Professional Documents
Culture Documents
Ra 92701 A10vo
Ra 92701 A10vo
A10V(S)O
open circuit
Contents Features
Ordering code standard range 2 – Axial piston pump A10VO, variable, in swashplate design for
Technical data 4 hydrostatic transmissions in open loop circuit
Unit dimensions combination pumps 29 – Through drive option for multi-circuit system
Dimensions of through drives 30
Installation notes 34
Safety information 35
/36 Bosch Rexroth Corp. | Mobile Hydraulics A10VO | RA 92 701/10.07
Mode of operation
Pump open circuit O
Series
31
Direction of rotation
Viewed on drive shaft clockwise R
counter clockwise L
Seals
NBR nitril-caoutchouc, shaft seal FKM P
FKM fluoro-caoutchouc V
● = available ❍ = in preparation – = not available = preferred program
RA 92 701/10.07 | A10VO Mobile Hydraulics | Bosch Rexroth Corp. /36
A10V(S) O / 31 –
Version
Mode of operation
Size
Control devices
Series
Direction of rotation
Seals
Shaft end
Technical data
Fluid
Prior to project design, please see our data sheets RA 90220 Notes on the selection of hydraulic fluid
(mineral oil ) and RA 90221 (ecologically acceptable fluids) for
In order to select the correct fluid, it is necessary to know the
detailed information on fluids and application conditions. When
operating temperature in the tank (open circuit) in relation to
using ecologically acceptable fluids attention must be paid to
the ambient temperature.
possible limitations of the technical data. If necessary please
contact us. The hydraulic fluid should be selected so that within the ope-
rating temperature range, the viscosity is within the optimum
Operating viscosity range range (νopt.); see shaded section of the selection diagram. We
recommend that the higher viscosity grade is selected in each
For optimum efficiency and service life we recommend that the
case.
operating viscosity (at operating temperature) be selected in
the range Example: at an ambient temperature of X °F (°C) the opera-
ting temperature in the tank is 140 °F (60 °C). In the optimum
νopt = opt. operating viscosity 80...170 SUS (16...36 mm2/s)
viscosity range νopt (shaded area), this corresponds to viscosity
referred to tank temperature (open loop circuit). grades VG 46 or VG 68, VG 68 should be selected.
Important: The leakage oil temperature is influenced by pres-
Limits of viscosity range
sure and speed and is typically higher than the tank tempera-
The following limits are valid for extreme operating conditions: ture. However max. temperature at any point in the system may
not exceed 239 °F (115 °C).
νmin = 60 SUS (10 mm2/s)
short term (t ≤ 1 min) At high temperatures please use FKM seals.
at a max. permissible oil temperature
If the above mentioned conditions cannot be kept due to extre-
of tmax = 239 °F (115 °C).
me operating parameters or high ambient temperatures, please
Please note, that the max. fluid temperature of 239 °F (115 consult us.
°C) is also not exceeded in certain areas (for instance bearing
area). The temperature in the bearing area is approx. 7 °F (5 K) Filtration of fluid
higher than average leakage fluid temperature.
The finer the filtration, the better the achieved cleanliness of
νmax = 7500 SUS (1600 mm2/s) the fluid and the longer the life of the axial piston unit.
short term (t ≤ 1 min)
To ensure a reliable functioning of the axial piston unit, a mini-
on cold start
mum cleanliness of
(tmin = p ≤ 436 psi/30 bar, n ≤ 1000 rpm, -40 °F/40 °C.
20/18/15 acc. to ISO 44061) is necessary.
At temperatures between -13 °F (-25 °C) and -40 °F (-40 °C)
special measures may be required for certain installation positi- At very high fluid temperatures (195 °F (90 oC) up to max.
ons. Please contact us for further information. 239 °F (115 °C)) the minimum cleanliness has to be at least
For detailed information on operation at very low temperatures 19/17/14 acc. to ISO 44061).
see RA 90300-03-B.
If the above cleanliness classes cannot be met please consult us.
When operating at temperatures between 195 °F (+90 °C) and 1)
draft issue 1999
239 °F (115 °C) use FKM-seals (code designation V).
1000
VG
VG 22
VG 32
VG 4
200
10
500 100
6
8
Viscosity ν SUS [mm2/s]
300 60
200 40 36 170
100 20
80 16 80
60 10
Technical data (valid for mineral oil; for ecologically acceptable fluids see RA 90221)
Operating pressure range
0,9 13
Case drain pressure
Maximum pressure of leakage fluid (at ports L, L1): 0,9 0,8 11.5
0,7 0,8 0,9 1,0
maximum 7 psi (0,5 bar) higher than inlet pressure at port S.
Displacement Vg / Vgmax
pL abs max_ ___________________________________29 psi (2 bar)
Direction of flow
S to B.
Table of values (theoretical values, without considering ηmh and ηv: values rounded)
Size 18 28 45 71 100 140
High-Speed-Version 45 71 100 140
Displacement Vg max in
3
1.10 1.71 2.75 4.33 6.10 8.54 2.75 4.33 6.10 8.54
(cm ) 3
(18) (28) (45) (71) (100) (140) (45) (71) (100) (140)
Speed , max.
1)
at Vg max no max rpm 3300 3000 2600 2200 2000 1800 3000 2550 2300 2050
at Vg < Vg max no max perm. rpm 3900 3600 3100 2600 2400 2100 3300 2800 2500 2200
Flow, max.
at no max qvo max gpm 15.6 22.2 30.9 41.2 52.8 66.6 35.7 47.8 60.7 75.8
(L/min) (59.4) (84) (117) (156) (200) (252) (135) (181) (230) (287)
at nE = 1800 rpm qvE gpm 8.5 13.2 21.4 33.8 47.5 66.6 21.4 33.8 47.5 66.6
(L/min) (32.4) (50) (81) (128) (180) (252) (81) (128) (180) (252)
Power (∆p = 4000 psi (280 bar) and Vg max)
at no max Po max HP 37 52 74 98 125 157 84 113 143 180
(kW) (27.7) (39) (55) (73) (93) (117) (63) (84) (107) (134)
at nE = 1800 rpm PE max HP 20 31 51 80 113 158 51 80 113 158
(kW) (15) (23) (38) (60) (84) (118) (38) (60) (84) (118)
Torque at Vg max
∆p = 4000 psi Tmax lb-ft 58.9 91 146 230 324 453 146 230 324 453
(280 bar) (Nm) (80.1) (125) (200) (316) (445) (623) (200) (316) (445) (623)
∆p = 1450 psi T lb-ft 21 33 53 83 117 164 53 83 117 164
(100 bar) (Nm) (28.6) (45) (72) (113) (159) (223) (72) (113) (159) (223)
Moment of inertia J lb-ft 2
0.022 0.040 0.078 0.197 0.396 0.574 0.078 0.197 0.396 0.574
about drive axis (kgm ) 2
(0.00093) (0.0017) (0.0033) (0.0083) (0.0167) (0.0242) (0.0033) (0.0083) (0.0167) (0.0242)
Max. angular acceleration rad/s 6800 5500 4000 2900 2400 2000 4000 2900 2400 2000
Torsional stiffness - shaft "S" lb-ft/rad 8149 16403 27562 52835 89039 124610 27562 52835 89039 124610
(Nm/rad) (11087) (22317) (37499) (71884) (121142) (169537) (37499) (71884) (121142) (169537)
shaft "U" lb-ft/rad 5946 22107 66953 22107 66953
(Nm/rad) (8090) (30077) (91093) (30077) (91093)
shaft "R" lb-ft/rad 19375 30153 56261 30153 56261
(Nm/rad) (26360) (41025) (76545) (41025) (76545)
shaft "W" lb-ft/rad 25330 74858 25330 74858
(Nm/rad) (34463) (101847) (34463) (101847)
shaft "K" lb-ft/rad 9805 19712 32270 60352 99448 144680 32270 60352 99448 144680
(Nm/rad) (13340) (26819) (43905) (82112) (135303) (196844) (43905) (82112) (135303) (196844)
Filling capacity gall. 0.1 0.18 0.26 0.42 0.58 0.79 0.26 0.42 0.58 0.79
(L) (0.4) (0.7) (1.0) (1.6) (2.2) (3.0) (1.0) (1.6) (2.2) (3.0)
Weight (without fluid) m lbs 26 33 46 73 99 132 46 73 99 132
(kg) 12 15 21 33 45 60 21 33 45 60
1
) Values shown are valid for an absolute pressure of 14.5 psi (1 bar) at inlet port S. At reduced displacement or increased inlet
pressure the speed may be increased according to the diagram.
2
) For higher radial loads, please consult us.
RA 92 701/10.07 | A10VO Mobile Hydraulics | Bosch Rexroth Corp. /36
Determination of size
( )
Vg • n • ηv Vg • n • ηv
Flow qv = [gpm] qv = [L/min]
231 1000
( )
Vg • ∆ p Vg • ∆ p
Torque T = [lb-ft] T = [Nm]
24 • π • ηmh 20 • π • ηmh
( )
qv • ∆ p qv • ∆ p
Power P = [HP] P = [kW]
1714 • ηt 600 • ηt
Application of forces
Fq
± Fax
X/2 X/2
X
/36 Bosch Rexroth Corp. | Mobile Hydraulics A10VO | RA 92 701/10.07
Noise Level
Characteristics for pump
Measured in an anechoic chamber
Distance microphone-pump = 3.3 ft (1 m)
Max. measurement error ± 2 dB (A)
Fluid: hydraulic oil ISO VG 46 DIN 51519, t = 122 °F (50° C)
Size 18 Size 28
74 74
qv max qv max
72 72
qv zero
qv zero
Noise level LA [dB(A)]
0 (50) (100) (150) (200) (250)(280)(bar) 0 (50) (100) (150) (200) (250)(280)(bar)
Operating pressure p Operating pressure p
Size 45 Size 71
80 qv max
76 qv max
78
74 qv zero qv zero
qv max
76
72
Noise level LA [dB(A)]
Noise level LA [dB(A)]
qv max
n = 2600 rpm n = 1800 rpm qv zero 74 n = 2200 rpm
70 qv zero
72 n = 1800 rpm
68
70
66
68
64
66
62
64
60
62
58
500 1000 1500 2000 2500 3000 3500 4000 psi 60
0 (50) (100) (150) (200) (250)(280)(bar) 58
Operating pressure p 500 1000 1500 2000 2500 3000 3500 4000 psi
0 (50) (100) (150) (200) (250)(280)(bar)
Operating pressure p
RA 92 701/10.07 | A10VO Mobile Hydraulics | Bosch Rexroth Corp. /36
76
n = 2000 rpm qv max 78
n = 1800 rpm
n = 1800 rpm qv zero 76
74
72 74
70 72
68 70
66 68
64 66
62 64
60 62
500 1000 1500 2000 2500 3000 3500 4000 psi
60
0 (50) (100) (150) (200) (250)(280)(bar) 500 1000 1500 2000 2500 3000 3500 4000 psi
Operating pressure p 0 (50) (100) (150) (200) (250)(280)(bar)
Operating pressure p
10/36 Bosch Rexroth Corp. | Mobile Hydraulics A10VO | RA 92 701/10.07
Size 18
(L/min) gpm (kW) HP
– – – – n = 1500 rpm
(80) 20 (40)
_____ n = 3300 rpm (60) (30) 40
Flow qv
Drive power P
qvq Pqvmax
Pqv
(40) 10 v max (20)
20
(20) PP
qvqvzero
zero (10)
Drive power P
(40) 10 (20)
20
(20) Pqv zero (10)
0 psi0
500 1000150020002500300035004000
0 (50) (100) (150) (200) (250)
(280)(bar)
Operating pressure p
Size 45 (L/min)gpm (kW) HP
– – – – n = 1800 rpm (120) (60) 80
30
_____ (100) qv (50)
n = 2600 rpm
60
Drive power P
Flow qv
(80) 20 (40)
(60) (30) 40
Pqv max
(40) 10 (20)
Pqv zero 20
(20) (10)
0 psi0
500 1000150020002500300035004000
0 (50) (100) (150) (200) (250)
(280)(bar)
Operating pressure p
Size 71 (L/min)gpm (kW) HP
– – – – n = 1800 rpm (160) (80)
40 100
_____ n = 2200 rpm (140) qv (70)
Drive power P
Flow qv
(120) 30 (60) 80
(100) (50)
60
(80) 20 Pqv max (40)
(60) (30) 40
(40) 10 Pqv zero (20)
20
(20) (10)
0 psi0
500 1000150020002500300035004000
0 (50) (100) (150) (200) (250)
(280)(bar)
Operating pressure p
RA 92 701/10.07 | A10VO Mobile Hydraulics | Bosch Rexroth Corp. 11/36
Flow qv
Drive power P
– – – – n = 1800 rpm
50
_____ (180) (90) 120
n = 2000 rpm
(160) qv (80)
40 100
(140) (70)
(120) Pqv max (60) 80
30
(100) (50)
60
(80) 20 (40)
(60) (30) 40
(40) 10 Pqv zero (20)
20
(20) (10)
0 psi 0
500 1000150020002500300035004000
0 (50) (100) (150) (200) (250) (280)(bar)
Operating pressure p
Drive power P
(240) qv (120) 160
60
(220) (110)
140
(200) (100)
50
(180) (90) 120
(160) Pqv max
(80)
40 100
(140) (70)
(120) (60) 80
30
(100) (50)
60
(80) 20 (40)
(60) (30) 40
(40) 10 Pqv zero (20)
20
(20) (10)
0 psi 0
500 1000150020002500300035004000
0 (50) (100) (150) (200) (250)
(280)(bar)
Operating pressure p
Overall efficiency
qv • p qv • p
ηt =
Pqv max • 1714 (Pqv max
• 600 )
Volumetric efficiency
qv
ηv =
qv theor.
12/36 Bosch Rexroth Corp. | Mobile Hydraulics A10VO | RA 92 701/10.07
This will supply the control piston directly with control oil; a
minimum pressure of pst ≥ 725 psi (50 bar) is required.
The pump can only be switched between Vg max or Vg min . B
Operating pressure pB
RA 92 701/10.07 | A10VO Mobile Hydraulics | Bosch Rexroth Corp. 13/36
Size 140
Size 140
View Z
Size A1 A2 A3 A4 A5 A6
A7 A8 X (closed)
28 7.62 (193.5) 7.48 (190) 0 (0) 2.16 (55) 6.22 (158) 3.94 (100) 4.07 (103.5) 0.12 (3) R1/4in DIN 3852-1
45 8.37 (212.5) 8.23 (209) 0.12 (3) 2.50 (63.5) 6.81 (173) 4.33 (110) 4.47 (113.5) 0.12 (3) R1/4in DIN 3852-1
71 9.70 (246.5) 9.55 (242.5) 0.12 (3) 2.89 (73.5) 7.91 (201) 4.86 (123.5) 5.02 (127.5) 0.12 (3) R1/4in DIN 3852-1
100 12.26 (311.5) 12.11 (307.5) 0.12 (3) 3.19 (81) 10.55 (268) 5.06 (128.5) 5.22 (132.5) 0.12 (3) R1/4in DIN 3852-1
140 13.31 (338) 13.15 (334) 0.12 (3) 3.70 (94) 10.55 (268) 5.92 (150.5) 6.10 (155) 0.12 (3) M14x1,5 DIN 3852-1
14/36 Bosch Rexroth Corp. | Mobile Hydraulics A10VO | RA 92 701/10.07
DR - Pressure control
The pressure controller serves to maintain a constant pressure Circuit drawing
in a hydraulic system within the range of the pump. The pump Size 18 ... 100
therefore supplies only the amount of hydraulic fluid required
by the system. Pressure may be steplessly set at the pilot valve.
B
Static characteristic
(at n1 = 1500 rpm; toil = 122 °F / 50 °C)
qv max
S L1 L
Flow qv
qv min B
290 psi 4000 psi
(20 bar) Operating pressure p (280 bar)
Dynamic characteristic
The opening curves are mean values measured under test
conditions with the unit mounted inside the tank.
Conditions: n = 1500 rpm
toil = 122 °F (50 °C)
Main relief set at 5100 psi (350 bar)
Ports
Stepped loading by suddenly opening or closing the pressure S L1 L
B Pressure port
line using a pressure relief valve at 3.3 ft (1 m) downstream
from the pump pressure outlet. S Inlet port
psi (bar) L,L1 Case drain port (L1 plugged)
5100 (350)
435 (300)
Controller data
Operating pressure p
360 (250) Hysteresis and repetitive accuracy ∆p ____ max. 45 psi (3 bar)
0 Control times
Vgmax tSA [ms] tSA [ms] tSE [ms]
Size against 725 psi against 3200 psi zero stroke 4000 psi
Displacement
(swivel angle)
Size 140
NG A1 A2 A3 A4
18 - - 4.96 (126) 4.13 (105)
28 4.29 (109) 8.86 (225) 5.35 (136) 4.17 (106)
45 4.17 (106) 9.61 (244) 5.75 (146) 4.17 (106)
71 4.17 (106) 10.94 (278) 6.30 (160) 4.17 (106)
100 4.17 (106) 13.54 (344) 6.50 (165) 4.17 (106)
140 5.00 (127) 13.35 (339) 6.65 (169) 5.00 (127)
16/36 Bosch Rexroth Corp. | Mobile Hydraulics A10VO | RA 92 701/10.07
Static characteristic
S L1 L
(at n1 = 1500 rpm; toil = 122°F / 50°C)
Hysteresis and pressure rise ∆p Size 140 not included in scope of supply
qv max
X
Flow qv
Setting range
qv min
290 psi 4000 psi
(20 bar) Operating pressure p (280 bar)
Control data
Hysteresis ∆p ________________________ max. 45 psi (3 bar) S L1 L
Static characteristic
(at n1 = 1500 rpm; toil = 122 °F / 50 °C)
qv max
S L1 L
Setting range
Size 140
qv min not included
290 psi 4000 psi in scope of
(20 bar) Operating pressure p (280 bar)
supply with DFR1
Static characteristic at variable speed plugged
Flow qv
speed n
Dynamic characteristic operating curve
Ports
The curves shown are measured average values under test
conditions. B Pressure port
psi (bar)
100 5100 (350) S Inlet port
L,L1 Case drain port (L1 plugged)
435 (300)
400 (280) X Pilot pressure port
75
360 (250)
Load pressure
Displacement Vg %
0
260 (18) Standard setting: 200 psi (14 bar). If a different setting is
Control time (stand by)
required please state in clear text.
When port X is loaded to tank (and outlet B is closed), a zero
Stroking time tSA Destroking time tSE
stroke pressure (standby) of p = 260 + 30 psi (18 + 2 bar)
tSA [ms] tSE [ms] tSE [ms] results. (depends on ∆p)
Size 4000 psi 4000 psi 725 psi
(280 bar)-stand by (280 bar)-stand by (50 bar)-stand by
Control data
Z
Position of valve for
clockwise rotation
Static characteristic
Maximum B
power curve
75
50
S L1 L
Minimum
power curve
25 Size 140
not included
in scope of
0 725 1450 2200 2900 3600 4000 4350 psi supply
(50) (100) (150) (200) (250) (280)(300) (bar)
Operating pressure p
Ports
B Pressure port
S Inlet port
L,L1 Case drain port (L1 plugged)
X Pilot pressure port
RA 92 701/10.07 | A10VO Mobile Hydraulics | Bosch Rexroth Corp. 21/36
Size 140
Size 140
View Z
1 .87 (47.6)
0.79 (20)
Flange SAE J744
1)
L
(1
B
43
82-2 (A)
DIA 3.2479(Ø82.55)h8
2.48 (63)
0.
7)
(6
0.87 (22.2)
64
3.2500
2.
2.48 (63)
2.60 (66)
2.52 (64)
View V
2.06 (52.4)
0.98 (25)
0.45 (11.5)
1.69 (43)
L1
4.19 (106.4) S
5.98 (152)
5.71 (145)
mech. displace-
7.68 (195)
ment limiter 1.03 (26.2)
W
Centering3)
R3.15x6.7 DIN332
Ø 3/4 in
0.87 (22)
1.18 (30)
0.62 (15.8)
1.50 (38)
0.94 (23.8)
1.25 (31.8)
Version 61 N00
Service ports at rear, no through drive (without control valves)
6.69(170)
0.37(9.5) 3.54(90) 1.87(47.6)
0.87(22.2)
0.79(20)
0.25(6.3)
1.77(45)
4.0000 DIA (ø101.6 )
h8
)
(14
55
0.
6.8
2.95(75)
5 (17
3.9979
4)
4)
(7
91
1.77(45)
2.
1.19(30.2)
Flange SAE J744
101-2 (B) 1.25(32)
0.55(14) 5.75(146)
2.31(58.7)
1.57(40) 6.22(158)
Version 62 N00
Service ports on side, no through drive
2.31 (58.7)
1.87 (47.6)
0.79 (20)
1.26 (32)
6.48 (164.5)
7.64 (194) 6.57 (167)
1.19 (30.2) 0.87 (22.2)
(24)
(19,024)
(3-0,2) 0.251(6,35+0,025)
0.250
A
– 0,006 ) DIA 0.863
0.251(6,35+0,025)
(21,91)
0.130(3,2+0,1)
B
0.250
0.126
(21,774 +0,006
DIA0.8575
0.8570
Version 61 N00
Service ports at rear, no through drive (without control valves)
1.03(26.2)
0.98(25)
1.97(50)
4.0000 DIA (ø101. 6 )
h8
4)
(1
55
0.
3.17(80.5)
3.9979
3)
(8
1.97(50)
7
Flange SAE J744 .2
1.40(35.7)
3
101-2 (B)
0.55(14) 5.75(146) 1.57(40)
1.77(45) 7.13(181)
2.75(69.9)
Version 62 N00
Service ports on side, no through drive
0.98 (25)
3.54 (90) 3.54 (90)
2.06 (52.4)
2.75(69.9)
1.57(40)
7.24(184)
8.62 (219) 7.36(187)
9,
Version 91 N00
Service ports at rear, no through drive (without control valves)
0.50(12.7) 8.78(223)
2.06(52.4)
0.24(6) 4.53(115) 1.03(26.2)
2.28(58)
)
0.98(25)
18
1(
5.0000DIA (ø127 )
7
h8
0.
8.2
7(21
0)
3.62(92)
98
4.9975
(
86
3.
2.28(58)
Flange SAE J744
1.69(42.9)
127-2 (C)
0.71(18)
2.09(53) 7.13(181) 1.97(50)
8.07(205) 3.06(77.8)
Version 92 N00
Service ports on side, no through drive
0.98 (25)
4.09(104)
1.03 (26.2)
3.06 (77.8)
1.97 (50)
4.09(104)
(3,2) (28,6)
0.16 (4) 0.3136(7,94+0,025)
in
0.3126
A
1-12UNF-2A
0.3136(7,94+0,025)
DIA 1.25
(27,385)
(31,75)
0.1394(3,54–0,1)
B
0.3126
0.1354
0.56 0.12
(14,1) (3)
(31,51)
1.18 Taper
(30) 125:1000
1.37
(34,9)
2.61
(66,4)
Unit dimensions, Size 100 Before finalizing your design please request
a certified installation drawing.
Dimensions in inches (mm).
Version 61 N00
Service ports at rear, no through drive (without control valves)
1.25(31.8)
(10 1.26(32)
0.24(6) 6.89(175)
4.17
5.0000 DIA (ø127 )
h8
2.16(55) 2.16(55)
5.98(152)
0.69(17.5)
3.66(93)
3.94(100)
4.9975
2.00(50.8)
0.79(20)
7.13(181)
Flange SAE J744 3.74(95) 2.36(60)
8.27(210)
127-2 (C)
9.29(236) 3.50(88.9)
Version 62 N00
Service ports on side, no through drive
1.26 (32)
3.94(100)3.94(100)
2.63 (66.7)
3.50 (88.9)
10.83 (275)
12.48 (317) 9.29 (236)
in
Unit dimensions, Size 140 Before finalizing your design please request
a certified installation drawing.
Dimensions in inches (mm).
Version 61 N00
Service ports at rear, no through drive (without control valves)
)
.5
1.25(31.8)
18
0.25(6.4) 6.81(173) 1.26(32)
(1
66
4.
6.0000 DIA (ø152.4 )
h8
4.41(112) 4.29(109)
2.36(60) 2.36(60)
6.36(161.6)
7.87(200)
4.25(108)
5.9975
2.00(50.8)
0.83(21) 0.79(20)
3.07(78) 6.36(161.6) 2.48(63)
Flange SAE J744 7.87(200) 3.50(88.9)
152-4 (D) 10.31(262)
Version 62 N00
Service ports on side, no through drive
10.83 (275 )
View W View V
2.48 (63)
26 (32)
4.33(100) 4.33(100)
2.63 (66.7)
3.50 (88.9)
1.
2.00 (50.8) 1.25 (31.8)
Through drives
Axial piston units A10V(S)O can be supplied with a through drive as shown in the ordering code on page 3. The type of through
drive is determined by codes (K01–K24). If the combination pump is not mounted in the factory, the simple type code is sufficient.
Included in this case are: Shaft coupler, seals, and if necessary an adapter flange.
Ttot Tthr
The drive torques for pump 1 and pump 2 can be split up as required. However the max. permissible input torque Ttot as well as
the max. permissible through drive torque Tthr may not be exceeded.
l3
Weight m lbs (kg) 26 (12) 33 (15) 46 (21) 73 (33) 99 (45) 132 (60)
Distance to center of gravity l1 in (mm) 3.54 (90) 4.33 (110) 5.11 (130) 5.91 (150) 6.30 (160) 6.30 (160)
RA 92 701/10.07 | A10VO Mobile Hydraulics | Bosch Rexroth Corp. 29/36
Overview of through drive mounting options Before finalizing your design please request
a certified installation drawing.
Dimensions in inches (mm).
.5)
(ø82.55+0.020)
+0.050
06
(ø1
3.2520
DIA 3.2508
9
4.1
DIA
0.39 (10)
B A5 to pump mounting face A1
45 Section A - B
A °
A4
A3
(ø82.55+0.020)
9
+0.050
4.1
DIA 6.5)
3.2520
DIA 3.2508
0
(ø1
0.39 (10)
B A5 A2
to pump mounting face A1
)
46
(ø1 A5
+0.020 )
(ø101.6 +0.050
DIA 4.0020
4.0008
5
5.7
A
DI
0.39 (10)
B Not with size 28 A2
to pump mounting face A1
)
46
(ø1
+0,020 )
(ø101,6 +0,050
4.0020
DIA 4.0008
5
5.7
DIA A5
0.39 (10)
B A2
to pump mounting face A1
Not with
size 71 Not with size 71
1)
)
(ø18
(ø127 +0.050
+0.020
5.0020
DIA 5.0008
7.13
DIA
B 0.51 (13)
A2
A5 to pump mounting face A1
1)
(ø18
+0.020 )
(ø127 +0.050
5.0020
DIA 5.0008
7.13
DIA
A5
B
0.51 (13)
to pump mounting face A1
+0.02 )
(ø152.4+0.07
DIA 6.0008
6.0027
B
M16 ; 0.83 (21) deep
0.51 (13)
13.78 (350)
to pump mounting face
Installation notes
Optional installation position. The pump housing must be filled ρ • l • dv
∆p1 = • 10–5 [bar] ρ = density [kg/m3]
with fluid during commissioning and operation. dt
l = pipe lenth [m]
In order to attain the lowest noise level, all connections dv/dt = rate of change in fluid
(suction, pressure, pilot, case drain) must be linked by flexible velocity [m/s2]
members to tank. ∆p2: Pressure loss due to static head
Avoid placing a check valve in the case drain line. In some ∆p2 = h • ρ • g •10–5 [bar] h = height [m]
cases it may be permissible however. Please consult us. ρ = density [kg/m3]
The largest standard pipe connection must be installed in the g = gravity. = 9,81 m/s2
uppermost (top) leakage port.. ∆p3: line losses (elbows etc.)
1. Vertical installation (shaft end upwards) 2. Horizontal installation
Following installation conditions must be taken into account: The pump must be installed in such a manner, that either "L" or
1.1 Arrangement inside the reservoir "L1" is at the top.
Before installation fill pump housing, keeping it in a horizontal 2.1 Arrangement inside the reservoir
position. a) If the min. fluid level is above the top of the pump:
a) If the min. fluid level is equal to or above the pump mounting Close "L1" , "L" and "S" open, mount suction pipe to port S,
surface: and pipe "L" at least 8 in (200 mm) away from suction pipe
Close port "L", "L1" and "S" open; L1 piped and also S with (see fig. 3).
suction pipe (see fig. 1). b) If the min. fluid level is equal to or below the top of the pump:
b) If the min. fluid level is below the pump mounting surface: Pipe port "L" and "S" acc. to fig. 4 , port "L1" closed. Condi-
pipe port "L" and "S" acc. to fig. 2. Conditions acc. to item tions correspond with item 1.2.1.
1.2.1, close port "L".
Note: In order to avoid demages at the pump, all attached
Note: In order to avoid damages at the pump, all attached parts (e.g. protective caps) must be removed.
parts (e.g. protective caps, covers, etc.) must be removed
before installation. Fluid
L min. 200 mm
Fluid
ht min
L
L1 L1 S
Fig. 3
min. 200 mm S Fig. 1 2.2 Arrangement outside the reservoir
1.2 Arrangement outside the reservoir Fill pump housing before commissioning.
Before installation fill pump housing, keeping it in a horizontal
position. For mounting above the tank see fig. 2.
Limiting condition:
1.2.1 Min. pump inlet pressure pabs min = 11.6 psi (0.8 bar) under L S
static and dynamic loading.
Note: Avoid mounting above tank wherever possible in order to
attain a low noise level. Fluid
h max
pressure loss, but may not be greater than hmax = 31.5 in/800 mm)
(Immersion depth ht min = 7.8 in/200 mm). Baffle Fig. 4
L
L1
S
Fluid
ht min
h t min h max
Fluid
Baffle
Baffle
L1
Fig. 2
S
Overall pressure loss
∆pGes = ∆p1 + ∆p2 + ∆p3 ≤ (1 – pabs min) = 3 psi (0.2 bar)
∆p1: Pressure loss in pipe due to accelerating column of fluid L Fig. 5
RA 92 701/10.07 | A10VO Mobile Hydraulics | Bosch Rexroth Corp. 35/36
Safety information
– Pump A10V(S)O was designed for operation in open loop circuits.
– Systems design, installation and commissioning require trained technicians or tradesmen.
– All hydraulic ports can only be used for the fastening of hydraulic service lines.
– Tightening torques:
The tightening torques mentioned in this data sheet are maximum values and must not be exceeded (max. values for thread).
Manufacturer's information concerning the maximum permitted tightening torques of the various fittings are to be observed!
For ISO 68 mounting bolts, we recommend that tightening torques be checked on a case by case basis in accordance with
VDI 2230, published 2003.
– During and shortly after operation of a pump the housing and especially a solenoid can be extremely hot, avoid being burned!
36/36 Bosch Rexroth Corp. | Mobile Hydraulics A10VO | RA 92 701/10.07