Professional Documents
Culture Documents
Microhood Service Manual.
Microhood Service Manual.
정 판
MODEL 721.80032
721.80039
721.80033
DIVISION 22
MODEL 721.80032700
721.80039700
721.80033700
June, 2007
CAUTION
WARNING TO SERVICE TECHNICIANS
b. Make the following safety checks on all ovens to be serviced before activating the
magnetron or other microwave source, and make repairs as necessary; (1) Interlock
operation, (2) proper door closing, (3) seal and sealing surfaces (arcing, wear, and
other damage), (4) damage to or loosening of hinges and latches, (5) evidence of
dropping or abuse.
c. Before turning on microwave power for any service test or inspection within the
microwave generating compartments, check the magnetron, wave guide or
transmission line, and cavity for proper alignment, integrity, and connections.
d. Any defective or misadjusted components in the interlock, monitor, door seal, and
microwave generation and transmission systems shall be repaired, replaced, or
adjusted by procedures described in this manual before the oven is released to the
owner.
• Proper operation of the microwave ovens requires that the magnetron be assembled to the
wave guide and cavity. Never operate the magnetron unless it is properly installed.
• Be sure that the magnetron gasket is properly installed around the dome of the tube whenever
installing the magnetron.
• Untrained personnel should not attempt service without a thorough review of the test
procedures and safety information contained in this manual.
FOREWORD
Read this Manual carefully. Failure to adhere to or observe the information in this Manual may result in exposing
yourself to the Microwave Energy normally contained within the oven cavity.
TABLE OF CONTENTS
(Page)
SAFETY PRECAUTIONS ................................................................................................................Inside front page
SPECIFICATIONS ................................................................................................................................................ 1-1
CAUTIONS ........................................................................................................................................................... 2-1
INSTALLATIONS .................................................................................................................................................. 3-1
OPERATING INSTRUCTIONS............................................................................................................................. 4-1
CONTROL PANEL .......................................................................................................................................... 4-1
CONTROL PANEL INSTRUCTIONS............................................................................................................... 4-2
OVERALL CIRCUIT DIAGRAM ............................................................................................................................ 5-1
SCHEMATIC DIAGRAM .................................................................................................................................. 5-1
MATRIX CIRCUIT FOR TOUCH KEY BOARD ............................................................................................... 5-2
GENERAL INFORMATION FOR SERVICE ......................................................................................................... 6-1
GENERAL PRECAUTIONS IN USE ............................................................................................................... 6-1
TRIAL OPERATION ........................................................................................................................................ 6-1
FEATURES AND SPECIFICATIONS FEATURES .......................................................................................... 6-1
SERVICE INFORMATION .................................................................................................................................... 7-1
PRECAUTIONS AND REPAIR SERVICE TIPS .............................................................................................. 7-1
MICROWAVE LEAKAGE TEST ...................................................................................................................... 7-2
POWER OUTPUT MEASUREMENT............................................................................................................... 7-3
DISASSEMBLY INSTRUCTIONS ................................................................................................................... 7-4
INTERLOCK SYSTEM .................................................................................................................................. 7-11
INTERLOCK CONTINUITY TEST ................................................................................................................. 7-13
TEST AND CHECKOUT PROCEDURES AND TROUBLESHOOTING........................................................ 7-14
A. TEST PROCEDURES ........................................................................................................................... 7-14
B. CHECKOUT PROCEDURES ................................................................................................................ 7-19
C. TROUBLESHOOTING .......................................................................................................................... 7-21
EXPLODED VIEW ................................................................................................................................................ 8-1
REPLACEMENT PART LIST................................................................................................................................ 9-1
SPECIFICATIONS
Rated Power Consumption ................................ 1500W maximum (Microwave oven+Cook top lamps+Ventilation fan)
Microwave Output ............................................... 1000W (IEC60705)
Frequency .......................................................... 2450 MHz ±50 MHz
Power Supply ..................................................... 120 VAC, 60 Hz
Rated Current .................................................... 14 Amp. (Microwave oven+Cook top lamps+Ventilation fan)
Magnetron Cooling ............................................. Forced Air Cooling
Rectification ....................................................... Rectification Voltage Double Half-Wave
Door Sealing ...................................................... Choke System
Safety Devices ................................................... Oven Thermostat: Open at 90 °C ± 5 °C
Close at 0 °C ± 5 °C
............................................................................ Fuse(20A)
............................................................................ Primary Interlock Switch
............................................................................ Secondary Interlock Switch
............................................................................ Interlock Monitor Switch
Magnetron .......................................................... 2M214 - 161GP
Cook top Lamp ................................................... 125 V, 30 W
Cavity Lamp ....................................................... 125 V, 30 W or 40 W
Timer .................................................................. Digital, up to 99 min. 99 sec. (in each cooking stage)
Tray .................................................................... Tempered Safety Glass
Overall Dimensions ............................................ 2915/16”(W)x167/16”(H)x1511/16”(D)
Oven Cavity Size ............................................... 219/16”(W)x91/4”(H)x141/8”(D)
Effective Capacity of Oven Cavity ...................... 1.6 Cu.ft.
Accessories ........................................................ Owner’s Manual & Cooking Guide, Installation Manual,
............................................................................ Exhaust Adapter, Exhaust Damper, Mounting Kit and Filter,
............................................................................ Glass Tray, Rotating Ring Assembly.
SWITCH CHART
PRIMARY SECONDARY INTERLOCK
SWITCH MODE INTERLOCK INTERLOCK MONITOR
SWITCH SWITCH SWITCH
COM COM COM
CONDITIONS
NO NO NC
DOOR OPEN OPEN OPEN CLOSE
DOOR CLOSED CLOSE CLOSE OPEN
NOTE: Use the above switch chart with circuit diagram on page 5-1.
1-1
CAUTIONS
Unlike other appliances, the microwave oven is
MICROWAVE RADIATION
high-voltage and high-current equipment.
Personnel should not be exposed to the
Though it is free from danger in ordinary use,
microwave energy which may radiate from the
extreme care should be taken during repair.
magnetron or other microwave generating
device if it is improperly used or connection.
• DO NOT operate on a 2-wire extension cord during repair All input and output microwave connections,
and use. waveguide, flange, and gasket must be secure
• NEVER TOUCH any oven components or wiring during never operate the device without a microwave
operation. energy absorbing load attached.
• BEFORE TOUCHING any parts of the oven, always Never look into an open waveguide or antenna
remove the power plug from the outlet. while the device is energized.
• Remove your watches whenever working close to or
replacing the Magnetron.
• DO NOT touch any parts of the control panel circuit. A • Proper operation of the microwave oven requires that
resulting static electric discharge may damage this P.C.B. the magnetron be assembled to the waveguide and
• NEVER operate the oven with no load. cavity. Never operate the magnetron unless it is
• NEVER injure the door seal and front plate of the oven properly installed.
cavity. • Be sure that the magnetron gasket is properly
• NEVER put iron tools on the magnetron. installed around the dome of the tube whenever
• NEVER put anything into the latch hole and the interlock installing the magnetron.
switches area.
ANTENNA
Gasket
COOLING FIN
MAGNETRON
CHASSIS GROUND FILAMENT
TERMINALS
MAGNETRON
2-1
INSTALLATIONS
BEFORE YOU BEGIN, READ THE FOLLOWING INSTRUCTIONS COMPLETELY AND CAREFULLY.
PRECAUTIONS ON INSTALLATION
A. Plug the power supply cord into a 120V AC, 60Hz,
single-phase power source with a capacity of at
least 20 amperes.
B. Avoid placing the unit in a location where there is
direct heat or splashing water.
C. Install the unit on the mounting plate firmly.
D. Place the unit as far away as possible from TV,
radio, etc. to prevent interference.
GROUNDING INSTRUCTIONS
For personal safety, this appliance must be fully
grounded at all times.
In the event of an electrical short circuit, grounding
reduces the risk of electrical shock.
The plug must be plugged into an outlet that is
properly installed and grounded.
CAUTION
This unit is equipped with a 3-prong plug for your
safety. If the wall outlet is a grounded 3-hole type,
the unit will be grounded automatically.
WARNING
Improper use of the grounding plug can result in a
risk of electric shock.
Do not, under any circumstances, cut or remove the
third ground prong from the power cord plug.
3-1
OPERATING INSTRUCTIONS
CONTROL PANEL
2 4
5 8
6 11
9 12
10
14
15
13
16
17
18
19 20
20
23
22
4-1
CONTROL PANEL INSTRUCTIONS
1. Display: The display includes a clock and 13. Number Pads: Touch number pads to enter
indicators to tell you time of day, cooking time cooking times, cook powers, quantities,
settings, cook powers, quantities, weights and weights, or food categories.
cooking functions selected.
14. CLOCK: Touch this pad to enter the correct
2. POPCORN: Touch this pad to pop one of 2 bag time of day.
sizes of popcorn without entering a cook time or
15. ADD MINUTE: Touch this pad to cook for 1
power.
minute at 100%cook power,or to add extra
3. PIZZA: Touch this pad to reheat one or several minutes at the set cook power to your cooking
slices of pizza without entering a cook time or cycle.
power.
16. HOLD WARM: Touch this pad to keep hot,
4. POTATO: Touch this pad to cook up to 4 cooked foods warm in your microwave oven for
potatoes without entering a cook time or power. up to 99 minutes 99 seconds.
5. FROZEN ENTREE: Touch this pad to cook a 10 -to 17. TURNTABLE ON/OFF: Touch this pad to turn off
20 -ounce (284 to 567 g)frozen entree without the turntable.“OFF ” will appear in the display.
entering a cook time or power.
18. COOK TIME: Touch this pad followed by
6. AUTO COOK: Touch this pad to cook Number Pads to set a cooking time.
microwavable foods without entering a cook
19. POWER: Touch this pad after the cook time
time or power.
has been set, followed by a Number Pad to set
7. DINNER PLATE: Touch this pad to cook without the amount of microwave energy released to
entering a cook time or power. cook the food. The higher the number, the
higher the microwave power or “cooking speed.”
8. AUTO DEFROST: Touch this pad followed by
number pads to thaw frozen meat by weight. 20. START: Touch this pad to start a function.
If you open the door after the oven begins to
9. AUTO REHEAT: Touch this pad to reheat
cook, retouch START.
microwavable foods without entering a cook
time or power. 21. Fan ( ) Hi/Low/Off: Touch this pad to
turn the fan on high, low or off.
10. SOFTEN: Touch this pad to soften butter, ice
cream, cream cheese, frozen juice. 22. Light ( ): Touch this pad to turn the light on
high, night (low) or off.
11. MELT: Touch this pad to melt butter or
margarine, chocolate, cheese, or 23. STOP: Touch this pad to erase an
marshmallows. incorrect command,cancel a program during
cooking,or to clear the Display.
12. TIMER: Touch this pad to set the kitchen timer.
NOTE: If you try to enter incorrect instructions,
you will not hear any tones. Touch STOP/Clear
and re-enter the instructions.
off the turntable.“OFF ” will appear in the
display.
4-2
OVERALL CIRCUIT DIAGRAM
SCHEMATIC DIAGRAM
5-1
MATRIX CIRCUIT FOR TOUCH KEY BOARD
KEY MATRIX
5-2
GENERAL INFORMATION FOR SERVICE
GENERAL PRECAUTIONS IN USE FEATURES AND SPECIFICATIONS
A. Never operate the unit when it is empty. FEATURES
Operating the oven with no load may shorten the A. The safety systems incorporated in this model are:
life of the magnetron. Whenever cooking dry foods (1) Primary interlock switch
(dried fish, bread, etc.)or a small amount of food, (2) Secondary interlock switch
be sure to put a glass of water into the cooking (3) Interlock monitor switch
compartment. The glass turntable may become hot (4) Choke system
after operating, be careful when touching it. (5) Oven cavity thermostat
B. Aluminum foil should be avoided because it will (Note This thermostat located on the oven cavity
disrupt cooking and may cause arcing. However, will open and stop the unit from operation only if
small pieces may be used to cover some parts of a high temperature is reached, such as, a fire
food to slow the cooking. Any aluminum foil used created by overcooking food.)
should never be closer than 2.5 cm to any side wall B. Any one of 10 power output levels ranging 0W to
of the oven. 1000W can be selected by the touch control and
electronic computer system.
TRIAL OPERATION C. Cooking time can be displayed on the digital
readout.
After installation, the following sequences and results
D. Three different cooking stages (Include Defrost)
should be checked carefully.
can be changes from one cooking stage to another.
This is made possible with the memory function of
A. Put a container filled with water (about 1 liter)into
the microprocessor.
the oven, and close the door tightly.
B. Set cooking time for 10 minutes by touching “1 ”
and then “0” three times.“1, 0, 0, 0” appears in the
display window.
C. Touch the START key.
Make sure the cavity light comes on. The unit will
begin cooking and the display window will show the
time counting down by seconds.
D. After about 5 minutes, make sure the primary
interlock switch, the secondary interlock switch and
the interlock monitor switch operate properly by
opening and closing the door several times. Touch
the START key each time the door is closed.
E. Continue operating the unit. Two short and a long
beep sound signal is heard when the time is up.
The unit will shut off automatically.
F. Confirm the water is hot.
G. Finally, measure the output power according to
“POWER OUTPUT MEASUREMENT” on
page 7-3.
6-1
SERVICE INFORMATION
PRECAUTIONS AND REPAIR SERVICE TIPS
PRELIMINARY (3) Do not operate the unit until it is completely
repaired, if any of the following conditions exist.
The unit must not be operated.
A. SINCE NEARLY 4000 VOLTS EXISTS IN SOME (a) The door does not close firmly.
CIRCUITS OF THIS UNIT REPAIRS SHOULD BE (b) The hinge is broken.
CARRIED OUT WITH GREAT CARE. (c) The door seal is damaged.
The filament leads of magnetron carry High (d) The door is bent or warped, or there is any
Voltage with respect to ground. Extreme caution other visible damage on the unit that may
must be exercised. Never plug the unit into a cause microwave energy leakage.
power source to determine which component is NOTE: Always keep the seal clean.
defective in high voltage section. (e) Make sure that there are no defective parts
in the interlock mechanism.
B. TO AVOID POSSIBLE EXPOSURE TO (f) Make sure that there are no detective parts
MICROWAVE ENERGY LEAKAGE, THE in the microwave generating and transmission
FOLLOWING PRECAUTIONS MUST BE TAKEN assembly (especially waveguide).
BEFORE SERVICING.
(1) Before the power is applied: (4) The following items should be checked after the
(a) Make sure the primary interlock switch, the unit is repaired:
secondary interlock switch and the interlock (a) The interlock monitor switch is connected
monitor switch operate properly by opening correctly and firmly.
and closing the door several by opening and (b) The magnetron gasket is properly positioned
closing the door several times. and mounted.
(b) Make sure the perforated screen and the (c) The waveguide and the oven cavity are intact.
dielectric choke of the door are correctly and (no microwave energy leakage)
firmly mounted. (d) The door can be properly closed and the
safety switches work properly.
(e) The unit must stop when the door is opened or
(2) After power is applied:
the time is up.
(a) Make sure the interlock switch mechanism
is operating properly by opening and closing
the door. The unit must not be operated with any of the above
components removed or by-passed.
(b) Check microwave energy leakage must be below
the limit of 5 mW/cm2 .
(All service adjustments should be made for
minimum microwave energy leakage
readings).
7-1
MICROWAVE LEAKAGE TEST
CAUTIONS EQUIPMENT-
7-2
MEASUREMENT WITH THE OUTER CASE NOTE WHEN MEASURING
REMOVED (1) Do not exceed meter full scale deflection.
(1) When you replace the magnetron, measure for (2) The test probe must be removed no faster than
microwave energy leakage before the outer case 1 inch/sec (2.5cm/sec)along the shaded area,
is installed and after all necessary components otherwise a false reading may result.
are replaced or adjusted. Special care should be (3) The test probe must be held with the grip portion
taken in measuring the following parts. of the handle. A false reading may result if the
-Around the magnetron operator ’s hand is between the handle and the
-The waveguide probe.
(4) When testing near a corner of the door, keep
WARNING: AVOID CONTACTING ANY HIGH the probe perpendicular to the surface making
VOLTAGE PARTS. sure the probe horizontally along the oven
surface, this may possibly cause probe damage.
Figure 2
(5) Remove the FPC connector from the terminal
socket following “HOW TO REMOVE THE FPC
CONNECTOR” on the next page.
(6) Remove the circuit board from the control bracket
carefully.
Figure 1
7-4 Figure 3
HOW TO REMOVE THE F.P.C. CONNECTOR HOW TO INSERT THE F.P.C. CONNECTOR
Follow the steps below as illustrated in Figures 4 Follow the steps below as illustrated in Figures 6
and 5 to remove the F.P.C. connector. and 7 to insert the F.P.C. connector.
(1) Insert the F.P.C. connector into the terminal
(1) Hold the edges of the plastic fastener with socket securely with the fingers.
thumb and forefinger. (2) Hold the plastic fastener with thumb and
(Figure 4) forefinger of the other hand, and push it
(2) Lift up the lever of the plastic fastener from slowly into the terminal socket. (Figure 6)
the terminal socket by lightly pressing the NOTE: When reconnecting the F.P.C.
lever end with forefinger. connector make sure that the holes
(Figure 5) on the F.P.C. connector are properly
(3) Remove the F.P.C. connector from the engaged with the hooks on the plastic
terminal socket. fastener
(3) Lock the level of the plastic fastener into the
hook of the terminal socket securely by
releasing the fingers.
(Figure 7)
Figure 4
Figure 6
Figure 5
Figure 7
7-5
B. REMOVING THE OUT CASE(Figure 8)
(1) Remove the vent grille by removing two screws
securing it to the out case.
(2) Remove two screws securing it to the air duct.
(3) Remove the mounting plate by turning the screws
(1 or 2 screws)securing it to the out case.
(4) Remove two screws on the left central edge and
one screw on the right central edge of Base plate.
Remove the Mount, All from the out case by
removing one screw securing it to the out case.
(5) Remove six screws of the rear cavity.
(6) Remove the outcase.
Mount,All
Power code
Door
Mounting
Plate
Out Case
Figure 8
7-6
C. REMOVING THE DOOR INTERLOCK
SWITCHES (Figures 9, 10)
(1) Disconnect the wire leads from the interlock
switches.
(2) Remove two screws securing the Latch Board.
(3) Make necessary replacements and check
microwave energy leakage according to
“ADJUSTMENT PROCEDURES” on page 7-12.
Figure 10
Figure 9
7-7
D. REMOVING MAGNETRON NOTES:
(Figures 11 Through 12) • When removing the magnetron, make sure that its
(1) Remove the vent grille by loosening two screws. dome does not hit any adjacent parts, or it may be
(Figure 11) damaged.
(2) Remove the outcase. See page 7-6.
(3) Remove four tap tite screws securing the • When replacing the magnetron, be sure to install the
magnetron to the wave guide. magnetron gasket in the correct position and be sure
(4) Disconnect the leadwire. that the gasket is in good condition.
(5) Remove the magnetron VERY CAREFULLY.
• After replacing the magnetron, check for microwave
energy leakage with a survey meter Check
microwave energy leakage must be below the limit
of 5 mW/cm2. (All service adjustments should be
made for minimum microwave energy leakage
readings.)
mount all
vertgrille
Figure 11
Magnetron
Figure 12
7-8
E. DOOR ASSEMBLY / REMOVAL F. ASSEMBLING DOOR
1) Open the door. (1) When mounting the door assembly to the oven
2) Remove the choke cover very carefully with a flat- assembly, be sure to adjust the door assembly
blade screwdriver. parallel to the chassis. Also adjust so the door has no
CAUTION : Be careful not to damage door seal plate play between the inner door surface and oven frame
by screwdriver. assemblyIf the door assembly is not mounted
3) Lift up and push the door. properly, microwaves may leak from the clearance
between the door and the oven.
Remove door assembly
Figure 13
Figure 14-a
7-9
(3) Carefully pull the ventilation motor ASS'Y out ofthe H. REMOVING THE TURNTABLE MOTOR
microwave oven. (See Figure 14-b) (1) Remove the glass tray and rotating ring.
(2) Remove the turntable shaft VERY CAREFULLY
with a hand. (Figure 15)
(3) Remove the base plate by removing 8 screws
securing it to the oven cavity. (Figure 16)
(4) Disconnect the leadwire from the turntable motor
terminals.
(5) Remove the 1 screws securing the turntable motorto
the oven cavity ASS'Y. (Figure 17)
NOTES:
Figure 14-b • Remove the leadwire from the turntable motor
VERY CAREFULLY.
• Be sure to grasp the connector not the wires when
removing.
Figure 15
Figure 16
Figure 17
7-10
INTERLOCK SYSTEM
INTERLOCK MECHANISM
The door lock mechanism is a device which has been specially designed to eliminate completely microwave
activity when the door is opened during cooking and thus to prevent the danger resulting from the microwave
leakage.
NOTE:
To correct sequence of the Primary Interlock
Switch, Secondary Interlock Switch and the
Interlock Monitor Switch is very important.
If any gap is larger than 1/64” (0.5 mm), you will
need to adjust the latch board”. Go to step 3
and follow all steps in order.
(4) With the oven door closed tightly, move the latch
board upward toward the top of the oven and/or
away from the door latch until the gaps are less
than 1/64 ” (0.5 mm).
Figure 23-a Hold the latch board tightly in this position until you
check the sequence of the switches in steps 5
and 6.
Figure 23-b
7-11
TEST THE LATCH AND SWITCH SEQUENCE (7) When you achieve the proper sequence of
switches in Steps 5 and 6, tighten the latch board
(5) Open the oven door slowly. Watch the door latch, screws at that point.
the Secondary Switch. Release Rod and Lever
on the switches to make sure they are zero to the TEST THE MICROWAVE ENERGY LEAKAGE
body of the switches in the following sequence:
Make sure the microwave energy leakage is below the
-Primary Interlock Switch limit of 1mW/cm2 (with a 275 ml water load) and
-Secondary Interlock Switch 5mW/cm2 (with a 275 ml water load without the
-Interlock Monitor Switch cabinet) when measured with a survey meter.
7-12
INTERLOCK CONTINUITY TEST
A. PRIMARY INTERLOCK SWITCH TEST B. SECONDARY INTERLOCK SWITCH TEST
When the door is opened slowly, an audible click Disconnect the wire lead from the secondary
should be heard at the same time or successively switch.
at intervals and the latches should activate the Connect the ohmmeter leads to the common
switches with an audible click (COM)and normally open (NO)terminals of the
If the latches do not activate the switches when the switch. The meter should indicate a open circuit in
door is closed, the switches should be a adjusted the door open condition. When the door is closed,
in accordance with the adjustment procedure. meter should indicate an closed circuit. When the
Disconnect the wire lead from the primary switch. secondary switch operation is abnormal, make the
Connect the ohmmeter leads to the common necessary adjustment or replace the switch only
(COM)and normally open (NO)terminal of the with the same type of switch.
switch. The meter should indicate an open circuit
in the door open condition. C. MONITOR SWITCH TEST
When the door is closed, the meter should indicate Disconnect the wire lead from the monitor switch.
a closed circuit. Connect the ohmmeter leads to the common
When the primary switch operation is abnormal, (COM)and normally closed (NC)terminals of the
make the necessary adjustment or replace the switch. The meter should indicate closed circuit in
switch only with the same type of switch. the door open condition. When the door is closed,
meter should indicate an open circuit. When the
monitor switch operation is abnormal, replace with
the same type of switch.
NOTE: After repairing the door or the interlock
system, it is necessary to do this continuity
test before operating the oven.
Primary NO
COM
Switch
NC
Monitor
COM
Switch
Secondary
NO
Switch COM
NOTE : After checking for the continuity of switches, make sure that they are
connected correctly.
7-13
TEST AND CHECKOUT PRECEDURES AND TROUBLESHOOTING
CAUTIONS
1. DISCONNECT THE POWER SUPPLY CORD FROM THE OUTLET WHENEVER REMOVING THE OUTER CASE
FROM THE UNIT. PROCEED WITH THE TEST ONLY AFTER DISCHARGING THE HIGH VOLTAGE CAPACITOR
AND REMOVING THE LEAD WIRES FROM THE PRIMARY WINDING OF THE HIGH VOLTAGE TRANSFORMER.
2. ALL OPERATIONAL CHECKS WITH MICROWAVE ENERGY MUST BE DONE WITH A LOAD (1 LITER OF
WATER IN CONTAINER)IN THE OVEN.
A. TEST PROCEDURES
TRANSFORMER
FILAMENT SECONDARY
WINDING WINDING
PRIMARY
WINDING
MAGNETRON
Antenna
Gasket
Chassis
Filament
7-14
COMPONENTS TEST RESULTS
Abnormal :
Approximately 0V
• Terminal to case
Normal:
Approximately 0V or
a value displayed in
mV Will be seen.
Normal:
Abnormal:infinite
N(1)-N(2)(coil):Less than 1 ohm
L(1)-L(2)(coil):Less than 1 ohm
Abnormal: 0 ohms
1.5M ohms
Abnormal:
Infinite or several.
7-16
COMPONENTS TEST RESULTS
CONNECTOR(KEY CON)
NOTES:
• A MICROWAVE ENERGY TEST MUST ALWAYS BE PERFORMED WHEN THE UNIT IS SERVICED FOR
ANY REASON.
• MAKE SURE THE WIRE LEADS ARE IN THE CORRECT POSITION.
• WHEN REMOVING THE WIRE LEADS FROM THE PARTS, BE SURE TO GRASP THE CONNECTOR, NOT
THE WIRES.
7-17
B. CHECKOUT PROCEDURES
(1) CHECKOUT PROCEDURES FOR FUSE BLOWING
Fuse blows when the door is closed and START Malfunction of the high voltage transformer; the high
key is touched. voltage capacitor including the diode, the magnetron,
the blower motor or the circuit board.
NOTES:
• If the fuse is blown by an improper switch operation, replace all switches and the fuse at the same time.
After replacing the defective switches with new ones, make sure that they are correctly connected.
• Check for microwave energy leakage according to INTERLOCK ADJUSTMENT PROCEDURES on page
7-12 when the primary interlock, secondary interlock switches and/or the interlock monitor switches are
adjusted or replaced.
7-18
(2)CHECKOUT PROCEDURES FOR RELAY.
NO YES NO YES
Remove the mate connector of I/O Remove the mate connector of I/O
GOOD GOOD
CON from the circuit board. CON from the circuit board.
Does the unit still operate? Does the unit still operate?
NO YES NO YES
Replace Replace
Wire Assembly Wire Assembly
YES NO YES NO
Measure the voltage at pin NO. Measure the voltage at pin NO.
GOOD GOOD
1,4 of CN1 1,4 of CN1
Voltage reading:120 V AC Voltage reading:120 V AC
NO YES NO YES
Replace Replace
FAN motor. Oven lamp
7-19
(3) CHECKOUT PROCEDURES FOR CIRCUIT
BOARD
The following symptoms indicate a defective circuit 6) Wrong figures appear.
board. 7) The figures of all digits.
1) The start function fails to operate but the high 8) Some of the indicators do no flicker light up.
voltage Systems, the interlock switches, the door 9) The clock does not keep time properly.
sensing and the relay check good.
2) The unit with a normal relay continuously operates.
3) Proper temperature measurement is not obtained.
4) The buzzer does not sound or continues to sound.
5) Some segments of one or more digits do not light
up, or they continue to light up, or segments light
when they should not.
NOTE: A MICROWAVE ENERGY LEAKAGE TEST MUST ALWAYS BE PERFORMED WHEN THE UNIT IS
SERVICED FOR ANY REASON.
7-20
C. TROUBLE SHOOTING
Before following this troubleshooting read “TRIAL OPERATION” on page 6- 1.
• “DISPLAY” Problems, “A” thru “C”
• “HELP UP” Problems, “D” thru “E” • “BUZZER Problems, “F”
PROBLEM - A: “PLEASE SET TIME OF DAY” does not appear in display window when power supply cord is
plugged into wall outlet.
7-21
PROBLEM - B: Display does not show correct numbers and/ or
correct indications when programmed.
1
PROBLEM - E: Unit does not heat up even if display counts down when
START key is touched for “HIGH POWER” cooking.
7-22
PROBLEM - F: No buzzing when touching the key, between
stages or at end of cooking
7-23
PROBLEM - Ventilation fan does not operate when “ON/OFF” key is touched.
7-24
#EV#
EXPLODED VIEW
DOOR PARTS
FOR MODEL :
1004
1005
1002
1000
1008 W109
1003
1006
W109
1007
1009
FOR MODEl :
1004
1005
1002
1000
1008 W109
1381
1006
W109
1007
1009
-8-1-
#EV#
CONTROLLER PARTS
FOR MODEL :
2006
2004
2381
2008
W106
2018
W101
MBM2
2000
2002
FOR MODEl :
2006
2004
2381
2008
W106
2018
W101
MBM2
-8-2-
#EV#
W108
3010
W109
For Model
W142
For Model
W138
3024
W142
3029 W138
3001
3003
W105
5038
5036
6001
6000
3028
3011
3026
3025
W118
3026 W118
-8-3-
#EV#
4000
4001
4002
W102
4003
4002
4004
-8-4-
#EV#
3002 W101
5039
3012
5009
W101
W109
3008
W109
W108
5008
3034
5035
3037
W108
5002
5000
5034
-8-5-
#EV#
5015
5037
5045 5001
W130
W108
5038
5041
W109
5016
W101
5014
5024
5058
5043
5044
3004
-8-6-
#EV#
INSTALLATION PARTS
6008
6011
6010
6009
VINYL
BAG
COOKING
OWNERS MFL1 INSTALLATION MFL3 GUIDE
MEZ1 UPPER MBM4 WALL MBM5
MANUAL MANUAL TEMPLATE TEMPLATE
LABEL
-8-7-
Part Reference list (1.6 Cuft)
For Model : 721.80032 Rev.1 Jun 18, 2007
Location 721.80032700 Part Name SVC Alternate
No. PART NO
*01 MFL39431001 Manual,Owners R
*02 MFL30502903 Manual,Service R
*04 MFL39433001 Manual,Installation R
*05 MEZ40037401 Label,Cooking Guide R
*06-1 4922W1A021E Card,Template R
*06-2 4922W5A058A Card,Template R
*07 MBM00607003 Card,Technical R
*10 3890W3Y925M Box R
1000 3213W1A049G Frame Assembly,Door R
1002 3536W1A012B Tape,Sealing R
1003 MGC38915901 Panel,Door R
1004 3552W1A032E Cover,Choke R
1005 ADC33688801 Door Assembly R
1006 4026W2A019C Locker R 4026W2A019A
1007 4970WRA001G Spring R
1008 MKC39429001 Window,Glass R
1009 MEB38925701 Handle,Door R
2000 MFM39438701 Membrane R
2002 MGC38916001 Panel,Control R
2004 ACM33689601 Controller Assembly,Keypad R
2006 6871W1A497C PCB Assembly,Sub R
2008 MAZ38922001 Bracket,Control Panel R
2018 0CZZW1M001C Capacitor,Film,Box R
2381 AGM34653701 Parts Assembly(Control Panel+Key Pad) R
3001 3112W1F056T Case,Flat R
3002 1B71961H Tray,Glass R
3003 ABU33693602 Cavity Assembly,Coating R
3004 4051W3A001A Connector Assembly R
3008 5889W2A012F Turntable Assembly R
3009 6549W1S013K Motor, AC Synchronous R
3010 4960W1A022A Plate R
3011 4890W1A045A Window,Glass R 4890W4A001G
3012 4370W1A011A Shaft,Turntable R
3024 MDX38927301 Grille,Vent R
3025 4810W1A150C Bracket,Lamp R
3026 5230W1A012C Filter,Grease R 2B72705B
3026 5230W1A012C Filter,Grease R 5230W1A012A
3026 5230W1A012C Filter,Grease R 5230W1A012B
3027 6549W1V006W Motor, AC Ventilation R
3028 6912W1Z004B Lamp,Incandescent R 6912W1Z002B
3029 4810W1A149A Bracket,Mount R
3034 3052W1A002A Cover,Resin R
3037 MJH38925501 Supporter R
4000 3500W1A028B Holder,Locker R
4001 3501W1A019D Holder Assembly,Locker R
4002 6600W1K001D Switch,Micro R
4003 6600W1K001C Switch,Micro R
4004 4510W3A012C Lever R
5000 0CZZW1H004B Capacitor,High Voltage R 0CZZW1H004G
5000 0CZZW1H004B Capacitor,High Voltage R 0CZZW1H002H
5000 0CZZW1H004B Capacitor,High Voltage R 0CZZW1H001Q
5001 3B74133Q Fuse,Time Delay R 3B74133K
5002 4810W1A141A Bracket,Capacitor R
9-1
Location 721.80032700 Part Name SVC Alternate
No. PART NO
5006 5208W0A006C Duct R
5008 6170W1D052R Transformer,high voltage R 6170W1D052U
5009 2B71165R Magnetron R
5010 6411W1A019M Power Cord Assembly R
5014 6877W1A597V Harness,Single R
5015 6912W1Z004A Lamp,Incandescent R
5016 6930W1A003E Thermostat R 6930W3A001S
5016 6930W1A003E Thermostat R EBG33435103
5018 6851W1A002B Cable,Assembly R 6021W3B001G
5018 6851W1A002B Cable,Assembly R 6021W3B001S
5024 5893W3A002D Fan Assembly R 5893W3A002C
5034 3300W1A046C Plate,Bottom R
5035 3300W1A052B Plate,Bottom R
5036 3550W3A095C Cover,Lamp R
5037 5230W1A011C Filter,Charcoal R 2B72706D
5037 5230W1A011C Filter,Charcoal R 5230W1A011A
5037 5230W1A011C Filter,Charcoal R 5230W1A011B
5038 6620G00007A Lamp Holder R
5039 MAZ37440501 Bracket R
5041 EAM35001801 Filter,AC Line R 2B72130F
5043 4930W1A068A Holder,Stirrer Fan R
5044 3550W1A126B Cover,Stirrer Fan R 3550W1A126A
5045 3550W1A189A Cover,Lamp R
5058 5892W1A003A Fan R
5067 4810W1A305B Bracket,Thermostat R
5337 3740W1A011B Supporter R
6000 3302W0A047M Plate,Base R
6001 3303W1A072N Plate Assembly,Base R
6008 3300W0A030A Plate,Mount R
6009 3861W1A043C Kit Assembly R
6010 4810W1A151A Bracket,Idle R
6011 4900W1A001B Damper R
W101 1SBF0402418 Screw,Taptite R
W102 4B70188C Screw,Customized R
W105 1TPL0402418 Screw,Tapping R
W106 1TPL0402818 Screw,Tapping R
W108 1TTL0402418 Screw,Tapping R
W109 1TTL0402818 Screw,Tapping R
W118 1TTG0402422 Screw,Tapping R
W130 1TPL0402618 Screw,Tapping R
W138 1TTL0402822 Screw,Tapping R
9-2
Part Reference list (1.6 Cuft)
For Model : 721.80039 Rev.1 Jun 18, 2007
Location 721.80039700 Part Name SVC Alternate
No. PART NO
*01 MFL39431001 Manual,Owners R
*02 MFL30502903 Manual,Service R
*04 MFL39433001 Manual,Installation R
*05 MEZ40037401 Label,Cooking Guide R
*06-1 4922W1A021E Card,Template R
*06-2 4922W5A058A Card,Template R
*07 MBM00607003 Card,Technical R
*10 3890W3Y925N Box R
1000 3213W1A049F Frame Assembly,Door R 3213W1A049J
1002 3536W1A012B Tape,Sealing R
1003 MGC38915902 Panel,Door R
1004 3552W1A032E Cover,Choke R 3552W1A063A
1005 ADC33688802 Door Assembly R
1006 4026W2A019A Locker R
1007 4970WRA001G Spring R
1008 MKC39429002 Window,Glass R
1009 MEB38925702 Handle,Door R
2000 MFM39438702 Membrane R
2002 MGC38916002 Panel,Control R
2004 ACM33689602 Controller Assembly,Keypad R
2006 6871W1A497C PCB Assembly,Sub R
2008 MAZ38922001 Bracket,Control Panel R
2018 0CZZW1M001C Capacitor,Film,Box R
2381 AGM34653702 Parts Assembly(Control Panel+Key Pad) R
3001 3112W1F056S Case,Flat R
3002 1B71961H Tray,Glass R
3003 ABU33693602 Cavity Assembly,Coating R
3004 4051W3A001A Connector Assembly R
3008 5889W2A012F Turntable Assembly R
3009 6549W1S013K Motor, AC Synchronous R
3010 4960W1A022A Plate R
3011 4890W1A045A Window,Glass R 4890W4A001G
3012 4370W1A011A Shaft,Turntable R
3024 MDX38927302 Grille,Vent R
3025 4810W1A150C Bracket,Lamp R
3026 5230W1A012C Filter,Grease R 2B72705B
3026 5230W1A012C Filter,Grease R 5230W1A012A
3026 5230W1A012C Filter,Grease R 5230W1A012B
3027 6549W1V006W Motor, AC Ventilation R
3028 6912W1Z004B Lamp,Incandescent R 6912W1Z002B
3029 4810W1A149A Bracket,Mount R
3034 3052W1A002A Cover,Resin R
3037 MJH38925501 Supporter R
4000 3500W1A028B Holder,Locker R
4001 3501W1A019D Holder Assembly,Locker R
4002 6600W1K001D Switch,Micro R
4003 6600W1K001C Switch,Micro R
4004 4510W3A012C Lever R
5000 0CZZW1H004B Capacitor,High Voltage R 0CZZW1H004G
5000 0CZZW1H004B Capacitor,High Voltage R 0CZZW1H002H
5000 0CZZW1H004B Capacitor,High Voltage R 0CZZW1H001Q
5001 3B74133Q Fuse,Time Delay R 3B74133K
5002 4810W1A141A Bracket,Capacitor R
9-3
Location 721.80039700 Part Name SVC Alternate
No. PART NO
5006 5208W0A006C Duct R
5008 6170W1D052R Transformer,high voltage R 6170W1D052U
5009 2B71165R Magnetron R
5010 6411W1A019M Power Cord Assembly R
5014 6877W1A597V Harness,Single R
5015 6912W1Z004A Lamp,Incandescent R
5016 6930W1A003E Thermostat R 6930W3A001S
5016 6930W1A003E Thermostat R EBG33435103
5018 6851W1A002B Cable,Assembly R 6021W3B001G
5018 6851W1A002B Cable,Assembly R 6021W3B001S
5024 5893W3A002D Fan Assembly R 5893W3A002C
5034 3300W1A046C Plate,Bottom R
5035 3300W1A052B Plate,Bottom R
5036 3550W3A095C Cover,Lamp R
5037 5230W1A011C Filter,Charcoal R 2B72706D
5037 5230W1A011C Filter,Charcoal R 5230W1A011A
5037 5230W1A011C Filter,Charcoal R 5230W1A011B
5038 6620G00007A Lamp Holder R
5039 MAZ37440501 Bracket R
5041 EAM35001801 Filter,AC Line R 2B72130F
5043 4930W1A068A Holder,Stirrer Fan R
5044 3550W1A126B Cover,Stirrer Fan R 3550W1A126A
5045 3550W1A189A Cover,Lamp R
5058 5892W1A003A Fan R
5067 4810W1A305B Bracket,Thermostat R
5337 3740W1A011B Supporter R
6000 3302W0A047M Plate,Base R
6001 3303W1A072N Plate Assembly,Base R
6008 3300W0A030A Plate,Mount R
6009 3861W1A043C Kit Assembly R
6010 4810W1A151A Bracket,Idle R
6011 4900W1A001B Damper R
W101 1SBF0402418 Screw,Taptite R
W102 4B70188C Screw,Customized R
W105 1TPL0402418 Screw,Tapping R
W106 1TPL0402818 Screw,Tapping R
W108 1TTL0402418 Screw,Tapping R
W109 1TTL0402818 Screw,Tapping R
W118 1TTG0402422 Screw,Tapping R
W130 1TPL0402618 Screw,Tapping R
W142 1TTL0402816 Screw,Tapping R
9-4
Part Reference list (1.6 Cuft)
For Model : 721.80033 Rev.1 Jun 18, 2007
Location 721.80033700 Part Name SVC Alternate
No. PART NO
*01 MFL39431001 Manual,Owners R
*02 MFL30502903 Manual,Service R
*04 MFL39433001 Manual,Installation R
*05 MEZ40037401 Label,Cooking Guide R
*06-1 4922W1A021E Card,Template R
*06-2 4922W5A058A Card,Template R
*07 MBM00607003 Card,Technical R
*10 3890W3Y925P Box R
1000 3213W1A049F Frame Assembly,Door R 3213W1A049J
1002 3536W1A012B Tape,Sealing R
1004 3552W1A032E Cover,Choke R 3552W1A063A
1005 ADC33688804 Door Assembly R
1006 4026W2A019A Locker R
1007 4970WRA001G Spring R
1008 MKC39429002 Window,Glass R
1009 MEB38925704 Handle,Door R
1381 AGM34653801 Parts Assembly(Door Panel+Cover) R
2004 ACM33689603 Controller Assembly,Keypad R
2006 6871W1A497C PCB Assembly,Sub R
2008 MAZ38922001 Bracket,Control Panel R
2018 0CZZW1M001C Capacitor,Film,Box R
2381 ACM34112801 Controller Assembly,Sub R
3001 3112W1F056S Case,Flat R
3002 1B71961H Tray,Glass R
3003 ABU33693602 Cavity Assembly,Coating R
3004 4051W3A001A Connector Assembly R
3008 5889W2A012F Turntable Assembly R
3009 6549W1S013K Motor, AC Synchronous R
3010 4960W1A022A Plate R
3011 4890W1A045A Window,Glass R 4890W4A001G
3012 4370W1A011A Shaft,Turntable R
3024 MDX38927302 Grille,Vent R
3025 4810W1A150C Bracket,Lamp R
3026 5230W1A012C Filter,Grease R 2B72705B
3026 5230W1A012C Filter,Grease R 5230W1A012A
3026 5230W1A012C Filter,Grease R 5230W1A012B
3027 6549W1V006W Motor, AC Ventilation R
3028 6912W1Z004B Lamp,Incandescent R 6912W1Z002B
3029 4810W1A149A Bracket,Mount R
3034 3052W1A002A Cover,Resin R
3037 MJH38925501 Supporter R
4000 3500W1A028B Holder,Locker R
4001 3501W1A019D Holder Assembly,Locker R
4002 6600W1K001D Switch,Micro R
4003 6600W1K001C Switch,Micro R
4004 4510W3A012C Lever R
5000 0CZZW1H004B Capacitor,High Voltage R 0CZZW1H004G
5000 0CZZW1H004B Capacitor,High Voltage R 0CZZW1H002H
5000 0CZZW1H004B Capacitor,High Voltage R 0CZZW1H001Q
5001 3B74133Q Fuse,Time Delay R 3B74133K
5002 4810W1A141A Bracket,Capacitor R
5006 5208W0A006C Duct R
5008 6170W1D052R Transformer,high voltage R 6170W1D052U
9-5
Location 721.80033700 Part Name SVC Alternate
No. PART NO
5009 2B71165R Magnetron R
5010 6411W1A019M Power Cord Assembly R
5014 6877W1A597V Harness,Single R
5015 6912W1Z004A Lamp,Incandescent R
5016 6930W1A003E Thermostat R 6930W3A001S
5016 6930W1A003E Thermostat R EBG33435103
5018 6851W1A002B Cable,Assembly R 6021W3B001G
5018 6851W1A002B Cable,Assembly R 6021W3B001S
5024 5893W3A002D Fan Assembly R 5893W3A002C
5034 3300W1A046C Plate,Bottom R
5035 3300W1A052B Plate,Bottom R
5036 3550W3A095C Cover,Lamp R
5037 5230W1A011C Filter,Charcoal R 2B72706D
5037 5230W1A011C Filter,Charcoal R 5230W1A011A
5037 5230W1A011C Filter,Charcoal R 5230W1A011B
5038 6620G00007A Lamp Holder R
5039 MAZ37440501 Bracket R
5041 EAM35001801 Filter,AC Line R 2B72130F
5043 4930W1A068A Holder,Stirrer Fan R
5044 3550W1A126B Cover,Stirrer Fan R 3550W1A126A
5045 3550W1A189A Cover,Lamp R
5058 5892W1A003A Fan R
5067 4810W1A305B Bracket,Thermostat R
5337 3740W1A011B Supporter R
6000 3302W0A047M Plate,Base R
6001 3303W1A072N Plate Assembly,Base R
6008 3300W0A030A Plate,Mount R
6009 3861W1A043C Kit Assembly R
6010 4810W1A151A Bracket,Idle R
6011 4900W1A001B Damper R
W101 1SBF0402418 Screw,Taptite R
W102 4B70188C Screw,Customized R
W105 1TPL0402418 Screw,Tapping R
W106 1TPL0402818 Screw,Tapping R
W108 1TTL0402418 Screw,Tapping R
W109 1TTL0402818 Screw,Tapping R
W118 1TTG0402422 Screw,Tapping R
W130 1TPL0402618 Screw,Tapping R
W142 1TTL0402816 Screw,Tapping R
9-6
P/NO : MFL30502903 Printed in Korea