG Electronics. Inc. All right reserved. 5-2 LGE Internal Use Only
Only for training and service purposes
MEASUREMENT OF MICROWAVE POWER OUTPUT
• Microwave power output measurement is made with • The microwave power output P in watts is calculated
the microwave oven supplied at its rated voltage and from the following formula :
operated at its maximum microwave power setting with 4187 X (∆T) + 0.55 X (T2 - T0 ) X M
a load of (1000 ± 5)g of potable water. P=
• The water is contained in a cylindrical borosilicate glass T
vessel having a maximum material thickness of 3 mm • T2 : Temperature after heating
and an outside diameter of approximately 190 mm. • T0 : Temperature after bown
• The oven and the empty vessel are at ambient • M : Weight of bowl
temperature prior to the start of the test.
• The initial temperature (T1) of the water is (10±2)°C.It is measured while the microwave generator is
is measured immediately before the water is added to operating at full power. Magnetron filament heat-up
the vessel. After addition of the water to the vessel, time is not included. (about 3 sec)
the load is immediately placed on the center of the • The water is stirred, to equalize temperature throughout
turntable which is in the lowest position and the the vessel, prior to measuring the final water
microwave power switched on. temperature.
• The time T for the temperature of the water to rise by a • Stirring devices and measuring instruments are
value ∆T of (10±2)°K is measured, where T is the time selected in order to minimize addition or removal of
in seconds and ∆T is the temperature rise. The initial heat.
and final water temperatures are selected so that the
maximum difference between the final water WATER LOAD
temperature and the ambient temperature is 5°K.
TURNTABLE
LGE Internal Use Only 5-3 Copyright © 2007 LG Electronics. Inc. All right reserved.
Only for training and service purposes
D. DOOR GROSS ASSEMBLY REMOVAL E. HIGH VOLTAGE TRANSFORMER
1) Open the door. REMOVAL
2) Remove the choke cover cap very carefully with a
1) Discharge the high voltage capacitor.
flat-blade screwdriver.
2) Disconnect the leadwire from magnetron, high voltage
CAUTION : Be careful not to damage door seal plate
transformer, and capacitor.
by screwdriver.
3) Remove the screw holding the high voltage
3) Lift up and push the door.
transformer to the baseplate.
NOTE:
1. After replacing the door, be sure to check that the F. FAN MOTOR ASSEMBLY REMOVAL
primary switch, monitor switch, and secondary switch
1) Discharge the high voltage capacitor.
operate normally.
2) Disconnect the leadwire from fan motor, noise filter
2. After replacing the door, check for microwave energy
and high voltage capacitor.
leakage with a survey meter. Microwave energy must
3) Remove the two screws holding the the suction guide
be below the limit of 5 mW/cm. (with a 275 ml water
ASS’Y to the oven cavity and remove the high voltage
load)
diode earth screw.
3. When mounting the door assembly to the oven
4) Remove the screw of the capacitor bracket.
assembly, be sure to adjust the door assembly parallel
5) Remove the two screws holding the fan motor ASS’Y
to the chassis. Also adjust so the door has no play
to the suction guide ASS’Y.
between the inner door surface and oven frame
assembly. If the door assembly is not mounted
properly, microwaves may leak from the clearance G. HIGH VOLTAGE CAPACITOR AND
between the door and the oven. DIODE REMOVAL
Remove Hinge Plate 1) Discharge the high voltage capacitor.
2) Disconnect the leadwire from fan motor, noise filter
and high voltage capacitor.
3) Remove the screw holding the suction guide ASS’Y to
the oven cavity and remove the high voltage diode
earth screw.
4) Remove the screw holding the high voltage capacitor
bracket.
Fan Motor ASS Y
Suction
Guide
H.V
Transformer H.V.
Diode
Copyright © 2007 LG Electronics. Inc. All right reserved. 5-4 LGE Internal Use Only
Only for training and service purposes
H. AIR DUCT ASSEMBLY REMOVAL J. REMOVING THE TURNTABLE MOTOR
1) Disconnect the leadwire from lamp. 1) Remove the turntable.
2) Remove the mounting screw to Latch Board. 2) Remove the Rotating Ring.
3) Lay the unit down on its back.
4) Remove the turntable motor cover.
I. MAGNETRON REMOVAL The turntable base cover is easily removed by
pinching the six parts with a wire cutting.
1) Disconnect the leadwire from the high voltage
5) Disconnect the leadwire from the turntable motor
transformer and high voltage capacitor.
terminals.
2) Carefully remove the mounting screws holding the
6) Remove the screw securing the turntable motor to
magnetron and the waveguide.
the oven cavity ASS’Y
3) Remove the magnetron ASS’Y until the tube is
7) After repairing the motor, rotate the removed
clear from the waveguide.
turntable motor cover.
NOTE: 8) Fit the turntable motor cover’s projecting part to the
1. When removing the magnetron, make sure its base plate slit.
dome does not hit any adjacent parts, or it may be 9) The taptite screw shall be used when a turntable
damaged. motor cover is secured with a screw.
2. When replacing the magnetron, be sure to install
the magnetron gasket in the correct position and NOTE:
be sure that the gasket is in good condition. 1. Remove the wire lead from the turntable motor
3. After replacing the magnetron, check for microwave VERY CAREFULLY.
leakage with a survey meter around the 2. Be sure to grasp the connector, not the wires, when
magnetron. Microwave energy must be below the removing
limit of 5 mW/cm2. (With a 275 ml. water load).
Make sure that gasket is rigidly attached to the
magnetron. To prevent microwave leakage,
tighten the mounting screws properly, making sure
there is no gap between the waveguide and the
magnetron.
Magnetron
Dome
Waveguide
Bracket
Wire Leads
Magnetron
Gasket
Magnetron Turntable Motor
LGE Internal Use Only 5-5 Copyright © 2007 LG Electronics. Inc. All right reserved.
Only for training and service purposes
K. PCB ASSEMBLY REMOVAL L. INTERLOCK SYSTEM
1) Remove the control panel assembly from the 1) INTERLOCK MECHANISM
cavity. (Refer to control panel assembly removal The door lock mechanism is a device which has
on previous page.) been specially designed to eliminate completely
2) Remove screws which hold the PCB SUB ASS’Y to microwave activity when the door is opened during
the control panel. cooking and thus to prevent the danger resulting
3) Disconnect the flat cable from the PCB SUB from the microwave leakage.
ASS’Y and take off the PCB SUB ASS’Y.
2) MOUNTING OF THE PRIMARY/MONITOR
SECONDARY SWITCHES TO THE LATCH BOARD.
ADJUSTMENT
DIRECTION
PRIMARY
SWITCH
MONITOR
SWITCH
SECONDARY
SWITCH
H.V. TRANSFORMER
H.V.
DIODE
H.V. CAPACITOR
Copyright © 2007 LG Electronics. Inc. All right reserved. 5-6 LGE Internal Use Only
Only for training and service purposes
INTERLOCK CONTINUITY TEST
WARNING : FOR CONTINUED PROTECTION AGAINST EXCESSIVE RADIATION
EMISSION, REPLACE ONLY WITH IDENTICAL REPLACEMENT PARTS.
TYPE NO. SZM-V 16-FA-63 OR VP-533A-OF FOR PRIMARY SWITCH
TYPE NO. SZM-V 16-FA-62 OR VP-532A-OF FOR MONITOR SWITCH
TYPE NO. SZM-V 16-FA-63 OR VP-533A-OF FOR SECONDARY SWITCH
Primary NO
Switch COM
Monitor NC
Switch COM
Secondary
NO
Switch COM
NOTE : After checking for the continuity of switches, make sure that are
connected correctly.
LGE Internal Use Only 5-7 Copyright © 2007 LG Electronics. Inc. All right reserved.
Only for training and service purposes
COMPONENT TEST PROCEDURE
CAUTIONS
1. DISCONNECT THE POWER SUPPLY CORD FROM THE OUTLET WHENEVER REMOVING THE
OUTER CASE FROM THE UNIT. PROCEED WITH THE TEST ONLY AFTER DISCHARGING THE HIGH
VOLTAGE CAPACITOR AND REMOVING THE WIRE LEADS FROM THE PRIMARY WINDING OF THE
HIGH VOLTAGE TRANSFORMER. (SEE PAGE 2-1)
2. ALL OPERATIONAL CHECKS WITH MICROWAVE ENERGY MUST BE DONE WITH A LOAD (1 LITER
OF WATER IN CONTAINER) IN THE OVEN.
SECONDARY
TERMINAL
PRIMARY
TERMINAL
1. Measure the resistance.
(Ohm-meter scale: Rx1 and Rx100)
• Primary winding Approx.: 2.5 Ω
• Secondary winding Approx.: 110 Ω
• Filament winding Less than: 0.4 Ω
MAGNETRON
(Wire leads removed)
1. Measure the resistance.
(Ohm-meter scale: Rx1) Normal: Less than 1 Ω
• Filament terminal
Copyright © 2007 LG Electronics. Inc. All right reserved. 5-8 LGE Internal Use Only
Only for training and service purposes
COMPONENTS TEST PROCEDURE RESULTS
Antenna
Gasket
Chassis
Filament
NOTE: When testing the magnetron, be sure to install the magnetron gasket
in the correct position and be sure that the gasket is in good condition.
NOTE :
Some inexpensive meters
may indicate infinite
resistance in both direction. Measure the continuity (Reverse). Normal: ∞
(Ohm-meter scale: Rx10000) Abnormal: Continuity.
LGE Internal Use Only 5-9 Copyright © 2007 LG Electronics. Inc. All right reserved.
Only for training and service purposes
COMPONENTS TEST PROCEDURE RESULTS
FUSE Check for continuity of the fuse with an Normal Abnormal
multi-meter.
NOTE: If the fuse is blown, check the primary, the secondary, and the monitor switches,
H.V.D. and H.V.C. before replacing the fuse.
If the fuse is blown by improper switch operation replace the defective switch and the
fuse at the same time. Replace just the fuse if the switches operate normally.
H.V. FUSE Check for continuity of the H.V.Fuse with Normal Abnormal
multi-meter.
Measure the resistance with 500V-100M ohm Normal: more than 0.5 Mohm
insulation resistance meter.
OVEN THERMOSTAT
MAGNETRON
THERMOSTAT 0°C~Approx.145°C Approx.145°C
Copyright © 2007 LG Electronics. Inc. All right reserved. 5-10 LGE Internal Use Only
Only for training and service purposes
COMPONENTS TEST PROCEDURE RESULTS
Disconnect the 8 pin Check for P.C.B. connector. Cooking Start OFF
connector from P.C.B.
(Refer to schemetic diagram)
1 3 5
40 ~ 60Ω 300~500 Ω
Abnormal: ∞ or several Ω
A
B
C
NOTE : • A MICROWAVE LEAKAGE TEST MUST ALWAYS BE PERFORMED WHEN THE UNIT IS
SERVICED FOR ANY REASON.
• MAKE SURE THE WIRE LEADS ARE IN THE CORRECT POSITION.
• WHEN REMOVING THE WIRE LEADS FROM THE PARTS, BE SURE TO GRASP THE
CONNECTOR, NOT THE WIRES.
LGE Internal Use Only 5-11 Copyright © 2007 LG Electronics. Inc. All right reserved.
Only for training and service purposes
TROUBLE SHOOTING
WHEN YOU GET A COMPLAINT FROM YOUR CUSTOMER, EVALUATE THE COMPLAINT CAREFULLY. IF
THE FOLLOWING SYMPTOMS APPLY, PLEASE INSTRUCT THE CUSTOMER IN THE PROPER USE OF THE
MICROWAVE OVEN. THIS CAN ELIMINATE AN UNNECESSARY SERVICE CALL.
CAUTIONS
1. Check grounding before checking for trouble.
2. Be careful of the high voltage circuit.
3. Discharge the high voltage capacitor. (See page 2-1)
4. When checking the continuity of the switches or of the high voltage transformer, disconnect one lead wire
from these parts and then check continuity with the AC plug removed. To do otherwise may result in a
false reading or damage to your meter.
5. Do not touch any part of the circuitry on the digital programmer circuit since static electric discharge may
damage this control panel.
Always touch yourself ground while working on this panel to discharge any static charge built up in your
body.
Microwave oven Inserting many plug into one Avoid using other electrical
does not work. plug outlet and using appliances when you use the
them at the same time microwave oven.
(causes overloading).
Output power is too low. Low AC input voltage. Use the microwave oven at
adequate line voltage.
Sparks occurring. Using metallic ware and Do not use metallic ware for
allowing it to touch the oven cooking except where noted
wall. in the cooking guide.
Copyright © 2007 LG Electronics. Inc. All right reserved. 5-12 LGE Internal Use Only
Only for training and service purposes
(TROUBLE 1) Oven lamp does not turn on when the timer knob is pushed with door closed.
1. Incomplete segments.
• Segment missing.
• Partial segment missing.
• Digit flickering (NOTE: Slight flickering is normal.)
2. Colon does not turn on or blink.
3. A distinct change in the brightness of one or more numbers in display.
4. One or more digits in the display are not lighting.
5. Display indicates a number different from one touched, for example, key in 5 and 3 appears in the display.
6. Specific numbers (for example 7 or 9) will not display when key pad is touched.
7. Display does not count down with time blinking or up with clock operation.
8. Display obviously jumps in time while counting down.
9. Display counts down too fast while cooking.
10. Each indicator light does not turn on after setting cooking cycle.
11. Display time of day does not reappear when cooking is finished.
12. Beep sound is not heard when correct key is touched.
2. Some inputs Replace key Everything works Defective key Replace key
cannot be membrane as specified. membrane membrane
programmed. assembly and assembly. assembly.
check operation.
4. Random
programming
when touching
other pads.
5. Display is fixed
at some figure
and can not
accept any
input.
LGE Internal Use Only 5-13 Copyright © 2007 LG Electronics. Inc. All right reserved.
Only for training and service purposes
(TROUBLE 2) Oven does not operate at all ; Display window does not display any figures and
no input is accepted.
Replace fuse
NOTE : All these switches must be replaced at the same time. Refer to page 5-6, 5-7
Copyright © 2007 LG Electronics. Inc. All right reserved. 5-14 LGE Internal Use Only
Only for training and service purposes
(TROUBLE 3) Display shows all figures set, but oven does not start cooking while
desired program times are set and START pad is touched.
Check continuity
of secondary Defective P.C.B Replace P.C.B
No continuity.
switch (with assembly. assembly.
door closed).
Connection then
Continuity. Loose connection.
tightly.
Normal.
(TROUBLE 4) Oven seems to be operation but little heat is produced in oven load.
Disconnect the
wire leads from Abnormal. Defective P.C.B Replace P.C.B
relay 2 and check assembly. assembly.
on and off time
with multitester. Abnormal.
NOTE: Simple test of power output-conducted by heating one liter water for one min. if available.
LGE Internal Use Only 5-15 Copyright © 2007 LG Electronics. Inc. All right reserved.
Only for training and service purposes
(TROUBLE 5) No microwave oscillation even though oven lamp and fan motor run
(Display operates properly)
normal
normal
Copyright © 2007 LG Electronics. Inc. All right reserved. 5-16 LGE Internal Use Only
Only for training and service purposes
(TROUBLE 6) Oven does not cook properly when programmed for the set power level
(Operates properly on HIGH)
(TROUBLE 7) Grill
Normal.
Normal.
Replace or
Wire connection. No continuity. Open or loosen.
connect tightly.
Normal.
LGE Internal Use Only 5-17 Copyright © 2007 LG Electronics. Inc. All right reserved.
Only for training and service purposes
#EV#
EXPLODED VIEW
INTRODUCTION
MODEL: MH-6387AR
INTERIOR PARTS
Copyright © 2007 LG Electronics. Inc. All right reserved. -6-1- LGE Internal Use Only
Only for training and service purposes
#EV#
DOOR PARTS
13581A
13536A
13552A
13213A
13720D
14890A
14026A
WTT028
14970A
13650A
LGE Internal Use Only -6-2- Copyright © 2007 LG Electronics. Inc. All right reserved.
Only for training and service purposes
#EV#
268711 WTP013
268712
23572A 25020M
23806C
WTP004
249401
243501
25020S
24781S
Copyright © 2007 LG Electronics. Inc. All right reserved. -6-3- LGE Internal Use Only
Only for training and service purposes
#EV#
WNH001
348102
WTT021
WTP004
348101
44360A
348101
WTT020
WTT011
33052M 33112U
35026G
4980W1A058B
35026C
368771
33390G
35300A 36549S
34370T
WTP013 35889A
LGE Internal Use Only -6-4- Copyright © 2007 LG Electronics. Inc. All right reserved.
Only for training and service purposes
#EV#
43501A
43500A
466001
466003
466001
44510A
WSZ085
Copyright © 2007 LG Electronics. Inc. All right reserved. -6-5- LGE Internal Use Only
Only for training and service purposes
#EV#
INTERIOR PARTS
568771
WSZ062
56411A
56930V
50FZZA
WSZ002 54974S
55900A
WTT037
WSZ002 50CZZH
WTP004
56930G
56912B
WSZ002
948501
56851C
55262A
54810C
WTT028
56324A
WSZ002
LGE Internal Use Only -6-6- Copyright © 2007 LG Electronics. Inc. All right reserved.
Only for training and service purposes
#EV#
56170D
63302A
63303A
65006B
WSZ002
WTT021
Copyright © 2007 LG Electronics. Inc. All right reserved. -6-7- LGE Internal Use Only
Only for training and service purposes