1MRK505388-UEN C en Application Manual Busbar Protection REB650 Version 2.2
1MRK505388-UEN C en Application Manual Busbar Protection REB650 Version 2.2
The software and hardware described in this document is furnished under a license and may
be used or disclosed only in accordance with the terms of such license.
This product includes software developed by the OpenSSL Project for use in the OpenSSL
Toolkit. (http://www.openssl.org/) This product includes cryptographic software written/
developed by: Eric Young ([email protected]) and Tim Hudson ([email protected]).
Trademarks
ABB and Relion are registered trademarks of the ABB Group. All other brand or product names
mentioned in this document may be trademarks or registered trademarks of their respective
holders.
Warranty
Please inquire about the terms of warranty from your nearest ABB representative.
Disclaimer
The data, examples and diagrams in this manual are included solely for the concept or product
description and are not to be deemed as a statement of guaranteed properties. All persons
responsible for applying the equipment addressed in this manual must satisfy themselves that
each intended application is suitable and acceptable, including that any applicable safety or
other operational requirements are complied with. In particular, any risks in applications where
a system failure and/or product failure would create a risk for harm to property or persons
(including but not limited to personal injuries or death) shall be the sole responsibility of the
person or entity applying the equipment, and those so responsible are hereby requested to
ensure that all measures are taken to exclude or mitigate such risks.
This document has been carefully checked by ABB but deviations cannot be completely ruled
out. In case any errors are detected, the reader is kindly requested to notify the manufacturer.
Other than under explicit contractual commitments, in no event shall ABB be responsible or
liable for any loss or damage resulting from the use of this manual or the application of the
equipment.
Conformity
This product complies with the directive of the Council of the European Communities on the
approximation of the laws of the Member States relating to electromagnetic compatibility
(EMC Directive 2004/108/EC) and concerning electrical equipment for use within specified
voltage limits (Low-voltage directive 2006/95/EC). This conformity is the result of tests
conducted by ABB in accordance with the product standard EN 60255-26 for the EMC directive,
and with the product standards EN 60255-1 and EN 60255-27 for the low voltage directive. The
product is designed in accordance with the international standards of the IEC 60255 series.
Table of contents
Table of contents
Section 1 Introduction...................................................................................................11
1.1 This manual.................................................................................................................................. 11
1.1.1 Presumptions for Technical Data.......................................................................................... 11
1.2 Intended audience...................................................................................................................... 11
1.3 Product documentation............................................................................................................ 12
1.3.1 Product documentation set................................................................................................... 12
1.3.2 Document revision history......................................................................................................13
1.3.3 Related documents.................................................................................................................. 13
1.4 Document symbols and conventions..................................................................................... 14
1.4.1 Symbols...................................................................................................................................... 14
1.4.2 Document conventions........................................................................................................... 15
1.5 IEC 61850 edition 1 / edition 2 mapping................................................................................15
Section 2 Application.................................................................................................... 19
2.1 General IED application............................................................................................................. 19
2.2 Main protection functions........................................................................................................20
2.3 Back-up protection functions..................................................................................................20
2.4 Control and monitoring functions.......................................................................................... 21
2.5 Communication.......................................................................................................................... 23
2.6 Basic IED functions.................................................................................................................... 25
Section 3 Configuration................................................................................................27
3.1 Description of configuration REB650.....................................................................................27
3.1.1 Introduction...............................................................................................................................27
3.1.1.1 Description of A03.............................................................................................................. 27
Section 11 Logic.............................................................................................................145
11.1 Tripping logic SMPPTRC .........................................................................................................145
11.1.1 Identification...........................................................................................................................145
11.1.2 Application...............................................................................................................................145
11.1.2.1 Three-phase tripping....................................................................................................... 145
11.1.2.2 Single- and/or three-phase tripping............................................................................ 146
11.1.2.3 Single-, two- or three-phase tripping........................................................................... 147
11.1.2.4 Lock-out..............................................................................................................................148
11.1.2.5 Example of directional data........................................................................................... 148
11.1.2.6 Blocking of the function block....................................................................................... 150
11.1.3 Setting guidelines.................................................................................................................. 150
11.2 Trip matrix logic TMAGAPC.................................................................................................... 150
11.2.1 Identification...........................................................................................................................150
11.2.2 Application...............................................................................................................................150
11.2.3 Setting guidelines...................................................................................................................151
11.3 Logic for group alarm ALMCALH........................................................................................... 151
11.3.1 Identification........................................................................................................................... 151
11.3.2 Application............................................................................................................................... 151
11.3.3 Setting guidelines...................................................................................................................151
11.4 Logic for group alarm WRNCALH...........................................................................................151
11.4.1 Identification........................................................................................................................... 151
11.4.1.1 Application..........................................................................................................................151
11.4.1.2 Setting guidelines............................................................................................................. 152
11.5 Logic for group indication INDCALH.................................................................................... 152
11.5.1 Identification........................................................................................................................... 152
11.5.1.1 Application......................................................................................................................... 152
11.5.1.2 Setting guidelines............................................................................................................. 152
11.6 Configurable logic blocks....................................................................................................... 152
11.6.1 Application...............................................................................................................................152
11.6.2 Setting guidelines.................................................................................................................. 152
11.6.2.1 Configuration.....................................................................................................................153
11.7 Fixed signal function block FXDSIGN................................................................................... 153
11.7.1 Identification........................................................................................................................... 153
11.7.2 Application...............................................................................................................................154
11.8 Boolean 16 to Integer conversion B16I................................................................................. 155
11.8.1 Identification...........................................................................................................................155
11.8.2 Application...............................................................................................................................155
11.9 Boolean to integer conversion with logical node representation, 16 bit BTIGAPC..... 156
11.9.1 Identification...........................................................................................................................156
11.9.2 Application...............................................................................................................................156
11.10 Integer to Boolean 16 conversion IB16................................................................................. 157
11.10.1 Identification........................................................................................................................... 157
11.10.2 Application............................................................................................................................... 157
11.11 Integer to Boolean 16 conversion with logic node representation ITBGAPC............... 158
11.11.1 Identification...........................................................................................................................158
11.11.2 Application...............................................................................................................................158
11.12 Elapsed time integrator with limit transgression and overflow supervision
TEIGAPC......................................................................................................................................159
11.12.1 Identification...........................................................................................................................159
11.12.2 Application...............................................................................................................................159
11.12.3 Setting guidelines.................................................................................................................. 159
11.13 Comparator for integer inputs - INTCOMP......................................................................... 160
11.13.1 Identification...........................................................................................................................160
11.13.2 Application.............................................................................................................................. 160
11.13.3 Setting guidelines.................................................................................................................. 160
11.13.4 Setting example...................................................................................................................... 161
11.14 Comparator for real inputs - REALCOMP............................................................................. 161
11.14.1 Identification........................................................................................................................... 161
11.14.2 Application............................................................................................................................... 161
11.14.3 Setting guidelines...................................................................................................................161
11.14.4 Setting example......................................................................................................................162
Section 12 Monitoring...................................................................................................165
12.1 Measurement............................................................................................................................ 165
12.1.1 Identification...........................................................................................................................165
12.1.2 Application...............................................................................................................................165
12.1.3 Zero clamping......................................................................................................................... 166
12.1.4 Setting guidelines.................................................................................................................. 167
12.1.4.1 Setting examples.............................................................................................................. 169
12.2 Gas medium supervision SSIMG............................................................................................ 173
12.2.1 Identification........................................................................................................................... 173
12.2.2 Application............................................................................................................................... 173
12.2.3 Setting guidelines.................................................................................................................. 174
12.3 Liquid medium supervision SSIML........................................................................................ 174
12.3.1 Identification........................................................................................................................... 174
12.3.2 Application...............................................................................................................................174
12.3.3 Setting guidelines...................................................................................................................175
12.4 Breaker monitoring SSCBR..................................................................................................... 175
12.4.1 Identification........................................................................................................................... 175
12.4.2 Application............................................................................................................................... 175
14.3.1 Application...............................................................................................................................196
14.3.2 Setting guidelines.................................................................................................................. 197
14.4 Routes......................................................................................................................................... 197
14.4.1 Application...............................................................................................................................197
14.4.2 Setting guidelines.................................................................................................................. 197
Section 16 Security........................................................................................................225
16.1 Authority status ATHSTAT......................................................................................................225
16.1.1 Application...............................................................................................................................225
16.2 Self supervision with internal event list INTERRSIG.......................................................... 225
16.2.1 Application...............................................................................................................................225
Section 18 Requirements..............................................................................................247
18.1 Current transformer requirements.......................................................................................247
18.1.1 Current transformer basic classification and requirements.........................................247
18.1.2 Conditions............................................................................................................................... 248
18.1.3 Fault current............................................................................................................................249
18.1.4 Secondary wire resistance and additional load...............................................................249
18.1.5 General current transformer requirements......................................................................250
18.1.6 Rated equivalent secondary e.m.f. requirements........................................................... 250
18.1.6.1 Breaker failure protection.............................................................................................. 250
18.1.6.2 Non-directional instantaneous and definitive time, phase and residual
overcurrent protection.................................................................................................... 251
18.1.6.3 Non-directional inverse time delayed phase and residual overcurrent
protection...........................................................................................................................251
18.1.7 Current transformer requirements for CTs according to other standards............... 252
18.1.7.1 Current transformers according to IEC 61869-2, class P, PR................................... 252
18.1.7.2 Current transformers according to IEC 61869-2, class PX, PXR (and old IEC
60044-6, class TPS and old British Standard, class X).............................................. 252
18.1.7.3 Current transformers according to ANSI/IEEE.......................................................... 253
18.2 Voltage transformer requirements...................................................................................... 253
18.3 SNTP server requirements......................................................................................................254
18.4 PTP requirements.....................................................................................................................254
18.5 IEC/UCA 61850-9-2LE Merging unit requirements ...........................................................254
Section 1 Introduction
1.1 This manual GUID-AB423A30-13C2-46AF-B7FE-A73BB425EB5F v19
The application manual contains application descriptions and setting guidelines sorted per
function. The manual can be used to find out when and for what purpose a typical protection
function can be used. The manual can also provide assistance for calculating settings.
The technical data stated in this document are only valid under the following circumstances:
1. Main current transformers with 1 A or 2 A secondary rating are wired to the IED 1 A rated
CT inputs.
2. Main current transformer with 5 A secondary rating are wired to the IED 5 A rated CT
inputs.
3. CT and VT ratios in the IED are set in accordance with the associated main instrument
transformers. Note that for functions which measure an analogue signal which do not
have corresponding primary quantity the 1:1 ratio shall be set for the used analogue inputs
on the IED. Example of such functions are: HZPDIF, ROTIPHIZ and STTIPHIZ.
4. Parameter IBase used by the tested function is set equal to the rated CT primary current.
5. Parameter UBase used by the tested function is set equal to the rated primary phase-to-
phase voltage.
6. Parameter SBase used by the tested function is set equal to:
• √3 × IBase × UBase
7. The rated secondary quantities have the following values:
• Rated secondary phase current Ir is either 1 A or 5 A depending on selected TRM.
• Rated secondary phase-to-phase voltage Ur is within the range from 100 V to 120 V.
• Rated secondary power for three-phase system Sr = √3 × Ur × Ir
8. For operate and reset time testing, the default setting values of the function are used if
not explicitly stated otherwise.
9. During testing, signals with rated frequency have been injected if not explicitly stated
otherwise.
This manual addresses the protection and control engineer responsible for planning, pre-
engineering and engineering.
The protection and control engineer must be experienced in electrical power engineering and
have knowledge of related technology, such as protection schemes and communication
principles.
Decommissioning
Commissioning
Maintenance
Engineering
Operation
Installing
Engineering manual
Installation manual
Commissioning manual
Operation manual
Application manual
Technical manual
Communication
protocol manual
Cyber security
deployment guideline
IEC07000220-4-en.vsd
IEC07000220 V4 EN-US
The installation manual contains instructions on how to install the IED. The manual provides
procedures for mechanical and electrical installation. The chapters are organized in the
chronological order in which the IED should be installed.
The commissioning manual contains instructions on how to commission the IED. The manual
can also be used by system engineers and maintenance personnel for assistance during the
testing phase. The manual provides procedures for the checking of external circuitry and
energizing the IED, parameter setting and configuration as well as verifying settings by
secondary injection. The manual describes the process of testing an IED in a station which is
not in service. The chapters are organized in the chronological order in which the IED should be
commissioned. The relevant procedures may be followed also during the service and
maintenance activities.
The operation manual contains instructions on how to operate the IED once it has been
commissioned. The manual provides instructions for the monitoring, controlling and setting of
the IED. The manual also describes how to identify disturbances and how to view calculated
and measured power grid data to determine the cause of a fault.
The application manual contains application descriptions and setting guidelines sorted per
function. The manual can be used to find out when and for what purpose a typical protection
function can be used. The manual can also provide assistance for calculating settings.
The technical manual contains operation principle descriptions, and lists function blocks, logic
diagrams, input and output signals, setting parameters and technical data, sorted per
function. The manual can be used as a technical reference during the engineering phase,
installation and commissioning phase, and during normal service.
The point list manual describes the outlook and properties of the data points specific to the
IED. The manual should be used in conjunction with the corresponding communication
protocol manual.
The cyber security deployment guideline describes the process for handling cyber security
when communicating with the IED. Certification, Authorization with role based access control,
and product engineering for cyber security related events are described and sorted by
function. The guideline can be used as a technical reference during the engineering phase,
installation and commissioning phase, and during normal service.
The electrical warning icon indicates the presence of a hazard which could
result in electrical shock.
The warning icon indicates the presence of a hazard which could result in
personal injury.
The caution hot surface icon indicates important information or warning about
the temperature of product surfaces.
Class 1 Laser product. Take adequate measures to protect the eyes and do not
view directly with optical instruments.
The information icon alerts the reader of important facts and conditions.
The tip icon indicates advice on, for example, how to design your project or
how to use a certain function.
Although warning hazards are related to personal injury, it is necessary to understand that
under certain operational conditions, operation of damaged equipment may result in
degraded process performance leading to personal injury or death. It is important that the
user fully complies with all warning and cautionary notices.
• Abbreviations and acronyms in this manual are spelled out in the glossary. The glossary
also contains definitions of important terms.
• Push button navigation in the LHMI menu structure is presented by using the push button
icons.
For example, to navigate between the options, use and .
• HMI menu paths are presented in bold.
For example, select Main menu/Settings.
• LHMI messages are shown in Courier font.
For example, to save the changes in non-volatile memory, select Yes and press .
• Parameter names are shown in italics.
For example, the function can be enabled and disabled with the Operation setting.
• Each function block symbol shows the available input/output signal.
• the character ^ in front of an input/output signal name indicates that the signal
name may be customized using the PCM600 software.
• the character * after an input signal name indicates that the signal must be
connected to another function block in the application configuration to achieve a
valid application configuration.
• Dimensions are provided both in inches and millimeters. If it is not specifically mentioned
then the dimension is in millimeters.
Function block names are used in ACT and PST to identify functions. Respective function block
names of Edition 1 logical nodes and Edition 2 logical nodes are shown in the table below.
Section 2 Application
2.1 General IED application
GUID-F13C1639-4853-4305-84CA-D9648B0648B0 v5
The numerical high impedance differential busbar protection REB650 IED provides its users
with a wide variety of application opportunities. Designed primarily for the protection of
single busbar with or without sectionalizers in high impedance based applications, it also
offers high impedance differential protection for generators, autotransformers, shunt
reactors and capacitor banks.
Its I/O capability allows you to protect up to three 3-phase high impedance differential
protection zones with a single IED. A number of additional protection functions are available
for the protection of the bus coupler bay. The additional protection functions include different
types of phase and earth fault overcurrent protection and over voltage/under voltage
protection.
One pre-configured package has been defined for the following application:
For the high impedance differential protection, the differential current process is made in the
analogue current transformer circuits where the differential current is connected to the IED via
a high ohmic resistor. In REB650, a current input is used for each phase and protection zone.
The package is configured and ready for direct use. Analog inputs and binary input/output
circuits are pre-defined.
The IED can be used in applications with the IEC/UCA 61850-9-2LE process bus with up to four
Merging Units (MU). Each MU has eight analogue channels, four current and four voltages.
Conventional input transformer module and Merging Unit channels can be mixed freely in your
application.
The pre-configured IED can be changed and adapted to suit specific applications with the
application configuration tool.
Forcing of binary inputs and outputs is a convenient way to test wiring in substations as well
as testing configuration logic in the IEDs. Basically it means that all binary inputs and outputs
on the IED I/O modules (BOM, BIM and IOM) can be forced to arbitrary values.
The Flexible Product Naming allows the customer to use an IED-vendor independent IEC 61850
model of the IED. This customer model will be used as the IEC 61850 data model, but all other
aspects of the IED will remain unchanged (e.g., names on the local HMI and names in the tools).
This offers significant flexibility to adapt the IED to the customers' system and standard
solution.
GUID-F5776DD1-BD04-4872-BB89-A0412B4B5CC3 v1
The following tables list all the functions available in the IED. Those functions
that are not exposed to the user or do not need to be configured are not
described in this manual.
Voltage protection
UV2PTUV 27 Two step undervoltage protection 1
OV2PTOV 59 Two step overvoltage protection 1
ROV2PTOV 59N Two step residual overvoltage protection 2
1) 67 requires voltage
2) 67N requires voltage
Section 3 Configuration
3.1 Description of configuration REB650
3.1.1 Introduction
GUID-79B8BC84-4AAB-44E7-86CD-FF63098B009D v3
The basic delivery includes one binary input module and one binary output module, which is
sufficient for the default configured I/O to trip and close circuit breaker. All IEDs can be
reconfigured with the help of the application configuration tool in PCM600. The IED can be
adapted to special applications and special logic can be developed, such as logic for automatic
opening of disconnectors and closing of ring bays, automatic load transfer from one busbar to
the other, and so on.
The basic IED configuration is provided with the signal matrix, single line diagram and the
application configuration prepared for the functions included in the product by default. All
parameters should be verified by the customer, since these are specific to the system, object
or application. Optional functions and optional I/O ordered will not be configured at delivery.
It should be noted that the standard only includes one binary input and one binary output
module and only the key functions such as tripping are connected to the outputs in the signal
matrix tool. The required total I/O must be calculated and specified at ordering.
The configurations are as far as found necessary provided with application comments to
explain why the signals have been connected in the special way. On request, ABB is available to
support the re-configuration work, either directly or to do the design checking.
Complete busbar protection for two busbar sections (zone 1 and 2), with the possibility for
check zone.
WA1 WA2
REB650 A03 – High impedance busbar
protection for up to 3 zones 12AI (9I + 3U)
DFR/SER DR
DRP RDRE
94 1→0
SMP PTRC
QA1 QA1 QA1 QB2 QA1 QA1 QA1 QA1
87 S SCBR
Id>
S SCBR
HZ PDIF
Zone 1
ZONE1_CT
94 1→0
QB1 SMP PTRC
87 S SCBR
Id>
S SCBR
HZ PDIF
Zone 2
ZONE2_CT
QA1
94 1→0
SMP PTRC
Zone 3
87 S SCBR
Id>
S SCBR (available if
HZ PDIF
ZONE3_CT needed)
IEC10000341-4-en.vsd
IEC10000341 V4 EN-US
Analog input channels must be configured and set properly in order to get correct
measurement results and correct protection operations. For power measuring, all directional
and differential functions, the directions of the input currents must be defined in order to
reflect the way the current transformers are installed/connected in the field ( primary and
secondary connections ). Measuring and protection algorithms in the IED use primary system
quantities. Setting values are in primary quantities as well and it is important to set the data
about the connected current and voltage transformers properly.
An AISVBAS reference PhaseAngleRef can be defined to facilitate service values reading. This
analog channel's phase angle will always be fixed to zero degrees and remaining analog
channel's phase angle information will be shown in relation to this analog input. During testing
and commissioning of the IED, the reference channel can be changed to facilitate testing and
service values reading.
The IED has the ability to receive analog values from primary equipment, that
are sampled by Merging units (MU) connected to a process bus, via the IEC
61850-9-2 LE protocol.
SEMOD130348-4 v5
The available setting parameters related to analog inputs are depending on the
actual hardware (TRM) and the logic configuration made in PCM600.
If a second TRM is used, at least one TRM channel must be configured to get
the service values. However, the MU physical channel must be configured to get
service values from that channel.
All phase angles are calculated in relation to a defined reference. An appropriate analog input
channel is selected and used as phase reference. The parameter PhaseAngleRef defines the
analog channel that is used as phase angle reference.
The direction of a current to the IED is depending on the connection of the CT. Unless
indicated otherwise, the main CTs are supposed to be star connected and can be connected
with the earthing point to the object or from the object. This information must be set in the
IED. The convention of the directionality is defined as follows: A positive value of current,
power, and so on means that the quantity has the direction into the object and a negative
value means direction out from the object. For directional functions the direction into the
object is defined as Forward and the direction out from the object is defined as Reverse. See
Figure 3
A positive value of current, power, and so on (forward) means that the quantity flows towards
the object. A negative value of current, power, and so on (reverse) means that the quantity
flows away from the object. See Figure 3.
en05000456.vsd
IEC05000456 V1 EN-US
Line
Ip
Transformer Ip Ip
Line
Reverse Forward
Definition of direction
for directional functions
Transformer
Is Is
protection Line protection
IED IED
IEC05000753=IEC05
000753=1=en=Origin
al[1].vsd
IEC05000753 V2 EN-US
Two IEDs used for protection of two objects and sharing a CT.
Transformer
Line
Reverse Forward
Definition of direction
for directional functions
Transformer
protection Line protection
IED IED
IEC05000460 V2 EN-US
Transformer
Line
Forward Reverse
Definition of direction
for directional
Transformer and line functions
Line protection
IED
IEC05000461 V2 EN-US
When a function is set to Reverse and shall protect an object in reverse direction, it shall be
noted that some directional functions are not symmetrical regarding the reach in forward and
reverse direction. It is in first hand the reach of the directional criteria that can differ. Normally
it is not any limitation but it is advisable to have it in mind and check if it is acceptable for the
application in question.
If the IED has sufficient number of analog current inputs, an alternative solution is shown in
Figure 7. The same currents are fed to two separate groups of inputs and the line and
transformer protection functions are configured to the different inputs. The CT direction for
the current channels to the line protection is set with the line as reference object and the
directional functions of the line protection shall be set to Forward to protect the line.
Transformer
Line
Reverse Forward
Definition of direction
for directional
Transformer and line functions
Line protection
IED
Setting of current input
for line functions:
Set parameter
CTStarPoint with
Line as
reference object.
Setting of current input Setting of current input Correct setting is
for transformer functions: for transformer functions: "FromObject"
Set parameter Set parameter
CTStarPoint with CTStarPoint with
Transformer as Transformer as
reference object. reference object.
Correct setting is Correct setting is
"ToObject" "ToObject"
IEC05000462 V2 EN-US
Figure 8:
For busbar protection, it is possible to set the CTStarPoint parameters in two ways.
The first solution will be to use busbar as a reference object. In that case for all CT inputs
marked with 1 in Figure 8, set CTStarPoint = ToObject, and for all CT inputs marked with 2 in
Figure 8, set CTStarPoint = FromObject.
The second solution will be to use all connected bays as reference objects. In that case for all
CT inputs marked with 1 in Figure 8, set CTStarPoint = FromObject, and for all CT inputs
marked with 2 in Figure 8, set CTStarPoint = ToObject.
Regardless which one of the above two options is selected, busbar differential protection will
behave correctly.
The main CT ratios must also be set. This is done by setting the two parameters CTsec and
CTprim for each current channel. For a 1000/1 A CT, the following settings shall be used:
• CTprim = 1000 (value in A)
• CTsec =1 (value in A).
4.2.2.4 Examples on how to connect, configure and set CT inputs for most
commonly used CT connections SEMOD55055-296 v7
Figure 9 defines the marking of current transformer terminals commonly used around the
world:
In the SMAI function block, you have to set if the SMAI block is measuring
current or voltage. This is done with the parameter: AnalogInputType: Current/
Voltage. The ConnectionType: phase -phase/phase-earth and GlobalBaseSel.
P1 P2
IPri
ISec (H1) (H2)
S1 (X1) S2 (X2)
x S2 (X2) x S1 (X1)
P2 P1
(H2) (H1)
a) b) c)
en06000641.vsd
IEC06000641 V1 EN-US
Where:
a) is symbol and terminal marking used in this document. Terminals marked with a square
indicates the primary and secondary winding terminals with the same (that is, positive)
polarity
b) and are equivalent symbols and terminal marking used by IEC (ANSI) standard for CTs. Note
c) that for these two cases the CT polarity marking is correct!
It shall be noted that depending on national standard and utility practices, the rated secondary
current of a CT has typically one of the following values:
• 1A
• 5A
However, in some cases, the following rated secondary currents are used as well:
• 2A
• 10A
It is recommended to:
• use 1A rated CT input into the IED in order to connect CTs with 1A and 2A
secondary rating
• use 5A rated CT input into the IED in order to connect CTs with 5A and 10A
secondary rating
Figure 10 gives an example about the wiring of a star connected two-phase CT set to the IED.
It gives an overview of the actions which are needed to make this measurement available to
the built-in protection and control functions within the IED as well.
For correct terminal designations, see the connection diagrams valid for the
delivered IED.
L1 L2 L3
IED
1 2
4
IL2
IL3
IL1
3
IL1
CT 600/5 SMAI2
Star Connected IL2 BLOCK AI3P
REVROT AI1
^GRP2L1 5 AI2
IL3 ^GRP2L2 AI3
^GRP2L3 AI4
^GRP2N AIN
IN
IEC13000002-4-en.vsdx
Protected Object
IEC13000002 V4 EN-US
Figure 10: Star connected three-phase CT set with star point towards the protected object
Where:
1) The drawing shows how to connect three individual phase currents from a star connected three-
phase CT set to the three CT inputs of the IED.
2) The current inputs are located in the TRM. It shall be noted that for all these current inputs the
following setting values shall be entered for the example shown in Figure 10.
• CTprim=600A
• CTsec=5A
• CTStarPoint=ToObject
Ratio of the first two parameters is only used inside the IED. The third parameter
(CTStarPoint=ToObject) as set in this example causes no change on the measured currents. In other
words, currents are already measured towards the protected object.
Table continues on next page
3) These three connections are the links between the three current inputs and the three input channels
of the preprocessing function block 4). Depending on the type of functions, which need this current
information, more than one preprocessing block might be connected in parallel to the same three
physical CT inputs.
4) The preprocessing block that has the task to digitally filter the connected analog inputs and
calculate:
These calculated values are then available for all built-in protection and control functions within the
IED, which are connected to this preprocessing function block. For this application most of the
preprocessing settings can be left to the default values.
If frequency tracking and compensation is required (this feature is typically required only for IEDs
installed in power plants), then the setting parameters DFTReference shall be set accordingly.
Section SMAI in this manual provides information on adaptive frequency tracking for the signal
matrix for analogue inputs (SMAI).
5) AI3P in the SMAI function block is a grouped signal which contains all the data about the phases L1,
L2, L3 and neutral quantity; in particular the data about fundamental frequency phasors, harmonic
content and positive sequence, negative and zero sequence quantities are available.
AI1, AI2, AI3, AI4 are the output signals from the SMAI function block which contain the fundamental
frequency phasors and the harmonic content of the corresponding input channels of the
preprocessing function block.
AIN is the signal which contains the fundamental frequency phasors and the harmonic content of
the neutral quantity. In this example, GRP2N is not connected so this data is calculated by the
preprocessing function block on the basis of the inputs GRPL1, GRPL2 and GRPL3. If GRP2N is
connected, the data reflects the measured value of GRP2N.
Another alternative is to have the star point of the three-phase CT set as shown in Figure 11:
L1 L2 L3
IED
IL2
IL3
IL1
2
1 4
IN 3
IL3 SMAI2
BLOCK AI3P
REVROT AI1
IL2 ^GRP2L1 5 AI2
^GRP2L2 AI3
CT 800/1 ^GRP2L3 AI4
IL1
Star Connected ^GRP2N AI N
IEC11000026 V4 EN-US
Figure 11: Star connected three-phase CT set with its star point away from the protected object
In the example, everything is done in a similar way as in the above described example (Figure
10). The only difference is the setting of the parameter CTStarPoint of the used current inputs
on the TRM (item 2 in Figure 11 and 10):
• CTprim=600A
• CTsec=5A
• CTStarPoint=FromObject
The ratio of the first two parameters is only used inside the IED. The third parameter as set in
this example will negate the measured currents in order to ensure that the currents are
measured towards the protected object within the IED.
A third alternative is to have the residual/neutral current from the three-phase CT set
connected to the IED as shown in Figure 11.
L1 L2 L3
IED
IL2
IL3
IL1
3 6
IN 1 4
SMAI2
BLOCK AI3P
REVROT AI1
IL3 ^GRP2L1 AI2
^GRP2L2 AI3
^GRP2L3 AI4
IL2 ^GRP2N AIN
CT 800/1
IL1
Star Connected
5
Protected Object
IEC06000644-4-en.vsdx
IEC06000644 V4 EN-US
Figure 12: Star connected three-phase CT set with its star point away from the protected object and
the residual/neutral current connected to the IED
Where:
1) Shows how to connect three individual phase currents from a star connected three-phase CT set to
the three CT inputs of the IED.
2) Shows how to connect residual/neutral current from the three-phase CT set to the fourth input in
the IED. It shall be noted that if this connection is not made, the IED will still calculate this current
internally by vectorial summation of the three individual phase currents.
3) Is the TRM where these current inputs are located. It shall be noted that for all these current inputs
the following setting values shall be entered.
• CTprim=800A
• CTsec=1A
• CTStarPoint=FromObject
• ConnectionType=Ph-N
The ratio of the first two parameters is only used inside the IED. The third parameter as set in this
example will have no influence on measured currents (that is, currents are already measured
towards the protected object).
Table continues on next page
4) Are three connections made in the Signal Matrix tool (SMT) and Application configuration tool
(ACT), which connects these three current inputs to the first three input channels on the
preprocessing function block 6). Depending on the type of functions, which need this current
information, more than one preprocessing block might be connected in parallel to these three CT
inputs.
5) Is a connection made in the Signal Matrix tool (SMT) and Application configuration tool (ACT), which
connects the residual/neutral current input to the fourth input channel of the preprocessing
function block 6). Note that this connection in SMT shall not be done if the residual/neutral current
is not connected to the IED.
6) Is a Preprocessing block that has the task to digitally filter the connected analog inputs and
calculate:
These calculated values are then available for all built-in protection and control functions within the
IED, which are connected to this preprocessing function block in the configuration tool. For this
application, most of the preprocessing settings can be left to the default values.
If frequency tracking and compensation is required (this feature is typically required only for IEDs
installed in the generating stations), then the setting parameters DFTReference shall be set
accordingly.
4.2.2.6 Example how to connect delta connected three-phase CT set to the IED SEMOD55055-392 v7
Figure 13 gives an example how to connect a delta connected three-phase CT set to the IED. It
gives an overview of the required actions by the user in order to make this measurement
available to the built-in protection and control functions in the IED as well.
For correct terminal designations, see the connection diagrams valid for the
delivered IED.
L1 L2 L3
IED
IL3
IL2
IL1
1 2
3 4
IL1-IL2
SMAI2
DAB Connected
REVROT AI1
in Delta
^GRP2L1 AI2
IL3-IL1 ^GRP2L2 AI3
^GRP2L3 AI4
^GRP2N AIN
IEC11000027-3-en.vsdx
Protected Object
IEC11000027 V3 EN-US
Where:
1) shows how to connect three individual phase currents from a delta connected three-phase CT set to
three CT inputs of the IED.
2) is the TRM where these current inputs are located. It shall be noted that for all these current inputs
the following setting values shall be entered.
CTprim=600A
CTsec=5A
• CTStarPoint=ToObject
• ConnectionType=Ph-Ph
3) are three connections made in Signal Matrix Tool (SMT), Application configuration tool (ACT), which
connect these three current inputs to first three input channels of the preprocessing function block
4). Depending on the type of functions which need this current information, more then one
preprocessing block might be connected in parallel to these three CT inputs.
4) is a Preprocessing block that has the task to digitally filter the connected analog inputs and
calculate:
These calculated values are then available for all built-in protection and control functions within the
IED, which are connected to this preprocessing function block. For this application most of the
preprocessing settings can be left to the default values.
If frequency tracking and compensation is required (this feature is typically required only for IEDs
installed in the generating stations) then the setting parameters DFTReference shall be set
accordingly.
Another alternative is to have the delta connected CT set as shown in figure 14:
L1 L2 L3
IED
IL3
IL2
IL1
2
1
3
IL1-IL3 SMAI2
BLOCK AI3P
DAC Connected
^GRP2L1 AI2
^GRP2L2 AI3
IL3-IL2 ^GRP2L3 AI4
^GRP2N AIN
IEC11000028-3-en.vsdx
Protected Object
IEC11000028 V3 EN-US
In this case, everything is done in a similar way as in the above described example, except that
for all used current inputs on the TRM the following setting parameters shall be entered:
CTprim=800A
CTsec=1A
• CTStarPoint=ToObject
• ConnectionType=Ph-Ph
It is important to notice the references in SMAI. As inputs at Ph-Ph are expected to be L1L2,
L2L3 respectively L3L1 we need to tilt 180º by setting ToObject.
Figure 15 gives an example how to connect the single-phase CT to the IED. It gives an overview
of the required actions by the user in order to make this measurement available to the built-in
protection and control functions within the IED as well.
For correct terminal designations, see the connection diagrams valid for the
delivered IED.
IED
Protected Object
L1 L2 L3
1 SMAI2
(+) BLOCK AI3P
REVROT AI1
INS ^GRP2L1 AI2
CT 1000/1
IEC11000029-4-en.vsdx
INP
IEC11000029 V4 EN-US
Where:
1) shows how to connect single-phase CT input in the IED.
2) is TRM where these current inputs are located. It shall be noted that for all these current inputs
the following setting values shall be entered.
For connection (a) shown in Fgure 15:
CTprim= 1000 A
CTsec= 1A
CTStarPoint=ToObject
Note that for all line protection applications (e.g. distance protection or line differential
protection) the parameter Base Current (i.e. IBase setting in the IED) used by the relevant
protection function, shall always be set equal to the largest rated CT primary current among all
CTs involved in the protection scheme. The rated CT primary current value is set as parameter
CTPrim under the IED TRM settings.
For all other protection applications (e.g. generator, shunt reactor, shunt capacitor and
transformer protection) it is typically desirable to set IBase parameter equal to the rated
current of the protected object. However this is only recommended to do if the rated current
of the protected object is within the range of 40% to 120% of the selected CT rated primary
current. If for any reason (e.g. high maximum short circuit current) the rated current of the
protected object is less than 40% of the rated CT primary current, it is strongly recommended
to set the parameter IBase in the IED to be equal to the largest rated CT primary current
among all CTs involved in the protection scheme and installed on the same voltage level. This
will effectively make the protection scheme less sensitive; however, such measures are
necessary in order to avoid possible problems with loss of the measurement accuracy in the
IED.
Regardless of the applied relationship between the IBase parameter and the rated CT primary
current, the corresponding minimum pickup of the function on the CT secondary side must
always be verified. It is strongly recommended that the minimum pickup of any instantaneous
protection function (e.g. differential, restricted earth fault, distance, instantaneous
overcurrent, etc.) shall under no circumstances be less than 4% of the used IED CT input rating
(i.e. 1A or 5A). This corresponds to 40mA secondary for IED 1A rated inputs and to 200mA
secondary for IED 5A rated inputs used by the function. This shall be individually verified for all
current inputs involved in the protection scheme.
Note that exceptions from the above 4% rule may be acceptable for very special applications
(e.g. when Multipurpose filter SMAIHPAC is involved in the protection scheme).
As the IED uses primary system quantities, the main VT ratios must be known to the IED. This
is done by setting the two parameters VTsec and VTprim for each voltage channel. The phase-
to-phase value can be used even if each channel is connected to a phase-to-earth voltage from
the VT.
132kV 110V
3 3
EQUATION2016 V1 EN-US (Equation 1)
The following setting should be used: VTprim=132 (value in kV) VTsec=110 (value in V)
4.2.4.2 Examples how to connect, configure and set VT inputs for most
commonly used VT connections SEMOD55055-60 v6
Figure 16 defines the marking of voltage transformer terminals commonly used around the
world.
+ + A a A da A a
(H1) (X1) (H1) (X1) (H1) (X1)
UPri USec
N n N dn B b
(H2) (X2) (H2) (X2) (H2) (X2)
a) b) c) d)
en06000591.vsd
IEC06000591 V1 EN-US
Where:
a) is the symbol and terminal marking used in this document. Terminals marked with a square indicate
the primary and secondary winding terminals with the same (positive) polarity
b) is the equivalent symbol and terminal marking used by IEC (ANSI) standard for phase-to-earth
connected VTs
c) is the equivalent symbol and terminal marking used by IEC (ANSI) standard for open delta
connected VTs
d) is the equivalent symbol and terminal marking used by IEC (ANSI) standard for phase-to-phase
connected VTs
It shall be noted that depending on national standard and utility practices the rated secondary
voltage of a VT has typically one of the following values:
• 100 V
• 110 V
• 115 V
• 120 V
• 230 V
The IED fully supports all of these values and most of them will be shown in the following
examples.
Figure 17 gives an example on how to connect a three phase-to-earth connected VT to the IED.
It gives an overview of required actions by the user in order to make this measurement
available to the built-in protection and control functions within the IED.
For correct terminal designations, see the connection diagrams valid for the
delivered IED.
L1
L2 IED
L3 2
3
66 kV
5
3 1
110V
3
SMAI2
BLOCK AI3P
REVROT AI1
^GRP2L1 AI2
^GRP2L2 AI3
66 kV ^GRP2L3 AI4
#Not used ^GRP2N AIN
3
110V
3
4
66 kV
3 IEC06000599-4-en.vsdx
110V
3
IEC06000599 V4 EN-US
L1
L2 IED
2
3
132 kV
2 1
110V
2
SMAI2
BLOCK AI2P
^GRP2L1 AI1
^GRP2L2 5 AI2
132 kV ^GRP2L1L2 AI3
^GRP2N AI4
2 AIN
110V
2 4
IEC16000140-1-en.vsdx
IEC16000140 V1 EN-US
Where:
1) shows how to connect three secondary phase-to-earth voltages to three VT inputs on the IED
2) is the TRM where these three voltage inputs are located. For these three voltage inputs, the
following setting values shall be entered:
VTprim =132 kV
VTsec = 110 V
Inside the IED, only the ratio of these two parameters is used. It shall be noted that the ratio of
the entered values exactly corresponds to ratio of one individual VT.
66
66 3
=
110 110
3
EQUATION1903 V1 EN-US (Equation 2)
3) are three connections made in Signal Matrix Tool (SMT), which connect these three voltage
inputs to first three input channels of the preprocessing function block 5). Depending on the
type of functions which need this voltage information, more then one preprocessing block might
be connected in parallel to these three VT inputs.
4) shows that in this example the fourth (that is, residual) input channel of the preprocessing block
is not connected in SMT tool. Thus the preprocessing block will automatically calculate 3Uo
inside by vectorial sum from the three phase to earth voltages connected to the first three input
channels of the same preprocessing block. Alternatively, the fourth input channel can be
connected to open delta VT input, as shown in Figure 20.
5) is a Preprocessing block that has the task to digitally filter the connected analog inputs and
calculate:
These calculated values are then available for all built-in protection and control functions within
the IED, which are connected to this preprocessing function block in the configuration tool. For
this application most of the preprocessing settings can be left to the default values. However the
following settings shall be set as shown here:
UBase=66 kV (that is, rated Ph-Ph voltage)
If frequency tracking and compensation is required (this feature is typically required only for IEDs
installed in the generating stations) then the setting parameters DFTReference shall be set
accordingly.
Figure 19 gives an example how to connect a phase-to-phase connected VT to the IED. It gives
an overview of the required actions by the user in order to make this measurement available to
the built-in protection and control functions within the IED. It shall be noted that this VT
connection is only used on lower voltage levels (that is, rated primary voltage below 40 kV).
L1
L2
L3
13.8kV 13.8kV IED
120V 120V
3 5
1
SMAI2
BLOCK AI3P
REVROT AI1
^GRP2L1 AI2
^GRP2L2 AI3
^GRP2L3 AI4
#Not Used ^GRP2N AIN
IEC06000600-5-en.vsdx
.
IEC06000600 V5 EN-US
Where:
1) shows how to connect the secondary side of a phase-to-phase VT to the VT inputs on the IED
2) is the TRM where these three voltage inputs are located. It shall be noted that for these three
voltage inputs the following setting values shall be entered:
VTprim=13.8 kV
VTsec=120 V
Please note that inside the IED only ratio of these two parameters is used.
3) are three connections made in the Signal Matrix tool (SMT), Application configuration tool (ACT),
which connects these three voltage inputs to first three input channels of the preprocessing
function block 5). Depending on the type of functions, which need this voltage information, more
than one preprocessing block might be connected in parallel to these three VT inputs
4) shows that in this example the fourth (that is, residual) input channel of the preprocessing block is
not connected in SMT. Note. If the parameters UL1, UL2, UL3, UN should be used the open delta must
be connected here.
5) Preprocessing block has a task to digitally filter the connected analog inputs and calculate:
These calculated values are then available for all built-in protection and control functions within the
IED, which are connected to this preprocessing function block in the configuration tool. For this
application most of the preprocessing settings can be left to the default values. However the
following settings shall be set as shown here:
ConnectionType=Ph-Ph
UBase=13.8 kV
If frequency tracking and compensation is required (this feature is typically required only for IEDs
installed in the generating stations) then the setting parameters DFTReference shall be set
accordingly.
4.2.4.5 Example on how to connect an open delta VT to the IED for high
impedance earthed or unearthed networks SEMOD55055-163 v9
Figure 20 gives an example about the wiring of an open delta VT to the IED for high impedance
earthed or unearthed power systems. It shall be noted that this type of VT connection
presents a secondary voltage proportional to 3U0 to the IED.
In case of a solid earth fault close to the VT location the primary value of 3Uo will be equal to:
3U 0 = 3 × U Ph - Ph = 3 × U Ph - N
EQUATION1921 V3 EN-US (Equation 3)
The primary rated voltage of an open Delta VT is always equal to UPh-E. Three series connected
VT secondary windings gives a secondary voltage equal to three times the individual VT
secondary winding rating. Thus the secondary windings of open delta VTs quite often have a
secondary rated voltage equal to one third of the rated phase-to-phase VT secondary voltage
(110/3V in this particular example).
Figure 20 gives overview of required actions by the user in order to make this measurement
available to the built-in protection and control functions within the IED as well.
L1
L2 IED
L3
2
6.6kV
3
110V
3 5
3
SMAI2
BLOCK AI3P
6.6kV 1 REVROT AI1
# Not Used ^GRP2L1 AI2
3 # Not Used ^GRP2L2 AI3
110V # Not Used ^GRP2L3 AI4
^GRP2N AIN
3 +3Uo
4
6.6kV
IEC06000601-4-en.vsdx
3
110V
3
IEC06000601 V4 EN-US
Figure 20: Open delta connected VT in high impedance earthed power system
Where:
1) shows how to connect the secondary side of the open delta VT to one VT input on the IED.
2) is the TRM where this voltage input is located. It shall be noted that for this voltage input the
following setting values shall be entered:
110
VT sec = 3 × = 110V
3
EQUATION1924 V1 EN-US (Equation 5)
Inside the IED, only the ratio of these two parameters is used. It shall be noted that the ratio of
the entered values exactly corresponds to ratio of one individual open delta VT.
6.6
3 × 6.6 3
=
110 110
3
EQUATION1925 V1 EN-US (Equation 6)
3) shows that in this example the first three input channel of the preprocessing block is not
connected in SMT tool or ACT tool.
4) shows the connection made in Signal Matrix Tool (SMT), Application configuration tool (ACT),
which connect this voltage input to the fourth input channel of the preprocessing function block
5).
5) is a Preprocessing block that has the task to digitally filter the connected analog input and
calculate:
These calculated values are then available for all built-in protection and control functions within
the IED, which are connected to this preprocessing function block in the configuration tool. For
this application most of the preprocessing settings can be left to the default values.
If frequency tracking and compensation is required (this feature is typically required only for IEDs
installed in the generating stations ) then the setting parameters DFTReference shall be set
accordingly.
4.2.4.6 Example how to connect the open delta VT to the IED for low impedance
earthed or solidly earthed power systems SEMOD55055-199 v6
Figure 21 gives an example about the connection of an open delta VT to the IED for low
impedance earthed or solidly earthed power systems. It shall be noted that this type of VT
connection presents secondary voltage proportional to 3U0 to the IED.
In case of a solid earth fault close to the VT location the primary value of 3Uo will be equal to:
U Ph - Ph
3Uo = = U Ph - E
3
EQUATION1926 V1 EN-US (Equation 7)
The primary rated voltage of such VT is always equal to UPh-E Therefore, three series
connected VT secondary windings will give the secondary voltage equal only to one individual
VT secondary winding rating. Thus the secondary windings of such open delta VTs quite often
has a secondary rated voltage close to rated phase-to-phase VT secondary voltage, that is,
115V or 115/√3V as in this particular example. Figure 21 gives an overview of the actions which
are needed to make this measurement available to the built-in protection and control
functions within the IED.
L1
L2 IED
L3 2
138kV
3 5
115V
3
3
SMAI2
1 BLOCK AI3P
138kV REVROT AI1
# Not Used ^GRP2L1 AI2
3 # Not Used ^GRP2L2 AI3
115V # Not Used ^GRP2L3 AI4
3 +3Uo ^GRP2N AIN
4
138 kV
3
115V
3
IEC06000602-4-en.vsdx
IEC06000602 V4 EN-US
Figure 21: Open delta connected VT in low impedance or solidly earthed power system
Where:
1) shows how to connect the secondary side of open delta VT to one VT input in
the IED.
2) is TRM where this voltage input is located. It shall be noted that for this voltage
input the following setting values shall be entered:
138
VTprim = 3× = 138kV
3
EQUATION1928 V1 EN-US (Equation 8)
115
VT sec = 3× = 115V
3
EQUATION1929 V1 EN-US (Equation 9)
Inside the IED, only the ratio of these two parameters is used. It shall be noted
that the ratio of the entered values exactly corresponds to ratio of one
individual open delta VT.
138
138 3
=
115 115
3
EQUATION1930 V1 EN-US (Equation 10)
3) shows that in this example the first three input channel of the preprocessing
block is not connected in SMT tool.
4) shows the connection made in Signal Matrix Tool (SMT), which connect this
voltage input to the fourth input channel of the preprocessing function block 4).
5) preprocessing block has a task to digitally filter the connected analog inputs
and calculate:
These calculated values are then available for all built-in protection and control
functions within the IED, which are connected to this preprocessing function
block in the configuration tool. For this application most of the preprocessing
settings can be left to the default values.
If frequency tracking and compensation is required (this feature is typically
required only for IEDs installed in the generating stations) then the setting
parameters DFTReference shall be set accordingly.
Figure 22 gives an example on how to connect a neutral point VT to the IED. This type of VT
connection presents secondary voltage proportional to U0 to the IED.
In case of a solid earth fault in high impedance earthed or unearthed systems the primary
value of Uo voltage will be equal to:
UPh - Ph
U0 = = UPh - E
3
EQUATION1931 V2 EN-US (Equation 11)
Figure 22gives an overview of required actions by the user in order to make this measurement
available to the built-in protection and control functions within the IED.
IED
Protected Object
2
5
L1 L2 L3
SMAI2
BLOCK AI3P
REVROT AI1
# Not Used ^GRP2L1 AI2
1
# Not Used ^GRP2L2 AI3
# Not Used ^GRP2L3 AI4
^GRP2N AIN
R
Uo
4
6.6kV IEC06000603-4-en.vsdx
3
100V
IEC06000603 V4 EN-US
Where:
1) shows how to connect the secondary side of neutral point VT to one VT input in the IED.
2) is the TRM or AIM where this voltage input is located. For this voltage input the following setting
values shall be entered:
6.6
VTprim = = 3.81kV
3
EQUATION1933 V1 EN-US (Equation 12)
VT sec 100V
EQUATION1934 V2 EN-US (Equation 13)
Inside the IED, only the ratio of these two parameters is used. It shall be noted that the ratio of the
entered values exactly corresponds to ratio of the neutral point VT.
Table continues on next page
3) shows that in this example the first three input channel of the preprocessing block is not connected
in SMT tool or ACT tool.
4) shows the connection made in Signal Matrix Tool (SMT), Application configuration tool (ACT), which
connects this voltage input to the fourth input channel of the preprocessing function block 5).
5) is a preprocessing block that has the task to digitally filter the connected analog inputs and
calculate:
These calculated values are then available for all built-in protection and control functions within the
IED, which are connected to this preprocessing function block in the configuration tool. For this
application, most of the preprocessing settings can be left to the default values.
If frequency tracking and compensation is required (this feature is typically required only for IEDs
installed in the generating stations) then the setting parameters DFTReference shall be set
accordingly.
IEC13000239-3-en.vsd
IEC13000239 V3 EN-US
• Keypad
• Display (LCD)
• LED indicators
• Communication port for PCM600
The LHMI includes a graphical monochrome liquid crystal display (LCD) with a resolution of 320
x 240 pixels. The character size can vary. The amount of characters and rows fitting the view
depends on the character size and the view that is shown.
IEC15000270-1-en.vsdx
IEC15000270 V1 EN-US
1 Path
2 Content
3 Status
4 Scroll bar (appears when needed)
The function key button panel shows on request what actions are possible with the function
buttons. Each function button has a LED indication that can be used as a feedback signal for
the function button control action. The LED is connected to the required signal with PCM600.
IEC13000281-1-en.vsd
GUID-C98D972D-D1D8-4734-B419-161DBC0DC97B V1 EN-US
IEC13000240-1-en.vsd
GUID-5157100F-E8C0-4FAB-B979-FD4A971475E3 V1 EN-US
The LHMI includes three status LEDs above the display: Ready, Start and Trip.
There are 15 programmable indication LEDs on the front of the LHMI. Each LED can indicate
three states with the colors: green, yellow and red. The texts related to each three-color LED
are divided into three panels.
There are 3 separate panels of LEDs available. The 15 physical three-color LEDs in one LED
group can indicate 45 different signals. Altogether, 135 signals can be indicated since there are
three LED groups. The LEDs are lit according to priority, with red being the highest and green
the lowest priority. For example, if on one panel there is an indication that requires the green
LED to be lit, and on another panel there is an indication that requires the red LED to be lit, the
red LED takes priority and is lit. The LEDs can be configured with PCM600 and the operation
mode can be selected with the LHMI or PCM600.
Information panels for the indication LEDs are shown by pressing the Multipage button.
Pressing that button cycles through the three pages. A lit or un-acknowledged LED is indicated
with a highlight. Such lines can be selected by using the Up/Down arrow buttons. Pressing the
Enter key shows details about the selected LED. Pressing the ESC button exits from
information pop-ups as well as from the LED panel as such.
The Multipage button has a LED. This LED is lit whenever any LED on any panel is lit. If there are
un-acknowledged indication LEDs, then the Multipage LED blinks. To acknowledge LEDs, press
the Clear button to enter the Reset menu (refer to description of this menu for details).
There are two additional LEDs which are next to the control buttons and . These
LEDs can indicate the status of two arbitrary binary signals by configuring the
OPENCLOSE_LED function block. For instance, OPENCLOSE_LED can be connected to a circuit
breaker to indicate the breaker open/close status on the LEDs.
IEC16000076-1-en.vsd
IEC16000076 V1 EN-US
The LHMI keypad contains push-buttons which are used to navigate in different views or
menus. The push-buttons are also used to acknowledge alarms, reset indications, provide help
and switch between local and remote control mode.
The keypad also contains programmable push-buttons that can be configured either as menu
shortcut or control buttons.
24
1
23
2
18
3
19
4
6 20
21
7 22
8 9 10 11 12 13 14 15 16 17
IEC15000157-2-en.vsd
IEC15000157 V2 EN-US
Figure 28: LHMI keypad with object control, navigation and command push-buttons and
RJ-45 communication port
22 Communication port
23 Programmable indication LEDs
24 IED status LEDs
Protection indicators
The protection indicator LEDs are Ready, Start and Trip.
The yellow and red status LEDs are configured in the disturbance recorder
function, DRPRDRE, by connecting a start or trip signal from the actual function
to a BxRBDR binary input function block using the PCM600 and configure the
setting to Off, Start or Trip for that particular signal.
Flashing The IED is in test mode and protection functions are blocked, or the IEC61850
protocol is blocking one or more functions.
The indication disappears when the IED is no longer in test mode and blocking
is removed. The blocking of functions through the IEC61850 protocol can be
reset in Main menu/Test/Reset IEC61850 Mod. The yellow LED changes to
either ON or OFF state depending on the state of operation.
Alarm indicators
The 15 programmable three-color LEDs are used for alarm indication. An individual alarm/
status signal, connected to any of the LED function blocks, can be assigned to one of the three
LED colors when configuring the IED.
The LHMI is used to access the relay parameters. Three types of parameters can be read and
written.
• Numerical values
• String values
• Enumerated values
Numerical values are presented either in integer or in decimal format with minimum and
maximum values. Character strings can be edited character by character. Enumerated values
have a predefined set of selectable values.
• The green uplink LED on the left is lit when the cable is successfully connected to the port.
• The yellow LED is not used; it is always off.
IEC13000280-1-en.vsd
GUID-AACFC753-BFB9-47FE-9512-3C4180731A1B V1 EN-US
1 RJ-45 connector
2 Green indicator LED
The default IP address for the IED front port is 10.1.150.3 and the corresponding subnetwork
mask is 255.255.254.0. It can be set through the local HMI path Main menu/Configuration/
Communication/Ethernet configuration/FRONT port/AP_FRONT.
Do not connect the IED front port to a LAN. Connect only a single local PC with
PCM600 to the front port. It is only intended for temporary use, such as
commissioning and testing.
SYMBOL-CC V2 EN-US
SEMOD54734-4 v8
The 1Ph High impedance differential protection function HZPDIF can be used as:
Three instances of HZPDIF are used as a busbar protection for one busbar zone.
3·Id
IEC10000185_2_en.vsd
IEC10000185 V2 EN-US
Figure 30: Application of a 1Ph High impedance differential protection HZPDIF function
as busbar protection
Id
IEC05000177-2-en.vsd
IEC05000177 V2 EN-US
Figure 31: Application of a 1Ph High impedance differential protection HZPDIF function
The high impedance differential protection principle has been used for many years and is well
documented in literature publicly available. Its operating principle provides very good
sensitivity and high speed operation. One main benefit offered by the principle is an absolute
stability (that is, no operation) for external faults even in the presence of heavy CT saturation.
The principle is based on the CT secondary current circulating between involved current
transformers and not through the IED due to high impedance in the measuring branch. This
stabilizing resistance is in the range of hundreds of ohms and sometimes above one kilo Ohm.
When an internal fault occurs the current cannot circulate and is forced through the measuring
branch causing relay operation.
It should be remembered that the whole scheme, its built-in components and wiring must be
adequately maintained throughout the lifetime of the equipment in order to be able to
withstand the high voltage peaks (that is, pulses) which may appear during an internal fault.
Otherwise any flash-over in CT secondary circuits or any other part of the scheme may prevent
correct operation of the high impedance differential relay for an actual internal fault.
Id Metrosil
IEC05000164-2-en.vsd
IEC05000164 V3 EN-US
Figure 32: Example for the high impedance restricted earth fault protection application
For a through fault one current transformer might saturate when the other CTs still will feed
current. For such a case a voltage will be developed across the measuring branch. The
calculations are made with the worst situations in mind and a minimum operating voltage UR
is calculated according to equation 14
where:
IFmax is the maximum through fault current at the secondary side of the CT
Rct is the current transformer secondary winding resistance and
Rl is the maximum loop resistance of the circuit at any CT.
The minimum operating voltage has to be calculated (all loops) and the IED function is set
higher than the highest achieved value (setting U>Trip). As the loop resistance is the value to
the connection point from each CT, it is advisable to do all the CT core summations in the
switchgear to have shortest possible loops. This will give lower setting values and also a better
balanced scheme. The connection in to the control room can then be from the most central
bay.
For an internal fault, all involved CTs will try to feed current through the measuring branch.
Depending on the size of current transformer, relatively high voltages will be developed across
the series resistor. Note that very high peak voltages can appear. To prevent the risk of
flashover in the circuit, a voltage limiter must be included. The voltage limiter is a voltage
dependent resistor (Metrosil).
The external unit with stabilizing resistor has a value of either 6800 ohms or 1800 ohms
(depending on ordered alternative) with a sliding link to allow adjustment to the required
value. Select a suitable value of the resistor based on the UR voltage calculated. A higher
resistance value will give a higher sensitivity and a lower value a lower sensitivity of the relay.
The function has a recommended operating current range 40 mA to 1.0A for 1 A inputs and 200
mA to 5A for 5A inputs. This, together with the selected and set value, is used to calculate the
required value of current at the set U>Trip and SeriesResitor values.
The CT inputs used for 1Ph High impedance differential protection HZPDIF
function, shall be set to have ratio 1:1. So the parameters CTsecx and CTprimx of
the relevant channel x of TRM and/or AIM shall be set equal to 1 A by PST in
PCM600; The parameter CTStarPointx may be set to ToObject.
The tables 10, 11 below show, the operating currents for different settings of operating
voltages and selected resistances. Adjust as required based on tables 10, 11 or to values in
between as required for the application.
Minimum ohms can be difficult to adjust due to the small value compared to
the total value.
Normally the voltage can be increased to higher values than the calculated minimum U>Trip
with a minor change of total operating values as long as this is done by adjusting the resistor
to a higher value. Check the sensitivity calculation below for reference.
The current transformer saturation voltage must be at least 2 ˣ U>Trip to have sufficient
operating margin. This must be checked after calculation of U>Trip.
When the R value has been selected and the U>Trip value has been set, the sensitivity of the
scheme IP can be calculated. The IED sensitivity is decided by the total current in the circuit
according to equation 15.
IP = n × ( IR + Ires + å lmag )
EQUATION1747 V1 EN-US (Equation 15)
where:
n is the CT ratio
IP primary current at IED pickup,
IR IED pickup current (U>Trip/SeriesResistor)
Ires is the current through the voltage limiter and
ΣImag is the sum of the magnetizing currents from all CTs in the circuit (for example, 4 for
restricted earth fault protection, 2 for reactor differential protection, 3-5 for
autotransformer differential protection).
It should be remembered that the vectorial sum of the currents must be used (IEDs, Metrosil
and resistor currents are resistive). The current measurement is insensitive to DC component
in fault current to allow the use of only the AC components of the fault current in the above
calculations.
The series resistor is dimensioned for 200 W. Preferable the U>Trip2/SeriesResistor should
always be lower than 200 W to allow continuous activation during testing. If this value is
exceeded, testing should be done with a transient faults.
Rl Rl
Rct UR Rct
R
Rres
I>
Protected Object
UR
UR
UR
Figure 33: The high impedance principle for one phase with two current transformer
inputs
L1 L2 L3
(A) (B) (C)
7 SMAI2
1 BLOCK G2AI3P
AI01 REVROT G2AI1
CT 1200/1 2 (I) ^GRP2L1 G2AI2
5
AI03
6 (I)
7
AI04
8 (I)
9
1
AI05
0 (I)
1 1
1
1
AI06
2 (I)
Protected Object IED
N
L3 (C)
L2 (B)
L1 (A)
N 4
L3 (C)
L2 (B)
CT 1200/1 L1 (A) 5
Star/Wye
Connected X1 11 12 13 14 1 2 3 4 5 6 7
2
3
1
1
3
3
R4
R5
R6
R1
R2
R3
2 U
2 U
2 U
4
2
L1 L2 L3 X X 6
(A) (B) (C) 3-Ph Plate with Metrosils and Resistors
IEC07000193-5-en.vsdx
IEC07000193 V5 EN-US
Pos Description
1 Scheme earthing point
It is important to insure that only one earthing point exist in this scheme.
2 Three-phase plate with setting resistors and metrosils. Protective earth is a separate 4 mm screw
terminal on the plate.
3 Necessary connection for three-phase metrosil set.
4 Position of optional test switch for secondary injection into the high impedance differential IED.
5 Necessary connection for setting resistors.
The star point connector must be removed for installations with 650 series IEDs.
This star point is required for RADHA schemes only.
7 Connections of three individual phase currents for high impedance scheme to three CT inputs in the
IED.
6.1.3.2 Connections for 1Ph High impedance differential protection HZPDIF GUID-D68A237F-610C-4AF0-870F-273117F64D92 v10
Restricted earth fault protection is a typical application for 1Ph High impedance differential
protection HZPDIF. Typical CT connections for the high impedance based protection scheme
are shown in figure 35.
L1 L2 L3
(A) (B) (C)
BLOCK G2AI3P
5 REVROT G2AI1
6 6 AI03 (I) ^GRP2L1 G2AI2
^GRP2L2 G2AI3
7
8 AI04 (I) ^GRP2L3 G2AI4
^GRP2N G2N
9
10 AI05 (I)
11
Protected Object 12 AI06 (I)
L1 L2 L3
IED
N
(A) (B) (C)
4
1
N
CT 1500/5
X1 4 5 1 2 3
2
3
5
1
1
3
R1
R2
U
4
2
IEC07000194 V5 EN-US
Pos Description
1 Scheme earthing point
2 One-phase plate with stabilizing resistor and metrosil. Protective earth is a separate 4 mm screw
terminal on the plate.
3 Necessary connection for the metrosil.
4 Position of optional test switch for secondary injection into the high impedance differential IED.
5 Necessary connection for stabilizing resistor.
6 How to connect the high impedance restricted earth fault protection scheme to one CT input in IED.
M13076-3 v2
The setting calculations are individual for each application. Refer to the different application
descriptions below.
Operation: The operation of the high impedance differential function can be switched On or
Off.
U>Alarm: Set the alarm level. The sensitivity can roughly be calculated as a certain percentage
of the selected Trip level. A typical setting is 10% of U>Trip This alarm stage can be used for
scheme CT supervision.
tAlarm: Set the time delay for the alarm. A typical setting is 2-3 seconds.
U>Trip: Set the trip level according to the calculations (see examples below for a guidance).
The level is selected with margin to the calculated required voltage to achieve stability. Values
can be within 20V - 400V range dependent on the application.
SeriesResistor: Set the value of the used stabilizing series resistor. Calculate the value
according to the examples for each application. Adjust the resistor as close as possible to the
calculated value. Measure the value achieved and set this value for this parameter.
The value shall always be high impedance. This means for example, for 1A
circuits say bigger than 400 ohms (400 VA) and for 5 A circuits say bigger than
100 ohms (2500 VA). This ensures that the current will circulate and not go
through the differential circuit at through faults.
That the settings of U>Alarm, U>Trip and SeriesResistor must be chosen such
that both U>Alarm/SeriesResistor and U>Trip/SeriesResistor are >4% of
IRated of the used current input. Normally the settings shall also be such that
U>Alarm/SeriesResistor and U>Trip/SeriesResistor both gives a value
<4*IRated of the used current input. If not, the limitation in how long time the
actual current is allowed to persist not to overload the current input must be
considered especially during the secondary testing.
In many busbar arrangements such as one-and a half breaker, ring breaker, mesh corner, there
will be a T-feeder from the current transformer at the breakers up to the current transformers
in the feeder circuit (for example, in the transformer bushings). It is often required to separate
the protection zones that the feeder is protected with one scheme while the T-zone is
protected with a separate differential protection scheme. The 1Ph high impedance differential
HZPDIF function in the IED allows this to be done efficiently, see Figure 36.
3·Id
IEC05000165-2-en.vsd
IEC05000165 V2 EN-US
3·Id
IEC05000739-2-en.vsd
IEC05000739 V2 EN-US
Figure 36: The protection scheme utilizing the high impedance function for the T-feeder
Normally this scheme is set to achieve a sensitivity of around 20 percent of the used CT
primary rating so that a low ohmic value can be used for the series resistor.
Setting example
Basic data:
Current transformer ratio: 2000/1 A
CT Class: 20 VA 5P20
Secondary resistance: 6.2 ohms
Cable loop resistance: <100 m 2.5 mm2 (one way) gives 2 ˣ 0.8 ohm at 75° C
Max fault current: Equal to switchgear rated fault current 40 kA
Calculation:
Check from the table of selected resistances the required series stabilizing resistor value to
use. As this application requires to be so sensitive select SeriesResistor= 2000 ohm, which
gives an IED operating current of 100 mA.
Calculate the primary sensitivity at operating voltage using the following equation.
2000
IP = (100 0° + 20 0° + 3 × 10 −60° ) × 10−3 ≤ approx 275 A
1
EQUATION1209 V2 EN-US (Equation 18)
where
100 mA is the current drawn by the IED circuit and
10 mA is the current drawn by each CT just at pickup
20 mA is current drawn by metrosil at pickup
The magnetizing current is taken from the magnetizing curve for the current transformer
cores which should be available. The current value at U>Trip is taken. For the voltage
dependent resistor current the peak value of voltage 200 ˣ √2 is used. Then the RMS current is
calculated by dividing obtained current value from the metrosil curve with√2. Use the value
from the maximum metrosil curve given in Figure 38
It can clearly be seen that the sensitivity is not so much influenced by the selected voltage level
so a sufficient margin should be used. The selection of the stabilizing resistor and the level of
the magnetizing current (mostly dependent of the number of turns) are the most important
factors.
Reactive power equipment (for example shunt reactors and/or shunt capacitors) can be
connected to the tertiary winding of the power transformers. The 1Ph High impedance
differential protection function HZPDIF can be used to protect the tertiary reactor for phase
faults as well as earth faults if the power system of the tertiary winding is direct or low
impedance earthed.
3·Id
IEC05000176-3-en.vsd
IEC05000176 V3 EN-US
Figure 37: Application of the1Ph High impedance differential protection HZPDIF function on a reactor
Setting example
Basic data:
Current transformer ratio: 100/5 A (Note: Must be the same at all locations)
CT Class: 10 VA 5P20
Secondary resistance: 0.26 ohms
Cable loop resistance: <50 m 2.5mm2 (one way) gives 1 ˣ 0.4 ohm at 75° C
Note! Only one way as the tertiary power system earthing is limiting
the earth-fault current. If high earth-fault current exists use two way
cable length.
Max fault current: The maximum through fault current is limited by the reactor
reactance and the inrush will be the worst for a reactor for example,
800 A.
Calculation:
800
UR > × (0.26 + 0.4) = 26, 4
100 / 5
EQUATION1216 V2 EN-US (Equation 19)
10
U _ CT _ Saturation > + 0.26 × 20 × 5 = 66V
25
EQUATION1217 V2 EN-US (Equation 20)
Check from the table of selected resistances the required series stabilizing resistor value to
use. Since this application requires good sensitivity, select SeriesResistor = 300 ohm, which
gives an IED current of 100 mA.
To calculate the sensitivity at operating voltage, refer to equation 21, which gives an
acceptable value. A little lower sensitivity could be selected by using a lower resistance value.
100
IP = × (100 0° + 5 0° + 2 × 100 −60° ) × 10−3 ≤ approx 5 A
5
EQUATION1218 V2 EN-US (Equation 21)
The magnetizing current is taken from the magnetizing curve of the current transformer cores,
which should be available. The current value at U>Trip is taken. For the voltage dependent
resistor current the peak value of voltage 30 ˣ √2 is used. Then the RMS current is calculated by
dividing obtained current value from the metrosil curve with √2. Use the maximum value from
the metrosil curve given in Figure 38.
The 1Ph High impedance differential protection HZPDIF function has a separate alarm level,
which can be used to give alarm for problems with an involved current transformer circuit. The
setting level is normally selected to be around 10% of the operating voltage U>Trip.
As seen in the setting examples above the sensitivity of HZPDIF function is normally high,
which means that the function will in many cases operate also for short circuits or open
current transformer secondary circuits. However the stabilizing resistor can be selected to
achieve sensitivity higher than normal load current and/or separate criteria can be added to
the operation, like a check zone. This can be either another IED, with the same HZPDIF
function, or be a check about the fault condition, which is performed by an earth overcurrent
function or neutral point voltage function.
For such cases where operation is not expected during normal service the alarm output should
be used to activate an external shorting of the differential circuit avoiding continuous high
voltage in the circuit. A time delay of a few seconds is used before the shorting and alarm are
activated. Auxiliary relays with contacts that can withstand high voltage shall be used, like
RXMVB types.
IEC05000749 V1 EN-US
Figure 38: Current voltage characteristics for the non-linear resistors, in the range 10-200 V, the
average range of current is: 0.01–10 mA
7.1.1 Identification
M14885-1 v6
TOC-REVA V2 EN-US
Directional phase overcurrent protection, four steps OC4PTOC is used in several applications
in the power system. Some applications are:
In many applications several steps with different current pickup levels and time delays are
needed. OC4PTOC can have up to four different, individually settable steps. The following
options are possible:
If VT inputs are not available or not connected, the setting parameter DirModex
(x = step 1, 2, 3 or 4) shall be left to the default value Non-directional.
Choice of time delay characteristics: There are several types of time delay characteristics
available such as definite time delay and different types of inverse time delay characteristics.
The selectivity between different overcurrent protections is normally enabled by co-ordination
between the function time delays of the different protections. To enable optimal co-ordination
between all overcurrent protections, they should have the same time delay characteristic.
Therefore, a wide range of standardized inverse time characteristics are available for IEC and
ANSI. It is also possible to tailor make the inverse time characteristic.
Normally, it is required that the phase overcurrent protection shall reset as fast as possible
when the current level gets lower than the operation level. In some cases some sort of delayed
reset is required. Therefore, different kinds of reset characteristics can be used.
For some protection applications, there can be a need to change the current pick-up level for
some time. A typical case is when the protection will measure the current to a large motor. At
the start up sequence of a motor the start current can be significantly larger than the rated
current of the motor. Therefore, there is a possibility to give a setting of a multiplication factor
to the current pick-up level. This multiplication factor is activated from a binary input signal to
the function.
Power transformers can have a large inrush current, when being energized. This phenomenon
is due to saturation of the transformer magnetic core during parts of the period. There is a
risk that inrush current will reach levels above the pick-up current of the phase overcurrent
protection. The inrush current has a large 2nd harmonic content. This can be used to avoid
unwanted operation of the protection function. Therefore, OC4PTOC has a possibility of 2nd
harmonic restrain if the level of 2nd harmonic current reaches a value above a set percent of the
fundamental current.
The phase overcurrent protection is often used as a protection for two and three phase short
circuits. In some cases, it is not wanted to detect single-phase earth faults by the phase
overcurrent protection. This fault type is detected and cleared after operation of earth fault
protection. Therefore, it is possible to make a choice how many phases, at minimum, that have
to have current above the pick-up level, to enable operation. If set 1 of 3 it is sufficient to have
high current in one phase only. If set 2 of 3 or 3 of 3 single-phase earth faults are not detected.
M12982-4 v14
The parameters for the directional phase overcurrent protection, four steps OC4PTOC are set
via the local HMI or PCM600.
Common base IED values for the primary current (IBase), primary voltage (UBase) and primary
power (SBase) are set in global base values for settings function GBASVAL.
GlobalBaseSel: Selects the global base value group used by the function to define IBase, UBase
and SBase.
MeasType: Selection of discrete Fourier filtered (DFT) or true RMS filtered (RMS) signals. RMS
is used when the harmonic contents are to be considered, for example in applications with
shunt capacitors.
AngleRCA: Protection characteristic angle set in degrees. If the angle of the fault loop current
has the angle RCA, the direction to the fault is forward.
AngleROA: Angle value, given in degrees, to define the angle sector of the directional function,
shown in Figure 39.
StartPhSel: Number of phases, with high current, required for operation. The setting
possibilities are: 1 out of 3, 2 out of 3 and 3 out of 3. The default setting is 1 out of 3.
IMinOpPhSel: Minimum current setting level for releasing the directional start signals in % of
IB. This setting should be less than the lowest step setting. The default setting is 7% of IB.
2ndHarmStab: Operate level of 2nd harmonic current restrain set in % of the fundamental
current. The setting range is 5 - 100% in steps of 1%. The default setting is 20%.
Uref
2
4
Idir
IEC09000636_2_vsd
IEC09000636 V2 EN-US
Characteristx: Selection of time characteristic for step x. Definite time delay and different
types of inverse time characteristics are available according to Table 12.
Ix>Max and Ix>Min should only be changed if remote setting of operation current level, Ix>, is
used. The limits are used for decreasing the used range of the Ix> setting. If Ix> is set outside
Ix>Max and Ix>Min, the closest of the limits to Ix> is used by the function. If Ix>Max is smaller
than Ix>Min, the limits are swapped.
tx: Definite time delay for step x. The definite time tx is added to the inverse time when inverse
time characteristic is selected. Note that the value set is the time between activation of the
start and the trip outputs.
IMinx: Minimum operate current in % of IB for all inverse time characteristics, below which no
operation takes place.
IMinx: Minimum operate current for step x in % of IBase. Set IMinx below Ix> for every step to
achieve ANSI reset characteristic according to standard. If IMinx is set above Ix> for any step
the ANSI reset works as if current is zero when current drops below IMinx.
txMin: Minimum operate time for all inverse time characteristics. At high currents the inverse
time characteristic might give a very short operation time. By setting this parameter the
operation time of the step can never be shorter than the setting. Setting range: 0.000 -
60.000s in steps of 0.001s.
IxMult: Multiplier for scaling of the current setting value. If a binary input signal ENMULTx
(enableMultiplier) is activated the current operation level is increased by this setting constant.
Setting range: 1.0-10.0
Operate time
tx
txMin
IMinx Current
IEC10000058
IEC10000058 V2 EN-US
Figure 40: Minimum operate current and operate time for inverse time characteristics
In order to fully comply with the definition of the curve, the setting parameter txMin shall be
set to a value equal to the operating time of the selected inverse curve for twenty times the set
current pickup value. Note that the operate time is dependent on the selected time multiplier
setting kx.
ResetTypeCrvx: The reset of the delay timer can be made as shown in Table 13.
The delay characteristics are described in Technical manual. There are some restrictions
regarding the choice of the reset delay.
For the definite time delay characteristics, the possible delay time setting instantaneous (1)
and IEC (2 = set constant time reset).
For ANSI inverse time characteristics, all three types of reset time characteristics are available:
instantaneous (1), IEC (2 = set constant time reset) and ANSI (3 = current dependent reset
time).
For IEC inverse time characteristics, the possible delay time settings are instantaneous (1) and
IEC (2 = set constant time reset).
For the customer tailor-made inverse time delay characteristics (type 17), all three types of
reset time characteristics are available: instantaneous (1), IEC (2 = set constant time reset) and
ANSI (3 = current dependent reset time). If the current-dependent type is used, settings pr, tr
and cr must be given.
tPCrvx, tACrvx, tBCrvx, tCCrvx: These parameters are used by the customer to create the
inverse time characteristic curve. See equation 22 for the time characteristic equation. For
more information, refer to Technical manual.
æ ö
ç A ÷
t [s] = ç + B ÷ × IxMult
çæ ö ÷
p
i
çç ÷ -C ÷
è è in > ø ø
EQUATION1261 V2 EN-US (Equation 22)
tPRCrvx, tTRCrvx, tCRCrvx: These parameters are used by the customer to create the inverse
reset time characteristic curve. For more information, refer to Technical manual.
HarmRestrainx: Enables the block of step x from the harmonic restrain function (2nd
harmonic). This function should be used when there is a risk of an unwanted trip caused by
power transformer inrush currents. It can be set to Off/On.
Directional phase overcurrent protection, four steps can be used in different ways, depending
on the application where the protection is used. A general description is given below.
The operating current setting of the inverse time protection, or the lowest current step of the
definite time protection, must be defined so that the highest possible load current does not
cause protection operation. The protection reset current must also be considered so that a
short peak of overcurrent does not cause the operation of a protection even when the
overcurrent has ceased. This phenomenon is described in Figure 41.
Current (A)
Operate current
Reset current
Time (s)
IEC05000203-en-2.vsd
IEC05000203 V4 EN-US
Im ax
Ipu ³ 1.2 ×
k
EQUATION1262 V2 EN-US (Equation 23)
where:
1.2 is a safety factor
k is the reset ratio of the protection
Imax is the maximum load current
The load current up to the present situation can be found from operation statistics. The
current setting must remain valid for several years. In most cases, the setting values are
updated once every five years or less often. Investigate the maximum load current that the
equipment on the line can withstand. Study components, such as line conductors, current
transformers, circuit breakers, and disconnectors. The manufacturer of the equipment
normally gives the maximum thermal load current of the equipment.
The maximum load current on the line has to be estimated. There is also a demand that all
faults within the zone that the protection shall cover must be detected by the phase
overcurrent protection. The minimum fault current Iscmin to be detected by the protection
must be calculated. Taking this value as a base, the highest pickup current setting can be
written according to Equation 24.
where:
0.7 is a safety factor
Iscmin is the smallest fault current to be detected by the overcurrent protection.
As a summary, the operating current shall be chosen within the interval stated in Equation 25.
Im ax
1.2 × £ Ipu £ 0.7 × Isc min
k
EQUATION1264 V2 EN-US (Equation 25)
The high current function of the overcurrent protection, which only has a short-delay trip time,
must be given a current setting so that the protection is selective to other protection
functions in the power system. It is desirable to have rapid tripping of faults within a large part
of the power system to be protected by the protection (primary protected zone). A fault
current calculation gives the largest current of faults, Iscmax, at the most remote part of the
primary protected zone. The risk of transient overreach must be considered, due to a possible
DC component of the short circuit current. The lowest current setting of the fastest stage can
be written according to
where:
1.2 is a safety factor
kt is a factor that takes care of the transient overreach due to the DC component of the fault current
and can be considered to be less than 1.05
Iscmax is the largest fault current at a fault at the most remote point of the primary protection zone.
The operate time of the phase overcurrent protection has to be chosen so that the fault time
is short enough that the protected equipment will not be destroyed due to thermal overload
while, at the same time, selectivity is assured. For overcurrent protection in a radial fed
network, the time setting can be chosen in a graphical way. This is mostly used in the case of
inverse time overcurrent protection. Figure 42 shows how the time-versus-current curves are
plotted in a diagram. The time setting is chosen to get the shortest fault time with maintained
selectivity. Selectivity is assured if the time difference between the curves is larger than a
critical time difference.
Time-current curves
10
tfunc1n
Trip time
tfunc2n
0.01
10 Strn 10000
Fault Current
en05000204.ai
IEC05000204 V2 EN-US
To assure selectivity between different protection functions in the radial network, there has to
be a minimum time difference Dt between the time delays of two protections. To determine
the shortest possible time difference, the operation time of the protection, the breaker
opening time and the protection resetting time must be known. These time delays can vary
significantly between different protective equipment. The following time delays can be
estimated:
A1 B1
Feeder
Fault
I> I>
Time axis
where:
t=0 is when the fault occurs
t=t1 is when protection IED B1 and protection IED A1 start
t=t2 is when the trip signal from the overcurrent protection at IED B1 is sent to the circuit breaker.
t=t3 is when the circuit breaker at IED B1 opens. The circuit breaker opening time is t3 - t2
t=t4 is when the overcurrent protection at IED A1 resets. The protection resetting time is t4 - t3.
To ensure that the overcurrent protection at IED A1 is selective to the overcurrent protection
at IED B1, the minimum time difference must be larger than the time t3. There are uncertainties
in the values of protection operation time, breaker opening time and protection resetting
time. Therefore a safety margin has to be included. With normal values the needed time
difference can be calculated according to Equation 27.
Dt ³ 40 ms + 100 ms + 40 ms + 40 ms = 220 ms
EQUATION1266 V1 EN-US (Equation 27)
7.2.1 Identification
M14881-1 v6
The directional residual overcurrent protection, four steps EF4PTOC is used in several
applications in the power system. Some applications are:
In many applications, several steps with different current operating levels and time delays are
needed. EF4PTOC can have up to four, individual settable steps. The flexibility of each step of
EF4PTOC is great. The following options are possible:
where currents in transformer neutrals providing the neutral source (ZN) is used to polarize (IN
· ZN) the function. Dual polarizing, where the sum of both voltage and current components is
allowed to polarize can also be selected.
Choice of time characteristics: There are several types of time characteristics available such as
definite time delay and different types of inverse time characteristics. The selectivity between
different overcurrent protections is normally enabled by co-ordination between the operate
time of the different protections. To enable optimal co-ordination all overcurrent protections,
to be co-ordinated against each other, should have the same time characteristic. Therefore a
wide range of standardized inverse time characteristics are available for IEC and ANSI.
Normally it is required that EF4PTOC shall reset as fast as possible when the current level gets
lower than the operation level. In some cases some sort of delayed reset is required. Therefore
different kinds of reset characteristics can be used.
For some protection applications, there can be a need to change the current operating level
for some time. Therefore, there is a possibility to give a setting of a multiplication factor
INxMult to the residual current pick-up level. This multiplication factor is activated from a
binary input signal ENMULTx to the function.
Power transformers can have a large inrush current, when being energized. This inrush current
can produce residual current component. The phenomenon is due to saturation of the
transformer magnetic core during parts of the cycle. There is a risk that inrush current will give
a residual current that reaches level above the operating current of the residual overcurrent
protection. The inrush current has a large second harmonic content. This can be used to avoid
unwanted operation of the protection. Therefore, EF4PTOC has a possibility of second
harmonic restrain if the level of 2nd harmonic current reaches a value above a set percent of the
fundamental current.
M15282-3 v12
The parameters for the four step residual overcurrent protection are set via the local HMI or
PCM600. The following settings can be done for the function.
Common base IED values for the primary current (IBase), primary voltage (UBase) and primary
power (SBase) are set in global base values for settings function GBASVAL.
GlobalBaseSel: Selects the global base value group used by the function to define IBase, UBase
and SBase.
SeqTypeUPol: This is used to select the type of voltage polarising quantity i.e. Zero seq or Neg
seq for direction detection.
SeqTypeIPol: This is used to select the type of current polarising quantity i.e. Zero seq or Neg
seq for direction detection.
SeqTypeIDir: This is used to select the type of operating current quantity i.e. Zero seq or Neg
seq for direction detection.
AngleRCA: Relay characteristic angle given in degree. This angle is defined as shown in
Figure 44. The angle is defined positive when the residual current lags the reference voltage
(Upol = 3U0 or U2)
Operation
IN>Dir
IEC05000135-5-en.vsdx
IEC05000135 V5 EN-US
Normally voltage polarizing from the internally calculated residual sum or an external open
delta is used.
Current polarizing is useful when the local source is strong and a high sensitivity is required. In
such cases the polarizing voltage (3U0) can be below 1% and it is then necessary to use current
polarizing or dual polarizing. Multiply the required set current (primary) with the minimum
impedance (ZNpol) and check that the percentage of the phase-to-earth voltage is definitely
higher than 1% (minimum 3U0>UPolMin setting) as a verification.
RNPol, XNPol: The zero-sequence source is set in primary ohms as base for the current
polarizing. The polarizing voltage is then achieved as 3I0 · ZNpol. The ZNpol can be defined as
(ZS1-ZS0)/3, that is the earth return impedance of the source behind the protection. The
maximum earth-fault current at the local source can be used to calculate the value of ZN as
U/(√3 · 3I0) Typically, the minimum ZNPol (3 · zero sequence source) is set. The setting is in
primary ohms.
When the dual polarizing method is used, it is important that the setting INx> or the product
3I0 · ZNpol is not greater than 3U0. If so, there is a risk for incorrect operation for faults in the
reverse direction.
IPolMin: is the minimum earth-fault current accepted for directional evaluation. For smaller
currents than this value, the operation will be blocked. A typical setting is 5-10% of IB.
UPolMin: Minimum polarization (reference) polarizing voltage for the directional function,
given in % of UBase/√3.
IN>Dir: Operate residual current release level in % of IB for directional comparison scheme. The
setting is given in % of IB and must be set below the lowest INx> setting, set for the
directional measurement. The output signals, STFW and STRV can be used in a teleprotection
scheme. The appropriate signal should be configured to the communication scheme block.
If a power transformer is energized there is a risk that the current transformer core will
saturate during part of the period, resulting in a transformer inrush current. This will give a
declining residual current in the network, as the inrush current is deviating between the
phases. There is a risk that the residual overcurrent function will give an unwanted trip. The
inrush current has a relatively large ratio of 2nd harmonic component. This component can be
used to create a restrain signal to prevent this unwanted function.
At current transformer saturation a false residual current can be measured by the protection.
Here the 2nd harmonic restrain can prevent unwanted operation as well.
2ndHarmStab: The rate of 2nd harmonic current content for activation of the 2nd harmonic
restrain signal. The setting is given in % of the fundamental frequency residual current.
In case of parallel transformers there is a risk of sympathetic inrush current. If one of the
transformers is in operation, and the parallel transformer is switched in, the asymmetric
inrush current of the switched-in transformer will cause partial saturation of the transformer
already in service. This is called transferred saturation. The 2nd harmonic of the inrush currents
of the two transformers will be in phase opposition. The summation of the two currents will
thus give a small 2nd harmonic current. The residual fundamental current will however be
significant. The inrush current of the transformer in service before the parallel transformer
energizing, will be a little delayed compared to the first transformer. Therefore, we will have
high 2nd harmonic current initially. After a short period this current will however be small and
the normal 2nd harmonic blocking will reset.
IN> IN>
Power System
en05000136.vsd
IEC05000136 V1 EN-US
The settings for the parallel transformer logic are described below.
UseStartValue: Gives which current level should be used for the activation of the blocking
signal. This is given as one of the settings of the steps: Step 1/2/3/4. Normally, the step
having the lowest operation current level should be set.
In case of energizing a faulty object there is a risk of having a long fault clearance time, if the
fault current is too small to give fast operation of the protection. The switch on to fault
function can be activated from auxiliary signals from the circuit breaker, either the close
command or the open/close position (change of position).
This logic can be used to issue a fast trip if one breaker pole does not close properly at a
manual or automatic closing.
SOTF and under time are similar functions to achieve fast clearance at asymmetrical closing
based on requirements from different utilities.
The function is divided into two parts. The SOTF function will give operation from step 2 or 3
during a set time after change in the position of the circuit breaker. The SOTF function has a
set time delay. The under time function, which has 2nd harmonic restrain blocking, will give
operation from step 4. The 2nd harmonic restrain will prevent unwanted function in case of
transformer inrush current. The under time function has a set time delay.
ActivationSOTF: This setting will select the signal to activate SOTF function; CB position
open/CB position closed/CB close command.
StepForSOTF: If this parameter is set on step 3, the step 3 start signal will be used as current
set level. If set on step 2, the step 2 start signal will be used as current set level.
tSOTF: Time delay for operation of the SOTF function. The setting range is 0.000 - 60.000 s in
step of 0.001 s. The default setting is 0.100 s
t4U: Time interval when the SOTF function is active after breaker closing. The setting range is
0.000 - 60.000 s in step of 0.001 s. The default setting is 1.000 s.
ActUnderTime: Describes the mode to activate the sensitive undertime function. The function
can be activated by Circuit breaker position (change) or Circuit breaker command.
tUnderTime: Time delay for operation of the sensitive undertime function. The setting range is
0.000 - 60.000 s in step of 0.001 s. The default setting is 0.300 s
Characteristx: Selection of time characteristic for step x. Definite time delay and different
types of inverse time characteristics are available.
Inverse time characteristic enables fast fault clearance of high current faults at the same time
as selectivity to other inverse time phase overcurrent protections can be assured. This is
mainly used in radial fed networks but can also be used in meshed networks. In meshed
networks, the settings must be based on network fault calculations.
To assure selectivity between different protections, in the radial network, there has to be a
minimum time difference Dt between the time delays of two protections. To determine the
shortest possible time difference, the operation time of protections, breaker opening time
and protection resetting time must be known. These time delays can vary significantly
between different protective equipment. The following time delays can be estimated:
tx: Definite time delay for step x. The definite time tx is added to the inverse time when inverse
time characteristic is selected. Note that the value set is the time between activation of the
start and the trip outputs.
INx>Max and INx>Min should only be changed if remote setting of operation current level,
INx>, is used. The limits are used for decreasing the used range of the INx> setting. If INx> is
set outside INx>Max and INx>Min, the closest of the limits to INx> is used by the function. If
INx>Max is smaller than INx>Min, the limits are swapped.
kx: Time multiplier for the dependent (inverse) characteristic for step x.
IMinx: Minimum operate current for step x in % of IB. Set IMinx below INx> for every step to
achieve ANSI reset characteristic according to standard. If IMinx is set above INx> for any step,
signal will reset at current equals to zero.
txMin: Minimum operating time for inverse time characteristics. At high currents, the inverse
time characteristic might give a very short operation time. By setting this parameter, the
operation time of the step can never be shorter than the setting.
Operate time
tx
txMin
IMinx Current
IEC10000058
IEC10000058 V2 EN-US
Figure 46: Minimum operate current and operate time for inverse time characteristics
In order to fully comply with the curves definition, the setting parameter txMin shall be set to
the value which is equal to the operate time of the selected IEC inverse curve for measured
current of twenty times the set current pickup value. Note that the operate time value is
dependent on the selected setting value for time multiplier kx.
INxMult: Multiplier for scaling of the current setting value. If a binary input signal (ENMULTx) is
activated, the current operation level is increased by this setting constant.
ResetTypeCrvx: The reset of the delay timer can be made in different ways. The possibilities
are described in the technical reference manual.
HarmBlockx: This is used to enable block of step x from 2nd harmonic restrain function.
tPCrvx, tACrvx, tBCrvx, tCCrvx: Parameters for user programmable of inverse time
characteristic curve. The time characteristic equation is according to equation 28:
æ ö
ç A
÷
t[ s ] = ç + B ÷×k
ç æ i öp ÷
çç ÷ -C ÷
è è in > ø ø
EQUATION1189 V1 EN-US (Equation 28)
tPRCrvx, tTRCrvx, tCRCrvx: Parameters for user programmable of inverse reset time
characteristic curve. Further description can be found in the technical reference manual.
7.3.1 Identification
GUID-E1720ADA-7F80-4F2C-82A1-EF2C9EF6A4B4 v1
Four step negative sequence overcurrent protection NS4PTOC is used in several applications
in the power system. Some applications are:
In many applications several steps with different current operating levels and time delays are
needed. NS4PTOC can have up to four, individual settable steps. The flexibility of each step of
NS4PTOC function is great. The following options are possible:
Choice of time characteristics: There are several types of time characteristics available such as
definite time delay and different types of inverse time characteristics. The selectivity between
different overcurrent protections is normally enabled by co-ordination between the operating
time of the different protections. To enable optimal co-ordination all overcurrent relays, to be
co-ordinated against each other, should have the same time characteristic. Therefore a wide
range of standardized inverse time characteristics are available: IEC and ANSI.
Normally it is required that the negative sequence overcurrent function shall reset as fast as
possible when the current level gets lower than the operation level. In some cases some sort of
delayed reset is required. Therefore different kinds of reset characteristics can be used.
For some protection applications there can be a need to change the current operating level for
some time. Therefore there is a possibility to give a setting of a multiplication factor IxMult to
the negative sequence current pick-up level. This multiplication factor is activated from a
binary input signal ENMULTx to the function.
The parameters for Four step negative sequence overcurrent protection NS4PTOC are set via
the local HMI or Protection and Control Manager (PCM600).
The following settings can be done for the four step negative sequence overcurrent
protection:
Common base IED values for the primary current (IBase), primary voltage (UBase) and primary
power (SBase) are set in global base values for settings function GBASVAL.
GlobalBaseSel: Selects the global base value group used by the function to define IBase, UBase
and SBase.
GUID-F7AA2194-4D1C-4475-8853-C7D064912614 v4
Characteristx: Selection of time characteristic for step x. Definite time delay and different
types of inverse time characteristics are available.
The different characteristics are described in the Technical Reference Manual (TRM).
Ix>: Operation negative sequence current level for step x given in % of IBase.
tx: Definite time delay for step x. The definite time tx is added to the inverse time when inverse
time characteristic is selected. Note that the value set is the time between activation of the
start and the trip outputs.
IMinx: Minimum operate current for step x in % of IBase. Set IMinx below Ix> for every step to
achieve ANSI reset characteristic according to standard. If IMinx is set above Ix> for any step
the ANSI reset works as if current is zero when current drops below IMinx.
IxMult: Multiplier for scaling of the current setting value. If a binary input signal (ENMULTx) is
activated the current operation level is multiplied by this setting constant.
txMin: Minimum operation time for inverse time characteristics. At high currents the inverse
time characteristic might give a very short operation time. By setting this parameter the
operation time of the step can never be shorter than the setting.
Operate time
tx
txMin
IMinx Current
IEC10000058
IEC10000058 V2 EN-US
Figure 47: Minimum operate current and operation time for inverse time characteristics
ResetTypeCrvx: The reset of the delay timer can be made in different ways. By choosing
setting there are the following possibilities:
Curve name
Instantaneous
IEC Reset (constant time)
ANSI Reset (inverse time)
The different reset characteristics are described in the Technical Reference Manual (TRM).
There are some restrictions regarding the choice of reset delay.
For the independent time delay characteristics the possible delay time settings are
instantaneous (1) and IEC (2 = set constant time reset).
For ANSI inverse time delay characteristics all three types of reset time characteristics are
available; instantaneous (1), IEC (2 = set constant time reset) and ANSI (3 = current dependent
reset time).
For IEC inverse time delay characteristics the possible delay time settings are instantaneous
(1) and IEC (2 = set constant time reset).
For the programmable inverse time delay characteristics all three types of reset time
characteristics are available; instantaneous (1), IEC (2 = set constant time reset) and ANSI (3 =
current dependent reset time). If the current dependent type is used settings pr, tr and cr
must be given.
tPCrvx, tACrvx, tBCrvx, tCCrvx: Parameters for programmable inverse time characteristic
curve. The time characteristic equation is according to equation 29:
æ ö
ç A
÷
t[ s ] = ç + B÷×k
ç æ i öp ÷
çç ÷ -C ÷
è è in > ø ø
EQUATION1189 V1 EN-US (Equation 29)
tPRCrvx, tTRCrvx, tCRCrvx: Parameters for customer creation of inverse reset time
characteristic curve. Further description can be found in the Technical Reference Manual.
AngleRCA: Relay characteristic angle given in degrees. This angle is defined as shown in
figure 48. The angle is defined positive when the residual current lags the reference voltage
(Upol = -U2)
Reverse
Area
AngleRCA Upol=-U2
Forward
Area
Iop = I2
IEC10000031-1-en.vsd
IEC10000031 V1 EN-US
I>Dir: Operate residual current level for directional comparison scheme. The setting is given in
% of IBase. The start forward or start reverse signals can be used in a communication scheme.
The appropriate signal must be configured to the communication scheme block.
7.4.1 Identification
M14877-1 v2
SYMBOL-A V1 EN-US
Transformers in the power system are designed for a certain maximum load current (power)
level. If the current exceeds this level the losses will be higher than expected. As a consequence
the temperature of the transformer will increase. If the temperature of the transformer
reaches too high a value, the equipment might be damaged;
In stressed situations in the power system it can be required to overload transformers for a
limited time. This should be done without the above mentioned risks. The thermal overload
protection provides information and makes temporary overloading of transformers possible.
The permissible load level of a power transformer is highly dependent on the cooling system
of the transformer. There are two main principles:
• OA: The air is naturally circulated to the coolers without fans and the oil is naturally
circulated without pumps.
• FOA: The coolers have fans to force air for cooling and pumps to force the circulation of
the transformer oil.
The protection can have two sets of parameters, one for non-forced cooling and one for forced
cooling. Both the permissive steady state loading level as well as the thermal time constant is
influenced by the cooling system of the transformer. The two parameters sets can be
activated by the binary input signal COOLING. This can be used for transformers where forced
cooling can be taken out of operation, for example at fan or pump faults.
The thermal overload protection estimates the internal heat content of the transformer
(temperature) continuously. This estimation is made by using a thermal model of the
transformer which is based on current measurement.
If the heat content of the protected transformer reaches a set alarm level a signal can be given
to the operator. Two alarm levels are available. This enables preventive actions in the power
system to be taken before dangerous temperatures are reached. If the temperature continues
to increase to the trip value, the protection initiates a trip of the protected transformer.
After tripping by the thermal overload protection, the transformer will cool down over time.
There will be a time gap before the heat content (temperature) reaches such a level so that the
transformer can be taken into service again. Therefore, the function will continue to estimate
the heat content using a set cooling time constant. Energizing of the transformer can be
blocked until the heat content has reached a set level.
The parameters for the thermal overload protection, two time constants (TRPTTR) are set via
the local HMI or Protection and Control IED Manager (PCM600).
The following settings can be done for the thermal overload protection:
Operation: Off/On
Operation: Sets the mode of operation. Off switches off the complete function.
GlobalBaseSel: Selects the global base value group used by the function to define IBase, UBase
and SBase.
IRef: Reference level of the current given in %. When the current is equal to IRef the final
(steady state) heat content is equal to 1. It is suggested to give a setting corresponding to the
rated current of the transformer winding.
IRefMult: If a binary input ENMULT is activated the reference current value can be multiplied by
the factor IRefMult. The activation could be used in case of deviating ambient temperature
from the reference value. In the standard for loading of a transformer an ambient temperature
of 20°C is used. For lower ambient temperatures the load ability is increased and vice versa.
IRefMult can be set within a range: 0.01 - 10.00.
IBase1: Base current for setting given as percentage of IBase. This setting shall be related to
the status with no COOLING input. It is suggested to give a setting corresponding to the rated
current of the transformer with natural cooling (OA).
IBase2: Base current for setting given as percentage of IBase. This setting shall be related to
the status with activated COOLING input. It is suggested to give a setting corresponding to
the rated current of the transformer with forced cooling (FOA). If the transformer has no
forced cooling IBase2 can be set equal to IBase1.
Tau1: The thermal time constant of the protected transformer, related to IBase1 (no cooling)
given in minutes.
Tau2: The thermal time constant of the protected transformer, related to IBase2 (with cooling)
given in minutes.
The thermal time constant should be obtained from the transformer manufacturers manuals.
The thermal time constant is dependent on the cooling and the amount of oil. Normal time
constants for medium and large transformers (according to IEC 60076-7) are about 2.5 hours
for naturally cooled transformers and 1.5 hours for forced cooled transformers.
The time constant can be estimated from measurements of the oil temperature during a
cooling sequence (described in IEC 60076-7). It is assumed that the transformer is operated at
a certain load level with a constant oil temperature (steady state operation). The oil
temperature above the ambient temperature is DQo0. Then the transformer is disconnected
from the grid (no load). After a time t of at least 30 minutes the temperature of the oil is
measured again. Now the oil temperature above the ambient temperature is DQot. The thermal
time constant can now be estimated as:
t
t=
ln DQo 0 - ln DQ ot
EQUATION1180 V1 EN-US (Equation 30)
If the transformer has forced cooling (FOA) the measurement should be made both with and
without the forced cooling in operation, giving Tau2 and Tau1.
The time constants can be changed if the current is higher than a set value or lower than a set
value. If the current is high it is assumed that the forced cooling is activated while it is
deactivated at low current. The setting of the parameters below enables automatic
adjustment of the time constant.
Tau1High: Multiplication factor to adjust the time constant Tau1 if the current is higher than
the set value IHighTau1. IHighTau1 is set in % of IBase1.
Tau1Low: Multiplication factor to adjust the time constant Tau1 if the current is lower than the
set value ILowTau1. ILowTau1 is set in % of IBase1.
Tau2High: Multiplication factor to adjust the time constant Tau2 if the current is higher than
the set value IHighTau2. IHighTau2 is set in % of IBase2.
Tau2Low: Multiplication factor to adjust the time constant Tau2 if the current is lower than the
set value ILowTau2. ILowTau2 is set in % of IBase2.
The possibility to change time constant with the current value as the base can be useful in
different applications. Below some examples are given:
• In case a total interruption (low current) of the protected transformer all cooling
possibilities will be inactive. This can result in a changed value of the time constant.
• If other components (motors) are included in the thermal protection, there is a risk of
overheating of that equipment in case of very high current. The thermal time constant is
often smaller for a motor than for the transformer.
ITrip: The steady state current that the transformer can withstand. The setting is given in % of
IBase1 or IBase2.
Alarm1: Heat content level for activation of the signal ALARM1. ALARM1 is set in % of the trip
heat content level.
Alarm2: Heat content level for activation of the output signal ALARM2. ALARM2 is set in % of
the trip heat content level.
ResLo: Lockout release level of heat content to release the lockout signal. When the thermal
overload protection trips a lock-out signal is activated. This signal is intended to block
switching on of the protected circuit transformer as long as the transformer temperature is
high. The signal is released when the estimated heat content is below the set value. This
temperature value should be chosen below the alarm temperature. ResLo is set in % of the trip
heat content level.
ThetaInit: Heat content before activation of the function. This setting can be set a little below
the alarm level. If the transformer is loaded before the activation of the protection function, its
temperature can be higher than the ambient temperature. The start point given in the setting
will prevent risk of no trip at overtemperature during the first moments after activation.
ThetaInit: is set in % of the trip heat content level.
Warning: If the calculated time to trip factor is below the setting Warning a warning signal is
activated. The setting is given in minutes.
Calculation of the operate time with the available current is performed only if the calculated
final temperature is greater than the operate level temperature.
æQ - Qoperate ö
toperate = -t × ln ç final
ç Q final - Q n ÷÷
è ø
EQUATION1176 V1 EN-US (Equation 31)
where:
toperate is the time to operate
2
I is the steady state heat content
final
I ref
Consider that the given system has IBase of 1000 A and the cooling system is ON. The
following settings are used to calculate the operate time:
IRef 110%
IBase1 110% of IB
IBase2 120% of IB
Tau1 150 min
Tau2 90 min
IHighTau1 110% of IB1
Tau1High 125% of tC1
ILowTau1 90% of IB1
Tau1Low 75% of tC1
IHighTau2 110% of IB2
Tau2High 115% of tC2
ILowTau2 90% of IB2
Tau2Low 85% of tC2
As the cooling system is ON, IBase2 is selected as the base current and Tau2 setting is selected
as the time constant.
For example, the largest phase load current is taken as 1800 A, then:
2
1800
final 2677685.95
1.1
After the trip, a lockout is released to inhibit reconnecting the tripped circuit. The output
lockout signal LOCKOUT is activated when the temperature of the object is greater than the
set lockout release temperature setting ResLo.
æQ - Qlockout _ release ö
tlockout _ release = -t × ln ç final ÷÷
ç Q final - Q n
è ø
EQUATION1177 V1 EN-US (Equation 32)
where:
tlockout_release is the time to lockout release
Consider that the current heat content θn is 2700000 and the cooling system is still ON, then:
7.5.1 Identification
M14878-1 v5
SYMBOL-U V1 EN-US
In the design of the fault clearance system the N-1 criterion is often used. This means that a
fault needs to be cleared even if any component in the fault clearance system is faulty. One
necessary component in the fault clearance system is the circuit breaker.
It is from practical and economical reason not feasible to duplicate the circuit breaker for the
protected object. Instead a breaker failure protection is used.
Breaker failure protection CCRBRF will issue a backup trip command to adjacent circuit
breakers in case of failure to trip of the “normal” circuit breaker for the protected object. The
detection of failure to break the current through the breaker is made either by means of
current measurement or as detection of closed status using auxiliary contact.
CCRBRF can also give a retrip command. This means that a second trip signal is sent to the
protected object circuit breaker. The retrip function can be used to increase the probability of
operation of the breaker, or it can be used to avoid backup trip of many breakers in case of
mistakes during relay maintenance and testing.
The parameters for Breaker failure protection CCRBRF are set via the local HMI or PCM600.
The following settings can be done for the breaker failure protection.
GlobalBaseSel: Selects the global base value group used by the function to define IBase, UBase
and SBase.
FunctionMode: This parameter can be set Current or Contact. This states the way the
detection of failure of the breaker is performed. In the mode current the current measurement
is used for the detection. In the mode Contact the long duration of breaker position signal is
used as indicator of failure of the breaker. The mode Current/Contact means that both ways
of detections are activated. Contact mode can be usable in applications where the fault
current through the circuit breaker is small. This can be the case for some generator
protection application (for example reverse power protection) or in case of line ends with
weak end infeed.
RetripMode: This setting states how the retrip function shall operate. Retrip Off means that
the retrip function is not activated. CB Pos Check (circuit breaker position check) and Current
means that a phase current must be larger than the operate level to allow retrip. CB Pos Check
(circuit breaker position check) and Contact means retrip is done when circuit breaker is
closed (breaker position is used). No CBPos Check means retrip is done without any check of
breaker position.
BuTripMode: backup trip mode is given to state sufficient current criteria to detect failure to
break. For Current operation 2 out of 4 means that at least two currents, of the three-phase
currents and the residual current, shall be high to indicate breaker failure. 1 out of 3 means
that at least one current of the three-phase currents shall be high to indicate breaker failure. 1
out of 4 means that at least one current of the three-phase currents or the residual current
shall be high to indicate breaker failure. In most applications 1 out of 3 is sufficient. For
Contact operation means backup trip is done when circuit breaker is closed (breaker position
is used).
IP>: Current level for detection of breaker failure, set in % of IBase. This parameter should be
set so that faults with small fault current can be detected. The setting can be chosen in
accordance with the most sensitive protection function to start the breaker failure protection.
Default setting is 10% of IBase.
I>BlkCont: If any contact based detection of breaker failure is used, this function can be
blocked if any phase current is larger than this setting level. If the FunctionMode is set
Current/Contact breaker failure for high current faults are safely detected by the current
measurement function. To increase security the contact based function should be disabled for
high currents. The setting can be given within the range 5 – 200% of IBase.
IN>: Residual current level for detection of breaker failure set in % of IBase. In high impedance
earthed systems the residual current at phase- to-earth faults are normally much smaller than
the short circuit currents. In order to detect breaker failure at single phase-to-earth faults in
such systems it is necessary to measure the residual current separately. Also in effectively
earthed systems the setting of the earth-fault current protection can be chosen to relatively
low current level. The BuTripMode shall be set 1 out of 4 in such systems The current setting
should be chosen in accordance to the setting of the sensitive earth-fault protection. The
setting can be given within the range 2 – 200 % of IBase.
t1: Time delay of the retrip. The setting can be given within the range 0 – 60s in steps of 0.001
s. Typical setting is within range 0 – 50ms.
t2: Time delay of the backup trip. The choice of this setting is made as short as possible at the
same time as unwanted operation must be avoided. Typical setting is within range 90 – 200ms
(also dependent of retrip timer).
Timer t2 is used when function is started in one phase only (i.e. for single-phase to ground
fault on an OHL (Over Head Lines) when single-pole auto-reclosing is used).
The minimum time delay for the backup trip can be estimated as:
where:
tCB_open is the maximum opening time for the circuit breaker
tBFP_reset is the maximum time for breaker failure protection to detect correct breaker function
(the current criteria reset)
tmargin is a safety margin
It is often required that the total fault clearance time shall be less than a given critical time.
This time is often dependent of the ability of the power system to maintain transient stability
in case of a fault close to a power plant.
Protection
operate time
Normal tcbopen
Time
Note that for a protected object which are always tripped three-phase (e.g. transformers,
generators, reactors, cables, etc.) this timer shall always be set to the same value as t2 timer.
t3: Additional time delay to t2 for a second backup trip TRBU2. In some applications there
might be a requirement to have separated backup trip functions, tripping different backup
circuit breakers.
tCBAlarm: Time delay for alarm in case of indication of faulty circuit breaker. There is a binary
input CBFLT from the circuit breaker. This signal is activated when internal supervision in the
circuit breaker detect that the circuit breaker is unable to clear fault. This could be the case
when gas pressure is low in a SF6 circuit breaker, of others. After the set time an alarm is
given, so that actions can be done to repair the circuit breaker. Note that the time delay for
backup trip t2 is bypassed when the CBFLT is active. Typical setting is 2.0 seconds..
tPulse: Trip pulse duration. This setting must be larger than the opening time of circuit
breakers to be tripped from the breaker failure protection. Typical setting is 200 ms.
GUID-845257FF-2774-472A-B982-E9DDD8966988 v1
Table 18: Setting summary for FunctionMode, StartMode, RetripMode and BuTripMode
No. StartMode RetripMode t1 and t2 initiated When t1 has When t2 or t2MPh t1 and t2 and t2MPh
with elapsed, TRRET will has elapsed, TRBU will be stopped
will be given if (reset) if
FunctionMode = Current
1 LatchedStart Off external START never be given current is above t1 and (t2 or
set level *) t2MPh) and 150ms
expires and
current is below
set level *)
2 LatchedStart UseFunction external START be given if current current is above t1 and (t2 or
Mode is above set level set level *) t2MPh) and 150ms
of IPh> expires and
current is below
set level *)
3 LatchedStart Always external START always be given current is above t1 and (t2 or
set level *) t2MPh) and 150ms
expires and
current is below
set level *)
4 FollowStart Off external START never be given current is above external START
set level *) disappears
5 FollowStart UseFunction external START be given if current current is above external START
Mode is above set level set level *) disappears
of IPh>
6 FollowStart Always external START be given if external current is above external START
START is present set level *) disappears
7 FollowStart& Off external START never be given current is above current is below
Mode and current set level *) and set level *) or
above set level external START external START
present disappears
8 FollowStart& UseFunction external START be given if current current is above current is below
Mode Mode and current is above set level set level *) and set level *) or
above set level of IPh> and external START external START
external START is present disappears
present
9 FollowStart& Always external START be given if external current is above current is below
Mode and current START is present set level *) and set level *) or
above set level external START external START
present disappears
*) Set level depends on selected BuTripMode, that is, set level can be either IPh> or IN> or both.
No. StartMode RetripMode t1 and t2 initiated When t1 has When t2 or t2MPh t1 and t2 and
with elapsed, TRRET will has elapsed, TRBU t2MPh will be
will be given if stopped (reset) if
FunctionMode = CB Pos
10 LatchedStart Off external START never be given CBCLDLx input has t1 and (t2 or
logical value one t2MPh) and 150ms
expires and
CBCLDLx input
has logical value
zero
11 LatchedStart UseFunction external START be given if CBCLDLx input has t1 and (t2 or
Mode CBCLDLx input has logical value one t2MPh) and 150ms
logical value one expires and
CBCLDLx input
has logical value
zero
12 LatchedStart Always external START always be given CBCLDLx input has t1 and (t2 or
logical value one t2MPh) and 150ms
expires and
CBCLDLx input
has logical value
zero
13 FollowStart Off external START never be given CBCLDLx input has external START
logical value one disappears
14 FollowStart UseFunction external START be given if CBCLDLx input has external START
Mode CBCLDLx input has logical value one disappears
logical value one
15 FollowStart Always external START if external START is CBCLDLx input has external START
present logical value one disappears
16 FollowStart& Off external START never be given be given if CBCLDLx input
Mode and CBCLDLx CBCLDLx input has has logical value
input has logical logical value one zero or external
value one and external START disappears
START is present
17 FollowStart& UseFunction external START be given if be given if CBCLDLx input
Mode Mode and CBCLDLx CBCLDLx input has CBCLDLx input has has logical value
input has logical logical value one logical value one zero or external
value one and external and external START disappears
START is present START is present
18 FollowStart& Always external START be given if external be given if CBCLDLx input
Mode and CBCLDLx START is present CBCLDLx input has has logical value
input has logical logical value one zero or external
value one and external START disappears
START is present
No. StartMode RetripMode t1 and t2 initiated When t1 has When t2 or t2MPh t1 and t2 and
with elapsed, TRRET will has elapsed, TRBU t2MPh will be
will be given if stopped (reset) if
FunctionMode = Current or CB Pos
19 LatchedStart Off external START never be given current is above t1 and (t2 or
set level *) and t2MPh) and 150ms
higher than expires and
I>BlkCBPos or current is below
CBCLDLx input set level *) or
has logical value CBCLDLx input
one when current has logical value
is smaller than zero
I>BlkCBPos
20 LatchedStart UseFunction external START be given if current current is above t1 and (t2 or
Mode is above set level set level *) and t2MPh) and 150ms
of IPh> and higher higher than expires and
than I>BlkCBPos or I>BlkCBPos or current is below
CBCLDLx input has CBCLDLx input set level *) or
logical value one has logical value CBCLDLx input
when current is one when current has logical value
smaller than is smaller than zero
I>BlkCBPos I>BlkCBPos
21 LatchedStart Always external START always be given current is above t1 and (t2 or
set level *) and t2MPh) and 150ms
higher than expires and
I>BlkCBPos or current is below
CBCLDLx input set level *) or
has logical value CBCLDLx input
one when current has logical value
is smaller than zero
I>BlkCBPos
22 FollowStart Off external START never be given current is above external START
set level *) and disappears
higher than
I>BlkCBPos or
CBCLDLx input
has logical value
one when current
is smaller than
I>BlkCBPos
23 FollowStart UseFunction external START be given if current current is above external START
Mode is above set level set level *) and disappears
of IPh> and higher higher than
than I>BlkCBPos or I>BlkCBPos or
CBCLDLx input has CBCLDLx input
logical value one has logical value
when current is one when current
smaller than is smaller than
I>BlkCBPos I>BlkCBPos
24 FollowStart Always external START be given if external current is above external START
START is present set level *) and disappears
higher than
I>BlkCBPos or
CBCLDLx input
has logical value
one when current
is smaller than
I>BlkCBPos
Table continues on next page
No. StartMode RetripMode t1 and t2 initiated When t1 has When t2 or t2MPh t1 and t2 and
with elapsed, TRRET will has elapsed, TRBU t2MPh will be
will be given if stopped (reset) if
25 FollowStart& Off external START never be given current is above current is below
Mode and current above set level *) and set level *) or
set level higher than external START
I>BlkCBPos or disappears
CBCLDLx input
has logical value
one when current
is smaller than
I>BlkCBPos
26 FollowStart& UseFunction external START be given if current current is above current is below
Mode Mode and current above is above set level set level *) and set level *) or
set level of IPh> and higher higher than external START
than I>BlkCBPos or I>BlkCBPos or disappears
CBCLDLx input has CBCLDLx input
logical value one has logical value
when current is one when current
smaller than is smaller than
I>BlkCBPos I>BlkCBPos
27 FollowStart& Always external START be given if external current is above current is below
Mode and current above START is present set level *) and set level *) or
set level higher than external START
I>BlkCBPos or disappears
CBCLDLx input
has logical value
one when current
is smaller than
I>BlkCBPos
*) Set level depends on selected BuTripMode, that is, set level can be either IPh> or IN> or both.
7.6.1 Identification
M14888-1 v4
PD
SYMBOL-S V1 EN-US
There is a risk that a circuit breaker will get discordance between the poles at circuit breaker
operation: closing or opening. One pole can be open and the other two closed, or two poles
can be open and one closed. Pole discordance of a circuit breaker will cause unsymmetrical
currents in the power system. The consequence of this can be:
It is therefore important to detect situations with pole discordance of circuit breakers. When
this is detected the breaker should be tripped directly.
Pole discordance protection CCPDSC will detect situation with deviating positions of the poles
of the protected circuit breaker. The protection has two different options to make this
detection:
• By connecting the auxiliary contacts in the circuit breaker so that logic is created, a signal
can be sent to the protection, indicating pole discordance. This logic can also be realized
within the protection itself, by using opened and close signals for each circuit breaker
pole, connected to the protection.
• Each phase current through the circuit breaker is measured. If the difference between the
phase currents is larger than a CurrUnsymLevel this is an indication of pole discordance,
and the protection will operate.
The parameters for the Pole discordance protection CCPDSC are set via the local HMI or
PCM600.
The following settings can be done for the pole discordance protection.
GlobalBaseSel: Selects the global base value group used by the function to define IBase, UBase
and SBase.
Operation: Off or On
ContSel: Operation of the contact based pole discordance protection. Can be set: Off/PD
signal from CB. If PD signal from CB is chosen the logic to detect pole discordance is made in
the vicinity to the breaker auxiliary contacts and only one signal is connected to the pole
discordance function. If the Pole pos aux cont. alternative is chosen each open close signal is
connected to the IED and the logic to detect pole discordance is realized within the function
itself.
CurrSel: Operation of the current based pole discordance protection. Can be set: Off/CB oper
monitor/Continuous monitor. In the alternative CB oper monitor the function is activated only
directly in connection to breaker open or close command (during 200 ms). In the alternative
Continuous monitor function is continuously activated.
8.1.1 Identification
M16876-1 v7
3U<
V2 EN-US
SYMBOL-R-2U-GREATER-THAN
• Detect no voltage conditions, for example, before the energization of a HV line or for
automatic breaker trip in case of a blackout
• Initiate voltage correction measures, like insertion of shunt capacitor banks to
compensate for reactive load and thereby increasing the voltage
• Disconnect apparatuses, like electric motors, which will be damaged when subject to
service under low voltage conditions.
The function has a high measuring accuracy and a settable hysteresis to allow applications to
control reactive load.
In many cases, UV2PTUV is a useful function in circuits for local or remote automation
processes in the power system.
All the voltage conditions in the system where UV2PTUV performs its functions should be
considered. The same also applies to the associated equipment, its voltage and time
characteristic.
There is a very wide application area where general undervoltage functions are used. All
voltage-related settings are made as a percentage of the global base value UBase, which
normally is set to the primary rated voltage level (phase-to-phase) of the power system or the
high voltage equipment under consideration.
The trip time setting for UV2PTUV is normally not critical, since there must be enough time
available for the main protection to clear short circuits and earth faults.
Some applications and related setting guidelines for the voltage level are described in the
following sections.
The setting must be below the lowest occurring "normal" voltage and above the lowest
acceptable voltage for the equipment.
The setting must be below the lowest occurring "normal" voltage and above the highest
occurring voltage, caused by inductive or capacitive coupling, when the equipment is
disconnected.
The setting must be below the lowest occurring "normal" voltage and above the lowest
acceptable voltage, due to regulation, good practice or other agreements.
This setting is very much dependent on the power system characteristics, and thorough
studies have to be made to find the suitable levels.
The setting must be below the lowest occurring "normal" voltage and above the highest
occurring voltage during the fault conditions under consideration.
The following settings can be done for Two step undervoltage protection UV2PTUV:
ConnType: Sets whether the measurement shall be phase-to-earth fundamental value, phase-
to-phase fundamental value, phase-to-earth RMS value or phase-to-phase RMS value.
UBase (given in GlobalBaseSel): Base voltage phase-to-phase in primary kV. This voltage is
used as reference for voltage setting. UV2PTUV will operate if the voltage becomes lower than
the set percentage of UBase. This setting is used when ConnType is set to PhPh DFT or PhPh
RMS. Therefore, always set UBase as rated primary phase-to-phase voltage of the protected
object. For more information, refer to the Technical manual.
The setting parameters described below are identical for the two steps (n = 1 or 2). Therefore,
the setting parameters are described only once.
Characteristicn: This parameter gives the type of time delay to be used. The setting can be
Definite time, Inverse Curve A, Inverse Curve B, Prog. inv. curve. The selection is dependent on
the protection application.
OpModen: This parameter describes how many of the three measured voltages should be
below the set level to give operation for step n. The setting can be 1 out of 3, 2 out of 3 or 3 out
of 3. In most applications, it is sufficient that one phase voltage is low to give operation. If
UV2PTUV shall be insensitive for single phase-to-earth faults, 2 out of 3 can be chosen. In
subtransmission and transmission networks the undervoltage function is mainly a system
supervision function and 3 out of 3 is selected.
Un<: Set operate undervoltage operation value for step n, given as % of the parameter UBase.
The setting is highly dependent on the protection application. It is essential to consider the
minimum voltage at non-faulted situations. Normally, this non-faulted voltage is larger than
90% of the nominal voltage.
tn: time delay of step n, given in s. This setting is dependent on the protection application. In
many applications the protection function shall not directly trip when there is a short circuit or
earth faults in the system. The time delay must be coordinated to the other short circuit
protections.
tResetn: Reset time for step n if definite time delay is used, given in s. The default value is 25
ms.
tnMin: Minimum operation time for inverse time characteristic for step n, given in s. When
using inverse time characteristic for the undervoltage function during very low voltages can
give a short operation time. This might lead to unselective tripping. By setting t1Min longer
than the operation time for other protections, such unselective tripping can be avoided.
ResetTypeCrvn: This parameter for inverse time characteristic can be set to Instantaneous,
Frozen time, Linearly decreased. The default setting is Instantaneous.
tIResetn: Reset time for step n if inverse time delay is used, given in s. The default value is 25
ms.
kn: Time multiplier for inverse time characteristic. This parameter is used for coordination
between different inverse time delayed undervoltage protections.
ACrvn, BCrvn, CCrvn, DCrvn, PCrvn: Parameters to create a programmable under voltage
inverse time characteristic. Description of this can be found in the Technical manual.
CrvSatn: Tuning parameter that is used to compensate for the undesired discontinuity created
when the denominator in the equation for the customer programmable curve is equal to zero.
For more information, see the Technical manual.
IntBlkSeln: This parameter can be set to Off, Block of trip, Block all. In case of a low voltage the
undervoltage function can be blocked. This function can be used to prevent function when the
protected object is switched off. If the parameter is set Block of trip or Block all unwanted trip
is prevented.
IntBlkStValn: Voltage level under which the blocking is activated set in % of UBase. This setting
must be lower than the setting Un<. As switch of shall be detected the setting can be very low,
that is, about 10%.
tBlkUVn: Time delay to block the undervoltage step n when the voltage level is below
IntBlkStValn, given in s. It is important that this delay is shorter than the operate time delay of
the undervoltage protection step.
8.2.1 Identification
M17002-1 v8
3U>
SYMBOL-C-2U-SMALLER-THAN V2 EN-US
Two step overvoltage protection OV2PTOV is applicable in all situations, where reliable
detection of high voltage is necessary. OV2PTOV is used for supervision and detection of
abnormal conditions, which, in combination with other protection functions, increase the
security of a complete protection system.
High overvoltage conditions are caused by abnormal situations in the power system. OV2PTOV
is applied to power system elements, such as generators, transformers, motors and power
lines in order to detect high voltage conditions. OV2PTOV is used in combination with low
current signals, to identify a transmission line, open in the remote end. In addition to that,
OV2PTOV is also used to initiate voltage correction measures, like insertion of shunt reactors,
to compensate for low load, and thereby decreasing the voltage. The function has a high
measuring accuracy and hysteresis setting to allow applications to control reactive load.
OV2PTOV is used to disconnect apparatuses, like electric motors, which will be damaged when
subject to service under high voltage conditions. It deals with high voltage conditions at
power system frequency, which can be caused by:
1. Different kinds of faults, where a too high voltage appears in a certain power system, like
metallic connection to a higher voltage level (broken conductor falling down to a crossing
overhead line, transformer flash over fault from the high voltage winding to the low
voltage winding and so on).
2. Malfunctioning of a voltage regulator or wrong settings under manual control
(symmetrical voltage decrease).
3. Low load compared to the reactive power generation (symmetrical voltage decrease).
4. Earth-faults in high impedance earthed systems causes, beside the high voltage in the
neutral, high voltages in the two non-faulted phases, (unsymmetrical voltage increase).
OV2PTOV prevents sensitive equipment from running under conditions that could cause their
overheating or stress of insulation material, and, thus, shorten their life time expectancy. In
many cases, it is a useful function in circuits for local or remote automation processes in the
power system.
The parameters for Two step overvoltage protection (OV2PTOV) are set via the local HMI or
PCM600.
All the voltage conditions in the system where OV2PTOV performs its functions should be
considered. The same also applies to the associated equipment, its voltage and time
characteristic.
There are wide applications where general overvoltage functions are used. All voltage related
settings are made as a percentage of a settable base primary voltage, which is normally set to
the nominal voltage level (phase-to-phase) of the power system or the high voltage equipment
under consideration.
The time delay for the OV2PTOV can sometimes be critical and related to the size of the
overvoltage - a power system or a high voltage component can withstand smaller overvoltages
for some time, but in case of large overvoltages the related equipment should be disconnected
more rapidly.
Some applications and related setting guidelines for the voltage level are given below:
The hysteresis is for overvoltage functions very important to prevent that a transient voltage
over set level is not “sealed-in” due to a high hysteresis. Typical values should be ≤ 0.5%.
High voltage will cause overexcitation of the core and deteriorate the winding insulation. The
setting has to be well above the highest occurring "normal" voltage and well below the highest
acceptable voltage for the equipment.
High voltage will deteriorate the dielectricum and the insulation. The setting has to be well
above the highest occurring "normal" voltage and well below the highest acceptable voltage
for the capacitor.
The setting has to be well above the highest occurring "normal" voltage and below the highest
acceptable voltage, due to regulation, good practice or other agreements.
In high impedance earthed systems, earth-faults cause a voltage increase in the non-faulty
phases. Two step overvoltage protection (OV2PTOV) is used to detect such faults. The setting
must be above the highest occurring "normal" voltage and below the lowest occurring voltage
during faults. A metallic single-phase earth-fault causes the non-faulted phase voltages to
increase a factor of √3.
8.2.3.5 The following settings can be done for the two step overvoltage
protection M13852-22 v10
ConnType: Sets whether the measurement shall be phase-to-earth fundamental value, phase-
to-phase fundamental value, phase-to-earth RMS value or phase-to-phase RMS value.
Operation: Off/On.
UBase (given in GlobalBaseSel): Base voltage phase to phase in primary kV. This voltage is used
as reference for voltage setting. OV2PTOV measures selectively phase-to-earth voltages, or
phase-to-phase voltage chosen by the setting ConnType. The function will operate if the
voltage gets lower than the set percentage of UBase. When ConnType is set to PhN DFT or PhN
RMS then the IED automatically divides set value for UBase by √3. When ConnType is set to
PhPh DFT or PhPh RMS then set value for UBase is used. Therefore, always set UBase as rated
primary phase-to-phase voltage of the protected object. If phase to neutral (PhN)
measurement is selected as setting, the operation of phase-to-earth over voltage is
automatically divided by sqrt3. This means operation for phase-to-earth voltage over:
The below described setting parameters are identical for the two steps (n = 1 or 2). Therefore
the setting parameters are described only once.
Characteristicn: This parameter gives the type of time delay to be used. The setting can be
Definite time, Inverse Curve A, Inverse Curve B, Inverse Curve C or I/Prog. inv. curve. The choice
is highly dependent of the protection application.
OpModen: This parameter describes how many of the three measured voltages that should be
above the set level to give operation. The setting can be 1 out of 3, 2 out of 3, 3 out of 3. In
most applications it is sufficient that one phase voltage is high to give operation. If the
function shall be insensitive for single phase-to-earth faults 1 out of 3 can be chosen, because
the voltage will normally rise in the non-faulted phases at single phase-to-earth faults. In
subtransmission and transmission networks the UV function is mainly a system supervision
function and 3 out of 3 is selected.
Un>: Set operate overvoltage operation value for step n, given as % of UBase. The setting is
highly dependent of the protection application. Here it is essential to consider the maximum
voltage at non-faulted situations. Normally this voltage is less than 110% of nominal voltage.
tn: time delay of step n, given in s. The setting is highly dependent of the protection
application. In many applications the protection function is used to prevent damages to the
protected object. The speed might be important for example in case of protection of
transformer that might be overexcited. The time delay must be co-ordinated with other
automated actions in the system.
tResetn: Reset time for step n if definite time delay is used, given in s. The default value is 25
ms.
tnMin: Minimum operation time for inverse time characteristic for step n, given in s. For very
high voltages the overvoltage function, using inverse time characteristic, can give very short
operation time. This might lead to unselective trip. By setting t1Min longer than the operation
time for other protections such unselective tripping can be avoided.
ResetTypeCrvn: This parameter for inverse time characteristic can be set: Instantaneous,
Frozen time, Linearly decreased. The default setting is Instantaneous.
tIResetn: Reset time for step n if inverse time delay is used, given in s. The default value is 25
ms.
kn: Time multiplier for inverse time characteristic. This parameter is used for co-ordination
between different inverse time delayed undervoltage protections.
ACrvn, BCrvn, CCrvn, DCrvn, PCrvn: Parameters to set to create programmable under voltage
inverse time characteristic. Description of this can be found in the technical reference manual.
CrvSatn: When the denominator in the expression of the programmable curve is equal to zero
the time delay will be infinity. There will be an undesired discontinuity. Therefore a tuning
parameter CrvSatn is set to compensate for this phenomenon. In the voltage interval Un> up
to Un> · (1.0 + CrvSatn/100) the used voltage will be: Un> · (1.0 + CrvSatn/100). If the
programmable curve is used, this parameter must be calculated so that:
CrvSatn
B× -C > 0
100
EQUATION1448 V1 EN-US (Equation 36)
HystAbsn: Absolute hysteresis set in % of UBase. The setting of this parameter is highly
dependent of the application. If the function is used as control for automatic switching of
reactive compensation devices the hysteresis must be set smaller than the voltage change
after switching of the compensation device.
8.3.1 Identification
SEMOD54295-2 v6
IEC15000108 V1 EN-US
Two step residual overvoltage protection ROV2PTOV is primarily used in high impedance
earthed distribution networks, mainly as a backup for the primary earth-fault protection of the
feeders and the transformer. To increase the security for different earth-fault related
functions, the residual overvoltage signal can be used as a release signal. The residual voltage
can be measured either at the transformer neutral or from a voltage transformer open delta
connection. The residual voltage can also be calculated internally, based on the measurement
of the three phase-to-earth voltages.
In high impedance earthed systems the residual voltage will increase in case of any fault
connected to earth. Depending on the type of fault and fault resistance the residual voltage
will reach different values. The highest residual voltage, equal to three times the phase-to-
earth voltage, is achieved for a single phase-to-earth fault. The residual voltage increases
approximately to the same level in the whole system and does not provide any guidance in
finding the faulted component. Therefore, ROV2PTOV is often used as a backup protection or
as a release signal for the feeder earth-fault protection.
All the voltage conditions in the system where ROV2PTOV performs its functions should be
considered. The same also applies to the associated equipment, its voltage withstand
capability and time characteristic.
All voltage-related settings are made as a percentage of a settable base voltage, which shall be
set to the primary nominal voltage (phase-phase) level of the power system or the high-
voltage equipment under consideration.
The time delay for ROV2PTOV is seldom critical, since residual voltage is related to earth faults
in a high-impedance earthed system, and enough time must normally be given for the primary
protection to clear the fault. In some more specific situations, where the residual overvoltage
protection is used to protect some specific equipment, the time delay is shorter.
Some applications and related setting guidelines for the residual voltage level are given below.
High residual voltage indicates earth-fault in the system, perhaps in the component to which
two step residual overvoltage protection (ROV2PTOV) is connected. For selectivity reasons to
the primary protection for the faulted device, ROV2PTOV must trip the component with some
time delay. The setting must be above the highest occurring "normal" residual voltage and
below the highest acceptable residual voltage for the equipment.
High voltage will deteriorate the dielectric and the insulation. Two step residual overvoltage
protection (ROV2PTOV) has to be connected to a neutral or open delta winding. The setting
must be above the highest occurring "normal" residual voltage and below the highest
acceptable residual voltage for the capacitor.
The setting must be above the highest occurring "normal" residual voltage and below the
highest acceptable residual voltage, due to regulation, good practice or other agreements.
In high impedance earthed systems, earth faults cause a neutral voltage in the feeding
transformer neutral. Two step residual overvoltage protection ROV2PTOV is used to trip the
transformer, as a backup protection for the feeder earth-fault protection, and as a backup for
the transformer primary earth-fault protection. The setting must be above the highest
occurring "normal" residual voltage, and below the lowest occurring residual voltage during
the faults under consideration. A metallic single-phase earth fault causes a transformer neutral
to reach a voltage equal to the nominal phase-to-earth voltage.
The voltage transformers measuring the phase-to-earth voltages measure zero voltage in the
faulty phase. The two healthy phases will measure full phase-to-phase voltage, as the faulty
phase will be connected to earth. The residual overvoltage will be three times the phase-to-
earth voltage. See figure 50.
UL1
3U0
IEC07000190-2-en.vsd
IEC07000190 V2 EN-US
In direct earthed systems, an earth fault on one phase is indicated by voltage collapse in that
phase. The other healthy phase will still have normal phase-to-earth voltage. The residual sum
will have the same value as the remaining phase-to-earth voltage, which is shown in Figure 51.
UL1
IEC07000189-2-en.vsd
IEC07000189 V2 EN-US
8.3.3.6 Settings for two step residual overvoltage protection M13853-21 v14
Operation: Off or On
UBase (given in GlobalBaseSel) is used as voltage reference for the set pickup values. The
voltage can be fed to the IED in different ways:
1. The IED is fed from a normal voltage transformer group where the residual voltage is
calculated internally from the phase-to-earth voltages within the protection. The setting
of the analog input is given as UBase=Uph-ph.
2. The IED is fed from a broken delta connection normal voltage transformer group. In an
open delta connection the protection is fed by the voltage 3U0 (single input). Section
Analog inputs in the Application manual explains how the analog input needs to be set.
3. The IED is fed from a single voltage transformer connected to the neutral point of a power
transformer in the power system. In this connection the protection is fed by the voltage
UN=U0 (single input). Section Analog inputs in the Application manual explains how the
analog input needs to be set.
ROV2PTOV will measure the residual voltage corresponding to the nominal phase-to-earth
voltage for a high-impedance earthed system. The measurement will be based on the neutral
voltage displacement.
The setting parameters described below are identical for the two steps (n = step 1 and 2).
Therefore the setting parameters are described only once.
Characteristicn: Selected inverse time characteristic for step n. This parameter gives the type
of time delay to be used. The setting can be, Definite time or Inverse curve A or Inverse curve B
or Inverse curve C or Prog. inv. curve. The choice is highly dependent of the protection
application.
Un>: Set operate overvoltage operation value for step n, given as % of residual voltage
corresponding to UBase:
U > ( % ) × UBase ( kV ) 3
IECEQUATION2290 V1 EN-US (Equation 37)
The setting depends on the required sensitivity of the protection and the type of system
earthing. In non-effectively earthed systems, the residual voltage cannot be higher than three
times the rated phase-to-earth voltage, which should correspond to 100%.
In effectively earthed systems, this value depends on the ratio Z0/Z1. The required setting to
detect high resistive earth faults must be based on network calculations.
tn: time delay of step n, given in s. The setting is highly dependent on the protection
application. In many applications, the protection function has the task to prevent damage to
the protected object. The speed might be important, for example, in the case of the protection
of a transformer that might be overexcited. The time delay must be co-ordinated with other
automated actions in the system.
tResetn: Reset time for step n if definite time delay is used, given in s. The default value is 25
ms.
tnMin: Minimum operation time for inverse time characteristic for step n, given in s. For very
high voltages the overvoltage function, using inverse time characteristic, can give very short
operation time. This might lead to unselective trip. By setting t1Min longer than the operation
time for other protections such unselective tripping can be avoided.
ResetTypeCrvn: Set reset type curve for step n. This parameter can be set:
Instantaneous,Frozen time,Linearly decreased. The default setting is Instantaneous.
tIResetn: Reset time for step n if inverse time delay is used, given in s. The default value is 25
ms.
kn: Time multiplier for inverse time characteristic. This parameter is used for co-ordination
between different inverse time delayed undervoltage protections.
ACrvn, BCrvn, CCrvn, DCrvn, PCrvn: Parameters for step n, to set to create programmable
undervoltage inverse time characteristic. Description of this can be found in the technical
reference manual.
CrvSatn: Set tuning parameter for step n. When the denominator in the expression of the
programmable curve is equal to zero, the time delay will be infinite. There will be an undesired
discontinuity. Therefore, a tuning parameter CrvSatn is set to compensate for this
phenomenon. In the voltage interval U> up to U> · (1.0 + CrvSatn/100) the used voltage will be:
U> · (1.0 + CrvSatn/100). If the programmable curve is used this parameter must be calculated
so that:
CrvSatn
B× -C > 0
100
EQUATION1448 V1 EN-US (Equation 38)
HystAbsn: Absolute hysteresis for step n, set in % of UBase. The setting of this parameter is
highly dependent of the application. The hysteresis is used to avoid oscillations of the START
output signal. This signal resets when the measured voltage drops below the setting level and
leaves the hysteresis area. Make sure that the set value for parameter HystABSn is somewhat
smaller than the set pickup value. Otherwise there is a risk that step n will not reset properly.
9.1.1 Identification
M14869-1 v4
Different protection functions within the protection IED, operates on the basis of the
measured voltage in the relay point. Examples are:
These functions can operate unintentionally if a fault occurs in the secondary circuits between
the voltage instrument transformers and the IED.
It is possible to use different measures to prevent such unwanted operations. Miniature circuit
breakers in the voltage measuring circuits should be located as close as possible to the
voltage instrument transformers, and shall be equipped with auxiliary contacts that are wired
to the IEDs. Separate fuse-failure monitoring IEDs or elements within the protection and
monitoring devices are another possibilities. These solutions are combined to get the best
possible effect in the fuse failure supervision function (FUFSPVC).
FUFSPVC function built into the IED products can operate on the basis of external binary
signals from the miniature circuit breaker or from the line disconnector. The first case
influences the operation of all voltage-dependent functions while the second one does not
affect the impedance measuring functions.
The zero sequence detection algorithm, based on the zero sequence measuring quantities is
recommended for use in directly or low impedance earthed networks: a high value of voltage
3U0 without the presence of the residual current 3I0 is a condition that is related to a fuse
failure event. In cases where the line can have a weak-infeed of zero sequence current this
function shall be avoided.
A criterion based on delta current and delta voltage measurements can be added to the fuse
failure supervision function in order to detect a three phase fuse failure. This is beneficial for
example during three phase transformer switching.
The negative and zero sequence voltages and currents always exist due to different non-
symmetries in the primary system and differences in the current and voltage instrument
transformers. The minimum value for the operation of the current and voltage measuring
elements must always be set with a safety margin of 10 to 20%, depending on the system
operating conditions.
Pay special attention to the dissymmetry of the measuring quantities when the function is
used on long untransposed lines, on multicircuit lines and so on.
The settings of negative sequence, zero sequence and delta algorithm are in percent of the
base voltage and base current for the function. Common base IED values for primary current
(IBase), primary voltage (UBase) and primary power (SBase) are set in Global Base Values
GBASVAL. The setting GlobalBaseSel is used to select a particular GBASVAL and used its base
values.
Set the operation mode selector Operation to On to release the fuse failure function.
The voltage threshold USealIn< is used to identify low voltage condition in the system. Set
USealIn< below the minimum operating voltage that might occur during emergency
conditions. We propose a setting of approximately 70% of UBase.
The drop off time of 200 ms for dead phase detection makes it recommended to always set
SealIn to On since this will secure a fuse failure indication at persistent fuse fail when closing
the local breaker when the line is already energized from the other end. When the remote
breaker closes the voltage will return except in the phase that has a persistent fuse fail. Since
the local breaker is open there is no current and the dead phase indication will persist in the
phase with the blown fuse. When the local breaker closes the current will start to flow and the
function detects the fuse failure situation. But due to the 200 ms drop off timer the output
BLKZ will not be activated until after 200 ms. This means that distance functions are not
blocked and due to the “no voltage but current” situation might issue a trip.
The operation mode selector OpMode has been introduced for better adaptation to system
requirements. The mode selector enables selecting interactions between the negative
sequence and zero sequence algorithm. In normal applications, the OpMode is set to either
UNsINs for selecting negative sequence algorithm or UZsIZs for zero sequence based
algorithm. If system studies or field experiences shows that there is a risk that the fuse failure
function will not be activated due to the system conditions, the dependability of the fuse
failure function can be increased if the OpMode is set to UZsIZs OR UNsINs or OptimZsNs. In
mode UZsIZs OR UNsINs both negative and zero sequence based algorithms are activated and
working in an OR-condition. Also in mode OptimZsNs both negative and zero sequence
algorithms are activated and the one that has the highest magnitude of measured negative or
zero sequence current will operate. If there is a requirement to increase the security of the fuse
failure function OpMode can be selected to UZsIZs AND UNsINs which gives that both negative
and zero sequence algorithms are activated and working in an AND-condition, that is, both
algorithms must give condition for block in order to activate the output signals BLKU or BLKZ.
The relay setting value 3U2> is given in percentage of the base voltage UBase and should not
be set lower than the value that is calculated according to equation 39.
U2
3U 2 100
UBase 3
EQUATION1519 V5 EN-US (Equation 39)
where:
U2 is the maximal negative sequence voltage during normal operation conditions, plus a margin of
10...20%
UBase is the base voltage for the function according to the setting GlobalBaseSel
The setting of the current limit 3I2< is in percentage of parameter IBase. The setting of 3I2<
must be higher than the normal unbalance current that might exist in the system and can be
calculated according to equation 40.
I2
3 I 2 100
IBase
EQUATION1520 V5 EN-US (Equation 40)
where:
I2 is the maximal negative sequence current during normal operating conditions, plus a margin of
10...20%
IBase is the base current for the function according to the setting GlobalBaseSel
The IED setting value 3U0> is given in percentage of the base voltage UBase. The setting of
3U0> should not be set lower than the value that is calculated according to equation 41.
3U 0
3U 0 100
UBase 3
EQUATION1521 V4 EN-US (Equation 41)
where:
3U0 is the maximal zero sequence voltage during normal operation conditions, plus a margin of 10...20%
UBase is the base voltage for the function according to the setting GlobalBaseSel
The setting of the current limit 3I0< is done in percentage of IBase. The setting of 3I0< must
be higher than the normal unbalance current that might exist in the system. The setting can be
calculated according to equation 42.
3I 0
3I 0< = ×100
IBase
EQUATION2293 V3 EN-US (Equation 42)
where:
3I0< is the maximal zero sequence current during normal operating conditions, plus a margin of 10...20%
IBase is the base current for the function according to the setting GlobalBaseSel
Set the operation mode selector OpDUDI to On if the delta function shall be in operation.
The setting of DU> should be set high (approximately 60% of UBase) and the current threshold
DI< low (approximately 10% of IBase) to avoid unwanted operation due to normal switching
conditions in the network. The delta current and delta voltage function shall always be used
together with either the negative or zero sequence algorithm. If USetprim is the primary voltage
for operation of dU/dt and ISetprim the primary current for operation of dI/dt, the setting of
DU> and DI< will be given according to equation 43 and equation 44.
USet prim
DU > = .100
UBase
EQUATION1523 V3 EN-US (Equation 43)
ISet prim
DI< = . 100
IBase
EQUATION1524 V4 EN-US (Equation 44)
The voltage thresholds UPh> is used to identify low voltage condition in the system. Set UPh>
below the minimum operating voltage that might occur during emergency conditions. A
setting of approximately 70% of UBase is recommended.
The current threshold IPh> shall be set lower than the IMinOp for the distance protection
function. A 5...10% lower value is recommended.
The condition for operation of the dead line detection is set by the parameters IDLD< for the
current threshold and UDLD< for the voltage threshold.
Set the IDLD< with a sufficient margin below the minimum expected load current. A safety
margin of at least 15-20% is recommended. The operate value must however exceed the
maximum charging current of an overhead line, when only one phase is disconnected (mutual
coupling to the other phases).
Set the UDLD< with a sufficient margin below the minimum expected operating voltage. A
safety margin of at least 15% is recommended.
Section 10 Control
10.1 Apparatus control IP14560-1 v3
The apparatus control is a functionality for control and supervising of circuit breakers,
disconnectors, and earthing switches within a bay. Permission to operate is given after
evaluation of conditions from other functions such as interlocking, synchrocheck, operator
place selection and external or internal blockings.
The complete apparatus control function is not included in this product, and
the information below is included for understanding of the principle for the use
of QCBAY, LOCREM, LOCREMCTRL, SCILO, SCSWI, SXCBR.
Figure 52 shows from which places the apparatus control function receives commands. The
commands to an apparatus can be initiated from the Control Centre (CC), the station HMI or
the local HMI on the IED front.
cc
Station HMI
GW
Station bus
The signal flow between the function blocks is shown in Figure 53. The application description
for all these functions can be found below. The function SCILO in the Figure below is the
logical node for interlocking.
When the circuit breaker or switch is located in a breaker IED, two more functions are added:
The extension of the signal flow and the usage of the GOOSE communication are shown in
Figure 54.
IEC 61850
-QB9
IEC17000061=1=en=Orignal.ai
IEC17000061 V1 EN-US
Figure 53: Signal flow between apparatus control function blocks when all functions are
situated within the IED
IEC 61850 on
station bus
SCILO
GOOSEXLNRCV XLNPROXY
SCSWI
SCILO
GOOSEXLNRCV XLNPROXY
Merging Unit
XCBR
XCBR -QB1
XCBR -QA1
-QB9
IEC17000062=1=en=Original.vsdx
IEC17000062 V1 EN-US
Figure 54: Signal flow between apparatus control functions with XCBR and XSWI located
in a breaker IED
Control operation can be performed from the local IED HMI. If users are defined in the IED,
then the local/remote switch is under authority control, otherwise the default user can
perform control operations from the local IED HMI without logging in. The default position of
the local/remote switch is on remote.
The accepted originator categories for each PSTO value are shown in Table 19.
PSTO = All, then it is no priority between operator places. All operator places are allowed to
operate.
According to IEC 61850 standard the orCat attribute in originator category are defined in
Table 20
Value Description
0 not-supported
1 bay-control
2 station-control
3 remote-control
4 automatic-bay
5 automatic-station
6 automatic-remote
7 maintenance
8 process
The Bay control (QCBAY) is used to handle the selection of the operator place per bay. The
function gives permission to operate from two main types of locations either from Remote
(for example, control centre or station HMI) or from Local (local HMI on the IED) or from all
(Local and Remote). The Local/Remote switch position can also be set to Off, which means no
operator place selected that is, operation is not possible either from local or from remote.
For IEC 61850-8-1 communication, the Bay Control function can be set to discriminate between
commands with orCat station and remote (2 and 3). The selection is then done through the IEC
61850-8-1 edition 2 command LocSta.
QCBAY also provides blocking functions that can be distributed to different apparatuses
within the bay. There are two different blocking alternatives:
IEC13000016-2-en.vsd
IEC13000016 V2 EN-US
SCSWI may handle and operate on one three-phase device or three one-phase switching
devices.
After the selection of an apparatus and before the execution, the switch controller performs
the following checks and actions:
In the case when there are three one-phase switches (SXCBR) connected to the switch
controller function, the switch controller will "merge" the position of the three switches to the
resulting three-phase position. In case of a pole discordance situation, that is, the positions of
the one-phase switches are not equal for a time longer than a settable time; an error signal will
be given.
The switch controller represents the content of the SCSWI logical node (according to IEC
61850) with mandatory functionality.
Switches are functions used to close and interrupt an ac power circuit under normal
conditions, or to interrupt the circuit under fault, or emergency conditions. The intention with
these functions is to represent the lowest level of a power-switching device with or without
short circuit breaking capability, for example, circuit breakers, disconnectors, earthing
switches etc.
The purpose of these functions is to provide the actual status of positions and to perform the
control operations, that is, pass all the commands to the primary apparatus via output boards
and to supervise the switching operation and position.
The realizations of these functions are done with SXCBR representing a circuit breaker.
Circuit breaker (SXCBR) can be realized either as three one-phase switches or as one three-
phase switch.
The content of this function is represented by the IEC 61850 definitions for the logical node
Circuit breaker (SXCBR) with mandatory functionality.
10.1.5 Proxy for signals from switching device via GOOSE XLNPROXY GUID-2DA1E47C-5A9A-4C53-8D60-7B1729EF6B90 v1
The purpose of the proxy for signals from switching device via GOOSE (XLNPROXY) is to give
the same internal representation of the position status and control response for a switch
modeled in a breaker IED as if represented by a SXCBR or SXSWI function.
Since different switches are represented differently on IEC 61850, the data that is mandatory
to model in IEC 61850 is mandatory inputs and the other useful data for the command and
status following is optional. To make it easy to choose which data to use for the XLNPROXY
function, their usage is controlled by the connection of each data’s signal input and valid input.
These connections are usually from the GOOSEXLNRCV function (see Figure 56 and Figure 57).
IEC16000071 V1 EN-US
Figure 56: Configuration with XLNPROXY and GOOSEXLNRCV where all the IEC 61850
modelled data is used, including selection
IEC16000072 V1 EN-US
Figure 57: Configuration with XLNPROXY and GOOSEXLNRCV where only the mandatory
data in the IEC 61850 modelling is used
All the information from the XLNPROXY to the SCSWI about command following status, causes
for failed command and selection status is transferred in the output XPOS. The other outputs
may be used by other functions in the same way as the corresponding outputs of the SXCBR
and SXSWI function.
When a command has been issued from the connected SCSWI function, the XLNPROXY
function awaits the response on it from the represented switch through the inputs POSVAL
and OPOK. While waiting for the switch to start moving, it checks if the switch is blocked for
the operation. When the switch has started moving and no blocking condition has been
detected, XLNPROXY issues a response to the SCSWI function that the command has started.
If OPOK is used, this response is given when XLNPROXY receives the signal.
If no movement of the switch is registered within the limit tStartMove, the command is
considered failed, and the cause of the failure is evaluated. In the evaluation, the function
checks if the state of the represented switch is indicating that the command is blocked in any
way during the command, and gives the appropriate cause to the SCSWI function. This cause is
also shown on the output L_CAUSE as indicated in the following table:
The OPCAP input and output are used for the CBOpCap data of a XCBR
respectively SwOpCap for a XSWI. The interpretation for the command
following is controlled through the setting SwitchType.
A typical bay with apparatus control function consists of a combination of logical nodes or
functions that are described here:
• The Switch controller (SCSWI) initializes all operations for one apparatus. It is the
command interface of the apparatus. It includes the position reporting as well as the
control of the position
• The Circuit breaker (SXCBR) is the process interface to the circuit breaker for the
apparatus control function.
• The Bay control (QCBAY) fulfils the bay-level functions for the apparatuses, such as
operator place selection and blockings for the complete bay.
• The Protection trip logic (SMPPTRC) connects the "trip" outputs of one or more protection
functions to a common "trip" to be transmitted to SXCBR.
• The Autorecloser (SMBRREC) consists of the facilities to automatically close a tripped
breaker with respect to a number of configurable conditions.
• The logical node Interlocking (SCILO) provides the information to SCSWI whether it is
permitted to operate due to the switchyard topology. The interlocking conditions are
evaluated with separate logic and connected to SCILO .
• The Synchrocheck, energizing check, and synchronizing (SESRSYN) calculates and
compares the voltage phasor difference from both sides of an open breaker with
predefined switching conditions (synchrocheck). Also the case that one side is dead
(energizing-check) is included.
• The Generic Automatic Process Control function, GAPC, handles generic commands from
the operator to the system.
The overview of the interaction between these functions is shown in Figure 58 below.
Trip
Synchrocheck
Synchronizing
Synchronizing
in progress
Start
OK
Close cmd
SCSWI SXCBR
(Switching control) (Circuit breaker)
Close CB
SMBRREC
Enable
Enable
close
open
(Auto- Position
reclosure)
I/O
SCILO
(Interlocking)
other bays
Pos. from
Open rel.
Interlocking Close rel.
function Open rel.
block Close rel. SCILO
(Not a LN) Position (Interlocking)
Enable Enable
open close
GAPC
(Generic
Automatic SCSWI
Process Open/Close (Switching control)
Control) Open/Close
IEC17000063=1=en=Original..vsdx
IEC17000063 V1 EN-US
Figure 58: Example overview of the interactions between functions in a typical bay
The setting parameters for the apparatus control function are set via the local HMI or PCM600.
If the parameter AllPSTOValid is set to No priority, all originators from local and remote are
accepted without any priority.
If the parameter RemoteIncStation is set to Yes, commands from IEC 61850-8-1 clients at both
station and remote level are accepted, when the QCBAY function is in Remote. If set to No, the
command LocSta controls which operator place is accepted when QCBAY is in Remote. If
LocSta is true, only commands from station level are accepted, otherwise only commands
from remote level are accepted.
The parameter CtlModel specifies the type of control model according to IEC 61850. The
default for control of circuit breakers, disconnectors and earthing switches the control model
is set to SBO Enh (Select-Before-Operate) with enhanced security.
When the operation shall be performed in one step, and no monitoring of the result of the
command is desired, the model direct control with normal security is used.
At control with enhanced security there is an additional supervision of the status value by the
control object, which means that each command sequence must be terminated by a
termination command.
tSelect is the maximum allowed time between the select and the execute command signal,
that is, the time the operator has to perform the command execution after the selection of the
object to operate. When the time has expired, the selected output signal is set to false and a
cause-code is given.
The time parameter tResResponse is the allowed time from reservation request to the
feedback reservation granted from all bays involved in the reservation function. When the time
has expired, the control function is reset, and a cause-code is given.
tSynchrocheck is the allowed time for the synchrocheck function to fulfill the close conditions.
When the time has expired, the function tries to start the synchronizing function. If
tSynchrocheck is set to 0, no synchrocheck is done, before starting the synchronizing function.
The timer tSynchronizing supervises that the signal synchronizing in progress is obtained in
SCSWI after start of the synchronizing function. The start signal for the synchronizing is set if
the synchrocheck conditions are not fulfilled. When the time has expired, the control function
is reset, and a cause-code is given. If no synchronizing function is included, the time is set to 0,
which means no start of the synchronizing function is done, and when tSynchrocheck has
expired, the control function is reset and a cause-code is given.
tExecutionFB is the maximum time between the execute command signal and the command
termination. When the time has expired, the control function is reset and a cause-code is
given.
tPoleDiscord is the allowed time to have discrepancy between the poles at control of three
one-phase breakers. At discrepancy an output signal is activated to be used for trip or alarm,
and during a command, the control function is reset, and a cause-code is given.
SuppressMidPos when On suppresses the mid-position during the time tIntermediate of the
connected switches.
The parameter InterlockCheck decides if interlock check should be done at both select and
operate, Sel & Op phase, or only at operate, Op phase.
tStartMove is the supervision time for the apparatus to start moving after a command
execution is done from the SCSWI function. When the time has expired, the command
supervision is reset, and a cause-code is given.
During the tIntermediate time, the position indication is allowed to be in an intermediate (00)
state. When the time has expired, the command supervision is reset, and a cause-code is given.
The indication of the mid-position at SCSWI is suppressed during this time period when the
position changes from open to close or vice-versa if the parameter SuppressMidPos is set to
On in the SCSWI function.
If the parameter AdaptivePulse is set to Adaptive the command output pulse resets when a
new correct end position is reached. If the parameter is set to Not adaptive the command
output pulse remains active until the timer tOpenPulsetClosePulse has elapsed.
tOpenPulse is the output pulse length for an open command. If AdaptivePulse is set to
Adaptive, it is the maximum length of the output pulse for an open command. The default
length is set to 200 ms for a circuit breaker (SXCBR).
tClosePulse is the output pulse length for a close command. If AdaptivePulse is set to
Adaptive, it is the maximum length of the output pulse for an open command. The default
length is set to 200 ms for a circuit breaker (SXCBR).
10.1.7.4 Proxy for signals from switching device via GOOSE XLNPROXY GUID-7C253FE7-6E02-4F94-96C7-81C9129D925D v1
The SwitchType setting controls the evaluation of the operating capability. If SwitchType is set
to Circuit Breaker, the input OPCAP is interpreted as a breaker operating capability, otherwise
it is interpreted as a switch operating capability.
tStartMove is the supervision time for the apparatus to start moving after a command
execution is done from the SCSWI function. When the time has expired, the command
supervision is reset, and a cause-code is given.
During the tIntermediate time, the position indication is allowed to be in an intermediate (00)
state. When the time has expired, the command supervision is reset, and a cause-code is given.
The indication of the mid-position at SCSWI is suppressed during this time period when the
position changes from open to close or vice-versa if the parameter SuppressMidPos is set to
On in the SCSWI function.
In most cases, the same value can be used for both tStartMove and tIntermediate as in the
source function. However, tStartMove may need to be increased to accommodate for the
communication delays, mainly when representing a circuit breaker.
10.2.1 Identification
SEMOD167845-2 v3
The logic rotating switch for function selection and LHMI presentation function (SLGAPC) (or
the selector switch function block, as it is also known) is used to get a selector switch
functionality similar with the one provided by a hardware multi-position selector switch.
Hardware selector switches are used extensively by utilities, in order to have different
functions operating on pre-set values. Hardware switches are however sources for
maintenance issues, lower system reliability and extended purchase portfolio. The virtual
selector switches eliminate all these problems.
SLGAPC function block has two operating inputs (UP and DOWN), one blocking input (BLOCK)
and one operator position input (PSTO).
SLGAPC can be activated both from the local HMI and from external sources (switches) via the
IED binary inputs. It also allows the operation from remote (like the station computer).
SWPOSN is an integer value output, giving the actual output number. Since the number of
positions of the switch can be established by settings (see below), one must be careful in
coordinating the settings with the configuration (if one sets the number of positions to x in
settings – for example, there will be only the first x outputs available from the block in the
configuration). Also the frequency of the (UP or DOWN) pulses should be lower than the
setting tPulse.
From the local HMI, the selector switch can be operated from Single-line diagram (SLD).
The following settings are available for the Logic rotating switch for function selection and
LHMI presentation (SLGAPC) function:
tPulse: In case of a pulsed output, it gives the length of the pulse (in seconds).
tDelay: The delay between the UP or DOWN activation signal positive front and the output
activation.
StopAtExtremes: Sets the behavior of the switch at the end positions – if set to Disabled, when
pressing UP while on first position, the switch will jump to the last position; when pressing
DOWN at the last position, the switch will jump to the first position; when set to Enabled, no
jump will be allowed.
10.3.1 Identification
SEMOD167850-2 v4
Selector mini switch (VSGAPC) function is a multipurpose function used in the configuration
tool in PCM600 for a variety of applications, as a general purpose switch. VSGAPC can be used
for both acquiring an external switch position (through the IPOS1 and the IPOS2 inputs) and
represent it through the single line diagram symbols (or use it in the configuration through the
outputs POS1 and POS2) as well as, a command function (controlled by the PSTO input), giving
switching commands through the CMDPOS12 and CMDPOS21 outputs.
The output POSITION is an integer output, showing the actual position as an integer number 0
– 3, where 0 = MidPos, 1 = Open, 2 = Closed and 3 = Error.
An example where VSGAPC is configured to switch Autorecloser on–off from a button symbol
on the local HMI is shown in figure59. The I and O buttons on the local HMI are normally used
for on–off operations of the circuit breaker.
INVERTER
VSGAPC INPUT OUT
PSTO
INTONE
IPOS1
IPOS2
SMBRREC
NAM_POS1 CMDPOS12 ON SETON
OFF
ON NAM_POS2 CMDPOS21 OFF
IEC07000112-3-en.vsd
IEC07000112 V3 EN-US
Figure 59: Control of Autorecloser from local HMI through Selector mini switch
VSGAPC is also provided with IEC 61850 communication so it can be controlled from SA
system as well.
Selector mini switch (VSGAPC) function can generate pulsed or steady commands (by setting
the Mode parameter). When pulsed commands are generated, the length of the pulse can be
set using the tPulse parameter. Also, being accessible on the single line diagram (SLD), this
function block has two control modes (settable through CtlModel): Dir Norm and SBO Enh.
10.4.1 Identification
GUID-E16EA78F-6DF9-4B37-A92D-5C09827E2297 v3
Generic communication function for Double Point indication (DPGAPC) function block is used
to send double point position indication to other systems, equipment or functions in the
substation through IEC 61850-8-1 or other communication protocols. It is especially intended
to be used in the interlocking station-wide logics. To be able to get the signals into other
systems, equipment or functions, one must use other tools, described in the Engineering
manual, and define which function block in which systems, equipment or functions should
receive this information.
More specifically, DPGAPC function reports a combined double point position indication
output POSITION, by evaluating the value and the timestamp attributes of the inputs OPEN
and CLOSE, together with the logical input signal VALID.
When the input signal VALID is active, the values of the OPEN and CLOSE inputs determine the
two-bit integer value of the output POSITION. The timestamp of the output POSITION will have
the latest updated timestamp of the inputs OPEN and CLOSE.
When the input signal VALID is inactive, DPGAPC function forces the position to intermediated
state.
When the value of the input signal VALID changes, the timestamp of the output POSITION will
be updated as the time when DPGAPC function detects the change.
Refer to Table 23 for the description of the input-output relationship in terms of the value and
the quality attributes.
The function does not have any parameters available in the local HMI or PCM600.
10.5.1 Identification
SEMOD176456-2 v3
The Single point generic control 8 signals (SPC8GAPC) function block is a collection of 8 single
point commands that can be used for direct commands for example reset of LED's or putting
IED in "ChangeLock" state from remote. In this way, simple commands can be sent directly to
the IED outputs, without confirmation. Confirmation (status) of the result of the commands is
supposed to be achieved by other means, such as binary inputs and SPGAPC function blocks.
PSTO is the universal operator place selector for all control functions. Even if
PSTO can be configured to allow LOCAL or ALL operator positions, the only
functional position usable with the SPC8GAPC function block is REMOTE.
The parameters for the single point generic control 8 signals (SPC8GAPC) function are set via
the local HMI or PCM600.
There are two settings for every command output (totally 8):
PulseModex: decides if the command signal for output x is Latched (steady) or Pulsed.
tPulsex: if PulseModex is set to Pulsed, then tPulsex will set the length of the pulse (in
seconds).
10.6.1 Identification
GUID-C3BB63F5-F0E7-4B00-AF0F-917ECF87B016 v4
Automation bits, command function for DNP3 (AUTOBITS) is used within PCM600 in order to
get into the configuration the commands coming through the DNP3.0 protocol.The AUTOBITS
function plays the same role as functions GOOSEBINRCV (for IEC 61850) and MULTICMDRCV
(for LON).AUTOBITS function block have 32 individual outputs which each can be mapped as a
Binary Output point in DNP3. The output is operated by a "Object 12" in DNP3. This object
contains parameters for control-code, count, on-time and off-time. To operate an AUTOBITS
output point, send a control-code of latch-On, latch-Off, pulse-On, pulse-Off, Trip or Close. The
remaining parameters are regarded as appropriate. For example, pulse-On, on-time=100, off-
time=300, count=5 would give 5 positive 100 ms pulses, 300 ms apart.
For description of the DNP3 protocol implementation, refer to the Communication manual.
AUTOBITS function block has one setting, (Operation: On/Off) enabling or disabling the
function. These names will be seen in the DNP3 communication management tool in PCM600.
10.7.1 Identification
GUID-2217CCC2-5581-407F-A4BC-266CD6808984 v1
Single command, 16 signals (SINGLECMD) is a common function and always included in the
IED.
The IEDs may be provided with a function to receive commands either from a substation
automation system or from the local HMI. That receiving function block has outputs that can
be used, for example, to control high voltage apparatuses in switchyards. For local control
functions, the local HMI can also be used. Together with the configuration logic circuits, the
user can govern pulses or steady output signals for control purposes within the IED or via
binary outputs.
Figure 60 shows an application example of how the user can connect SINGLECMD via
configuration logic circuit to control a high-voltage apparatus. This type of command control
is normally carried out by sending a pulse to the binary outputs of the IED. Figure 60 shows a
close operation. An open breaker operation is performed in a similar way but without the
synchro-check condition.
Single
command
function Configuration logic circuits
SINGLECMD
OUTy
User- &
defined
conditions
Synchro-
check
en04000206.vsd
IEC04000206 V2 EN-US
Figure 60: Application example showing a logic diagram for control of a circuit breaker
via configuration logic circuits
Figure 61 and figure 62 show other ways to control functions, which require steady On/Off
signals. Here, the output is used to control built-in functions or external devices.
Single
command
function Function n
SINGLECMD
Function n CMDOUTy
OUTy
en04000207.vsd
IEC04000207 V2 EN-US
Figure 61: Application example showing a logic diagram for control of built-in functions
Single
command
function Configuration logic circuits
SINGLESMD
Device 1 CMDOUTy
OUTy
User- &
defined
conditions
en04000208.vsd
IEC04000208 V2 EN-US
Figure 62: Application example showing a logic diagram for control of external devices
via configuration logic circuits
The parameters for Single command, 16 signals (SINGLECMD) are set via the local HMI or
PCM600.
Parameters to be set are MODE, common for the whole block, and CMDOUTy which includes
the user defined name for each output signal. The MODE input sets the outputs to be one of
the types Off, Steady, or Pulse.
• Off, sets all outputs to 0, independent of the values sent from the station level, that is, the
operator station or remote-control gateway.
• Steady, sets the outputs to a steady signal 0 or 1, depending on the values sent from the
station level.
• Pulse, gives a pulse with 100 ms duration, if a value sent from the station level is changed
from 0 to 1. That means the configured logic connected to the command function block
may not have a cycle time longer than the cycle time for the command function block.
Section 11 Logic
11.1 Tripping logic SMPPTRC IP14576-1 v4
11.1.1 Identification
SEMOD56226-2 v7
1 -> 0
IEC15000314 V1 EN-US
All trip signals from the different protection functions shall be routed through the trip logic. All
start signals and directional information can be routed through the trip logic as well. In its
simplest form, the trip logic will only link the TRIP signal to a binary output and make sure that
the pulse time is long enough.
If the OHL is connected to the substation via more than one breaker, one SMPPTRC function
block should be used for each breaker. For example when single-phase tripping and
autoreclosing is used on the line, both breakers are normally set up for 1/3-phase tripping and
1/3-phase autoreclosing. Alternatively, the breaker chosen as master can have single-phase
tripping, while the slave breaker could have three-phase tripping and autoreclosing. In the case
of a permanent fault, only one of the breakers has to be operated when the fault is energized a
second time. In the event of a transient fault the slave breaker performs a three-phase
reclosing onto the non-faulted line.
The same philosophy can be used for two-phase tripping and autoreclosing.
To prevent closing of a circuit breaker after a trip, the function offers a lockout function.
Connect the inputs from the protection functions to the input TRIN. The TMGAPC function
block is used to combine up to 32 inputs into one output. Connect the output TRIP to the
binary outputs on the IO board.
This signal can also be used for other purposes internally in the IED. An example could be the
starting of breaker failure protection. The three outputs TRL1, TRL2, TRL3 will always be
activated at every trip and can be utilized on individual trip outputs if single-phase operating
devices are available on the circuit breaker even when a three-phase tripping scheme is
selected.
Set the function block to Program = 3 phase and set the required length of the trip pulse to for
example, tTripMin = 150ms.
SMPPTRC
BLOCK TRIP
TMAGAPC BLKLKOUT TRL1
Protection functions with 3 phase
trip, for example time delayed TRIN TRL2
overcurrent protection TRINL1 TRL3
TRINL2 TR1P
TRINL3 TR2P
PSL1 TR3P
PSL2 CLLKOUT
PSL3 START
1PTRZ STL1
1PTREF STL2
P3PTR STL3
SETLKOUT STN
RSTLKOUT FW
STDIR REV
IEC05000544-4-en.vsdx
IEC05000544 V4 EN-US
Figure 63: Tripping logic SMPPTRC is used for a simple three-phase tripping application
The single-/three-phase tripping operation mode will give single-phase tripping for single-
phase faults and three-phase tripping for multi-phase fault. This operating mode is always
used together with a single-phase autoreclosing scheme.
The single-phase tripping operation mode can include different options and the use of the
different inputs in the function block. Inputs TRINL1, TRINL2 and TRINL3 shall be used for trip
signals from functions with built-in phase selection logic such as distance or line differential
protection functions.
The inputs 1PTRZ and 1PTREF are used for single-phase tripping from functions which do not
have built-in phase selection logic:
• 1PTRZ can be connected to the carrier aided trip signal from the distance protection
scheme (it means that another distance protection function has seen or detected the
fault)
• 1PTREF can be connected to an earth fault function such as EF4PTOC or a carrier aided
trip signal from the earth fault protection scheme
These two inputs are combined with the external phase selection logic. Phase selection signals
from the external phase selector must be connected to the inputs PSL1, PSL2 and PSL3 to
achieve the tripping on the respective single-phase trip outputs TRL1, TRL2 and TRL3. The
output TRIP is a general trip and is always activated independent of which phase is involved.
Depending on which phases are involved the outputs TR1P, TR2P and TR3P will be activated as
well.
normally connected to the output PREP3P on the autorecloser function SMBRREC but can also
be connected to other signals, for example, an external logic signal. If two circuit breakers are
involved, one SMPPTRC block instance and one SMBRREC instance are used for each circuit
breaker. This will ensure correct operation and behavior of each circuit breaker.
The output TR3P must be connected to the input TR3P on the SMBRREC function in order to
switch SMBRREC to perform a three-phase reclosing. If this signal is not activated, SMBRREC
will use single-phase dead time.
If a second line protection is utilizing the same SMBRREC, the three-phase trip
signal must be generated as OR conditions from both line protections.
Other back-up functions are connected to the input TRIN as described above for three-phase
tripping. A typical connection for a single-phase tripping scheme is shown in figure 64.
SMBRREC
PREP3P
To prepare 3 phase trip
for any trip signal
TR3P
To reset lockout
IEC05000545-5-en.vsdx
IEC05000545 V5 EN-US
Figure 64: The trip logic function SMPPTRC used for single-phase tripping application
The functionality is very similar to the single-phase scheme described above. However, in
addition to the connections for single phase SMBRREC must also be informed that the trip is
two phases by connecting the output TR2P to the input TR2P in the SMBRREC function.
The SMPPTRC function block is provided with possibilities to initiate lock-out. The lock-out can
be set to only activate the block closing output CLLKOUT or initiate the block closing output
and also maintain the trip signal output TR3P (latched trip).
The lock-out can then be manually reset after checking the primary fault by activating the
input reset lock-out RSTLKOUT.
If external conditions are required to initiate a closing circuit lock-out but not to lockout trip,
this can be achieved by activating input SETLKOUT. The setting AutoLock = Off means that the
internal trip will not activate lock-out so only initiation of the input SETLKOUT will result in
lock-out. This is normally the case for overhead line protection where most faults are transient.
Unsuccessful autoreclose and back-up zone tripping can in such cases be connected to initiate
lock-out by activating the input SETLKOUT.
An example how to connect the directional data from different application functions to the
trip function is given below, see Figure 65:
SMAGAPC SMPPTRC
STARTCOMB BLOCK STDIR BLOCK TRIP
PROTECTION 1 BLOCK STDIR STDIR1 BLKLKOUT TRL1
START START STDIR2 TRIN TRL2
FW FW STDIR3 TRINL1 TRL3
REV REV STDIR4 TRINL2 TR1P
STL1 STDIR5 TRINL3 TR2P
FWL1 STDIR6 PSL1 TR3P
REVL1 STDIR7 PSL2 CLLKOUT
STL2 STDIR8 PSL3 START
FWL2 STDIR9 1PTRZ STL1
REVL2 STDIR10 1PTREF STL2
STL3 STDIR11 P3PTR STL3
FWL3 STDIR12 SETLKOUT STN
REVL3 STDIR13 RSTLKOUT FW
STN STDIR14 STDIR REV
FWN STDIR15
REVN STDIR16
STARTCOMB
BLOCK STDIR
START
FW
PROTECTION 2 REV
STL1 STL1
FWL1 FWL1
REVL1 REVL1
STL2 STL2
FWL2 FWL2
REVL2 REVL2
STL3 STL3
FWL3 FWL3
REVL3 REVL3
STN
FWN
REVN
STARTCOMB
BLOCK STDIR
START
FW
REV
STL1
FWL1
REVL1
STL2
FWL2 PROTECTION 4
REVL2 -
STL3 STDIR
FWL3 -
PROTECTION 3 REVL3 -
STN STN
FWN FWN
REVN REVN
IEC16000180-2-en.vsdx
IEC16000180 V2 EN-US
The Start Matrix (SMAGAPC) merges start and directional output signals from different
application functions and creates a common directional output signal (STDIR) to be connected
to the Trip function (SMPPTRC). Protection functions connect their directional data via the
STARTCOMB function to SMAGAPC and then to the SMPPTRC, or directly to SMAGAPC and then
to the SMPPTRC.
The trip function (SMPPTRC) splits up the directional data as general output data for START,
STL1, STL2, STL3, STN, FW and REV.
All start and directional outputs are mapped to the logical node data model of the trip
function and provided via the IEC 61850 attributes dirGeneral, DIRL1, DIRL2, DIRL3 and DIRN.
Total block of the trip function is done by activating the input BLOCK and can be used to
disable the outputs of the trip logic in the event of internal failures. Block of lock-out output is
achieved by activating the input BLKLKOUT.
The parameters for tripping logic SMPPTRC are set via the local HMI or PCM600.
Operation: Sets the mode of operation. Off switches the tripping off. The normal selection is
On.
Program: Sets the required tripping scheme. Normally 3 phase or 1ph/3ph is used.
TripLockout: Sets the scheme for lock-out. Off only activates the closing circuit lock-out
output. On activates the closing circuit lock-out output and latches the TRIP related outputs.
The normal selection is Off.
AutoLock: Sets the scheme for lock-out. Off only activates lock-out through the input
SETLKOUT. On additionally allows lock-out activation via the trip inputs. The normal selection
is Off.
tTripMin: Sets the required minimum duration of the trip pulse. It should be set to ensure that
the circuit breaker is opened correctly. The normal setting is 0.150s.
tWaitForPHS: Sets a duration during which external phase selection must operate in order to
get a single phase trip, after any of the inputs 1PTRZ or 1PTREF has been activated. If no phase
selection has been achieved, a three-phase trip will be issued after this time has elapsed.
11.2.1 Identification
SEMOD167882-2 v3
The trip matrix logic (TMAGAPC) function is used to route trip signals and other logical output
signals to different output contacts on the IED.
The trip matrix logic function has 3 output signals and these outputs can be connected to
physical tripping outputs according to the specific application needs for settable pulse or
steady output.
PulseTime: Defines the pulse time when in Pulsed mode. When used for direct tripping of
circuit breaker(s) the pulse time delay shall be set to approximately 0.150 seconds in order to
obtain satisfactory minimum duration of the trip pulse to the circuit breaker trip coils.
OnDelay: Used to prevent output signals to be given for spurious inputs. Normally set to 0 or a
low value.
OffDelay: Defines a delay of the reset of the outputs after the activation conditions no longer
are fulfilled. It is only used in Steady mode. When used for direct tripping of circuit breaker(s)
the off delay time shall be set to at least 0.150 seconds in order to obtain a satisfactory
minimum duration of the trip pulse to the circuit breaker trip coils.
Group alarm logic function ALMCALH is used to route alarm signals to different LEDs and/or
output contacts on the IED.
ALMCALH output signal and the physical outputs allows the user to adapt the alarm signal to
physical tripping outputs according to the specific application needs.
Operation: On or Off
Group warning logic function WRNCALH is used to route warning signals to LEDs and/or
output contacts on the IED.
WRNCALH output signal WARNING and the physical outputs allows the user to adapt the
warning signal to physical tripping outputs according to the specific application needs.
OperationOn or Off
Group indication logic function INDCALH is used to route indication signals to different LEDs
and/or output contacts on the IED.
INDCALH output signal IND and the physical outputs allows the user to adapt the indication
signal to physical outputs according to the specific application needs.
Operation: On or Off
• Configurable logic blocks that do not propagate the time stamp and the quality of signals.
They do not have the suffix QT at the end of their function block name, for example,
SRMEMORY. These logic blocks are also available as part of an extension logic package
with the same number of instances.
• Configurable logic blocks that propagate the time stamp and the quality of signals. They
have the suffix QT at the end of their function block name, for example, SRMEMORYQT.
A set of standard logic blocks, like AND, OR etc, and timers are available for adapting the IED
configuration to the specific application needs.
There are no settings for AND gates, OR gates, inverters or XOR gates.
For normal On/Off delay and pulse timers the time delays and pulse lengths are set from the
local HMI or via the PST tool.
Both timers in the same logic block (the one delayed on pick-up and the one delayed on drop-
out) always have a common setting value.
For controllable gates, settable timers and SR flip-flops with memory, the setting parameters
are accessible via the local HMI or via the PST tool.
Execution of functions as defined by the configurable logic blocks runs according to a fixed
sequence with different cycle times.
For each cycle time, the function block is given an serial execution number. This is shown when
using the ACT configuration tool with the designation of the function block and the cycle time,
see example below.
IEC09000695_2_en.vsd
IEC09000695 V2 EN-US
Figure 66: Example designation, serial execution number and cycle time for logic
function
The execution of different function blocks within the same cycle is determined by the order of
their serial execution numbers. Always remember this when connecting two or more logical
function blocks in series.
Always be careful when connecting function blocks with a fast cycle time to
function blocks with a slow cycle time.
Remember to design the logic circuits carefully and always check the execution
sequence for different functions. In other cases, additional time delays must be
introduced into the logic schemes to prevent errors, for example, race between
functions.
11.7.1 Identification
SEMOD167904-2 v2
The Fixed signals function (FXDSIGN) has nine pre-set (fixed) signals that can be used in the
configuration of an IED, either for forcing the unused inputs in other function blocks to a
certain level/value, or for creating certain logic. Boolean, integer, floating point, string types of
signals are available.
When used for auto-transformers, information from both windings parts, together with the
neutral point current, needs to be available to the function. This means that three inputs are
needed.
REFPDIF
I3PW1CT1
I3PW2CT1
I3P
IEC09000619_3_en.vsd
IEC09000619 V3 EN-US
REFPDIF
I3PW1CT1
I3PW2CT1
I3P
FXDSIGN
GRP_OFF
IEC09000620_3_en.vsd
IEC09000620 V3 EN-US
11.8.1 Identification
SEMOD175721-2 v2
Boolean 16 to integer conversion function B16I is used to transform a set of 16 binary (logical)
signals into an integer. It can be used – for example, to connect logical output signals from a
function (like distance protection) to integer inputs from another function (like line differential
protection). B16I does not have a logical node mapping.
Values of each of the different OUTx from function block B16I for 1≤x≤16.
The sum of the value on each INx corresponds to the integer presented on the output OUT on
the function block B16I.
The sum of the numbers in column “Value when activated” when all INx (where 1≤x≤16) are
active that is=1; is 65535. 65535 is the highest boolean value that can be converted to an
integer by the B16I function block.
11.9.1 Identification
SEMOD175757-2 v5
Boolean to integer conversion with logical node representation, 16 bit (BTIGAPC) is used to
transform a set of 16 binary (logical) signals into an integer. BTIGAPC has a logical node
mapping in IEC 61850.
The BTIGAPC function will transfer a combination of up to 16 binary inputs INx where 1≤x≤16 to
an integer. Each INx represents a value according to the table below from 0 to 32768. This
follows the general formula: INx = 2x-1 where 1≤x≤16. The sum of all the values on the activated
INx will be available on the output OUT as a sum of the values of all the inputs INx that are
activated. OUT is an integer. When all INx where 1≤x≤16 are activated that is = Boolean 1 it
corresponds to that integer 65535 is available on the output OUT. BTIGAPC function is
designed for receiving up to 16 booleans input locally. If the BLOCK input is activated, it will
freeze the output at the last value.
Values of each of the different OUTx from function block BTIGAPC for 1≤x≤16.
The sum of the value on each INx corresponds to the integer presented on the output OUT on
the function block BTIGAPC.
The sum of the numbers in column “Value when activated” when all INx (where 1≤x≤16) are
active that is=1; is 65535. 65535 is the highest boolean value that can be converted to an
integer by the BTIGAPC function block.
11.10.1 Identification
SEMOD167941-2 v2
Integer to boolean 16 conversion function (IB16) is used to transform an integer into a set of 16
binary (logical) signals. It can be used – for example, to connect integer output signals from
one function to binary (logical) inputs to another function. IB16 function does not have a
logical node mapping.
Values of each of the different OUTx from function block IB16 for 1≤x≤16.
The sum of the value on each INx corresponds to the integer presented on the output OUT on
the function block IB16.
The sum of the numbers in column “Value when activated” when all INx (where 1≤x≤16) are
active that is=1; is 65535. 65535 is the highest boolean value that can be converted to an
integer by the IB16 function block.
11.11.1 Identification
SEMOD167944-2 v4
Integer to boolean 16 conversion with logic node representation function (ITBGAPC) is used to
transform an integer into a set of 16 boolean signals. ITBGAPC function can receive an integer
from a station computer – for example, over IEC 61850–8–1. This function is very useful when
the user wants to generate logical commands (for selector switches or voltage controllers) by
inputting an integer number. ITBGAPC function has a logical node mapping in IEC 61850.
The Integer to Boolean 16 conversion with logic node representation function (ITBGAPC) will
transfer an integer with a value between 0 to 65535 communicated via IEC 61850 and
connected to the ITBGAPC function block to a combination of activated outputs OUTx where
1≤x≤16.
The values of the different OUTx are according to the Table 24.
If the BLOCK input is activated, it freezes the logical outputs at the last value.
The sum of the numbers in column “Value when activated” when all OUTx (1≤x≤16) are active
equals 65535. This is the highest integer that can be converted by the ITBGAPC function block.
The function TEIGAPC is used for user-defined logics and it can also be used for different
purposes internally in the IED. An application example is the integration of elapsed time during
the measurement of neutral point voltage or neutral current at earth-fault conditions.
Settable time limits for warning and alarm are provided. The time limit for overflow indication
is fixed to 999999.9 seconds.
The settings tAlarm and tWarning are user settable limits defined in seconds. The achievable
resolution of the settings depends on the level of the values defined.
A resolution of 10 ms can be achieved when the settings are defined within the range
If the values are above this range, the resolution becomes lower due to the 32 bit float
representation
Note that tAlarm and tWarning are independent settings, that is, there is no
check if tAlarm > tWarning.
The function gives the possibility to monitor the level of integer values in the system relative
to each other or to a fixed value. It is a basic arithmetic function that can be used for
monitoring, supervision, interlocking and other logics.
For proper operation of comparison the set value should be set within the range of ± 2 ×109.
EnaAbs: This setting is used to select the comparison type between signed and absolute
values.
RefSource: This setting is used to select the reference source between input and setting for
comparison.
• Input REF: The function will take reference value from input REF
• Set Value: The function will take reference value from setting SetValue
SetValue: This setting is used to set the reference value for comparison when setting
RefSource is selected as SetValue.
The function gives the possibility to monitor the level of real values in the system relative to
each other or to a fixed value. It is a basic arithmetic function that can be used for monitoring,
supervision, interlocking and other logics.
EnaAbs: This setting is used to select the comparison type between signed and absolute
values.
RefSource: This setting is used to select the reference source between input and setting for
comparison.
• Input REF: The function will take reference value from input REF
• Set Value: The function will take reference value from setting SetValue
SetValue: This setting is used to set the reference value for comparison when setting
RefSource is selected as Set Value. If this setting value is less than 0.2% of the set unit then the
output INLOW will never pickup.
RefPrefix: This setting is used to set the unit of the reference value for comparison when
setting RefSource is selected as SetValue. It has 5 unit selections and they are Milli, Unity, Kilo,
Mega and Giga.
EqualBandHigh: This setting is used to set the equal condition high band limit in % of
reference value. This high band limit will act as reset limit for INHIGH output when INHIGH.
EqualBandLow: This setting is used to set the equal condition low band limit in % of reference
value. This low band limit will act as reset limit for INLOW output when INLOW.
For the above condition the comparator can be designed with settings as follows,
EnaAbs = Absolute
SetValue = 100
RefPrefix = Kilo
Operation
The function will set the outputs for the following conditions,
INEQUAL will set when the INPUT is between the ranges of 95 to 105 kA.
INHIGH will set when the INPUT crosses above 105 kA.
If the comparison should be done between two current magnitudes then those current signals
need to be connected to function inputs, INPUT and REF. Then the settings should be adjusted
as below,
EnaAbs = Absolute
Section 12 Monitoring
12.1 Measurement GUID-9D2D47A0-FE62-4FE3-82EE-034BED82682A v1
12.1.1 Identification
SEMOD56123-2 v8
SYMBOL-RR V1 EN-US
SYMBOL-SS V1 EN-US
SYMBOL-UU V1 EN-US
SYMBOL-VV V1 EN-US
SYMBOL-TT V1 EN-US
SYMBOL-UU V1 EN-US
Measurement functions are used for power system measurement, supervision and reporting
to the local HMI, monitoring tool within PCM600 or to station level for example, via IEC 61850.
The possibility to continuously monitor measured values of active power, reactive power,
currents, voltages, frequency, power factor etc. is vital for efficient production, transmission
and distribution of electrical energy. It provides to the system operator fast and easy overview
of the present status of the power system. Additionally, it can be used during testing and
commissioning of protection and control IEDs in order to verify proper operation and
connection of instrument transformers (CTs and VTs). During normal service by periodic
comparison of the measured value from the IED with other independent meters the proper
operation of the IED analog measurement chain can be verified. Finally, it can be used to verify
proper direction orientation for distance or directional overcurrent protection function.
The available measured values from an IED are depending on the actual
hardware (TRM) and the logic configuration made in PCM600.
All measured values can be supervised with four settable limits that is, low-low limit, low limit,
high limit and high-high limit. A zero clamping reduction is also supported, that is, the
measured value below a settable limit is forced to zero which reduces the impact of noise in
the inputs.
Dead-band supervision can be used to report measured signal value to station level when
change in measured value is above set threshold limit or time integral of all changes since the
last time value updating exceeds the threshold limit. Measure value can also be based on
periodic reporting.
The measurement function, CVMMXN, provides the following power system quantities:
,
The measuring functions CMMXU, VMMXU and VNMMXU provide physical quantities:
It is possible to calibrate the measuring function above to get better then class 0.5
presentation. This is accomplished by angle and amplitude compensation at 5, 30 and 100% of
rated current and at 100% of rated voltage.
The power system quantities provided, depends on the actual hardware, (TRM)
and the logic configuration made in PCM600.
The measuring functions CMSQI and VMSQI provide sequence component quantities:
Zero clampings are also handled entirely by ZeroDb separately for each function's every output
signal. For example, zero clamping of U12 is handled by UL12ZeroDb in VMMXU, zero clamping
of I1 is handled by IL1ZeroDb in CMMXU, and so on.
Relevant settings and their values on the local HMI under Main menu/Settings/IED settings/
Monitoring/Servicevalues(P_Q)/CVMMXN(P_Q):
• When system voltage falls below UGenZeroDB, values for S, P, Q, PF, ILAG, ILEAD, U and F
are forced to zero.
• When system current falls below IGenZeroDB, values for S, P, Q, PF, ILAG, ILEAD, U and F
are forced to zero.
• When the value of a single signal falls below its set deadband, the value is forced to zero.
For example, if the apparent three-phase power falls below SZeroDb, the value for S is
forced to zero.
The available setting parameters of the measurement function CVMMXN, CMMXU, VMMXU,
CMSQI, VMSQI, VNMMXU are depending on the actual hardware (TRM) and the logic
configuration made in PCM600.
The parameters for the Measurement functions CVMMXN, CMMXU, VMMXU, CMSQI, VMSQI,
VNMMXU are set via the local HMI or PCM600.
GlobalBaseSel: Selects the global base value group used by the function to define IBase, UBase
and SBase.
Operation: Off/On. Every function instance (CVMMXN, CMMXU, VMMXU, CMSQI, VMSQI,
VNMMXU) can be taken in operation (On) or out of operation (Off).
The following general settings can be set for the Measurement function (CVMMXN).
Mode: Selection of measured current and voltage. There are 9 different ways of calculating
monitored three-phase values depending on the available VT inputs connected to the IED. See
parameter group setting table.
UGenZeroDb: Minimum level of voltage in % of UBase, used as indication of zero voltage (zero
point clamping). If measured value is below UGenZeroDb calculated S, P, Q and PF will be zero.
IGenZeroDb: Minimum level of current in % of IBase, used as indication of zero current (zero
point clamping). If measured value is below IGenZeroDb calculated S, P, Q and PF will be zero.
The following general settings can be set for the Phase current measurement (CMMXU).
The following general settings can be set for the Phase-phase voltage measurement
(VMMXU).
The following general settings can be set for all monitored quantities included in the
functions (CVMMXN, CMMXU, VMMXU, CMSQI, VMSQI, VNMMXU) X in setting names below
equals S, P, Q, PF, U, I, F, IL1-3, UL1-3UL12-31, I1, I2, 3I0, U1, U2 or 3U0.
Xmin: Minimum value for analog signal X set directly in applicable measuring unit. This forms
the minimum limit of the range.
Xmax: Maximum value for analog signal X. This forms the maximum limit of the range.
XZeroDb: Zero point clamping. A signal value less than XZeroDb is forced to zero.
Observe the related zero point clamping settings in Setting group N for CVMMXN
(UGenZeroDb and IGenZeroDb). If measured value is below UGenZeroDb and/or IGenZeroDb
calculated S, P, Q and PF will be zero and these settings will override XZeroDb.
XRepTyp: Reporting type. Cyclic (Cyclic), amplitude deadband (Dead band), integral deadband
(Int deadband) or Deadband and xx se cyclic (xx: 5 sec, 30 sec, 1 min). The reporting interval is
controlled by the parameter XDbRepInt.
XDbRepInt: This setting handles all the reporting types. If setting is deadband in XRepTyp,
XDbRepInt defines the deadband in m% of the measuring range. For cyclic reporting type
(XRepTyp : cyclic), the setting value reporting interval is in seconds. Amplitude deadband is the
setting value in m% of measuring range. Integral deadband setting is the integral area, that is,
measured value in m% of measuring range multiplied by the time between two measured
values.
XHiHiLim: High-high limit. Set as % of YBase (Y is SBase for S,P,Q UBase for Voltage
measurement and IBase for current measurement).
XHiLim: High limit. Set as % of YBase (Y is SBase for S,P,Q UBase for Voltage measurement and
IBase for current measurement).
XLowLim: Low limit. Set as % of YBase (Y is SBase for S,P,Q UBase for Voltage measurement
and IBase for current measurement).
XLowLowLim: Low-low limit. Set as % of YBase (Y is SBase for S,P,Q UBase for Voltage
measurement and IBase for current measurement).
All phase angles are presented in relation to defined reference channel. The parameter
PhaseAngleRef defines the reference.
Calibration curves
It is possible to calibrate the functions (CVMMXN, CMMXU, VMMXU and VNMMXU) to get class
0.5 presentations of currents, voltages and powers. This is accomplished by amplitude and
angle compensation at 5, 30 and 100% of rated current and voltage. The compensation curve
will have the characteristic for amplitude and angle compensation of currents as shown in
figure 69 (example). The first phase will be used as reference channel and compared with the
curve for calculation of factors. The factors will then be used for all related channels.
IEC05000652 V2 EN-US
For each of them detail explanation and final list of selected setting parameters values will be
provided.
The available measured values of an IED are depending on the actual hardware
(TRM) and the logic configuration made in PCM600.
400kV Busbar
1000/1 A
400 0 ,1 IED
/ kV
3 3
P Q
400kV OHL
IEC09000039-3-en.vsdx
IEC09000039-1-EN V3 EN-US
1. Set correctly CT and VT data and phase angle reference channel PhaseAngleRef using
PCM600 for analog input channels
2. Connect, in PCM600, measurement function to three-phase CT and VT inputs
3. Set under General settings parameters for the Measurement function:
• general settings as shown in table 25.
• level supervision of active power as shown in table 26.
• calibration parameters as shown in table 27.
110kV Busbar
200/1
31,5 MVA
110/36,75/(10,5) kV IED
Yy0(d5)
P Q
500/5
UL1L2
35 / 0,1kV
1. Set correctly all CT and VT and phase angle reference channel PhaseAngleRef data using
PCM600 for analog input channels
2. Connect, in PCM600, measurement function to LV side CT & VT inputs
3. Set the setting parameters for relevant Measurement function as shown in the following
table 28:
12.2.1 Identification
GUID-AD96C26E-C3E5-4B21-9ED6-12E540954AC3 v4
Gas medium supervision (SSIMG) is used for monitoring the circuit breaker condition. Proper
arc extinction by the compressed gas in the circuit breaker is very important. When the
pressure becomes too low compared to the required value, the circuit breaker operation shall
be blocked to minimize the risk of internal failure. Binary information based on the gas
pressure in the circuit breaker is used as an input signal to the function. The function
generates alarms based on the received information.
The parameters for Gas medium supervision SSIMG can be set via local HMI or Protection and
Control Manager PCM600.
Operation: This is used to disable/enable the operation of gas medium supervision i.e. Off/On.
PresAlmLimit: This is used to set the limit for a pressure alarm condition in the circuit breaker.
PresLOLimit: This is used to set the limit for a pressure lockout condition in the circuit breaker.
TempAlarmLimit: This is used to set the limit for a temperature alarm condition in the circuit
breaker.
TempLOLimit: This is used to set the limit for a temperature lockout condition in the circuit
breaker.
tPressureAlarm: This is used to set the time delay for a pressure alarm indication, given in s.
tPressureLO: This is used to set the time delay for a pressure lockout indication, given in s.
tTempAlarm: This is used to set the time delay for a temperature alarm indication, given in s.
tTempLockOut: This is used to set the time delay for a temperature lockout indication, given in
s.
tResetPressAlm: This is used for the pressure alarm indication to reset after a set time delay in
s.
tResetPressLO: This is used for the pressure lockout indication to reset after a set time delay
in s.
tResetTempLO: This is used for the temperature lockout indication to reset after a set time
delay in s.
tResetTempAlm: This is used for the temperature alarm indication to reset after a set time
delay in s.
12.3.1 Identification
GUID-4CE96EF6-42C6-4F2E-A190-D288ABF766F6 v3
Liquid medium supervision (SSIML) is used for monitoring the oil insulated device condition.
For example, transformers, shunt reactors, and so on. When the level becomes too low
compared to the required value, the operation is blocked to minimize the risk of internal
failures. Binary information based on the oil level in the oil insulated devices are used as input
signals to the function. In addition, the function generates alarms based on the received
information.
The parameters for Liquid medium supervision SSIML can be set via local HMI or Protection
and Control Manager PCM600.
Operation: This is used to disable/enable the operation of liquid medium supervision i.e.
Off/On.
LevelAlmLimit: This is used to set the limit for a level alarm condition in the oil insulated
device.
LevelLOLimit: This is used to set the limit for a level lockout condition in the oil insulated
device.
TempAlarmLimit: This is used to set the limit for a temperature alarm condition in the oil
insulated device.
TempLOLimit: This is used to set the limit for a temperature lockout condition in the oil
insulated device.
tLevelAlarm: This is used to set the time delay for a level alarm indication, given in s.
tLevelLockOut: This is used to set the time delay for a level lockout indication, given in s.
tTempAlarm: This is used to set the time delay for a temperature alarm indication, given in s.
tTempLockOut: This is used to set the time delay for a temperature lockout indication, given in
s.
tResetLevelAlm: This is used for the level alarm indication to reset after a set time delay in s.
tResetLevelLO: This is used for the level lockout indication to reset after a set time delay in s.
tResetTempLO: This is used for the temperature lockout indication to reset after a set time
delay in s.
tResetTempAlm: This is used for the temperature alarm indication to reset after a set time
delay in s.
The circuit breaker maintenance is usually based on regular time intervals or the number of
operations performed. This has some disadvantages because there could be a number of
abnormal operations or few operations with high-level currents within the predetermined
maintenance interval. Hence, condition-based maintenance scheduling is an optimum solution
in assessing the condition of circuit breakers.
100000
50000
P1
20000
10000
Number of make-break operations ( n)
5000
2000
1000
500
200
P2
100
50
20
10
0.1 0.2 0.5 1 2 5 10 20 50 100
IEC12000623_1_en.vsd
IEC12000623 V1 EN-US
Figure 72: An example for estimating the remaining life of a circuit breaker
Calculation for estimating the remaining life
The graph shows that there are 10000 possible operations at the rated operating current and
900 operations at 10 kA and 50 operations at rated fault current. Therefore, if the interrupted
current is 10 kA, one operation is equivalent to 10000/900 = 11 operations at the rated current.
It is assumed that prior to tripping, the remaining life of a breaker is 10000 operations.
Remaining life calculation for three different interrupted current conditions is explained below.
• Breaker interrupts at and below the rated operating current, that is, 2 kA, the remaining
life of the CB is decreased by 1 operation and therefore, 9999 operations remaining at the
rated operating current.
• Breaker interrupts between rated operating current and rated fault current, that is, 10 kA,
one operation at 10kA is equivalent to 10000/900 = 11 operations at the rated current. The
remaining life of the CB would be (10000 – 10) = 9989 at the rated operating current after
one operation at 10 kA.
• Breaker interrupts at and above rated fault current, that is, 50 kA, one operation at 50 kA
is equivalent to 10000/50 = 200 operations at the rated operating current. The remaining
life of the CB would become (10000 – 200) = 9800 operations at the rated operating
current after one operation at 50 kA.
Accumulated energy
Monitoring the contact erosion and interrupter wear has a direct influence on the required
maintenance frequency. Therefore, it is necessary to accurately estimate the erosion of the
contacts and condition of interrupters using cumulative summation of Iy. The factor "y"
depends on the type of circuit breaker. The energy values were accumulated using the current
value and exponent factor for CB contact opening duration. When the next CB opening
operation is started, the energy is accumulated from the previous value. The accumulated
energy value can be reset to initial accumulation energy value by using the Reset accumulating
energy input, RSTIPOW.
The breaker monitoring function is used to monitor different parameters of the circuit
breaker. The breaker requires maintenance when the number of operations has reached a
predefined value. For proper functioning of the circuit breaker, it is also essential to monitor
the circuit breaker operation, spring charge indication or breaker wear, travel time, number of
operation cycles and accumulated energy during arc extinction.
The parameters for breaker monitoring (SSCBR) can be set via the local HMI or Protection and
Control Manager (PCM600).
Common base IED values for primary current (IBase), primary voltage (UBase) and primary
power (SBase) are set in Global base values for settings function GBASVAL.
Operation: On or Off.
IBase: Base phase current in primary A. This current is used as reference for current settings.
CurrExponent: Current exponent setting for energy calculation. It varies for different types of
circuit breakers. This factor ranges from 0.5 to 3.0.
AccStopCurr: RMS current setting below which calculation of energy accumulation stops. It is
given as a percentage of IBase.
ContTrCorr: Correction factor for time difference in auxiliary and main contacts' opening time.
OperTimeDelay: Time delay between change of status of trip output and start of main contact
separation.
12.5.1 Identification
SEMOD167950-2 v2
When using a Substation Automation system with LON or SPA communication, time-tagged
events can be sent at change or cyclically from the IED to the station level. These events are
created from any available signal in the IED that is connected to the Event function (EVENT).
The EVENT function block is used for LON and SPA communication.
Analog, integer and double indication values are also transferred through the EVENT function.
M12811-3 v3
The input parameters for the Event function (EVENT) can be set individually via the local HMI
(Main Menu/Settings / IED Settings / Monitoring / Event Function) or via the Parameter
Setting Tool (PST).
• NoEvents
• OnSet, at pick-up of the signal
• OnReset, at drop-out of the signal
• OnChange, at both pick-up and drop-out of the signal
• AutoDetect, the EVENT function makes the reporting decision (reporting criteria for
integers have no semantic, prefer to be set by the user)
• Off
• Channel 1-8
• Channel 9-16
• Channel 1-16
It is important to set the time interval for cyclic events in an optimized way to
minimize the load on the station bus.
12.6.1 Identification
M16055-1 v9
To get fast, complete and reliable information about disturbances in the primary and/or in the
secondary system it is very important to gather information on fault currents, voltages and
events. It is also important having a continuous event-logging to be able to monitor in an
overview perspective. These tasks are accomplished by the disturbance report function
DRPRDRE and facilitate a better understanding of the power system behavior and related
primary and secondary equipment during and after a disturbance. An analysis of the recorded
data provides valuable information that can be used to explain a disturbance, basis for change
of IED setting plan, improve existing equipment, and so on. This information can also be used
in a longer perspective when planning for and designing new installations, that is, a
disturbance recording could be a part of Functional Analysis (FA).
Disturbance report DRPRDRE, always included in the IED, acquires sampled data of all selected
analog and binary signals connected to the function blocks that is,
Disturbance report function is a common name for several functions; Indications (IND), Event
recorder (ER), Event list (EL), Trip value recorder (TVR), Disturbance recorder (DR).
Every disturbance report recording is saved in the IED. The same applies to all events, which
are continuously saved in a ring-buffer. Local HMI can be used to get information about the
recordings, and the disturbance report files may be uploaded in the PCM600 using the
Disturbance handling tool, for report reading or further analysis (using WaveWin, that can be
found on the PCM600 installation CD). The user can also upload disturbance report files using
FTP or MMS (over 61850–8–1) clients.
If the IED is connected to a station bus (IEC 61850-8-1), the disturbance recorder (record made
and fault number) and the fault locator information are available. The same information is
obtainable if IEC 60870-5-103 is used.
M12179-64 v9
The setting parameters for the Disturbance report function DRPRDRE are set via the local HMI
or PCM600.
It is possible to handle up to 40 analog and 352 binary signals, either internal signals or signals
coming from external inputs. The binary signals are identical in all functions that is,
Disturbance recorder (DR), Event recorder (ER), Indication (IND), Trip value recorder (TVR) and
Event list (EL) function.
User-defined names of binary and analog input signals are set using PCM600. The analog and
binary signals appear with their user-defined names. The name is used in all related functions
(Disturbance recorder (DR), Event recorder (ER), Indication (IND), Trip value recorder (TVR) and
Event list (EL)).
Figure 73 shows the relations between Disturbance report, included functions and function
blocks. Event list (EL), Event recorder (ER) and Indication (IND) uses information from the
binary input function blocks (BxRBDR). Trip value recorder (TVR) uses analog information from
the analog input function blocks (AxRADR). Disturbance report function acquires information
from both AxRADR and BxRBDR.
DRPRDRE
Analog signals
Trip value rec
BxRBDR Disturbance
recorder
Binary signals
Event list
Event recorder
Indications
IEC09000337-3-en.vsdx
IEC09000337 V3 EN-US
Three LED indications placed above the LCD screen makes it possible to get quick status
information about the IED.
Green LED:
Steady light In Service
Flashing light Internal failure
Dark No power supply
Yellow LED:
Steady light Triggered on binary signal N with SetLEDx = Start (or Start
and Trip)
Flashing light The IED is in test mode
Red LED:
Steady light Triggered on binary signal N with SetLEDx = Trip (or Start
and Trip)
Flashing The IED is in configuration mode
Operation M12179-82 v7
The operation of Disturbance report function DRPRDRE has to be set On or Off. If Off is
selected, note that no disturbance report is registered, and none sub-function will operate
(the only general parameter that influences Event list (EL)).
Operation = Off:
Operation = On:
• Disturbance reports are stored, disturbance data can be read from the local HMI and from
a PC for example using PCM600.
• LED information (yellow - start, red - trip) is stored.
Every recording will get a number (0 to 999) which is used as identifier (local HMI, disturbance
handling tool and IEC 61850). An alternative recording identification is date, time and
sequence number. The sequence number is automatically increased by one for each new
recording and is reset to zero at midnight. The maximum number of recordings stored in the
IED is 100. The oldest recording will be overwritten when a new recording arrives (FIFO).
The IED flash disk should NOT be used to store any user files. This might cause
disturbance recordings to be deleted due to lack of disk space.
The different recording times for Disturbance report are set (the pre-fault time, post-fault
time, and limit time). These recording times affect all sub-functions more or less but not the
Event list (EL) function.
Prefault recording time (PreFaultRecT) is the recording time before the starting point of the
disturbance. The setting should be at least 0.1 s to ensure enough samples for the estimation
of pre-fault values in the Trip value recorder (TVR) function.
Postfault recording time (PostFaultRecT) is the maximum recording time after the
disappearance of the trig-signal (does not influence the Trip value recorder (TVR) function).
Recording time limit (TimeLimit) is the maximum recording time after trig. The parameter
limits the recording time if some trigging condition (fault-time) is very long or permanently set
(does not influence the Trip value recorder (TVR) function).
If the IED is in test mode and OpModeTest = On. Disturbance report function works in normal
mode and the status is indicated in the saved recording.
In order to capture the new disturbance it is possible to allow retriggering (PostRetrig = On)
during the post-fault time. In this case a new, complete recording will start and, during a
period, run in parallel with the initial recording.
When the retrig parameter is disabled (PostRetrig = Off), a new recording will not start until
the post-fault (PostFaultrecT or TimeLimit) period is terminated. If a new trig occurs during
the post-fault period and lasts longer than the proceeding recording a new complete
recording will be started.
Up to 352 binary signals can be selected among internal logical and binary input signals. The
configuration tool is used to configure the signals.
For each of the 352 signals, it is also possible to select if the signal is to be used as a trigger
for the start of the Disturbance report and if the trigger should be activated on positive (1) or
negative (0) slope.
OperationN: Disturbance report may trig for binary input N (On) or not (Off).
TrigLevelN: Trig on positive (Trig on 1) or negative (Trig on 0) slope for binary input N.
Func103N: Function type number (0-255) for binary input N according to IEC-60870-5-103, that
is, 128: Distance protection, 160: overcurrent protection, 176: transformer differential
protection and 192: line differential protection.
Info103N: Information number (0-255) for binary input N according to IEC-60870-5-103, that is,
69-71: Trip L1-L3, 78-83: Zone 1-6.
Up to 40 analog signals can be selected among internal analog and analog input signals.
PCM600 is used to configure the signals.
The analog trigger of Disturbance report is not affected if analog input M is to be included in
the disturbance recording or not (OperationM = On/Off).
If OperationM = Off, no waveform (samples) will be recorded and reported in graph. However,
Trip value, pre-fault and fault value will be recorded and reported. The input channel can still be
used to trig the disturbance recorder.
If OperationM = On, waveform (samples) will also be recorded and reported in graph.
OverTrigOpM, UnderTrigOpM: Over or Under trig operation, Disturbance report may trig for
high/low level of analog input M (On) or not (Off).
OverTrigLeM, UnderTrigLeM: Over or under trig level, Trig high/low level relative nominal value
for analog input M in percent of nominal value.
Indications M12179-448 v4
IndicationMaN: Indication mask for binary input N. If set (Show), a status change of that
particular input, will be fetched and shown in the disturbance summary on local HMI. If not set
(Hide), status change will not be indicated.
SetLEDN: Set red LED on local HMI in front of the IED if binary input N changes status.
If OperationM = Off, no waveform (samples) will be recorded and reported in graph. However,
Trip value, pre-fault and fault value will be recorded and reported. The input channel can still be
used to trig the disturbance recorder.
If OperationM = On, waveform (samples) will also be recorded and reported in graph.
The density of recording equipment in power systems is increasing, since the number of
modern IEDs, where recorders are included, is increasing. This leads to a vast number of
recordings at every single disturbance and a lot of information has to be handled if the
recording functions do not have proper settings. The goal is to optimize the settings in each
IED to be able to capture just valuable disturbances and to maximize the number that is
possible to save in the IED.
The recording time should not be longer than necessary (PostFaultrecT and TimeLimit).
• Should the function record faults only for the protected object or cover more?
• How long is the longest expected fault clearing time?
• Is it necessary to include reclosure in the recording or should a persistent fault generate a
second recording (PostRetrig)?
• Binary signals: Use only relevant signals to start the recording that is, protection trip,
carrier receive and/or start signals.
• Analog signals: The level triggering should be used with great care, since unfortunate
settings will cause enormously number of recordings. If nevertheless analog input
triggering is used, chose settings by a sufficient margin from normal operation values.
Phase voltages are not recommended for trigging.
There is a risk of flash wear out if the disturbance report triggers too often.
Remember that values of parameters set elsewhere are linked to the information on a report.
Such parameters are, for example, station and object identifiers, CT and VT ratios.
The Logical signal status report (BINSTATREP) function makes it possible to poll signals from
various other function blocks.
BINSTATREP has 16 inputs and 16 outputs. The output status follows the inputs and can be
read from the local HMI or via SPA communication.
When an input is set, the respective output is set for a user defined time. If the input signal
remains set for a longer period, the output will remain set until the input signal resets.
INPUTn
OUTPUTn
t t
IEC09000732-1-en.vsd
IEC09000732 V1 EN-US
The pulse time t is the only setting for the Logical signal status report (BINSTATREP). Each
output can be set or reset individually, but the pulse time will be the same for all outputs in the
entire BINSTATREP function.
12.8.1 Identification
GUID-F3FB7B33-B189-4819-A1F0-8AC7762E9B7E v3
Limit counter (L4UFCNT) is intended for applications where positive and/or negative flanks on
a binary signal need to be counted.
The limit counter provides four independent limits to be checked against the accumulated
counted value. The four limit reach indication outputs can be utilized to initiate proceeding
actions. The output indicators remain high until the reset of the function.
It is also possible to initiate the counter from a non-zero value by resetting the function to the
wanted initial value provided as a setting.
If applicable, the counter can be set to stop or rollover to zero and continue counting after
reaching the maximum count value. The steady overflow output flag indicates the next count
after reaching the maximum count value. It is also possible to set the counter to rollover and
indicate the overflow as a pulse, which lasts up to the first count after rolling over to zero. In
this case, periodic pulses will be generated at multiple overflow of the function.
GUID-DA5DA8D7-4821-4BFB-86CC-28658E376270 v2
The parameters for Limit counter L4UFCNT are set via the local HMI or PCM600.
The function is used for user-defined logics and it can also be used for different purposes
internally in the IED. An application example is to accumulate the total running/energized time
of the generator, transformer, reactor, capacitor bank or even line.
Settable time limits for warning and alarm are provided. The time limit for overflow indication
is fixed to 99999.9 hours. At overflow the accumulated time resets and the accumulation
starts from zero again.
The settings tAlarm and tWarning are user settable limits defined in hours. The achievable
resolution of the settings is 0.1 hours (6 minutes).
tAlarm and tWarning are independent settings, that is, there is no check if
tAlarm > tWarning.
Section 13 Metering
13.1 Pulse-counter logic PCFCNT IP14600-1 v3
13.1.1 Identification
M14879-1 v4
S00947 V1 EN-US
Pulse-counter logic (PCFCNT) function counts externally generated binary pulses, for instance
pulses coming from an external energy meter, for calculation of energy consumption values.
The pulses are captured by the binary input module (BIM), and read by the PCFCNT function.
The number of pulses in the counter is then reported via the station bus to the substation
automation system or read via the station monitoring system as a service value. When using
IEC 61850–8–1, a scaled service value is available over the station bus.
The normal use for this function is the counting of energy pulses from external energy meters.
An optional number of inputs from an arbitrary input module in IED can be used for this
purpose with a frequency of up to 40 Hz. The pulse-counter logic PCFCNT can also be used as a
general purpose counter.
Parameters that can be set individually for each pulse counter from PCM600:
• Operation: Off/On
• tReporting: 0-3600s
• EventMask: NoEvents/ReportEvents
On the Binary input module (BIM), the debounce filter default time is set to 5ms, that is, the
counter suppresses pulses with a pulse length less than 5 ms. The input oscillation blocking
frequency is preset to 40 Hz meaning that the counter detects the input to oscillate if the
input frequency is greater than 40 Hz. Oscillation suppression is released at 30 Hz. Block/
release values for oscillation can be changed on the local HMI and PCM600 under Main menu/
Configuration/I/O modules.
The setting is common for all input channels on BIM, that is, if limit changes are
made for inputs not connected to the pulse counter, the setting also influences
the inputs on the same board used for pulse counting.
13.2.1 Identification
SEMOD175537-2 v4
Energy calculation and demand handling function (ETPMMTR) is intended for statistics of the
forward and reverse active and reactive energy. It has a high accuracy basically given by the
measurements function (CVMMXN). This function has a site calibration possibility to further
increase the total accuracy.
The function is connected to the instantaneous outputs of (CVMMXN) as shown in figure 75.
ETPMMTR
CVMMXN
P_ INST P
Q_ INST Q
STARTACC
STOPACC
RSTACC
RSTDMD
IEC130 00190-2-en.vsdx
IEC13000190 V2 EN-US
Figure 75: Connection of energy calculation and demand handling function ETPMMTR to
the measurements function (CVMMXN)
The energy values can be read through communication in MWh and MVArh in monitoring tool
of PCM600 and/or alternatively the values can be presented on the local HMI. The local HMI
graphical display is configured with PCM600 Graphical Display Editor tool (GDE) with a
measuring value which is selected to the active and reactive component as preferred. Also all
Accumulated Active Forward, Active Reverse, Reactive Forward and Reactive Reverse energy
values can be presented.
Maximum demand values are presented in MWh or MVArh in the same way.
Alternatively, the energy values can be presented with use of the pulse counters function
(PCGGIO). The output energy values are scaled with the pulse output setting values
EAFAccPlsQty, EARAccPlsQty, ERFAccPlsQty and ERVAccPlsQty of the energy metering
function and then the pulse counter can be set-up to present the correct values by scaling in
this function. Pulse counter values can then be presented on the local HMI in the same way
and/or sent to the SA (Substation Automation) system through communication where the
total energy then is calculated by summation of the energy pulses. This principle is good for
very high values of energy as the saturation of numbers else will limit energy integration to
about one year with 50 kV and 3000 A. After that the accumulation will start on zero again.
The following settings can be done for the energy calculation and demand handling function
ETPMMTR:
GlobalBaseSel: Selects the global base value group used by the function to define IBase, UBase
and SBase.
Operation: Off/On
tEnergyOnPls: gives the pulse length ON time of the pulse. It should be at least 100 ms when
connected to the Pulse counter function block. Typical value can be 100 ms.
tEnergyOffPls: gives the OFF time between pulses. Typical value can be 100 ms.
EAFAccPlsQty and EARAccPlsQty: gives the MWh value in each pulse. It should be selected
together with the setting of the Pulse counter (PCGGIO) settings to give the correct total pulse
value.
ERFAccPlsQty and ERVAccPlsQty : gives the MVArh value in each pulse. It should be selected
together with the setting of the Pulse counter (PCGGIO) settings to give the correct total pulse
value.
For the advanced user there are a number of settings for direction, zero clamping, max limit,
and so on. Normally, the default values are suitable for these parameters.
The access points are used to connect the IED to the communication buses (like the station
bus) that use communication protocols. The access point can be used for single and
redundant data communication. The access points are also used for communication with the
merging units and for time synchronization using Precision Time Protocol (PTP).
The physical ports allocated to access points 2–4 have to be added in the
hardware tool in PCM600 before the access points can be configured. The
factory setting only includes the physical ports allocated to the front port and
access point 1.
The settings for the access points are configured using the Ethernet configuration tool (ECT)
in PCM600.
The access point is activated if the Operation checkbox is checked for the respective access
point and a partial or common write to IED is performed.
Redundancy and PTP cannot be set for the front port (Access point 0) as redundant
communication and PTP are only available for the rear optical Ethernet ports.
Subnetwork shows the SCL subnetwork to which the access point is connected. This column
shows the SCL subnetworks available in the PCM600 project. SCL subnetworks can be
created/deleted in the Subnetworks tab of IEC 61850 Configuration tool in PCM600.
When saving the ECT configuration after selecting a subnetwork, ECT creates
the access point in the SCL model. Unselecting the subnetwork removes the
access point from the SCL model. This column is editable for IEC61850 Ed2 IEDs
and not editable for IEC61850 Ed1 IEDs because in IEC61850 Ed1 only one
access point can be modelled in SCL.
The IP address can be set in IP address. ECT validates the value, the access points have to be
on separate subnetworks.
The subnetwork mask can be set in Subnet mask. This field will be updated to the SCL model
based on the Subnetwork selection.
To select which communication protocols can be run on the respective access points, check or
uncheck the check box for the relevant protocol. The protocols are not activated/deactivated
in ECT, only filtered for the specific access point. For information on how to activate the
individual communication protocols, see the communication protocol chapters.
The default gateway can be selected by entering the IP address in Default gateway. The default
gateway is the router that is used to communicate with the devices in the other subnetwork.
By default this is set to 0.0.0.0 which means that no default gateway is selected. ECT validates
the entered value, but the default gateway has to be in the same subnetwork as the access
point. The default gateway is the router that is being used as default, that is when no route
has been set up for the destination. If communication with a device in another subnetwork is
needed, a route has to be set up. For more information on routes, see the Routes chapter in
the Technical manual and the Application manual.
DHCP can be activated for the front port from the LHMI in Main menu/Configuration/
Communication/Ethernet configuration/Front port/DHCP:1
14.2.1 Identification
GUID-B7AE0374-0336-42B8-90AF-3AE1C79A4116 v1
Dynamic access point diagnostic (RCHLCCH) is used to supervise and assure redundant
Ethernet communication over two channels. This will secure data transfer even though one
communication channel might not be available for some reason
Parallel Redundancy Protocol (PRP) and High-availability Seamless Redundancy (HSR) provides
redundant communication over station bus running the available communication protocols.
The redundant communication uses two Ethernet ports.
Device 1 Device 2
AP1 AP1
PhyPortA PhyPortB PhyPortA PhyPortB
Switch A Switch B
Device 3 Device 4
IEC09000758-4-en.vsd
IEC09000758 V4 EN-US
Device 1 Device 2
AP1 AP1
PhyPortA PhyPortB PhyPortA PhyPortB
Device 3 Device 4
IEC16000038-1-en.vsdx
IEC16000038 V1 EN-US
Redundancy: redundant communication is activated when the parameter is set to PRP-0, PRP-1
or HSR. The settings for the next access point will be hidden and PhyPortB will show the
second port information. Redundant communication is activated after a common write to IED
is done.
PRP-1 should be used primarily, PRP-0 is intended only for use in existing PRP-networks. PRP-1
and HSR can be combined in a mixed network.
If the access point is not taken into operation, the write option in Ethernet Configuration Tool
can be used to activate the access point.
IEC16000039-1-en.vsdx
IEC16000039 V1 EN-US
Figure 78: ECT screen with Redundancy set to PRP-1 on Access point 1 and HSR Access
point 3
The merging units (MU) are called so because they can gather analog values from one or more
measuring transformers, sample the data and send the data over process bus to other clients
(or subscribers) in the system. Some merging units are able to get data from classical
measuring transformers, others from non-conventional measuring transducers and yet others
can pick up data from both types.
IEC17000044-1-en.vsdx
IEC17000044 V1 EN-US
For information on the merging unit setting guidelines, see section IEC/UCA 61850-9-2LE
communication protocol.
14.4 Routes
The route specifies that when a package is sent to the destination device it should be sent
through the selected router. If no route is specified the source device will not find the
destination device.
Operation for the route can be set to On/Off by checking and unchecking the check-box in the
operation column.
Each IED is provided with several communication interfaces enabling it to connect to one or
many substation level systems or equipment, either on the Substation Automation (SA) bus or
Substation Monitoring (SM) bus.
M13912-3 v4
IEC 61850-8-1 communication protocol allows vertical communication to HSI clients and allows
horizontal communication between two or more intelligent electronic devices (IEDs) from one
or several vendors to exchange information and to use it in the performance of their functions
and for correct co-operation.
GOOSE (Generic Object Oriented Substation Event), which is a part of IEC 61850–8–1 standard,
allows the IEDs to communicate state and control information amongst themselves, using a
publish-subscribe mechanism. That is, upon detecting an event, the IED(s) use a multi-cast
transmission to notify those devices that have registered to receive the data. An IED can, by
publishing a GOOSE message, report its status. It can also request a control action to be
directed at any device in the network.
M13913-3 v6
Figure 80 shows the topology of an IEC 61850–8–1 configuration. IEC 61850–8–1 specifies only
the interface to the substation LAN. The LAN itself is left to the system integrator.
Engineering
Station HSI
Workstation Gateway
Base System
SMS
CC
Printer
IEC09000135_en.v
sd
IEC09000135 V1 EN-US
Station HSI
MicroSCADA
Gateway
GOOSE
GOOSEPortEd1: Selection of the Ethernet link where GOOSE traffic shall be sent and received.
This is only valid for Edition 1 and can be ignored if Edition 2 is used. For Edition 2, the
Ethernet link selection is done with the Ethernet Configuration Tool (ECT) in PCM600.
In addition to the data object and data attributes of the logical nodes, it is possible to send
the outputs of the function blocks using the generic communication blocks. The outputs of
this function can be set in a dataset and be sent in a GOOSE Control Block to other subscriber
IEDs. There are different function blocks for different type of sending data.
Generic communication function for Single Point indication SPGAPC, SP16GAPC SEMOD55999-1 v4
Application SEMOD55350-5 v8
Generic communication function for Single Point Value (SPGAPC) function is used to send one
single logical output to other systems or equipment in the substation. SP16GAPC can be used
to send up to 16 single point values from the application functions running in the same cycle
time. SPGAPC has one visible input and SPGAPC16 has 16 visible inputs that should be
connected in the ACT tool.
The high and low limit settings provides limits for the high-high-, high, normal, low and low-
low ranges of the measured value. The actual range of the measured value is shown on the
range output of MVGAPC function block. When a Measured value expander block (RANGE_XP)
is connected to the range output, the logical outputs of the RANGE_XP are changed
accordingly.
The GOOSE data must be received at function blocks. There are different GOOSE receiving
function blocks depending on the type of the received data. Refer to the Engineering manual
for more information about how to configure GOOSE.
Application GUID-808177B7-02CA-40DF-B41B-8B580E38478B v1
The GOOSE receive function blocks are used to receive subscribed data from the GOOSE
protocol. The validity of the data value is exposed as outputs of the function block as well as
the validity of the communication. It is recommended to use these outputs to ensure that only
valid data is handled on the subscriber IED. An example could be to control the external
reservation before operating on a bay. In the figure below, the GOOSESPRCV is used to receive
the status of the bay reservation. The validity of the received data is used in additional logic to
guarantee that the value has good quality before operation on that bay.
Figure 82: GOOSESPRCV and AND function blocks - checking the validity of the received
data
SEMOD166590-5 v7
Every IED can be provided with communication interfaces enabling it to connect to the
process buses in order to get data from analog data acquisition units close to the process
(primary apparatus), commonly known as Merging Units (MU). The protocol used in this case is
the IEC/UCA 61850-9-2LE communication protocol.
The IEC/UCA 61850-9-2LE standard does not specify the quality of the sampled values. Thus,
the accuracy of the current and voltage inputs to the merging unit and the inaccuracy added
by the merging unit must be coordinated with the requirement for the actual type of
protection function.
Factors influencing the accuracy of the sampled values from the merging unit are, for example,
anti aliasing filters, frequency range, step response, truncating, A/D conversion inaccuracy,
time tagging accuracy etc.
In principle, the accuracy of the current and voltage transformers, together with the merging
unit, will have the same quality as the direct input of currents and voltages.
The process bus physical layout can be arranged in several ways, described in Annex B of the
standard, depending on what are the needs for sampled data in a substation.
IEC 6185 0
Gateway
IEC18000011-1-en.vsdx
IEC18000011 V1 EN-US
Figure 83: Example of a station configuration with separated process bus and station
bus
The IED can get analog values simultaneously from a classical CT or VT and from a Merging
Unit, like in this example:
The merging units (MU) are called so because they can gather analog values from one or more
measuring transformers, sample the data and send the data over process bus to other clients
(or subscribers) in the system. Some merging units are able to get data from classical
measuring transformers, others from non-conventional measuring transducers and yet others
can pick up data from both types. The electronic part of a non-conventional measuring
transducer (like a Rogowski coil or a capacitive divider) can represent a MU by itself as long as
it can send sampled data over process bus.
IEC61850-8-1
Splitter
Electrical-to-
Optical Converter
IEC61850-8-1
110 V
Other 1A IED 1PPS
Relays 1A
IEC61850-9-2LE
Ethernet Switch
IEC61850-9-2LE
ABB
1PPS
Merging
Unit
Combi
CT CT
Sensor
Conventional VT
en08000069-3.vsd
IEC08000069 V2 EN-US
Figure 84: Example of a station configuration with the IED receiving analog values from
both classical measuring transformers and merging units.
When a merging unit goes faulty while the bay is in service, the protection functions connected
to that merging unit get blocked. Also, protection functions configured in a 1 1/2 circuit
breaker applications, where two SV streams from different merging units are combined get
blocked. Thus, this has no effect on protection functions in a 1 1/2 circuit breaker
configuration.
This can be resolved by connecting external binary input signals to the BLOCK input on the
respective SMAI function blocks with the use of ACT. When the BLOCK input on a SMAI
function is energized, the SMAI function delivers a magnitude of zero with good quality for all
the channels. Thus, this has no effect on a busbar protection, nor protections in an 1 1/2 circuit
breaker configuration.
SMAI function blocks exist in different cycle times, and all the SMAI blocks that
receive SV streams from the merging units must have the block input signal
configured in the same way to get the correct behavior.
GUID-F723C815-3A26-481A-B046-21D1243E7080 V1 EN-US
Figure 85: Configuration of current inputs using SMAIs in a 1 1/2 circuit breaker
application.
When a bay need maintenance and has energized merging unit connected, it is always a risk to
get unplanned interruptions in the auxiliary power supply which may lead to unwanted
blocking of protections.
This can be resolved by using the same ACT configuration recommendations and procedures
as described in section Faulty merging unit for bay in service.
The process bus communication IEC/UCA 61850-9-2LE has specific settings, similar to the
analog inputs modules.
If there are more than one sample group involved, time synch is mandatory. If there is no time
synchronization, the protection functions will be blocked due to condition blocking.
CTStarPointx: These parameters specify the direction to or from object. See also section
"Setting of current channels".
SyncLostMode: If this parameter is set to Block and the IED hardware time synchronization is
lost or the synchronization to the MU time is lost, the protection functions in the list "" will be
blocked due to conditional blocking. If this parameter is set to BlockOnLostUTC, the
protection functions in list "" are blocked if the IED hardware time synchronization is lost or
the synchronization of the MU time is lost or the IED has lost global common synchronization
(i.e. GPS, IRIG-B or PTP). SYNCH output will be set if IED hardware time synchronization is lost.
MUSYNCH output will be set if either of MU or IED hardware time synchronization is lost.
Binary signals over LDCM are transmitted as valid and processed normally even
when analog signals are transmitted as invalid due to loss of communication or
loss of time synchronization.
Table 29: Blocked protection functions if IEC/UCA 61850-9-2LE communication is interrupted and functions
are connected to specific MUs
Function description IEC 61850 identification Function description IEC 61850 identification
Accidental energizing AEGPVOC Two step overvoltage OV2PTOV
protection for protection
synchronous generator
Broken conductor check BRCPTOC Four step single phase PH4SPTOC
overcurrent protection
Capacitor bank CBPGAPC Radial feeder protection PAPGAPC
protection
Pole discordance CCPDSC Instantaneous phase PHPIOC
protection overcurrent protection
Breaker failure CCRBRF PoleSlip/Out-of-step PSPPPAM
protection protection
Breaker failure CCSRBRF Restricted earth fault REFPDIF
protection, single phase protection, low
version impedance
Current circuit CCSSPVC Two step residual ROV2PTOV
supervison overvoltage protection
Compensated over- and COUVGAPC Rate-of-change SAPFRC
undervoltage protection frequency protection
General currrent and CVGAPC Overfrequency SAPTOF
voltage protection protection
Table continues on next page
Function description IEC 61850 identification Function description IEC 61850 identification
Current reversal and ECRWPSCH Underfrequency SAPTUF
weakend infeed logic for protection
residual overcurrent
protection
Four step residual EF4PTOC Sudden change in SCCVPTOC
overcurrent protection current variation
Instantaneous residual EFPIOC Sensitive Directional SDEPSDE
overcurrent protection residual over current and
power protetcion
Phase selection, FDPSPDIS Synchrocheck, energizing SESRSYN
quadrilateral check, and synchronizing
characteristic with fixed
angle
Faulty phase FMPSPDIS Circuit breaker condition SSCBR
identification with load monitoring
enchroachment
Phase selection, FRPSPDIS Insulation gas SSIMG
quadrilateral monitoring
characteristic with
settable angle
Frequency time FTAQFVR Insulation liquid SSIML
accumulation protection monitoring
Fuse failure supervision FUFSPVC Stub protection STBPTOC
Generator differential GENPDIF Transformer differential T2WPDIF
protection protection, two winding
Directional Overpower GOPPDOP Transformer differential T3WPDIF
protection protection, three
winding
Generator rotor overload GRPTTR Automatic voltage TR1ATCC
protection control for tapchanger,
single control
Generator stator GSPTTR Automatic voltage TR8ATCC
overload protection control for tapchanger,
parallel control
Directional Underpower GUPPDUP Thermal overload TRPTTR
protection protection, two time
constants
1Ph High impedance HZPDIF Two step undervoltage UV2PTUV
differential protection protection
Line differential L3CPDIF Voltage differential VDCPTOV
protection, 3 CT sets, 2-3 protection
line ends
Line differential L6CPDIF Fuse failure supervision VDRFUF
protection, 6 CT sets, 3-5
line ends
Low active power and LAPPGAPC Voltage-restrained time VRPVOC
power factor protection overcurrent protection
Negative sequence LCNSPTOC Local acceleration logic ZCLCPSCH
overcurrent protection
Negative sequence LCNSPTOV Scheme communication ZCPSCH
overvoltage protection logic for distance or
overcurrent protection
Three phase overcurrent LCP3PTOC Current reversal and ZCRWPSCH
weak-end infeed logic for
distance protection
Table continues on next page
Function description IEC 61850 identification Function description IEC 61850 identification
Three phase LCP3PTUC Automatic switch onto ZCVPSOF
undercurrent fault logic, voltage and
current based
Thermal overload LCPTTR Under impedance ZGVPDIS
protection, one time protection for generator
constant
Zero sequence LCZSPTOC Fast distance protection ZMFCPDIS
overcurrent protection
Zero sequence LCZSPTOV High speed distance ZMFPDIS
overvoltage protection protection
Line differential LDLPSCH Distance measuring ZMCAPDIS
coordination zone, quadrilateral
characteristic for series
compensated lines
Additional security logic LDRGFC Distance measuring ZMCPDIS
for differential zone, quadrilateral
protection characteristic for series
compensated lines
Loss of excitation LEXPDIS Fullscheme distance ZMHPDIS
protection, mho
characteristic
Thermal overload LFPTTR Fullscheme distance ZMMAPDIS
protection, one time protection, quadrilateral
constant for earth faults
Loss of voltage check LOVPTUV Fullscheme distance ZMMPDIS
protection, quadrilateral
for earth faults
Line differential LT3CPDIF Distance protection ZMQAPDIS
protection 3 CT sets, zone, quadrilateral
with inzone characteristic
transformers, 2-3 line
ends
Line differential LT6CPDIF Distance protection ZMQPDIS
protection 6 CT sets, zone, quadrilateral
with inzone characteristic
transformers, 3-5 line
ends
Negativ sequence time NS2PTOC Distance protection ZMRAPDIS
overcurrent protection zone, quadrilateral
for machines characteristic, separate
settings
Four step directional NS4PTOC Distance protection ZMRPDIS
negative phase sequence zone, quadrilateral
overcurrent protection characteristic, separate
settings
Four step phase OC4PTOC Power swing detection ZMRPSB
overcurrent protection
Overexcitation OEXPVPH Mho Impedance ZSMGAPC
protection supervision logic
Out-of-step protection OOSPPAM Transformer tank TPPIOC
overcurrent protection
Busbar differential BCZPDIF Busbar differential BICPTRC_x, (1≤x≤5)
protection, check zone protection, bus
interconnection xx
Busbar differential BDZSGAPC Busbar differential BZNPDIF_Zx, (1≤x≤6)
protection, dynamic zone protection, zone 1
selection
Table continues on next page
Function description IEC 61850 identification Function description IEC 61850 identification
Busbar differential BFPTRC_Fx, (1≤x≤24)
protection, single phase
feeder xx
Voltage delta DELVSPVC Current delta DELISPVC
supervision, 2 phase supervision, 2 phase
DELSPVC Current harmonic CHMMHAN
monitoring, 2 phase
15.3.4.2 Setting examples for IEC/UCA 61850-9-2LE and time synchronization GUID-CEDD520A-8A13-41DF-BFF1-8A3B4C00E098 v3
The IED and the Merging Units (MU) should use the same time reference especially if analog
data is used from several sources, for example from an internal TRM and an MU, or if several
physical MUs are used. Having the same time reference is important to correlate data so that
channels from different sources refer to the correct phase angle.
When only one MU is used as an analog source, it is theoretically possible to do without time
synchronization. However, this would mean that timestamps for analog and binary data/
events become uncorrelated. If the IED has no time synchronization source configured, then
the binary data/events will be synchronized with the merging unit. However, the global/
complete time might not be correct. Disturbance recordings then appear incorrect since
analog data is timestamped by MU, and binary events use the internal IED time. It is thus
recommended to use time synchronization also when analog data emanate from only one MU.
An external time source can be used to synchronize both the IED and the MU. It is also possible
to use the MU as a clock master to synchronize the IED from the MU. When using an external
clock, it is possible to set the IED to be synchronized via PPS,IRIG-B or PTP. It is also possible to
use an internal GPS receiver in the IED (if the external clock is using GPS).
IED
9-2 PTP
SAM600 TS
SAM600 VT SAM600 CT
IEC17000040-1-en.vsdx
IEC17000040 V1 EN-US
• HwSyncSrc: is not used as the SW-time and HW-time are connected with each other due to
PTP
• SyncLostMode : set to Block to block protection functions if time synchronization is lost
or set to BlockOnLostUTC if the protection functions are to be blocked when global
common synchronization is lost
• SyncAccLevel: can be set to 1μs since this corresponds to a maximum phase angle error of
0.018 degrees at 50Hz
• Operation: On
• PTP: On
• SYNCH signal on the MUx function block indicates that protection functions are blocked
due to loss of internal time synchronization to the IED
• MUSYNCH signal on the MUx function block monitors the synchronization flag smpSynch
in the datastream and IED hardware time synchronization.
This example is not valid when GPS time is used for differential protection or
when PTP is enabled.
IED
PPS
Synchronization
IEC/UCA 61850-9-2LE
Analog data
MU
IEC10000061=2=en=Original.vsd
IEC10000061 V2 EN-US
• fineSyncSource can be set to something different to correlate events and data to other
IEDs in the station.
• SYNCH signal on the MUx function block indicates that protection functions are blocked
due to loss of internal time synchronization to the IED.
• MUSYNCH signal on the MUx function block monitors the synchronization flag smpSynch
in the datastream and IED hardware time synchronization.
SMPLLOST indicates that merging unit data are generated by internal substitution or one/
more channel's Quality is not good or merging unit is in Testmode/detailed quality=Test, IED
is not in test mode.
This example is not valid when GPS time is used for differential protection or
when PTP is enabled.
PPS / IRIG-B
IED
IEC/UCA 61850-9-2LE
data
STATION
CLOCK
PPS
MU
IEC10000074=2=en=Original.vsd
IEC10000074 V2 EN-US
• SYNCH signal on the MUx function block indicates that protection functions are blocked
due to loss of internal time synchronization to the IED (that is loss of the hardware
synchSrc).
• MUSYNCH signal on the MUx function block monitors the synchronization flag smpSynch
in the datastream and IED hardware time synchronization.
No time synchronization
This example is not valid when GPS time is used for differential protection or
when PTP is enabled.
IED
IEC/UCA 61850-9-2LE
Data
MU
IEC10000075=2=en=Original.vsd
IEC10000075 V2 EN-US
• SYNCH signal on the MUx function block indicates that protection functions are blocked
due to loss of internal time synchronization to the IED. Since SyncLostMode is set to No
block, this signal is not set.
• MUSYNCH signal on the MUx function block is set if the datastream indicates time
synchronization loss. However, protection functions are not blocked.
To get higher availability in protection functions, it is possible to avoid blocking during time
synchronization loss if there is a single source of analog data. This means that if there is only
one physical MU and no TRM, parameter SyncLostMode is set to No block but parameter
HwSyncSrc is still set to PPS. This maintains analog and binary data correlation in disturbance
recordings without blocking protection functions if PPS is lost.
The quality expander component is used to display the detailed quality of an IEC/UCA
61850-9-2LE analog channel. The component expands the channel quality output of a Merging
Unit analog channel received in the IED as per the IEC 61850-7-3 standard. This component can
be used during the ACT monitoring to get the particular channel quality of the Merging Unit.
IEC16000073-1-en.vsdx
IEC16000073 V1 EN-US
The quality expander function is intended for monitoring purposes, not for
being used in a logic controlling the behaviour of the protection or control
functions in the IED. The function outputs are updated once every second and,
therefore, do not reflect the quality bits in real time.
M14804-3 v6
Gateway
Star coupler
RER 111
IEC05000663-1-en.vsd
IEC05000663 V2 EN-US
Figure 91: Example of LON communication structure for a station automation system
An optical network can be used within the station automation system. This enables
communication with the IEDs through the LON bus from the operator’s workplace, from the
control center and also from other IEDs via bay-to-bay horizontal communication. For LON
communication an SLM card should be ordered for the IEDs.
The fiber optic LON bus is implemented using either glass core or plastic core fiber optic
cables.
The HV Control 670 software module is included in the LIB520 high-voltage process package,
which is a part of the Application Software Library in MicroSCADA applications.
The HV Control 670 software module is used for control functions in the IEDs. The module
contains a process picture, dialogues and a tool to generate a process database for the
control application in MicroSCADA.
When using MicroSCADA Monitor Pro instead of the Classic Monitor, SA LIB is used together
with 670 series Object Type files.
The HV Control 670 software module and 670 series Object Type files are used
with both 650 and 670 series IEDs.
Use the LON Network Tool (LNT) to set the LON communication. This is a software tool
applied as one node on the LON bus. To communicate via LON, the IEDs need to know
The node address is transferred to LNT via the local HMI by setting the parameter
ServicePinMsg = Yes. The node address is sent to LNT via the LON bus, or LNT can scan the
network for new nodes.
The communication speed of the LON bus is set to the default of 1.25 Mbit/s. This can be
changed by LNT.
15.4.2.1 Identification
GUID-1A6E066C-6399-4D37-8CA5-3074537E48B2 v3
The IED provides two function blocks enabling several IEDs to send and receive signals via the
interbay bus. The sending function block, MULTICMDSND, takes 16 binary inputs. LON enables
these to be transmitted to the equivalent receiving function block, MULTICMDRCV, which has
16 binary outputs.
Settings M14789-4 v3
The parameters for the multiple command function are set via PCM600.
The Mode setting sets the outputs to either a Steady or Pulsed mode.
SEMOD115767-5 v7
SPA communication protocol is an alternative to IEC 60870-5-103, and they use the same rear
communication port.
When communicating with a PC connected to the utility substation LAN via WAN and the utility
office LAN (see Figure 92), and when using the rear optical Ethernet port, the only hardware
required for a station monitoring system is:
Utility LAN
Remote
monitoring
WAN
Substation LAN
IEC05000715-4-en.vsd
IEC05000715 V4 EN-US
Figure 92: SPA communication structure for a remote monitoring system via a
substation LAN, WAN and utility LAN
SPA communication is mainly used for the Station Monitoring System. It can include different
IEDs with remote communication possibilities. Connection to a PC can be made directly (if the
PC is located in the substation), via a telephone modem through a telephone network with ITU
(former CCITT) characteristics or via a LAN/WAN connection.
Functionality SEMOD115767-25 v3
The SPA protocol V2.5 is an ASCII-based protocol for serial communication. The
communication is based on a master-slave principle, where the IED is a slave and the PC is the
master. Only one master can be applied on each fiber optic loop. A program is required in the
master computer for interpretation of the SPA-bus codes and for translation of the data that
should be sent to the IED.
For the specification of the SPA protocol V2.5, refer to SPA-bus Communication Protocol V2.5.
SPA, IEC 60870-5-103 and DNP3 use the same rear communication port. This port can be set
for SPA use on the local HMI under Main menu /Configuration /Communication /Station
communication/Port configuration/SLM optical serial port/PROTOCOL:1. When the
communication protocol is selected, the IED is automatically restarted, and the port then
operates as a SPA port.
The SPA communication setting parameters are set on the local HMI under Main menu/
Configuration/Communication/Station communication/SPA/SPA:1.
The most important SPA communication setting parameters are SlaveAddress and BaudRate.
They are essential for all communication contact to the IED. SlaveAddress and BaudRate can
be set only on the local HMI for rear and front channel communication.
SlaveAddress can be set to any value between 1–899 as long as the slave number is unique
within the used SPA loop. BaudRate (communication speed) can be set between 300–38400
baud. BaudRate should be the same for the whole station although different communication
speeds in a loop are possible. If different communication speeds are used in the same fiber
optical loop or RS485 network, take this into account when making the communication setup
in the communication master (the PC).
With local fiber optic communication, communication speed is usually set to 19200 or 38400
baud. With telephone communication, the speed setting depends on the quality of the
connection and the type of modem used. Refer to technical data to determine the rated
communication speed for the selected communication interfaces.
The IED does not adapt its speed to the actual communication conditions
because the communication speed is set on the local HMI.
M17109-3 v7
TCP/IP
Control Center
Station HSI
Gateway
Star coupler
IEC05000660-4-en.vsd
IEC05000660 V4 EN-US
When communicating locally in the station using a Personal Computer (PC) or a Remote
Terminal Unit (RTU) connected to the Communication and processing module, the only
hardware needed is optical fibers and an opto/electrical converter for the PC/RTU, or a RS-485
connection depending on the used IED communication interface.
General M17109-43 v2
The protocol implementation consists of the following functions:
• Event handling
• Report of analog service values (measurands)
• Fault location
• Command handling
• Autorecloser ON/OFF
• Teleprotection ON/OFF
• Protection ON/OFF
• LED reset
• Characteristics 1 - 4 (Setting groups)
• File transfer (disturbance files)
• Time synchronization
Hardware M17109-59 v2
When communicating locally with a Personal Computer (PC) or a Remote Terminal Unit (RTU)
in the station, using the SPA/IEC port, the only hardware needed is:· Optical fibers, glass/
plastic· Opto/electrical converter for the PC/RTU· PC/RTU
Commands M17109-62 v4
The commands defined in the IEC 60870-5-103 protocol are represented in dedicated function
blocks. These blocks have output signals for all available commands according to the protocol.
For more information, refer to the Communication protocol manual, IEC 60870-5-103.
Function block with defined IED functions in control direction, I103IEDCMD. This block use
PARAMETR as FUNCTION TYPE, and INFORMATION NUMBER parameter is defined for each
output signal.
Function block with pre-defined functions in control direction, I103CMD. This block includes
the FUNCTION TYPE parameter, and the INFORMATION NUMBER parameter is defined for each
output signal.
Function block with user defined functions in control direction, I103UserCMD. These function
blocks include the FUNCTION TYPE parameter for each block in the private range, and the
INFORMATION NUMBER parameter for each output signal.
Status M17109-74 v6
The events created in the IED available for the IEC 60870-5-103 protocol are based on the:
Function block with defined IED functions in monitor direction, I103IED. This block use
PARAMETER as FUNCTION TYPE, and INFORMATION NUMBER parameter is defined for each
input signal.
Function blocks with user defined input signals in monitor direction, I103UserDef. These
function blocks include the FUNCTION TYPE parameter for each block in the private range, and
the INFORMATION NUMBER parameter for each input signal.
Function block with defined functions for supervision indications in monitor direction,
I103Superv. This block includes the FUNCTION TYPE parameter, and the INFORMATION
NUMBER parameter is defined for each output signal.
Function block with defined functions for earth fault indications in monitor direction, I103EF.
This block includes the FUNCTION TYPE parameter, and the INFORMATION NUMBER
parameter is defined for each output signal.
Function block with defined functions for fault indications in monitor direction, I103FLTPROT.
This block includes the FUNCTION TYPE parameter, and the INFORMATION NUMBER
parameter is defined for each input signal.
This block is suitable for distance protection, line differential, transformer differential, over-
current and earth-fault protection functions.
Function block with defined functions for autorecloser indications in monitor direction,
I103AR. This block includes the FUNCTION TYPE parameter, and the INFORMATION NUMBER
parameter is defined for each output signal.
Measurands M17109-99 v2
The measurands can be included as type 3.1, 3.2, 3.3, 3.4 and type 9 according to the standard.
Function block that reports all valid measuring types depending on connected signals,
I103Meas.
Function blocks with user defined input measurands in monitor direction, I103MeasUsr. These
function blocks include the FUNCTION TYPE parameter for each block in the private range, and
the INFORMATION NUMBER parameter for each block.
• The transfer functionality is based on the Disturbance recorder function. The analog and
binary signals recorded will be reported to the master by polling. The eight last
disturbances that are recorded are available for transfer to the master. A file that has
been transferred and acknowledged by the master cannot be transferred again.
• The binary signals that are included in the disturbance recorder are those that are
connected to the disturbance function blocks B1RBDR to B22RBDR. These function blocks
include the function type and the information number for each signal. For more
information on the description of the Disturbance report in the Technical reference
manual. The analog channels, that are reported, are those connected to the disturbance
function blocks A1RADR to A4RADR. The eight first ones belong to the public range and
the remaining ones to the private range.
15.6.2.1 Settings for RS485 and optical serial communication M17109-118 v12
General settings
SPA, DNP and IEC 60870-5-103 can be configured to operate on the SLM optical serial port
while DNP and IEC 60870-5-103 additionally can utilize the RS485 port. A single protocol can be
active on a given physical port at any time.
Two different areas in the HMI are used to configure the IEC 60870-5-103 protocol.
1. The port specific IEC 60870-5-103 protocol parameters are configured under:
Main menu/Configuration/Communication/Station Communication/IEC60870-5-103/
• <config-selector>
• SlaveAddress
• BaudRate
• RevPolarity (optical channel only)
• CycMeasRepTime
• MasterTimeDomain
• TimeSyncMode
• EvalTimeAccuracy
• EventRepMode
• CmdMode
• RepIntermediatePos
<config-selector> is:
• “OPTICAL103:1” for the optical serial channel on the SLM
• “RS485103:1” for the RS485 port
2. The protocol to activate on a physical port is selected under:
Main menu/Configuration/Communication/Station Communication/Port
configuration/
• RS485 port
GUID-CD4EB23C-65E7-4ED5-AFB1-A9D5E9EE7CA8 V3 EN
GUID-CD4EB23C-65E7-4ED5-AFB1-A9D5E9EE7CA8 V3 EN-US
• SlaveAddress and BaudRate: Settings for slave number and communication speed (baud
rate).
The slave number can be set to any value between 1 and 254. The communication speed,
can be set either to 9600 bits/s or 19200 bits/s.
• RevPolarity: Setting for inverting the light (or not). Standard IEC 60870-5-103 setting is
On.
• CycMeasRepTime: See I103MEAS function block for more information.
• EventRepMode: Defines the mode for how events are reported. The event buffer size is
1000 events.
I103USEDEF GUID-A41170D6-2846-4E5E-8B7F-85B53D4EF6B6 v1
For each input of the I103USEDEF function there is a setting for the information number of the
connected signal. The information number can be set to any value between 0 and 255. To get
proper operation of the sequence of events the event masks in the event function is to be set
to ON_CHANGE. For single-command signals, the event mask is to be set to ON_SET.
In addition there is a setting on each event block for function type. Refer to description of the
Main Function type set on the local HMI.
Commands M17109-138 v2
As for the commands defined in the protocol there is a dedicated function block with eight
output signals. Use PCM600 to configure these signals. To realize the BlockOfInformation
command, which is operated from the local HMI, the output BLKINFO on the IEC command
function block ICOM has to be connected to an input on an event function block. This input
must have the information number 20 (monitor direction blocked) according to the standard.
Recorded analog channels are sent with ASDU26 and ASDU31. One information element in
these ASDUs is called ACC, and it indicates the actual channel to be processed. The channels
on disturbance recorder are sent with an ACC as shown in Table 31.
Refer to the tables in the Technical reference manual /Station communication, specifying the
information types supported by the communication protocol IEC 60870-5-103.
To support the information, corresponding functions must be included in the protection IED.
Glass or plastic fiber should be used. BFOC/2.5 is the recommended interface to use
(BFOC/2.5 is the same as ST connectors). ST connectors are used with the optical power as
specified in standard.
For more information on the application and setting guidelines for the DNP3 communication
protocol refer to the DNP3 Communication protocol manual.
Section 16 Security
16.1 Authority status ATHSTAT SEMOD158575-1 v2
Authority status (ATHSTAT) function is an indication function block, which informs about two
events related to the IED and the user authorization:
• the fact that at least one user has tried to log on wrongly into the IED and it was blocked
(the output USRBLKED)
• the fact that at least one user is logged on (the output LOGGEDON)
The two outputs of ATHSTAT function can be used in the configuration for different indication
and alarming reasons, or can be sent to the station control for the same purpose.
The protection and control IEDs have many functions included. The included self-supervision
with internal event list function block provides good supervision of the IED. The fault signals
make it easier to analyze and locate a fault.
Both hardware and software supervision is included and it is also possible to indicate possible
faults through a hardware contact on the power supply module and/or through the
communication.
Internal events are generated by the built-in supervisory functions. The supervisory functions
supervise the status of the various modules in the IED and, in case of failure, a corresponding
event is generated. Similarly, when the failure is corrected, a corresponding event is generated.
Apart from the built-in supervision of the various modules, events are also generated when the
status changes for the:
The internal events are time tagged with a resolution of 1 ms and stored in a list. The list can
store up to 40 events. The list is based on the FIFO principle, that is, when it is full, the oldest
event is overwritten. The list contents cannot be modified, but the whole list can be cleared
using the Reset menu in the LHMI.
The list of internal events provides valuable information, which can be used during
commissioning and fault tracing.
The information can, in addition to be viewed on the built in HMI, also be retrieved with the aid
of a PC with PCM600 installed and by using the Event Monitoring Tool. The PC can either be
connected to the front port, or to the port at the back of the IED.
Change lock function CHNGLCK is used to block further changes to the IED configuration once
the commissioning is complete. The purpose is to make it impossible to perform inadvertent
IED configuration and setting changes.
However, when activated, CHNGLCK will still allow the following actions that does not involve
reconfiguring of the IED:
• Monitoring
• Reading events
• Resetting events
• Reading disturbance data
• Clear disturbances
• Reset LEDs
• Reset counters and other runtime component states
• Control operations
• Set system time
• Enter and exit from test mode
• Change of active setting group
The binary input controlling the function is defined in ACT or SMT. The CHNGLCK function is
configured using ACT.
LOCK Binary input signal that will activate/deactivate the function, defined in ACT or SMT.
GUID-8C333BC0-AA7A-4ED1-A772-18C22E8EEE62 v6
When CHNGLCK has a logical one on its input, then all attempts to modify the
IED configuration and setting will be denied and the message "Error: Changes
blocked" will be displayed on the local HMI; in PCM600 the message will be
"Operation denied by active ChangeLock". The CHNGLCK function should be
configured so that it is controlled by a signal from a binary input card. This
guarantees that by setting that signal to a logical zero, CHNGLCK is
deactivated. If any logic is included in the signal path to the CHNGLCK input,
that logic must be designed so that it cannot permanently issue a logical one
to the CHNGLCK input. If such a situation would occur in spite of these
precautions, then please contact the local ABB representative for remedial
action.
The denial of service functionality is designed to limit the CPU load that can be produced by
Ethernet network traffic on the IED. The communication facilities must not be allowed to
compromise the primary functionality of the device. All inbound network traffic will be quota
controlled so that too heavy network loads can be controlled. Heavy network load might for
instance be the result of malfunctioning equipment connected to the network.
The functions Access point diagnostics function block measure the IED load from
communication and, if necessary, limit it for not jeopardizing the IEDs control and protection
functionality due to high CPU load. The function has the following denial of service related
outputs:
• LINKSTS indicates the Ethernet link status for the rear ports (single communication)
• CHALISTS and CHBLISTS indicates the Ethernet link status for the rear ports channel A
and B (redundant communication)
• LinkStatus indicates the Ethernet link status for the front port
The function does not have any parameters available in the local HMI or PCM600.
IED identifiers (TERMINALID) function allows the user to identify the individual IED in the
system, not only in the substation, but in a whole region or a country.
Use only characters A-Z, a-z and 0-9 in station, object and unit names.
Product information contains unchangeable data that uniquely identifies the IED.
Product information data is visible on the local HMI under Main menu/Diagnostics/IED
status/Product identifiers and under Main menu/Diagnostics/IED Status/Identifiers:
Product information data is visible on the local HMI under Main menu/Diagnostics/IED
status/Product identifiers and under Main menu/Diagnostics/IED Status/Identifiers.
• ProductVer
• ProductDef
• FirmwareVer
• SerialNo
• OrderingNo
• ProductionDate
• IEDProdType
The factory defined settings are very useful for identifying a specific version and very helpful in
the case of maintenance, repair, interchanging IEDs between different Substation Automation
Systems and upgrading. The factory made settings can not be changed by the customer. They
can only be viewed. The settings are found in the local HMI under Main menu/Diagnostics/IED
status/Product identifiers
• IEDProdType
• Describes the type of the IED. Example: REL650
• ProductDef
1 is the Major version of the manufactured product this means, new platform of the product
2 is the Minor version of the manufactured product this means, new functions or new hardware
added to the product
3 is the Major revision of the manufactured product this means, functions or hardware is either
changed or enhanced in the product
• IEDMainFunType
• Main function type code according to IEC 60870-5-103. Example: 128 (meaning line
protection).
• SerialNo
• OrderingNo
• ProductionDate
17.3.1 Identification
SEMOD113212-2 v3
The current and voltage measurements functions (CVMMXN, CMMXU, VMMXU and VNMMXU),
current and voltage sequence measurement functions (CMSQI and VMSQI) and IEC 61850
generic communication I/O functions (MVGAPC) are provided with measurement supervision
functionality. All measured values can be supervised with four settable limits, that is low-low
limit, low limit, high limit and high-high limit. The measure value expander block ( RANGE_XP)
has been introduced to be able to translate the integer output signal from the measuring
functions to 5 binary signals, that is below low-low limit, below low limit, normal, above high-
high limit or above high limit. The output signals can be used as conditions in the configurable
logic.
There are no settable parameters for the measured value expander block function.
Six sets of settings are available to optimize IED operation for different power system
conditions. By creating and switching between fine tuned setting sets, either from the local
HMI or configurable binary inputs, results in a highly adaptable IED that can cope with a variety
of power system scenarios.
Different conditions in networks with different voltage levels require highly adaptable
protection and control units to best provide for dependability, security and selectivity
requirements. Protection units operate with a higher degree of availability, especially, if the
setting values of their parameters are continuously optimized according to the conditions in
the power system.
Operational departments can plan for different operating conditions in the primary
equipment. The protection engineer can prepare the necessary optimized and pre-tested
settings in advance for different protection functions. Six different groups of setting
parameters are available in the IED. Any of them can be activated through the different
programmable binary inputs by means of external or internal control signals.
A function block, SETGRPS, defines how many setting groups are used. Setting is done with
parameter MAXSETGR and shall be set to the required value for each IED. Only the number of
setting groups set will be available in the Parameter Setting tool for activation with the
ActiveGroup function block.
The setting ActiveSetGrp, is used to select which parameter group to be active. The active
group can also be selected with configured input to the function block SETGRPS.
The length of the pulse, sent out by the output signal SETCHGD when an active group has
changed, is set with the parameter t.
The parameter MAXSETGR defines the maximum number of setting groups in use to switch
between. Only the selected number of setting groups will be available in the Parameter Setting
tool (PST) for activation with the ActiveGroup function block.
17.5.1 Identification
GUID-B8B3535D-227B-4151-9E98-BEB85F4D54DE v1
The rated system frequency and phase rotation direction are set under Main menu/
Configuration/ Power system/ Primary Values in the local HMI and PCM600 parameter
setting tree.
Set the system rated frequency. Refer to section "Signal matrix for analog inputs SMAI" for
description on frequency tracking.
The analog summation block 3PHSUM function block is used in order to get the sum of two
sets of 3 phase analog signals (of the same type) for those IED functions that might need it.
The summation block receives the three-phase signals from SMAI blocks. The summation block
has several settings.
DFTReference: The reference DFT block (InternalDFT Ref,DFTRefGrp1 or External DFT ref) .
DFTRefGrp1: This setting means use own internal adaptive DFT reference ( this setting makes
the SUM3PH self DFT adaptive, that is, it will use the measured frequency for the summation
signal to adapt DFT).
ExternalDFTRef: This setting means that the DFT samples-per-cycle (adaptive DFT) will be
controlled by SMAI1 SPFCOUT.
FreqMeasMinVal: The minimum value of the voltage for which the frequency is calculated,
expressed as percent of UBasebase voltage setting (for each instance x).
GlobalBaseSel: Selects the global base value group used by the function to define (IBase),
(UBase) and (SBase).
17.7.1 Identification
GUID-0D5405BE-E669-44C8-A208-3A4C86D39115 v3
Global base values function (GBASVAL) is used to provide global values, common for all
applicable functions within the IED. One set of global values consists of values for current,
voltage and apparent power and it is possible to have twelve different sets.
This is an advantage since all applicable functions in the IED use a single source of base values.
This facilitates consistency throughout the IED and also facilitates a single point for updating
values when necessary.
Each applicable function in the IED has a parameter, GlobalBaseSel, defining one out of the
twelve sets of GBASVAL functions.
UBase: Phase-to-phase voltage value to be used as a base value for applicable functions
throughout the IED.
IBase: Phase current value to be used as a base value for applicable functions throughout the
IED.
SBase: Standard apparent power value to be used as a base value for applicable functions
throughout the IED, typically SBase=√3·UBase·IBase.
The Signal matrix for binary inputs function SMBI is used within the Application Configuration
tool in direct relation with the Signal Matrix tool. SMBI represents the way binary inputs are
brought in for one IED configuration.
There are no setting parameters for the Signal matrix for binary inputs SMBI available to the
user in Parameter Setting tool. However, the user shall give a name to SMBI instance and the
SMBI inputs, directly in the Application Configuration tool. These names will define SMBI
function in the Signal Matrix tool. The user defined name for the input or output signal will also
appear on the respective output or input signal.
The Signal matrix for binary outputs function SMBO is used within the Application
Configuration tool in direct relation with the Signal Matrix tool. SMBO represents the way
binary outputs are sent from one IED configuration.
There are no setting parameters for the Signal matrix for binary outputs SMBO available to the
user in Parameter Setting tool. However, the user must give a name to SMBO instance and
SMBO outputs, directly in the Application Configuration tool. These names will define SMBO
function in the Signal Matrix tool.
Signal matrix for analog inputs (SMAI), also known as the preprocessor function block,
analyses the connected four analog signals (three phases and neutral) and calculates all
relevant information from them like the phasor magnitude, phase angle, frequency, true RMS
value, harmonics, sequence components and so on. This information is then used by the
respective functions connected to this SMAI block in ACT (for example protection,
measurement or monitoring functions).
The SMAI function includes a functionality based on the level of positive sequence voltage,
MinValFreqMeas, to validate if the frequency measurement is valid or not. If the positive
sequence voltage is lower than MinValFreqMeas, the function freezes the frequency output
value for 500 ms and after that the frequency output is set to the nominal value. A signal is
available for the SMAI function to prevent operation due to non-valid frequency values.
MinValFreqMeas is set as % of UBase/√3
If SMAI setting ConnectionType is Ph-Ph, at least two of the inputs GRPxL1, GRPxL2 and
GRPxL3, where 1≤x≤12, must be connected in order to calculate the positive sequence voltage.
Note that phase to phase inputs shall always be connected as follows: L1-L2 to GRPxL1, L2-L3
to GRPxL2, L3-L1 to GRPxL3. If SMAI setting ConnectionType is Ph-N, all three inputs GRPxL1,
GRPxL2 and GRPxL3 must be connected in order to calculate the positive sequence voltage.
If only one phase-phase voltage is available and SMAI setting ConnectionType is Ph-Ph, the
user is advised to connect two (not three) of the inputs GRPxL1, GRPxL2 and GRPxL3 to the
same voltage input as shown in figure 96 to make SMAI calculate a positive sequence voltage.
SMAI1
BLOCK SPFCOUT SAPTOF
DFTSPFC G1AI3P U3P* TRIP SAPTOF(1)_TRIP
UL1L2 BLOCK START
REVROT G1AI1
PHASEL1 G1AI2 BLKTRIP BLKDMAGN
^GRP1L1 G1AI4 FREQ
TRM_40.CH7(U) PHASEL2
G1N
^GRP1L2
PHASEL3
^GRP1L3
NEUTRAL
^GRP1N
EC10000060-3-en.vsdx
IEC10000060 V3 EN-US
The above described scenario does not work if SMAI setting ConnectionType is
Ph-N. If only one phase-earth voltage is available, the same type of connection
can be used but the SMAI ConnectionType setting must still be Ph-Ph and this
has to be accounted for when setting MinValFreqMeas. If SMAI setting
ConnectionType is Ph-N and the same voltage is connected to all three SMAI
inputs, the positive sequence voltage will be zero and the frequency functions
will not work properly.
The outputs from the above configured SMAI block shall only be used for
Overfrequency protection (SAPTOF), Underfrequency protection (SAPTUF) and
Rate-of-change frequency protection (SAPFRC) due to that all other
information except frequency and positive sequence voltage might be wrongly
calculated.
The parameters for the signal matrix for analog inputs (SMAI) functions are set via the local
HMI or PCM600.
Every SMAI function block can receive four analog signals (three phases and one neutral value),
either voltage or current. SMAI outputs give information about every aspect of the 3ph analog
signals acquired (phase angle, RMS value, frequency and frequency derivates, and so on – 244
values in total). Besides the block “group name”, the analog inputs type (voltage or current)
and the analog input names that can be set directly in ACT.
Application functions should be connected to a SMAI block with same task cycle as the
application function, except for e.g. measurement functions that run in slow cycle tasks.
These DFT reference block settings decide DFT reference for DFT calculations. The setting
InternalDFTRef will use fixed DFT reference based on set system frequency. DFTRefGrp(n) will
use DFT reference from the selected group block, when own group is selected, an adaptive
DFT reference will be used based on calculated signal frequency from own group. The setting
ExternalDFTRef will use reference based on what is connected to input DFTSPFC.
The setting ConnectionType: Connection type for that specific instance (n) of the SMAI (if it is
Ph-N or Ph-Ph). Depending on connection type setting the not connected Ph-N or Ph-Ph
outputs will be calculated as long as they are possible to calculate. E.g. at Ph-Ph connection L1,
L2 and L3 will be calculated for use in symmetrical situations. If N component should be used
respectively the phase component during faults IN/UN must be connected to input 4.
Negation: If the user wants to negate the 3ph signal, it is possible to choose to negate only the
phase signals Negate3Ph, only the neutral signal NegateN or both Negate3Ph+N. negation
means rotation with 180° of the vectors.
GlobalBaseSel: Selects the global base value group used by the function to define (IBase),
(UBase) and (SBase).
MinValFreqMeas: The minimum value of the voltage for which the frequency is calculated,
expressed as percent of UBase (for each instance n).
Even if the user sets the AnalogInputType of a SMAI block to “Current”, the
MinValFreqMeas is still visible. However, using the current channel values as
base for frequency measurement is not recommendable for a number of
reasons, not last among them being the low level of currents that one can have
in normal operating conditions.
Preprocessing block shall only be used to feed functions within the same
execution cycles (e.g. use preprocessing block with cycle 1 to feed transformer
differential protection). The only exceptions are measurement functions
(CVMMXN, CMMXU,VMMXU, etc.) which shall be fed by preprocessing blocks
with cycle 8.
When two or more preprocessing blocks are used to feed one protection
function (e.g. over-power function GOPPDOP), it is of outmost importance that
parameter setting DFTReference has the same set value for all of the
preprocessing blocks involved
IEC07000197.vsd
IEC07000197 V2 EN-US
Figure 97: Twelve SMAI instances are grouped within one task time. SMAI blocks are
available in three different task times in the IED. Two pointed instances are
used in the following examples.
The examples shows a situation with adaptive frequency tracking with one reference selected
for all instances. In practice each instance can be adapted to the needs of the actual
application. The adaptive frequency tracking is needed in IEDs that belong to the protection
system of synchronous machines and that are active during run-up and shout-down of the
machine. In other application the usual setting of the parameter DFTReference of SMAI is
InternalDFTRef.
Example 1
SMAI1:13
BLOCK SPFCOUT
DFTSPFC AI3P
^GRP1L1 AI1
^GRP1L2 AI2
^GRP1L3 AI3
SMAI1:1 ^GRP1N AI4
BLOCK SPFCOUT AIN
DFTSPFC AI3P
^GRP1L1 AI1
^GRP1L2 AI2
^GRP1L3 AI3
^GRP1N AI4
AIN
SMAI1:25
BLOCK SPFCOUT
DFTSPFC AI3P
^GRP1L1 AI1
^GRP1L2 AI2
^GRP1L3 AI3
^GRP1N AI4
AIN
IEC07000198-2-en.vsd
IEC07000198 V3 EN-US
Figure 98: Configuration for using an instance in task time group 1 as DFT reference
Assume instance SMAI7:7 in task time group 1 has been selected in the configuration to control
the frequency tracking . Observe that the selected reference instance (i.e. frequency tracking
master) must be a voltage type. Observe that positive sequence voltage is used for the
frequency tracking feature.
For task time group 1 this gives the following settings (see Figure 97 for numbering):
Example 2
SMAI1:1
BLOCK SPFCOUT
DFTSPFC AI3P
^GRP1L1 AI1
^GRP1L2 AI2
^GRP1L3 AI3
SMAI1:13 ^GRP1N AI4
BLOCK SPFCOUT AIN
DFTSPFC AI3P
^GRP1L1 AI1
^GRP1L2 AI2
^GRP1L3 AI3
^GRP1N AI4
AIN
SMAI1:25
BLOCK SPFCOUT
DFTSPFC AI3P
^GRP1L1 AI1
^GRP1L2 AI2
^GRP1L3 AI3
^GRP1N AI4
AIN
IEC07000199-2-en.vsd
IEC07000199 V3 EN-US
Figure 99: Configuration for using an instance in task time group 2 as DFT reference.
Assume instance SMAI4:16 in task time group 2 has been selected in the configuration to
control the frequency tracking for all instances. Observe that the selected reference instance
(i.e. frequency tracking master) must be a voltage type. Observe that positive sequence
voltage is used for the frequency tracking feature.
For task time group 1 this gives the following settings (see Figure 97 for numbering):
The protection and control IEDs may have a complex configuration with many included
functions. To make the testing procedure easier, the IEDs include the feature that allows
individual blocking of a single-, several-, or all functions.
This means that it is possible to see when a function is activated or trips. It also enables the
user to follow the operation of several related functions to check correct functionality and to
check parts of the configuration, and to check parts.
The function block TESTMODE has implemented the extended testing mode capabilities for
IEC 61850 Ed2 systems. Operator commands sent to the function block TESTMODE determine
the behavior of the functions. The command can be given remotely from an IEC 61850 client or
from the LHMI under the Main menu/Test/Function test modes/Communication/Station
Communication/IEC61850 LD0 LLN0/LD0LLN0:1. The possible values of the function block
TESTMODE are described in Communication protocol manual, IEC 61850 Edition 1 and Edition
2.
There is no setting in PCM600 via PST for the TESTMODE function block.
To be able to set the function block TESTMODE remotely, the setting via path
on LHMI and in PST: Main menu/Configuration/Communication/ Station
Communication/IEC61850-8-1/IEC61850-8-1:1RemoteModControl may not be
set to Off. The possible values of the parameter RemoteModControl are Off,
Maintenance or All levels. The Off value denies all access to function block
TESTMODE from remote, Maintenance requires that the category of the
originator (orCat) is Maintenance and All levels allow any orCat.
The DataObject Mod of the Root LD.LNN0 can be set on the LHMI under Main menu/Test/
Function test modes/Communication/Station communication/IEC61850 LD0 LLN0/
LD0LLN0:1 to On, Off, TestBlocked,Test or Blocked.
When the setting of the DataObject Mod is changed at this level, all Logical Nodes inside the
logical device update their own behavior according to IEC61850-7-4. The supported values of
the function block TESTMODE are described in Communication protocol manual, IEC 61850
Edition 2. When the function block TESTMODE is in test mode the Start LED on the LHMI is
turned on with steady light.
The parameter Mod of any specific function block can be configured under Main menu/Test/
Function test modes/Communication/Station Communication
The parameter Mod can be set on the LHMI to the same values as for the DataObject Mod of
the Root LD.LNN0 to On, Off, TestBlocked,Test or Blocked. For Example, Main menu/ Test/
Function test modes/ Differential protection/GeneratorDiff(87G,3Id/I>)/ GENPDIF(87G,3Id/
I>):1.
It is possible that the behavior of the function block TESTMODE is also influenced by other
sources as well, independent of the mode communicated via the IEC61850-8-1 station bus. For
example the insertion of the test handle into the test switch with its auxiliary contact is
connected to a BI on the IED and further inside the configuration to the input IED_TEST on the
function block TESTMODE. Another example is when loss of Service Values appears, or as
explained above the setting via the LHMI.
When setting via PST or LHMI the parameterOperation of any function in an IED is set to Off,
the function is not executed and the behavior (beh) is set toOff and it is not possible to
override it. When a behavior of a function is Off the function will not execute. The related Mod
keeps its current state.
When IEC 61850 Mod of a function is set to Off or Blocked, the Start LED on the
LHMI will be set to flashing to indicate the abnormal operation of the IED.
The IEC 61850-7-4 gives a detailed overview over all aspects of the test mode and other states
of mode and behavior. The status of a function block behavior Beh is shown on the LHMI under
• When the Beh of a function block is set to Test, the function block is not blocked and all
control commands with a test bit are accepted.
• When the Beh of a function block is set to Test/blocked, all control commands with a test
bit are accepted. Outputs to the process via a non-IEC 61850 link data are blocked by the
function block. Only process-related outputs on function blocks related to primary
equipment are blocked. If there is an XCBR function block used, the outputs EXC_Open
and EXC_Close are blocked.
• When the Beh of a function block is set to Blocked, all control commands with a test bit
are accepted. Outputs to the process via a non-IEC 61850 link data are blocked by the
function block. In addition, the function block can be blocked when their Beh is blocked.
This can be done if the function block has a block input.
The block status of a component is shown on the LHMI as the Blk output under the same path
as for Beh:Main menu/Test/Function status/Function group/Function block descriptive
name/LN name/Outputs. If the Blk output is not shown, the component cannot be blocked.
Remember always that there are two possible ways to place the IED in the TestMode= On”
state. If, the IED is set to normal operation (TestMode = Off), but the functions are still shown
being in the test mode, the input signal IED_TEST on the TESTMODE function block is
activated in the configuration.
Forcing of binary input and output signals is only possible when the IED is in IED test mode.
Use time synchronization to achieve a common time base for the IEDs in a protection and
control system. This makes it possible to compare events and disturbance data between all
IEDs in the system.
Time-tagging of internal events and disturbances are an excellent help when evaluating faults.
Without time synchronization, only the events within one IED can be compared with each
other. With time synchronization, events and disturbances within the whole network, can be
compared and evaluated.
In the IED, the internal time can be synchronized from the following sources:
Out of these, LON and SPA contains two types of synchronization messages:
• Coarse time messages are sent every minute and contain complete date and time, that is
year, month, day, hour, minute, second and millisecond.
• Fine time messages are sent every second and comprise only seconds and milliseconds.
The selection of the time source is done via the corresponding setting.
If PTP is activated, the device with the best accuracy within the synchronizing group will be
selected as the source. For more information about PTP, see the Technical manual.
All the parameters related to time are divided into two categories: System time and
Synchronization.
The time is set with years, month, day, hour, minute, second and millisecond.
The setting parameters for the real-time clock with external time synchronization are set via
local HMI or PCM600. The path for Time Synchronization parameters on local HMI is Main
menu/Configuration/Time/Synchronization. The parameters are categorized as Time
Synchronization (TIMESYNCHGEN) and IRIG-B settings (IRIG-B:1) in case that IRIG-B is used as
the external time synchronization source.
• Off
• SPA
• LON
• BIN (Binary Minute Pulse)
• SNTP
• IRIG-B
• PPS
• Off
• SPA
• LON
• DNP
• IEC 60870-5-103
The function input to be used for minute-pulse synchronization is called BININPUT. For a
description of the BININPUT settings, see the Technical Manual.
The system time can be set manually, either via the local HMI or via any of the communication
ports. The time synchronization fine tunes the clock (seconds and milliseconds).
The parameter SyncMaster defines if the IED is a master, or not a master for time
synchronization within a Substation Automation System, for IEDs connected in a
communication network (IEC 61850-8-1). The SyncMaster can have the following values:
• Off
• SNTP -Server
PTP can be set to On,Off or Slave only. When set to Slave only the IED is connected to the PTP-
group and will synchronize to the grandmaster but cannot function as the grandmaster.
A PTP-group is set up by connecting the IEDs to a network and enabling PTP. To set one IED as
the grandmaster change Priority2 to 127 instead of the default 128.
IEC16000089-1-en.vsdx
IEC16000089 V1 EN-US
The PTP VLAN tag does not need to be the same on all access points in one IED. It is possible
to mix as long as they are the same for all devices on each subnet.
Setting example
GPS
PTP
Station bus
PTP PTP
REC REL
Process bus
9-2
SAM600-TS
SAM600-CT
SAM600-VT
IEC17000069=1=en.vsdx
IEC17000069 V1 EN-US
When process bus communication (IEC/UCA 61850-9-2LE protocol) is used, it is essential that
the merging units are synchronized with the hardware time of the IED (see Technical manual,
section Design of the time system (clock synchronization) ). To achieve this, PTP, PPS or IRIG-B
can be used depending of the facilities of the merging unit.
If the merging unit supports PTP, use PTP. If PTP is used in the IED and the merging unit
cannot be synchronized from the IED, then use GPS-based clocks to provide PTP synch as well
as sync to the merging unit.
If synchronization of the IED and the merging unit is based on GPS, set the parameter
SyncLostMode to BlockOnLostUTC in order to provide a block of protection functions
whenever the global common time is lost.
If PTP is not used, use the same synchronization method for the HwSyncSrc as the merging
unit provides. For instance, if the merging unit provides PPS as synchronization, use PPS as
HwSyncSrc. If LDCM in GPS-mode is used, that is, the hardware and software clocks are
connected to each other, HwSyncSrc is not used and other means to synchronize the merging
unit to the IED is required. For instance, FineSyncSource is set to the same source that the
merging unit uses.
If the IED is used together with a merging unit and no time synchronization is
available, for example, in the laboratory test, the IED will synchronize to the SV
data stream. During the re-synchronization, the protection functions will be
blocked once a second for about 45 ms, and this will continue for up to 10
minutes. To avoid this, configure PTP (IEEE 1588) to On for the access point
where the merging unit is configured.
Section 18 Requirements
18.1 Current transformer requirements IP15171-1 v2
M11609-3 v2
The performance of a protection function will depend on the quality of the measured current
signal. Saturation of the current transformers (CTs) will cause distortion of the current signals
and can result in a failure to operate or cause unwanted operations of some functions.
Consequently CT saturation can have an influence on both the dependability and the security
of the protection. This protection IED has been designed to permit heavy CT saturation with
maintained correct operation.
M11611-4 v5
To guarantee correct operation, the current transformers (CTs) must be able to correctly
reproduce the current for a minimum time before the CT will begin to saturate. To fulfill the
requirement on a specified time to saturation the CTs must fulfill the requirements of a
minimum secondary e.m.f. that is specified below.
CTs are specified according to many different classes and standards. In principle, there are
three different types of protection CTs. These types are related to the design of the iron core
and the presence of airgaps. Airgaps affects the properties of the remanent flux.
The following three different types of protection CTs have been specified:
• The High Remanence type with closed iron core and no specified limit of the remanent flux
• The Low Remanence type with small airgaps in the iron core and the remanent flux limit is
specified to be maximum 10% of the saturation flux
• The Non Remanence type with big airgaps in the iron core and the remanent flux can be
neglected
Even though no limit of the remanent flux is specified in the IEC standard for closed core CTs,
it is a common opinion that the remanent flux is normally limited to maximum 75 - 80 % of the
saturation flux.
Since approximately year 2000 some CT manufactures have introduced new core materials
that gradually have increased the possible maximum levels of remanent flux even up to 95 %
related to the hysteresis curve. Corresponding level of actual remanent flux is 90 % of the
saturation flux (Ψsat). As the present CT standards have no limitation of the level of remanent
flux, these CTs are also classified as for example, class TPX, P and PX according to IEC. The IEC
TR 61869-100, Edition 1.0 2017-01, Instrument transformers – Guidance for application of
current transformers in power system protection, is the first official document that
highlighted this development. So far remanence factors of maximum 80% have been
considered when CT requirements have been decided for ABB IEDs. Even in the future this level
of remanent flux probably will be the maximum level that will be considered when decided the
CT requirements. If higher remanence levels should be considered, it should often lead to
unrealistic CT sizes.
Thus, now there is a need to limit the acceptable level of remanent flux. To be able to
guarantee the performance of protection IEDs, we need to introduce the following
classification of CTs.
There are many different standards and a lot of classes but fundamentally there are four
different types of CTs:
The Very High Remanence (VHR) type is a CT with closed iron core (for example. protection
classes TPX, P, PX according to IEC, class C, K according to ANSI/IEEE) and with an iron core
material (new material, typically new alloy based magnetic materials) that gives a remanent
flux higher than 80 % of the saturation flux.
The High Remanence (HR) type is a CT with closed iron core (for example, protection classes
TPX, P, PX according to IEC, class C, K according to ANSI/IEEE) but with an iron core material
(traditional material) that gives a remanent flux that is limited to maximum 80 % of the
saturation flux.
The Low Remanence (LR) type is a CT with small airgaps in the iron core (for example, TPY, PR,
PXR according to IEC) and the remanent flux limit is specified to be maximum 10% of the
saturation flux.
The Non Remanence (NR) type is a CT with big airgaps in the core (for example, TPZ according
to IEC) and the remanent flux can be neglected.
CT type VHR (using new material) should not be used for protection CT cores. This means that
it is important to specify that the remanence factor must not exceed 80 % when ordering for
example, class P, PX or TPX CTs. If CT manufacturers are using new core material and are not
able to fulfill this requirement, the CTs shall be specified with small airgaps and therefore will
be CTs of LR type (for example, class PR, TPY or PXR). Very high remanence level in a protection
core CT can cause the following problems for protection IEDs:
No information is available about how frequent the use of the new iron core material is for
protection CT cores, but it is known that some CT manufacturers are using the new material
while other manufacturers continue to use the old traditional core material for protection CT
cores. In a case where VHR type CTs have been already installed, the calculated values of Eal for
HR type CTs, for which the formulas are given in this document, must be multiplied by factor
two-and-a-half in order for VHR type CTs (i.e. with new material) to be used together with ABB
protection IEDs. However, this may result in unacceptably big CT cores, which can be difficult
to manufacture and fit in available space.
Different standards and classes specify the saturation e.m.f. in different ways but it is possible
to approximately compare values from different classes. The rated equivalent limiting
secondary e.m.f. Eal according to the IEC 61869–2 standard is used to specify the CT
requirements for the IED. The requirements are also specified according to other standards.
M11610-4 v5
The requirements are a result of investigations performed in our network simulator. The
current transformer models are representative for current transformers of high remanence
and low remanence type. The results may not always be valid for non remanence type CTs
(TPZ).
The performances of the protection functions have been checked in the range from
symmetrical to fully asymmetrical fault currents. Primary time constants of at least 120 ms
have been considered at the tests. The current requirements below are thus applicable both
for symmetrical and asymmetrical fault currents.
The remanence in the current transformer core can cause unwanted operations or minor
additional time delays for some protection functions. As unwanted operations are not
acceptable at all maximum remanence has been considered for fault cases critical for the
security, for example, faults in reverse direction and external faults. Because of the almost
negligible risk of additional time delays and the non-existent risk of failure to operate the
remanence have not been considered for the dependability cases. The requirements below are
therefore fully valid for all normal applications.
It is difficult to give general recommendations for additional margins for remanence to avoid
the minor risk of an additional time delay. They depend on the performance and economy
requirements. When current transformers of low remanence type (for example, TPY, PR) are
used, normally no additional margin is needed. For current transformers of high remanence
type (for example, P, PX, TPX) the small probability of fully asymmetrical faults, together with
high remanence in the same direction as the flux generated by the fault, has to be kept in mind
at the decision of an additional margin. Fully asymmetrical fault current will be achieved when
the fault occurs at approximately zero voltage (0°). Investigations have shown that 95% of the
faults in the network will occur when the voltage is between 40° and 90°. In addition fully
asymmetrical fault current will not exist in all phases at the same time.
M11613-4 v4
The current transformer requirements are based on the maximum fault current for faults in
different positions. Maximum fault current will occur for three-phase faults or single phase-to-
earth faults. The current for a single phase-to-earth fault will exceed the current for a three-
phase fault when the zero sequence impedance in the total fault loop is less than the positive
sequence impedance.
When calculating the current transformer requirements, maximum fault current for the
relevant fault position should be used and therefore both fault types have to be considered.
M11614-4 v5
The voltage at the current transformer secondary terminals directly affects the current
transformer saturation. This voltage is developed in a loop containing the secondary wires and
the burden of all relays in the circuit. For earth faults the loop includes the phase and neutral
wire, normally twice the resistance of the single secondary wire. For three-phase faults the
neutral current is zero and it is just necessary to consider the resistance up to the point where
the phase wires are connected to the common neutral wire. The most common practice is to
use four wires secondary cables so it normally is sufficient to consider just a single secondary
wire for the three-phase case.
The conclusion is that the loop resistance, twice the resistance of the single secondary wire,
must be used in the calculation for phase-to-earth faults and the phase resistance, the
resistance of a single secondary wire, may normally be used in the calculation for three-phase
faults.
As the burden can be considerable different for three-phase faults and phase-to-earth faults it
is important to consider both cases. Even in a case where the phase-to-earth fault current is
smaller than the three-phase fault current the phase-to-earth fault can be dimensioning for the
CT depending on the higher burden.
In isolated or high impedance earthed systems the phase-to-earth fault is not the
dimensioning case. Therefore, the resistance of the single secondary wire can always be used
in the calculation for this kind of power systems.
The current transformer ratio is mainly selected based on power system data for example,
maximum load and/or maximum fault current. It should be verified that the current to the
protection is higher than the minimum operating value for all faults that are to be detected
with the selected CT ratio. It should also be verified that the maximum possible fault current is
within the limits of the IED.
The current error of the current transformer can limit the possibility to use a very sensitive
setting of a sensitive residual overcurrent protection. If a very sensitive setting of this function
will be used it is recommended that the current transformer should have an accuracy class
which have an current error at rated primary current that is less than ±1% (for example, 5P). If
current transformers with less accuracy are used it is advisable to check the actual unwanted
residual current during the commissioning.
M11616-3 v2
With regard to saturation of the current transformer all current transformers of high
remanence and low remanence type that fulfill the requirements on the rated equivalent
limiting secondary e.m.f. Eal below can be used. The characteristic of the non remanence type
CT (TPZ) is not well defined as far as the phase angle error is concerned. If no explicit
recommendation is given for a specific function we therefore recommend contacting ABB to
confirm that the non remanence type can be used.
The CT requirements for the different functions below are specified as a rated equivalent
limiting secondary e.m.f. Eal according to the IEC 61869-2 standard. Requirements for CTs
specified according to other classes and standards are given at the end of this section.
The CTs must have a rated equivalent limiting secondary e.m.f. Eal that is larger than or equal
to the required rated equivalent limiting secondary e.m.f. Ealreq below:
Isr æ S ö
E al ³ E alreq = 5 × Iop × × ç R ct + R L + R2 ÷
I pr è Ir ø
EQUATION1380 V2 EN-US (Equation 45)
where:
Iop The primary operate value (A)
RL The resistance of the secondary cable and additional load (W). The loop resistance containing the
phase and neutral wires, must be used for faults in solidly earthed systems. The resistance of a single
secondary wire should be used for faults in high impedance earthed systems.
SR The burden of an IED current input channel (VA). SR=0.020 VA/channel for Ir=1 A and SR=0.150 VA/
channel for Ir=5 A
The CTs must have a rated equivalent limiting secondary e.m.f. Eal that is larger than or equal
to the required rated equivalent limiting secondary e.m.f. Ealreq below:
Isr æ S ö
E al ³ E alreq = 1,5 × Iop × × ç R ct + R L + R2 ÷
Ipr è Ir ø
EQUATION1381 V2 EN-US (Equation 46)
where:
Iop The primary operate value (A)
RL The resistance of the secondary cable and additional load (W). The loop resistance containing the
phase and neutral wires, must be used for faults in solidly earthed systems. The resistance of a single
secondary wire should be used for faults in high impedance earthed systems.
SR The burden of an IED current input channel (VA). SR=0.020 VA/channel for Ir=1 A and SR=0.150 VA/
channel for Ir=5 A
The requirement according to Equation 47 and Equation 48 does not need to be fulfilled if the
high set instantaneous or definitive time stage is used. In this case Equation is the only
necessary requirement.
If the inverse time delayed function is the only used overcurrent protection function the CTs
must have a rated equivalent limiting secondary e.m.f. Eal that is larger than or equal to the
required rated equivalent limiting secondary e.m.f. Ealreq below:
Isr æ S ö
E al ³ E alreq = 20 × Iop × × ç R ct + R L + R2 ÷
I pr è Ir ø
EQUATION1076 V2 EN-US (Equation 47)
where
Iop The primary current set value of the inverse time function (A)
RL The resistance of the secondary cable and additional load (W). The loop
resistance containing the phase and neutral wires, must be used for faults
in solidly earthed systems. The resistance of a single secondary wire should
be used for faults in high impedance earthed systems.
SR The burden of an IED current input channel (VA). SR=0.020 VA/channel for
Ir=1 A and SR=0.150 VA/channel for Ir=5 A
Independent of the value of Iop the maximum required Eal is specified according to the
following:
Isr æ S ö
E al ³ E alreq max = I k max × × ç R ct + R L + R2 ÷
I pr è Ir ø
EQUATION1077 V2 EN-US (Equation 48)
where
Ikmax Maximum primary fundamental frequency current for close-in faults (A)
M11623-4 v3
All kinds of conventional magnetic core CTs are possible to use with the IEDs if they fulfill the
requirements corresponding to the above specified expressed as the rated equivalent limiting
secondary e.m.f. Eal according to the IEC 61869-2 standard. From different standards and
available data for relaying applications it is possible to approximately calculate a secondary
e.m.f. of the CT comparable with Eal. By comparing this with the required rated equivalent
limiting secondary e.m.f. Ealreq it is possible to judge if the CT fulfills the requirements. The
requirements according to some other standards are specified below.
A CT according to IEC 61869-2 is specified by the secondary limiting e.m.f. EALF. The value of
the EALF is approximately equal to the corresponding Eal. Therefore, the CTs according to class
P and PR must have a secondary limiting e.m.f. EALF that fulfills the following:
18.1.7.2 Current transformers according to IEC 61869-2, class PX, PXR (and old
IEC 60044-6, class TPS and old British Standard, class X) M11623-14 v5
CTs according to these classes are specified approximately in the same way by a rated knee
point e.m.f. Eknee (Ek for class PX and PXR, EkneeBS for class X and the limiting secondary voltage
Ual for TPS). The value of the Eknee is lower than the corresponding Eal according to IEC
61869-2. It is not possible to give a general relation between the Eknee and the Eal but normally
the Eknee is approximately 80 % of the Eal. Therefore, the CTs according to class PX, PXR, X and
TPS must have a rated knee point e.m.f. Eknee that fulfills the following:
Current transformers according to ANSI/IEEE are partly specified in different ways. A rated
secondary terminal voltage UANSI is specified for a CT of class C. UANSI is the secondary
terminal voltage the CT will deliver to a standard burden at 20 times rated secondary current
without exceeding 10 % ratio correction. There are a number of standardized UANSI values for
example, UANSI is 400 V for a C400 CT. A corresponding rated equivalent limiting secondary
e.m.f. EalANSI can be estimated as follows:
where:
ZbANSI The impedance (that is, with a complex quantity) of the standard ANSI burden for the specific C class
(W)
UANSI The secondary terminal voltage for the specific C class (V)
The CTs according to class C must have a calculated rated equivalent limiting secondary e.m.f.
EalANSI that fulfils the following:
A CT according to ANSI/IEEE is also specified by the knee point voltage UkneeANSI that is
graphically defined from an excitation curve. The knee point voltage UkneeANSI normally has a
lower value than the knee-point e.m.f. according to IEC and BS. UkneeANSI can approximately be
estimated to 75 % of the corresponding Eal according to IEC 61869-2. Therefore, the CTs
according to ANSI/IEEE must have a knee point voltage UkneeANSI that fulfills the following:
The performance of a protection function will depend on the quality of the measured input
signal. Transients caused by capacitive voltage transformers (CVTs) can affect some
protection functions.
The capacitive voltage transformers (CVTs) should fulfill the requirements according to the IEC
61869-5 standard regarding ferro-resonance and transients. The ferro-resonance
requirements of the CVTs are specified in chapter 6.502 of the standard.
The transient responses for three different standard transient response classes, T1, T2 and T3
are specified in chapter 6.503 of the standard. CVTs according to all classes can be used.
The protection IED has effective filters for these transients, which gives secure and correct
operation with CVTs.
The SNTP server to be used is connected to the local network, that is not more than 4-5
switches or routers away from the IED. The SNTP server is dedicated for its task, or at least
equipped with a real-time operating system, that is not a PC with SNTP server software. The
SNTP server should be stable, that is, either synchronized from a stable source like GPS, or
local without synchronization. Using a local SNTP server without synchronization as primary or
secondary server in a redundant configuration is not recommended.
For PTP to perform properly, the Ethernet equipment that is used needs to be compliant with
IEEE1588. The clocks used must follow the IEEE1588 standard BMC (Best Master Algorithm)
and shall, for instance, not claim class 7 for a longer time than it can guarantee 1us absolute
accuracy.
The merging units that supply the IED with measured values via the process bus must fulfill the
IEC/UCA 61850-9-2LE standard.
This part of the IEC 61850 is specifying “Communication Service Mapping (SCSM) – Sampled
values over ISO/IEC 8802”, in other words – sampled data over Ethernet. The 9-2 part of the
IEC 61850 protocol uses also definitions from 7-2, “Basic communication structure for
substation and feeder equipment – Abstract communication service interface (ACSI)”. The set
of functionality implemented in the IED (IEC/UCA 61850-9-2LE) is a subset of the IEC
61850-9-2. For example the IED covers the client part of the standard, not the server part.
The standard does not define the sample rate for data, but in the UCA users group
recommendations there are indicated sample rates that are adopted, by consensus, in the
industry.
There are two sample rates defined: 80 samples/cycle (4000 samples/sec. at 50Hz or 4800
samples/sec. at 60 Hz) for a merging unit “type1” and 256 samples/cycle for a merging unit
“type2”. The IED can receive data rates of 80 samples/cycle.
Note that the IEC/UCA 61850-9-2LE standard does not specify the quality of the sampled
values, only the transportation. Thus, the accuracy of the current and voltage inputs to the
merging unit and the inaccuracy added by the merging unit must be coordinated with the
requirement for actual type of protection function.
Factors influencing the accuracy of the sampled values from the merging unit are for example
anti aliasing filters, frequency range, step response, truncating, A/D conversion inaccuracy,
time tagging accuracy etc.
In principle the accuracy of the current and voltage transformers, together with the merging
unit, shall have the same quality as direct input of currents and voltages.
AC Alternating current
ACC Actual channel
ACT Application configuration tool within PCM600
A/D converter Analog-to-digital converter
ADBS Amplitude deadband supervision
ADM Analog digital conversion module, with time synchronization
AI Analog input
ANSI American National Standards Institute
AR Autoreclosing
ASCT Auxiliary summation current transformer
ASD Adaptive signal detection
ASDU Application service data unit
AWG American Wire Gauge standard
BBP Busbar protection
BFOC/2,5 Bayonet fiber optic connector
BFP Breaker failure protection
BI Binary input
BIM Binary input module
BOM Binary output module
BOS Binary outputs status
BR External bistable relay
BS British Standards
BSR Binary signal transfer function, receiver blocks
BST Binary signal transfer function, transmit blocks
C37.94 IEEE/ANSI protocol used when sending binary signals between IEDs
CAN Controller Area Network. ISO standard (ISO 11898) for serial
communication
CB Circuit breaker
CBM Combined backplane module
CCITT Consultative Committee for International Telegraph and Telephony. A
United Nations-sponsored standards body within the International
Telecommunications Union.
CCM CAN carrier module
CCVT Capacitive Coupled Voltage Transformer
Class C Protection Current Transformer class as per IEEE/ ANSI
CMPPS Combined megapulses per second
CMT Communication Management tool in PCM600