CALCULATION SHEET

JOB / Contract No. : JOB - 269

Project : Luffing Cylinder Structural Lifting Analysis

Document Title : LOCAL CHECK BEAM DECK DUE TO LIFTING OF LUFFING CYLINDER

Document No. : RB-SYN-10421190873-XXXX

Revision : Issued for Review
LQ Module Roof Deck Primary Beam - Lifting Point A1
1. DATA & ASSUMPTION
This spreadsheet calculates the adequacy of the existing supporting beam due to lifting activity in Ruby PQP.
Assumptions : 1. Local check only considered for the existing beam at the PQP topside.
2. The additional data have been given by COMPANY as present in Appendix A.

2. MEMBER PROPERTIES
Section Properties UB 533x210x82 Stiffness Properties
Overall Depth h = 528.3 mm Elasticity Modulus E = ####### MPa
Section Width b = 208.8 mm Shear Modulus G = 80000 MPa
Web Thickness tw = 9.6 mm Yield Strength Fy = 345 MPa
Flange Thickness tf = 13.2 mm Member Compactness = SLENDER
Section Area A = 10500.0 mm2
Section Modulus Sy = 1.8.E+06 mm3 Unbraced Length Lb = 3500 mm
Sz = 1.9.E+05 mm3 Clear Beam Span Lc = 3500 mm
2
Shear Area Av = 4818.2 mm
Radius of Gyration ry = 213.0 mm Slenderness Ratio kL/ry = 16.43
rz = 43.8 mm kL/rz = 79.91
Member Span L = 3500 mm Slenderness Cc = 60.35
Const. (AISC )

Page 1 of 12
 CALCULATION SHEET

JOB / Contract No. : JOB - 269

Project : Luffing Cylinder Structural Lifting Analysis

Document Title : LOCAL CHECK BEAM DECK DUE TO LIFTING OF LUFFING CYLINDER

Document No. : RB-SYN-10421190873-XXXX

Revision : Issued for Review

3. ADDITIONAL LOADINGS
Add. Loadings Point A Point B Point C
Case
P (kN) Vz (kN) Vz (kN) M (kN.m) Vz (kN) M (kN.m)
CANTILEVER 35.01 -35.01 -35.01 70.02 35.01 122.53
Maximum Internal Force -35.01 -35.01 70.02 35.01 122.53

4. MEMBER ACTUAL STRESS

Point A (Cantilever)
Axial Stress fa = PA / A = 3.33 MPa
Bending Stress fb = MA / Sy = 0.00 MPa
Shear Stress fv = VzA / Av = 7.27 MPa
Point B (Mid Span)
Axial Stress fa = PB/ A = 0.00 MPa
Bending Stress fb = MB / Sy = 38.90 MPa
Shear Stress fv = VzB / Av = 7.27 MPa
Point C (Pinned)
Axial Stress fa = PC / A = 0.00 MPa
Bending Stress fb = MC / Sy = 68.07 MPa
Shear Stress fv = VzC / Av = -7.27 MPa

5. STRESS RATIO
ACTUAL ALLOWABLE
LOCATION STRESS RATIO REMARKS
(MPa) (MPa)
SHEAR 7.27 138.00 0.05 < 1.0 , OK
A
AXIAL 3.33 160.17 0.02 < 1.0 , OK
BENDING 38.90 204.92 0.19 < 1.0 , OK
B
SHEAR 7.27 138.00 0.05 < 1.0 , OK
SHEAR -7.27 138.00 0.05 < 1.0 , OK
C
BENDING 68.07 227.70 0.30 < 1.0 , OK
Max. UC 0.30 < 1.0 , OK

6. FLANGE BENDING LOCAL CHECK

A pair of stiffeners shall be provided opposite the tension flange or flange plate of the beam or girder framing
into the member if : (AISC-ASD 9th edition Section K1-1)
tf < 0.4* √ ( Pbf /Fyc) => 13.20 > 0.165

where Pbf = 5/3 * Pmax = 58.35 kN

tf = Flange Thk. = 13.20 mm
∴ No Tension Flange is required

Page 2 of 12
 CALCULATION SHEET

JOB / Contract No. : JOB - 269

Project : Luffing Cylinder Structural Lifting Analysis

Document Title : LOCAL CHECK BEAM DECK DUE TO LIFTING OF LUFFING CYLINDER

Document No. : RB-SYN-10421190873-XXXX

Revision : Issued for Review
7. LOCAL WEB YIELDING
Bearing stiffeners shall be provided if the compressive stress at the web toe of the fillet resulting from concen-
trated load (as shown in following eq.) exceeds 0.66 Fy (AISC-ASD 9th edition Section K1-3)

R > 0.66 Fy => 0.75 < 227.7

tw ( N + 2.50k)

where R = Vmax = 35.01 kN

tw = Web Thickness = 9.6 mm
N = Bearing Length = 3500.0 mm
k = Dist. From outer face of = 25.9 mm
flange to web toe
∴ No Bearing Stiffener is required

9. LOCAL WEB CRIPPLING

Bearing stiffeners shall be provided in the webs of members, when the compressive force applied at a distance
more than d/2, exceeds the following limits : `

⎡ 1.5
⎤
⎛ N ⎞⎛ t ⎞
67.5t w ⎢1 + 3⎜ ⎟⎜ w ⎟ ⎥ Fyw t f / t w
2
Pmax < => 35.01 < 4741.27
⎢ ⎝ d ⎠⎜⎝ t f ⎟
⎠ ⎥
⎣ ⎦

where tw = Web Thickness = 9.60 mm

tf = Flange Thickness = 13.20 mm
d = Depth of member = 528.30 mm
N = Bearing length = 3.50 m
= 3500.00 mm
∴ No Bearing Stiffener is required

10. COMPRESSION BUCKLING OF THE WEB

A stiffener or a pair of stiffeners shall be provided opposite the compression flange when the web depth clear of
fillets dc is greater than : (AISC-ASD 9th edition Section K1-8)
3
dc > 4100 t wc f y => 476.5 < 3032.0
Pbf
where Pbf = 5/3 * Pmax = 58.35 kN
tw = Web Thickness = 9.60 mm
∴ No Stiffener is required

Page 3 of 12
 CALCULATION SHEET

JOB / Contract No. : JOB - 269

Project : Luffing Cylinder Structural Lifting Analysis

Document Title : LOCAL CHECK BEAM DECK DUE TO LIFTING OF LUFFING CYLINDER

Document No. : RB-SYN-10421190873-XXXX

Revision : Issued for Review
LQ Module Roof Deck SecondaryBeam - Lifting Point A2
1. DATA & ASSUMPTION
This spreadsheet calculates the adequacy of the existing supporting beam due to lifting activity in Ruby PQP.
Assumptions : 1. Local check only considered for the existing beam at the PQP topside.
2. The additional data have been given by COMPANY as present in Appendix A.

2. MEMBER PROPERTIES
Section Properties UB 203x133x25 Stiffness Properties
Overall Depth h = 203.2 mm Elasticity Modulus E = ####### MPa
Section Width b = 133.2 mm Shear Modulus G = 80000 MPa
Web Thickness tw = 5.7 mm Yield Strength Fy = 345 MPa
Flange Thickness tf = 7.8 mm Member Compactness = SLENDER
Section Area A = 3200.0 mm2
Section Modulus Sy = 2.3.E+05 mm3 Unbraced Length Lb = 1000 mm
Sz = 4.6.E+04 mm3 Clear Beam Span Lc = 1000 mm
2
Shear Area Av = 1069.3 mm
Radius of Gyration ry = 85.6 mm Slenderness Ratio kL/ry = 11.68
rz = 31.0 mm kL/rz = 32.26
Member Span L = 1000 mm Slenderness Cc = 60.35
Const. (AISC )

Page 4 of 12
 CALCULATION SHEET

JOB / Contract No. : JOB - 269

Project : Luffing Cylinder Structural Lifting Analysis

Document Title : LOCAL CHECK BEAM DECK DUE TO LIFTING OF LUFFING CYLINDER

Document No. : RB-SYN-10421190873-XXXX

Revision : Issued for Review

3. ADDITIONAL LOADINGS
Add. Loadings Point A Point B Point C
Case
P (kN) Vz (kN) Vz (kN) M (kN.m) Vz (kN) M (kN.m)
CANTILEVER 35.01 -35.01 -35.01 17.50 35.01 35.01
Maximum Internal Force -35.01 -35.01 17.50 35.01 35.01

4. MEMBER ACTUAL STRESS

Point A (Cantilever)
Axial Stress fa = PA / A = 10.94 MPa
Bending Stress fb = MA / Sy = 0.00 MPa
Shear Stress fv = VzA / Av = 32.74 MPa
Point B (Mid Span)
Axial Stress fa = PB/ A = 0.00 MPa
Bending Stress fb = MB / Sy = 76.11 MPa
Shear Stress fv = VzB / Av = 32.74 MPa
Point C (Pinned)
Axial Stress fa = PC / A = 0.00 MPa
Bending Stress fb = MC / Sy = 152.22 MPa
Shear Stress fv = VzC / Av = -32.74 MPa

5. STRESS RATIO
ACTUAL ALLOWABLE
LOCATION STRESS RATIO REMARKS
(MPa) (MPa)
SHEAR 32.74 138.00 0.24 < 1.0 , OK
A
AXIAL 10.94 185.37 0.06 < 1.0 , OK
BENDING 76.11 227.70 0.33 < 1.0 , OK
B
SHEAR 32.74 138.00 0.24 < 1.0 , OK
SHEAR -32.74 138.00 0.24 < 1.0 , OK
C
BENDING 152.22 227.70 0.67 < 1.0 , OK
Max. UC 0.67 < 1.0 , OK

6. FLANGE BENDING LOCAL CHECK

A pair of stiffeners shall be provided opposite the tension flange or flange plate of the beam or girder framing
into the member if : (AISC-ASD 9th edition Section K1-1)
tf < 0.4* √ ( Pbf /Fyc) => 7.80 > 0.165

where Pbf = 5/3 * Pmax = 58.35 kN

tf = Flange Thk. = 7.80 mm
∴ No Tension Flange is required

Page 5 of 12
 CALCULATION SHEET

JOB / Contract No. : JOB - 269

Project : Luffing Cylinder Structural Lifting Analysis

Document Title : LOCAL CHECK BEAM DECK DUE TO LIFTING OF LUFFING CYLINDER

Document No. : RB-SYN-10421190873-XXXX

Revision : Issued for Review
7. LOCAL WEB YIELDING
Bearing stiffeners shall be provided if the compressive stress at the web toe of the fillet resulting from concen-
trated load (as shown in following eq.) exceeds 0.66 Fy (AISC-ASD 9th edition Section K1-3)

R > 0.66 Fy => 1.43 < 227.7

tw ( N + 2.50k)

where R = Vmax = 35.01 kN

tw = Web Thickness = 5.7 mm
N = Bearing Length = 3500.0 mm
k = Dist. From outer face of = 15.4 mm
flange to web toe
∴ No Bearing Stiffener is required

9. LOCAL WEB CRIPPLING

Bearing stiffeners shall be provided in the webs of members, when the compressive force applied at a distance
more than d/2, exceeds the following limits : `

⎡ 1.5
⎤
⎛ N ⎞⎛ t ⎞
67.5t w ⎢1 + 3⎜ ⎟⎜ w ⎟ ⎥ Fyw t f / t w
2
Pmax < => 35.01 < 4164.05
⎢ ⎝ d ⎠⎜⎝ t f ⎟
⎠ ⎥
⎣ ⎦

where tw = Web Thickness = 5.70 mm

tf = Flange Thickness = 7.80 mm
d = Depth of member = 203.20 mm
N = Bearing length = 3.50 m
= 3500.00 mm
∴ No Bearing Stiffener is required

10. COMPRESSION BUCKLING OF THE WEB

A stiffener or a pair of stiffeners shall be provided opposite the compression flange when the web depth clear of
fillets dc is greater than : (AISC-ASD 9th edition Section K1-8)
3
dc > 4100 t wc f y => 172.4 < 634.7
Pbf
where Pbf = 5/3 * Pmax = 58.35 kN
tw = Web Thickness = 5.70 mm
∴ No Stiffener is required

Page 6 of 12
 CALCULATION SHEET

JOB / Contract No. : JOB - 269

Project : Luffing Cylinder Structural Lifting Analysis

Document Title : LOCAL CHECK BEAM DECK DUE TO LIFTING OF LUFFING CYLINDER

Document No. : RB-SYN-10421190873-XXXX

Revision : Issued for Review
LQ Module 3rd Deck Primary Beam - Lifting Point A3
1. DATA & ASSUMPTION
This spreadsheet calculates the adequacy of the existing supporting beam due to lifting activity in Ruby PQP.
Assumptions : 1. Local check only considered for the existing beam at the PQP topside.
2. The additional data have been given by COMPANY as present in Appendix A.

2. MEMBER PROPERTIES
Section Properties UB 533x210x82 Stiffness Properties
Overall Depth h = 528.3 mm Elasticity Modulus E = ####### MPa
Section Width b = 208.8 mm Shear Modulus G = 80000 MPa
Web Thickness tw = 9.6 mm Yield Strength Fy = 345 MPa
Flange Thickness tf = 13.2 mm Member Compactness = SLENDER
Section Area A = 10500.0 mm2
Section Modulus Sy = 1.8.E+06 mm3 Unbraced Length Lb = 3500 mm
Sz = 1.9.E+05 mm3 Clear Beam Span Lc = 3500 mm
2
Shear Area Av = 4818.2 mm
Radius of Gyration ry = 213.0 mm Slenderness Ratio kL/ry = 16.43
rz = 43.8 mm kL/rz = 79.91
Member Span L = 3500 mm Slenderness Cc = 60.35
Const. (AISC )

Page 7 of 12
 CALCULATION SHEET

JOB / Contract No. : JOB - 269

Project : Luffing Cylinder Structural Lifting Analysis

Document Title : LOCAL CHECK BEAM DECK DUE TO LIFTING OF LUFFING CYLINDER

Document No. : RB-SYN-10421190873-XXXX

Revision : Issued for Review

3. ADDITIONAL LOADINGS
Add. Loadings Point A Point B Point C
Case
P (kN) Vz (kN) Vz (kN) M (kN.m) Vz (kN) M (kN.m)
CANTILEVER 35.01 -35.01 -35.01 70.02 35.01 122.53
Maximum Internal Force -35.01 -35.01 70.02 35.01 122.53

4. MEMBER ACTUAL STRESS

Point A (Cantilever)
Axial Stress fa = PA / A = 3.33 MPa
Bending Stress fb = MA / Sy = 0.00 MPa
Shear Stress fv = VzA / Av = 7.27 MPa
Point B (Mid Span)
Axial Stress fa = PB/ A = 0.00 MPa
Bending Stress fb = MB / Sy = 38.90 MPa
Shear Stress fv = VzB / Av = 7.27 MPa
Point C (Pinned)
Axial Stress fa = PC / A = 0.00 MPa
Bending Stress fb = MC / Sy = 68.07 MPa
Shear Stress fv = VzC / Av = -7.27 MPa

5. STRESS RATIO
ACTUAL ALLOWABLE
LOCATION STRESS RATIO REMARKS
(MPa) (MPa)
SHEAR 7.27 138.00 0.05 < 1.0 , OK
A
AXIAL 3.33 160.17 0.02 < 1.0 , OK
BENDING 38.90 204.92 0.19 < 1.0 , OK
B
SHEAR 7.27 138.00 0.05 < 1.0 , OK
SHEAR -7.27 138.00 0.05 < 1.0 , OK
C
BENDING 68.07 227.70 0.30 < 1.0 , OK
Max. UC 0.30 < 1.0 , OK

6. FLANGE BENDING LOCAL CHECK

A pair of stiffeners shall be provided opposite the tension flange or flange plate of the beam or girder framing
into the member if : (AISC-ASD 9th edition Section K1-1)
tf < 0.4* √ ( Pbf /Fyc) => 13.20 > 0.165

where Pbf = 5/3 * Pmax = 58.35 kN

tf = Flange Thk. = 13.20 mm
∴ No Tension Flange is required

Page 8 of 12
 CALCULATION SHEET

JOB / Contract No. : JOB - 269

Project : Luffing Cylinder Structural Lifting Analysis

Document Title : LOCAL CHECK BEAM DECK DUE TO LIFTING OF LUFFING CYLINDER

Document No. : RB-SYN-10421190873-XXXX

Revision : Issued for Review
7. LOCAL WEB YIELDING
Bearing stiffeners shall be provided if the compressive stress at the web toe of the fillet resulting from concen-
trated load (as shown in following eq.) exceeds 0.66 Fy (AISC-ASD 9th edition Section K1-3)

R > 0.66 Fy => 0.75 < 227.7

tw ( N + 2.50k)

where R = Vmax = 35.01 kN

tw = Web Thickness = 9.6 mm
N = Bearing Length = 3500.0 mm
k = Dist. From outer face of = 25.9 mm
flange to web toe
∴ No Bearing Stiffener is required

9. LOCAL WEB CRIPPLING

Bearing stiffeners shall be provided in the webs of members, when the compressive force applied at a distance
more than d/2, exceeds the following limits : `

⎡ 1.5
⎤
⎛ N ⎞⎛ t ⎞
67.5t w ⎢1 + 3⎜ ⎟⎜ w ⎟ ⎥ Fyw t f / t w
2
Pmax < => 35.01 < 4741.27
⎢ ⎝ d ⎠⎜⎝ t f ⎟
⎠ ⎥
⎣ ⎦

where tw = Web Thickness = 9.60 mm

tf = Flange Thickness = 13.20 mm
d = Depth of member = 528.30 mm
N = Bearing length = 3.50 m
= 3500.00 mm
∴ No Bearing Stiffener is required

10. COMPRESSION BUCKLING OF THE WEB

A stiffener or a pair of stiffeners shall be provided opposite the compression flange when the web depth clear of
fillets dc is greater than : (AISC-ASD 9th edition Section K1-8)
3
dc > < 4100 t wc f y => 476.5 < 3032.0
Pbf
where Pbf = 5/3 * Pmax = 58.35 kN
tw = Web Thickness = 9.60 mm
∴ No Stiffener is required

Page 9 of 12
 CALCULATION SHEET

JOB / Contract No. : JOB - 269

Project : Luffing Cylinder Structural Lifting Analysis

Document Title : LOCAL CHECK BEAM DECK DUE TO LIFTING OF LUFFING CYLINDER

Document No. : RB-SYN-10421190873-XXXX

Revision : Issued for Review
P2 Module Top Deck Primary Beam - Lifting Point D
1. DATA & ASSUMPTION
This spreadsheet calculates the adequacy of the existing supporting beam due to lifting activity in Ruby PQP.
Assumptions : 1. Local check only considered for the existing beam at the PQP topside.
2. The additional data have been given by COMPANY as present in Appendix A.

2. MEMBER PROPERTIES
Section Properties UB 762x267x147 Stiffness Properties
Overall Depth h = 754.0 mm Elasticity Modulus E = ####### MPa
Section Width b = 265.2 mm Shear Modulus G = 80000 MPa
Web Thickness tw = 12.8 mm Yield Strength Fy = 345 MPa
Flange Thickness tf = 17.5 mm Member Compactness = SLENDER
Section Area A = 18700.0 mm2
Section Modulus Sy = 4.5.E+06 mm3 Unbraced Length Lb = 7000 mm
Sz = 4.1.E+05 mm3 Clear Beam Span Lc = 7000 mm
2
Shear Area Av = 9203.2 mm
Radius of Gyration ry = 300.0 mm Slenderness Ratio kL/ry = 23.33
rz = 54.0 mm kL/rz = 129.63
Member Span L = 7000 mm Slenderness Cc = 60.35
Const. (AISC )

Page 10 of 12
 CALCULATION SHEET

JOB / Contract No. : JOB - 269

Project : Luffing Cylinder Structural Lifting Analysis

Document Title : LOCAL CHECK BEAM DECK DUE TO LIFTING OF LUFFING CYLINDER

Document No. : RB-SYN-10421190873-XXXX

Revision : Issued for Review

3. ADDITIONAL LOADINGS
Add. Loadings Point A Point B Point C
Case
P (kN) Vz (kN) Vz (kN) M (kN.m) Vz (kN) M (kN.m)
SIMPLE BEAM 35.01 17.50 17.50 61.27 -17.50 0.00
Maximum Internal Force 17.50 17.50 61.27 -17.50 0.00

4. MEMBER ACTUAL STRESS

Point A (Pinned)
Axial Stress fa = PA / A = 0.00 MPa
Bending Stress fb = MA / Sy = 0.00 MPa
Shear Stress fv = VzA / Av = -1.90 MPa
Point B (Mid Span)
Axial Stress fa = PB/ A = 1.87 MPa
Bending Stress fb = MB / Sy = 13.71 MPa
Shear Stress fv = VzB / Av = -1.90 MPa
Point C (Pinned)
Axial Stress fa = PC / A = 0.00 MPa
Bending Stress fb = MC / Sy = 0.00 MPa
Shear Stress fv = VzC / Av = 1.90 MPa

5. STRESS RATIO
ACTUAL ALLOWABLE
LOCATION STRESS RATIO REMARKS
(MPa) (MPa)
A SHEAR -1.90 138.00 0.01 < 1.0 , OK
AXIAL 1.87 171.49 0.01 < 1.0 , OK
B BENDING 13.71 227.70 0.06 < 1.0 , OK
SHEAR -1.90 138.00 0.01 < 1.0 , OK
SHEAR 1.90 138.00 0.01 < 1.0 , OK
C
BENDING 0.00 227.70 0.00 < 1.0 , OK
Max. UC 0.06 < 1.0 , OK

6. FLANGE BENDING LOCAL CHECK

A pair of stiffeners shall be provided opposite the tension flange or flange plate of the beam or girder framing
into the member if : (AISC-ASD 9th edition Section K1-1)
tf < 0.4* √ ( Pbf /Fyc) => 17.50 > 0.165

where Pbf = 5/3 * Pmax = 58.35 kN

tf = Flange Thk. = 17.50 mm
∴ No Tension Flange is required

Page 11 of 12
 CALCULATION SHEET

JOB / Contract No. : JOB - 269

Project : Luffing Cylinder Structural Lifting Analysis

Document Title : LOCAL CHECK BEAM DECK DUE TO LIFTING OF LUFFING CYLINDER

Document No. : RB-SYN-10421190873-XXXX

Revision : Issued for Review
7. LOCAL WEB YIELDING
Bearing stiffeners shall be provided if the compressive stress at the web toe of the fillet resulting from concen-
trated load (as shown in following eq.) exceeds 0.66 Fy (AISC-ASD 9th edition Section K1-3)

R > 0.66 Fy => 0.26 < 227.7

tw ( N + 2.50k)

where R = Vmax = 17.50 kN

tw = Web Thickness = 12.8 mm
N = Bearing Length = 3500.0 mm
k = Dist. From outer face of = 34.0 mm
flange to web toe
∴ No Bearing Stiffener is required

9. LOCAL WEB CRIPPLING

Bearing stiffeners shall be provided in the webs of members, when the compressive force applied at a distance
more than d/2, exceeds the following limits : `

⎡ 1.5
⎤
⎛ N ⎞⎛ t ⎞
67.5t w ⎢1 + 3⎜ ⎟⎜ w ⎟ ⎥ Fyw t f / t w
2
Pmax < => 35.01 < 6124.58
⎢ ⎝ d ⎠⎜⎝ t f ⎟
⎠ ⎥
⎣ ⎦

where tw = Web Thickness = 12.80 mm

tf = Flange Thickness = 17.50 mm
d = Depth of member = 754.00 mm
N = Bearing length = 3.50 m
= 3500.00 mm
∴ No Bearing Stiffener is required

10. COMPRESSION BUCKLING OF THE WEB

A stiffener or a pair of stiffeners shall be provided opposite the compression flange when the web depth clear of
fillets dc is greater than : (AISC-ASD 9th edition Section K1-8)
3
dc > 4100 t wc f y => 686 < 7186.9
Pbf
where Pbf = 5/3 * Pmax = 58.35 kN
tw = Web Thickness = 12.80 mm
∴ No Stiffener is required

Page 12 of 12