Professional Documents
Culture Documents
Pressure Testing of Valves: MSS SP-61-2019
Pressure Testing of Valves: MSS SP-61-2019
Pressure Testing
of Valves
Standard Practice
Developed and Approved by the
Manufacturers Standardization Society of the
Valve and Fittings Industry, Inc.
127 Park Street, NE
Vienna, Virginia 22180-4602
www.msshq.org
Phone:revision.
(703) 281-6613
Fax: (703) 281-6671
E-mail: [email protected]
MSS STANDARD PRACTICE SP-61
This MSS Standard Practice was developed under the consensus of MSS Technical Committees 114, Steel Valves,
and the MSS Coordinating Committee. The content of this Standard Practice is the resulting efforts of
knowledgeable and experienced industry volunteers to provide an effective, clear, and non-exclusive standard that
will benefit the industry as a whole. This MSS Standard Practice describes minimal requirements and is intended
as a basis for common practice by the manufacturer, the user, and the industry at large. It is the responsibility of the
user of this Standard Practice to establish appropriate safety and health practices and determine the applicability of
regulatory requirements prior to use. The existence of an MSS Standard Practice does not in itself preclude the
manufacture, sale, or use of products not conforming to the Standard Practice. Mandatory conformance to this
Standard Practice is established only by reference in other documents such as a code, specification, sales contract,
or public law, as applicable. MSS has no power, nor does it undertake, to enforce or certify compliance with this
document. Any certification or other statement of compliance with the requirements of this Standard Practice shall
not be attributable to MSS and is solely the responsibility of the certifier or maker of the statement.
"Unless otherwise specifically noted in this MSS Standard Practice, other standards documents
referred to herein are identified by the date of issue that was applicable to this Standard
Practice at the date of issue of this Standard Practice (see Annex A). This Standard Practice
shall remain silent on the applicability of those other standards of prior or subsequent dates of
issue even though applicable provisions may not have changed.”
By publication of this Standard Practice, no position is taken with respect to the validity of any potential claim(s)
or of any patent rights in connection therewith. MSS shall not be held responsible for identifying any patent
rights. Users are expressly advised that determination of patent rights and the risk of infringement of such rights
are entirely their responsibility.
For all MSS Standard Practices, the term “shall” means “must” and “shall not” means “must not”.
In this Standard Practice, all text, notes, annexes, tables, figures, and references are construed to be “normative”
and essential to understand the standard’s message. All appendices and footnotes, or any other information
denoted as “supplemental”, that may be included within this Standard Practice, DO NOT involve mandatory or
normative requirements.
The U.S. customary units and SI (metric) units in this Standard Practice are regarded separately as the standard;
each should be used independently of the other. Combining or converting values between the two systems may
result in non-conformance with this Standard Practice.
Substantive changes in this 2019 edition are "flagged" by parallel bars as shown on the
margins of this paragraph. The specific detail of the change may be determined by
comparing the material flagged with that in the previous 2013 edition.
Non-toleranced dimensions in the Standard Practice are nominal unless otherwise specified.
Excerpts of this Standard Practice may be quoted with written permission. Credit lines should read
‘Extracted from MSS SP-61-2019 with permission of the publisher, Manufacturers Standardization
Society of the Valve and Fittings Industry'. Reproduction and/or electronic transmission or dissemination
is prohibited under copyright convention unless written permission is granted by the Manufacturers
Standardization Society of the Valve and Fittings Industry Inc. All rights reserved.
MSS is a registered trademark of the Manufacturers Standardization Society of the Valve and Fittings Industry, Inc.
Copyright ©, 2019 by
Manufacturers Standardization Society
of the
Valve and Fittings Industry, Inc.
Printed in U.S.A.
i
MSS STANDARD PRACTICE SP-61
FOREWORD
This Standard Practice for Pressure Testing of Valves was originally adopted in 1961. It was developed
for the purpose of providing a uniform means of testing valves commonly used in the "full open" and "full
closed" type of service. For control valves, refer to standards ISA-75.19.01 and FCI 70-2, which may be
more appropriate for control valve pressure testing.
With the identification of General Purpose, Special Service, and Severe Service Valves, an MSS Standard
Practice has been recently introduced for supplementary high-pressure testing; namely, “Supplemental HP
Gas Test Procedures for Valves”. MSS SP-61 continues to be offered as a means of testing for all valves,
regardless of criticality.
ii
MSS STANDARD PRACTICE SP-61
iii
MSS STANDARD PRACTICE SP-61
TABLE OF CONTENTS
SECTION
1 SCOPE ........................................................................................................................................ 1
2 DEFINITIONS ............................................................................................................................ 1
3 GENERAL REQUIREMENTS .................................................................................................. 1
4 SHELL LEAKAGE TESTS ........................................................................................................ 2
5 SEAT CLOSURE TESTS ........................................................................................................... 3
TABLE
1 Shell Leakage Test Duration ....................................................................................................... 2
2 Alternate Gas Test ...................................................................................................................... 3
3 Seat Closure Test Duration ......................................................................................................... 5
4 Units of Leakage per NPS/DN .................................................................................................... 5
ANNEX
A Referenced Standards and Applicable Dates ........................................................................... 6
iv
hhhhh
hhhhh
hhhhh
hhhhh
hhhhh
hhhhh
hhhhh
hhhhh
Purchase or View a Full Listing of MSS Standards at:
http://msshq.org/Store/PriceList.cfm
About MSS
The Manufacturers Standardization Society (MSS) of the Valve and Fittings Industry is a non-profit technical association organized
for development and improvement of industry, national and international codes and standards for Valves, Valve Actuators, Valve
Modifications, Pipe Fittings, Flanges, Pipe Hangers and Supports, and Associated Seals. Since its establishment in 1924, MSS has
been dedicated to developing standards for national and global applications, in cooperation with other standardizing bodies and
regulatory authorities. MSS is an American National Standards Institute (ANSI)-accredited standards developer.
MSS SP-61-2019