2800 Tatabánya Document ID:

Address:
Cseresznyefa u. 60/3 Examination of ESD MUF_07_05_01D-5
Tel/Fax: 06/34 744-642
Mobil 1: 06/30 216-4583 properties under Page 1/1
Mobil 2: 06/30 335-6586 Revised 04
E-mail: [email protected] laboratory conditions Date of issue 2013.09.01

QUALIFICATION DATA SHEET: Protocol record and summary sheet

Introductory data

Serial number of the document: Customer detail:

EMJL20170912_1ESD_Dr.Schutz Company: Dr Schutz Group GmbH
Sample data: Name: Iakab Alpar
Flooring surface coated with Dr Position: Product Manager ESD Coatings
Manufacturer:
Schutz materials Email: [email protected]
Model number: See Annex I. Tel: 0040 743 147 517
Details of the qualifying officer:
Size/pcs.: 14 pcs Samples
Name: Lovász Gábor
Position: ESD laboratory manager
Colours: See Annex I.
Email: [email protected]
Sample photo: Tel: +36 30/418-8651
The test report was verified:
Name: Godó Attila
Position: ESD expert
Email: [email protected]
See Annex I.
Tel: 06 34/744-642

Conditions in the climate chamber:

1st measurement
Rating details: Temperature: 23.5 C°
Humidity: 49.0 %
Testing of flooring samples coated 2nd measurement
with Dr Schutz ESD Coatings in
Type of rating: accordance with EN 61340-5-1:2016
Temperature: -
and ANSI 20.20:2014 norms Humidity: -
3rd measurement
Temperature: -
Revision date: 2017.09.12.
Humidity: -

Content of the qualification report

QUALIFICATION DATA SHEET: Description of the sample, brief introduction and summary
ANNEX I. Measurement results obtained during the certification of the sample

Important! The qualification report is complete and valid only in the presence of all attachments.

Notes

Preparation of samples: 50%±2% RH, 23°C±2°C 48 hours and 72 hours

 2800 Tatabánya Document ID:
Address:
Cseresznyefa u. 60/3 Examination of ESD MUF_07_05_01D-5
Tel/Fax: 06/34 744-642
Mobil 1: 06/30 216-4583 properties under Page 1/1
Mobil 2: 06/30 335-6586 Revised 04
E-mail: [email protected] laboratory conditions Date of issue 2013.09.01

QUALIFICATION DATA SHEET: Protocol record and summary sheet

Introductory
Refference data
documents

IEC 61340-5-1:2016 - Electrostatics – Part 5-1: Protection of electronic devices from electrostatic
phenomena – General requirements

ANSI-ESD S20.20:2014 - For the Development of an Electrostatic Discharge Control Program for –
Protection of Electrical and Electronic Parts, Assemblies and Equipment (Excluding Electrically
Initiated Explosive Devices)

Data of the measuring instruments used during the review

Calibratio Calibration Calibration

Type Model Serial number
n name: number: validity:

Megohmmeter AIJGO-61 0022 Kalibra 59 K/62092 2018.02.28.

Temperature
and humidity AIJGO-61 22 Kalibra 59 K/62092 2018.02.28.
meter

Measurement Parameters and Legend

Rp-p Point to point resistance

Rgp Point to grounding resistance
Rsys. System resistance

Summary

Based on qualification measurements carried out under normal environmental conditions, it can be concluded that the
flooring samples coated with the Dr Schutz ESD Sealers meet the requirements of IEC 61340-5-1:2016 and ANSI/ESD
20.20 International ESD standards. From the measurements made with the copper grounding electrode it can be stated that
from the ESD point of view, the surface treatment with Dr Schutz coatings improves the homogeneity of the floors
independently of the layer system,so that floors properly ground the mobile devices like wagons, charts, chairs, etc. The
results also show that the test surfaces coated with Dr Schutz ESD coatings improve the suitability of floor and human
system resistance.

Date of completion of the report: 2017.09.22.

 2800 Tatabánya Document code
Address:
Cseresznyefa u. 60/3
MUF_07_05_01D-5
Tel/Fax: 06/34 744-642
Mobil 1: 06/30 216-4583 ESD audit and measuring report and Qualifier sheet Page 1/1
Mobil 2: 06/30 335-6586 Revised 04
E-mail: [email protected] Date of issue 2013.09.01

Measurement results Register number: EMJL20170912_1ESD_Dr.Schutz Review date: 2017.09.12.

Type of ESD floor for tests Required measurement results Comparison of measured results
Mesurement 1 Measurement 2 Measurement 3

Measuremen
Limits
number
Sample

t types
Date: 2017.09.12. Date: 2017.--.--. Date: 2017.--.--. Notes
Floor type Measured points
Measured Measured Measured
Low High value
Unit Compliance
value
Unit Compliance
value
Unit Compliance

Material: between points 1 and 2 Rp-p 1.0×104 Ω 1.0×109 Ω 173 kΩ OK - - - - - - Original floor
STO POX KU
615 between points 3 and 4 Rp-p 1.0×104 Ω 1.0×109 Ω 298 kΩ OK - - - - - -
(original Coated floor
flooring) between points 5 and 6 Rp-p 1.0×104 Ω 1.0×109 Ω 278 kΩ OK - - - - - -
Relation between the original and the
Dr. Schutz between points 9 and 7 Rp-p 1.0×104 Ω 1.0×109 Ω 111 kΩ OK - - - - - -
coated floor surface
Sample 2017_01

material
between point 9 and grounding Rgp 1.0×104 Ω 1.0×109 Ω 98.4 kΩ OK - - - - - - Original floor
layout: ESD
Color Base 2 between point 7 and grounding Rgp 1.0×104 Ω 1.0×109 Ω 879 kΩ OK - - - - - - Coated floor
coats
between point 9 and grounding
ESD TopCoat Rgp 1.0×104 Ω 1.0×109 Ω 100 GΩ NOK - - - - - - Original floor
(copper earth electrode)
1 coat
between point 7 and grounding 4 9
(copper earth electrode)
Rgp 1.0×10 Ω 1.0×10 Ω 9.41 MΩ OK - - - - - - Coated floor
System measurement to
original floor
Rsys. - 1.0×109 Ω 13.8 MΩ OK - - - - - - Original floor

System measurement to
coated floor
Rsys. - 1.0×109 Ω 6.36 MΩ OK - - - - - - Coated floor

Material: between points 1 and 2 Rp-p 1.0×104 Ω 1.0×109 Ω 157 kΩ OK - - - - - - Original floor
STO POX KU
611 between points 3 and 4 Rp-p 1.0×104 Ω 1.0×109 Ω 324 kΩ OK - - - - - -
(original Coated floor
4 9
flooring) between points 5 and 6 Rp-p 1.0×10 Ω 1.0×10 Ω 900 kΩ OK - - - - - -
Relation between the original and the
Dr. Schutz between points 9 and 7 Rp-p 1.0×104 Ω 1.0×109 Ω 110 kΩ OK - - - - - -
Sample 2017_02

coated floor surface

material
between point 9 and grounding Rgp 1.0×104 Ω 1.0×109 Ω 25.7 kΩ OK - - - - - - Original floor
layout: ESD
Color Base 2 Rgp 4 9
26.4 kΩ OK - - - - - - Coated floor
between point 7 and grounding 1.0×10 Ω 1.0×10 Ω
coats
between point 9 and grounding
ESD TopCoat Rgp 1.0×104 Ω 1.0×109 Ω 100 GΩ NOK - - - - - - Original floor
(copper earth electrode)
1 coat
between point 7 and grounding
(copper earth electrode)
Rgp 1.0×104 Ω 1.0×109 Ω 277 kΩ OK - - - - - - Coated floor
System measurement to 9
Rsys. - 1.0×10 Ω 625 MΩ OK - - - - - - Original floor
original floor
System measurement to
coated floor
Rsys. - 1.0×109 Ω 7.74 MΩ OK - - - - - - Coated floor
 2800 Tatabánya Document code
Address:
Cseresznyefa u. 60/3
MUF_07_05_01D-5
Tel/Fax: 06/34 744-642
Mobil 1: 06/30 216-4583 ESD audit and measuring report and Qualifier sheet Page 1/1
Mobil 2: 06/30 335-6586 Revised 04
E-mail: [email protected] Date of issue 2013.09.01

Measurement results Register number: EMJL20170912_1ESD_Dr.Schutz Review date: 2017.09.12.

Type of ESD floor for tests Required measurement results Comparison of measured results
Mesurement 1 Measurement 2 Measurement 3

Measuremen
Limits
number
Sample

t types
Date: 2017.09.12. Date: 2017.--.--. Date: 2017.--.--. Notes
Floor type Measured points
Measured Measured Measured
Low High value
Unit Compliance
value
Unit Compliance
value
Unit Compliance

Material: between points 1 and 2 Rp-p 1.0×104 Ω 1.0×109 Ω 1.73 MΩ OK - - - - - - Original floor
STO POX KU
613 between points 3 and 4 Rp-p 1.0×104 Ω 1.0×109 Ω 275 kΩ OK - - - - - -
(original Coated floor
flooring) between points 5 and 6 Rp-p 1.0×104 Ω 1.0×109 Ω 660 kΩ OK - - - - - -
Relation between the original and the
Dr. Schutz between points 9 and 7 Rp-p 1.0×104 Ω 1.0×109 Ω 674 kΩ OK - - - - - -
Sample 2017_03

coated floor surface

material
between point 9 and grounding Rgp 1.0×104 Ω 1.0×109 Ω 443 kΩ OK - - - - - - Original floor
layout: ESD
Color Base 2 between point 7 and grounding Rgp 1.0×104 Ω 1.0×109 Ω 32.1 kΩ OK - - - - - - Coated floor
coats
between point 9 and grounding
ESD TopCoat Rgp 1.0×10 Ω4 9
1.0×10 Ω 38.5 MΩ OK - - - - - - Original floor
(copper earth electrode)
1 coat
between point 7 and grounding
(copper earth electrode)
Rgp 1.0×104 Ω 1.0×109 Ω 3.3 MΩ OK - - - - - - Coated floor
System measurement to
original floor
Rsys. - 1.0×109 Ω 12.5 MΩ OK - - - - - - Original floor
System measurement to 9
Rsys. - 1.0×10 Ω 8.43 MΩ OK - - - - - - Coated floor
coated floor
Material: between points 1 and 2 Rp-p 1.0×104 Ω 1.0×109 Ω 37.7 MΩ OK - - - - - - Original floor
Tarkett TORO
(original between points 3 and 4 Rp-p 1.0×104 Ω 1.0×109 Ω 143 kΩ OK - - - - - -
flooring) Coated floor
4 9
between points 5 and 6 Rp-p 1.0×10 Ω 1.0×10 Ω 162 kΩ OK - - - - - -
Dr. Schutz Relation between the original and the
material between points 9 and 7 Rp-p 1.0×104 Ω 1.0×109 Ω 19.5 MΩ OK - - - - - -
Sample 2017_04

coated floor surface

layout:
between point 9 and grounding Rgp 1.0×104 Ω 1.0×109 Ω 14 MΩ OK - - - - - - Original floor
ESD Color
Base 2 coats Rgp 4 9
100 kΩ OK - - - - - - Coated floor
between point 7 and grounding 1.0×10 Ω 1.0×10 Ω
ESD TopCoat
between point 9 and grounding
1 coat Rgp 1.0×104 Ω 1.0×109 Ω 132 MΩ OK - - - - - - Original floor
(copper earth electrode)
between point 7 and grounding
(copper earth electrode)
Rgp 1.0×104 Ω 1.0×109 Ω 116 kΩ OK - - - - - - Coated floor
System measurement to 9
Rsys. - 1.0×10 Ω 66.8 MΩ OK - - - - - - Original floor
original floor
System measurement to
coated floor
Rsys. - 1.0×109 Ω 14.9 MΩ OK - - - - - - Coated floor
 2800 Tatabánya Document code
Address:
Cseresznyefa u. 60/3
MUF_07_05_01D-5
Tel/Fax: 06/34 744-642
Mobil 1: 06/30 216-4583 ESD audit and measuring report and Qualifier sheet Page 1/1
Mobil 2: 06/30 335-6586 Revised 04
E-mail: [email protected] Date of issue 2013.09.01

Measurement results Register number: EMJL20170912_1ESD_Dr.Schutz Review date: 2017.09.12.

Type of ESD floor for tests Required measurement results Comparison of measured results
Mesurement 1 Measurement 2 Measurement 3

Measuremen
Limits
number
Sample

t types
Date: 2017.09.12. Date: 2017.--.--. Date: 2017.--.--. Notes
Floor type Measured points
Measured Measured Measured
Low High value
Unit Compliance
value
Unit Compliance
value
Unit Compliance

Material: between points 1 and 2 Rp-p 1.0×104 Ω 1.0×109 Ω 10.5 MΩ OK - - - - - - Original floor
Graboplast
ESD PVC between points 3 and 4 Rp-p 1.0×104 Ω 1.0×109 Ω 384 kΩ OK - - - - - -
(original Coated floor
flooring) between points 5 and 6 Rp-p 1.0×104 Ω 1.0×109 Ω 333 kΩ OK - - - - - -
Relation between the original and the
Dr. Schutz between points 9 and 7 Rp-p 1.0×104 Ω 1.0×109 Ω 1.48 MΩ OK - - - - - -
Sample 2017_05

coated floor surface

material
between point 9 and grounding Rgp 1.0×104 Ω 1.0×109 Ω 7.2 MΩ OK - - - - - - Original floor
layout:
ESD Color between point 7 and grounding Rgp 1.0×104 Ω 1.0×109 Ω 6.19 MΩ OK - - - - - - Coated floor
Base 2 coats
between point 9 and grounding
ESD TopCoat Rgp 1.0×10 Ω4 9
1.0×10 Ω 11.3 MΩ OK - - - - - - Original floor
(copper earth electrode)
1 coat
between point 7 and grounding
(copper earth electrode)
Rgp 1.0×104 Ω 1.0×109 Ω 6.66 MΩ OK - - - - - - Coated floor
System measurement to
original floor
Rsys. - 1.0×109 Ω 66.7 MΩ OK - - - - - - Original floor
System measurement to 9
Rsys. - 1.0×10 Ω 45.7 MΩ OK - - - - - - Coated floor
coated floor
Material: between points 1 and 2 Rp-p 1.0×104 Ω 1.0×109 Ω 94.8 kΩ OK - - - - - - Original floor
STO POX KU
615 between points 3 and 4 Rp-p 1.0×104 Ω 1.0×109 Ω 189 kΩ OK - - - - - -
(original Coated floor
4 9
flooring) between points 5 and 6 Rp-p 1.0×10 Ω 1.0×10 Ω 143 kΩ OK - - - - - -
Relation between the original and the
Dr. Schutz between points 9 and 7 Rp-p 1.0×104 Ω 1.0×109 Ω 169 kΩ OK - - - - - -
Sample 2017_06

coated floor surface

material
between point 9 and grounding Rgp 1.0×104 Ω 1.0×109 Ω 31.2 kΩ OK - - - - - - Original floor
layout:
ESD BaseCoat Rgp 4 9
145 kΩ OK - - - - - - Coated floor
between point 7 and grounding 1.0×10 Ω 1.0×10 Ω
2 rcoats
between point 9 and grounding
ESD TopCoat Rgp 1.0×104 Ω 1.0×109 Ω 68.2 GΩ NOK - - - - - - Original floor
(copper earth electrode)
1 coat
between point 7 and grounding
(copper earth electrode)
Rgp 1.0×104 Ω 1.0×109 Ω 5.41 MΩ OK - - - - - - Coated floor
System measurement to 9
Rsys. - 1.0×10 Ω 17.4 MΩ OK - - - - - - Original floor
original floor
System measurement to
coated floor
Rsys. - 1.0×109 Ω 6.54 MΩ OK - - - - - - Coated floor
 2800 Tatabánya Document code
Address:
Cseresznyefa u. 60/3
MUF_07_05_01D-5
Tel/Fax: 06/34 744-642
Mobil 1: 06/30 216-4583 ESD audit and measuring report and Qualifier sheet Page 1/1
Mobil 2: 06/30 335-6586 Revised 04
E-mail: [email protected] Date of issue 2013.09.01

Measurement results Register number: EMJL20170912_1ESD_Dr.Schutz Review date: 2017.09.12.

Type of ESD floor for tests Required measurement results Comparison of measured results
Mesurement 1 Measurement 2 Measurement 3

Measuremen
Limits
number
Sample

t types
Date: 2017.09.12. Date: 2017.--.--. Date: 2017.--.--. Notes
Floor type Measured points
Measured Measured Measured
Low High value
Unit Compliance
value
Unit Compliance
value
Unit Compliance

Material: between points 1 and 2 Rp-p 1.0×104 Ω 1.0×109 Ω 170 kΩ OK - - - - - - Original floor
STO POX KU
611 between points 3 and 4 Rp-p 1.0×104 Ω 1.0×109 Ω 190 kΩ OK - - - - - -
(original Coated floor
flooring) between points 5 and 6 Rp-p 1.0×104 Ω 1.0×109 Ω 120 kΩ OK - - - - - -
Relation between the original and the
Dr. Schutz between points 9 and 7 Rp-p 1.0×104 Ω 1.0×109 Ω 100 kΩ OK - - - - - -
Sample 2017_07

coated floor surface

material
between point 9 and grounding Rgp 1.0×104 Ω 1.0×109 Ω 25 kΩ OK - - - - - - Original floor
layout:
ESD BaseCoat between point 7 and grounding Rgp 1.0×104 Ω 1.0×109 Ω 52.2 kΩ OK - - - - - - Coated floor
2 coats
between point 9 and grounding
ESD TopCoat Rgp 1.0×10 Ω4 9
1.0×10 Ω 100 GΩ NOK - - - - - - Original floor
(copper earth electrode)
1 coat
between point 7 and grounding
(copper earth electrode)
Rgp 1.0×104 Ω 1.0×109 Ω 505 kΩ OK - - - - - - Coated floor
System measurement to
original floor
Rsys. - 1.0×109 Ω 312 MΩ OK - - - - - - Original floor
System measurement to 9
Rsys. - 1.0×10 Ω 6.74 MΩ OK - - - - - - Coated floor
coated floor
Material: between points 1 and 2 Rp-p 1.0×104 Ω 1.0×109 Ω 1.61 MΩ OK - - - - - - Original floor
STO POX 613
(original between points 3 and 4 Rp-p 1.0×104 Ω 1.0×109 Ω 167 kΩ OK - - - - - -
flooring) Coated floor
4 9
between points 5 and 6 Rp-p 1.0×10 Ω 1.0×10 Ω 264 kΩ OK - - - - - -
Dr. Schutz Relation between the original and the
material between points 9 and 7 Rp-p 1.0×104 Ω 1.0×109 Ω 975 kΩ OK - - - - - -
Sample 2017_08

coated floor surface

layout:
between point 9 and grounding Rgp 1.0×104 Ω 1.0×109 Ω 946 kΩ OK - - - - - - Original floor
ESD BaseCoat
2 coats Rgp 4 9
132 kΩ OK - - - - - - Coated floor
between point 7 and grounding 1.0×10 Ω 1.0×10 Ω
ESD TopCoat
between point 9 and grounding
1 coat Rgp 1.0×104 Ω 1.0×109 Ω 1.19 MΩ OK - - - - - - Original floor
(copper earth electrode)
between point 7 and grounding
(copper earth electrode)
Rgp 1.0×104 Ω 1.0×109 Ω 3.38 MΩ OK - - - - - - Coated floor
System measurement to 9
Rsys. - 1.0×10 Ω 11.5 MΩ OK - - - - - - Original floor
original floor
System measurement to
coated floor
Rsys. - 1.0×109 Ω 7.12 MΩ OK - - - - - - Coated floor
 2800 Tatabánya Document code
Address:
Cseresznyefa u. 60/3
MUF_07_05_01D-5
Tel/Fax: 06/34 744-642
Mobil 1: 06/30 216-4583 ESD audit and measuring report and Qualifier sheet Page 1/1
Mobil 2: 06/30 335-6586 Revised 04
E-mail: [email protected] Date of issue 2013.09.01

Measurement results Register number: EMJL20170912_1ESD_Dr.Schutz Review date: 2017.09.12.

Type of ESD floor for tests Required measurement results Comparison of measured results
Mesurement 1 Measurement 2 Measurement 3

Measuremen
Limits
number
Sample

t types
Date: 2017.09.12. Date: 2017.--.--. Date: 2017.--.--. Notes
Floor type Measured points
Measured Measured Measured
Low High value
Unit Compliance
value
Unit Compliance
value
Unit Compliance

Material: between points 1 and 2 Rp-p 1.0×104 Ω 1.0×109 Ω 139 MΩ OK - - - - - - Original floor
Tarkett TORO
(original between points 3 and 4 Rp-p 1.0×104 Ω 1.0×109 Ω 538 kΩ OK - - - - - -
flooring) Coated floor
between points 5 and 6 Rp-p 1.0×104 Ω 1.0×109 Ω 486 MΩ OK - - - - - -
Dr. Schutz Relation between the original and the
material between points 9 and 7 Rp-p 1.0×104 Ω 1.0×109 Ω 84.4 MΩ OK - - - - - -
Sample 2017_09

coated floor surface

layout:
between point 9 and grounding Rgp 1.0×104 Ω 1.0×109 Ω 75 MΩ OK - - - - - - Original floor
ESD BaseCoat
2 coats between point 7 and grounding Rgp 1.0×104 Ω 1.0×109 Ω 268 kΩ OK - - - - - - Coated floor
ESD TopCoat
between point 9 and grounding
1 coat Rgp 1.0×10 Ω4 9
1.0×10 Ω 417 MΩ OK - - - - - - Original floor
(copper earth electrode)
between point 7 and grounding
(copper earth electrode)
Rgp 1.0×104 Ω 1.0×109 Ω 496 kΩ OK - - - - - - Coated floor
System measurement to
original floor
Rsys. - 1.0×109 Ω 40.4 MΩ OK - - - - - - Original floor
System measurement to 9
Rsys. - 1.0×10 Ω 21.7 MΩ OK - - - - - - Coated floor
coated floor
Material: between points 1 and 2 Rp-p 1.0×104 Ω 1.0×109 Ω 169 MΩ OK - - - - - - Original floor
STO POX KU
615 between points 3 and 4 Rp-p 1.0×104 Ω 1.0×109 Ω 688 kΩ OK - - - - - -
(original Coated floor
4 9
flooring) between points 5 and 6 Rp-p 1.0×10 Ω 1.0×10 Ω 1.22 MΩ OK - - - - - -
Relation between the original and the
Dr. Schutz between points 9 and 7 Rp-p 1.0×104 Ω 1.0×109 Ω 1.18 MΩ OK - - - - - -
Sample 2017_10

coated floor surface

material
between point 9 and grounding Rgp 1.0×104 Ω 1.0×109 Ω 39.2 kΩ OK - - - - - - Original floor
layout:
ESD BaseCoat Rgp 4 9
823 kΩ OK - - - - - - Coated floor
between point 7 and grounding 1.0×10 Ω 1.0×10 Ω
1 coat
between point 9 and grounding
ESD TopCoat Rgp 1.0×104 Ω 1.0×109 Ω 100 GΩ NOK - - - - - - Original floor
(copper earth electrode)
1 coat
between point 7 and grounding
(copper earth electrode)
Rgp 1.0×104 Ω 1.0×109 Ω 2.44 MΩ OK - - - - - - Coated floor
System measurement to 9
Rsys. - 1.0×10 Ω 23.7 MΩ OK - - - - - - Original floor
original floor
System measurement to
coated floor
Rsys. - 1.0×109 Ω 7.6 MΩ OK - - - - - - Coated floor
 2800 Tatabánya Document code
Address:
Cseresznyefa u. 60/3
MUF_07_05_01D-5
Tel/Fax: 06/34 744-642
Mobil 1: 06/30 216-4583 ESD audit and measuring report and Qualifier sheet Page 1/1
Mobil 2: 06/30 335-6586 Revised 04
E-mail: [email protected] Date of issue 2013.09.01

Measurement results Register number: EMJL20170912_1ESD_Dr.Schutz Review date: 2017.09.12.

Type of ESD floor for tests Required measurement results Comparison of measured results
Mesurement 1 Measurement 2 Measurement 3

Measuremen
Limits
number
Sample

t types
Date: 2017.09.12. Date: 2017.--.--. Date: 2017.--.--. Notes
Floor type Measured points
Measured Measured Measured
Low High value
Unit Compliance
value
Unit Compliance
value
Unit Compliance

Material: between points 1 and 2 Rp-p 1.0×104 Ω 1.0×109 Ω 150 kΩ OK - - - - - - Original floor
STO POX KU
611 between points 3 and 4 Rp-p 1.0×104 Ω 1.0×109 Ω 2.12 MΩ OK - - - - - -
(original Coated floor
flooring) between points 5 and 6 Rp-p 1.0×104 Ω 1.0×109 Ω 762 kΩ OK - - - - - -
Relation between the original and the
Dr. Schutz between points 9 and 7 Rp-p 1.0×104 Ω 1.0×109 Ω 150 kΩ OK - - - - - -
Sample 2017_11

coated floor surface

material
between point 9 and grounding Rgp 1.0×104 Ω 1.0×109 Ω 55.4 kΩ OK - - - - - - Original floor
layout:
ESD BaseCoat between point 7 and grounding Rgp 1.0×104 Ω 1.0×109 Ω 104 kΩ OK - - - - - - Coated floor
1 coat
between point 9 and grounding
ESD TopCoat Rgp 1.0×10 Ω4 9
1.0×10 Ω 100 GΩ NOK - - - - - - Original floor
(copper earth electrode)
1 coat
between point 7 and grounding
(copper earth electrode)
Rgp 1.0×104 Ω 1.0×109 Ω 4.36 MΩ OK - - - - - - Coated floor
System measurement to
original floor
Rsys. - 1.0×109 Ω 1.72 GΩ NOK - - - - - - Original floor
System measurement to 9
Rsys. - 1.0×10 Ω 9.7 MΩ OK - - - - - - Coated floor
coated floor
Material: between points 1 and 2 Rp-p 1.0×104 Ω 1.0×109 Ω 1.1 MΩ OK - - - - - - Original floor
STO POX KU
613 between points 3 and 4 Rp-p 1.0×104 Ω 1.0×109 Ω 398 kΩ OK - - - - - -
(original Coated floor
4 9
flooring) between points 5 and 6 Rp-p 1.0×10 Ω 1.0×10 Ω 498 kΩ OK - - - - - -
Relation between the original and the
Dr. Schutz between points 9 and 7 Rp-p 1.0×104 Ω 1.0×109 Ω 232 kΩ OK - - - - - -
Sample 2017_12

coated floor surface

material
between point 9 and grounding Rgp 1.0×104 Ω 1.0×109 Ω 67.5 kΩ OK - - - - - - Original floor
layout:
ESD BaseCoat Rgp 4 9
114 kΩ OK - - - - - - Coated floor
between point 7 and grounding 1.0×10 Ω 1.0×10 Ω
1 coat
between point 9 and grounding
ESD TopCoat Rgp 1.0×104 Ω 1.0×109 Ω 6.99 MΩ OK - - - - - - Original floor
(copper earth electrode)
1 coat
between point 7 and grounding
(copper earth electrode)
Rgp 1.0×104 Ω 1.0×109 Ω 573 kΩ OK - - - - - - Coated floor
System measurement to 9
Rsys. - 1.0×10 Ω 10.3 MΩ OK - - - - - - Original floor
original floor
System measurement to
coated floor
Rsys. - 1.0×109 Ω 8.04 MΩ OK - - - - - - Coated floor
 2800 Tatabánya Document code
Address:
Cseresznyefa u. 60/3
MUF_07_05_01D-5
Tel/Fax: 06/34 744-642
Mobil 1: 06/30 216-4583 ESD audit and measuring report and Qualifier sheet Page 1/1
Mobil 2: 06/30 335-6586 Revised 04
E-mail: [email protected] Date of issue 2013.09.01

Measurement results Register number: EMJL20170912_1ESD_Dr.Schutz Review date: 2017.09.12.

Type of ESD floor for tests Required measurement results Comparison of measured results
Mesurement 1 Measurement 2 Measurement 3

Measuremen
Limits
number
Sample

t types
Date: 2017.09.12. Date: 2017.--.--. Date: 2017.--.--. Notes
Floor type Measured points
Measured Measured Measured
Low High value
Unit Compliance
value
Unit Compliance
value
Unit Compliance

Material: between points 1 and 2 Rp-p 1.0×104 Ω 1.0×109 Ω 68 MΩ OK - - - - - - Original floor

Tarkett TORO
(original between points 3 and 4 Rp-p 1.0×104 Ω 1.0×109 Ω 881 kΩ OK - - - - - -
flooring) Coated floor
between points 5 and 6 Rp-p 1.0×104 Ω 1.0×109 Ω 764 kΩ OK - - - - - -
Dr. Schutz Relation between the original and the
material between points 9 and 7 Rp-p 1.0×104 Ω 1.0×109 Ω 1.38 MΩ OK - - - - - -
Sample 2017_13

coated floor surface

layout:
between point 9 and grounding Rgp 1.0×104 Ω 1.0×109 Ω 1.51 MΩ OK - - - - - - Original floor
ESD BaseCoat
1 coat between point 7 and grounding Rgp 1.0×104 Ω 1.0×109 Ω 372 kΩ OK - - - - - - Coated floor
ESD TopCoat
between point 9 and grounding
1 coat Rgp 1.0×10 Ω4 9
1.0×10 Ω 135 MΩ OK - - - - - - Original floor
(copper earth electrode)
between point 7 and grounding
(copper earth electrode)
Rgp 1.0×104 Ω 1.0×109 Ω 1.51 MΩ OK - - - - - - Coated floor
System measurement to
original floor
Rsys. - 1.0×109 Ω 47.7 MΩ OK - - - - - - Original floor
System measurement to 9
Rsys. - 1.0×10 Ω 18.5 MΩ OK - - - - - - Coated floor
coated floor
Material: between points 1 and 2 Rp-p 1.0×104 Ω 1.0×109 Ω 90.5 MΩ OK - - - - - - Original floor
Graboplast
ESD PVC between points 3 and 4 Rp-p 1.0×104 Ω 1.0×109 Ω 6.56 MΩ OK - - - - - -
(original Coated floor
4 9
flooring) between points 5 and 6 Rp-p 1.0×10 Ω 1.0×10 Ω 4.33 MΩ OK - - - - - -
Relation between the original and the
Dr. Schutz between points 9 and 7 Rp-p 1.0×104 Ω 1.0×109 Ω 31.1 MΩ OK - - - - - -
Sample 2017_14

coated floor surface

material
between point 9 and grounding Rgp 1.0×104 Ω 1.0×109 Ω 70.1 MΩ OK - - - - - - Original floor
layout:
ESD BaseCoat Rgp 4 9
20.6 MΩ OK - - - - - - Coated floor
between point 7 and grounding 1.0×10 Ω 1.0×10 Ω
1 coat
between point 9 and grounding
ESD TopCoat Rgp 1.0×104 Ω 1.0×109 Ω 72.3 MΩ OK - - - - - - Original floor
(copper earth electrode)
1 coat
between point 7 and grounding
(copper earth electrode)
Rgp 1.0×104 Ω 1.0×109 Ω 50.9 MΩ OK - - - - - - Coated floor
System measurement to 9
Rsys. - 1.0×10 Ω 88.3 MΩ OK - - - - - - Original floor
original floor
System measurement to
coated floor
Rsys. - 1.0×109 Ω 76 MΩ OK - - - - - - Coated floor
 2800 Tatabánya Document code
Address:
Cseresznyefa u. 60/3
MUF_07_05_01D-5
Tel/Fax: 06/34 744-642
Mobil 1: 06/30 216-4583 ESD audit and measuring report and Qualifier sheet Page 1/1
Mobil 2: 06/30 335-6586 Revised 04
E-mail: [email protected] Date of issue 2013.09.01

Measurement results Register number: EMJL20170912_1ESD_Dr.Schutz Review date: 2017.09.12.

Type of ESD floor for tests Required measurement results Comparison of measured results
Mesurement 1 Measurement 2 Measurement 3

Measuremen
Limits
number
Sample

t types
Date: 2017.09.12. Date: 2017.--.--. Date: 2017.--.--. Notes
Floor type Measured points
Measured Measured Measured
Low High value
Unit Compliance
value
Unit Compliance
value
Unit Compliance

Material:

Measurement points

6
Coated surface

3 7 4

Original flooring
1 9 2

Grounding point
 2800 Tatabánya Document ID:
Address:
Cseresznyefa u. 60/3
Tel/Fax: 06/34 744-642 Examination of ESD properties under MUF_07_05_01D-5
Mobil 1: 06/30 216-4583 Page: 1/1
Mobil 2: 06/30 335-6586 laboratory conditions Revised: 04
E-mail: [email protected] Date of issue: 2013.09.01

II. Annex: Schematic diagram of the measurements

Serial number: EMJL20170912_1ESD_Dr.Schutz Date of issue 2017.09.12.

Sample indentification Requested measurement results

Sample number

Measurement
Measurement limit
The schematic diagram or photo of the measurements

types
Sample type Notes

Low: High:

Gigaohm meter

Measurement points: see

- Rp-p - 1.0×109 Ω
annex I

Weight electrode
Weight electrode

Flooring

Gigaohm meter

Weight electrode
Measurement points: see Grounding
- Rgp - 1.0×109 Ω
annex I point

Flooring

Flooring
samples coated
with Dr Schutz Gigaohm meter
materials

Measurement points: see

- Rgp - 1.0×109 Ω Cooper
annex I grounding
Grounding
point

Flooring

Gigaohm
Man
metter
standing
on an ESD
Floor

Measurement points: see

- Rsys. - 1.0×109 Ω
annex I
Grounding
point

Flooring