Professional Documents
Culture Documents
ZL-7918A Humidity and Temperature Controller
ZL-7918A Humidity and Temperature Controller
Feature
ZL-7918A is an intelligent temperature and humidity controller, safe and stable, convenient to operate, applicable for control
of incubator, climate chamber, warehouse, and so on.
Specification
◇ Power supply: 100 ~ 240Vac, 50/60Hz.
◇ One temperature sensor (L = 2.0 meter), one humidity sensor (L = 2.0 meter).
◇ Setting range: Humidity 10 ~ 80% RH. Temperature 1 ~ 65℃
◇ Display range: Humidity 0 ~ 99% RH. Temperature -9.9 ~ 99℃.
◇ Measuring accuracy: Humidity ±3%@25℃. Temperature ±1%@25℃.
◇ Output control: 7 outputs (main-heater, aux-heater, lamp, humidity, egg-right-turning, egg-left-turning, fan).
◇ Output load: heater ≤ 1500W. Lamp ≤ 100W. Humidity, egg-turning and fan ≤ 1A/250Vac
◇ Hatched day counter: the maximum value is 99 days.
◇ Egg turn control: Turn period: 1 ~ 999 minutes. Turn driving time: 0 ~ 999 seconds. Turn times counter: 0 ~ 999 times.
◇ Air exhaustion control: Period: 1 ~ 999 minutes. Exhausting time: 0 ~ 999 seconds.
◇ Lamp control: Period: 1 ~ 999 minutes. Illuminating time: 0 ~ 999 seconds.
◇ Operation environment: -10 ~ 45℃, less than 90% RH without dew.
◇ Device dimension: 160 * 80 * 95 mm.
◇ Installation drilling size: 151.5 * 76.5 mm.
Version Information
When power supplied, the display shows the model
“791 8A”, and version “A3.1”.
Illumination operation
Manual on/off: Press【Lamp - I/O】, lamp turns on or off.
Timer on/off: For every〖Illumination period, F8〗, lamp will be on for〖Illumination time, F9〗.
Temperature control
Main heater: When room temperature ≤〖Main temperature low limit, P4〗, the main heater will be on.
When room temperature ≥〖Main temperature up limit, P3〗, the main heater will be off.
Aux. heater: When room temperature ≤〖Aux temperature low limit, P6〗, the aux. heater will be on.
When room temperature ≥〖Aux temperature up limit, P5〗, the aux. heater will be off.
Fan: When room temperature ≥〖Exhaustion temperature up limit, P1〗, the fan will be on.
When room temperature ≤〖Exhaustion temperature low limit, P2〗, the fan will be off.
Humidity control
Humidifier: When room humidity ≤〖Humidity low limit, Pb〗, humidity output will be on.
When room humidity ≥〖Humidity up limit, P9〗, humidity output will be off.
Fan: When PE = 1, when room humidity ≥〖Exhaustion humidity up limit, Pc〗, the fan will be on.
When room humidity ≤〖Exhaustion humidity low limit, Pd〗, the fan will be off.
When PE = 0, no protecting exhaustion when over wet.
When egg-turned-counter reaches〖Egg turn times, F3〗, there will be no egg turn, and LED “UP” and “DOWN” will
be blinking.
Fast check the egg-turned-counter: see paragraph at page 2: Check Incubated Days and Egg Turned Counter
Attention: When power supplied, or when controller offline, the egg-turned-counter will be reset to zero.
Alarm control
When room temperature ≥〖High temperature warning point, P0〗, buzzer alarms, room temperature display blinks.
When room temperature ≤〖Low temperature warning point, P7〗, buzzer alarms, room temperature display blinks.
When room humidity ≥〖High humidity warning point, P8〗, buzzer alarms, room humidity display blinks.
When room humidity ≤〖Low humidity warning point, PP〗, buzzer alarms, room humidity display blinks.
The buzzer alarming can be stopped and restored by pressing【Enter】key.
Incubated days
〖Incubated days, FF〗records the incubated days.
Fast check〖Incubated days, FF〗: see paragraph at page 2: Check Incubated Days and Egg Turned Counter
〖Incubated days, FF〗is saved even after power supply loses, and it is not cleared after system On/Off.
To make use of the data, it is necessary to clear the record before starting a new batch incubation.
When it reaches to 99, it will not increase any more, and will stay at 99.
LED indication
LED On Blinking Off
Fan on during〖Air
FAN Fan on, because of temperature and humidity protection exhaustion. Fan off
exhausting time, F5〗
HEAT1 Main heater on Main heater off
HEAT2 Aux. heater on Aux. heater off
UP Egg left turning now Egg-turned-counter has reached〖Egg turn times, F3〗 No left turning
DOWN Egg right turning now Egg-turned-counter has reached〖Egg turn times, F3〗 No right turning
WET Humidifying output on Humidifying output off
ALARM Room temperature or humidity is over warning points, or sensor fails
Warning code
Code Indication
E1 Temperature sensor failure
E2 Humidity sensor failure
E3 Room temperature is higher than〖High temperature warning point, P0〗
E4 Room temperature is lower than 〖Low temperature warning point, P7〗
E5 Room humidity is higher than〖High humidity warning point, P8〗
E6 Room humidity is lower than〖Low humidity warning point, PP〗
Wiring Diagram
Attention
The device is shipped with factory
default setting. It suits for normal
hatching requirements. It is even
able to use directly without any
setting for other parameters. About
factory default setting, see the tables
above.
Humidity sensor will not work correctly when covered with dust, water or dew. Please keep it clean and dry.
The sensor is suitable to working within 20% to 80%RH.
Before clean sensor, be sure there is no static electricity in hands!
Manufacturer is responsible for the device itself, is not responsible to losses resulted by the failure of this device.