Professional Documents
Culture Documents
ABB ATEX Jargon Buster
ABB ATEX Jargon Buster
ABB’s ATEX jargon buster explains the terminology users are likely to encounter
when purchasing equipment for hazardous areas. If you have a specific ATEX
question, please send an email to [email protected].
ABB’s ATEX Jargon Buster uses hyperlinks for quick navigation. A click on any
underlined word takes you straight to the relevant entry. Alternatively, use the Quick
Navigation Tool below to select a relevant section.
A
Apparatus Group
There are two apparatus groups for gas/vapour environments:
Group I covers the use of equipment in underground mining environments where
methane is present.
Approval
Equipment is approved for use in hazardous areas by accredited testing laboratories
known as Notified Bodies or by the manufacturers. To qualify for ATEX approval,
manufacturers must show that their products incorporate measures to prevent the
ignition of unavoidable explosive atmospheres.
Area classification
The process by which sources of leak of flammable gas, liquid, mist or combustible
dust are identified, the frequency and duration of those leaks determined and the
extent to which those leaks will travel before they become non-flammable. The area
(strictly a volume) is then marked on a drawing showing the Zones and their extents.
AS2380.9:1991
Australian standard, equivalent to Zone 2 in ATEX terminology.
ATEX
ATEX is an acronym of the French Atmospheriques Explosives. This European
Directive amends and adds safety requirements for hazardous areas in the relevant
national legislation in the member states of the European Union, bringing in a
common standard. The purpose is to enable the sale of equipment across the
European Union, without manufacturers having to satisfy different requirements for
each national market.
Compliance with the ATEX Directive means reinforced safety aspects – safer design,
more demanding testing procedures, and specific quality assurance measures for the
design as well as the manufacturing process. It requires employers to protect both
staff and local communities from the risk of an explosive atmosphere.
ATEX consists of two parts: ATEX 95, which concentrates on the duties of the
manufacturers; and ATEX 137, which focuses on the end users’ obligations.
The ATEX 95 Directive is implemented into UK Law by the The Equipment and
Protective Systems Intended for use in Potentially Explosive Atmospheres
Regulations 1996 (EPS Regulations) making compliance with the ATEX directive
mandatory from July 1st 2003.
The ATEX system depends on three key elements: Harmonised technical standards;
Audits of the manufacturing facilities; and notification by the European Commission
to recognise bodies and test laboratories known as Notified Bodies.
See also http://www.dti.gov.uk/strd/atex.htm.
ATEX 95
The product directive 94/9/EC, known as the ATEX 95 Directive, concentrates on the
manufacturer’s duties, giving the safety requirements to be fulfilled by all equipment,
both electrical and non-electrical, installed in hazardous areas within the European
Union. It describes the Essential Healthy and Safety Requirements (EHSRs) of the
products regarding their design, manufacturing process, testing, documentation and
maintainability.
The requirements are divided into three categories: Technical requirements from
harmonised European standards; health and safety aspects; and production quality
requirements.
Voluntary since 1994, the requirements of the Directive will be mandatory from 1 July
2003. The Directive covers any electrical or mechanical product that contains or
constitutes a potential ignition source and which requires a special design or
installation procedure to prevent an explosion. Regulated equipment includes control
and communication devices, monitoring and detection equipment. It also includes
safety or control devices installed outside hazardous areas that have an explosion
protection function, such as pressure-relief panels and fast-acting shutoff valves.
ATEX 100a
See ATEX 95. ATEX 100 originally covered the product directive until it was re-
classified as ATEX 95 by the Treaty of Amsterdam.
ATEX 137
The “worker protection directive” 1999/92/EC, ATEX 137, describes the “minimum
requirements” for improving the health and safety of workers potentially at risk. It
classifies the environment into zones and outlines which category of equipment can
be used in each zone.
The directive focuses on the analysis and description of the risks, the zone
definitions, and the maintenance practices in relation to site safety. The safety of an
installation in a hazardous area is the result of co-operation between the equipment
manufacturer, the installer and the end user.
ATEX 137 concentrates on the duties of the end user. Workers should be trained on
hazardous area issues by the employer. Authorisation should be given to each
employee working in a hazardous area. Explosion protection measures should be
taken and an explosion protection document (EPD) can be established (an EPD is
not specifically required by the DSEAR Regulations, though verification of the
explosion safety of an area is required before first use and sufficient documentation
to show area classification, required equipment for safe working, and aims of co-
ordination of measures to protect employees) . When equipment is repaired, the end
user has the responsibility to select an appropriate repair shop (see Baseefa
Certification Limited).
The Employers’ obligations in relation to ATEX include assessing the site’s Sources
of Hazard and likely sources of ignition, classification of the area into zones and
marking all points of entry, as well as producing and maintaining documentation. The
main obligations relating to employers are:
Essentially, the employer is required to take all reasonable measures to prevent the
formation of an explosive atmosphere in the workplace. Where this is not possible,
measures must be taken to avoid the ignition of any potentially explosive
atmosphere. In addition, the effects of any explosion must be minimised in such a
way that workers are not put at risk.
Atmosphere
For ATEX purposes, atmospheres are categorised into two classifications: “G” for
explosive gas and “D” for combustible dust. A product certified for both gas and dust
is marked G-D.
Audit
A new feature of the ATEX Directive is that the manufacturer now also needs a
quality system in place that must be checked by the Notified Body. The audit of the
manufacturing facility responsible for delivering Ex equipment is one of the three key
elements in the ATEX system. The other two are the harmonised standards for
equipment; and notification by the European Commission to recognise bodies and
test laboratories as Notified Bodies.
Authorised body
North American terminology. Electrical equipment used in hazardous locations,
classified according to North American rules, must be approved by an authorised
body or the manufacturer.
B
BASEEFA (2001)
UK based testing institute. Notified Body.
C
Canadian Electric (CE Code)
The general description of hazardous areas and protection types in Canada are
presented in Canadian Electric (CE Code) published by CSA. More specific
requirements can be found e.g. from several IEEE and UL publications. Electrical
equipment used in hazardous locations, classified according to North American rules,
must be approved by an authorised body or the manufacturer. The equipment for
Division 1, Zone 0 or Zone 1 areas must always be approved by an authorised body
e.g. UL, CSA or FM.
Category
Hazardous area equipment is allocated a Category depending on its degree of
protection, indicating where the item can be used.
Category 1
Equipment designed for very high level of safety. Requires two independent means
of protection or safe operation with two separate faults. Used where explosive
atmospheres are present continuously or for lengthy periods, typically Zone 0 and
Zone 20.
Category 2
Equipment designed for a high level of safety. Requires the design to be safe with
frequently occurring disturbances or with one operating fault. Used where explosive
atmospheres are likely to occur, typically Zone 1 and Zone 21.
Category 3
Equipment designed for a normal level of safety. Used where explosive atmospheres
are likely to occur infrequently and to be of short duration, typically Zone 2 and Zone
22.
CE Code
See Canadian Electric.
CE Marking
The CE-Marking affixed to the product is a manufacturer’s statement
that the product complies with all relevant Directives. The CE mark
shows that the product has been manufactured according to a certain
design and procedure and acts like a passport that allows a product to
be installed anywhere in the EU. It provides reassurance for buyers
both inside and outside the EU that the equipment conforms to the latest standards.
For ATEX compliance, the CE Marking must appear prominently on each item of
equipment or each protective system.
In principal there only should be one CE mark on an item which shows compliance
with all relevant Regulations. Compliance for Machinery is required under the Supply
of Machines (Safety) Regulations 1992. (See Declaration of conformity).
Certificates
See Declaration of Conformity.
CESI
Testing institute based in Italy. Notified Body.
Chemical Agents Directive (CAD)
Under the Chemical Agents Directive (Directive 98/24/EC), employers have an
obligation to ensure the health and safety of workers and others who may be at risk
from exposure to dangerous chemical substances that can cause fire, explosions or
similar energy releasing events, including runaway chemical reactions.
Classification societies
Organisations that verify the technical standards of ships. Requirements on
instrumentation equipment may vary from one classification society to the next.
Combustible dust
Combustible dust can be in cloud form as a dust/air mixture with a cloud ignition
temperature, or as a layer of dust of a specified thickness with a layer ignition
temperature. The ignition temperature for various types of dust is available from
commercially available tables.
Conductive dust
If the atmosphere contains conductive dust, only electrical equipment approved by a
Notified Body may be installed. If the dust is not conductive and the area is classified
Zone 22, electrical equipment approved by the manufacturer for use in dust
atmospheres can be installed.
Co-operation
Co-operation is a cornerstone of ATEX 137. The safety of an installation in a
hazardous area is the result of a co-operation of the equipment manufacturer, the
installer and the end user.
CSA
The Canadian Standards Association.
D
D
D on the nameplate indicates that the marking relates to dust. A product certified for
both gas and dust is marked G-D.
DEMKO
Testing institute based in Denmark. Notified Body.
DIP
See Dust ignition proof
Directive 1999/92/EC
See ATEX 137
Directive 1994/9/EC
See ATEX 95
Directive 94/9/EC
See ATEX 95
Directive 99/92/EC
See ATEX 137
Division system
An old U.S. system, which defines areas according to the so-called Division system
(NEC 500). It will soon be replaced by the new NEC 505 standard, similar to the IEC
standard.
Dresden Agreement
In 1996, IEC and CENELEC reached a co-ordination agreement to develop new
standards, called the 'Dresden Agreement'. It means that since September 1996 the
same document is submitted to IEC and CENELEC simultaneously and the
standards are published at the same time and are identical. This work stopped
between 1998-2000 due to differences in the IEC and CENELEC definitions of some
of the dust zones. The procedure was re-introduced in 2001, which means that the
IEC standards will be updated over the coming years in accordance with the EHSRs
of the ATEX Directive.
DSEAR
The Dangerous Substances and Explosive Atmospheres Regulations is the UK
implementation of the European ATEX 137 Directive and parts of the Chemical
Agents Directive (CAD). It comes into force in July 2003 and lays down strict new
guidelines governing potentially explosive atmospheres in plants throughout the UK.
It incorporates both the flammable/explosive elements of both the Chemical Agents
and ATEX Directives. The essence of DSEAR is to ensure the safety of employees
and public from dangerous substances that can cause explosions or fires.
The DSEAR regulations deal with explosions and fires caused by dangerous
substances, whether the explosive atmosphere is generated by gases, vapours or
dusts. The new 17 part regulations replaces certain older UK safety legislation e.g.
The Highly Flammable Liquids & Petroleum Gases Regulations of 1972.
DSEAR applies to all industrial and commercial premises where a dangerous
substance is present or is likely to be present during the working day. Offshore
facilities and domestic dwellings are excluded from the regulations.
Dust
With ATEX, combustible dust is for the first time included specifically in the
regulations governing hazardous atmospheres. Typical applications include handling
of grain, coal, sugar, wood and some chemical substances such as sulphur.
Dust cloud
The risk of explosion in a hazardous area with combustible dust is either caused by a
cloud of dust or a layer of dust. It is the responsibility of the user to stage
maintenance periods so that the dust layer on equipment does not build up above
5mm. The ignition temperatures for various types of dust are available from
commercially available reference tables.
E
EECS
UK based testing institute. HSE closed EECS in 2002. Most of the work is now
undertaken by BASEEFA (2001). Notified Body.
EEx
Designation showing that the equipment has been designed to safeguard against the
risk of explosion. This designation will be expanded to include details of the Types of
Protection incorporated. The marking will also indicate the type of potentially
explosive atmosphere in which the equipment may be used (see Apparatus Group)
and the maximum safe operating temperature for different applications (see
Temperature Class).
EExd
Flameproof, for Zone 1. The enclosure of this type of equipment will prevent an
internal explosion, or flame, from being transmitted to the explosive atmosphere
surrounding the machine, hence the name flameproof. The enclosure must withstand
any pressure levels caused by such an internal explosion. The designation under
ATEX for this type of equipment is EExd, which supersedes the earlier designation
Exd.
EExi
Equipment carrying this mark is certified intrinsically safe in accordance with
standard EN 50020.
EExia
This category of equipment can be used in Zone 0, Zone 1 and Zone 2 hazardous
areas.
EExib
Equipment in this category can only be used in Zone 1 and Zone 2 hazardous areas.
EExn
Equipment designated EExn to EN 50021 can only be used in Zone 2.
EExp
See Pressurised Enclosure.
EHSR
See Essential Health and Safety Requirements.
Employers’ obligations
See ATEX 137. Also PUWER.
EN 1127-1: 1997
Harmonised standard CEN EN 1127-1: 1997 covers explosion prevention and
protection.
EN 13463-1:2001
This standard sets out the basic methods and requirements for non-electrical
equipment for use in potentially explosive atmospheres.
EN 50014: 1998
Harmonised standard CENELEC EN 50014: 1998 covers the general requirements
for electrical apparatus for potentially explosive atmospheres.
EN 50018: 2000
Harmonised standard CENELEC EN 50018: 2000 covers the requirements for
flameproof enclosure, 'd'.
EN 50020
This standard sets down guidelines for the construction and testing of intrinsically
safe apparatus intended for use in potentially explosive atmospheres of gas, vapour
or mist, and for associated apparatus (located outside the hazardous area or
protected by another type of protection listed in EN 50014:1998) which is intended for
connection to intrinsically safe circuits which enter such atmospheres.
The standard identifies which clauses of EN 50014 are applicable to intrinsically safe
equipment, and to associated equipment.
EN 50021
Harmonised standard CENELEC EN 50021 covers the requirements of EExn
apparatus for use in Zone 2.
EN 50281-2-1: 1998
Harmonised standard CENELEC EN 500281-2-1: 1998 covers the test methods for
determining the minimum ignition temperatures of dust.
EN - European Norm
A unified set of standards has been developed in the European Union. The goal is to
have standards, which are accepted, and adopted, by all European countries. These
European standards are commonly referred to as the European Norm (EN). The
European standards bodies provide the leadership for the development of these
standards.
End user
The duties of the end user company are outlined by the ATEX 137 directive.
EPD
See explosion protection document.
Equipment category
See Category.
EPS requires that, after 30 June 2003, the responsible person (usually a
manufacturer or their authorised representative) who places equipment on the
market or puts equipment into service, has ensured that the essential health and
safety requirements for the equipment have been satisfied. This includes carrying out
the relevant conformity assessment procedure and application of the CE mark. EPS
does not affect equipment that is already in use on offshore installations on 30 June
2003.
EPS applies to fixed offshore installations but not to seagoing vessels and mobile
offshore units together with equipment on board such vessels or units. EPS
therefore excludes FPSOs and floating production platforms (FPPs), as well as
MODUs, flotels and other mobile units.
European standards
The European standards for ATEX are issued by the European Standards Bodies:
CEN - European Committee for Standardization; and CENELEC - European
Committee for Electro technical Standardization. These bodies produce harmonised
standards to cover the electrical and mechanical fields and give the technical means
to achieve the objectives of EHSRs stated in the ATEX Directives. In 1996, IEC and
CENELEC made a co-ordination agreement to develop new standards called the
'Dresden agreement'. It means that since September 1996 the same document is
submitted to IEC and CENELEC simultaneously and the standards are published at
same time and are identical.
These bodies meet within three European organizations, which are also private:
CEN, the European Committee for Standardization, working in all fields except the
electrotechnical field and telecommunications; CENELEC, the European Committee
for Electrotechnical Standardization, and ETSI, the European Telecommunications
Standards Institute.
Ex
See EEx.
Ex d
See EExd.
Ex i
See EExi.
Ex ia
See EExia.
Ex ib
See EExib.
Ex mark
The Ex mark is the European Commission mark for
products approved for hazardous areas.
Ex n
See EExn
Ex Notified Body Group (ExNBG)
Hazardous area products are approved by the Notified Bodies, known collectively as
the Ex Notified Body Group (ExNBG). These are test laboratories approved, or
’notified’, by the European Commission. Under the old directives, these were referred
to as 'Heads of Test Laboratories' (HOTL).
Examination certificate
The Notified Body examines and tests the product to confirm it meets the standard
and issues an EC-type examination certificate to the manufacturer, entitling him to
display the CE mark on the product as proof of compliance.
Exd
See EExd.
Exi
See EExi.
Exia
See EExia.
Exib
See EExib.
ExNB
See Notified Bodies.
Workplaces which comprise areas where explosive atmospheres may form must be
verified prior to being put into operation. Sites must be verified by a person or
persons competent in explosion protection. Anyone claiming competence must be
able to produce evidence in the form of experience and/or professional training.
Explosive atmosphere
An explosive atmosphere can be one in the form of gases, vapours, mists or dusts,
which can ignite under certain operating conditions. Potentially explosive
atmospheres are found in many areas of industry, from mines and the chemical, oil
and gas, and pharmaceuticals industries, to plants handling cereal, animal feed,
paper, wood and coal. All these have the potential to produce gas, dust or fumes
which can be ignited by a spark or flame.
Explosive gas and dust is classified according to its likelihood to be ignited, according
to its characteristics: Minimum ignition energy; Minimum ignition temperature; Ignition
temperature; and Cloud & Layer ignition temperature for dusts.
F
Flameproof
The common name for protection type EExd. This is equipment of Category 2; used
in Zone 1 and Zone 2. The enclosure of this type of equipment will prevent an
internal explosion, or flame, from being transmitted to the explosive atmosphere
surrounding the machine, hence the name flameproof. No dangerous hot surface or
sparks may be present on the outside of the enclosure at rated operation. The
enclosure must withstand any pressure levels caused by such an internal explosion.
FM
Stands for Factory Mutual Research, a US based, non-profit scientific research and
testing organisation.
G
G-D
A product certified for both gas and dust is marked G-D. If the equipment is to be
installed in an environment that contains gas and dust, it needs to fulfil the
requirements for both.
Gas Group
See Apparatus Group.
Global ATEX system
The term 'Global ATEX system' refers to the three key elements necessary for ATEX
compliance: Harmonised standards, covering the EHSRs of ATEX Directive; Audits
at the manufacturing facility responsible for delivering the Ex-equipment, conducted
by an expert for quality Ex-system approved by the European Commission; and a
notification by the European Commission to recognise bodies and test laboratories
known as the Ex Notified Body Group (ExNBG).
Group
Under the ATEX Directive, equipment is designated by the type of potentially
explosive atmosphere in which the equipment may be used – Group 1 for
underground mines and Group 2 for surface industries. (See Apparatus Group)
H
Harmonised standard
Harmonised standards are listed in the Official Journal of the European Communities
to offer guidance to conformity with a particular Directive. See European Standards
Bodies and New approach directives.
Hazardous area
A location with an explosive atmosphere is referred to as a "Hazardous area" in IEC
countries and "HAZLOC" in North America.
HAZLOC
Explosive atmosphere is referred to as "Hazardous area" in IEC countries and
"HAZLOC" in North America.
I
IEC 60079-10: 2002-6
The standard for Area Classification of explosive gas atmospheres. This standard is
identical to EN 60079-10.
IEC 60079-17
IEC 60079-17 specifically covers the factors directly related to the inspection and
maintenance of electrical apparatus in hazardous areas other than mines.
The standard also sets out general requirements as to area classification, suitable
records and documentation, qualifications of personnel, initial and periodic
inspections, periods between inspections, grades of inspection (detailed, close or
visual) isolation of apparatus and appropriateness of apparatus to area classification
(BS EN 60079-14). Additional inspection requirements are also laid down for
particular types of protection ("d", "e", "i", "p" and apparatus used in zone 2).
IEC 60079-19
IEC 60079-19 sets down standards for the repair and overhaul for apparatus used in
explosive gas atmospheres (other than mines or explosives)
IEC
International Electrotechnical Commission. International standards for all electrical,
electronic and related technology are issued by IEC. It is made up of more than 60
participating countries, with the major goals being defining the requirements for
making the global market more efficient; improving efficiency in industrial processes;
improving health and safety; and protecting the environment. An IEC Ex-scheme is in
progress to harmonise the international testing and certification requirements for
hazardous applications.
IEEE
The IEEE (pronounced Eye-triple-E) is a non-profit, technical professional
association of more than 377,000 individual members in 150 countries. The full name
is the Institute of Electrical and Electronics Engineers, Inc. Based in the United
States; it is involved in technical publishing, conferences and consensus-based
standards activities.
Ignition
The relevant parameters to characterise the potentially explosive atmosphere are:
INERIS
European Notified Body, based in France.
Inspection
The IEC standard for inspection of electrical equipment in explosive gas
atmospheres is IEC 60079-17.
International standards
Equipment for explosive atmosphere is designed, installed, operated and maintained
according to international standards and local regulations dedicated to this area. See
IEC: International Electrotechnical Commission; EN: European Norm; and NEC:
National Electrical Code for North America
Intrinsically safe
Electrical equipment is said to be intrinsically safe where its circuits are designed to
limit the energy in any spark or thermal effect which can cause ignition in any of the
explosive atmospheres of subgroup IIA, IIB or IIC (see Apparatus Group).
Marking EExi in accordance with standard EN 50020 indicates that the equipment is
certified as intrinsically safe.
ISSeP
European Notified Body, based in Belgium.
J
July 1st 2003
1st of July 2003 is the implementation date for ATEX. Some aspects of ATEX have a
further transitional period of 3 years (i.e. up to June 30th 2006). As from July 1st 2003,
any equipment put on the market and intended to be used in a hazardous area in
Europe must be ATEX certified. This deadline includes protective systems,
components or devices that fall under the ATEX Directive.
Spare parts can be used and manufacturers can continue to manufacture spare parts
without the need to have them re-assessed under ATEX. The manufacturer may
supply a somewhat different version and if the function of the repaired product is not
materially changed then again ATEX does not apply.
Equipment which has already been placed on the market, including that in the supply
chain, may be used indefinitely providing the risk assessment under ATEX 137
permits it.
K
KEMA
European Notified Body, based in the Netherlands.
L
Layer ignition temperature
The risk of explosion in a hazardous area with combustible dust is either caused by a
layer of dust or a cloud of dust.
The ignition temperature of a 5mm layer of dust must be 75°C above the marking
temperature of the apparatus. For instance, if the ignition temperature is 200°C, the
marking temperature must be 125°C or lower. It is the responsibility of the user to
stage maintenance periods so that the dust layer does not build up above 5mm. The
ignition temperatures for various types of dust are available from commercially
available reference tables. Apparatus marked under American test regimes need
special consideration as the apparatus surface temperature is determined with a
12.5mm layer of dust on the apparatus – European testing is carried out dust-free.
The ignition temperature for a cloud of dust must be at least 50% above the
apparatus’ marking temperature; or, put differently, the marking temperature must not
exceed two-thirds of the ignition temperature of the dust. For instance, if the ignition
temperature of the dust is 210°C, the apparatus’ marking temperature must be lower
than 140°C.
LCIE
European Notified Body, based in France.
LEAC – List of Equipment for Area
Classification
A list (see IEC 60079-10: 2002-6 ) of sources of release used to determine and
record the zone type and extent.
Local regulations
Equipment for explosive atmospheres is designed, installed, operated and
maintained according to international standards and local regulations dedicated to
this area.
LOM
European Notified Body, based in Spain.
M
Maintenance
The IEC standard for maintenance of electrical equipment in explosive gas
atmospheres is IEC 60079-17.
Marking
Products that meet the requirements of the ATEX Directive are marked by the
manufacturer with the CE mark and the Ex mark. The following information is also
required: name and address of manufacturer; designation of series or type; serial
number, if any; and the year of manufacture. The CE mark should be followed by the
identity of the Notified Body involved at the quality surveillance, the EX symbol, the
equipment group, category and for equipment Group II, the letters G and/or D for
type of atmosphere (gases, vapours, mists and dusts).
National regulations
Each country has its own regulations, which may differ. National requirements might
be needed for final approval of installations e.g. in Russia, Brazil, Australia or Japan
but generally relate to one of the main international standards. See also Local
regulations.
NEC 500
In the U.S., the 'old' standard under the reference NEC 500 is still in existence;
defining the area according to the Division system. It will soon be replaced by the
new NEC 505 standard, similar to the IEC standard.
NEC
See National Electrical Code.
NEMA
National Electrical Manufacturers Association, the leading US trade association
representing the interests of electrical industry manufacturers. Sets standards
relating to electrically powered instrumentation equipment.
NEMKO (NO)
European Notified Body, based in Norway.
Non-electrical equipment
Non-electrical equipment is also covered by the ATEX directive. It covers any
equipment that may cause ignition of explosive atmospheres by hot surfaces, friction
sparks, electrostatic discharges or other means.
Non-hazardous area
An area in which an explosive gas atmosphere is not expected to be present in
quantities such as to require special precautions for the construction, installation and
use of apparatus. All types of standard products can be used. Hazardous area
equipment is, however, also frequently used in non-hazardous areas, for instance in
severe environments, corrosive atmospheres or anywhere else where reinforced
protection is required.
Non-sparking (EExn)
The lowest level of Ex protection for electrical apparatus is non-sparking, so called
because its design aims to prevent an internal malfunction from creating hot surfaces
or sparks in normal operation. This level of protection provides an economical
compromise between high safety requirements and normal industrial standards. They
are for use in Zone 2 only, i.e. for areas where explosive atmospheres occur
occasionally, but not during normal duty.
Norsok
Standard used in the oil and gas sector.
Notified Bodies
Approval of design and manufacture is issued by Notified Bodies. These are
independent testing laboratories recognised to perform tests, audit quality systems
and issue reports and certificates of conformity.
If a product is designed for use in Zone 0 and Zone 1 or Zone 20 and Zone 21, the
manufacturer must use a European Notified Body for testing and certification, usually
a company that specialises in testing industrial equipment.
The notified body examines and tests the product to confirm it meets the standard
and issues an EC-type examination certificate to the manufacturer, entitling him to
display the CE Mark on the product as proof of compliance. A new feature of the
ATEX Directive is that the manufacturer now also needs a quality system in place
that must be checked by a Notified Body which may or may not be the body carrying
out the EC-type examination.
To ensure that equipment is approved to the appropriate Directive, users need only
to check the directive number, which appears in the CE Declaration of Conformity
delivered with the product. Depending on the zone where the product is used, the
number of the notified body can be stamped after the CE mark (mandatory for use in
Zones 0, 1, 20 and Zone 21).
P
PFEER - Prevention of Fire & Explosion &
Emergency Response Regulations 1995
Legislation relating to offshore installations which covers the area excluded by
DSEAR. The regulations state that the person or company responsible for an
installation is also responsible for protecting persons on the installation from fire and
explosion and securing effective emergency response. Under the regulations,
operators are required to "identify and designate areas in which there is a risk of a
flammable or explosive atmosphere occurring" and control the "placing or use in such
areas of electrical fixtures or other sources of ignition".
PTB (DE)
European Notified Body, based in Germany.
PUWER
PUWER replaces the Provision and Use of Work Equipment Regulations 1992.
Under PUWER, employers are required to prevent or control risks to their employees’
health and safety posed by workplace equipment. This includes not only equipment
provided by the employer, but also any equipment brought into the workplace by the
employee which they use in the course of their employment.
The Regulations require that equipment provided by employers for use at work is:
Q
Quality assurance
Specific quality assurance is required for the design and the manufacturing process
relating to hazardous area equipment. See audit.
R
Recognized test organisations
See notified bodies.
Repair
When a piece of hazardous area equipment has to be repaired, the end user has the
responsibility to select an appropriate repair shop. See ATEX 137, Baseefa
Certification Limited
Risk Assessment
ATEX 137 requires the employer to assess the risks specifically arising from
explosive atmospheres. The risk assessment must cover the following:
The results of the risk assessment are used to guide the contents of the Explosion
Protection Document.
S
Self-certification
For equipment that will be used only in Zone 2 or Zone 22 environments and non-
electrical equipment (except combustion engines) that will be used in Zone 1 or Zone
21 environments where the requirements are less stringent, the ATEX Directive
allows manufacturers to self-certify products, although third-party certification is often
preferred.
Shell
Standard used by the oil and gas sector.
Sources of Hazard
The Employers’ obligations in relation to ATEX include assessing the site’s Sources
of Hazard and likelihood of sources of ignition, classification of the area into zones
and marking all points of entry, as well as producing and maintaining documentation.
See ATEX 137.
T
Temperature class
Temperature Temperature °C
class, gas
T1 450
T2 300
T3 200
T4 135
T5 100
T6 85
Test organisation
See Notified bodies.
Testing laboratories
See Notified bodies.
Transitional period
Although the ATEX directive was adopted in 1994, manufacturers and end users
have until now been able to choose whether to follow national or European
legislation. This transition period will end on June 30 2003, except for some specific
clauses in the Worker Protection Directive ATEX 137 and DSEAR.
TÜV
European Notified Body, based in Germany and Austria.
Type of Protection
There are a number of different methods of protection for which standards have been
or are being produced. These are as follows:
Electrical:
‘d’ – Flameproof
‘e’ – Increased Safety
‘i’ – Intrinsic Safety
‘m’ – Encapsulation
‘n’ – Zone 2 apparatus
‘o’ – Oil filled
‘p’ – pressurisation & continuous dilution
‘q’ – Sand filled
Non-electrical:
‘b’ – Control of ignition sources
‘c’ – Constructional safety
‘fr’ – Flow restricting enclosure
‘g’ – Inherent safety
‘k’ – Liquid immersion
plus ‘d’ and ‘p’
U
UL
Underwriters Laboratories Inc. (UL) is an independent, not-for-profit product safety
testing and certification organization, based in the United States.
V
VIK
Standard used by companies in the oil and gas sector.
VTT
European Notified Body, based in Finland.
W
Workers Potentially at Risk Directive
See ATEX 137.
Z
Zone
The ATEX 137 Directive divides hazardous environment into zones and states which
categories of equipment can be used in each zone.
Atmospheres are classified into zones. Zones 0, 1 and 2 refer to gas, while Zones
20, 21 and 22 refer to dust.
Zone 0
A place in which an explosive atmosphere consisting of a mixture of air and
flammable substances in the form of gas, vapour or mist is present continuously or
for long periods or on a frequent basis. A zone 0 application is typically one where an
explosive atmosphere exists for more than 1,000 hours per year.
Zone 1
A place in which an explosive atmosphere consisting of a mixture of air and
flammable substances in the form of gas, vapour or mist is likely to occur in normal
operation occasionally. In a zone 1 application, an explosive atmosphere typically
exists for between 10 and 1,000 hours per year.
Zone 2
A place in which an explosive atmosphere consisting of a mixture of air and
flammable substances in the form of gas, vapour or mist is not likely to occur in
normal operation but, if it does occur, will persist for a short period only. Explosive
atmospheres in a zone 2 application typically, do not exist for more than 10 hours
per year.
Zone 20
A place in which an explosive atmosphere in the form of a cloud of combustible dust
in air is present continuously, for long periods or on a frequent basis.
Zone 21
A place in which an explosive atmosphere in the form of a cloud of combustible dust
in air is likely to occur in normal operation occasionally.
Zone 22
A place in which an explosive atmosphere in the form of a cloud of combustible dust
in air is not likely to occur in normal operation but, if it does occur, will persist for a
short period only.
Zone drawings
The requirements for hazardous area classification, zoning and labelling will come
into force on July 1st 2003. Sites that were in existence prior to June 30th 2003 do
not need to comply until after 30th June 2006.
Zoning
The division of a hazardous area into zones depending on the frequency with which
an explosive atmosphere occurs and its duration. The overall aim is to ensure that
the employees and the public are protected from fires and explosion.
It involves identifying and assessing the fire and explosion risks of dangerous
substances within the operating plant. Properties of materials are to be agreed and
documented. Safety measures to eliminate or reduce the risks of these substances
are put in place.
Once no further improvements can be made to the operation, the plant can be put
forward for risk assessment and an area classification can be carried out.