DR Engp I 1.1 R.11
DR Engp I 1.1 R.11
Revision 11
ENGINEERING GUIDELINES
Production Development and Technology
Piping
Approval: SRGE/ESUP
Verification: SRGE/ESUP/EEA
Execution: SRGE/ESUP/EEA/EEAT
Approved in 20/07/2020
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
INDEX
1 SCOPE ........................................................................................................................................3
2 NORMATIVE REFERENCES .....................................................................................................3
3 SYMBOLS AND ABBREVIATED TERMS..................................................................................7
4 PIPING TAGGING SYSTEM .....................................................................................................10
5 PIPING SPECIFICATION CODE RULE....................................................................................11
6 SERVICES FOR TOPSIDE PIPING SPECS .............................................................................12
7 LIST OF TOPSIDE PIPING SPECS ..........................................................................................14
8 SERVICES FOR HULL PIPING SPECS ...................................................................................18
9 LIST OF HULL PIPING SPECS ................................................................................................21
Annex
A. Valves and Valve Datasheets
B. Pipes, Fittings and Accessories and Datasheets
C. Typical Arrangement for Drain&Vent and Instruments
D. Piping Material Selection for Corrosive HC and Produced Water
E. Flange Isolation Kit
F. Requirements for Piping internal Coating (cancelled)
G. Welding Requirements (cancelled)
H. Requirements for FRP Pipes and Fittings
J. Piping Weld Inspection (cancelled)
K. Pressure-Safety Valves
- Rev. 11 - Page 2 of 21
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
1 SCOPE
This Guideline standardizes piping and valves materials for use in oil and gas exploration and production facilities.
This document specifies requirements for acquisition of: pipes, valves, fittings, flanges, gaskets bolts and nuts.
Aspects of design, performance, materials, fabrication, testing, inspection, marking, storage, expedition and
documentation are covered.
The designer is responsable for selecting the piping material specification (spec) taking into account its limitations,
such as: service, pressure and temperature.
2 NORMATIVE REFERENCES
Note: The Standards referred herein shall be considered in their latest edition/revision.
API RP 14E - Recommended Practice for Design and Installation of offshore Production Platform Piping Systems.
API SPEC 6D ISO 14313 - Petroleum and Natural Gas Industries – Pipeline Transportation Systems-Pipeline Valves.
API STD 594 - Check Valves: Wafer, Wafer-Lug, and Double Flanged Type.
API STD 600 ISO 10434 – Bolted Bonnet Steel Gate Valves for Petroleum and Natural Gas Industries.
API STD 602 - ISO 15671 – Compact Steel Gate Valves – Flanged, Threaded, Welding, and Extended – Body Ends.
API STD 607 - Fire Test for Quarter-turn Valves and Valves Equipped with Nonmetallic Seats
API STD 609 - Butterfly Valves: Double Flanged, Lug and Wafer – Type.
ASME B1.1 - Unified Inch Screw Threads (UN and UNR Thread Form).
ASME B16.1 - Cast Iron Pipe Flanges and Flanged Fittings Classes 25, 125 and 250.
ASME B16.5 - Pipe flanges and flanged fittings NPS 1/2 through NPS 24 metric/inch standard revision e ASME B16.5
ASME B16.20 - Metallic gaskets for pipe flanges ring-joint, spiral-wound, and jacketed.
ASME B16.28 - Wrought Steel Buttwelding Short Radius Elbows and Returns.
ASME B16.47 - Large diameter Steel Flanges (NPS 26 through NPS 60).
ASME B16.5 - Pipe Flanges and Flanged Fittings: NPS 1/2 through NPS 24 Metric/Inch Standard
- Rev. 11 - Page 3 of 21
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
ASME B31.4 - Pipeline Transportation Systems for Liquid Hydrocarbons and Other Liquids
ASME B31.8 - Gas Transmission and Distribution Piping Systems
ASTM A105 - Standard Specification for Aço carbonoForgings for Piping Applications.
ASTM A106 - Standard Specification for Seamless Aço carbonoPipe for High-Temperature Service.
ASTM A123 - Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products.
ASTM A126 - Standard Specification for Gray Iron Castings for Valves, Flanges, and Pipe Fittings.
ASTM A182 - Standard Specification for Forged or Rolled Alloy-.Steel Pipe Flanges, Forged Fittings, and Valves and
Parts for High-Temperature Service.
ASTM A193 - Standard Specification for Alloy-Steel and Stainless Steel Bolting Materials for High-Temperature
Service.
ASTM A194 - Standard specification for carbon and alloy steel nuts for bolts for high pressure or high temperature
service, or both.
ASTM A216 - Standard Specification for Steel Castings, Carbon, Suitable for Fusion Welding, High-Temperature
Service.
ASTM A234 - Standard Specification for Piping Fittings of Wrought Aço carbonoand Alloy Steel for Moderate and High
Temperature Service.
ASTM A269 - Standard Specification for Seamless and Welded Austenitic Stainless Steel Tubing for General Service
ASTM A312 - Standard Specification for Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel
Pipes.
ASTM A320 - Standard Specification for Alloy-Steel and Stainless Steel Bolting Materials Low High-Temperature
Service.
ASTM A333 - Standard Specification for Seamless and Welded Steel Pipe for Low-Temperature Service.
ASTM A350 - Standard Specification for Carbon and Low-Alloy Steel Forgings, Requiring Notch Toughness Testing
for Piping Components.
ASTM A351 - Standard Specification for Castings, Austenitic, Austenitic-Ferritic (Duplex), for Pressure-Containing
Parts.
ASTM A352 - Standard Specification for Steel Castings, Ferritic and Martensitic, for Pressure-Containing Parts,
Suitable for Low-Temperature Service.
ASTM A358 - Standard Specification for Electric-Fusion-Welded Austenitic Chromium-Nickel Stainless Steel Pipe for
High-Temperature Service and General Applications
ASTM A403 - Standard Specification for Wrought Austenitic Stainless Steel Piping Fittings.
- Rev. 11 - Page 4 of 21
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
ASTM A420 - Standard Specification for Piping Fittings of Wrought Aço carbonoand Alloy Steel for Low-Temperature
Service.
ASTM A487 - Standard Specification for Steel Castings Suitable for Pressure Service.
ASTM A522 - Standard Specification for Forged or Rolled 8 and 9% Nickel Alloy Steel Flanges, Fittings, Valves, and
Parts for Low-Temperature Service
ASTM A564 - Standard Specification for Hot-Rolled and Cold-Finished Age-Hardening Stainless Steel Bars and
Shapes.
ASTM A671 - Standard Specification for Eletric-Fusion-Welded Steel Pipe for Atmospheric and Lower Temperatures.
ASTM A694 - Standard Specification for Carbon and Alloy Steel Forgings for Pipe Flanges, Fittings, Valves, and Parts
for High-Pressure Transmission Service.
ASTM A733 - Standard Specification for Welded and Seamless Carbon Steel and Austenitic Stainless Steel Pipe
Nipples
ASTM A790 - Standard Specification for Seamless and Welded Ferritic/Austenitic Stainless Steel Pipe.
ASTM A815 - Standard Specification for Wrought Ferritic, Ferritic/Austenitic, and Martensitic Stainless Steel Piping
Fittings.
ASTM A928 - Standard Specification for Ferritic/Austenitic (Duplex) Stainless Steel Pipe Electric Fusion Welded with
Addition of Filler Metal
ASTM A995 - Standard Specification for Castings, Austenitic-Ferritic (Duplex) Stainless Steel, for Pressure-Containing
Parts
ASTM B62 - Standard Specification for Composition Bronze or Ounce Metal Castings.
ASTM B366 - Standard Specification for Factory-Made Wrought Nickel and Nickel Alloy Fittings
ASTM B444 - Specification for Nickel-Chromium-Molybdenum-Columbium Alloys (UNS N06625 and UNS N06852)
and Nickel-Chromium-Molybdenum-Silicon Alloy (UNS N06219) Pipe and Tube
ASTM B584 - Standard Specification for Copper Alloy Sand Castings for General Applications.
ASTM D1784 - Standard Specification for Rigid Poly (Vinyl Chloride) (PVC) Compounds and Chlorinated Poly (Vinyl
Chloride) (CPVC) Compounds.
ASTM D1785 - Standard Specification for Poly (Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80 and 120.
ASTM D2467 - Standard Specification for Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80.
ASTM D3567 - Standard Practice for Determining Dimensions of Fiberglass (Glass-Fiber-Reinforced Thermosetting
Resin) Pipe and Fittings R (2002).
ASTM D4024 - Standard Specification for Machine Made "Fiberglass" (Glass-Fiber-Reinforced Thermosetting Resin)
Flanges (2000).
ASTM F1173 - Standard Specification for Thermosetting Resin Fiberglass Pipe Systems to be used for Marine
Applications (2001).
- Rev. 11 - Page 5 of 21
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
ASTM F1387 - Standard Specification for Performance of Piping and Tubing Mechanically Attached Fittings
ASTM F439 - Standard Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80.
BSI BS 1873 - Stell Globe and Globe Stop and Check Valves (flanged and butt-welding ends) for the Petroleum,
Petrochemical and Allied Industries.
BSI BS 3799 - Steel Pipe Fittings, Screwed and Socket-Welding for the Petroleum Industry.
BSI BS 5152 - Cast Iron Globe and Globe Stop and Check Valves for General Purposes.
BSI BS 5351 - Steel Ball Valves for the Petroleum, Petrochemical and Allied Industries.
BSI BS 5352 - Steel Wedge Gate, Globe and Check Valves 50 mm and Smaller for the Petroleum, Petrochemical and
Allied Industries.
EEMUA 144 - 90/10 Copper Nickel Alloy Piping for Offshore Applications. Tubes Seamless and Welded.
EEMUA 145 - 90/10 Copper Nickel Alloy Piping for Offshore Applications. Flanges Composite and Solid.
EEMUA 146 - 90/10 Copper Nickel Alloy Piping for Offshore Applications. Fittings.
ISO 3834-2 – Quality requirements for fusion welding of metallic materials-part 2: comprehensive quality requirements.
ISO 15156 - Petroleum and natural gas industries: Materials for use in H2S - containing environments in oil and gas
production.
ISO 14692- Petroleum and natural gas industries: Glass-reinforced plastic (GRP) piping.
ISO 17292 - Metal ball valves for petroleum, petrochemical and allied industries.
ISO 21457- Petroleum, petrochemical and natural gas industries – Material selection and corrosion control for oil and
gas production systems.
ISO 27509- Petroleum and natural gas industries: Compact Flanged connections with IX seal ring (First Edition).
MSS SP-6 - Standard Finishes for Contact Faces de Pipe Flanges and Connecting-End Flanges of Valves and
Fittings.
MSS SP-70 - Cast Iron Gate Valves, Flanged and Threaded Ends.
MSS SP-71 - Gray Iron Swing Check Valves, Flanged and Threaded Ends.
MSS SP-72 - Ball Valves with Flanged or Butt-Welding Ends for General Service.
MSS SP-97 – Integrally Reinforced Forged Branch Outlet Fittings – Socket Welding, Threaded, and Buttwelding Ends.
NBR 15827 - Industrial Valves for Installations of Exploration, Production, Refining and Transport of Petroleum
Products - Requirements for Design and Prototype Test.
- Rev. 11 - Page 6 of 21
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
BE Beveled Ends
BF Butt Strap
BS Bell Spigot
CL Class
Cr Chrome
CS Carbon Steel
CuNi Copper-Nickel
EJ Elastic Joint
FLG Flange
FF Flat Face
GALV Galvanized
GR Grade
HC Half Coupling
HEX Hexagonal
IN Inch
MAX Maximum
- Rev. 11 - Page 7 of 21
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
PE Plain Ends
PTFE Polytetrafluoroethylene
RF Raised Face
RJ Rigid Joint
SCH Schedule
SDL Saddle
SML Seamless
SOC Sockolet
SS Stainless Steel
STD Standard
SW Socket Weld
TEE Tee
THD Threaded
- Rev. 11 - Page 8 of 21
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
WOL Weldolet
XS Extra Strong
WLD Welded
WN Weld Neck
WOL Weldolet
- Rev. 11 - Page 9 of 21
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
A–B–C–D–E
A – Nominal Pipe Size
Non-Integer Nominal Pipe Sizes shall be written as Fractions using a dash (“–”) to separate the integer part from
the fraction, if necessary. Example: 1/2, 3/4, 1-1/2, 2-1/2.
The number/fraction shall be followed by the double prime symbol (”) representative of inch unit, never two (’)
prime symbols.
E – Insulation:
PP – Personal Protection
HC – Heat Conservation
CC – Cold Conservation
NI – Not Insulated (Absence of insulation shall always be represented by “NI”)
Note: Piperun tag shall not contain any spaces between characteres
1–1/2”–P–B10–0010–HC
Nominal Pipe Size: 1 1/2 inch
Service: P - Process
B–D
For 3D modelling, where Pipeline tagging is also required, it shall consist only of Service and sequential. Additional
information regarding nominal pipe size, specification and insulation shall be associated with the piperun. Example of
pipeline tag:
P–0010
Service: Process (non-corrosive Hydrocarbon)
Sequential Numbering: 0010
- Rev. 11 - Page 10 of 21
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
Other
Carbon Steel API 5L, 6,4mm 17 Code Z
chracteristics
RPVC 25
Inconel cladded Alloy Steel Aço Liga 9Ni ASTM A 333 Gr8 33
- Rev. 11 - Page 11 of 21
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
BG Inert Gas B1, B3, B10, C10, E10, F10, G10, R3B, R3C, R9B, R9C, S3B, S3C, S9B, S9C
CHW Chilled Water B1, B10, B20, R9B, R9C, S9B, S9C
Chemical Injection (non-
CI corrosive) B1, B10, C10, E10, F10, G10, S9B, S9C, T12, T3,
DA Open Drain B22, B23, B25, B9, R9B, R9C, S9B, S9C
Closed Drain (Non-Corrosive
DF hydrocarbon) B1, B10
F Safety System and Flare B10, B12, B16, B19, B3, B30, B50, B6, B9, C3, C6
FG Fuel Gas B10, B19, B3, B6, C10, C3, E10, E3, E6, F10, F3, G3
G Glycol B10, B3, B6, C10, C3, C6, E10, E3, E6, F10, F3, G10, G3, G6, H6
H Hydraulic Fluid B3, C3, E3, F3, G3, H3, S3B, S3C
- Rev. 11 - Page 12 of 21
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
IG Instrumentation Gas B3
IW De-Aerated Sea Water Injection B1, B10, B14, B23, C10, C14, C30, E10, E14, F10, F14, G10, G14, H12, H30
JF Helicopter Refueling B3
Process (non-corrosive B10, B6, C10, C10P, C6, E10, E3, E6, F10, F10P, F3, F6, G10, G10P, G3, G6, H10,
P hydrocarbon) H10P, H10R, H12, H12P, H3, H31, H6, J10, J12, J12P, J31, J31P, J40, J40P
B11, B12, B16, B17, B19, B3, B30, B9, C12, C16, C19, C3, C30, C9, E16, E17, E19,
PC Process (Corrosive Hydrocarbon) E3, E30, E32, E9, F16, F3, F30, F32, G12, G12P, G16, G16P, G19, G3, H12, H12P,
H16, H3, H30, H30P, H31, H33, J12, J12P, J40, J40P
PCW Produced water B11, B12, B25, B26, C11, C12, C30, E11, F11, G11, H11
PWH Hot Fresh Water B21, B22, B23, B3, S3B, S3C
W Industrial water B1, B10, B20, B22, B23, B3, C10, E10, F10, G10, H10, R9B, R9C, S9B, S9C
- Rev. 11 - Page 13 of 21
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
B7 I 20 bar - 0 75 Copper-Nickel FL FW
- Rev. 11 - Page 14 of 21
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
- Rev. 11 - Page 15 of 21
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
- Rev. 11 - Page 16 of 21
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
S7 A 20 bar - 0 75 Copper-Nickel FW
- Rev. 11 - Page 17 of 21
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
Accommodations B20H
DF Non corrosive Closed Drain All System (in the hull) B10H
- Rev. 11 - Page 18 of 21
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
Accommodations B20H
Accommodation B20H
PW Potable Water
Other Lines B3H
- Rev. 11 - Page 19 of 21
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
Accommodation B21H
PWH Hot Fresh Water
Other Lines B3H
- Rev. 11 - Page 20 of 21
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
BG CHW CV D DA DF FG OL PLD SN SP
B10H A 150 1.6 mm 0 100 Carbon Steel
STA W TR PCG
Tubing
T3H A - - 60 60 CI CNI
SS316/316L
- Rev. 11 - Page 21 of 21
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
2"
Pipe S-40S -
T-323 2 ½" BE ASME B36.10/B36.19 ASTM A358 Type 316/316L Cl 1 or 3 WLD
3" - 24"
90 Elbow C01-43
45 Elbow C02-43
Tee C03-43
ASME B16.11
Cross C05-43 ½" - 1 ½"
Coupling C06-43 - 3000 SW
ASTM A182 Gr F316/316L
Cap C11-43
Sockolet C55-43 MSS SP-97
Red Tee C04-43
¾" - 1 ½" ASME B16.11
Red Coupling C08-43
Weldolet C12-43 BE MSS SP-97
90 LR Elbow C15-44 -
45 LR Elbow C16-44
90 SR Elbow C17-44 2"
ASME B16.9 ASTM A403 Gr WP316/316L
Tee C20-44
BE
Cap C22-44
Fittings
Cross C24-44
Weldolet C12-43 MSS SP-97 ASTM A182 Gr F316/316L
90 LR Elbow C15-44 -
45 LR Elbow C16-44
90 SR Elbow C17-44 2 ½"
ASME B16.9 ASTM A403 Gr WP316/316L
Tee C20-44
According to pipe - BE
Cap C22-44
Cross C24-44
Weldolet C12-43 3" - 10" MSS SP-97 ASTM A182 Gr F316/316L
90 LR Elbow C15-44 -
45 LR Elbow C16-44
90 SR Elbow C17-44
Conc. Red C18-44
Ecc. Red C19-44 3" - 24" ASME B16.9 ASTM A403 Gr WP316/316L
BE
Tee C20-44
Red Tee C21-44
Cap C22-44
Cross C24-44
Straight Nipple N-S145 ½" - 1 ½" ASTM A733 ASTM A312 TP316/316L
PBE
N-C144 ¾" - 1 ½"
Nipple
Spiral-Wound J-150-EH 2 ½" - Class 150 Raised Face ASME B16.20 AISI 316/graphite
3" - 24"
A193 B7, Zn-Ni
Nuts
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
51 For temperatures abov e 60°C, stainless steels shall be coated acc. to I-ET-3010.00-1200-956-P4X-002 - General Painting.
113 See table on item 8 for piping spec selection according to serv ice and application.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 1.6 mm
3" - 4"
According to pipe - MSS SP-95 ASTM A234 Gr WPB
N-E303 ¾" - 1 ½" TBE
Swage Ecc Nipple 2"
N-E503 BLE x TSE
3" - 4"
Threaded (THD) F-150-A2 ½" - 1 ½"
Flanges
Flat type J-150-CA 1" - 24" - Class 150 Flat Face ASME B16.21 Aramid/NBR
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
45 This Spec is only applicable for onshore units.
79 Use w elding neck flanges w hen directly connected to buttw elding fittings.
92 Threaded connections must be w eld sealed in case of v ibration.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 1.6 mm
16" - 18"
Pipe T-102 - ASME B36.10
20" 0.281" BE API 5L Gr B PSL 1 WLD (HFW or SAW)
24" 0.312"
26" - 28" S-10
30" - 32" 0.344" API 5L Gr B PSL 1 WLD SAW
34" - 36" STD
90 Elbow C01-02
45 Elbow C02-02
Tee C03-02
ASME B16.11
Cross C05-02 ½" - 1 ½"
Coupling C06-02 - 3000 SW
ASTM A105
Cap C11-02
Sockolet C55-02 MSS SP-97
Red Tee C04-02
¾" - 1 ½" ASME B16.11
Fittings
2" - 24"
Welding Neck (WN) F-150-K2
26" - 36" According to pipe Class 150 Raised Face ASME B16.47 A ASTM A105
½" - 24" ASME B16.5
Blind F-150-L2
26" - 36" ASME B16.47 A
Bolts & Gasket
Spiral-Wound J-150-EH ½" - 36" - Class 150 Raised Face ASME B16.20 AISI 316/graphite
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
43 The FL serv ice is only applicable for onshore units.
115 Gaskets shall not be be used to assembly butterfly v alv es API 609 category A, unless required required by the v alv e manufacturer.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
S-40S
Pipe 2" - 24" -
T-323 BE ASME B36.10/B36.19 ASTM A358 Type 316/316L Cl 1 or 3 WLD
26" - 40" 0.375"
90 Elbow C01-43
45 Elbow C02-43
Tee C03-43
ASME B16.11
Cross C05-43 ½" - 1 ½"
Coupling C06-43 - 3000 SW
ASTM A182 Gr F316/316L
Cap C11-43
Sockolet C55-43 MSS SP-97
Red Tee C04-43
¾" - 1 ½" ASME B16.11
Fittings
Spiral-Wound J-150-EH ½" - 40" - Class 150 Raised Face ASME B16.20 AISI 316/graphite
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
38 Stub in connections according to ASME B31.3 may be used only for flare sy stem.
47 Diesel serv ice "D" is only applicable for piping dow nstream the centrifuge.
51 For temperatures abov e 60°C, stainless steels shall be coated acc. to I-ET-3010.00-1200-956-P4X-002 - General Painting.
54 This spec for PC serv ice should only be used w hen recommended in annex D.
55 This spec for FG serv ice is applicable for piping dow nstream the filters.
57 All standardized pipe w all thickness listed in DR-ENGP-I-1.1 are calculated considering only internal pressure. Other loads resulting of the piping analy sis (supporting, flex ibility , fadigue) may
increase minimum required thickness.
59 In case of use this spec below -30 °C, the material shall be furnished w ith solution heat treatment.
62 This spec for Amine serv ice is applicable for piping dow nstream the Amine stripper up to booster pump suction.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
127 ISO 6162-1/2 flanges may be used only for H - Hy draulic Fluid.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
2"
Pipe S-40S -
T-323 2 ½" BE ASME B36.10/B36.19 ASTM A358 Type 316/316L Cl 1 or 3 WLD
3" - 24"
90 Elbow C01-43
45 Elbow C02-43
Tee C03-43
ASME B16.11
Cross C05-43 ½" - 1 ½"
Coupling C06-43 - 3000 SW
ASTM A182 Gr F316/316L
Cap C11-43
Sockolet C55-43 MSS SP-97
Red Tee C04-43
¾" - 1 ½" ASME B16.11
Red Coupling C08-43
Weldolet C12-43 BE MSS SP-97
90 LR Elbow C15-44 -
45 LR Elbow C16-44
90 SR Elbow C17-44 2"
ASME B16.9 ASTM A403 Gr WP316/316L
Tee C20-44
BE
Cap C22-44
Fittings
Cross C24-44
Weldolet C12-43 MSS SP-97 ASTM A182 Gr F316/316L
90 LR Elbow C15-44 -
45 LR Elbow C16-44
90 SR Elbow C17-44 2 ½"
ASME B16.9 ASTM A403 Gr WP316/316L
Tee C20-44
According to pipe - BE
Cap C22-44
Cross C24-44
Weldolet C12-43 3" - 10" MSS SP-97 ASTM A182 Gr F316/316L
90 LR Elbow C15-44 -
45 LR Elbow C16-44
90 SR Elbow C17-44
Conc. Red C18-44
Ecc. Red C19-44 3" - 24" ASME B16.9 ASTM A403 Gr WP316/316L
BE
Tee C20-44
Red Tee C21-44
Cap C22-44
Cross C24-44
Straight Nipple N-S145 ½" - 1 ½" ASTM A733 ASTM A312 TP316/316L
PBE
N-C144 ¾" - 1 ½"
Nipple
Spiral-Wound J-150-EH 2 ½" - Class 150 Raised Face ASME B16.20 AISI 316/graphite
3" - 24"
A193 B7, Zn-Ni
Nuts
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
38 Stub in connections according to ASME B31.3 may be used only for flare sy stem.
51 For temperatures abov e 60°C, stainless steels shall be coated acc. to I-ET-3010.00-1200-956-P4X-002 - General Painting.
59 In case of use this spec below -30 °C, the material shall be furnished w ith solution heat treatment.
113 See table on item 8 for piping spec selection according to serv ice and application.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
127 ISO 6162-1/2 flanges may be used only for H - Hy draulic Fluid.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 1.6 mm
SAW)
Pipe T-102 14" - ASME B36.10
S-10 BE
16" - 18"
20" 0.281" API 5L Gr B PSL 1 WLD (HFW or SAW)
24" 0.312"
90 Elbow C01-02
45 Elbow C02-02
Tee C03-02
ASME B16.11
Cross C05-02 ½" - 1 ½"
Coupling C06-02 - 3000 SW
ASTM A105
Cap C11-02
Sockolet C55-02 MSS SP-97
Red Tee C04-02
¾" - 1 ½" ASME B16.11
Fittings
Spiral-Wound J-150-EH ½" - 24" - Class 150 Raised Face ASME B16.20 AISI 316/graphite
A193 B7
Nuts
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 3.2 mm
Pipe T-102 3" - 6" STD - ASME B36.10 API 5L Gr B PSL 1 (SML or WLD HFW or WLD
BE SAW)
8" - 10" S-20
12" 0.281"
Sockolet C55-02 ¾" - 3000 SW
MSS SP-97 ASTM A105
Weldolet C12-02 2" - 4" BE
90 LR Elbow C15-03 -
45 LR Elbow C16-03
Fittings
90 SR Elbow C17-03
2" - 12"
Tee C20-03
According to pipe -
Cap C22-03 ASME B16.9 ASTM A234 Gr WPB
BE
Cross C24-03
Conc. Red C18-03
Ecc. Red C19-03 3" - 12"
Red Tee C21-03
¾"
Bolts & Gasket Flanges
Flat type J-150-PA 2" - 12" - Class 150 Raised Face ASME B16.21 Aramid/NBR
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
SOC - Sockolet
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 1.6 mm
2" - 24"
Welding Neck (WN) F-150-K3
26" - 36" According to pipe Class 150 Raised Face ASME B16.47 A ASTM A350 Gr LF2 Class 1
½" - 24" ASME B16.5
Blind F-150-L3
26" - 36" ASME B16.47 A
Bolts & Gasket
Spiral-Wound J-150-EH ½" - 36" - Class 150 Raised Face ASME B16.20 AISI 316/graphite
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
25 Charpy impact test is required at the minimum temperature of this spec, according to ASME B31.3 and standard material specification.
38 Stub in connections according to ASME B31.3 may be used only for flare sy stem.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
12" 7.0mm
Pipe T-202 - EEMUA 234
14" 8.0mm
BE
16" 9.0mm
18" 9.5mm
20" 11.0mm
24" 13.0mm
Cu-Ni 90/10 (UNS C70620) WLD
28" 15.0mm
32" 17.0mm
36" 19.0mm
90 Elbow C01-35
45 Elbow C02-35
Fcap
Tee C03-35
Coupling C06-35
Plug C09-35 ½" - 1 ½" 20 bar THD
Union C10-35
- Fcap
Cap C11-35
Connector C37-35
-
Connector Union C38-35
Sockolet C55-35 ½" - 2" - Cap
Fittings
Mcap x Fcap
Red Coupling C08-35 EEMUA 234 Cu-Ni 90/10 (UNS C70620)
¾" - 1 ½" 20 bar Fcap
Bush C23-35 FTHD x Mcap
Weldolet C12-35 2" - 16" BE
90 LR Elbow C15-35 -
45 LR Elbow C16-35
2" - 36"
Tee C20-35 According to pipe
-
Cap C22-35
Conc. Red C18-35 BE
Ecc. Red C19-35 3" - 36"
Red Tee C21-35
Stub End WN-L C39-35 4" - 36" - 20 bar
N-A335 TBE
Nipple
Connector Nipple N-A735 ¾" - 1 ½" According to pipe - FTHD x Fcap EEMUA 234 Cu-Ni 90/10 (UNS C70620)
N-A835 MTHD x Fcap
Slip on (SO) F-20-HM ½" - 1 ½" 20 bar 17293 Cu-Ni 90/10 (UNS 70620)
Bolts & Gasket Flanges
Flat type J-150-P4 ½" - 36" - Class 150 Raised Face ASME B16.21 Compressed sheet, fire-tested
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
53 This spec must be used only for offshore facilities.
86 Pipes in this spec do not take account additional thickness for threads. Must be ev aluated pipes thicker than these here specified if threaded pipe w ill be applied.
87 Piping, connections and flanges should be specified according EEMUA 144/145/146.
104 The backing flange and stub ends are part of the composite flange according EEMUA 234.
110 Epox y coating for flanges shall be applied according to I-ET-3010.00-1200-956-P4X-002 - General Painting.
115 Gaskets shall not be be used to assembly butterfly v alv es API 609 category A, unless required required by the v alv e manufacturer.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
126 Thermal spray application shall be according to the requirements of I-ET-3010.00-1200-956-P4X-003. Consumable specification: AWS C2.25m: W-CuAl-1 or ISO 14919: CuAl10.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
12" 7.0mm
Pipe T-202 - EEMUA 234
14" 8.0mm
BE
16" 9.0mm
18" 9.5mm
20" 11.0mm
24" 13.0mm
Cu-Ni 90/10 (UNS C70620) WLD
28" 15.0mm
32" 17.0mm
36" 19.0mm
90 Elbow C01-35
45 Elbow C02-35
Fcap
Tee C03-35
Coupling C06-35
Plug C09-35 ½" - 1 ½" 20 bar THD
Union C10-35
- Fcap
Cap C11-35
Connector C37-35
-
Connector Union C38-35
Sockolet C55-35 ½" - 2" - Cap
Fittings
Mcap x Fcap
Red Coupling C08-35 EEMUA 234 Cu-Ni 90/10 (UNS C70620)
¾" - 1 ½" 20 bar Fcap
Bush C23-35 FTHD x Mcap
Weldolet C12-35 2" - 16" BE
90 LR Elbow C15-35 -
45 LR Elbow C16-35
2" - 36"
Tee C20-35 According to pipe
-
Cap C22-35
Conc. Red C18-35 BE
Ecc. Red C19-35 3" - 36"
Red Tee C21-35
Stub End WN-L C39-35 4" - 36" - 20 bar
N-A335 TBE
Nipple
Connector Nipple N-A735 ¾" - 1 ½" According to pipe - FTHD x Fcap EEMUA 234 Cu-Ni 90/10 (UNS C70620)
N-A835 MTHD x Fcap
Slip on (SO) F-20-HM ½" - 1 ½" 20 bar 17293 Cu-Ni 90/10 (UNS 70620)
Bolts & Gasket Flanges
Flat type J-150-P4 ½" - 36" - Class 150 Raised Face ASME B16.21 Compressed sheet, fire-tested
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
53 This spec must be used only for offshore facilities.
86 Pipes in this spec do not take account additional thickness for threads. Must be ev aluated pipes thicker than these here specified if threaded pipe w ill be applied.
87 Piping, connections and flanges should be specified according EEMUA 144/145/146.
104 The backing flange and stub ends are part of the composite flange according EEMUA 234.
110 Epox y coating for flanges shall be applied according to I-ET-3010.00-1200-956-P4X-002 - General Painting.
113 See table on item 8 for piping spec selection according to serv ice and application.
115 Gaskets shall not be be used to assembly butterfly v alv es API 609 category A, unless required required by the v alv e manufacturer.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
126 Thermal spray application shall be according to the requirements of I-ET-3010.00-1200-956-P4X-003. Consumable specification: AWS C2.25m: W-CuAl-1 or ISO 14919: CuAl10.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
12" 5.5mm
Pipe T-202 - EEMUA 234
14" 6.5mm
BE
16" 7.0mm
18" 8.0mm
20" 8.5mm
24" 10.5mm
Cu-Ni 90/10 (UNS C70620) WLD
28" 12.0mm
32" 13.5mm
36" 15.5mm
90 Elbow C01-35
45 Elbow C02-35
Fcap
Tee C03-35
Coupling C06-35
Plug C09-35 ½" - 1 ½" 20 bar THD
Union C10-35
- Fcap
Cap C11-35
Connector C37-35
-
Connector Union C38-35
Sockolet C55-35 ½" - 2" - Cap
Fittings
Fcap
Red Coupling C08-35 ¾" - 1 ½" 20 bar EEMUA 234 Cu-Ni 90/10 (UNS C70620)
Mcap x Fcap
Weldolet C12-35 2" - 16" BE
90 LR Elbow C15-35 -
45 LR Elbow C16-35
2" - 36"
Tee C20-35
According to pipe -
Cap C22-35
Conc. Red C18-35
BE
Ecc. Red C19-35 3" - 36"
Red Tee C21-35
4" 20 bar
Stub End WN-L C39-35 -
6" - 36" 16 bar
N-A335 TBE
Nipple
Connector Nipple N-A735 ¾" - 1 ½" According to pipe - FTHD x Fcap EEMUA 234 Cu-Ni 90/10 (UNS C70620)
N-A835 MTHD x Fcap
Slip on (SO) F-20-HM ½" - 1 ½" 20 bar 17293 Cu-Ni 90/10 (UNS 70620)
Bolts & Gasket Flanges
Flat type J-150-P4 ½" - 36" - Class 150 Raised Face ASME B16.21 Compressed sheet, fire-tested
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
53 This spec must be used only for offshore facilities.
86 Pipes in this spec do not take account additional thickness for threads. Must be ev aluated pipes thicker than these here specified if threaded pipe w ill be applied.
87 Piping, connections and flanges should be specified according EEMUA 144/145/146.
94 This spec for SW serv ice is applicable only for Nav al Sy stem, for generators and inert gas seal.
104 The backing flange and stub ends are part of the composite flange according EEMUA 234.
110 Epox y coating for flanges shall be applied according to I-ET-3010.00-1200-956-P4X-002 - General Painting.
115 Gaskets shall not be be used to assembly butterfly v alv es API 609 category A, unless required required by the v alv e manufacturer.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
126 Thermal spray application shall be according to the requirements of I-ET-3010.00-1200-956-P4X-003. Consumable specification: AWS C2.25m: W-CuAl-1 or ISO 14919: CuAl10.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
Cross C24-03
Weldolet C12-02 MSS SP-97 ASTM A105
90 LR Elbow C15-03 -
45 LR Elbow C16-03
90 SR Elbow C17-03 2 ½"
ASME B16.9 ASTM A234 Gr WPB
Tee C20-03
According to pipe - BE
Cap C22-03
Cross C24-03
Weldolet C12-02 3" - 10" MSS SP-97 ASTM A105
90 LR Elbow C15-03 -
45 LR Elbow C16-03
90 SR Elbow C17-03
Conc. Red C18-03
Ecc. Red C19-03 3" - 24" ASME B16.9 ASTM A234 Gr WPB
BE
Tee C20-03
Red Tee C21-03
Cap C22-03
Cross C24-03
Straight Nipple N-S120 ½" - 1 ½" ASTM A733 API 5L Gr B PSL 1 seamless
PBE
N-C103 ¾" - 1 ½"
Nipple
Flat type J-150-PA 2 ½" - Class 150 Raised Face ASME B16.21 Aramid/NBR
3" - 24"
A193 B7, Zn-Ni
Nuts
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
52 Piping, fittings and acessories must be galv anized after spool fabrication according to ASTM A123 w ith minimum coating thickness of100µm.
113 See table on item 8 for piping spec selection according to serv ice and application.
115 Gaskets shall not be be used to assembly butterfly v alv es API 609 category A, unless required required by the v alv e manufacturer.
121 For Venting application shall be applied thicker piping S-80 up to NPS 8.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 3.2 mm
14"
Pipe T-102 S-20 - ASME B36.10
16" - 18" BE
API 5L Gr B PSL 1 WLD (HFW or SAW)
20" - 24"
STD
26" - 28"
30" - 32" 0.406"
API 5L Gr B PSL 1 WLD SAW
34" 0.438"
36" 0.469"
90 Elbow C01-02
45 Elbow C02-02
Tee C03-02
ASME B16.11
Cross C05-02 ½" - 1 ½"
Coupling C06-02 - 6000 SW
ASTM A105
Cap C11-02
Sockolet C55-02 MSS SP-97
Red Tee C04-02
¾" - 1 ½" ASME B16.11
Fittings
2" - 24"
Welding Neck (WN) F-150-K2
26" - 36" According to pipe Class 150 Raised Face ASME B16.47 A ASTM A105
½" - 24" ASME B16.5
Blind F-150-L2
26" - 36" ASME B16.47 A
Bolts & Gasket
Spiral-Wound J-150-EH ½" - 36" - Class 150 Raised Face ASME B16.20 AISI 316/graphite
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
54 This spec for PC serv ice should only be used w hen recommended in annex D.
62 This spec for Amine serv ice is applicable for piping dow nstream the Amine stripper up to booster pump suction.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 3.2 mm
Spiral-Wound J-150-EH ½" - 24" - Class 150 Raised Face ASME B16.20 AISI 316/graphite
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
113 See table on item 8 for piping spec selection according to serv ice and application.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 1.6 mm
16" - 18"
Pipe T-102 - ASME B36.10
20" 0.281" BE API 5L Gr B PSL 1 WLD (HFW or SAW)
24" 0.312"
26" - 28" S-10
30" - 32" 0.344" API 5L Gr B PSL 1 WLD SAW
34" - 36" STD
90 Elbow C01-02
45 Elbow C02-02
Tee C03-02
ASME B16.11
Cross C05-02 ½" - 1 ½"
Coupling C06-02 - 6000 SW
ASTM A105
Cap C11-02
Sockolet C55-02 MSS SP-97
Red Tee C04-02
¾" - 1 ½" ASME B16.11
Fittings
2" - 24"
Welding Neck (WN) F-150-K2
26" - 36" According to pipe Class 150 Raised Face ASME B16.47 A ASTM A105
½" - 24" ASME B16.5
Blind F-150-L2
26" - 36" ASME B16.47 A
Bolts & Gasket
Spiral-Wound J-150-EH ½" - 36" - Class 150 Raised Face ASME B16.20 AISI 316/graphite
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
38 Stub in connections according to ASME B31.3 may be used only for flare sy stem.
40 The IW serv ice is only applicable for onshore units.
43 The FL serv ice is only applicable for onshore units.
46 Diesel serv ice "D" is only applicable for piping upstream the centrifuge.
56 This spec for FG serv ice is applicable for piping upstream the filters.
64 This spec for Amine serv ice is applicable for piping dow nstream the regeneration unit and upstream the contactor unit.
115 Gaskets shall not be be used to assembly butterfly v alv es API 609 category A, unless required required by the v alv e manufacturer.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 1.6 mm
STD SAW)
Pipe T-102 3" - 8" - ASME B36.10
BE
10" - 14"
16" - 24" XS API 5L Gr B PSL 1 WLD (HFW or SAW)
26" - 36" API 5L Gr B PSL 1 WLD SAW
90 Elbow C01-02
45 Elbow C02-02
Tee C03-02
ASME B16.11
Cross C05-02 ½" - 1 ½"
Coupling C06-02 - 6000 SW
ASTM A105
Cap C11-02
Sockolet C55-02 MSS SP-97
Red Tee C04-02
¾" - 1 ½" ASME B16.11
Red Coupling C08-02
Weldolet C12-02 1" - 2" BE MSS SP-97
90 LR Elbow C15-03 -
45 LR Elbow C16-03
90 SR Elbow C17-03
2" ASME B16.9 ASTM A234 Gr WPB
Tee C20-03
BE
Cap C22-03
Cross C24-03
Weldolet C12-02 MSS SP-97 ASTM A105
Fittings
90 LR Elbow C15-03 -
45 LR Elbow C16-03
90 SR Elbow C17-03
Conc. Red C18-03
2 ½"
Ecc. Red C19-03 ASME B16.9 ASTM A234 Gr WPB
Tee C20-03 According to pipe - BE
Red Tee C21-03
Cap C22-03
Cross C24-03
Weldolet C12-02 3" - 16" MSS SP-97 ASTM A105
90 LR Elbow C15-03 -
45 LR Elbow C16-03
90 SR Elbow C17-03
Conc. Red C18-03
Ecc. Red C19-03 3" - 36" ASME B16.9 ASTM A234 Gr WPB
BE
Tee C20-03
Red Tee C21-03
Cap C22-03
Cross C24-03
Straight Nipple N-S120 ½" - 1 ½" ASTM A733 API 5L Gr B PSL 1 seamless
PBE
N-C103 ¾" - 1 ½"
Nipple
Spiral-Wound J-150-EH 2 ½" - Class 150 Raised Face ASME B16.20 AISI 316/graphite
3" - 36"
A193 B7, Zn-Ni
Nuts
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
46 Diesel serv ice "D" is only applicable for piping upstream the centrifuge.
56 This spec for FG serv ice is applicable for piping upstream the filters.
113 See table on item 8 for piping spec selection according to serv ice and application.
115 Gaskets shall not be be used to assembly butterfly v alv es API 609 category A, unless required required by the v alv e manufacturer.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
121 For Venting application shall be applied thicker piping S-80 up to NPS 8.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
1" - 28"
Tee C20-03
According to pipe -
Cap C22-03 ASME B16.9 ASTM A234 Gr WPB
BE
Cross C24-03
Conc. Red C18-03
Ecc. Red C19-03 1 ½" - 28"
Red Tee C21-03
Swage Conc Nipple N-C203
Bolts & Gasket Flanges Nipple
1 ½" - 4" According to pipe - BBE MSS SP-95 ASTM A234 Gr WPB
Swage Ecc Nipple N-E203
1" - 24" ASME B16.5
Welding Neck (WN) F-150-K2
26" - 28" ASME B16.47 A
According to pipe Class 150 Raised Face ASTM A105
1" - 24" ASME B16.5
Blind F-150-L2
26" - 28" ASME B16.47 A
Flat type J-150-PC 1" - 28" - Class 150 Raised Face ASME B16.21 Multidirectional Expanded PTFE
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
50 Piping, fittings and acessories shall be organic coated internally acc. to I-ET-3010.00-1200-956-P4X-002 - General Painting.
54 This spec for PC serv ice should only be used w hen recommended in annex D.
115 Gaskets shall not be be used to assembly butterfly v alv es API 609 category A, unless required required by the v alv e manufacturer.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
1" - 36"
Tee C20-03
According to pipe -
Cap C22-03 ASME B16.9 ASTM A234 Gr WPB
BE
Cross C24-03
Conc. Red C18-03
Ecc. Red C19-03 1 ½" - 36"
Red Tee C21-03
Swage Conc Nipple N-C203
Bolts & Gasket Flanges Nipple
1 ½" - 4" According to pipe - BBE MSS SP-95 ASTM A234 Gr WPB
Swage Ecc Nipple N-E203
1" - 24" ASME B16.5
Welding Neck (WN) F-150-K2
26" - 36" ASME B16.47 A
According to pipe Class 150 Raised Face ASTM A105
1" - 24" ASME B16.5
Blind F-150-L2
26" - 36" ASME B16.47 A
Flat type J-150-PC 1" - 36" - Class 150 Raised Face ASME B16.21 Multidirectional Expanded PTFE
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
50 Piping, fittings and acessories shall be organic coated internally acc. to I-ET-3010.00-1200-956-P4X-002 - General Painting.
113 See table on item 8 for piping spec selection according to serv ice and application.
115 Gaskets shall not be be used to assembly butterfly v alv es API 609 category A, unless required required by the v alv e manufacturer.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
1"
Weldolet C12-30 BE MSS SP-97
2" - 16"
90 LR Elbow C15-32 -
45 LR Elbow C16-32
90 SR Elbow C17-32
2" - 36"
Tee C20-32 According to pipe -
Cap C22-32 ASME B16.9 ASTM A815 (UNS S32760)
BE
Cross C24-32
Conc. Red C18-32
Ecc. Red C19-32 3" - 36"
Red Tee C21-32
Straight Nipple N-S131 ½" - 1 ½" ASTM A733 ASTM A790 (UNS S32760)
PBE
N-C132 ¾" - 1 ½"
Nipple
2" - 24"
Welding Neck (WN) F-150-KH
26" - 36" According to pipe Class 150 Raised Face ASME B16.47 A ASTM A182 Gr F55
½" - 24" ASME B16.5
Blind F-150-LH
26" - 36" ASME B16.47 A
Bolts & Gasket
Spiral-Wound J-150-EL ½" - 36" - Class 150 Raised Face ASME B16.20 Duplex/graphite
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
26 See Annex A for v alv e casting qualification requirements.
48 For temperatures abov e110°C, Superduplex shall be coated acc. to I-ET-3010.00-1200-956-P4X-002 - General Painting.
54 This spec for PC serv ice should only be used w hen recommended in annex D.
57 All standardized pipe w all thickness listed in DR-ENGP-I-1.1 are calculated considering only internal pressure. Other loads resulting of the piping analy sis (supporting, flex ibility , fadigue) may
increase minimum required thickness.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
122 Inspection of pipe and piping components shall follow ASTM A923 requirements.
123 The application of this pipe specification for PCW - Produced Water is conditioned to max imum ox y gen content 20 ppb and max temperature 120ºC.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
1" - 44"
Tee C20-03
According to pipe -
Cap C22-03 ASME B16.9 ASTM A234 Gr WPB
BE
Cross C24-03
Conc. Red C18-03
Ecc. Red C19-03 1 ½" - 44"
Red Tee C21-03
Swage Conc Nipple N-C203
Bolts & Gasket Flanges Nipple
1 ½" - 4" According to pipe - BBE MSS SP-95 ASTM A234 Gr WPB
Swage Ecc Nipple N-E203
1" - 24" ASME B16.5
Welding Neck (WN) F-150-D2
26" - 44" ASME B16.47 A
According to pipe Class 150 Flat Face ASTM A105
1" - 24" ASME B16.5
Blind F-150-E2
26" - 44" ASME B16.47 A
Flat type J-150-CC 1" - 44" - Class 150 Flat Face ASME B16.21 Multidirectional Expanded PTFE
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
28 The IW serv ice is only applicable for offshore units.
50 Piping, fittings and acessories shall be organic coated internally acc. to I-ET-3010.00-1200-956-P4X-002 - General Painting.
115 Gaskets shall not be be used to assembly butterfly v alv es API 609 category A, unless required required by the v alv e manufacturer.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
STD SAW)
Pipe T-102 3" - 8" - ASME B36.10
BE
10" - 14"
16" - 24" XS API 5L Gr B PSL 1 WLD (HFW or SAW)
26" - 36" API 5L Gr B PSL 1 WLD SAW
Weldolet C12-02 BE MSS SP-97 ASTM A105
90 LR Elbow C15-03 -
45 LR Elbow C16-03
90 SR Elbow C17-03 1" - 2"
Tee C20-03
Cap C22-03 ASME B16.9 ASTM A234 Gr WPB
Cross C24-03 BE
Conc. Red C18-03
Ecc. Red C19-03 1 ½" - 2"
Red Tee C21-03
Weldolet C12-02 MSS SP-97 ASTM A105
90 LR Elbow C15-03 -
45 LR Elbow C16-03
90 SR Elbow C17-03
Fittings
1 ½" - 4" According to pipe - BBE MSS SP-95 ASTM A234 Gr WPB
Swage Ecc Nipple N-E203
1" - 24" ASME B16.5
Welding Neck (WN) F-150-D2
26" - 36" ASME B16.47 A
Flanges
1" - 2"
According to pipe Class 150 Flat Face ASTM A105
2 ½" ASME B16.5
Blind F-150-E2
3" - 24"
26" - 36" ASME B16.47 A
1" - 2"
Bolts & Gasket
Flat type J-150-CC 2 ½" - Class 150 Flat Face ASME B16.21 Multidirectional Expanded PTFE
3" - 36"
A193 B7, Zn-Ni
Nuts
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
50 Piping, fittings and acessories shall be organic coated internally acc. to I-ET-3010.00-1200-956-P4X-002 - General Painting.
113 See table on item 8 for piping spec selection according to serv ice and application.
115 Gaskets shall not be be used to assembly butterfly v alv es API 609 category A, unless required required by the v alv e manufacturer.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 6 mm
Tee C20-48
Cap C22-48 According to pipe - JIS B2313 / ASME B16.9 Mariloy S-400 (JIS G3454/57)
BE
Cross C24-48
Conc. Red C18-48
Ecc. Red C19-48 6" - 36"
Red Tee C21-48
2 ½"
Slip on (SO) F-150-H2 ASME B16.5
3" - 24"
Flanges
Flat type J-150-P4 - Class 150 Raised Face ASME B16.21 Compressed sheet, fire-tested
3" - 36"
A193 B7, Zn-Ni
Nuts
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
113 See table on item 8 for piping spec selection according to serv ice and application.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
128 Branch table filled w ith "note" shall be stub-in ty pe w ith carbon steel (A516 Gr 60) reinforcement pad.
129 For piping <= NPS 3 shall be used B14H spec.
130 Welding consumable shall follow the recommendation of NIPPON Steel. Cov ered arc w elding ectrode: RS-55. Flux cored w elding w ire: SF-55RS. Gas metal arc w elding w ire: YM-55RSA. Gas
tungsten arc w elding rod: YT-55RS.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
2" - 24"
Welding Neck (WN) F-150-KG
26" - 34" According to pipe Class 150 Raised Face ASME B16.47 A ASTM A182 Gr F51
½" - 24" ASME B16.5
Blind F-150-LG
26" - 34" ASME B16.47 A
Bolts & Gasket
Spiral-Wound J-150-EL ½" - 34" - Class 150 Raised Face ASME B16.20 Duplex/graphite
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
26 See Annex A for v alv e casting qualification requirements.
29 For temperatures abov e 100°C, Duplex shall be coated acc. to I-ET-3010.00-1200-956-P4X-002 - General Painting.
54 This spec for PC serv ice should only be used w hen recommended in annex D.
57 All standardized pipe w all thickness listed in DR-ENGP-I-1.1 are calculated considering only internal pressure. Other loads resulting of the piping analy sis (supporting, flex ibility , fadigue) may
increase minimum required thickness.
60 This spec for Amine serv ice is applicable for piping upstream the Amine Regeneration unit.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
122 Inspection of pipe and piping components shall follow ASTM A923 requirements.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
2" - 24"
Welding Neck (WN) F-150-KG
26" - 32" According to pipe Class 150 Raised Face ASME B16.47 A ASTM A182 Gr F51
½" - 24" ASME B16.5
Blind F-150-LG
26" - 32" ASME B16.47 A
Bolts & Gasket
Spiral-Wound J-150-EL ½" - 32" - Class 150 Raised Face ASME B16.20 Duplex/graphite
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
26 See Annex A for v alv e casting qualification requirements.
29 For temperatures abov e 100°C, Duplex shall be coated acc. to I-ET-3010.00-1200-956-P4X-002 - General Painting.
54 This spec for PC serv ice should only be used w hen recommended in annex D.
57 All standardized pipe w all thickness listed in DR-ENGP-I-1.1 are calculated considering only internal pressure. Other loads resulting of the piping analy sis (supporting, flex ibility , fadigue) may
increase minimum required thickness.
60 This spec for Amine serv ice is applicable for piping upstream the Amine Regeneration unit.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
122 Inspection of pipe and piping components shall follow ASTM A923 requirements.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 6.4 mm
Pipe T-102 6" 0.344" - ASME B36.10 API 5L Gr B PSL 1 (SML or WLD HFW or WLD
BE SAW)
8" S-60
10" 0.438"
12" - 14" S-40
Sockolet C55-02 ½" - 1 ½" MSS SP-97
90 Elbow C01-02
45 Elbow C02-02
Tee C03-02 - 9000 SW
¾" - 1 ½" ASME B16.11
Cross C05-02
Coupling C06-02 ASTM A105
Cap C11-02
Weldolet C12-02 1" According to pipe - BE MSS SP-97
Red Tee C04-02
Fittings
Spiral-Wound J-150-EH ¾" - 14" - Class 150 Raised Face ASME B16.20 AISI 316/graphite
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
1" - 36"
Tee C20-03
According to pipe -
Cap C22-03 ASME B16.9 ASTM A234 Gr WPB
BE
Cross C24-03
Conc. Red C18-03
Ecc. Red C19-03 1 ½" - 36"
Red Tee C21-03
1 ½" - 2"
Swage Conc Nipple N-C203
Nipple
3" - 4"
According to pipe - BBE MSS SP-95 ASTM A234 Gr WPB
1 ½" - 2"
Swage Ecc Nipple N-E203
3" - 4"
1" - 24" ASME B16.5
Bolts & Gasket Flanges
Flat type J-150-CC 1" - 36" - Class 150 Flat Face ASME B16.21 Multidirectional Expanded PTFE
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
50 Piping, fittings and acessories shall be organic coated internally acc. to I-ET-3010.00-1200-956-P4X-002 - General Painting.
113 See table on item 8 for piping spec selection according to serv ice and application.
115 Gaskets shall not be be used to assembly butterfly v alv es API 609 category A, unless required required by the v alv e manufacturer.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 3.2 mm
S-10
Pipe 16" - ASME B36.10
BE
18" - 20" 0.281"
24" 0.312"
T-106 ASTM A671 Gr CC60 Class 22 WLD
26" S-10
28" - 30" 0.344"
32" - 36" STD
90 Elbow C01-04
45 Elbow C02-04
Tee C03-04
ASME B16.11
Cross C05-04 ½" - 1 ½"
Coupling C06-04 - 6000 SW
ASTM A350 Gr LF2 Cl 1
Cap C11-04
Sockolet C55-04 MSS SP-97
Red Tee C04-04
¾" - 1 ½" ASME B16.11
Fittings
2" - 24"
Welding Neck (WN) F-150-K3
26" - 36" According to pipe Class 150 Raised Face ASME B16.47 A ASTM A350 Gr LF2 Class 1
½" - 24" ASME B16.5
Blind F-150-L3
26" - 36" ASME B16.47 A
Bolts & Gasket
Spiral-Wound J-150-EH ½" - 36" - Class 150 Raised Face ASME B16.20 AISI 316/graphite
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
25 Charpy impact test is required at the minimum temperature of this spec, according to ASME B31.3 and standard material specification.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP - -
Pipe T-401 ½" - 8" S-80 - PE ASTM D1785 PVC - ASTM D1785 class 1120 SML
-
90 Elbow C01-50
- PVC - ASTM D1784 class 12454
45 Elbow C02-50
Socket
Tee C03-50 ½" - 8" ASTM D2467
Coupling C06-50
Cap C11-50
Red Tee C21-50 According to pipe
¾" - 8"
Red. Bushing C56-50 - -
Bolts & Gasket Flanges Nipple
Straight Nipple N-S150 ½" - 8" According to pipe - PBE ASTM D1785 PVC - ASTM D1785 class 1120
Flat type J-150-CC ½" - 8" - Class 150 Flat Face ASME B16.21 Multidirectional Expanded PTFE
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
SOC - Sockolet
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
36 Plain w ashers must be used to assembly flanged connections.
61 The pressure rating is reduced in 50%, in case of use threaded fittings.
75 The use of this spec is restricted to inside liv ing quarter modules and out of classified areas.
90 FRP v alv es in this spec are indicated for isolation of the sodium hy poclorite generation unit.
105 Whenev er non-mettalics v alv es are used, the spec´s pressure-temperature limits may be reduced according annex A (item A.7.6.2).
111 The flanges dimensions are according to ASME B16.5.
119 When not informed, header to branch connection shall be according to manufacturer recommendation.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP - -
Pipe T-401 ½" - 8" S-80 - PE ASTM D1785 PVC - ASTM D1785 class 1120 SML
-
90 Elbow C01-50
- PVC - ASTM D1784 class 12454
45 Elbow C02-50
Socket
Tee C03-50 ½" - 8" ASTM D2467
Coupling C06-50
Cap C11-50
Red Tee C21-50 According to pipe
¾" - 8"
Red. Bushing C56-50 - -
Bolts & Gasket Flanges Nipple
Straight Nipple N-S150 ½" - 8" According to pipe - PBE ASTM D1785 PVC - ASTM D1785 class 1120
Flat type J-150-CC ½" - 8" - Class 150 Flat Face ASME B16.21 Multidirectional Expanded PTFE
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
SOC - Sockolet
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
36 Plain w ashers must be used to assembly flanged connections.
61 The pressure rating is reduced in 50%, in case of use threaded fittings.
75 The use of this spec is restricted to inside liv ing quarter modules and out of classified areas.
90 FRP v alv es in this spec are indicated for isolation of the sodium hy poclorite generation unit.
105 Whenev er non-mettalics v alv es are used, the spec´s pressure-temperature limits may be reduced according annex A (item A.7.6.2).
111 The flanges dimensions are according to ASME B16.5.
113 See table on item 8 for piping spec selection according to serv ice and application.
119 When not informed, header to branch connection shall be according to manufacturer recommendation.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
Pipe T-402 ½" - 8" S-80 - PE ASTM F441 CPVC - Chlorinated polyvinyl chloride, ASTM
F441 4120 SML
Plug C09-51
THD
Cap C11-51 ½" - 2"
Connector C37-51 -
Union C10-51 ½" - 4"
45 Tee C48-51 ½" - 6"
Fittings
-
90 Elbow C01-51
- ASTM F439 CPVC - ASTM D1784 class 23447
45 Elbow C02-51
Socket
Tee C03-51 ½" - 8"
Coupling C06-51
Cap C11-51
Red Tee C21-51 According to pipe
¾" - 8"
Red. Bushing C56-51 - -
Bolts & Gasket Flanges Nipple
Straight Nipple N-S151 ½" - 8" According to pipe - PBE ASTM F441 CPVC - ASTM F441 class 4120
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
SOC - Sockolet
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
36 Plain w ashers must be used to assembly flanged connections.
61 The pressure rating is reduced in 50%, in case of use threaded fittings.
75 The use of this spec is restricted to inside liv ing quarter modules and out of classified areas.
105 Whenev er non-mettalics v alv es are used, the spec´s pressure-temperature limits may be reduced according annex A (item A.7.6.2).
111 The flanges dimensions are according to ASME B16.5.
119 When not informed, header to branch connection shall be according to manufacturer recommendation.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
Pipe T-402 ½" - 8" S-80 - PE ASTM F441 CPVC - Chlorinated polyvinyl chloride, ASTM
F441 4120 SML
Plug C09-51
THD
Cap C11-51 ½" - 2"
Connector C37-51 -
Union C10-51 ½" - 4"
45 Tee C48-51 ½" - 6"
Fittings
-
90 Elbow C01-51
- ASTM F439 CPVC - ASTM D1784 class 23447
45 Elbow C02-51
Socket
Tee C03-51 ½" - 8"
Coupling C06-51
Cap C11-51
Red Tee C21-51 According to pipe
¾" - 8"
Red. Bushing C56-51 - -
Bolts & Gasket Flanges Nipple
Straight Nipple N-S151 ½" - 8" According to pipe - PBE ASTM F441 CPVC - ASTM F441 class 4120
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
SOC - Sockolet
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
36 Plain w ashers must be used to assembly flanged connections.
61 The pressure rating is reduced in 50%, in case of use threaded fittings.
75 The use of this spec is restricted to inside liv ing quarter modules and out of classified areas.
105 Whenev er non-mettalics v alv es are used, the spec´s pressure-temperature limits may be reduced according annex A (item A.7.6.2).
111 The flanges dimensions are according to ASME B16.5.
113 See table on item 8 for piping spec selection according to serv ice and application.
119 When not informed, header to branch connection shall be according to manufacturer recommendation.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
Pipe T-404 1" - 40" acc. manufact. - ISO 14692 fiberglass type E or E-CR. Design pressure 10
Bell-Spigot bar@90ºC. SML
Plug C09-36 250 THD ASME B16.15 ASTM B62 (UNS C83600)
1" - 1 ½"
Thd Saddle C52-52
- - -
Flg Saddle C51-52 1" - 6"
Coupling C06-52 Bell-Spigot
90 LR Elbow C15-52 -
Bell-Spigot
45 LR Elbow C16-52 1" - 40"
Fittings
Flat type J-150-C3 1" - 40" - Class 150 Flat Face ASME B16.21 Neoprene
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
31 Electrical conductiv ity /resistiv ity shall be tested in accordance w ith ASTM D257. For components requiring electrical conductiv ity due to ex ternal charge generating mechanisms, the surface
resistiv ity shall be 10^5 ohms or less. For components requiring electrical conductiv ity due to internal charge generating mechanisms, the v olume resistiv ity shall be 10^3 ohm-meter or less.
32 GRP piping and fittings must be certified according to lev el L3 IMO A753 fire endurance test.
33 GRP piping and fittings must be supplied w ith UV protection.
34 GRP piping and fittings must hav e Ty pe Approv al certified by Classification Societies.
35 Pipes and fittings must be supplied by the same manufacturer, that also shall be responsable for design, fabrication, assembly , inspection, test, repair and comissioning.
36 Plain w ashers must be used to assembly flanged connections.
37 See Annex H for Minimum Requirements for FRP pipes and fittings.
39 The bolt torque limit shall be informed by manufacturer.
74 Bell-spigot adhesiv ed joint is allow able for all diameter in open drain (DA) serv ice, but the max imum pressure shall be 4 bar.
105 Whenev er non-mettalics v alv es are used, the spec´s pressure-temperature limits may be reduced according annex A (item A.7.6.2).
112 For pipes and fittings may be used as alternativ e v iny l ester resins. See Annex H.
115 Gaskets shall not be be used to assembly butterfly v alv es API 609 category A, unless required required by the v alv e manufacturer.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
Pipe T-406 1" - 46" acc. manufact. - ISO 14692 fiberglass type E or E-CR. Design pressure 16
Bell-Spigot bar@90ºC. SML
Plug C09-36 250 THD ASME B16.15 ASTM B62 (UNS C83600)
1" - 1 ½"
Thd Saddle C52-54 -
- -
Flg Saddle C51-54 1" - 6"
Bell-Spigot
45 LR Elbow C16-54 According to pipe
1" - 32" Butt-Strap
FRP Stub End C64-54
-
Bell-Spigot
Coupling C06-54
90 LR Elbow C15-54 -
1" - 46"
According to pipe Bell-Spigot
Tee C20-54
Butt-Strap
FRP Conc. Red. C61-54
Bell-Spigot
FRP Ecc. Red. C62-54 2" - 46" -
Butt-Strap
Fittings
Blind F-16-LT 1" - 46" 10004 fiberglass type E or E-CR. Suitable for 90°C.
According to pipe 16 bar Raised Face
Backing Flange F-16-YV 1" - 44" Drilling acc. B16.5/B16.47 ASTM A105 Epoxy coated
CL150
Flat type J-150-P3 1" - 46" - Class 150 Raised Face ASME B16.21 Neoprene
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
31 Electrical conductiv ity /resistiv ity shall be tested in accordance w ith ASTM D257. For components requiring electrical conductiv ity due to ex ternal charge generating mechanisms, the surface
resistiv ity shall be 10^5 ohms or less. For components requiring electrical conductiv ity due to internal charge generating mechanisms, the v olume resistiv ity shall be 10^3 ohm-meter or less.
32 GRP piping and fittings must be certified according to lev el L3 IMO A753 fire endurance test.
33 GRP piping and fittings must be supplied w ith UV protection.
34 GRP piping and fittings must hav e Ty pe Approv al certified by Classification Societies.
35 Pipes and fittings must be supplied by the same manufacturer, that also shall be responsable for design, fabrication, assembly , inspection, test, repair and comissioning.
36 Plain w ashers must be used to assembly flanged connections.
37 See Annex H for Minimum Requirements for FRP pipes and fittings.
39 The bolt torque limit shall be informed by manufacturer.
105 Whenev er non-mettalics v alv es are used, the spec´s pressure-temperature limits may be reduced according annex A (item A.7.6.2).
112 For pipes and fittings may be used as alternativ e v iny l ester resins. See Annex H.
115 Gaskets shall not be be used to assembly butterfly v alv es API 609 category A, unless required required by the v alv e manufacturer.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
Pipe T-406 1" - 44" acc. manufact. - ISO 14692 fiberglass type E or E-CR. Design pressure 16
Bell-Spigot bar@90ºC. SML
Plug C09-36 1" - 1 ½" 250 THD ASME B16.15 ASTM B62 (UNS C83600)
Flg Saddle C51-54 -
1" - 6" - -
Thd Saddle C52-54
Bell-Spigot
45 LR Elbow C16-54 1" - 32" According to pipe
Butt-Strap
Coupling C06-54 - Bell-Spigot
90 LR Elbow C15-54 -
1" - 44"
According to pipe Butt-Strap
Tee C20-54
Bell-Spigot
Butt-Strap
FRP Conc. Red. C61-54
Fittings
Bell-Spigot
Butt-Strap FRP - Bisphenol A Epoxy resins reinforced with
FRP Ecc. Red. C62-54 2" - 44" - ISO 14692 fiberglass type E or E-CR. Design pressure
16 bar Bell-Spigot 16bar@90ºC
Red Tee C63-54
Butt-Strap
Bell-Spigot
34"
Butt-Strap
Bell-Spigot
36"
Butt-Strap
45 LR Elbow C16-54 According to pipe
Bell-Spigot
38"
Butt-Strap
Bell-Spigot
40" - 44"
Butt-Strap
Bolts & Gasket Flanges
Flat type J-150-C3 1" - 44" - Class 150 Flat Face ASME B16.21 Neoprene
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
31 Electrical conductiv ity /resistiv ity shall be tested in accordance w ith ASTM D257. For components requiring electrical conductiv ity due to ex ternal charge generating mechanisms, the surface
resistiv ity shall be 10^5 ohms or less. For components requiring electrical conductiv ity due to internal charge generating mechanisms, the v olume resistiv ity shall be 10^3 ohm-meter or less.
32 GRP piping and fittings must be certified according to lev el L3 IMO A753 fire endurance test.
33 GRP piping and fittings must be supplied w ith UV protection.
34 GRP piping and fittings must hav e Ty pe Approv al certified by Classification Societies.
35 Pipes and fittings must be supplied by the same manufacturer, that also shall be responsable for design, fabrication, assembly , inspection, test, repair and comissioning.
36 Plain w ashers must be used to assembly flanged connections.
37 See Annex H for Minimum Requirements for FRP pipes and fittings.
39 The bolt torque limit shall be informed by manufacturer.
105 Whenev er non-mettalics v alv es are used, the spec´s pressure-temperature limits may be reduced according annex A (item A.7.6.2).
112 For pipes and fittings may be used as alternativ e v iny l ester resins. See Annex H.
115 Gaskets shall not be be used to assembly butterfly v alv es API 609 category A, unless required required by the v alv e manufacturer.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
Pipe T-408 1" - 16" acc. manufact. - Butt-Strap ISO 14692 fiberglass type E or E-CR. Design pressure 16
bar@120ºC. SML
Plug C09-36 250 THD ASME B16.15 ASTM B62 (UNS C83600)
1" - 1 ½"
Thd Saddle C52-56 -
-
Flg Saddle C51-56 1" - 2" -
90 LR Elbow C15-56
45 LR Elbow C16-56 According to pipe
1" - 16"
Tee C20-56
Fittings
FRP Stub End C64-56 16 bar FRP - Bisphenol A Epoxy resins reinforced with
Butt-Strap
FRP Conc. Red. C61-56 ISO 14692 fiberglass type E or E-CR. Design pressure
FRP Ecc. Red. C62-56 2" 16bar@120ºC
Red Tee C63-56
-
Flg Saddle C51-56 3" - 6" - -
FRP Conc. Red. C61-56
FRP Ecc. Red. C62-56 3" - 16" 16 bar Butt-Strap
Red Tee C63-56
FRP - Bisphenol A Epoxy resins reinforced with
Bolts & Gasket Flanges
Blind F-16-EU Flat Face 10004 fiberglass type E or E-CR. Suitable for 120°C.
1" - 16" According to pipe 16 bar
Backing Flange F-16-YV Raised Face Drilling acc. B16.5/B16.47 ASTM A105 Epoxy coated
CL150
Flat type J-150-CC 1" - 16" - Class 150 Flat Face ASME B16.21 Multidirectional Expanded PTFE
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
30 This spec shall be used only in fix ed offshore units.
31 Electrical conductiv ity /resistiv ity shall be tested in accordance w ith ASTM D257. For components requiring electrical conductiv ity due to ex ternal charge generating mechanisms, the surface
resistiv ity shall be 10^5 ohms or less. For components requiring electrical conductiv ity due to internal charge generating mechanisms, the v olume resistiv ity shall be 10^3 ohm-meter or less.
32 GRP piping and fittings must be certified according to lev el L3 IMO A753 fire endurance test.
33 GRP piping and fittings must be supplied w ith UV protection.
34 GRP piping and fittings must hav e Ty pe Approv al certified by Classification Societies.
35 Pipes and fittings must be supplied by the same manufacturer, that also shall be responsable for design, fabrication, assembly , inspection, test, repair and comissioning.
36 Plain w ashers must be used to assembly flanged connections.
37 See Annex H for Minimum Requirements for FRP pipes and fittings.
39 The bolt torque limit shall be informed by manufacturer.
66 It´s not allow ed to use ov erw rap joints (adhesiv e joint cov ered by fiber-resin lay ers).
69 The fire ring main shall be kept permanently full and installed in areas beneath w hich there is no possibility of combustible material accumulation.
105 Whenev er non-mettalics v alv es are used, the spec´s pressure-temperature limits may be reduced according annex A (item A.7.6.2).
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
C49-60 EJ/BS
- according to manufacturer RPVC - Glass fiber reinforced PVC
C50-58 RJ/BS
11°15' SR Elb C50-59 RJ/SS
C50-60 EJ/BS
C18-58 RJ/BS
Conc. Red C18-59 RJ/SS
C18-60 EJ/BS
C19-58 RJ/BS
Ecc. Red C19-59 According to pipe - RJ/SS
C19-60 EJ/BS
1 ½" - 28"
C21-58 RJ/BS
Red Tee C21-59 RJ/SS
C21-60 EJ/BS
C53-58 RJ/BS
Red Cross C53-59 - 16 bar RJ/SS
C53-60 EJ/BS
1" - 24" ASME B16.5
Bolts & Gasket Flanges
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
36 Plain w ashers must be used to assembly flanged connections.
39 The bolt torque limit shall be informed by manufacturer.
45 This Spec is only applicable for onshore units.
105 Whenev er non-mettalics v alv es are used, the spec´s pressure-temperature limits may be reduced according annex A (item A.7.6.2).
115 Gaskets shall not be be used to assembly butterfly v alv es API 609 category A, unless required required by the v alv e manufacturer.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
Pipe T-408 1" - 36" acc. manufact. - ISO 14692 fiberglass type E or E-CR. Design pressure 16
Bell-Spigot bar@120ºC. SML
Plug C09-36 250 THD ASME B16.15 ASTM B62 (UNS C83600)
1" - 1 ½"
Thd Saddle C52-56
- -
Flg Saddle C51-56 1" - 6"
-
Bell-Spigot
FRP Stub End C64-56 1" - 32"
Butt-Strap
Coupling C06-56 Bell-Spigot
90 LR Elbow C15-56 -
Butt-Strap
45 LR Elbow C16-56 1" - 36"
According to pipe Bell-Spigot
Fittings
Butt-Strap
Tee C20-56 FRP - Bisphenol A Epoxy resins reinforced with
Bell-Spigot
ISO 14692 fiberglass type E or E-CR. Design pressure
Butt-Strap 16bar@120ºC
FRP Conc. Red. C61-56 16 bar
Bell-Spigot
FRP Ecc. Red. C62-56 2" - 36"
Butt-Strap
Red Tee C63-56 -
Bell-Spigot
34"
Butt-Strap
FRP Stub End C64-56
Bell-Spigot
36"
Butt-Strap
FRP - Bisphenol A Epoxy resins reinforced with
Bolts & Gasket Flanges
Blind F-16-EU Flat Face 10004 fiberglass type E or E-CR. Suitable for 120°C.
1" - 36" According to pipe 16 bar
Backing Flange F-16-YV Raised Face Drilling acc. B16.5/B16.47 ASTM A105 Epoxy coated
CL150
Flat type J-150-PC 1" - 36" - Class 150 Raised Face ASME B16.21 Multidirectional Expanded PTFE
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
31 Electrical conductiv ity /resistiv ity shall be tested in accordance w ith ASTM D257. For components requiring electrical conductiv ity due to ex ternal charge generating mechanisms, the surface
resistiv ity shall be 10^5 ohms or less. For components requiring electrical conductiv ity due to internal charge generating mechanisms, the v olume resistiv ity shall be 10^3 ohm-meter or less.
32 GRP piping and fittings must be certified according to lev el L3 IMO A753 fire endurance test.
33 GRP piping and fittings must be supplied w ith UV protection.
34 GRP piping and fittings must hav e Ty pe Approv al certified by Classification Societies.
35 Pipes and fittings must be supplied by the same manufacturer, that also shall be responsable for design, fabrication, assembly , inspection, test, repair and comissioning.
36 Plain w ashers must be used to assembly flanged connections.
37 See Annex H for Minimum Requirements for FRP pipes and fittings.
39 The bolt torque limit shall be informed by manufacturer.
66 It´s not allow ed to use ov erw rap joints (adhesiv e joint cov ered by fiber-resin lay ers).
105 Whenev er non-mettalics v alv es are used, the spec´s pressure-temperature limits may be reduced according annex A (item A.7.6.2).
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
Pipe T-409 1" - 6" acc. manufact. - ISO 14692 brominated) reinforced with fiberglass type E-CR,
Butt-Strap inner liner with fiberglass veils type C. Design
pressure 16 bar@85ºC. SML
Thd Saddle C52-57 1" - 1 ½"
- -
Flg Saddle C51-57 1" - 4" -
Coupling C06-57 Bell-Spigot
90 LR Elbow C15-57 -
Butt-Strap
45 LR Elbow C16-57 1" - 6"
According to pipe FRP - Epoxy vinylester resins (bisphenol A or
Fittings
Bell-Spigot
Tee C20-57 ISO 14692 brominated) reinforced with fiberglass type E-CR,
Butt-Strap inner liner with fiberglass veils type C. Design
16 bar pressure 16bar@85ºC
Bell-Spigot
Red Tee C63-57 2" - 3"
Butt-Strap
FRP Conc. Red. C61-57 -
Bell-Spigot
2" - 6"
Butt-Strap
FRP Ecc. Red. C62-57
Bell-Spigot
Bolts & Gasket Flanges
Flat type J-150-CC 1" - 6" - Class 150 Flat Face ASME B16.21 Multidirectional Expanded PTFE
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
HC - Half Coupling
SOC - Sockolet
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
31 Electrical conductiv ity /resistiv ity shall be tested in accordance w ith ASTM D257. For components requiring electrical conductiv ity due to ex ternal charge generating mechanisms, the surface
resistiv ity shall be 10^5 ohms or less. For components requiring electrical conductiv ity due to internal charge generating mechanisms, the v olume resistiv ity shall be 10^3 ohm-meter or less.
32 GRP piping and fittings must be certified according to lev el L3 IMO A753 fire endurance test.
33 GRP piping and fittings must be supplied w ith UV protection.
34 GRP piping and fittings must hav e Ty pe Approv al certified by Classification Societies.
35 Pipes and fittings must be supplied by the same manufacturer, that also shall be responsable for design, fabrication, assembly , inspection, test, repair and comissioning.
36 Plain w ashers must be used to assembly flanged connections.
37 See Annex H for Minimum Requirements for FRP pipes and fittings.
39 The bolt torque limit shall be informed by manufacturer.
66 It´s not allow ed to use ov erw rap joints (adhesiv e joint cov ered by fiber-resin lay ers).
105 Whenev er non-mettalics v alv es are used, the spec´s pressure-temperature limits may be reduced according annex A (item A.7.6.2).
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
14"
Pipe S-10 -
16" - 18" BE
T-102 ASME B36.10
20" 0.281" API 5L Gr B PSL 1 WLD (HFW or SAW)
24" 0.312"
26" - 28" S-10
API 5L Gr B PSL 1 WLD SAW
30" 0.344"
90 Elbow C01-33
45 Elbow C02-33
Tee C03-33
ASME B16.11
Cross C05-33 ½" - 1 ½"
Coupling C06-33 - 3000 SW
Cap C11-33
Sockolet C55-33 MSS SP-97
Red Tee C04-33
¾" - 1 ½" ASME B16.11 ASTM B366 (UNS N06625)
Red Coupling C08-33
Weldolet C12-33 BE MSS SP-97
90 LR Elbow C15-33 -
45 LR Elbow C16-33
90 SR Elbow C17-33 2" - 3"
ASME B16.9
Fittings
Tee C20-33
Cap C22-33
Cross C24-33 BE
Weldolet C12-02 2" - 14" MSS SP-97 ASTM A105
Conc. Red C18-33
Ecc. Red C19-33 3" - 4" ASTM B366 (UNS N06625)
According to pipe -
Red Tee C21-33
90 LR Elbow C15-03 -
45 LR Elbow C16-03
90 SR Elbow C17-03
4" - 30" ASME B16.9
Tee C20-03
Cap C22-03 ASTM A234 Gr WPB
BE
Cross C24-03
Conc. Red C18-03
Ecc. Red C19-03 6" - 30"
Red Tee C21-03
Straight Nipple N-S139 ½" - 1 ½" ASTM A733 ASTM B444 Gr 1 (UNS N06625)
PBE
N-C133 ¾" - 1 ½"
Nipple
Spiral-Wound J-150-EM ½" - 30" - Class 150 Raised Face ASME B16.20 Inconel/graphite
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
27 See Annex D to check the piping spec range application for H2S and CO2 serv ice.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
Straight Nipple N-S141 ½" - 1 ½" According to pipe - PBE ASTM A733 ASTM A312 TP310H
2" - 24"
Welding Neck (WN) F-300-KW
26" - 56" According to pipe Class 300 Raised Face ASME B16.47 A ASTM A182 Gr F310H
½" - 24" ASME B16.5
Blind F-300-LW
26" - 56" ASME B16.47 A
Bolts & Gasket
Spiral-Wound J-300-E2 ½" - 56" - Class 300 Raised Face ASME B16.20 AISI 316/MICA (high temp.)
Nuts
Stud and Nuts P-300-10 ½" - 1 ¾" - - - ASME B1.1 A453 660
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
TEE - Tee
HC - Half Coupling
SOC - Sockolet
0.5 TEE
0.75 RTEE TEE
1 RTEE RTEE TEE
1.5 RTEE RTEE RTEE TEE
2 SOC SOC SOC SOC TEE
3 SOC SOC SOC SOC RTEE TEE
4 SOC SOC SOC SOC RTEE RTEE TEE
6 SOC SOC SOC SOC WOL RTEE RTEE TEE
8 SOC SOC SOC SOC WOL WOL RTEE RTEE TEE
10 SOC SOC SOC SOC WOL WOL WOL RTEE RTEE TEE
12 SOC SOC SOC SOC WOL WOL WOL RTEE RTEE RTEE TEE
14 SOC SOC SOC SOC WOL WOL WOL WOL RTEE RTEE RTEE TEE
16 SOC SOC SOC SOC WOL WOL WOL WOL RTEE RTEE RTEE RTEE TEE
18 SOC SOC SOC SOC WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE TEE
20 SOC SOC SOC SOC WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE TEE
24 SOC SOC SOC SOC WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE TEE
26 SOC SOC SOC SOC WOL WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE TEE
28 SOC SOC SOC SOC WOL WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE RTEE TEE
30 SOC SOC SOC SOC WOL WOL WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE RTEE TEE
32 SOC SOC SOC SOC WOL WOL WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE
34 SOC SOC SOC SOC WOL WOL WOL WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE
36 SOC SOC SOC SOC WOL WOL WOL WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE
38 SOC SOC SOC SOC WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE
40 SOC SOC SOC SOC WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE
42 SOC SOC SOC SOC WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE
44 SOC SOC SOC SOC WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE
46 SOC SOC SOC SOC WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE
48 SOC SOC SOC SOC WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE
52 SOC SOC SOC SOC WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE
54 SOC SOC SOC SOC WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE
56 SOC SOC SOC SOC WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL WOL RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE TEE
0.5 0.75 1 1.5 2 3 4 6 8 10 12 14 16 18 20 24 26 28 30 32 34 36 38 40 42 44 46 48 52 54 56
BRANCH SIZE
Notes
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
51 For temperatures abov e 60°C, stainless steels shall be coated acc. to I-ET-3010.00-1200-956-P4X-002 - General Painting.
117 The flange assembly shall be done w ith tw o nuts and one w asher per bolt side. Circular w asher shall be according to ASTM F436.
118 The spec is limited for application abov e flare serv ice platform.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
Spiral-Wound J-300-EH ½" - 30" - Class 300 Raised Face ASME B16.20 AISI 316/graphite
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
51 For temperatures abov e 60°C, stainless steels shall be coated acc. to I-ET-3010.00-1200-956-P4X-002 - General Painting.
55 This spec for FG serv ice is applicable for piping dow nstream the filters.
67 Branches w ith diameter greater than or equal to half the nominal diameter of the pipe shall be fitted w ith guide bars according to DR-ENGP-I-1.14 – Standard Specification for Design of Pig L/R
68 This Spec shall be applied for distribution sy stem of CO2, after directional v alv es.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
127 ISO 6162-1/2 flanges may be used only for H - Hy draulic Fluid.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
Pipe S-40S -
T-323 2" - 12" BE ASME B36.10/B36.19 ASTM A358 Type 316/316L Cl 1 or 3 WLD
90 Elbow C01-43
45 Elbow C02-43
Tee C03-43
ASME B16.11
Cross C05-43 ½" - 1 ½"
Coupling C06-43 - 3000 SW
ASTM A182 Gr F316/316L
Cap C11-43
Sockolet C55-43 MSS SP-97
Red Tee C04-43
¾" - 1 ½" ASME B16.11
Fittings
Spiral-Wound J-300-EH ½" - 12" - Class 300 Raised Face ASME B16.20 AISI 316/graphite
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
51 For temperatures abov e 60°C, stainless steels shall be coated acc. to I-ET-3010.00-1200-956-P4X-002 - General Painting.
113 See table on item 8 for piping spec selection according to serv ice and application.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
127 ISO 6162-1/2 flanges may be used only for H - Hy draulic Fluid.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 1.6 mm
Spiral-Wound J-300-EH ½" - 24" - Class 300 Raised Face ASME B16.20 AISI 316/graphite
A193 B7
Nuts
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 3.2 mm
2" - 3" XS
Pipe T-102 - ASME B36.10 API 5L Gr B PSL 1 (SML or WLD HFW or WLD
4" 0.250" BE SAW)
6" 0.312"
Sockolet C55-02 ¾" - 1 ½" - 3000 SW
MSS SP-97 ASTM A105
Weldolet C12-02 2" BE
90 LR Elbow C15-03 -
45 LR Elbow C16-03
Fittings
90 SR Elbow C17-03
2" - 6"
Tee C20-03
According to pipe -
Cap C22-03 ASME B16.9 ASTM A234 Gr WPB
BE
Cross C24-03
Conc. Red C18-03
Ecc. Red C19-03 3" - 6"
Red Tee C21-03
Bolts & Gasket Flanges Nipple
Straight Nipple N-S120 ¾" According to pipe - PBE ASTM A733 API 5L Gr B PSL 1 seamless
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
HC - Half Coupling
SOC - Sockolet
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 1.6 mm
Spiral-Wound J-300-EH ½" - 24" - Class 300 Raised Face ASME B16.20 AISI 316/graphite
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
25 Charpy impact test is required at the minimum temperature of this spec, according to ASME B31.3 and standard material specification.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
Pipe T-102 2" - 6" STD - ASME B36.10 API 5L Gr B PSL 1 (SML or WLD HFW or WLD
BE SAW)
8" S-20
90 Elbow C01-02
45 Elbow C02-02
Tee C03-02
Cross C05-02 ASME B16.11
½" - 1 ½"
Coupling C06-02
- 3000 SW
Union C10-02 ASTM A105
Cap C11-02
Sockolet C55-02 MSS SP-97
Red Tee C04-02
Fittings
Flat type J-300-PA ½" - 8" - Class 300 Raised Face ASME B16.21 Aramid/NBR
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
SOC - Sockolet
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
52 Piping, fittings and acessories must be galv anized after spool fabrication according to ASTM A123 w ith minimum coating thickness of100µm.
63 From -18°C to 0°C, API 5L gr B shall be furnished normalized.
68 This Spec shall be applied for distribution sy stem of CO2, after directional v alv es.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
Pipe T-102 2" - 6" STD - ASME B36.10 API 5L Gr B PSL 1 (SML or WLD HFW or WLD
BE SAW)
8" S-20
45 Elbow C02-02
Tee C03-02
Cross C05-02
ASME B16.11
Coupling C06-02 ½" - 1 ½"
Union C10-02
- 3000 SW
Cap C11-02 ASTM A105
Sockolet C55-02 MSS SP-97
Red Tee C04-02
¾" - 1 ½"
Red Coupling C08-02 ASME B16.11
Fittings
Flat type J-300-PA ½" - 8" - Class 300 Raised Face ASME B16.21 Aramid/NBR
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
SOC - Sockolet
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
52 Piping, fittings and acessories must be galv anized after spool fabrication according to ASTM A123 w ith minimum coating thickness of100µm.
63 From -18°C to 0°C, API 5L gr B shall be furnished normalized.
68 This Spec shall be applied for distribution sy stem of CO2, after directional v alv es.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 3.2 mm
2" - 24"
Welding Neck (WN) F-300-K2
26" - 32" According to pipe Class 300 Raised Face ASME B16.47 A ASTM A105
½" - 24" ASME B16.5
Blind F-300-L2
26" - 32" ASME B16.47 A
Bolts & Gasket
Spiral-Wound J-300-EH ½" - 32" - Class 300 Raised Face ASME B16.20 AISI 316/graphite
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
11 For API 5L pipe the max imum carbon equiv alent is CE iiw = 0,43% or CE pcm = 0,25%.
27 See Annex D to check the piping spec range application for H2S and CO2 serv ice.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 1.6 mm
18" XS
Pipe T-102 - ASME B36.10 API 5L Gr B PSL 1 WLD (HFW or SAW)
20" 0.562" BE
24" S-40
26" 0.625"
28" 0.688" API 5L Gr B PSL 1 WLD SAW
30" - 32" 0.750"
90 Elbow C01-02
45 Elbow C02-02
Tee C03-02
ASME B16.11
Cross C05-02 ½" - 1 ½"
Coupling C06-02 - 6000 SW
ASTM A105
Cap C11-02
Sockolet C55-02 MSS SP-97
Red Tee C04-02
¾" - 1 ½" ASME B16.11
Fittings
2" - 24"
Welding Neck (WN) F-300-K2
26" - 32" According to pipe Class 300 Raised Face ASME B16.47 A ASTM A105
½" - 24" ASME B16.5
Blind F-300-L2
26" - 32" ASME B16.47 A
Bolts & Gasket
Spiral-Wound J-300-EH ½" - 32" - Class 300 Raised Face ASME B16.20 AISI 316/graphite
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
40 The IW serv ice is only applicable for onshore units.
46 Diesel serv ice "D" is only applicable for piping upstream the centrifuge.
56 This spec for FG serv ice is applicable for piping upstream the filters.
83 This spec for Amine serv ice is applicable for booster pump discharge.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 1.6 mm
Spiral-Wound J-300-EH ½" - 24" - Class 300 Raised Face ASME B16.20 AISI 316/graphite
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
46 Diesel serv ice "D" is only applicable for piping upstream the centrifuge.
113 See table on item 8 for piping spec selection according to serv ice and application.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.8 1.6 mm
SAW)
Pipe T-102 10" - 14" STD - ASME B36.10
BE
16" 0.406"
18" - 20" XS API 5L Gr B PSL 1 WLD (HFW or SAW)
24" 0.625"
90 Elbow C01-02
45 Elbow C02-02
Tee C03-02
ASME B16.11
Cross C05-02 ½" - 1 ½"
Coupling C06-02 - 6000 SW ASTM A105
Cap C11-02
Sockolet C55-02 MSS SP-97
Red Tee C04-02
¾" - 1 ½" ASME B16.11
Red Coupling C08-02
90 LR Elbow C15-03 -
Fittings
45 LR Elbow C16-03
2" - 3" ASME B16.9 ASTM A234 Gr WPB
90 SR Elbow C17-03
Cross C24-03
Weldolet C12-02 2" - 10" MSS SP-97 ASTM A105
Tee C20-03
2" - 24"
Cap C22-03
According to pipe -
Conc. Red C18-03 BE ASME B16.9 ASTM A234 Gr WPB
3"
Ecc. Red C19-03
Red Tee C21-03 3" - 24"
3D 45 Bend C33-20
5D 45 Bend C34-20
4" - 24" according to manufacturer API 5L Gr B PSL 1
3D 90 Bend C35-20
5D 90 Bend C36-20
Bolts & Gasket Flanges Nipple
Straight Nipple N-S120 ½" - 1 ½" According to pipe - PBE ASTM A733 API 5L Gr B PSL 1 seamless
Spiral-Wound J-300-EH ½" - 24" - Class 300 Raised Face ASME B16.20 AISI 316/graphite
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
44 Only pipes NPS ≥ 4 are designed according to ASME B31.4/31.8.
67 Branches w ith diameter greater than or equal to half the nominal diameter of the pipe shall be fitted w ith guide bars according to DR-ENGP-I-1.14 – Standard Specification for Design of Pig L/R
77 The max imum reduction of w all thickness shall be 15% and 10% for 3d and 5d bends, respectiv ely .
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
Pipe T-102 10" 0.279" - ASME B36.10 API 5L Gr B PSL 1 (SML or WLD HFW or WLD
BE SAW)
12" 0.312"
14" 0.344"
16" 0.406" API 5L Gr B PSL 1 WLD (HFW or SAW)
Weldolet C12-02 1" - 6" BE MSS SP-97 ASTM A105
90 LR Elbow C15-03 -
45 LR Elbow C16-03
90 SR Elbow C17-03
Fittings
1" - 16"
Tee C20-03
According to pipe -
Cap C22-03 ASME B16.9 ASTM A234 Gr WPB
BE
Cross C24-03
Conc. Red C18-03
Ecc. Red C19-03 1 ½" - 16"
Red Tee C21-03
Swage Conc Nipple N-C203
Bolts & Gasket Flanges Nipple
1 ½" - 4" According to pipe - BBE MSS SP-95 ASTM A234 Gr WPB
Swage Ecc Nipple N-E203
Welding Neck (WN) F-300-K2
1" - 16" According to pipe Class 300 Raised Face ASME B16.5 ASTM A105
Blind F-300-L2
Flat type J-300-PC 1" - 16" - Class 300 Raised Face ASME B16.21 Multidirectional Expanded PTFE
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
50 Piping, fittings and acessories shall be organic coated internally acc. to I-ET-3010.00-1200-956-P4X-002 - General Painting.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
1"
Weldolet C12-30 BE MSS SP-97
2" - 14"
90 LR Elbow C15-32 -
45 LR Elbow C16-32
90 SR Elbow C17-32
2" - 30"
Tee C20-32 According to pipe -
Cap C22-32 ASME B16.9 ASTM A815 (UNS S32760)
BE
Cross C24-32
Conc. Red C18-32
Ecc. Red C19-32 3" - 30"
Red Tee C21-32
Straight Nipple N-S131 ½" - 1 ½" ASTM A733 ASTM A790 (UNS S32760)
PBE
N-C132 ¾" - 1 ½"
Nipple
2" - 24"
Welding Neck (WN) F-300-KH
26" - 30" According to pipe Class 300 Raised Face ASME B16.47 A ASTM A182 Gr F55
½" - 24" ASME B16.5
Blind F-300-LH
26" - 30" ASME B16.47 A
Bolts & Gasket
Spiral-Wound J-300-EL ½" - 30" - Class 300 Raised Face ASME B16.20 Duplex/graphite
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
26 See Annex A for v alv e casting qualification requirements.
27 See Annex D to check the piping spec range application for H2S and CO2 serv ice.
48 For temperatures abov e110°C, Superduplex shall be coated acc. to I-ET-3010.00-1200-956-P4X-002 - General Painting.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
122 Inspection of pipe and piping components shall follow ASTM A923 requirements.
123 The application of this pipe specification for PCW - Produced Water is conditioned to max imum ox y gen content 20 ppb and max temperature 120ºC.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
1" - 32"
Tee C20-03
According to pipe -
Cap C22-03 ASME B16.9 ASTM A234 Gr WPB
BE
Cross C24-03
Conc. Red C18-03
Ecc. Red C19-03 1 ½" - 32"
Red Tee C21-03
Swage Conc Nipple N-C203
Nipple
1 ½" - 4" According to pipe - BBE MSS SP-95 ASTM A234 Gr WPB
Swage Ecc Nipple N-E203
Slip on (SO) F-300-B2
1" - 24" ASME B16.5
Flanges
Flat type J-300-CC 1" - 32" - Class 300 Flat Face ASME B16.21 Multidirectional Expanded PTFE
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
28 The IW serv ice is only applicable for offshore units.
50 Piping, fittings and acessories shall be organic coated internally acc. to I-ET-3010.00-1200-956-P4X-002 - General Painting.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
Spiral-Wound J-300-EL ½" - 24" - Class 300 Raised Face ASME B16.20 Duplex/graphite
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
26 See Annex A for v alv e casting qualification requirements.
27 See Annex D to check the piping spec range application for H2S and CO2 serv ice.
29 For temperatures abov e 100°C, Duplex shall be coated acc. to I-ET-3010.00-1200-956-P4X-002 - General Painting.
58 This spec for Amine serv ice is applicable for piping dow nstream the booster pump.
82 Use this Spec after SG (free w ater separator).
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
122 Inspection of pipe and piping components shall follow ASTM A923 requirements.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 3.2 mm
16" 0.438"
Pipe - ASME B36.10
18" XS BE
20" 0.562"
T-106 ASTM A671 Gr CC60 Class 22 WLD
24" - 26" 0.625"
28" 0.688"
30" 0.750"
90 Elbow C01-04
45 Elbow C02-04
Tee C03-04
ASME B16.11
Cross C05-04 ½" - 1 ½"
Coupling C06-04 - 6000 SW
ASTM A350 Gr LF2 Cl 1
Cap C11-04
Sockolet C55-04 MSS SP-97
Red Tee C04-04
¾" - 1 ½" ASME B16.11
Fittings
2" - 24"
Welding Neck (WN) F-300-K3
26" - 30" According to pipe Class 300 Raised Face ASME B16.47 A ASTM A350 Gr LF2 Class 1
½" - 24" ASME B16.5
Blind F-300-L3
26" - 30" ASME B16.47 A
Bolts & Gasket
Spiral-Wound J-300-EH ½" - 30" - Class 300 Raised Face ASME B16.20 AISI 316/graphite
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
25 Charpy impact test is required at the minimum temperature of this spec, according to ASME B31.3 and standard material specification.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
Pipe T-410 1" - 28" acc. manufact. - ISO 14692 fiberglass type E or E-CR. Design pressure 25
Butt-Strap bar@90ºC. SML
Plug C09-36 250 THD ASME B16.15 ASTM B62 (UNS C83600)
1" - 1 ½"
Thd Saddle C52-64
- - -
Flg Saddle C51-64 1" - 6"
Coupling C06-64 Bell-Spigot
90 LR Elbow C15-64 -
Butt-Strap
45 LR Elbow C16-64
According to pipe
1" - 28" Bell-Spigot
Fittings
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
31 Electrical conductiv ity /resistiv ity shall be tested in accordance w ith ASTM D257. For components requiring electrical conductiv ity due to ex ternal charge generating mechanisms, the surface
resistiv ity shall be 10^5 ohms or less. For components requiring electrical conductiv ity due to internal charge generating mechanisms, the v olume resistiv ity shall be 10^3 ohm-meter or less.
32 GRP piping and fittings must be certified according to lev el L3 IMO A753 fire endurance test.
33 GRP piping and fittings must be supplied w ith UV protection.
34 GRP piping and fittings must hav e Ty pe Approv al certified by Classification Societies.
35 Pipes and fittings must be supplied by the same manufacturer, that also shall be responsable for design, fabrication, assembly , inspection, test, repair and comissioning.
36 Plain w ashers must be used to assembly flanged connections.
37 See Annex H for Minimum Requirements for FRP pipes and fittings.
39 The bolt torque limit shall be informed by manufacturer.
105 Whenev er non-mettalics v alv es are used, the spec´s pressure-temperature limits may be reduced according annex A (item A.7.6.2).
112 For pipes and fittings may be used as alternativ e v iny l ester resins. See Annex H.
115 Gaskets shall not be be used to assembly butterfly v alv es API 609 category A, unless required required by the v alv e manufacturer.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
12" 0.312"
Pipe -
14" 0.344" BE
T-102 ASME B36.10
16" 0.406"
18" S-30
API 5L Gr B PSL 1 WLD (HFW or SAW)
20" XS
24"
0.625"
26" API 5L Gr B PSL 1 WLD SAW
90 Elbow C01-33
45 Elbow C02-33
Tee C03-33
ASME B16.11
Cross C05-33 ½" - 1 ½"
Coupling C06-33 - 3000 SW
Cap C11-33
Sockolet C55-33 MSS SP-97
Red Tee C04-33
¾" - 1 ½" ASME B16.11 ASTM B366 (UNS N06625)
Red Coupling C08-33
Weldolet C12-33 BE MSS SP-97
90 LR Elbow C15-33 -
45 LR Elbow C16-33
90 SR Elbow C17-33 2" - 3"
ASME B16.9
Fittings
Tee C20-33
Cap C22-33
Cross C24-33 BE
Weldolet C12-02 2" - 12" MSS SP-97 ASTM A105
Conc. Red C18-33
Ecc. Red C19-33 3" - 4" ASTM B366 (UNS N06625)
According to pipe -
Red Tee C21-33
90 LR Elbow C15-03 -
45 LR Elbow C16-03
90 SR Elbow C17-03
4" - 26" ASME B16.9
Tee C20-03
Cap C22-03 ASTM A234 Gr WPB
BE
Cross C24-03
Conc. Red C18-03
Ecc. Red C19-03 6" - 26"
Red Tee C21-03
Straight Nipple N-S139 ½" - 1 ½" ASTM A733 ASTM B444 Gr 1 (UNS N06625)
PBE
N-C133 ¾" - 1 ½"
Nipple
Spiral-Wound J-300-EM ½" - 26" - Class 300 Raised Face ASME B16.20 Inconel/graphite
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
9 Charpy impact test is required at the minimum temperature of this spec, according to ASME B31.3 and API 5L requirements. Applicable to both base material and WPS qualification.
27 See Annex D to check the piping spec range application for H2S and CO2 serv ice.
42 Piping, fittings and acessories shall hav e internal Inconel® 625 cladding according to I-ET-3010.00-1200-955-P4X-001 - Welding.
103 Use this Spec after choke v alv e up to SG (free w ater separator).
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
Spiral-Wound J-600-EH ½" - 24" - Class 600 Raised Face ASME B16.20 AISI 316/graphite
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
51 For temperatures abov e 60°C, stainless steels shall be coated acc. to I-ET-3010.00-1200-956-P4X-002 - General Painting.
55 This spec for FG serv ice is applicable for piping dow nstream the filters.
59 In case of use this spec below -30 °C, the material shall be furnished w ith solution heat treatment.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
127 ISO 6162-1/2 flanges may be used only for H - Hy draulic Fluid.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
S-40S
Pipe 2" - 8" -
T-323 BE ASME B36.10/B36.19 ASTM A358 Type 316/316L Cl 1 or 3 WLD
10" - 12" S-80S
90 Elbow C01-43
45 Elbow C02-43
Tee C03-43
ASME B16.11
Cross C05-43 ½" - 1 ½"
Coupling C06-43 - 3000 SW
ASTM A182 Gr F316/316L
Cap C11-43
Sockolet C55-43 MSS SP-97
Red Tee C04-43
¾" - 1 ½" ASME B16.11
Fittings
Spiral-Wound J-600-EH ½" - 12" - Class 600 Raised Face ASME B16.20 AISI 316/graphite
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
51 For temperatures abov e 60°C, stainless steels shall be coated acc. to I-ET-3010.00-1200-956-P4X-002 - General Painting.
113 See table on item 8 for piping spec selection according to serv ice and application.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
127 ISO 6162-1/2 flanges may be used only for H - Hy draulic Fluid.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 1.6 mm
1"
Weldolet C12-02 BE MSS SP-97
2" - 10"
90 LR Elbow C15-03 -
45 LR Elbow C16-03
90 SR Elbow C17-03
2" - 24"
Tee C20-03 According to pipe -
Cap C22-03 ASME B16.9 ASTM A234 Gr WPB
BE
Cross C24-03
Conc. Red C18-03
Ecc. Red C19-03 3" - 24"
Red Tee C21-03
Straight Nipple N-S120 ½" - 1 ½" ASTM A733 API 5L Gr B PSL 1 seamless
PBE
N-C103 ¾" - 1 ½"
Nipple
Ring-Joint J-600-AN ½" - 24" - Class 600 Ring Type Joint ASME B16.20 Carbon Steel
A193 B7
Nuts
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
9 Charpy impact test is required at the minimum temperature of this spec, according to ASME B31.3 and API 5L requirements. Applicable to both base material and WPS qualification.
11 For API 5L pipe the max imum carbon equiv alent is CE iiw = 0,43% or CE pcm = 0,25%.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 3.2 mm
Pipe T-102 4" S-120 - ASME B36.10 API 5L Gr B PSL 1 (SML or WLD HFW or WLD
BE SAW)
6" 0.500"
8" 0.562"
Sockolet C55-02 ¾" - 1 ½" - 3000 SW
MSS SP-97 ASTM A105
Weldolet C12-02 2" - 3" BE
90 LR Elbow C15-03 -
45 LR Elbow C16-03
Fittings
90 SR Elbow C17-03
2" - 8"
Tee C20-03
According to pipe -
Cap C22-03 ASME B16.9 ASTM A234 Gr WPB
BE
Cross C24-03
Conc. Red C18-03
Ecc. Red C19-03 3" - 8"
Red Tee C21-03
Bolts & Gasket Flanges Nipple
Straight Nipple N-S120 ¾" According to pipe - PBE ASTM A733 API 5L Gr B PSL 1 seamless
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
HC - Half Coupling
SOC - Sockolet
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 1.6 mm
Spiral-Wound J-600-EH ½" - 24" - Class 600 Raised Face ASME B16.20 AISI 316/graphite
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
25 Charpy impact test is required at the minimum temperature of this spec, according to ASME B31.3 and standard material specification.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
Spiral-Wound J-600-EH ½" - 8" - Class 600 Raised Face ASME B16.20 AISI 316/graphite
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
SOC - Sockolet
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
9 Charpy impact test is required at the minimum temperature of this spec, according to ASME B31.3 and API 5L requirements. Applicable to both base material and WPS qualification.
52 Piping, fittings and acessories must be galv anized after spool fabrication according to ASTM A123 w ith minimum coating thickness of100µm.
63 From -18°C to 0°C, API 5L gr B shall be furnished normalized.
68 This Spec shall be applied for distribution sy stem of CO2, after directional v alv es.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
Spiral-Wound J-600-EH ½" - 8" - Class 600 Raised Face ASME B16.20 AISI 316/graphite
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
SOC - Sockolet
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
9 Charpy impact test is required at the minimum temperature of this spec, according to ASME B31.3 and API 5L requirements. Applicable to both base material and WPS qualification.
52 Piping, fittings and acessories must be galv anized after spool fabrication according to ASTM A123 w ith minimum coating thickness of100µm.
63 From -18°C to 0°C, API 5L gr B shall be furnished normalized.
68 This Spec shall be applied for distribution sy stem of CO2, after directional v alv es.
113 See table on item 8 for piping spec selection according to serv ice and application.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 3.2 mm
Spiral-Wound J-600-EH ½" - 20" - Class 600 Raised Face ASME B16.20 AISI 316/graphite
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
11 For API 5L pipe the max imum carbon equiv alent is CE iiw = 0,43% or CE pcm = 0,25%.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 1.6 mm
Spiral-Wound J-600-EH ½" - 24" - Class 600 Raised Face ASME B16.20 AISI 316/graphite
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
9 Charpy impact test is required at the minimum temperature of this spec, according to ASME B31.3 and API 5L requirements. Applicable to both base material and WPS qualification.
11 For API 5L pipe the max imum carbon equiv alent is CE iiw = 0,43% or CE pcm = 0,25%.
40 The IW serv ice is only applicable for onshore units.
56 This spec for FG serv ice is applicable for piping upstream the filters.
64 This spec for Amine serv ice is applicable for piping dow nstream the regeneration unit and upstream the contactor unit.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
14" 0.469"
Pipe - ASME B36.10
T-107 16" 0.562" BE
18" 0.625"
API 5L Gr X65 PSL 2 WLD SAW
20" 0.688"
24" 0.812"
90 LR Elbow C15-03 -
45 LR Elbow C16-03
90 SR Elbow C17-03
1" - 1 ½" ASME B16.9 ASTM A234 Gr WPB
Tee C20-03
Cap C22-03
Cross C24-03 BE
Weldolet C12-22 1" - 10" MSS SP-97 ASTM A694 Gr F65
Conc. Red C18-03
Fittings
Grooved metal J-600-GX 1" - 24" - Class 600 - ASME B16.20 AISI 316/PTFE
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
11 For API 5L pipe the max imum carbon equiv alent is CE iiw = 0,43% or CE pcm = 0,25%.
50 Piping, fittings and acessories shall be organic coated internally acc. to I-ET-3010.00-1200-956-P4X-002 - General Painting.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
14" 0.469"
Pipe - ASME B36.10
T-107 16" 0.562" BE
18" 0.625"
API 5L Gr X65 PSL 2 WLD SAW
20" 0.688"
24" 0.812"
90 LR Elbow C15-03 -
45 LR Elbow C16-03
90 SR Elbow C17-03
1" - 1 ½" ASME B16.9 ASTM A234 Gr WPB
Tee C20-03
Cap C22-03
Cross C24-03 BE
Weldolet C12-22 1" - 10" MSS SP-97 ASTM A694 Gr F65
Conc. Red C18-03
Fittings
Grooved metal J-600-GX 1" - 24" - Class 600 - ASME B16.20 AISI 316/PTFE
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
11 For API 5L pipe the max imum carbon equiv alent is CE iiw = 0,43% or CE pcm = 0,25%.
28 The IW serv ice is only applicable for offshore units.
50 Piping, fittings and acessories shall be organic coated internally acc. to I-ET-3010.00-1200-956-P4X-002 - General Painting.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
Spiral-Wound J-600-EL ½" - 16" - Class 600 Raised Face ASME B16.20 Duplex/graphite
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
26 See Annex A for v alv e casting qualification requirements.
27 See Annex D to check the piping spec range application for H2S and CO2 serv ice.
29 For temperatures abov e 100°C, Duplex shall be coated acc. to I-ET-3010.00-1200-956-P4X-002 - General Painting.
49 This spec for Amine serv ice is applicable for piping dow nstream the Amine Contactor.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
122 Inspection of pipe and piping components shall follow ASTM A923 requirements.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 6.4 mm
Spiral-Wound J-600-EH 1" - 24" - Class 600 Raised Face ASME B16.20 AISI 316/graphite
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
9 Charpy impact test is required at the minimum temperature of this spec, according to ASME B31.3 and API 5L requirements. Applicable to both base material and WPS qualification.
11 For API 5L pipe the max imum carbon equiv alent is CE iiw = 0,43% or CE pcm = 0,25%.
54 This spec for PC serv ice should only be used w hen recommended in annex D.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 3.2 mm
Spiral-Wound J-600-EH ½" - 24" - Class 600 Raised Face ASME B16.20 AISI 316/graphite
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
25 Charpy impact test is required at the minimum temperature of this spec, according to ASME B31.3 and standard material specification.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
Cap C22-33
Cross C24-33
C12-33 2" - 4" BE
Weldolet MSS SP-97
C12-22 2" - 8" ASTM A694 Gr F65
Conc. Red C18-33
Ecc. Red C19-33 3" - 4" ASME B16.9 ASTM B366 (UNS N06625)
According to pipe -
Red Tee C21-33
Cross C24-22 4" - 16"
90 LR Elbow C15-22 -
45 LR Elbow C16-22
90 SR Elbow C17-22 4" - 20"
Tee C20-22 MSS SP-75 ASTM A860 WPHY65
Cap C22-22 BE
Conc. Red C18-22
Ecc. Red C19-22 6" - 20"
Red Tee C21-22
Straight Nipple N-S139 ½" - 1 ½" ASTM A733 ASTM B444 Gr 1 (UNS N06625)
PBE
N-C133 ¾" - 1 ½"
Nipple
Spiral-Wound J-600-EM ½" - 20" - Class 600 Raised Face ASME B16.20 Inconel/graphite
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
9 Charpy impact test is required at the minimum temperature of this spec, according to ASME B31.3 and API 5L requirements. Applicable to both base material and WPS qualification.
25 Charpy impact test is required at the minimum temperature of this spec, according to ASME B31.3 and standard material specification.
27 See Annex D to check the piping spec range application for H2S and CO2 serv ice.
42 Piping, fittings and acessories shall hav e internal Inconel® 625 cladding according to I-ET-3010.00-1200-955-P4X-001 - Welding.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
Cap C22-33
Cross C24-33 BE
Weldolet C12-33 2" - 6" MSS SP-97
Conc. Red C18-33
Ecc. Red C19-33 3" - 4"
Red Tee C21-33 According to pipe -
90 LR Elbow C15-11 -
45 LR Elbow C16-11
90 SR Elbow C17-11
4" - 16" ASME B16.9
Tee C20-11
Cap C22-11 ASTM A420 Gr WPL3
BE
Cross C24-11
Conc. Red C18-11
Ecc. Red C19-11 6" - 16"
Red Tee C21-11
Straight Nipple N-S139 ½" - 1 ½" ASTM A733 ASTM B444 Gr 1 (UNS N06625)
PBE
N-C133 ¾" - 1 ½"
Nipple
Spiral-Wound J-600-EM ½" - 16" - Class 600 Raised Face ASME B16.20 Inconel/graphite
A320 L7
Nuts
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
27 See Annex D to check the piping spec range application for H2S and CO2 serv ice.
42 Piping, fittings and acessories shall hav e internal Inconel® 625 cladding according to I-ET-3010.00-1200-955-P4X-001 - Welding.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
10" 0.594"
Pipe -
T-323 12" 0.688" BE ASME B36.10/B36.19 ASTM A358 Type 316/316L Cl 1 or 3 WLD
14" 0.750"
16" 0.844"
18" 1.000"
90 Elbow C01-43
45 Elbow C02-43
Tee C03-43
ASME B16.11
Cross C05-43 ½" - 1 ½"
Coupling C06-43 - 3000 SW
ASTM A182 Gr F316/316L
Cap C11-43
Sockolet C55-43 MSS SP-97
Red Tee C04-43
¾" - 1 ½" ASME B16.11
Fittings
Ring-Joint - Ring Type Joint ASME B16.20 Stainless Steel AISI 316
J-900-AT 3" - 18" Class 900
A320 L7, Zn-Ni
Nuts
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
27 See Annex D to check the piping spec range application for H2S and CO2 serv ice.
51 For temperatures abov e 60°C, stainless steels shall be coated acc. to I-ET-3010.00-1200-956-P4X-002 - General Painting.
59 In case of use this spec below -30 °C, the material shall be furnished w ith solution heat treatment.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
127 ISO 6162-1/2 flanges may be used only for H - Hy draulic Fluid.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
Ring-Joint - Ring Type Joint ASME B16.20 Stainless Steel AISI 316
J-900-AT 3" - 12" Class 900
A193 B7, Zn-Ni
Nuts
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
51 For temperatures abov e 60°C, stainless steels shall be coated acc. to I-ET-3010.00-1200-956-P4X-002 - General Painting.
113 See table on item 8 for piping spec selection according to serv ice and application.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
127 ISO 6162-1/2 flanges may be used only for H - Hy draulic Fluid.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 1.6 mm
1"
Weldolet C12-02 BE MSS SP-97
2" - 8"
90 LR Elbow C15-03 -
45 LR Elbow C16-03
90 SR Elbow C17-03
2" - 18"
Tee C20-03 According to pipe -
Cap C22-03 ASME B16.9 ASTM A234 Gr WPB
BE
Cross C24-03
Conc. Red C18-03
Ecc. Red C19-03 3" - 18"
Red Tee C21-03
Straight Nipple N-S120 ½" - 1 ½" ASTM A733 API 5L Gr B PSL 1 seamless
PBE
N-C103 ¾" - 1 ½"
Nipple
F-1500-R2 2"
Welding Neck (WN)
F-900-R2 3" - 18" According to pipe Class 900 Ring Type Joint ASME B16.5 ASTM A105
F-1500-S2 ½" - 2" Class 1500
Blind
F-900-S2 3" - 18" Class 900
J-1500-AN ½" - 2" Class 1500
Bolts & Gasket
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
11 For API 5L pipe the max imum carbon equiv alent is CE iiw = 0,43% or CE pcm = 0,25%.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 3.2 mm
2" - 3"
Pipe - ASME B36.10
T-107 4" S-120 BE API 5L Gr X65 PSL 2 (SML or WLD SAW)
6" 0.500"
Sockolet C55-02 ¾" - 1 ½" - 6000 SW ASTM A105
MSS SP-97
Weldolet C12-22 2" BE ASTM A694 Gr F65
90 LR Elbow C15-22 -
45 LR Elbow C16-22
Fittings
90 SR Elbow C17-22
2" - 6"
Tee C20-22
According to pipe -
Cap C22-22 MSS SP-75 ASTM A860 WPHY65
BE
Cross C24-22
Conc. Red C18-22
Ecc. Red C19-22 3" - 6"
Red Tee C21-22
Nipple
Straight Nipple N-S120 ¾" According to pipe - PBE ASTM A733 API 5L Gr B PSL 1 seamless
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
HC - Half Coupling
SOC - Sockolet
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 1.6 mm
F-1500-R3 2"
Welding Neck (WN)
F-900-R3 3" - 20" According to pipe Class 900 Ring Type Joint ASME B16.5 ASTM A350 Gr LF2 Class 1
F-1500-S3 ½" - 2" Class 1500
Blind
F-900-S3 3" - 20" Class 900
J-1500-AT ½" - 2" Class 1500
Bolts & Gasket
Ring-Joint - Ring Type Joint ASME B16.20 Stainless Steel AISI 316
J-900-AT 3" - 20" Class 900
A193 B7, Zn-Ni
Nuts
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
25 Charpy impact test is required at the minimum temperature of this spec, according to ASME B31.3 and standard material specification.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 1.6 mm
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
9 Charpy impact test is required at the minimum temperature of this spec, according to ASME B31.3 and API 5L requirements. Applicable to both base material and WPS qualification.
11 For API 5L pipe the max imum carbon equiv alent is CE iiw = 0,43% or CE pcm = 0,25%.
40 The IW serv ice is only applicable for onshore units.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.8 1.6 mm
45 LR Elbow C16-22
2" - 3" MSS SP-75 ASTM A860 WPHY65
90 SR Elbow C17-22
Cross C24-22
Weldolet C12-22 2" - 16" MSS SP-97 ASTM A694 Gr F65
Tee C20-22
2" - 34"
Cap C22-22
According to pipe -
Conc. Red C18-22 BE MSS SP-75 ASTM A860 WPHY65
3"
Ecc. Red C19-22
Red Tee C21-22 3" - 34"
3D 45 Bend C33-21
5D 45 Bend C34-21
4" - 34" according to manufacturer API 5L Gr X65 PSL 2
3D 90 Bend C35-21
5D 90 Bend C36-21
Nipple
Straight Nipple N-S120 ½" - 1 ½" According to pipe - PBE ASTM A733 API 5L Gr B PSL 1 seamless
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
9 Charpy impact test is required at the minimum temperature of this spec, according to ASME B31.3 and API 5L requirements. Applicable to both base material and WPS qualification.
11 For API 5L pipe the max imum carbon equiv alent is CE iiw = 0,43% or CE pcm = 0,25%.
44 Only pipes NPS ≥ 4 are designed according to ASME B31.4/31.8.
67 Branches w ith diameter greater than or equal to half the nominal diameter of the pipe shall be fitted w ith guide bars according to DR-ENGP-I-1.14 – Standard Specification for Design of Pig L/R
77 The max imum reduction of w all thickness shall be 15% and 10% for 3d and 5d bends, respectiv ely .
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
11 For API 5L pipe the max imum carbon equiv alent is CE iiw = 0,43% or CE pcm = 0,25%.
50 Piping, fittings and acessories shall be organic coated internally acc. to I-ET-3010.00-1200-956-P4X-002 - General Painting.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
11 For API 5L pipe the max imum carbon equiv alent is CE iiw = 0,43% or CE pcm = 0,25%.
28 The IW serv ice is only applicable for offshore units.
50 Piping, fittings and acessories shall be organic coated internally acc. to I-ET-3010.00-1200-956-P4X-002 - General Painting.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
10" - 12"
Pipe - ASME B36.10/B36.19
14" 0.562" BE
T-302 16" 0.625" ASTM A928 (UNS S31803 Cl 1 or 3) WLD
18" 0.688"
20" 0.750"
90 Elbow C01-27
45 Elbow C02-27
Tee C03-27
ASME B16.11
Cross C05-27 ½" - 1 ½"
Coupling C06-27 - 3000 SW
ASTM A182 Gr F51 (UNS S31803)
Cap C11-27
Sockolet C55-27 MSS SP-97
Red Tee C04-27
¾" - 1 ½" ASME B16.11
Fittings
F-1500-RG 2"
Welding Neck (WN)
F-900-RG 3" - 20" According to pipe Class 900 Ring Type Joint ASME B16.5 ASTM A182 Gr F51
F-1500-SG ½" - 2" Class 1500
Blind
F-900-SG 3" - 20" Class 900
J-1500-AU ½" - 2" Class 1500
Bolts & Gasket
Ring-Joint - Ring Type Joint ASME B16.20 Duplex , ASTM A182 F51
J-900-AU 3" - 20" Class 900
A193 B7, Zn-Ni
Nuts
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
26 See Annex A for v alv e casting qualification requirements.
27 See Annex D to check the piping spec range application for H2S and CO2 serv ice.
29 For temperatures abov e 100°C, Duplex shall be coated acc. to I-ET-3010.00-1200-956-P4X-002 - General Painting.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
122 Inspection of pipe and piping components shall follow ASTM A923 requirements.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
10" 0.562"
Pipe -
12" S-80 BE
T-107 ASME B36.10
14" 0.688"
16" S-80
18" 0.875"
API 5L Gr X65 PSL 2 WLD SAW
20" 0.938"
24" 1.125"
90 Elbow C01-33
45 Elbow C02-33
Tee C03-33
ASME B16.11
Cross C05-33 ½" - 1 ½"
Coupling C06-33 - 3000 SW
Cap C11-33
Sockolet C55-33 MSS SP-97
Red Tee C04-33
¾" - 1 ½" ASME B16.11 ASTM B366 (UNS N06625)
Red Coupling C08-33
Weldolet C12-33 BE MSS SP-97
90 LR Elbow C15-33 -
45 LR Elbow C16-33
90 SR Elbow C17-33 2" - 3"
ASME B16.9
Fittings
Tee C20-33
Cap C22-33
Cross C24-33 BE
Weldolet C12-22 2" - 10" MSS SP-97 ASTM A694 Gr F65
Conc. Red C18-33
Ecc. Red C19-33 3" - 4" ASME B16.9 ASTM B366 (UNS N06625)
According to pipe -
Red Tee C21-33
90 LR Elbow C15-22 -
45 LR Elbow C16-22
90 SR Elbow C17-22
4" - 24"
Tee C20-22
Cap C22-22 MSS SP-75 ASTM A860 WPHY65
BE
Cross C24-22
Conc. Red C18-22
Ecc. Red C19-22 6" - 24"
Red Tee C21-22
Straight Nipple N-S139 ½" - 1 ½" ASTM A733 ASTM B444 Gr 1 (UNS N06625)
PBE
N-C133 ¾" - 1 ½"
Nipple
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
9 Charpy impact test is required at the minimum temperature of this spec, according to ASME B31.3 and API 5L requirements. Applicable to both base material and WPS qualification.
11 For API 5L pipe the max imum carbon equiv alent is CE iiw = 0,43% or CE pcm = 0,25%.
27 See Annex D to check the piping spec range application for H2S and CO2 serv ice.
42 Piping, fittings and acessories shall hav e internal Inconel® 625 cladding according to I-ET-3010.00-1200-955-P4X-001 - Welding.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
6" - 8" XS
Pipe -
10" 0.625" BE ASTM A333 Gr 3 SML( or or WLD)
T-211 ASME B36.10
12" 0.750"
14" 0.812"
16" 0.938" ASTM A333 Gr 3 WLD( or )
90 Elbow C01-33
45 Elbow C02-33
Tee C03-33
ASME B16.11
Cross C05-33 ½" - 1 ½"
Coupling C06-33 - 3000 SW
Cap C11-33
Sockolet C55-33 MSS SP-97
Red Tee C04-33
¾" - 1 ½" ASME B16.11 ASTM B366 (UNS N06625)
Red Coupling C08-33
Weldolet C12-33 BE MSS SP-97
90 LR Elbow C15-33 -
45 LR Elbow C16-33
90 SR Elbow C17-33 2" - 3"
ASME B16.9
Fittings
Tee C20-33
Cap C22-33
Cross C24-33 BE
Weldolet C12-10 2" - 6" MSS SP-97 ASTM A350 Gr LF3
Conc. Red C18-33
Ecc. Red C19-33 3" - 4" ASTM B366 (UNS N06625)
According to pipe -
Red Tee C21-33
90 LR Elbow C15-11 -
45 LR Elbow C16-11
90 SR Elbow C17-11
4" - 16" ASME B16.9
Tee C20-11
Cap C22-11 ASTM A420 Gr WPL3
BE
Cross C24-11
Conc. Red C18-11
Ecc. Red C19-11 6" - 16"
Red Tee C21-11
Straight Nipple N-S139 ½" - 1 ½" ASTM A733 ASTM B444 Gr 1 (UNS N06625)
PBE
N-C133 ¾" - 1 ½"
Nipple
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
27 See Annex D to check the piping spec range application for H2S and CO2 serv ice.
42 Piping, fittings and acessories shall hav e internal Inconel® 625 cladding according to I-ET-3010.00-1200-955-P4X-001 - Welding.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
1"
Weldolet C12-43 BE MSS SP-97
2" - 6"
90 LR Elbow C15-44 -
45 LR Elbow C16-44
90 SR Elbow C17-44
2" - 16"
Tee C20-44 According to pipe -
Cap C22-44 ASME B16.9 ASTM A403 Gr WP316/316L
BE
Cross C24-44
Conc. Red C18-44
Ecc. Red C19-44 3" - 16"
Red Tee C21-44
Straight Nipple N-S145 ½" - 1 ½" ASTM A733 ASTM A312 TP316/316L
PBE
N-C144 ¾" - 1 ½"
Nipple
Ring-Joint J-1500-AT ½" - 16" - Class 1500 Ring Type Joint ASME B16.20 Stainless Steel AISI 316
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
51 For temperatures abov e 60°C, stainless steels shall be coated acc. to I-ET-3010.00-1200-956-P4X-002 - General Painting.
59 In case of use this spec below -30 °C, the material shall be furnished w ith solution heat treatment.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
127 ISO 6162-1/2 flanges may be used only for H - Hy draulic Fluid.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 1.6 mm
4" S-120
Pipe T-102 - ASME B36.10 API 5L Gr B PSL 1 (SML or WLD HFW or WLD
6" 0.625" BE SAW)
8" 0.750"
10" 0.938"
90 Elbow C01-02
45 Elbow C02-02
Tee C03-02
ASME B16.11
Cross C05-02 ½" - 1 ½"
Coupling C06-02 - 6000 SW
ASTM A105
Cap C11-02
Sockolet C55-02 MSS SP-97
Red Tee C04-02
¾" - 1 ½" ASME B16.11
Fittings
Ring-Joint J-1500-AN ½" - 10" - Class 1500 Ring Type Joint ASME B16.20 Carbon Steel
A193 B7
Nuts
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
SOC - Sockolet
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
11 For API 5L pipe the max imum carbon equiv alent is CE iiw = 0,43% or CE pcm = 0,25%.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 3.2 mm
90 SR Elbow C17-22
2" - 6"
Tee C20-22 According to pipe -
Cap C22-22 MSS SP-75 ASTM A860 WPHY65
BE
Cross C24-22
Conc. Red C18-22
Ecc. Red C19-22 3" - 6"
Red Tee C21-22
Bolts & Gasket Flanges Nipple
Straight Nipple N-S120 ¾" - 1" According to pipe - PBE ASTM A733 API 5L Gr B PSL 1 seamless
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
HC - Half Coupling
SOC - Sockolet
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
11 For API 5L pipe the max imum carbon equiv alent is CE iiw = 0,43% or CE pcm = 0,25%.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 1.6 mm
Ring-Joint J-1500-AT ½" - 18" - Class 1500 Ring Type Joint ASME B16.20 Stainless Steel AISI 316
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
25 Charpy impact test is required at the minimum temperature of this spec, according to ASME B31.3 and standard material specification.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 1.6 mm
Pipe 8" 0.750" - ASME B36.10 API 5L Gr X65 PSL 2 (SML or WLD SAW)
T-107 BE
10" 0.938"
12" 1.062"
14" 1.125"
16" - 24" S-140 API 5L Gr X65 PSL 2 WLD SAW
90 Elbow C01-02
45 Elbow C02-02
Tee C03-02
ASME B16.11
Cross C05-02 ½" - 1 ½"
Coupling C06-02 - 6000 SW ASTM A105
Cap C11-02
Sockolet C55-02 MSS SP-97
Red Tee C04-02
¾" - 1 ½" ASME B16.11
Fittings
Ring-Joint J-1500-AN ½" - 24" - Class 1500 Ring Type Joint ASME B16.20 Carbon Steel
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
9 Charpy impact test is required at the minimum temperature of this spec, according to ASME B31.3 and API 5L requirements. Applicable to both base material and WPS qualification.
11 For API 5L pipe the max imum carbon equiv alent is CE iiw = 0,43% or CE pcm = 0,25%.
40 The IW serv ice is only applicable for onshore units.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.8 1.6 mm
Pipe 8" 0.750" - ASME B36.10 API 5L Gr X65 PSL 2 (SML or WLD SAW)
T-107 BE
10" 0.938"
12" 1.062"
14" 1.125"
16" - 24" S-140 API 5L Gr X65 PSL 2 WLD SAW
90 Elbow C01-02
45 Elbow C02-02
Tee C03-02
ASME B16.11
Cross C05-02 ½" - 1 ½"
Coupling C06-02 - 6000 SW ASTM A105
Cap C11-02
Sockolet C55-02 MSS SP-97
Red Tee C04-02
¾" - 1 ½" ASME B16.11
Red Coupling C08-02
Weldolet C12-22 1" - 10" BE MSS SP-97 ASTM A694 Gr F65
Fittings
90 LR Elbow C15-22 -
45 LR Elbow C16-22
90 SR Elbow C17-22
2" - 3"
Conc. Red C18-22
Ecc. Red C19-22 MSS SP-75 ASTM A860 WPHY65
Cross C24-22
According to pipe -
Tee C20-22
2" - 24" BE
Cap C22-22
Red Tee C21-22 3" - 24"
3D 45 Bend C33-21
5D 45 Bend C34-21
4" - 24" according to manufacturer API 5L Gr X65 PSL 2
3D 90 Bend C35-21
5D 90 Bend C36-21
Bolts & Gasket Flanges Nipple
Straight Nipple N-S120 ½" - 1 ½" According to pipe - PBE ASTM A733 API 5L Gr B PSL 1 seamless
Ring-Joint J-1500-AN ½" - 24" - Class 1500 Ring Type Joint ASME B16.20 Carbon Steel
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
9 Charpy impact test is required at the minimum temperature of this spec, according to ASME B31.3 and API 5L requirements. Applicable to both base material and WPS qualification.
11 For API 5L pipe the max imum carbon equiv alent is CE iiw = 0,43% or CE pcm = 0,25%.
44 Only pipes NPS ≥ 4 are designed according to ASME B31.4/31.8.
67 Branches w ith diameter greater than or equal to half the nominal diameter of the pipe shall be fitted w ith guide bars according to DR-ENGP-I-1.14 – Standard Specification for Design of Pig L/R
77 The max imum reduction of w all thickness shall be 15% and 10% for 3d and 5d bends, respectiv ely .
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
Ring-Joint J-1500-AV 1" - 24" - Class 1500 Ring Type Joint ASME B16.20 Inconel
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
9 Charpy impact test is required at the minimum temperature of this spec, according to ASME B31.3 and API 5L requirements. Applicable to both base material and WPS qualification.
11 For API 5L pipe the max imum carbon equiv alent is CE iiw = 0,43% or CE pcm = 0,25%.
50 Piping, fittings and acessories shall be organic coated internally acc. to I-ET-3010.00-1200-956-P4X-002 - General Painting.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
12" 0.688"
Pipe - ASME B36.10/B36.19
14" 0.750" BE
T-304 16" 0.812" ASTM A928 (UNS S32760 Cl 1 or 3) WLD
18" 0.938"
20" 1.031"
24" 1.219"
90 Elbow C01-30
45 Elbow C02-30
Tee C03-30
ASME B16.11
Cross C05-30 ½" - 1 ½"
Coupling C06-30 - 3000 SW
ASTM A182 Gr F55 (UNS S32760)
Cap C11-30
Sockolet C55-30 MSS SP-97
Red Tee C04-30
¾" - 1 ½" ASME B16.11
Fittings
Ring-Joint J-1500-AU 1" - 24" - Class 1500 Ring Type Joint ASME B16.20 Duplex , ASTM A182 F51
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
26 See Annex A for v alv e casting qualification requirements.
27 See Annex D to check the piping spec range application for H2S and CO2 serv ice.
48 For temperatures abov e110°C, Superduplex shall be coated acc. to I-ET-3010.00-1200-956-P4X-002 - General Painting.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
122 Inspection of pipe and piping components shall follow ASTM A923 requirements.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.8 -
8" 0.406"
Pipe - ASME B36.10/B36.19
10" 0.562" BE
12" 0.625"
T-304 14" 0.688" ASTM A928 (UNS S32760 Cl 1 or 3) WLD
16" 0.750"
18" 0.875"
90 Elbow C01-30
45 Elbow C02-30
Tee C03-30
ASME B16.11
Cross C05-30 ½" - 1 ½"
Coupling C06-30 - 3000 SW
ASTM A182 Gr F55 (UNS S32760)
Cap C11-30
Sockolet C55-30 MSS SP-97
Red Tee C04-30
¾" - 1 ½" ASME B16.11
Red Coupling C08-30
Weldolet C12-30 1" - 8" BE MSS SP-97
90 LR Elbow C15-32 -
Fittings
Ring-Joint J-1500-AU ½" - 18" - Class 1500 Ring Type Joint ASME B16.20 Duplex , ASTM A182 F51
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
26 See Annex A for v alv e casting qualification requirements.
27 See Annex D to check the piping spec range application for H2S and CO2 serv ice.
44 Only pipes NPS ≥ 4 are designed according to ASME B31.4/31.8.
48 For temperatures abov e110°C, Superduplex shall be coated acc. to I-ET-3010.00-1200-956-P4X-002 - General Painting.
67 Branches w ith diameter greater than or equal to half the nominal diameter of the pipe shall be fitted w ith guide bars according to DR-ENGP-I-1.14 – Standard Specification for Design of Pig L/R
77 The max imum reduction of w all thickness shall be 15% and 10% for 3d and 5d bends, respectiv ely .
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
122 Inspection of pipe and piping components shall follow ASTM A923 requirements.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
Ring-Joint J-1500-AV 1" - 18" - Class 1500 Ring Type Joint ASME B16.20 Inconel
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
9 Charpy impact test is required at the minimum temperature of this spec, according to ASME B31.3 and API 5L requirements. Applicable to both base material and WPS qualification.
11 For API 5L pipe the max imum carbon equiv alent is CE iiw = 0,43% or CE pcm = 0,25%.
28 The IW serv ice is only applicable for offshore units.
50 Piping, fittings and acessories shall be organic coated internally acc. to I-ET-3010.00-1200-956-P4X-002 - General Painting.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
Ring-Joint J-1500-AU ½" - 24" - Class 1500 Ring Type Joint ASME B16.20 Duplex , ASTM A182 F51
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
26 See Annex A for v alv e casting qualification requirements.
27 See Annex D to check the piping spec range application for H2S and CO2 serv ice.
29 For temperatures abov e 100°C, Duplex shall be coated acc. to I-ET-3010.00-1200-956-P4X-002 - General Painting.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
122 Inspection of pipe and piping components shall follow ASTM A923 requirements.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
6" 0.500"
Pipe - ASME B36.10/B36.19
8" 0.594" BE
10" 0.719"
T-302 ASTM A928 (UNS S31803 Cl 1 or 3) WLD
12" 0.812"
90 Elbow C01-27
45 Elbow C02-27
Tee C03-27
ASME B16.11
Cross C05-27 ½" - 1 ½"
Coupling C06-27 - 3000 SW
ASTM A182 Gr F51 (UNS S31803)
Cap C11-27
Sockolet C55-27 MSS SP-97
Red Tee C04-27
¾" - 1 ½" ASME B16.11
Fittings
Ring-Joint J-1500-AU ½" - 12" - Class 1500 Ring Type Joint ASME B16.20 Duplex , ASTM A182 F51
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
26 See Annex A for v alv e casting qualification requirements.
29 For temperatures abov e 100°C, Duplex shall be coated acc. to I-ET-3010.00-1200-956-P4X-002 - General Painting.
113 See table on item 8 for piping spec selection according to serv ice and application.
122 Inspection of pipe and piping components shall follow ASTM A923 requirements.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
127 ISO 6162-1/2 flanges may be used only for H - Hy draulic Fluid.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
6" 0.432"
Pipe - ASME B36.10/B36.19
8" 0.562" BE
10" 0.719"
T-302 12" 0.750" ASTM A928 (UNS S31803 Cl 1 or 3) WLD
14" 0.875"
90 Elbow C01-27
45 Elbow C02-27
Tee C03-27
ASME B16.11
Cross C05-27 ½" - 1 ½"
Coupling C06-27 - 3000 SW
ASTM A182 Gr F51 (UNS S31803)
Cap C11-27
Sockolet C55-27 MSS SP-97
Red Tee C04-27
¾" - 1 ½" ASME B16.11
Red Coupling C08-27
Weldolet C12-27 1" - 6" BE MSS SP-97
90 LR Elbow C15-29 -
Fittings
Straight Nipple N-S128 ½" - 1 ½" According to pipe - PBE ASTM A733 ASTM A790 (UNS S31803)
Ring-Joint J-1500-AU ½" - 14" - Class 1500 Ring Type Joint ASME B16.20 Duplex , ASTM A182 F51
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
26 See Annex A for v alv e casting qualification requirements.
27 See Annex D to check the piping spec range application for H2S and CO2 serv ice.
29 For temperatures abov e 100°C, Duplex shall be coated acc. to I-ET-3010.00-1200-956-P4X-002 - General Painting.
44 Only pipes NPS ≥ 4 are designed according to ASME B31.4/31.8.
67 Branches w ith diameter greater than or equal to half the nominal diameter of the pipe shall be fitted w ith guide bars according to DR-ENGP-I-1.14 – Standard Specification for Design of Pig L/R
77 The max imum reduction of w all thickness shall be 15% and 10% for 3d and 5d bends, respectiv ely .
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
122 Inspection of pipe and piping components shall follow ASTM A923 requirements.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 3.2 mm
2" - 6"
Pipe T-105 - ASME B36.10 ASTM A333 Gr 6 SML
8" 1.000" BE
10" 1.250"
90 Elbow C01-04
45 Elbow C02-04
Tee C03-04
ASME B16.11 ASTM A350 Gr LF2 Cl 1
Cross C05-04 ½" - 1 ½"
Coupling C06-04 - 9000 SW
Cap C11-04
Sockolet C55-02 MSS SP-97 ASTM A105
Red Tee C04-04
¾" - 1 ½" ASME B16.11
Fittings
Ring-Joint J-1500-AT ½" - 10" - Class 1500 Ring Type Joint ASME B16.20 Stainless Steel AISI 316
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
SOC - Sockolet
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
25 Charpy impact test is required at the minimum temperature of this spec, according to ASME B31.3 and standard material specification.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
4" 0.531"
Pipe -
6" 0.864"
T-323 BE ASME B36.10/B36.19 ASTM A358 Type 316/316L Cl 1 or 3 WLD
8" 1.250"
10" - 12" 1.500"
14" 1.750"
16" 2.000"
Weldolet C12-43 1" - 6" BE MSS SP-97 ASTM A182 Gr F316/316L
90 LR Elbow C15-44 -
45 LR Elbow C16-44
90 SR Elbow C17-44 1" - 16"
Fittings
Cap C22-44
According to pipe -
Cross C24-44 ASME B16.9 ASTM A403 Gr WP316/316L
BE
Red Tee C21-44 1 ½" - 16"
Conc. Red C18-44
Ecc. Red C19-44 2" - 16"
Tee C20-44
Welding Neck (WN) F-2500-RX 1" - 12" Class 2500 Ring Type Joint ASME B16.5
F-420-4X 1" - 3" max 420 bar - ISO 6162-2
Flanges
Blind
F-2500-SX 1" - 12" Ring Type Joint ASME B16.5
According to pipe ASTM A182 Gr F316/316L
Compact WN F-2500-UX Class 2500
1" - 16" IX seal ring ISO 27509
Compact Blind F-2500-VX
Hyd One-Piece Flange F-420-3X 1" - 3" max 420 bar - ISO 6162-2
J-2500-AT 1" - 12" Ring Type Joint ASME B16.20
Bolts & Gasket
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
51 For temperatures abov e 60°C, stainless steels shall be coated acc. to I-ET-3010.00-1200-956-P4X-002 - General Painting.
59 In case of use this spec below -30 °C, the material shall be furnished w ith solution heat treatment.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
127 ISO 6162-1/2 flanges may be used only for H - Hy draulic Fluid.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 3.2 mm
Pipe T-107 - BE ASME B36.10 API 5L Gr X65 PSL 2 (SML or WLD SAW)
6" 0.875"
Weldolet C12-22 2" BE MSS SP-97 ASTM A694 Gr F65
90 LR Elbow C15-22 -
45 LR Elbow C16-22
90 SR Elbow C17-22
Fittings
2" - 6"
Tee C20-22
According to pipe -
Cap C22-22 MSS SP-75 ASTM A860 WPHY65
BE
Cross C24-22
Conc. Red C18-22
Ecc. Red C19-22 3" - 6"
Red Tee C21-22
Bolts & Gasket Flanges
Ring-Joint J-2500-AN 2" - 6" - Class 2500 Ring Type Joint ASME B16.20 Carbon Steel
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
HC - Half Coupling
SOC - Sockolet
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
9 Charpy impact test is required at the minimum temperature of this spec, according to ASME B31.3 and API 5L requirements. Applicable to both base material and WPS qualification.
11 For API 5L pipe the max imum carbon equiv alent is CE iiw = 0,43% or CE pcm = 0,25%.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 1.6 mm
1" - 18"
Tee C20-05
According to pipe -
Cap C22-05 ASME B16.9 ASTM A420 Gr WPL6
BE
Cross C24-05
Conc. Red C18-05
Ecc. Red C19-05 1 ½" - 18"
Red Tee C21-05
Straight Nipple N-S237 1" - 1 ½" ASTM A733 ASTM A333 Gr 6
Nipple
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
25 Charpy impact test is required at the minimum temperature of this spec, according to ASME B31.3 and standard material specification.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 1.6 mm
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
9 Charpy impact test is required at the minimum temperature of this spec, according to ASME B31.3 and API 5L requirements. Applicable to both base material and WPS qualification.
11 For API 5L pipe the max imum carbon equiv alent is CE iiw = 0,43% or CE pcm = 0,25%.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.8 1.6 mm
Pipe 2" - 14" - ASME B36.10 API 5L Gr X65 PSL 2 (SML or WLD SAW)
T-107 S-160 BE
16" - 20" API 5L Gr X65 PSL 2 WLD SAW
90 LR Elbow C15-03 -
45 LR Elbow C16-03
90 SR Elbow C17-03
1" - 1 ½" ASME B16.9 ASTM A234 Gr WPB
Tee C20-03
Cap C22-03
Cross C24-03 BE
Weldolet C12-22 1" - 8" MSS SP-97 ASTM A694 Gr F65
Conc. Red C18-03
Ecc. Red C19-03 1 ½" ASME B16.9 ASTM A234 Gr WPB
Red Tee C21-03
Fittings
90 LR Elbow C15-22 -
45 LR Elbow C16-22 According to pipe -
90 SR Elbow C17-22 2" - 3"
Conc. Red C18-22
Ecc. Red C19-22 MSS SP-75 ASTM A860 WPHY65
Tee C20-22
Red Tee C21-22
2" - 20" BE
Cap C22-22
Cross C24-22
3D 45 Bend C33-21
5D 45 Bend C34-21
4" - 20" according to manufacturer API 5L Gr X65 PSL 2
3D 90 Bend C35-21
5D 90 Bend C36-21
Nipple
Straight Nipple N-S220 1" - 1 ½" According to pipe - BBE ASTM A733 API 5L Gr B PSL 1 seamless
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
9 Charpy impact test is required at the minimum temperature of this spec, according to ASME B31.3 and API 5L requirements. Applicable to both base material and WPS qualification.
11 For API 5L pipe the max imum carbon equiv alent is CE iiw = 0,43% or CE pcm = 0,25%.
44 Only pipes NPS ≥ 4 are designed according to ASME B31.4/31.8.
67 Branches w ith diameter greater than or equal to half the nominal diameter of the pipe shall be fitted w ith guide bars according to DR-ENGP-I-1.14 – Standard Specification for Design of Pig L/R
77 The max imum reduction of w all thickness shall be 15% and 10% for 3d and 5d bends, respectiv ely .
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 1.6 mm
Ring-Joint J-2500-AN 1" - 4" - Class 2500 Ring Type Joint ASME B16.20 Carbon Steel
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
HC - Half Coupling
SOC - Sockolet
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
9 Charpy impact test is required at the minimum temperature of this spec, according to ASME B31.3 and API 5L requirements. Applicable to both base material and WPS qualification.
11 For API 5L pipe the max imum carbon equiv alent is CE iiw = 0,43% or CE pcm = 0,25%.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
SOC - Sockolet
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
9 Charpy impact test is required at the minimum temperature of this spec, according to ASME B31.3 and API 5L requirements. Applicable to both base material and WPS qualification.
11 For API 5L pipe the max imum carbon equiv alent is CE iiw = 0,43% or CE pcm = 0,25%.
50 Piping, fittings and acessories shall be organic coated internally acc. to I-ET-3010.00-1200-956-P4X-002 - General Painting.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
10" 0.875"
Pipe - ASME B36.10/B36.19
12" 1.062" BE
14" 1.125"
T-304 16" 1.438" ASTM A928 (UNS S32760 Cl 1 or 3) WLD
18" 1.562"
20" 1.750"
24" 2.062"
Weldolet C12-30 1" - 10" BE MSS SP-97 ASTM A182 Gr F55 (UNS S32760)
90 LR Elbow C15-32 -
45 LR Elbow C16-32
90 SR Elbow C17-32
Fittings
1" - 24"
Tee C20-32
According to pipe -
Cap C22-32 ASME B16.9 ASTM A815 (UNS S32760)
BE
Cross C24-32
Conc. Red C18-32
Ecc. Red C19-32 1 ½" - 24"
Red Tee C21-32
Straight Nipple N-S231 1" - 1 ½" ASTM A733 ASTM A790 (UNS S32760)
Nipple
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
26 See Annex A for v alv e casting qualification requirements.
27 See Annex D to check the piping spec range application for H2S and CO2 serv ice.
48 For temperatures abov e110°C, Superduplex shall be coated acc. to I-ET-3010.00-1200-956-P4X-002 - General Painting.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
122 Inspection of pipe and piping components shall follow ASTM A923 requirements.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.8 -
6" 0.500"
Pipe - ASME B36.10/B36.19
8" 0.719" BE
10" 0.812"
12" 1.000"
T-304 ASTM A928 (UNS S32760 Cl 1 or 3) WLD
14" 1.062"
18" 1.375"
90 LR Elbow C15-32 -
45 LR Elbow C16-32 1" - 3" ASME B16.9 ASTM A815 (UNS S32760)
90 SR Elbow C17-32
Weldolet C12-30 1" - 8" MSS SP-97 ASTM A182 Gr F55 (UNS S32760)
Tee C20-32
Cap C22-32 1" - 14"
Cross C24-32
ASME B16.9 ASTM A815 (UNS S32760)
Conc. Red C18-32
1 ½" - 3"
Ecc. Red C19-32
Fittings
Straight Nipple N-S231 1" - 1 ½" According to pipe - BBE ASTM A733 ASTM A790 (UNS S32760)
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
26 See Annex A for v alv e casting qualification requirements.
27 See Annex D to check the piping spec range application for H2S and CO2 serv ice.
44 Only pipes NPS ≥ 4 are designed according to ASME B31.4/31.8.
48 For temperatures abov e110°C, Superduplex shall be coated acc. to I-ET-3010.00-1200-956-P4X-002 - General Painting.
67 Branches w ith diameter greater than or equal to half the nominal diameter of the pipe shall be fitted w ith guide bars according to DR-ENGP-I-1.14 – Standard Specification for Design of Pig L/R
77 The max imum reduction of w all thickness shall be 15% and 10% for 3d and 5d bends, respectiv ely .
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
122 Inspection of pipe and piping components shall follow ASTM A923 requirements.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
10" 0.938"
Pipe - ASME B36.10/B36.19
12" 1.062" BE
14" 1.250"
T-302 16" 1.438" ASTM A928 (UNS S31803 Cl 1 or 3) WLD
18" 1.562"
20" 1.750"
24" 2.062"
Weldolet C12-27 1" - 10" BE MSS SP-97 ASTM A182 Gr F51 (UNS S31803)
90 LR Elbow C15-29 -
45 LR Elbow C16-29
90 SR Elbow C17-29
Fittings
1" - 24"
Tee C20-29
According to pipe -
Cap C22-29 ASME B16.9 ASTM A815 (UNS S31803)
BE
Cross C24-29
Conc. Red C18-29
1 ½" - 24"
Ecc. Red C19-29
Red Tee C21-29 2" - 24"
Straight Nipple N-S228 1" - 1 ½" ASTM A733 ASTM A790 (UNS S31803)
Nipple
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
26 See Annex A for v alv e casting qualification requirements.
27 See Annex D to check the piping spec range application for H2S and CO2 serv ice.
29 For temperatures abov e 100°C, Duplex shall be coated acc. to I-ET-3010.00-1200-956-P4X-002 - General Painting.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
122 Inspection of pipe and piping components shall follow ASTM A923 requirements.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
1" - 12"
Tee C20-29
According to pipe -
Cap C22-29 ASME B16.9 ASTM A815 (UNS S31803)
BE
Cross C24-29
Conc. Red C18-29
1 ½" - 12"
Ecc. Red C19-29
Red Tee C21-29 2" - 12"
Straight Nipple N-S228 1" - 1 ½" ASTM A733 ASTM A790 (UNS S31803)
Nipple
Compact WN F-2500-UG
1" - 12" According to pipe Class 2500 IX seal ring ISO 27509 ASTM A182 Gr F51
Compact Blind F-2500-VG
Hyd One-Piece Flange F-420-3G 1" - 3" max 420 bar - ISO 6162-2
Ring-Joint J-2500-BU 1" - 12" - Class 2500 Metallic Seal Joint ISO 27509 Duplex , ASTM A182 F51
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
SOC - Sockolet
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
26 See Annex A for v alv e casting qualification requirements.
29 For temperatures abov e 100°C, Duplex shall be coated acc. to I-ET-3010.00-1200-956-P4X-002 - General Painting.
113 See table on item 8 for piping spec selection according to serv ice and application.
122 Inspection of pipe and piping components shall follow ASTM A923 requirements.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
127 ISO 6162-1/2 flanges may be used only for H - Hy draulic Fluid.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
2" - 3"
Pipe -
4" - 14" BE API 5L Gr X65 PSL 2 (SML or WLD SAW)
T-107 S-160 ASME B36.10
16" - 24" API 5L Gr X65 PSL 2 WLD SAW
Weldolet C12-33 BE MSS SP-97
90 LR Elbow C15-33 -
45 LR Elbow C16-33
90 SR Elbow C17-33 1" - 3" ASTM B366 (UNS N06625)
ASME B16.9
Tee C20-33
Cap C22-33
Cross C24-33 BE
Weldolet C12-22 1" - 10" MSS SP-97 ASTM A694 Gr F65
Conc. Red C18-33
Fittings
Ecc. Red C19-33 1 ½" - 3" ASME B16.9 ASTM B366 (UNS N06625)
According to pipe -
Red Tee C21-33
90 LR Elbow C15-22 -
45 LR Elbow C16-22
90 SR Elbow C17-22
Conc. Red C18-22
Ecc. Red C19-22 4" - 24" MSS SP-75 ASTM A860 WPHY65
BE
Tee C20-22
Red Tee C21-22
Cap C22-22
Cross C24-22
Straight Nipple N-S239 1" - 1 ½" ASTM A733 ASTM B444 Gr 1 (UNS N06625)
Nipple
Blind
F-2500-SD 4" - 12" ASTM A694 Gr F65 Cladded
According to pipe Class 2500
F-2500-UL 1" - 3" ASTM B564 (UNS N06625)
Compact WN
F-2500-UD 4" - 24" ASTM A694 Gr F65 Cladded
IX seal ring ISO 27509
F-2500-VL 1" - 3" ASTM B564 (UNS N06625)
Compact Blind
F-2500-VD 4" - 24" ASTM A694 Gr F65 Cladded
J-2500-AV 1" - 12" Ring Type Joint ASME B16.20
Bolts & Gasket
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
9 Charpy impact test is required at the minimum temperature of this spec, according to ASME B31.3 and API 5L requirements. Applicable to both base material and WPS qualification.
11 For API 5L pipe the max imum carbon equiv alent is CE iiw = 0,43% or CE pcm = 0,25%.
27 See Annex D to check the piping spec range application for H2S and CO2 serv ice.
42 Piping, fittings and acessories shall hav e internal Inconel® 625 cladding according to I-ET-3010.00-1200-955-P4X-001 - Welding.
70 Use this Spec only up to SDV.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.8 -
Blind
F-2500-SD 4" - 12" ASTM A694 Gr F65 Cladded
According to pipe Class 2500
F-2500-UL 1" - 3" ASTM B564 (UNS N06625)
Compact WN
F-2500-UD 4" - 20" ASTM A694 Gr F65 Cladded
IX seal ring ISO 27509
F-2500-VL 1" - 3" ASTM B564 (UNS N06625)
Compact Blind
F-2500-VD 4" - 20" ASTM A694 Gr F65 Cladded
J-2500-AV 1" - 12" Ring Type Joint ASME B16.20
Bolts & Gasket
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
9 Charpy impact test is required at the minimum temperature of this spec, according to ASME B31.3 and API 5L requirements. Applicable to both base material and WPS qualification.
11 For API 5L pipe the max imum carbon equiv alent is CE iiw = 0,43% or CE pcm = 0,25%.
27 See Annex D to check the piping spec range application for H2S and CO2 serv ice.
42 Piping, fittings and acessories shall hav e internal Inconel® 625 cladding according to I-ET-3010.00-1200-955-P4X-001 - Welding.
44 Only pipes NPS ≥ 4 are designed according to ASME B31.4/31.8.
67 Branches w ith diameter greater than or equal to half the nominal diameter of the pipe shall be fitted w ith guide bars according to DR-ENGP-I-1.14 – Standard Specification for Design of Pig L/R
71 Use this Spec only up to Pig Receiv ers.
77 The max imum reduction of w all thickness shall be 15% and 10% for 3d and 5d bends, respectiv ely .
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 1.6 mm
1" - 16"
Tee C20-24
According to pipe -
Cap C22-24 ASME B16.9 ASTM A420 Gr WPL8
BE
Cross C24-24
Conc. Red C18-24
Ecc. Red C19-24 1 ½" - 16"
Red Tee C21-24
Straight Nipple N-S223 1" - 1 ½" ASTM A733 ASTM A333 Gr 8
Nipple
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
98 Charpy impact test is required for low temperature serv ices materials in accordance w ith ASTM A 333.
99 Charpy impact test is required for low temperature serv ices materials in accordance w ith ASTM A 420.
100 Charpy impact test is required for low temperature serv ices materials in accordance w ith ASTM A 522.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 1.6 mm
Blind
F-2500-SK 4" - 12" ASTM A522 Type I Cladded
According to pipe Class 2500
F-2500-UL 1" - 3" ASTM B564 (UNS N06625)
Compact WN
F-2500-UD 4" - 12" ASTM A694 Gr F65 Cladded
IX seal ring ISO 27509
F-2500-VL 1" - 3" ASTM B564 (UNS N06625)
Compact Blind
F-2500-VD 4" - 12" ASTM A694 Gr F65 Cladded
J-2500-AV Ring Type Joint ASME B16.20
Bolts & Gasket
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
SOC - Sockolet
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
42 Piping, fittings and acessories shall hav e internal Inconel® 625 cladding according to I-ET-3010.00-1200-955-P4X-001 - Welding.
98 Charpy impact test is required for low temperature serv ices materials in accordance w ith ASTM A 333.
99 Charpy impact test is required for low temperature serv ices materials in accordance w ith ASTM A 420.
100 Charpy impact test is required for low temperature serv ices materials in accordance w ith ASTM A 522.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 1.6 mm
XXS
Pipe T-107 2" - 4" - ASME B36.10
BE API 5L Gr X65 PSL 2 (SML or WLD SAW)
6" 1.000"
Tee C20-22 1" MSS SP-75 ASTM A860 WPHY65
BE
Weldolet C12-22 1" - 2" MSS SP-97 ASTM A694 Gr F65
90 LR Elbow C15-22 -
45 LR Elbow C16-22
90 SR Elbow C17-22 1" - 4"
Cap C22-22 -
Cross C24-22
BE
Fittings
1 ½" - 4" According to pipe - BBE MSS SP-95 ASTM A860 WPHY65
Swage Ecc Nipple N-E222
Flange WN API 6BX F-10000-RC
1" - 6" According to pipe API 10000 Ring Type Joint 8110 ASTM A694 Gr F65
Blind API 6BX F-10000-SC
Ring-Joint J-10000-AN 1" - 6" - API 10000 Ring Type Joint API 6A Carbon Steel
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
HC - Half Coupling
SOC - Sockolet
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
27 See Annex D to check the piping spec range application for H2S and CO2 serv ice.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
4" 0.674"
Pipe - ASME B36.10/B36.19
6" 0.864"
BE
8" 1.125"
10" 1.250"
T-304 12" 1.438" ASTM A928 (UNS S32760 Cl 1 or 3) WLD
14" - 16" 2.000"
Weldolet C12-30 1" - 6" BE MSS SP-97 ASTM A182 Gr F55 (UNS S32760)
90 LR Elbow C15-32 -
45 LR Elbow C16-32
90 SR Elbow C17-32
Fittings
1" - 16"
Tee C20-32
According to pipe -
Cap C22-32 ASME B16.9 ASTM A815 (UNS S32760)
BE
Cross C24-32
Conc. Red C18-32
Ecc. Red C19-32 1 ½" - 16"
Red Tee C21-32
Straight Nipple N-S231 1" - 1 ½" ASTM A733 ASTM A790 (UNS S32760)
Bolts & Gasket Flanges Nipple
Ring-Joint J-10000-AU 1" - 16" - API 10000 Ring Type Joint API 6A Duplex , ASTM A182 F51
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
27 See Annex D to check the piping spec range application for H2S and CO2 serv ice.
48 For temperatures abov e110°C, Superduplex shall be coated acc. to I-ET-3010.00-1200-956-P4X-002 - General Painting.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
122 Inspection of pipe and piping components shall follow ASTM A923 requirements.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.8 -
4" 0.531"
Pipe - ASME B36.10/B36.19
6" 0.750"
BE
8" 1.000"
10" 1.250"
T-304 12" 1.406" ASTM A928 (UNS S32760 Cl 1 or 3) WLD
14" 2.000"
90 LR Elbow C15-32 -
45 LR Elbow C16-32 1" - 3" ASME B16.9 ASTM A815 (UNS S32760)
90 SR Elbow C17-32
Weldolet C12-30 1" - 6" MSS SP-97 ASTM A182 Gr F55 (UNS S32760)
Tee C20-32
Cap C22-32 1" - 14"
Cross C24-32
ASME B16.9 ASTM A815 (UNS S32760)
Conc. Red C18-32
Fittings
1 ½" - 3"
Ecc. Red C19-32
According to pipe -
Red Tee C21-32 1 ½" - 14" BE
3D 45 Bend C33-31
5D 45 Bend C34-31
4" - 8" ASTM A790 (UNS S32760)
3D 90 Bend C35-31
5D 90 Bend C36-31
according to manufacturer
3D 45 Bend C33-41
5D 45 Bend C34-41
10" - 14" ASTM A928 (UNS S32760 Cl 1 or 3)
3D 90 Bend C35-41
5D 90 Bend C36-41
Straight Nipple N-S231 1" - 1 ½" ASTM A733 ASTM A790 (UNS S32760)
Bolts & Gasket Flanges Nipple
Ring-Joint J-10000-AU 1" - 14" - API 10000 Ring Type Joint API 6A Duplex , ASTM A182 F51
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
SOC - Sockolet
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
27 See Annex D to check the piping spec range application for H2S and CO2 serv ice.
44 Only pipes NPS ≥ 4 are designed according to ASME B31.4/31.8.
48 For temperatures abov e110°C, Superduplex shall be coated acc. to I-ET-3010.00-1200-956-P4X-002 - General Painting.
67 Branches w ith diameter greater than or equal to half the nominal diameter of the pipe shall be fitted w ith guide bars according to DR-ENGP-I-1.14 – Standard Specification for Design of Pig L/R
77 The max imum reduction of w all thickness shall be 15% and 10% for 3d and 5d bends, respectiv ely .
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
122 Inspection of pipe and piping components shall follow ASTM A923 requirements.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 1.6 mm
Ring-Joint J-10000-AT 1" - 16" - API 10000 Ring Type Joint API 6A Stainless Steel AISI 316
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
98 Charpy impact test is required for low temperature serv ices materials in accordance w ith ASTM A 333.
99 Charpy impact test is required for low temperature serv ices materials in accordance w ith ASTM A 420.
100 Charpy impact test is required for low temperature serv ices materials in accordance w ith ASTM A 522.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.8 1.6 mm
XXS
Pipe T-201 2" - 6" - ASME B36.10 ASTM A333 Gr 8 SML
BE
8" 1.125"
Weldolet C12-25 BE MSS SP-97 ASTM A522 Type I
90 LR Elbow C15-24 -
45 LR Elbow C16-24 1" - 3"
90 SR Elbow C17-24
Cross C24-24
Tee C20-24 ASME B16.9 ASTM A420 Gr WPL8
Fittings
1" - 8"
Cap C22-24
According to pipe -
Conc. Red C18-24
1 ½" - 3" BE
Ecc. Red C19-24
Red Tee C21-24 1 ½" - 8"
3D 45 Bend C33-23
5D 45 Bend C34-23
4" - 8" according to manufacturer ASTM A333 Gr 8
3D 90 Bend C35-23
5D 90 Bend C36-23
Bolts & Gasket Flanges Nipple
Straight Nipple N-S223 1" - 1 ½" According to pipe - BBE ASTM A733 ASTM A333 Gr 8
Ring-Joint J-10000-AT 1" - 8" - API 10000 Ring Type Joint API 6A Stainless Steel AISI 316
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
HC - Half Coupling
SOC - Sockolet
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
44 Only pipes NPS ≥ 4 are designed according to ASME B31.4/31.8.
67 Branches w ith diameter greater than or equal to half the nominal diameter of the pipe shall be fitted w ith guide bars according to DR-ENGP-I-1.14 – Standard Specification for Design of Pig L/R
77 The max imum reduction of w all thickness shall be 15% and 10% for 3d and 5d bends, respectiv ely .
98 Charpy impact test is required for low temperature serv ices materials in accordance w ith ASTM A 333.
99 Charpy impact test is required for low temperature serv ices materials in accordance w ith ASTM A 420.
100 Charpy impact test is required for low temperature serv ices materials in accordance w ith ASTM A 522.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
4" 0.531"
Pipe T-203 - ASME B36.10/B36.19 ASTM B444 Gr 1 (UNS N06625) SML
6" 0.864"
BE
8" 1.062"
10" 1.250"
12" 1.594"
14" 1.781"
Weldolet C12-33 1" - 6" BE MSS SP-97
90 LR Elbow C15-33 -
45 LR Elbow C16-33
90 SR Elbow C17-33
Fittings
1" - 14"
Tee C20-33
According to pipe - ASTM B366 (UNS N06625)
Cap C22-33 ASME B16.9
BE
Cross C24-33
Conc. Red C18-33
Ecc. Red C19-33 1 ½" - 14"
Red Tee C21-33
Straight Nipple N-S239 1" - 1 ½" ASTM A733 ASTM B444 Gr 1 (UNS N06625)
Bolts & Gasket Flanges Nipple
Ring-Joint J-10000-AV 1" - 14" - API 10000 Ring Type Joint API 6A Inconel
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
SOC - Sockolet
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
101 Charpy impact test is required for low temperature serv ices materials in accordance w ith ASTM B 444.
102 Charpy impact test is required for low temperature serv ices materials in accordance w ith ASTM B 564.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
4" 0.531"
Pipe T-203 - ASME B36.10/B36.19 ASTM B444 Gr 1 (UNS N06625) SML
6" 0.864"
BE
8" 1.062"
10" 1.250"
12" 1.594"
14" 1.781"
90 LR Elbow C15-33 -
45 LR Elbow C16-33 1" - 3" ASME B16.9
90 SR Elbow C17-33
Weldolet C12-33 1" - 6" MSS SP-97
Tee C20-33
ASTM B366 (UNS N06625)
Cap C22-33 1" - 14"
Fittings
Cross C24-33
According to pipe - ASME B16.9
Conc. Red C18-33 BE
1 ½" - 3"
Ecc. Red C19-33
Red Tee C21-33 1 ½" - 14"
3D 45 Bend C33-39
5D 45 Bend C34-39
4" - 14" according to manufacturer ASTM B444 Gr 1 (UNS N06625)
3D 90 Bend C35-39
5D 90 Bend C36-39
Straight Nipple N-S239 1" - 1 ½" ASTM A733 ASTM B444 Gr 1 (UNS N06625)
Bolts & Gasket Flanges Nipple
Ring-Joint J-10000-AV 1" - 14" - API 10000 Ring Type Joint API 6A Inconel
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
SOC - Sockolet
Notes
1 On the spec v alv e list, it may hav e v alv es codes w hich contain v alues of process data low er than spec limits. It shall be v erified all v alv e process data (e.g.: pressure, temperature) in order to
specify it according the design premisses.
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
4 See Annex C for instruments, drains and v ents ty pical piping arrangement.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary .
6 See Annex E for Isolation gasket specifications.
7 Welding and Welding Inspection activ ities shall follow the requeriments of these documents: I-ET-3010.00-1200-955-P4X-001-Welding and I-ET-3010.00-1200-955-P4X-002-Requirements for
Welding Inspection
8 All v alv es, pipes and components specified for hy drogen sulfide serv ice shall be in accordance w ith ISO 15156 requirements.
67 Branches w ith diameter greater than or equal to half the nominal diameter of the pipe shall be fitted w ith guide bars according to DR-ENGP-I-1.14 – Standard Specification for Design of Pig L/R
77 The max imum reduction of w all thickness shall be 15% and 10% for 3d and 5d bends, respectiv ely .
101 Charpy impact test is required for low temperature serv ices materials in accordance w ith ASTM B 444.
102 Charpy impact test is required for low temperature serv ices materials in accordance w ith ASTM B 564.
120 Wafer v alv es are not to be used w ith flamable or combustible serv ices, according to NFPA definition.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
S-80S
Pipe 2" -
T-323 BE ASME B36.10/B36.19 ASTM A358 Type 316/316L Cl 1 or 3 WLD
3" - 6" S-40S
45 Elbow GMC Type I C70-43
Fittings
Blind F-150-LX
¾" - 6" According to pipe Class 150 Raised Face ASME B16.5 ASTM A182 Gr F316/316L
Flange GMC Type I F-150-5X
Spiral-Wound J-150-EH ¾" - 6" - Class 150 Raised Face ASME B16.20 AISI 316/graphite
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
SOC - Sockolet
Notes
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
91 Specific tools shall be used to assembly piping fittings, therefore is mandatory manufacturer assistance.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
S-80S
Pipe 2" -
T-323 BE ASME B36.10/B36.19 ASTM A358 Type 316/316L Cl 1 or 3 WLD
3" - 6" S-40S
45 Elbow GMC Type I C70-43
Fittings
Blind F-300-LX
¾" - 6" According to pipe Class 300 Raised Face ASME B16.5 ASTM A182 Gr F316/316L
Flange GMC Type I F-300-5X
Spiral-Wound J-300-EH ¾" - 6" - Class 300 Raised Face ASME B16.20 AISI 316/graphite
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
SOC - Sockolet
Notes
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
91 Specific tools shall be used to assembly piping fittings, therefore is mandatory manufacturer assistance.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 1.6 mm
Pipe T-102 - ASME B36.10 API 5L Gr B PSL 1 (SML or WLD HFW or WLD
2" - 6" XS BE SAW)
45 Elbow GMC Type I C70-02
Fittings
Blind F-150-L2
¾" - 6" According to pipe Class 150 Raised Face ASME B16.5 ASTM A105
Flange GMC Type I F-150-52
Spiral-Wound J-150-EH ¾" - 6" - Class 150 Raised Face ASME B16.20 AISI 316/graphite
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
SOC - Sockolet
Notes
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
91 Specific tools shall be used to assembly piping fittings, therefore is mandatory manufacturer assistance.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 1.6 mm
Pipe T-102 - ASME B36.10 API 5L Gr B PSL 1 (SML or WLD HFW or WLD
2" - 6" XS BE SAW)
45 Elbow GMC Type I C70-02
Fittings
Blind F-300-L2 ¾" - 6" According to pipe Class 300 Raised Face ASME B16.5 ASTM A105
Spiral-Wound J-300-EH ¾" - 6" - Class 300 Raised Face ASME B16.20 AISI 316/graphite
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
SOC - Sockolet
Notes
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
91 Specific tools shall be used to assembly piping fittings, therefore is mandatory manufacturer assistance.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
Pipe T-322 ½" - 1 ½" S-40S - PE ASME B36.19 ASTM A312 TP 316/316L SML
Spiral-Wound J-150-EH ½" - 2" - Class 150 Raised Face ASME B16.20 AISI 316/graphite
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
HC - Half Coupling
SOC - Sockolet
Notes
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
91 Specific tools shall be used to assembly piping fittings, therefore is mandatory manufacturer assistance.
96 Fittings accordig to ASTM F1387 - Standard Specification for Performance of Piping and Tubing Mechanically Attached Fittings.
97 Epox y resins or similar shall be applied in the gap betw een pipings and fittings, to av oid crev ice corrosion.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
Pipe T-322 ½" - 1 ½" S-40S - PE ASME B36.19 ASTM A312 TP 316/316L SML
Spiral-Wound J-300-EH ½" - 2" - Class 300 Raised Face ASME B16.20 AISI 316/graphite
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
HC - Half Coupling
SOC - Sockolet
Notes
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
91 Specific tools shall be used to assembly piping fittings, therefore is mandatory manufacturer assistance.
96 Fittings accordig to ASTM F1387 - Standard Specification for Performance of Piping and Tubing Mechanically Attached Fittings.
97 Epox y resins or similar shall be applied in the gap betw een pipings and fittings, to av oid crev ice corrosion.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
Flat type J-150-PA ½" - 2" - Class 150 Raised Face ASME B16.21 Aramid/NBR
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
HC - Half Coupling
SOC - Sockolet
Notes
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
85 The thicknesses listed in this spec are minimum and shall be confirmed by fittings supplier in order to garantee the correct assembly .
91 Specific tools shall be used to assembly piping fittings, therefore is mandatory manufacturer assistance.
96 Fittings accordig to ASTM F1387 - Standard Specification for Performance of Piping and Tubing Mechanically Attached Fittings.
97 Epox y resins or similar shall be applied in the gap betw een pipings and fittings, to av oid crev ice corrosion.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 1.6 mm
Swage Conc Nipple N-C602 ¾" - 2" According to pipe - MAF ASTM F1387 ASTM A105
Spiral-Wound J-150-EH ½" - 2" - Class 150 Raised Face ASME B16.20 AISI 316/graphite
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
HC - Half Coupling
SOC - Sockolet
Notes
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
91 Specific tools shall be used to assembly piping fittings, therefore is mandatory manufacturer assistance.
96 Fittings accordig to ASTM F1387 - Standard Specification for Performance of Piping and Tubing Mechanically Attached Fittings.
97 Epox y resins or similar shall be applied in the gap betw een pipings and fittings, to av oid crev ice corrosion.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 1.6 mm
Swage Conc Nipple N-C602 ¾" - 2" According to pipe - MAF ASTM F1387 ASTM A105
Spiral-Wound J-300-EH ½" - 2" - Class 300 Raised Face ASME B16.20 AISI 316/graphite
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
HC - Half Coupling
SOC - Sockolet
Notes
2 See Annex A for v alv es requirements and general selection criteria.
3 Bolts,nuts and gaskets (only RTJ gaskets) must be Zn-Ni coated according to Annex B.
91 Specific tools shall be used to assembly piping fittings, therefore is mandatory manufacturer assistance.
96 Fittings accordig to ASTM F1387 - Standard Specification for Performance of Piping and Tubing Mechanically Attached Fittings.
97 Epox y resins or similar shall be applied in the gap betw een pipings and fittings, to av oid crev ice corrosion.
125 Materials shall follow the requirements of IOGP S-563- Material Data Sheets for Piping and Valv e Components. Coating for bolts and nuts shall follow spec note number 3.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
OD x OD
Compression Fitting C60-40 ¼" - 1 ½" - 6000 OD x THD according to manufacturer Compression fitting with double ferrule, body AISI
316, ferrules and nuts in AISI 316.
OD x SW
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
SOC - Sockolet
Notes
2 See Annex A for v alv es requirements and general selection criteria.
72 Tubing rods shall be prov ided w ith a standard 6-meter length. Coiled tubings are not acceptable
76 Tube fittings shall hav e the manufacturer's name and the traceability code indelibly engrav ed. Ferrules may hav e only the manufacturer's name engrav ed.
78 Tube fittings shall be double ferrule ty pe.
81 The tubing shall be prepared (cut, burred, and bent) only w ith the tools recommended by the OD fittings manufacturer.
84 The tube material specification EN 1.4435 may be used instead of ASTM A269 316L
88 The minimum Moly bdenum content shall be 2,5% for tubing material.
89 The max imum w ork pressure for fittings shall be abov e the max imum w ork pressure of the tubing for all operation conditions.
93 Seal or fillet w elds are not allow ed in OD fittings and v alv es assembly .
95 Proper tools shall be used to assemble the OD fittings (feeler gauge, w renches etc.) in accordance w ith the fittings' manufacture instructions . Special attention shall be giv en for assemblies w ith
OD 1" and larger w here presw age must be done.
124 The max imum pressure of a sy stem w ith sev eral diameters is limited by the low est pressure according to the spec pressure table.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
SOC - Sockolet
Notes
2 See Annex A for v alv es requirements and general selection criteria.
72 Tubing rods shall be prov ided w ith a standard 6-meter length. Coiled tubings are not acceptable
76 Tube fittings shall hav e the manufacturer's name and the traceability code indelibly engrav ed. Ferrules may hav e only the manufacturer's name engrav ed.
78 Tube fittings shall be double ferrule ty pe.
81 The tubing shall be prepared (cut, burred, and bent) only w ith the tools recommended by the OD fittings manufacturer.
84 The tube material specification EN 1.4435 may be used instead of ASTM A269 316L
88 The minimum Moly bdenum content shall be 2,5% for tubing material.
89 The max imum w ork pressure for fittings shall be abov e the max imum w ork pressure of the tubing for all operation conditions.
93 Seal or fillet w elds are not allow ed in OD fittings and v alv es assembly .
95 Proper tools shall be used to assemble the OD fittings (feeler gauge, w renches etc.) in accordance w ith the fittings' manufacture instructions . Special attention shall be giv en for assemblies w ith
OD 1" and larger w here presw age must be done.
124 The max imum pressure of a sy stem w ith sev eral diameters is limited by the low est pressure according to the spec pressure table.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 1 of 2
Issued by : Code: Corr. Allow .:
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES SRGE/ESUP ASME B31.3 -
OD x THD
Compression Fitting C60-47 ⅝" - 10000 OD x SW according to manufacturer Compression fitting with double ferrule,
body/nut/ferrule SuperDuplex UNS 32760
OD x OD
OD x THD
¾" OD x SW
OD x OD
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
Doc: Rev ision: Sheet:
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES DR-ENGP-I-1.1 11 2 of 2
HC - Half Coupling
SOC - Sockolet
Notes
2 See Annex A for v alv es requirements and general selection criteria.
72 Tubing rods shall be prov ided w ith a standard 6-meter length. Coiled tubings are not acceptable
76 Tube fittings shall hav e the manufacturer's name and the traceability code indelibly engrav ed. Ferrules may hav e only the manufacturer's name engrav ed.
78 Tube fittings shall be double ferrule ty pe.
81 The tubing shall be prepared (cut, burred, and bent) only w ith the tools recommended by the OD fittings manufacturer.
89 The max imum w ork pressure for fittings shall be abov e the max imum w ork pressure of the tubing for all operation conditions.
93 Seal or fillet w elds are not allow ed in OD fittings and v alv es assembly .
95 Proper tools shall be used to assemble the OD fittings (feeler gauge, w renches etc.) in accordance w ith the fittings' manufacture instructions . Special attention shall be giv en for assemblies w ith
OD 1" and larger w here presw age must be done.
124 The max imum pressure of a sy stem w ith sev eral diameters is limited by the low est pressure according to the spec pressure table.
THIS DOCUMENT IS PROPERTY OF PETROBRAS, BEING ITS USE PROHIBITED OUTSIDE ITS PURPOSE
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
ANNEX A – VALVES
(Mandatory)
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
INDEX
A.1. SCOPE .....................................................................................................................................5
A.2. NORMATIVE REFERENCES ...................................................................................................5
A.3. TERMS AND DEFINITIONS .....................................................................................................7
A.4. SYMBOLS AND ABBREVIATED TERMS ...............................................................................9
A.5. VALVE SELECTION GUIDE ..................................................................................................10
A.5.1. INTRODUCTION ..................................................................................................................................................10
A.5.2. VALVE SPECIFICATION LEVEL (VSL) - CLASSIFICATION .............................................................................11
A.5.3. VALVE SPECIFICATION LEVEL (VSL) - REQUIREMENTS ..............................................................................12
A.5.4. VALVE FEATURES AND TYPICAL APLICATIONS ............................................................................................13
A.6. GENERAL DESIGN REQUIREMENTS ..................................................................................15
A.6.1. VALVE ..................................................................................................................................................................15
A.6.2. ACTUATOR ..........................................................................................................................................................22
A.7. SPECIFIC DESIGN REQUIREMENTS ...................................................................................23
A.7.1. BALL VALVE ........................................................................................................................................................23
A.7.2. GATE VALVE .......................................................................................................................................................39
A.7.3. CHECK VALVE ....................................................................................................................................................42
A.7.4. GLOBE VALVE ....................................................................................................................................................45
A.7.5. BUTTERFLY VALVE ............................................................................................................................................47
A.7.6. NON-METALLIC VALVE ......................................................................................................................................50
A.8. MATERIALS & FABRICATION ..............................................................................................52
A.8.1. REQUIREMENTS FOR CASTING OF DUPLEX & SUPERDUPLEX ..................................................................52
A.8.2. COATINGS ...........................................................................................................................................................57
A.8.3. ALTERNATIVE MATERIALS ...............................................................................................................................60
A.9. INSPECTION & TESTING ......................................................................................................61
A.9.1. INSPECTION REQUIREMENTS .........................................................................................................................61
A.9.2. DESIGN VALIDATION .........................................................................................................................................63
A.9.3. FACTORY ACCEPTANCE TEST (FAT) REQUIREMENTS ................................................................................64
A.10. HANDLING, STORING & SHIPPING..................................................................................69
A.11. DOCUMENTATION .............................................................................................................70
A.11.1. DOCUMENTATION FORMATS & QUALITY .....................................................................................................70
A.11.2. DATA BOOK ......................................................................................................................................................70
A.11.3. USER MANUAL .................................................................................................................................................71
A.11.4. DOCUMENTATION OF PRESERVATION, PROTECTION AND PACKING ....................................................71
A.11.5. VALVE CODE ....................................................................................................................................................72
A.12. VALVE DATASHEET - VDS ...............................................................................................79
- Rev. 11 - Page 2 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
FIGURES
FIGURE A.1 – EXAMPLE OF USE OF DRAIN AND VENT PLUG ............................................................................................................................ 15
FIGURE A.2 – EXAMPLE OF NAMEPLATES WITH INDICATION OF SEAT CONFIGURATION ............................................................................. 21
FIGURE A.3 - LOCATION OF DRAIN AND VENT PORTS ....................................................................................................................................... 24
FIGURE A.4 – BALL TYPE ....................................................................................................................................................................................... 24
FIGURE A.5 – SPE/SR SEAT ASSEMBLY MECHANISM (ILLUSTRATION ON A SOFT BALL VALVE) .................................................................. 26
FIGURE A.6 – DPE SEAT ASSEMBLY MECHANISM (ILLUSTRATION ON A SOFT BALL VALVE) ........................................................................ 26
FIGURE A.7 – DBB FEATURE (REF.: DOUBLE BLOCK AND BLEED - TYPE B OF API 6D) .................................................................................. 27
FIGURE A.8 – DIB-1 FEATURE (REF.: DOUBLE ISOLATION AND BLEED - TYPE B OF API 6D) .......................................................................... 27
FIGURE A.9 – DIB-2 FEATURE (REF.: DOUBLE ISOLATION AND BLEED - TYPE B OF API 6D) .......................................................................... 27
FIGURE A.10 – ILLUSTRATION OF TYPICAL CATEGORY B (TRIPLE OFFSET) SEAT CONFIGURATIONS ........................................................ 48
TABLES
TABLE A.1 – CLASSIFICATION OF ACCUMULATED ENERGY AND HIGH DEMAND VALVES ............................................................................. 12
TABLE A.2 – VALVE SPECIFICATION LEVEL (VSL) CLASSIFICATION ................................................................................................................. 12
TABLE A.3 – VALVE SPECIFICATION LEVEL (VSL) REQUIREMENTS .................................................................................................................. 13
TABLE A.4 - VALVE FEATURES AND TYPICAL APPLICATIONS ........................................................................................................................... 14
TABLE A.5 – MATERIAL CLASSES ......................................................................................................................................................................... 16
TABLE A.6 – BODY MATERIAL, ACCORDING TO MATERIAL CLASS ................................................................................................................... 16
TABLE A.7 – PROCESS FABRICATION FOR BODY MATERIALS ACCORDING TO VSL ...................................................................................... 17
TABLE A.8 – TIGHTNESS CLASS FOR STEM SEALS - FUGITIVE EMISSIONS (REF.: ISO 15848 PART 1) ......................................................... 18
TABLE A.9 – TIGHTNESS CLASS FOR BODY SEALS - FUGITIVE EMISSIONS (REF.: ISO 15848 PART 1) ......................................................... 18
TABLE A.10 – TIGHTNESS CLASS FOR STEM (OR SHAFT) SEALS WITH METHANE - FUGITIVE EMISSIONS (REF.: ISO 15848 PART 1) ...... 19
TABLE A.11 – LEAKAGE FROM BODY SEALS WITH METHANE - FUGITIVE EMISSIONS (REF.: ISO 15848 PART 1) ........................................ 19
TABLE A.12 – ENDURANCE CLASS ACCORDING VSL CLASSIFICATION ........................................................................................................... 19
TABLE A.13 – TEMPERATURE CLASS OF FUGITIVE EMISSIONS (REF.: ISO 15848 PART 1) ............................................................................ 19
TABLE A.14 – SIL LEVELS ...................................................................................................................................................................................... 19
TABLE A.15 - STUDS, BOLTS AND NUTS MATERIAL SPECIFICATION ................................................................................................................ 20
TABLE A.16 – ACTUATORS TYPE .......................................................................................................................................................................... 22
TABLE A.17 – DESIGN STANDARDS FOR BALL VALVES ..................................................................................................................................... 25
TABLE A.18 – MOUNTING TYPE FOR BALL VALVES ............................................................................................................................................ 25
TABLE A.19 – ISOLATION VALVE CONFIGURATION FOR BALL VALVES ............................................................................................................ 28
TABLE A.20 – NON-METALLIC MATERIALS FOR SEAT INSERT SEAL DESIGN .................................................................................................. 28
TABLE A.21 – SEAL GROUPS MATERIALS ............................................................................................................................................................ 29
TABLE A.22 – INDICATION OF GROUPS OF SEALS ACCORDING FLUID CLASS AND TEMPERATURE RANGE .............................................. 30
TABLE A.23 – SEALS GROUP CLASSIFICATION INTO VALVE CODE .................................................................................................................. 30
TABLE A.24 – NIPPLE CLASSIFICATION INTO VALVE CODE ............................................................................................................................... 31
TABLE A.25 – TYPICAL CONFIGURATIONS FOR BALL VALVES UP TO NPS 1 1/2 (“FORGED” VALVES) .......................................................... 31
TABLE A.26 – TYPICAL CONFIGURATIONS FOR BALL VALVES NPS 2 AND ABOVE ......................................................................................... 32
TABLE A.27 – TYPICAL CONFIGURATIONS FOR RISING STEM BALL VALVES .................................................................................................. 33
TABLE A.28 – TYPICAL CONFIGURATIONS FOR DOUBLE BALL VALVES........................................................................................................... 33
TABLE A.29 - STEM MATERIALS ACCORDING MATERIAL CLASS & PRESSURE CLASS OF THE VALVE......................................................... 34
TABLE A.30 – SPECIFICATION OF METALLIC COATING (PARTIAL CLAD) FOR BALL VALVES ......................................................................... 35
TABLE A.31 – SPECIFICATION OF HARD COATING ON SEATS / BALL ON SOFT BALL VALVES ...................................................................... 35
TABLE A.32 – SPECIFICATION OF HARD COATING ON SEATS / BALL ON METAL TO METAL BALL VALVES ................................................. 36
TABLE A.33 – TYPICAL CONFIGURATIONS FOR SOFT SEATED BALL VALVES ACCORDING MATERIAL CLASS ........................................... 36
TABLE A.34 – TYPICAL CONFIGURATIONS FOR METAL TO METAL SEATED BALL VALVES ACCORDING MATERIAL CLASS ...................... 38
- Rev. 11 - Page 3 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
- Rev. 11 - Page 4 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
A.1. SCOPE
The scope of this document is related to axial, ball, butterfly, check, diaphragm, gate, globe, needle and plug valves,
either manually actuated or operated by actuators, for use in Exploration and Production (E&P) business area, onshore
and offshore, especially in oil and gas production and their process facilities.
This document specifies requirements for valves concerning the following topics: design, performance, materials,
manufacturing, testing, inspection, marking, handling, storing, shipment and documentation.
This document is not applicable to control valves. DR-ENGP-I-1.5 addresses main requirements for control valves and
also stablishes supplementary requirements for emergency Shut Down Valves (SDV) and BlowDown Valves (BDV).
The valves considered in this document may be acquired directly by PETROBRAS or through a Contract, as example
EPC (Engineering, Procurement and Construction), in both cases to be used for existing facilities or new projects.
API 600, Steel Gate Valves-Flanged and Butt-Welding Ends, Bolted Bonnets
API 602, Steel Gate, Globe and Check Valves for Sizes DN 100 and Smaller for the Petroleum and Natural Gas
Industries
API 607, Fire Test for Quarter-turn Valves and Valves Equipped with Nonmetallic Seats
ASME B 1.1, Unified Inch Screw Threads, UN and UNR Thread Form
ASME B 18.2.1, Square, Hex, Heavy Hex, and Askew Head Bolts and Hex, Heavy Hex, Hex Flange, Lobed Head, and
Lag Screws (Inch Series)
ASME B 18.2.2, Nuts for General Applications: Machine Screw Nuts, Hex, Square, Hex Flange, and Coupling Nuts (Inch
Series)
ASME B16.1, Gray Iron Pipe Flanges and Flanged Fittings: Classes 25, 125, and 250
ASME B16.20, Metallic Gaskets for Pipe Flanges: Ring-Joint, Spiral-Wound, and Jacketed
- Rev. 11 - Page 5 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
ASME B16.47, Large Diameter Steel Flanges: NPS 26 through NPS 60 Metric/Inch Standard
ASME B16.5, Pipe Flanges and Flanged Fittings: NPS 1/2 through NPS 24 Metric/Inch Standard
ASME B31.4, Pipeline Transportation Systems for Liquid Hydrocarbons and Other Liquids
ASME SA–995–04, Specification for Castings, Austenitic-Ferritic (Duplex) Stainless Steel, for Pressure-Containing Parts
ASME SEC VIII DIV 1 SUB A PT UG, General Requirements for All Methods of Construction and All Materials
ASME Section II, Part D, Boiler and Pressure Vessel Code (BPVC), Section II: Materials – Part D: Properties (Metric)
ASME Section VIII, Division 1, Boiler and Pressure Vessel Code (BPVC), Section VIII, Division 1: Rules for Construction
of Pressure Vessels
ASME Section VIII, Division 2, 2004 Edition, Boiler and Pressure Vessel Code, Section VIII, Division 2: Alternative Rules
ASTM A370–05, Test Methods and Definitions for Mechanical Testing of Steel Products
ASTM A488 / A488M–04, Steel Castings, Welding, Qualifications of Procedures and Personnel
ASTM A703 /A703M–04A, Steel Castings, General Requirements, for Pressure-Containing Parts
ASTM A781 / A781M–05, Castings, Steel and Alloy, Common Requirements, for General Industrial Use
ASTM A802 / A802M–95, Steel Castings, Surface Acceptance Standards, Visual Examination
ASTM A903 / A903M–99, Steel Castings, Surface Acceptance Standards, Magnetic Particle and Liquid Penetrant
Inspection
ASTM A995 / A995M–98, Specification for Castings, Austenitic-Ferritic (Duplex) Stainless Steel, for Pressure-Containing
Parts
ASTM B584, Specification for copper alloy sand castings for general applications
ASTM B849, Specification for pre-treatments of iron or steel for reducing risk of hydrogen embrittlement
ASTM B850, Standard Guide for post-coating treatments of steel for reducing the risk of hydrogen embrittlement
ASTM E562–02, Test Method for Determining Volume Fraction by Systematic Manual Point Count
ASTM G48–03, Standard Test Method for Pitting and Crevice Corrosion Resistance of Stainless Steel and Related
Alloys by Use of Ferric Chloride Solution
BS 1868, Specification for steel check valves (flanged and butt-welding ends) for the petroleum, petrochemical and allied
industries
- Rev. 11 - Page 6 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
BS 1873, Specification for steel globe and globe stop and check valves (flanged and butt-welding ends) for the
petroleum, petrochemical and allied industries
BS EN 1226 6-1, Industrial valves – Testing of metallic valves Part 1: Pressure tests, test procedures and acceptance
criteria – Mandatory requirements
BS EN 12266-2, Industrial valves – Testing of metallic valves Part 2: Tests, test procedures and acceptance criteria –
Supplementary requirements
BS ISO 7121, Steel Ball Valves for general purpose Industrial Applications
IOGP S-611, Supplementary Requirements to API 600 Steel Gate Valves and to API 603 CRA Gate Valves
ISO 10434, Bolted bonnet steel gate valves for the petroleum, petrochemical and allied industries
ISO 12944-9, Paints and varnishes — Corrosion protection of steel structures by protective paint systems
ISO 14313, Petroleum and natural gas industries – Pipeline transportation systems – Pipeline valves
ISO 15156 (all parts), Petroleum and natural gas industries - Materials for use in H2S-containing environments in oil and
gas production
ISO 15761, Steel gate, globe and check valves for sizes DN 100 and smaller, for the petroleum and natural gas industries
ISO 15848-1, Industrial valves - Measurement, test and qualification procedures for fugitive emissions – Part 1:
Classification system and qualification procedures for type testing of valves
ISO 15848-2, Industrial valves - Measurement, test and qualification procedures for fugitive emissions – Part 2:
Production acceptance test of valves
ISO 17292, Metal ball valves for petroleum, petrochemical and allied industries
MSS SP-25, Standard Marking System for Valves, Fittings, Flanges and Unions
MSS SP-55, Quality Standard for Steel Castings for Valves, Flanges, Fittings, and Other Piping Components - Visual
Method for Evaluation of Surface Irregularities
MSS SP-9, Spot facing for bronze, iron and steel flanges
NBR 15827, Industrial Valves for Installations of Exploration, Production, Refining and Transport of Petroleum Products
- Requirements for Design and Prototype Test
- Rev. 11 - Page 7 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
Valve designed for blocking the fluid in both downstream and upstream directions.
The regions of castings determined by manufacturer engineering, based on valve parts highly stressed by manufacturing
process and as determined by finite elements under the maximum process/operating conditions.
Single valve with two seating surfaces that, in the closed position, provides a seal against pressure from both ends of
the valve with a means of venting/bleeding the cavity between the seating surfaces.
Single valve with two seating surfaces, each of which, in the closed position, provides a seal against pressure from a
single source, with a means of venting/bleeding the cavity between the seating surfaces.
DIB-1 valves have both seats bidirectional. Vent or relief of valve cavity shall be obtained by use of an external relief
valve.
DIB-2 valves have one seat unidirectional and one seat bidirectional. Further details are listed in A.7.1.4.
Valve with an uninterrupted and continuous cylindrical opening. Consequently, there are no cavities or large gaps in the
bore between seats and body closures or between seats and obturator.
Valve with an unobstructed opening, not smaller than the internal bore of the end connections.
Contact surfaces of the obturator and seat which ensure valve sealing.
Numerical pressure design class, expressed in accordance with either the nominal pressure (PN) class or the ASME
rating class.
Empiric Mathematical Formula that correlates pitting corrosion resistance with the amounts alloying elements in the steel
that contribute to increase this resistance. For duplex steels it shall be calculated as follows:
For the customer purpose, any casting that is the first of its model or of a new or modified project, using the same casting
procedure (same casting) as the ones it represents.
A.3.11. CASTING:
- Rev. 11 - Page 8 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
It is the actual value of torque needed to operate the valve, under any operation condition. This value shall be presented
in the marking (plate) of the valve.
It is the maximum value of torque that may be applied on the valve, without damaging the override mechanism (i.e.: no
plastic deformation on the drive train). This value of torque shall present the safety margin of the actuator, to be applied
only under special situation such as a contingency (e.g.: when the valve is not opening / closing with TNO value).
Typically, TMO is 150% TNO.
It is the value of torque that may be applied on the valve, after that it shall start damaging the override mechanism (i.e.:
plastic deformation on the drive train).
DIB-2 double isolation and bleed. One seat uni-directional (SPE or SR) and one seat bidirectional (DPE)
DN nominal size
HP high pressure
ID internal diameter
LP low pressure
- Rev. 11 - Page 9 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
SR self-relief
A.5.1.1. In this item is presented general information, such as a guide of how shall be conducted the engineering process
to select a valve for use in the Project and/or specific application.
- Rev. 11 - Page 10 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
A.5.1.2. The indication of all valves shall be driven by the definition of Valve Specification Level (VSL), which regulates
the specification of an adequate valve for a certain application, taking into account the criticality foreseen in the
application/use of the valve.
A.5.1.3. The VSL classification will provide specific requirements for four valve specification levels (VSLs): VSL-1,
VSL- 2, VSL-3, VSL-4. These four VSL designations define different levels of technical / quality requirements.
A.5.1.4. The determination of the VSL is obtained by the classification rules stated on item A.5.2.
A.5.1.5. All VDS presented herein are formulated according its specific VSL indication. Design premises, such as
materials (metallic / non-metallic), configurations, tests and design validation are based on the criticality foreseen in the
application/use of the valve and defined by the specific VSL.
A.5.1.6. For any given VSL, there is a set of requirements associated with it (item A.5.3).
A.5.1.7. The manufacturer of the valve shall attend all requirements listed in the VDS, including the specific requirements
of VSL.
A.5.1.8. It is possible to have more than one type of valve (e.g.: ball, gate, etc.) with the same VSL number, and possibly
both types would be able to attend a certain application. In this case, it shall be conducted by the Project and/or user an
evaluation of the valve features associated with the foreseen application, and so define the type of valve that shall be
specified in the Project and/or specific application.
A.5.1.9. The valve’s feature are presented in item A.5.4, and allows an adequate understanding about which type of
valve is more suitable for the intended application.
A.5.2.1. The VSL classification shall be taken according premises indicated in this item. It shall be evaluated the following
parameters by the Project and/or user:
Application: it shall be verified the application of the valve. Safety valves (e.g.: HIPPS, SDVs, etc.) have a
deterministic VSL, not depending on complementary analyses such as stablished for other type of valves.
Service: it shall be verified the service conditions where the valve will be installed. Services such as hydrocarbon,
hot water, toxic or inflammable shall classify a higher grade of VSL.
c) Accumulated energy: it shall be verified the classification of accumulated energy associated with the use of the
valve, as described in Table A.1.
d) Demand: the expected number of cycles during the lifetime of the valve shall be taken into account when
considering the VSL. The higher the number, the higher the VSL, as described in Table A.1.
- Rev. 11 - Page 11 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
High Demand Actuated Filter valves, Actuated XVs, Actuated molecular sieve valve
Application Level
High Demand
Service (Note 2) Accumulated Energy
Yes No
Hydrocarbon
Hot water High
Inflammable VSL-3 VSL-2
Steam Low
Toxic
High VSL-2
Other valves Other services VSL-2
Low VSL-1
Note 1 – This table is not applicable for valves in tubing specifications.
Note 2 – See below the fluids belonging to each service:
- Hydrocarbon/Inflammable/Toxic: AM, CI, CI2, CN, CNI, D, DF, DFC, DOH, F, FG, G, GL,
H, IGN, JF, OL, P, PC, PCG, PLD, TR;
- Hot water: HWP;
- Steam: S;
- Other services: ADW, AO, BG, BR, BWG, BWH, CHW, CV, DA, DO, DTH, DW, EG, FL,
FLC, FP, FW, GW, HF, HWP, HWU, IA, IG, IN, IW, IWC, PCW, PW, PWH, SA, SC, SFW,
SN, SP, STA, SW, TC, TL, W, WW.
A.5.3.1. Each VSL classification inputs to the valve design a basic information about which API 6D - Quality Specification
Level (QSL) shall be fulfilled, plus a sort of specific requirements (mandatory).
A.5.3.2. The QSL classification and requirements are according API 6D: QSL-1, QSL-2, QSL-3 or QSL-4. All
requirements listed in API 6D Annex J shall be attended according the respective QSL related to the VSL.
A.5.3.3. The QSL refers to specific requirements for NDT, pressure testing and documentation of the valve.
A.5.3.4. The VSL requirements shall be as described in Table A.3:
- Rev. 11 - Page 12 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
QSL QSL-3
QSL-2 QSL-3 QSL-4
(According API 6D) (Note 1)
Fugitive Emissions
Design No Yes / No (Note 2) Yes / No (Note 2) Yes / No (Note 2)
(According item A.6.1.6)
Fire Resistant No
Yes / No (Note 4) Yes / No (Note 5) Yes
(According item A.6.1.4) (Note 3)
Design Validation
No Design analytical approval Design validation test approval (PVT)
(According item A.9.2)
SIL Capable
No No No Yes / No (Note 6)
(According item A.6.1.7)
Note 1 – For liquid service application, it may be considered QSL-2, except for hydrocarbon.
Note 2 – The valve design shall be fugitive emissions approved if the valve will be specified for use in a process pipe that fluid
contains volatile organic compounds (e.g.: benzene), and its emissions to environment are limited by a regulamentory law.
Note 3 – If fire resistant requirement is requested by the Project, it shall be considered the use of a VSL-2 valve.
Note 4 – Indication of fire resistant valve shall be taken according design premises.
Note 5 – SDV, BDV and XV valves shall be fire tested. For other valves, indication of fire-tested valve shall be taken according
design premises.
Note 6 – SIL capable applies only for HIPPS valve.
A.5.4.1. For each type of valve, Table A.4 presents a summary of valve features and typical applications.
- Rev. 11 - Page 13 of 79
Ball Gate Check Globe Butterfly
Features R is ing Axial Plug Needle Diaphragm
M etal A xia l
Stem S o lid C ha m f e r C a t e go ry A C a t e go ry B C a t e go ry B
So ft to E xpa nding S la b P is t o n D ua l P la t e S wing ( N o n-
(M etal to We dge D is c ( c o nc e nt ric ) ( bi- e c c e nt ric ) ( t ri- e c c e nt ric )
M etal s la m )
M e t a l)
Actuated design
A A A A A A N/A N/A N/A N/A A A A A A A N/A A
(e.g.: hydraulic, electric, pneum atic)
Metal to Metal seat design No Yes Yes Yes A Yes Yes A Yes A Yes No No Yes Yes No Yes No
Fire tested design A A Yes N/A A N/A N/A N/A N/A N/A N/A No A A A A N/A No
- Rev. 11 -
Fire safe design N/A N/A N/A A N/A A A A A A A No N/A N/A N/A N/A A No
Fugitive em issions design A A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A
Fit to control application N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A P N/A N/A N/A N/A N/A P N/A
SIL capable design N/A A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A A N/A N/A N/A
Table A.4 - Valve features and typical applications
Fit to SDV Platform Lim its N/R A N/R N/R N/R A N/R N/R N/R N/R N/R N/R N/R N/R N/R N/R N/R N/R
N/R A N/R N/R N/R A N/R N/R N/R N/R N/R N/R N/R A N/R N/R N/R N/R
(Hydrocarbon service)
Fit to SDV, BDV application
A A N/R N/R N/R A N/R N/R N/R N/R N/R N/R N/R A N/R N/R N/R N/R
(Non-hydrocarbon service)
Fit to L/R PIG application N/R A N/R N/R N/R N/R N/R N/R N/R N/R N/R N/R N/R N/R N/R N/R N/R N/R
Fit to m olecular sieve application N/R N/R P N/R N/R N/R N/R N/R N/R N/R N/R N/R N/R ALT N/R N/R N/R N/R
Fit to ADV application N/R N/R N/R N/R N/R N/R N/R N/R N/R N/R N/R N/R A N/R N/R N/R N/R A
Legend: A – Available; ALT – Alternative solution; P – Preferential solution; N/R – Not Recommended; N/A - Not Available
Page 14 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
A.6.1.1.1. Regarding documentation hierarchy, valve design shall be according the Standard referenced in the VDS. In
case of conflict between the requirements herein stablished and that Standard, the attendance of this document shall
be considered as mandatory.
A.6.1.1.2. The valve design shall attend all quality, functional, materials, testing, and configuration requirements
specified in the VDS.
A.6.1.1.3. The assembly of the valve / actuator shall meet all operating conditions, in any position of installation, without
performance reduction. Unless clearly specified, it shall be able to operate under full rated condition, such as opening
and closing at full differential pressure, according to the design pressure indicated in the VDS.
A.6.1.1.4. For a heavy weighted valve (Weight > 25 kg) or a valve with larger dimensions (L+W+H > 1500 mm), the
corresponding design shall consider the use at least of four (4) lifting handles. The vertical line of the lifting points shall
be left free to avoid interference with the drive system or actuator.
A.6.1.1.5. The manufacturer shall present all dimensional drawings of the valve and actuator, with a list of all parts and
materials specifications.
A.6.1.1.6. The manufacturer shall present a list of required torques on the valve shaft, containing the following values of
torque: Nominal Torque of Operation (TNO), Maximum Torque of Operation (TMO) and Maximum Allowable Torque
(TMA), taking into account the pressure class of the valve and temperature limits.
Note: for gate and globe valves with manual actuation, TNO shall be according MSS SP-91; for ball valves, the TNO
shall comply with API 6D; and for butterfly valves, the TNO shall be according API 609.
A.6.1.1.7. The manufacturer shall inform in the documentation all design and/or operation constraints (e.g.: installation
position, flow direction, flow rate, limits of pressure, temperature and metallic / non-metallic materials, etc.).
A.6.1.1.8. Valve ID (bore) shall be compatible with the ID of the pipes and accessories in which the valve is installed.
A.6.1.1.9. All metallic materials shall have a mill certification, with registers of chemical composition, mechanical
properties and other standards requirements, besides the manufacturer batch identification.
A.6.1.1.10. For valve designs which allows retained pressure in body cavity (when valve is fully closed or fully open),
plugs capable to mitigate risk of an accident under an eventual remotion shall be used. In this case, those ports shall be
closed with plugs having a constructive configuration that allows pressure relieving to atmosphere (relief hole) during
the beginning of plug remotion, serving as an alert to the operator about the remaining pressure inside the valve body.
An example of this kind of configuration is showed as follows:
- Rev. 11 - Page 15 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
A.6.1.2.1. The design of the valves shall attend one of the following classification of material classes:
# Material Class
C Carbon Steel
A Alloy Steel
S Stainless Steel
D Duplex Steel
N Nickel Alloy
U Uncommon materials
A.6.1.3.1. The referred letter of the material class of the valve, shown on the first column of Table A.5, associated with
the number indicated in the lines of Table A.6, gives the body material considered in the valve design. The combination
of the letter and number shall be considered as a part of the valve code, according description of valve code presented
on item A.11.5.
Material Class
Body C A S D N U
Material Stainless Uncommon
Carbon steel Alloy steel Duplex steel Nickel alloys
steel materials
ASTM A182
ASTM A105 ASTM A350 LF3 Gr. F304
Inconel 625
1 or or or ASTM A995 Gr. 1B
(UNS N06625)
Bronze
ASTM A216 WCB ASTM 352 LC3 ASTM A351
Gr. CF8
ASTM A182
ASTM A182 Gr.
A350 LF2 CL1 Gr. F316
F51
2 or ASTM A182 F5 or
or
- ASTM A536-65-45-12
ASTM A352 LCB ASTM A351
ASTM A995 Gr. 4A
Gr. CF8M
ASTM A105
or ASTM A182
Gr. F317 ASTM A182 Gr.
ASTM A216 WCB ASTM A182 F11 ASTM B148
3 + CL2
or F55 or -
(UNS C95800)
ASTM A351 ASTM A995 Gr 6A
Organic Coating Gr. CG8M
(Onshore use only)
ASTM A105
or ASTM A182
Gr. F347
ASTM A216 WCB
4 +
ASTM A522 Type I or - - Plastics
ASTM A351
Organic Coating Gr. CF8C
(Offshore)
- Rev. 11 - Page 16 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
Material Class
Body C A S D N U
Material Stainless Uncommon
Carbon steel Alloy steel Duplex steel Nickel alloys
steel materials
ASTM A105 ASTM A350 LF3
or or
ASTM A216 WCB ASTM A352 LC3
5 + + - - - Gray Iron
Full Clad Inconel Full Clad Inconel
625 overlay 625 overlay
(UNS N06625) (UNS N06625)
ASTM A350 LF2
CL1
ASTM A522 Type I
or
+
ASTM A352 LCB
6 +
Full Clad Inconel - - - -
625 overlay
Full Clad Inconel
(UNS N06625)
625 overlay
(UNS N06625)
A.6.1.3.2. The use of forgings or castings for the body material shall follow the following classification according the VSL
of the valve, and indicated in the VDS:
Pressure Class
VSL
150 300 600 900 1500 2500 10000
VSL-1
Forging or Casting Forging (Note 1)
VSL-2
VSL-3
Forging (Note 1)
VSL-4
Note 1 - Except for axial block valves (VAX), for which casting is acceptable.
A.6.1.4.1. In order to obtain indication that the valve design shall be fire tested type, it shall be fulfilled all requirements
listed in DR-ENGP-I-1.3, such as the execution of the “Risk Assessment and Safety Studies” (item 5 of DR-ENGP-I-1.3)
and the “Consequence Analysis - (fire propagation, gas dispersion, explosion, etc.)”.
A.6.1.4.2. Whenever specified in the VDS that the valve shall be fire tested, its design shall be submitted to a certification
by testing a prototype according to ISO 10497, API 6FA or API 607 (except 4th edition).
A.6.1.4.3. The manufacturer shall present to PETROBRAS the correspondent certificate and the valve shall be marked
as described on item A.6.1.10.
A.6.1.4.4. The design of the seals on seats/body and stem areas shall consider mandatory the use of a metallic element
or an element made by graphite, to guarantee the attendance of the fire testing requirement. This element shall be
installed on each leakage path of the valve.
A.6.1.5.1. In order to obtain indication that a valve design shall be fire safe type, it shall be fulfilled all requirements listed
in DR-ENGP-I-1.3, such as the execution of the “Risk Assessment and Safety Studies” (item 5 of DR-ENGP-I-1.3) and
the “Consequence Analysis - (fire propagation, gas dispersion, explosion, etc.)”.
- Rev. 11 - Page 17 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
A.6.1.5.2. Whenever specified in the VDS that the valve shall be fire safe, its design shall contain material specification
applying materials that are capable of withstanding exposure to fire without failure.
A.6.1.5.3. The fire safe design does not require valve certification, but it shall guarantee that the valve design is resistant
to a fire scenarium.
A.6.1.5.4. The design of the seals on seats/body and stem areas shall consider mandatory the use only of a metallic
element or an element made by graphite, to guarantee the attendance of the fire safe requirement.
A.6.1.6.1. In order to prevent a failure on a valve (e.g.: leaking toxic fluid to external environment), that could contribute
to the minimize safety to personnel, installation and/or environment, some valves shall be designed to be fugitive
emissions approved.
A.6.1.6.2. Whenever specified in the VDS that the valve shall be fugitive emission approved, its design shall be certified
according ISO 15848 Part 1, by prototype approval to confirm that an adequate design of seals (on body joints and stem)
is provided.
A.6.1.6.3. The manufacturer shall prepare specific Performance Verification Test (PVT) procedure, according ISO 15848
Part 1, and submit for PETROBRAS approval.
A.6.1.6.4. The manufacturer shall provide the certificate of approval containing information about the design
“Performance Class” according ISO 15848 Part 1. Information about “Tightness Class”, “Endurance Class”, and
“Temperature Class” shall be presented in details.
A.6.1.6.5. The “Tightness Class” shall be according:
Table A.8 – Tightness class for stem seals - fugitive emissions (ref.: ISO 15848 Part 1)
Table A.9 – Tightness class for body seals - fugitive emissions (ref.: ISO 15848 Part 1)
Measured leakage
≤ 50 1
(Body seals)
1
Expressed in ppmv measured with the sniffing method as defined in
ISO 15848 Part 1 - Annex B
- Rev. 11 - Page 18 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
Table A.10 – Tightness class for stem (or shaft) seals with methane - fugitive emissions (ref.: ISO 15848 Part 1)
AM ≤ 50
BM ≤ 100
CM ≤ 500
1
Expressed in ppmv measured with the sniffing method as defined in ISO 15848 Part 1 - Annex B
Table A.11 – Leakage from body seals with methane - fugitive emissions (ref.: ISO 15848 Part 1)
≤ 50
A.6.1.6.6. The Mechanical-cycles shall be performed according ISO 15848 Part 1, considering the following “Endurance
Class” x VSL:
Table A.13 – Temperature class of fugitive emissions (ref.: ISO 15848 Part 1)
A.6.1.7.1. The concept of Safety Integrity Level (SIL) shall be applied for valves dedicates to a HIPPS system.
A.6.1.7.2. The SIL is a representation of the required safety unavailability (average probability of failure on demand -
PFD) of a safety instrumented function (SIF).
A.6.1.7.3. The SIL classification shall be as listed in Table A.14, where SIL 4 has the highest level of safety integrity,
and SIL 1 has the lowest.
- Rev. 11 - Page 19 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
A.6.1.7.4. Whenever requested in the VDS, such as for HIPPS valve, the SIL to be considered in the design of the valve
shall be SIL-3. The manufacturer shall present all documentation in order to certify that SIL 3 requirements were
achieved for the valve design.
A.6.1.8. BOLTING
A.6.1.8.1. The Studs, bolts and nuts used in the body-closure and body-bonnet shall be according:
ASTM A105
ASTM A193 Gr. B7 ASTM A194 Gr. 2H
ASTM A216 Gr. WCB According
item
ASTM A350 Gr. LF2 CL1 A.6.1.8.2
ASTM A320 Gr. L7 ASTM A194 Gr. 4L or 7L
ASTM A352 Gr. LCB
A.6.1.8.2. The studs, bolts and nuts shall be coated with zinc-nickel (Zn-Ni) according ASTM B841, Class 1, Type B / E,
Grade 5-8, with post-coating hydrogen embrittlement relief, according ASTM B 849 and ASTM B 850;
A.6.1.8.3. For studs and bolts according ASTM A320 Gr L7, and the valve body material is ASTM A350 Gr LF2 CL 1 or
ASTM A352 Gr LCB, it will be acceptable charpy impact testing at -45°C. If the valve body material is ASTM A350 Gr
LF3 or ASTM A352 Gr LC3, it will be acceptable charpy impact testing at -60°C;
A.6.1.8.4. The studs used in the body-closure (ball, check and plug) and body-bonnet (gate and globe) shall be according
ASME B1.1, UNC-2A up to 25,40mm (1") and 8UN-2A, from 28,57mm (1 1/8") up, with standard hex nuts according
ASME B18.2.2, with a minimum of four. The length of the studs shall have minimum of one and maximum of three screw
threads beyond the nut. For valves with DN 40 (1 1/2”) and smaller, is allowed the use of bolts according ASME B18.2.1.
Alternatively, studs, bolts and nuts may be according metric units;
A.6.1.8.5. Valves subjected to fire type-testing shall be assembled with studs, bolts and nuts according Table A.15. For
- Rev. 11 - Page 20 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
the cases not covered in Table A.15, the manufacturer shall properly specify bolting materials. In this case, this set shall
be used for fire type-testing. As an alternative of ASTM A193 Gr B7, studs made of ASTM A193 Gr B16 may be used,
considering coating requirements indicated in item A.6.1.8.2.
A.6.1.8.6. Studs, bolts and nuts made of austenitic stainless steel (e.g.: Type 316) shall not be used when exposed to
wet marine atmosphere with maximum operating temperature above 60°C if. As an alternative, ASTM A193 Gr. B7 may
be used.
A.6.1.9. PAINTING
A.6.1.9.1. If painting of the valve is contractual required, the manufacturer shall present for PETROBRAS approval the
Painting Inspection Plan, according PETROBRAS’s specification and approved by a Painting Inspector Level II;
A.6.1.9.2. It shall be documented all painting inspection registers, and submitted for PETROBRAS;
A.6.1.9.3. The color to be applied on the valves shall according DR-ENGP-M-I-1.15.
A.6.1.9.4. Coating systems specified for offshore and coastal applications shall be selected in accordance with ISO
12944-9 corrosion category CX high durability and I-ET 3010.00-1200-956-P4X-002.
A.6.1.10.1. All valves shall be marked in accordance with the requirements stated on the design Standard referenced in
the VDS.
A.6.1.10.2. Each valve shall be provided with an austenitic stainless steel nameplate securely affixed and so located
that it is easily accessible.
A.6.1.10.3. The nameplate shall present information in accordance with the requirements stated on the design Standard
referenced in the respectively VDS, plus the additional data:
Indication about the VSL of the valve, such as: VSL-1, VSL-2, VSL3 or VSL-4.
Indication about fire tested design (when applicable).
Indication about fugitive emissions design (when applicable).
A.6.1.10.4. For trunnion mounted ball valves, despite of the separate identification plate requested by API 6D to indicate
the direction of seats valves with one unidirectional seat and one bidirectional seat, each valve shall present a separate
identification plate indicating the seat configuration, such as ilustraded in Figure A.2.
A.6.1.10.5. Valves designed with unidirectional flow capability, i.e. flow occurs only in one direction, shall be marked with
a flow direction arrow or with a separate identification plate fixed to the body, indicating the direction for which flow is
permitted.
- Rev. 11 - Page 21 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
A.6.2. ACTUATOR
A.6.2.1. GENERAL
A.6.2.1.1. In general, all VDS contain technical specification considering manual actuated valves. The actuation for
manual valves may be as a wrench, hand wheel or gearbox operator.
A.6.2.1.2. Other types of actuators, such as hydraulic, pneumatic or electric, may be considered by PETROBRAS to be
used. In this case, the manufacturer shall design the valve and actuator considering also the specific datasheet.
A.6.2.1.3. When applicable (i.e.: control valve, SDV and BDV), the design of actuators shall consider the requirements
stated in DR-ENGP-M-I-1.5.
A.6.2.1.4. When applicable, the actuator shall be equipped with a positioning indicator, in order to show correct and
clearly the position of the valve (open or close). The position of a wrench or indicator shall be in the direction of the
line/bore when the valve is open and be perpendicular to the line/bore when the valve is closed.
A.6.2.1.5. For gearbox operator, the connection between the valve body and the gearbox shall be vented so that any
leakage from the stem cannot penetrate into the gearbox housing.
A.6.2.1.6. In case hydraulic actuator is considered, the manufacturer shall design it in order to have a maximum
operating pressure (e.g.: opening under full differential pressure) of 90% of the nominal operating pressure.
A.6.2.1.7. The actuator shall be designed with a safety factor of 2 times the nominal torque during normal operation
condition (maximum available torque = 2 x nominal torque).
A.6.2.1.8. For hand wheel actuated valves, the hand wheel shall be designed to allow operation of the valve under full
differential pressure. It shall also attend the requirements listed in MSS SP-91.
A.6.2.1.9. Levers and handwheels shall be in grade 316 stainless steel material.
Use of Gearbox
Pressure
Type x
Class
DN(NPS) ≥
150 300 (12)
- Rev. 11 - Page 22 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
Use of Gearbox
Pressure
Type x
Class
DN(NPS) ≥
1500, 2500 50 (2)
Butterfly Category A
CWP and 150 250 (1O)
(concentric)
A.7.1.1.1. The valve shall be designed to operate and seal, according design premises, under the following conditions:
a) high pressure, equivalent to MWP, being able to operate and seal with high and low differential pressure.
b) low pressure, equivalent to LP of specific QSL requirement, being able to operate and seal with a low differential
pressure.
A.7.1.1.2. The type of the seats, regarding SPE or DPE, shall be used in the assembly of the valve in order to guarantee
the isolation valve configuration specified in the VDS (i.e.: DBB, DIB-1 or DIB-2). Any deviation shall be submitted for
PETROBRAS approval.
A.7.1.1.3. All sealings specified for the body construction shall be bi-directional, and no visible leakage shall be
considered to external environment.
A.7.1.1.4. The sealing type of the valve, regarding Metal to Metal or Soft sealing, shall be according the indication in the
VDS. Any deviation shall be submitted for PETROBRAS approval.
A.7.1.1.5. A Metal to Metal seated ball valve consists exclusively in use of a metal to metal sealing between seats and
ball, without the use of a non-metallic insert;
A.7.1.1.6. A soft seated ball valve consists in use of a non-metallic insert to guarantee its sealing performance. In this
case, the seat insert design and its groove shall be designed in order to prevent extrusion under all operation conditions.
A.7.1.1.7. Whenever specified in the VDS, the manufacturer shall attend to the metallic coating specified for the sealing
surfaces, such as in the body, bonnet, ball, seats, etc. In this case, the manufacturer shall attend the applicable
requirements listed on items A.7.1.7.3 and A.8.
A.7.1.1.8. Whenever specified in the VDS, the manufacturer shall attend to the hard coating specified for the sealing
surfaces, such as in the ball and seats. In this case, the manufacturer shall attend the applicable requirements listed on
items A.7.1.7.4 and A.8.2.2.
A.7.1.1.9. Whenever specified in the VDS, the manufacturer shall attend to the organic coating specified. In this case,
the manufacturer shall attend the applicable requirements listed on item A.8.2.2.4.
A.7.1.1.10. Valves with NPS 3 (DN 80) and smaller may have a single drain and vent connection, at the lowest possible
- Rev. 11 - Page 23 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
position on the valve body cavity.Valves NPS 4 and higher shall contain both drain and vent ports, in order to allow drain,
purge, pressurization and monitoring through the body during testing. MSS SP45 shall be considered, with the additional
requirements:
a) For trunnion ball valves, the body shall contain a threaded hole with drain plug in position "G" or "J", according
Figure A.3. It is not allowed to mount plugs using PTFE tape.
A.7.1.1.11. For trunnion ball valves type DIB-1, or when requested in the VDS, it shall be provided with an automatic
cavity-pressure relief. In this case, it shall be considered the use of a block valve before the cavity-relief valve.
A.7.1.1.12. For floating ball valves (NPS ≥ 2) and for trunnion ball valves, it shall be designed in order to allow pressure
relief in the cavity from exceeding 1,33 times the valve pressure rating at the specified maximum operating temperature.
A.7.1.1.13. The ball shall be full bore type, cylindrical and solid as shown in Figure A.4.
A.7.1.2.1. The following standards shall apply to the design of ball valves:
- Rev. 11 - Page 24 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
ASME
Standard API 6D / IOGP S-562 d ISO 17292 API 6D
B 16.34 LTD
b For DN > standard diameter, face to face shall be by agreement between manufacturer and PETROBRAS. The design shall be
A.7.1.3.1. The design of metallic ball valves (Metal to Metal or Soft seated) shall attend the following characteristic
regarding mounting:
A SPE/SR assembly seat provides sealing only when differential pressure is higher from outside of the
valve. When the SPE assembly seat faces higher differential pressure from inside of the valve (cavity), it occurs self-
relieving.
A SPE/SR assembly seat may be provided on a metal to metal seat design or on a soft seated design.
- Rev. 11 - Page 25 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
Left side of Figure A.5 illustrates the sealing mechanism when pressure (or higher differential pressure) is
applied from outside of the valve. The difference in the area (“D”) times the line pressure creates a piston effect force
which pushes the seat against the ball surface resulting in a sealing between ball and seat.
Right side of Figure A.5 illustrates the relief mechanism when a higher differential pressure is applied from
the cavity of the valve. When the pressure in the valve cavity reach certain pressure (so that the total force from cavity
pressure that act on the seat is higher than the force causing by the upstream pressure), the trapped pressure will have
enough force to push the seat and relief the valve cavity pressure.
Figure A.5 – SPE/SR seat assembly mechanism (illustration on a soft ball valve)
A DPE assembly seat provides sealing on both directions, when differential pressure is higher from
outside/inside of the valve.
A DPE assembly seat may be provided on a metal to metal seat design or on a soft seated design.
Left side of Figure A.6 illustrates the sealing mechanism when pressure (or higher differential pressure) is
applied from outside of the valve. The difference in the area (“D”) times the line pressure creates a piston effect force
which pushes the seat against the ball surface resulting in a sealing between ball and seat.
Right side of Figure A.6 illustrates the sealing mechanism when pressure (or differential pressure) is applied
from the cavity of the valve. The difference in the area (“D”) times the cavity pressure creates a piston effect force which
pushes the seat against the ball surface resulting in a sealing between ball and seat.
Figure A.6 – DPE seat assembly mechanism (illustration on a soft ball valve)
A.7.1.4.3. Whenever not specified in the VDS, the valve design shall consider as a standard isolation valve configuration
the use of two unidirectional sealing seats, giving a characteristic of single piston effect (SPE) or self-relief (SR) on both
seats.
A.7.1.4.4. In order to ensure adequate operational requirements, whenever specified in the VDS, the design of trunnion
- Rev. 11 - Page 26 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
ball valves (Metal to Metal or Soft seated) may attend one or more of the following functions/features:
The DBB feature of the valve is the ability to segregate two pressure sources and to bleed/vent pressure in the valve
body between the two seats when the valve has the DBB feature. The DBB feature may be obtained by using SPE/SR
or DPE seats.
Figure A.7 – DBB feature (ref.: Double Block and Bleed - Type B of API 6D)
The DIB-1 feature of the valve is the ability to provide two sealing elements to a single pressure source, and to bleed/vent
between the two sealing elements. It shall be considered Upstream and Downstream as bidirectional sealing seat (DPE
seats).
Figure A.8 – DIB-1 feature (ref.: Double Isolation and Bleed - Type B of API 6D)
Valves designed with a DIB-1 feature shall be provided with automatic cavity-pressure relief, unless otherwise agreed.
In this case, it shall be attended all requirements described on API 6D (ref. item 5.8 of API6D).
The DIB-2 feature of the valve is the ability to provide two sealing elements to a single pressure source, and to bleed/vent
between the two sealing elements. It shall be considered the Upstream as unidirectional sealing seat (SPE seat) and
downstream as bidirectional sealing seat (DPE seat).
Figure A.9 – DIB-2 feature (ref.: Double Isolation and Bleed - Type B of API 6D)
- Rev. 11 - Page 27 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
All DIB-2 valves shall have a clear identification about seat sealing direction, by marking on a separate identification
plate affixed to valve body both seats type of sealing (SPE or DPE).
The assembly of a DIB-2 valve on the line shall attend its preferred direction.
A.7.1.4.5. Depending on detailed design, indicated in the VDS, the valve may have an isolation valve configuration as
follows:
Isolation valve Single Piston Double Block and Bleed Double Isolation and Bleed
Effect (SPE) on
configuration both seats (DBB) Feature (DIB-2) Feature
1 Yes No No
2 Yes Yes No
1
3 No Yes Yes
4 No Yes 2 Yes
1
DBB feature applied in the closed position (only).
2
DBB feature applied in the opened and closed position (both).
Note: The use of DIB-1 feature has not been foreseen. Particular analyses of use may be conducted by Project
team and/or an Operational Unit (UO).
A.7.1.5.1. All non-metallic seals shall be suitable for the pressure, temperature and service conditions considered in this
item.
A.7.1.5.2. The manufacturer of the valve shall guarantee together with your seals supplier(s) the attendance of the
essential material requirements for the non-metallic seals, in order to ensure that the designed seal system works
properly during the whole design life of the valve.
A.7.1.5.3. The VDS of soft seated ball valves indicates the material of the seat insert.
A.7.1.5.4. The use of certain seat insert material shall be based on the following classification:
Note: The values listed in Table A.20 presents the limits of temperature that shall be applied in the valve design
considering operational conditions of it.
A.7.1.5.5. For the design of the seats / stem seals, in Metal to Metal or Soft seated ball valves, the VDS contains
- Rev. 11 - Page 28 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
indication about the non-metallic group material that shall be considered in the valve design.
A.7.1.5.6. The materials of each group are indicated in Table A.21, according the following classification:
- Group A – Terpolymer of VF2, HFP e TFE with fluor content of ~ 67 - 70% or HNBR with %ACN between 36
and 40%. E.g.: Viton B (DuPont), Technoflon TN (Solvay Solexis);
- Group B – Ter- or Tetrapolymer of TFE, VF2 and PMVE with fluor content of ~ 62-68% or HNBR LT (%ACN
between 36 and 40%) both with TR10 ≤ -30°C according ASTM D1329. E.g.: Viton GLT (DuPont), Technoflon
855 (Solvay Solexis);
- Group C – Terpolymer of PP, TFE and VDF with higher resistance to bases or perfluoro elastomer (FFKM). e.g.:
FKM Type 4- Aflas (Asashi Glass), BRE 7132 (Dyneon), FFKM- Kalrez, Chemraz, Technoflon PFR (Solvay
Solexis);
- Group D – Terpolymer of PP, TFE and VDF with higher resistance to aromatic hydrocarbons or perfluoro
elastomer (FFKM). e.g.: BRE 7132 (Dyneon), FFKM- Kalrez, Chemraz, Technoflon PFR (Solvay Solexis);
- Group E – Polytetrafluoroethylene (PTFE) based Chevron Packing or Polytetrafluoroethylene (PTFE) energized
with a Co-Cr-Ni alloy UNS R30003 (Elgiloy) spring;
- Group F – Graphite 98% pure, Graphoil or a metallic seal.
Design Transient
Seals Temp. 1 Temp. 2 Seals Seals Group
Application RGD Suitable for
Group Min. Max. Min. Max. Materials Design Restrictions
(° C ) (° C ) (° C ) (° C )
O-ring Water, Utility, Amines
HNBR Steam
Normal Polypak Sweet
Group A 0 +150 0 +170 No Aromatic
Temperature FKM Type 2 hydrocarbon
Gasket and Chemicals hydrocarbons 4
O-ring
HNBR LT Sweet Amines, Steam,
Low Polypak
Group B
Temperature
- 30 +150 - 46 +170
FKM Type 3 Yes 3 hydrocarbon Aromatic
Gasket (Gas) hydrocarbons 4
O-ring
Medium High FKM Type 5
Group D Temperature + 0 +210 0 +240 Polypak No All -
Aromatics FFKM
Gasket
PTFE based
Wide Range Chevron Seal6
Group E 5
- 100 +200 - 100 +240 PTFE based + N/A All -
Service UNS R30003 Lip Seal
(Elgiloy)
Graphite 98% Pure
Gasket
High Graphoil
Group F - 100 +500 - 100 +500 N/A All -
Temperature C-Ring
Metallic Seal
1 Temperature range for use of non-metallic material (i.e.: seats / stem seals) in the valve design. It shall be considered for
continuous service without reducing the seals' economic life or its sealing capability.
- Rev. 11 - Page 29 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
2 Temperature range considered whether the seals may be exposed for a short period of time (transient temperature spike),
under a static condition (without operation), with a possible leakage but without permanently damaging the sealing system.
3 RGD according ISO 23936-2 for valves of pressure class 300 or above.
4 Hydrocarbons streams containing more than 25% aromatics.
5 The use of Group E is acceptable in replacement of Groups A, B, C or D, as long as the design of the valve considers application
of Inconel 625 overlay (partial clad) on all sealing areas.
6 Use of Chevron packing shall be combined with anti-extrusion PEEK rings.
A.7.1.5.7. As a reference, the use of each group seal are based to the following fluid classes & temperature ranges:
Table A.22 – Indication of groups of seals according fluid class and temperature range
Temperature Range
Fluid Class Normal Low Medium High Wide Range High
(0 ° C to +1 5 0 ° C ) ( - 3 0 ° C to +1 5 0 ° C ) (0 ° C to +2 1 0 ° C ) ( - 1 0 0 ° C to +2 0 0 ° C ) ( - 1 0 0 ° C to +5 0 0 ° C )
Utility Group A - - - -
Water Group A - - - -
A.7.1.5.8. For the indication of a valve configuration, it shall be considered the following classification as a part of the
valve code, according description of valve code presented on item A.11.5:
- Rev. 11 - Page 30 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
Fugitive Emissions 4 9
A.7.1.6.1. This item presents typical configurations for ball valves, as a result of combinations of materials and features.
The configurations herein listed are considered to create a specific VDS.
A.7.1.6.2. The referred number of the typical configuration of the valve, shown on the first column of Table A.25 and
Table A.26, shall be considered as a part of the valve code, according item A.11.5.
The design of ball valves up to NPS 1 1/2 (“Forged” valves) shall consider the use of a nipple with extension
of 100,00 millimeters.
For the indication of the nipple considered in the valve configuration, it shall be considered the following
classification as a part of the valve code, according description of valve code presented on item A.11.5.
Pressure Class
SCH
800 1 1500 2500
40S 801 1501 2501
80 802 1502 2502
160 803 1503 2503
XXS 804 1504 2504
1 Code 800 is used for screwed ended connections.
The following basic configurations shall be considered in the design of ball valves up to NPS 1 1/2 (“Forged”
valves):
Table A.25 – Typical configurations for ball valves up to NPS 1 1/2 (“Forged” Valves)
Config. Sealing Pressure Seat Insert Stem Seal Fire End Seats
DBB VSL
# Type Class Material Material Tested Connection Configuration
- Rev. 11 - Page 31 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
Config. Sealing Pressure Seat Insert Stem Seal Fire End Seats
DBB VSL
# Type Class Material Material Tested Connection Configuration
04 PEEK Group C, E
Metal
05 to N/A Group D, E
Metal
The following basic configurations shall be considered in the design of ball valves NPS 2 and above:
Table A.26 – Typical configurations for ball valves NPS 2 and above
- Rev. 11 - Page 32 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
The following basic configuration shall be considered in the design of rising stem ball valves:
05 Flanged
Group E
06 Flanged x NPT
Metal
150, 300, 600
to N/A
900, 1500, 2500
Metal
07 Flanged
Group F
08 Flanged x NPT
Table A.29 presents the standardized materials for each combination of material and pressure class of the
valve. The stem materials listed herein are considered to create a specific VDS.
Alternative materials are presented when applicable. The use of it shall be approved by PETROBRAS.
Table A.29 - Stem materials according material class & pressure class of the valve
- Rev. 11 - Page 33 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
Table A.29 - Stem materials according material class & pressure class of the valve
Pressure Class
Material Class Alternate Material
150 300 600 800 900 1500 2500
ASTM A564 Type
630 (UNS S17400)
ASTM A276
ASTM A276 (UNS S31803)
Carbon Steel
(UNS S41000) ASTM A276
(UNS S32760)
ASTM B637
(UNS N07718)
ASTM A276
Carbon Steel
(UNS S31803)
with Organic
ASTM A276 ASTM A276
Coating
(UNS S31803) (UNS S32760)
(Onshore / ASTM B637
Offshore) (UNS N07718)
Carbon Steel
with Inconel 625 ASTM B637
N/A
overlay (UNS N07718)
(UNS N06625)
ASTM A564 Type
ASTM A564 630 H1150 (UNS
Stainless Steel ASTM A276 (UNS S31600) Type 630 H1150 S17400)
(UNS S17400) 1 ASTM B637
(UNS N07718)
ASTM A276
(UNS S32760)
ASTM A276 ASTM B637
Duplex Steel
(UNS S31803) (UNS N07718)
Hastelloy C276
(UNS N10276)
ASTM B637
Super Duplex ASTM A276 (UNS N07718)
Steel (UNS S32760) Hastelloy C276
(UNS N10276)
Alloy Steel
ASTM B637
(ASTM A333 N/A
(UNS N07718)
Gr.3)
Alloy Steel
ASTM B637
(ASTM A333 N/A
(UNS N07718)
Gr.8)
1
Whenever Group E is considered as seats / stem seals material in metal to metal ball valves (due to low temperature
requirements), it shall be used ASTM B637 (UNS N07718).
- Rev. 11 - Page 34 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
All valves design shall consider the use of Inconel X750 (UNS N07750) as spring material, to be used on
the seat assembly.
Whenever specified in the VDS use of partial clad, it shall be considered the application according:
Table A.30 – Specification of metallic coating (partial clad) for ball valves
Partial Clad
Stainless Steel
(AISI 316) Valves with VSL = 2 which Material Class is Carbon Steel or Low Temperature Carbon Steel
Weld Overlay
Nickel Alloy Valves with VSL ≥ 3 and all valves with seals (seats/stem) using Group E.
(Inconel 625) Note: Only applicable for valves with Material Classes Carbon Steel, Low Temperature Carbon Steel or
Weld Overlay Stainless Steel
Whenever specified in the VDS partial clad, it shall be considered the application of CRA (according Table
A.30) on all body sealing areas.
Whenever specified in the VDS full clad, it shall be considered the application of Nickel Alloy (Inconel 625)
Weld Overlay on all wetted parts.
All metallic coatings shall attend the specific requirements listed in item A.8.2.1.
All designs of soft ball valves shall consider the application of hard coating on seats / ball according:
Table A.31 – Specification of hard coating on seats / ball on soft ball valves
Pressure Class
VSL
150 300 600 900 1500 2500 10000
VSL-1 N/A
Tungsten Carbide
VSL-2 N/A or
Chrome Carbide
Tungsten Carbide
VSL-3 N/A or
Chrome Carbide
VSL-4 N/A
All designs of metal to metal ball valves shall consider the use of hard coating on seats / ball according:
Table A.32 – Specification of hard coating on seats / ball on metal to metal ball valves
- Rev. 11 - Page 35 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
Table A.32 – Specification of hard coating on seats / ball on metal to metal ball valves
Pressure Class
VSL
150 300 600 900 1500 2500 10000
VSL-1 Tungsten Carbide 2
Chromium
or
Electroplate 1
VSL-2 Chrome Carbide
VSL-3
Tungsten Carbide 2, Chrome Carbide 2 or Chrome-Nickel Spray and Fuse
VSL-4
1If requested by the manufacturer, it may be acceptable the use of tungsten carbide or chrome carbide
coating.
2 For valves which maximum design temperature is above 210ºC, it only shall be considered application
of chrome-nickel Spray and Fuse coating.
All hard coatings application shall attend the specific requirements listed in item A.8.2.2.
Table A.33 – Typical configurations for soft seated ball valves according material class
- Rev. 11 - Page 36 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
- Rev. 11 - Page 37 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
1 Partial clad may be requested in the VDS, and shall be according Table A.30.
2 The use of forging or casting shall be according VSL classification. For valves with NPS < 2, It shall be
considered only the use of forging material.
3 Hard Coatings may be requested in the VDS, and shall be applied according Table A.31.
Table A.34 – Typical configurations for metal to metal seated ball valves according material class
ASTM A105
or AISI 410
Carbon Steel ASTM A216 WCB +
+ Hard Coating 3
Partial Clad 1
- Rev. 11 - Page 38 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
A.7.1.8.1. Ball valves included in scope of S-562 shall comply with S-562, this Annex and following
requirements/modifications.
A.7.1.8.2. Design validation shall be as required by Table A.3.
A.7.1.8.3. Process fabrication for body materials shall be according Table A.7.
A.7.1.8.4. Table J.3 of S-562, sequence 7, shall be read as: Low-pressure pneumatic seat test at 80 psi (6 bar) to 100
psi (7 bar) per H.3.2 Type I.
A.7.1.8.5. For fluid services such as aromatic hydrocarbons, steam, methanol, amines, strong alkalis and some Freons,
Table A.21 and Table A.22 shall be used as reference to selection of suitable sealing material.
A.7.1.8.6. For classes 150 to 600, all sizes, and for classes 900 to 2500, sizes NPS 8 (DN 200), vents and drains shall
have double seal (axial outboard and radial inboard) parallel threads with locking ring. During loosening of the fitting, the
design configuration shall ensure pressure is relieved from the inboard seal without thread disengagement.
A.7.1.8.7. NDE, tests and documentation of each valve shall be according A.7.1.8.7.1 to A.7.1.8.7.4.
A.7.1.8.8. SDV, BDV, XV and ADV valves shall be fire tested. For other valves, fire type-tested certified design shall be
required according design premises.
A.7.2.1.1. It shall be considered a Metal to Metal seated design for all types of gate valve. Expanding gate valves may
have an additional non-metallic insert.
A.7.2.1.2. Whenever specified in the VDS, the manufacturer shall attend to the requirement of coating, such as metallic
coating, hard coating and/or organic coating specified for some parts and sealing surfaces, such as in the body, bonnet,
gate, seats, etc. In this case, the manufacturer shall attend the applicable requirements listed on item A.8.2.
A.7.2.1.3. Gate valves, with flanged or butt weld ends, shall have face to face dimensions according ASME B16.10.
A.7.2.1.4. End connections shall be according:
a) Flanged ends: according ASME B16.5 up to DN 600 (NPS 24) for ASME classes 150 to 1500, and up to DN
300 (NPS 12) for class 2500; according ISO 27509 for DN 400 (NPS 14) to NPS 600 (NPS 24) in ASME class
2500; according ASME B16.47 Series A from DN 650 (NPS 26) up to DN 1500 (NPS 60) for ASME Classes 150
to 600, and and from DN 650 (NPS 26) up to DN 1200 (NPS 48) for ASME class 900.
A.7.2.1.5. The gate skirts shall be designed to minimize seats wearing and maintain the alignment between gate and
- Rev. 11 - Page 39 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
A.7.2.2.1. The following standards shall be considered for the design of gate valves:
Class 800 and 1500 2500 10.000 psi 150 and 300 600 to 1500 2 500
ASME
Standard API 602 API 6A API 600 / IOGP S-611 a
B16.34 LTD
a
As applicable. See also A.7.2.5
A.7.2.3.1. All non-metallic seals shall be suitable for the pressure, temperature and service conditions specified in the
VDS.
A.7.2.3.2. The manufacturer of the valve shall guarantee together with your seals supplier(s) the necessary material
requirements for the non-metallic seals, in order to ensure that the designed seal system works properly during the
whole design life of the valve.
A.7.2.3.3. For solid wedge gate valves, the design shall consider the use of gaskets made of flexible graphite with inconel
wire for the stem seal.
A.7.2.3.4. The design of a slab gate valve shall consider the use of non-metallic seals, mounted on seats and stem,
according the materials specified in the VDS.
A.7.2.4.1. This item presents typical configurations for gate valves, as a result of combinations of materials and features.
The following configurations are considered to create a specific VDS.
A.7.2.4.2. The referred number of the typical configuration of a gate valve, shown on the first column of Table A.36,
Table A.37 and Table A.38, shall be considered as a part of the valve code, according item A.11.5.
- Rev. 11 - Page 40 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
Table A.36 – TRIM material configuration for solid wedge gate valves
ASTM A105
Trim Number 8 Stellite ASTM A276
or AISI 410
(API 600 / 602) (Co-Cr Alloy) (UNS S41000)
ASTM A216 Gr. WCB
ASTM A105
Trim Number 5 Stellite Stellite ASTM A276
or
(API 600 / 602) (Co-Cr Alloy) (Co-Cr Alloy) (UNS S41000)
ASTM A216 Gr. WCB
Carbon ASTM A350 LF2 Cl 1
Steel Trim Number 16 Stellite ASTM A276
or AISI 316
(API 600 / 602) (Co-Cr Alloy) (UNS S31803)
ASTM A352 Gr. LCB
ASTM A105 ASTM A276
ASTM A995 Gr. 1b ASTM A995 Gr. 1b
or (UNS S32550)
ASTM A216 Gr. WCB -
ASTM A276
+ ASTM A995 Gr. 4a ASTM A995 Gr. 4a
(UNS S31803)
Organic Coating
ASTM A182 Gr. F316
Stainless or Trim Number 16 Stellite
AISI 316 A276 316 / 316L
Steel ASTM A351 Gr. (API 600 / 602) (Co-Cr Alloy)
CF8M
ASTM A182 F51
ASTM A276
or - UNS S31803 UNS S31803
(UNS S31803)
ASTM A995 Gr. 4a
Duplex Steel
ASTM A182 F55
ASTM A276
or - UNS S32760 UNS S32760
(UNS S32760)
ASTM A995 Gr. 6a
ASTM B564 ASTM B564 ASTM B564 ASTM B637
Nickel Alloy -
(UNS N06625) (UNS N06625) (UNS N06625) (UNS N07718)
Bronze
ASTM B61 ASTM B61 ASTM B61
ASTM B61 -
(UNS C92200) (UNS C92200) (UNS C92200)
(UNS C92200)
Gray Iron ASTM B62 ASTM B62 ASTM B62
Uncommon -
ASTM A126 Cl. B (UNS C83600) (UNS C83600) (UNS C83600)
Materials
Nickel Aluminum
Bronze ASTM B148 ASTM B148 ASTM B150
-
ASTM B148 (UNS C95800) (UNS C95800) (UNS C63200)
(UNS C95800)
Obturator type
0 Solid wedge
1 Slab gate
2 Expanding gate
- Rev. 11 - Page 41 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
TRIM design
1 Standard TRIM
2 Alternative TRIM
3 Special TRIM
A.7.2.4.6. Gate valves included in scope of S-611 shall comply with S-611 and following requirements/modifications.
A.7.2.4.7. Design validation shall be as required by Table A.3.
A.7.2.4.8. Process fabrication for body materials shall be according Table A.7.
A.7.2.4.9. First paragraph of S-611 item H.3.5 shall be read as: Valves shall be tested with full pressure end thrust effect
to check the effectiveness of body joints and tightness as per Table H.5. Test shall be carried out with horizontal
flow bore and stem horizontal to demonstrate compliance with 5.6.3/5.6.5 (API 600/API 603). For this selected
valve from Table H.5, functional test in accordance with H 3.6.2, except step (a) (2), shall be carried out over five
cycles.
A.7.2.4.10. NDE, tests and documentation of each valve shall be according A.7.2.4.10.1 to A.7.2.4.10.4.
A.7.3.1.1. Check valves, with flanged or butt weld ends, shall have face to face dimensions according ASME B16.10.
A.7.3.1.2. End connections shall be according:
a) Flanged ends: According ASME B16.5 up to DN 600 (NPS 24), according ASME B16.47 Series A to DN 650 up
to 900 (NPS 26 up to 36), according ASME B16.47 Series B for DN 950 up to 1500 (NPS ≥ 38); for flanges
classes 600 and 900 the dimensions of flanges DN 950 up to 1500 (NPS ≥ 38) shall be according ASME B16.47
Series A;
A.7.3.1.3. For others materials not specified in the VDS, such as bolts, nuts, washers and lock pins, it shall be considered
the use of materials with similar corrosion resistance than the materials indicated for the internals.
A.7.3.1.4. Whenever specified in the VDS, the manufacturer shall attend to the coating, such as metallic coating, hard
coating and/or organic coating specified for some parts and sealing surfaces. In this case, the manufacturer shall attend
- Rev. 11 - Page 42 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
A.7.3.2.1. The following standards shall apply to the design of check valves:
Class 150, 200 800 and 1500 2500 150 and 300 600 900 and 1500 2500 10.000 psi
ASME
Standard MSS SP-80 API 602
B16.34 LTD
API 594, API 6D API 6A
A.7.3.3.1. For the design of soft seated dual plate check valve, the VDS contains indication about the non-metallic group
material that shall be considered in the valve design, in this case:
- Group A – Terpolymer of VF2, HFP e TFE with fluor content of ~ 67 - 70% or HNBR with %ACN between 36
and 40%. E.g.: Viton B (DuPont), Technoflon TN (Solvay Solexis);
Table A.40 – Seal group materials for soft seated dual plate check valve
Operating Design
Seals Temp. 1 Temp. 2 Seals Seals Group
Application RGD Suitable for
Group Min. Max. Min. Max. Materials Design Restrictions
(° C ) (° C ) (° C ) (° C )
1 Temperature range considered for continuous service without reducing the seals' economic life or its sealing capability.
2 Temperature range considered whether the seals may be exposed for a short period of time (transient temperature spike),
under a static condition (without operation), with a possible leakage but without permanently damaging the sealing system.
3 Hydrocarbons streams containing more than 25% aromatics.
A.7.3.4.1. This item presents typical configurations for check valves, as a result of combinations of materials and
features. The following configurations are considered to create a specific VDS.
A.7.3.4.2. The referred number of the typical configuration of a check valve, shown on the first column of Table A.41,
Table A.42 and Table A.43, shall be considered as a part of the valve code, according item A.11.5.
- Rev. 11 - Page 43 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
TRIM AA
Gray Iron ASTM A126 Cl B N/A N/A
(API 594)
Config.
# Type
0 Piston
1 Dual plate
2 Swing
3 Axial non-slam
- Rev. 11 - Page 44 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
4 Ball
Config.
# Type Body Construction
1 Primary TRIM (Soft) Wafer
2 Primary TRIM (Metal x Metal) Wafer
3 Secondary TRIM (Metal x Metal) Wafer
4 Alternative TRIM Wafer
5 Primary TRIM (Metal x Metal) Double Flanged Short Pattern
A.7.4.1.1. It shall be considered a Metal to Metal seated design for all types of globe valve.
A.7.4.1.2. Whenever specified in the VDS, the manufacturer shall attend to the requirement of coating, such as metallic
coating, hard coating and/or organic coating specified for some parts and sealing surfaces, such as in the body, etc. In
this case, the manufacturer shall attend the applicable requirements listed on item A.8.2.
A.7.4.1.3. Globe valves, with flanged or butt weld ends, shall have face to face dimensions according ASME B16.10.
A.7.4.1.4. End connections shall be according:
a) Flanged ends: According ASME B16.5 up to DN 600 (NPS 24) for ASME classes 150, 300, 600 and 900,
according ASME B16.47 Series A from DN 650 up to DN 1500 (NPS 26-60) for and from DN 650 up to DN 1200
(NPS 26-48) for ASME class 900.
A.7.4.2.1. The following standards shall apply to the design of globe valves:
A.7.4.3.1. This item presents typical configurations for globe valves, as a result of combinations of materials and
- Rev. 11 - Page 45 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
Config.
# Type
0 Bevelled disc
1 Angular
- Rev. 11 - Page 46 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
A.7.5.1.1. It shall be considered the following types of butterfly valves: Category A (concentric), Category B (Double
offset) and Category B (Triple Offset).
A.7.5.1.2. All butterfly valves category B with double offset shall consider a Soft seated design.
A.7.5.1.3. All butterfly valves category B with triple offset shall consider a Metal to Metal seated design.
A.7.5.1.4. Whenever specified in the VDS, the manufacturer shall attend to the requirement of coating, such as metallic
coating and/or hard coating specified for some parts and sealing surfaces, such as in the body or disc. In this case, the
manufacturer shall attend the applicable requirements listed on items A.7.5.4.3 and A.8.2.
A.7.5.2.1. The following standards shall apply to the design of butterfly valves:
Category A Category B
Wafer or Lug Wafer or Lug Flanged (Short Pattern) Flanged (Short Pattern)
Maximum Working
Class 150 up to 600 150 up to 300 600 150 up to 300 600
Pressure (MWP)
A.7.5.3.1. For the design of seats / stem seals, in butterfly valves Category A or B, the following materials shall be
considered:
Minimum Maximum
Type Material
Temp. (ºC) Temp. (ºC)
Category A NBR -10 +80
Category B (Double Offset) RPTFE -46 +260
Category B (Triple Offset) Graphite -240 +550
Note: Temperature values listed in Table A.48 represents the limits of use the non-metallic material on a butterfly valve
design.
- Rev. 11 - Page 47 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
A.7.5.4.2. For the design of butterfly valves category B (triple offset), it may be considered one of the following
configurations:
(a) Seal ring fixed to body & hard coating on disc (b) Seal ring fixed to disc & hard coating on body
Figure A.10 – Illustration of typical category B (triple offset) seat configurations
Whenever AISI 410 is considered as disc material for category B butterfly valves, it shall be applied ENP
coating on disc sealing surface.
On triple offset butterfly valves (category B), it shall be applied metallic coating on sealing surface (disc or
body, depending on configuration as described in Figure A.10). In this case, the use of Cobalt-Chromium (Co-Cr) weld
overlay or ENP are acceptable.
All metallic coatings application shall attend the specific requirements listed in item A.8.2.1.
- Rev. 11 - Page 48 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
Material Disc
Body Material Type Seats 1 Stem Seal Ring
Class Material
AISI 410
Category B ASTM A276
+ RPTFE N/A
ASTM A105 (Double Offset) (UNS S41000)
Carbon ENP
or
Steel ASTM A216 Gr. WCB
AISI 316 ASTM A564
Category B Graphite Laminated
AISI 316 + Type 630
(Triple Offset) with AISI 316
Hard Coating (UNS S17400)
ASTM B148 ASTM B865
NBR N/A
(UNS C95800) (UNS N05500)
ASTM A536
Gr 65-45-12 ASTM A276
NBR N/A
ASTM A536 Category A + (UNS S41000)
Ductile Iron Gr 65-45-12 (Concentric) PA Coating
ASTM A536
Gr 65-45-12 ASTM A276
NBR N/A
+ (UNS S31803)
PA Coating
Low
AISI 316 ASTM A564
Temperature Category B Graphite Laminated
ASTM A352 Gr. LCB AISI 316 + Type 630 H1150
Carbon (Triple Offset) with AISI 316
Hard Coating (UNS S17400)
Steel
ASTM A564
Stainless ASTM A351 CF8M
Category B
AISI 316 RPTFE Type 630 H1150
Graphite Laminated
Steel (Double Offset)
(UNS S17400)
with AISI 316
- Rev. 11 - Page 49 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
0 Category A Concentric
1 Category B Double offset (bi-eccentric)
2 Category B Triple offset (tri-eccentric)
Table A.51 – End connection configuration for butterfly valves category A (concentric)
Double
TRIM Maximum
Body Material Disc Stem Lug Wafer Flanged
Config. Pressure
(Short Pattern)
ASTM A536 ASTM B 148 ASTM B865
#1 250 psig 1 2 3
Gr 65-45-12 (UNS B95800) (UNS N05500)
ASTM A536
ASTM A536 Gr 65-45-12 ASTM A276
#2 150 psig 4 5 6
Gr 65-45-12 + (UNS S41000)
PA Coating
ASTM A536
ASTM A536 Gr 65-45-12 ASTM A276
#3 150 psig 7 8 9
Gr 65-45-12 + (UNS S31803)
PA Coating
Table A.52 – End connection configuration for butterfly valves category B (double / triple offset)
Config.
# Type
1 Lug
2 Wafer
3 Double Flanged (Short Pattern)
01 PVC
02 CPVC
03 FRP
A.7.6.2.1. The design of non-metallic ball valve shall consider the minimum pressure – temperature rating as follows:
- Rev. 11 - Page 50 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
Table A.54 – Minimum pressure (psig) – temperature rating for non-metallic ball valves
A.7.6.2.2. The design of non-metallic check valve shall consider the minimum pressure – temperature rating as follows:
Table A.55 – Minimum pressure (psig) – temperature rating for non-metallic check valves
Material
PVC CPVC
Temp.
23°C 150 150
30°C 150 150
35°C 150 150
40°C 144 146
45°C 137
50°C 128
55°C 119
60°C 110
N/A
65°C 101
70°C 92
75°C 83
80°C 74
A.7.6.2.3. The design of non-metallic butterfly valve shall consider the minimum pressure – temperature rating as
follows:
Table A.56 – Minimum pressure (psig) – temperature rating for non-metallic butterfly valves
Material
PVC CPVC
Temp.
23°C 150 150
30°C 132 140
35°C 115 129
40°C 97 119
45°C 108
N/A
50°C 98
- Rev. 11 - Page 51 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
Material
PVC CPVC
Temp.
55°C 87
60°C 77
65°C 66
70°C 56
75°C 45
80°C 35
A.8.1.1. SCOPE
A.8.1.1.1. All valves made from stainless steel duplex and/or super duplex casting (UNS J92205, UNS J93404 and UNS
J93380), without using bake sand foundry process, shall attend the minimum requirements listed herein for design,
production, inspection and acceptance.
A.8.1.1.2. The requirements listed herein are applicable for axial, ball, gate, globe and check type flanged valves, for all
pressure classes, with NPS ≥ 2.
A.8.1.2. DOCUMENTATION
A.8.1.2.1. The Data Book of the valve shall contain all certificates related to all parts, according:
- chemical requirements;
- mechanical tests (tension, hardness and impact);
- metallurgic tests (resistance to localized corrosion and metallography for phase treatment counting and thermal
treatment of the pilot casting);
- inspection reports (visual, using penetrant liquid and radiography);
- all thermal treatments;
- all WPS for defect repairing, approved by PETROBRAS or by a Classification Society indicated by
PETROBRAS.
- welders qualification certificates, for repairs execution;
- cavity mapping, for bigger repairs of each part of the valve;
- welding report, for repairs of each part of the valve.
A.8.1.3.1. The duplex steel used for manufacturing casting valves, for use in piping specifications B16, C16, E16, G16
or G16P, shall be in accordance with ASME SA-995 or ASTM A 995 Grade 4A (UNS J92205 or ACI CD3MN).
A.8.1.3.2. The super duplex steel used for manufacturing casting valves, for use in piping specifications B12, C12, H12,
G12, G12P or J12, shall be in accordance with ASME SA-995 or ASTM A 995 Grade 5A (UNS J93404 or ACI CE3MN).
A.8.1.3.3. The super duplex steel used for manufacturing casting valves, for use in piping specifications B13 or C13,
shall be in accordance with ASME SA-995 or ASTM A 995 Grade 6A (UNS J93380 or CD3MWCuN).
- Rev. 11 - Page 52 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
A.8.1.3.4. The representative sample of the chemical requirements of the valve shall be collected from the pouring ladle.
A.8.1.3.5. A representative sample for carbon, sulfur and nitrogen contents shall be collected from the furnace before
pouring into the ladle.
A.8.1.3.6. The addition of Niobium to the cast shall be avoided. The maximum allowable content of Niobium shall be
0,060% at the chemical requirements of the cast.
A.8.1.3.7. Adding Aluminum to the run shall be avoided. The maximum allowable content of Aluminum to the final
chemical requirements shall 0,030%.
A.8.1.3.8. The levels of Nitrogen shall preferably be in the range of 0,20% up to 0,25%.
A.8.1.3.9. All consumables for the welding process shall have certification of their chemical requirements guaranteeing
maximum levels of Niobium of 0,060%.
A.8.1.3.10. The chemical analysis of the elements shall be made in calibrated equipment according certified standards.
A.8.1.3.11. Whenever more than one ladle is used for one mold, the metal founded in each ladle shall be in accordance
with the chemical specifications for the required level.
A.8.1.4.1. The procedure for solubilization heat treatment used to the super duplex steel casting valves shall be in
accordance with ASME SA-995 or ASTM A 995 Grade 5A (UNS J93404 or ACI CE3MN) and Grade 6A (UNS J93380
or ACI CD3MWCuN).
A.8.1.4.2. Solubilization heat treatment is the only acceptable treatment for production of the super duplex steel casting
valves.
A.8.1.4.3. The maximum number of solubilization heat treatments allowed for a single valve is limited to three (03) at
foundry and one (01) at machining shop. If more heat treatments are needed, the manufacturer shall submit it for
PETROBRAS approval.
A.8.1.4.4. All heat treatments shall be monitored through thermocouples in the heat charge and in the furnace, and its
register shall be inserted into the Data Book.
A.8.1.4.5. Welding repair is not allowed before heat treatment.
A.8.1.4.6. Whenever solubilization heat treatment is necessary after casting, it shall be performed in order to avoid
distortions of the piece. It may be executed only one time.
A.8.1.4.7. The soaking time depends on the prior experience of the manufacturer, and shall guarantee full solubilization
of the inter-metallic phases and the precipitates through the thickest dimension of the piece without causing dimensional
distortions.
A.8.1.4.8. The pilot casting shall have possibility of extracting a test specimen for metallographic tests, which can be in
any direction (longitudinal or transversal), representing a central session of the thickest part of the piece, according
supplementary requirement S26.2 of ASTM A703, in order to verify the effectiveness and adjustment of the soaking time
of the solubilization heat treatment. The results of this metallographic shall be part of the Data Book.
A.8.1.4.9. The result of the metallographic test shall indicate absence of inter-metallic phases and undesired precipitates
– notably, the sigma phase, carbides and nitrates – in a 200X magnification, as well as indicate a level of ferrite in the
range of 35 to 55%, according ASTM E 562.
A.8.1.4.10. For each casting with weight ≥ 300 kg, specimens for mechanical and metallurgical tests shall be attached,
according ASTM A703. These test specimens shall remain attached to the casting until the last thermal treatment. For
- Rev. 11 - Page 53 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
pieces with weight < 300 kg, a test specimen per run is accepted.
A.8.1.5.1. The mechanical and metallurgical tests shall be done after the last the solubilization heat treatment, and
before machining the casting.
A.8.1.5.2. The mechanical tests to be performed are tension, hardness and impact (Charpy-V) testing, according ASTM
A370.
A.8.1.5.3. The test specimens shall be obtained from cast test blocks, according ASTM A703. These blocks shall go
through all the solubilization heat treatments before collecting the specimens for analysis.
A.8.1.5.4. One (01) test specimen shall be extracted for the tension test. The minimum acceptable values are according
Table A.57 (ref. ASME SA-995 or ASTM A995).
Grade 4A 5A 6A
UNS J92205 J93404 J93380
Tensile Strength, ksi [Mpa] {kg/mm²} 90 [620] {63} 100 [690] {70} 100 [690] {70}
Yield Strength, ksi [Mpa] {kg/mm²} 60 [414] {42} 75 [515] {53} 65 [450] {46}
Elongation in 2” [50 mm], % 25 18 25
A.8.1.5.5. Three (03) test specimens shall be collected for the impact tests (Charpy-V). The tests shall be performed at
a temperature of -46°C. The minimum values of absorbed energy shall be of 45J for an average of the three test
specimens and 35J for each one of the test specimens.
A.8.1.5.6. The hardness tests shall be run on a test specimen collected from a test block, in a point representative of
the central part of the thickest part of the casting, according to the supplementary requirement S26.2 of ASTM A703.
The maximum hardness shall not be above 32 HRC (or 310 HB or 330 HV10), considering the average of three
measurements. Castings with weight < 300 kg shall be tested individually and shall render specific hardness values less
or equal to the pilot casting on the surface.
A.8.1.5.7. A test specimen shall be collected from the pilot casting, in order to perform the corrosion tests according
ASTM G48 Method A. The test shall be run for 24 hours at a temperature of 50°C. The acceptance criteria shall be
according Grade 5A (UNS J93404 or CE3MN) and Grade 6A (UNS J93380 or CD3MWCuN):
- no pites located at 20 X magnification;
- loss of mass less than 4,0 g/m².
A.8.1.5.8. The test to define the levels of ferrite shall be performed according ASTM E562. The test specimen shall be
collected from a cast test block connected to a casting that would represent a certain run. The acceptable range is 35
up to 55% of ferrite.
A.8.1.6.1. VISUAL
visual inspection shall be made on all castings before and after each solubilization heat treatment, after
pre-machining (whenever applicable) and the final machining.
- Rev. 11 - Page 54 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
all accessible surfaces, internal and/or external, shall be visually examined, comparing acceptable
discontinuities and superficial finishing according MSS SP-55 or comparison rules of Steel Casting Research and
Trading Association (SCRATA) adopted in ASTM A802, or other standard considered equivalent by a set deal between
the manufacturer and PETROBRAS.
the levels of acceptance for visual inspections are set in ASTM A802, and are:
- level II, for non-machined surfaces;
- level III, for surfaces to be machined, as long as the machining completely eliminates the discontinuities.
all castings that presents, in one or more surfaces, independent of how serious or how extensive the defects
are, or whether it allows repairs using welding or not, the following defects shall be considered UNACCEPTABLE:
- chaplet - discontinuity due to the incomplete fusion of the supports of chills and cores;
- shrinkage - cavity resulting from contraction while solidifying;
- shift - discontinuity due to displacement of contact edges of the molding boxes;
- misrun - insufficient foundered metal in the casting;
- shut metal - discontinuity due to the encounter of two currents of metal that have not been well mixed;
- veins - discontinuity due to movement or cracking of the sand mold;
- rat tail - depression on the surface of the piece caused by waves or failure in the mold surface;
- internal chills - discontinuity caused by incomplete fusion of devices used to increase the cooling rate in
determined places.
A.8.1.7.1. LPI shall be performed by Level 2 inspectors qualified by the “Sistema de Nacional de Qualificação e
Certificação” (National System of Qualification and Certification) in Non Destructive Testing (SNQC/END), or by another
bureau according to ISO 9712 or EN 473.
A.8.1.7.2. LPI shall be performed on every produced casting, on all accessible surfaces (internally and/or externally),
after the final machining. All castings that make up the valves of the same order shall undergo inspection using Liquid
penetrant.
A.8.1.7.3. LPI shall be performed according ASTM E165.
A.8.1.7.4. indications shall be classified according APPENDIX 8 (8-3) of ASME SEC VIII Div. 1.
A.8.1.7.5. The acceptance criteria shall be according ASME SEC VIII DIV 1 APPENDIX 7.
A.8.1.8.1. radiographic inspection shall be executed by Level 2 inspectors qualified by the “Sistema de Nacional de
Qualificação e Certificação” (National System of Qualification and Certification) in Non Destructive Testing (SNQC/END),
or by certification according ISO 9712 or EN 473.
A.8.1.8.2. radiographic inspection shall be performed on the pilot casting (body, cap and shutter), after conclusion of
heat treatment. For parts which pressure classes are 900 and above, it is mandatory to perform radiographic inspection
on 100% of the final pieces, in the critical regions defined in ASME B16.34.
A.8.1.8.3. radiographic inspection shall be performed according ASTM E94 and ASTM E1030.
A.8.1.8.4. The list of parts to be radiographed and the acceptance criteria shall be according ASME B16.34.
- Rev. 11 - Page 55 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
A.8.1.8.5. If all indications are classified as ACCEPTABLE, no other piece than the pilot casting shall be radiographed.
A.8.1.8.6. If one or more conditions were classified UNACCEPTABLE, the pilot casting shall be fixed or scrapped, a
report shall be issued with causes analyses and solutions, and another piece shall be radiographed. If the second piece
is approved, no more piece needs to be radiographed. If the second piece also presents UNACCEPTABLE indications,
all pieces equal to the pilot casting of the order shall be radiographed in the areas rejected for the pilot casting and for
the second casting. The second casting and the subsequent piece of the order shall be repaired whenever identified an
unacceptable indication, otherwise it shall be rejected.
Defects by
Thickness < 2” 2 ≤ Thickness < 4 1/2” 4 1/2” ≤ Thickness < 12”
Thickness
Standards ASTM E446 ASTM E186 ASTM E280
Porosity (A) A2 A3 A3
Sand or Slag (B) B3 B3 B3
Shrinkage
CA2 CA3 CA3
Porosity (CA)
Shrinkage
CB3 CB3 CB3
Porosity (CB)
Shrinkage
CC3 CC3 CC3
Porosity (CC)
Shrinkage
CD3 - -
Porosity (CD)
Cracks (D) None None None
Shrinkage
None None None
Cracks (E)
Inserts (F) None None None
A.8.1.9.1. Ultrasonic inspection shall be executed by Level 2 inspectors qualified by the “Sistema de Nacional de
Qualificação e Certificação” (National System of Qualification and Certification) in Non Destructive Testing (SNQC/END),
or by certification according ISO 9712 or EN 473.
A.8.1.9.2. Ultrasonic inspection shall be performed according ASTM A388 (forgings) and ASTM A609 (castings).
A.8.1.9.3. Acceptance criteria shall be according ASME B16.34.
A.8.1.10. REPAIRS
- Rev. 11 - Page 56 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
A.8.1.10.5. Before any repair, the surface shall be inspected by visual and preferably magnetic particle and liquid
penetrant inspection.
A.8.1.10.6. Twenty four hours (for hydrogen diffusion) after the last welding repair, it shall be repeated the same NDT
used to identify the defect. For extensions over 50 mm length and over 20% thickness depth a ultrasonic test or
radiography shall be executed. Acceptance criteria shall be according ASME B16.34.
A.8.1.10.7. It is mandatory to perform post weld heat treatment for carbon steel or solubilization on stainless steel when:
A.8.1.10.8. Test Specimens for Counter-Sample - Chemical Analysis and Mechanical Testing: the minimum period
established for storage, by the foundry, of test specimens for sample are twelve (12) months.
A.8.1.11. MACHINING
A.8.1.11.1. The machining of the casting shall only be executed after heat treatment.
A.8.1.11.2. No kind of machining may be done after hydrostatic test.
A.8.1.11.3. Machined surfaces shall be according valve design as tolerance and rugosity.
A.8.1.11.4. No kind of metallurgical changing may occur caused by heating during machining. If necessary shall be a
metallographic replica exam.
A.8.1.11.5. Liquid penetrant on seal surface shall be ZERO defect.
A.8.2. COATINGS
A.8.2.1. METALLIC COATING
Whenever specified in the VDS, it shall be applied on the indicated parts an ENP coating obtained by
chemical reactions leading to a plating composed of 90% Nickel and 10% Phosphorus. This coating shall be in
accordance with ASTM B 733 attending classification SC4, Type V, heat treatment Class 2.
The minimum thickness of the ENP coating shall be 0,003 inch (75 μm).
All components shall be traceable for the details of the coating procedure, coating conditions and date of
application.
The manufacturer shall issue inspection certificates of the ENP coating, and each certificate shall identify
the plant where the treatment is performed and the history of the process. Also, it shall list all serial numbers of the parts
coated together with the material grades and the overall geometry of those parts.
Whenever specified in the VDS the term Stellite, it shall be applied a weld overlay of cobalt-chromium (Co-
Cr) alloy on indicated parts.
The specification of the cobalt-chromium (Co-Cr) alloy shall fulfil the requirements of the design standard
indicated in the VDS.
For valves with DN < 2 , which is not possible to apply cobalt-chromium (Co-Cr) weld overlay, the
- Rev. 11 - Page 57 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
Whenever specified in the VDS, it shall be applied a minimum of 3,0 mm thick weld overlay in stainless
steel grade 316L on seat pockets and stem seal contact faces on the body.
For floating ball valves, this requirement is not applicable to the seat pockets as soon as the seat ring is
made of an integral, solid thermoplastic material (i.e.: valves having a fixed seat), but it applies to stem sealing areas in
all cases (for floating ball valves having also a floating seat design, the seat-to-body sealing area shall consequently be
overlaid).
For valves with DN < 2, which is not possible to apply stainless steel weld overlay, the manufacturer shall
consider to use integral parts of stainless steel or CRA alloy.
For the parts which materials are made of stainless steel, duplex, super duplex or solid Inconel 625 there
is no need to apply an overlay.
Dilution on welded surface shall not exceed 10% of base metal.
Whenever specified in the VDS the term Inconel 625, it shall be applied a weld overlay of a nickel alloy
UNS N06625 on indicated parts.
The areas of such parts that shall be welded are indicated in the VDS. The manufacturer shall attend to the
requirement of partial or full cladding.
The weld overlay thickness shall be sufficient in order to obtain a minimum of 3,0 mm thick protective layer
in the final machined condition.
For valves with DN < 2, which is not possible to apply Inconel 625 weld overlay, the manufacturer shall
consider to use integral parts of Inconel 625.
For the parts which materials are made of solid Inconel 625 there is no need to apply an overlay.
Dilution on welded surface shall not exceed 10% of base metal.
Whenever specified hard coating in the VDS, a hard coating of chromium electroplate may be applied on
the indicated parts of a metal to metal ball valve, as described in Table A.32.
Whenever specified hard coating in the VDS, a hard coating of chrome carbide may be applied on the
indicated parts.
When applicable, hard coating of chrome carbide shall be applied by High Velocity Oxy-Fuel (HVOF)
process.
The hard coating of chrome carbide shall achieve a minimum thickness of 200 μm after grinding and
lapping.
- Rev. 11 - Page 58 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
The hard coating shall be carefully applied and inspected to ensure that the finish is smooth, fine grained,
adherent, and free from blisters, pits, nodules, indication of burning, edge buildup, and other defects.
The hard Coating thickness shall be measured to confirm the results of it against the specified thickness.
Whenever specified hard coating in the VDS, a hard coating of tungsten carbide may be applied on the
indicated parts.
When applicable, hard coating of tungsten carbide shall be applied by High Velocity Oxy-Fuel (HVOF)
process.
The hard coating of tungsten carbide shall achieve a minimum thickness of 200 μm after grinding and
lapping.
The hard coating shall be carefully applied and inspected to ensure that the finish is smooth, fine grained,
adherent, and free from blisters, pits, nodules, indication of burning, edge buildup, and other defects.
The hard coating thickness shall be measured to confirm the results of it against the specified thickness.
Whenever specified hard coating in the VDS, a hard coating of chrome-nickel basis with metallurgical
bonding may be applied on the indicated parts.
When applicable, hard coating of chrome-nickel basis with metallurgical bonding shall be applied by Flame
Spray and Fuse process.
The hard coating of chrome-nickel spray and fuse shall achieve a minimum thickness of 500 μm after
grinding and lapping.
The hard coating shall be carefully applied and inspected to ensure that the finish is smooth, fine grained,
adherent, and free from blisters, pits, nodules, indication of burning, edge buildup, and other defects.
The hard Coating thickness shall be measured to confirm the results of it against the specified thickness.
The use of valves with organic coating may be considered as option for specific service applications, such
as with seawater service.
Whenever applicable, the pipe specification (spec) may present an organic coated valve code as an option.
Only ball, gate and globe valve types classified as VSL-1 and VSL-2 may consider the use of organic
coating.
The VDS of organic coated valve shall indicate/allow, as principle, the application of organic coating only
in the body/closure material of the valve.
For small size valves (e.g.: NPS < 3), when organic coating is not applicable, the body may be made of a
material with the same corrosion resistance of the materials specified for the internals.
The specification of the organic coating shall be according Annex F of DR-ENGP-I-1.1.
RTJ flanges may be organic coated, except the ring groove which shall attend the orientation indicated in
the pipe specification (spec).
- Rev. 11 - Page 59 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
The use of valves with polyamide (PA) coating may be considered as option for specific service applications,
such as with seawater service.
Whenever applicable, the pipe specification (spec) may present an polyamide (PA) coated valve code as
an option.
Only concentric butterfly valves (Category A) classified as VSL-1 may consider the use of polyamide (PA)
coating.
The VDS of polyamide (PA) coated valve shall indicate/allow, as principle, the application of polyamide
(PA) coating only in the disc material of the valve.
The acceptable specifications of the polyamide (PA) coating are PA 11 and PA 12.
A.8.3.1. All materials listed in the VDS shall be considered as standardized materials for valve parts, but are not exclusive
solutions. Therefore, the valve manufacturer may propose alternative materials (equivalent or better), conditioned to
PETROBRAS approval.
A.8.3.2. For a material to be accepted as equivalent or better, it shall have the same or better mechanical (i.e. yield
strength, hardness, etc.) and anti-corrosive properties (measured by PREN), be suitable for temperature range
presented in the VDS whilst not being susceptible to phenomenon such as brittle fracture or stress corrosion cracking.
A.8.3.3. Charpy impact testing is required for all materials, considering minimum temperature listed in ASME B31.3,
section 323 or as listed in the VDS, whichever is lower. All metallic materials shall be suitable for minimum temperature
service of -29°C.
A.8.3.4. Some examples of alternative materials are:
A.8.3.4.1. For pressure-containing parts, forging materials are acceptable in place of casting materials, but not vice-
versa.
A.8.3.4.2. For remaining internal parts (i.e.: non pressure-containing), forgings and castings are interchangeable as long
as they have the same desired properties (i.e.: mechanical properties, corrosion resistance, maximum or minimum
hardness, and other properties as applicable).
A.8.3.4.3. Superduplex (UNS S32760) may be used as replacement for duplex (UNS S31803), but not vice-versa.
A.8.3.4.4. Superduplex and duplex steels shall not be used for chlorinated seawater services (SW).
A.8.3.4.5. Nickel Aluminum Bronze (UNS C95800) may be used as replacement for bronze B62 (UNS C83600), but not
vice-versa.
A.8.3.4.6. Higher mechanical strength alloys such as ASTM A694 F60 or ASTM A694 F65 are acceptable instead of
ASTM A105 or ASTM A216 Gr WCB. For Inconel cladded valves used for sour service, the base material shall be NACE
compliant.
A.8.3.4.7. Superduplex and duplex steels may be replaced by carbon steel with 3 mm of Inconel 625 overlay, and vice-
versa if low temperature requirements are satisfied. Additionally, the pressure-temperature rating shall be validated.
A.8.3.4.8. Austenitic steels with PREN number less than that of 316/316L shall not be used on offshore facilities (e.g.:
AISI 304 and AISI 304L stainless steel materials shall not be used).
A.8.3.4.9. Internal parts made of martensitic stainless steels (e.g.: AISI 410) may be replaced by higher chromium alloys
- Rev. 11 - Page 60 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
A.8.3.4.12. Low temperature carbon steel parts (i.e.: ASTM A350 LF2, ASTM A350 LF3) may be used in lieu of regular
carbon steel parts (e.g.: ASTM A105, ASTM A216 WCB).
A.9.1.1.1. The ITP shall be issued by the supplier and submitted to PETROBRAS or EPC contractor approval.
A.9.1.1.2. The ITP shall allow the identification of stages, through the valve production cycle, where it shall be done
checks or inspections, including those carried out by material or service suppliers.
A.9.1.1.3. The ITP shall indicate the types of examinations, tests or checks to be made, as well as procedures and/or
applicable instructions, acceptance criteria and issued records.
A.9.1.1.4. The ITP shall contain register of critical quotas as defined by the manufacturer, including, at least,
standardized quotas in the construction and design standards of valves.
A.9.1.1.5. The ITP shall contain the procedures and instructions for inspection of all expected activities.
A.9.1.1.6. The inspection shall be performed by PETROBRAS or EPC contractor.
A.9.1.2.1. The receiving inspection shall be performed without causing damages to the package and without
compromising the preservation of the valves.
A.9.1.2.2. It shall be checked the valve and its components as the Data Book, identification (e.g. valve serial number,
actuator serial number, pressure class, etc.) and manufacturer manual for handling, storage and preservation.
A.9.1.2.3. After verifying the documentation and attesting its conformity, the packed shall be stored according item A.10.
The execution of NDT shall follow specific requirements, according type of material:
- Rev. 11 - Page 61 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
Chemical Carbon
Manganese Phosphorus Sulfur Silicon Nickel
Composition (max.)
ASTM A522 Type I 0,06 0,59 < 0,005 < 0,001 0,28 9,08
- Rev. 11 - Page 62 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
- all valves specified for hydrogen sulfide service shall be in strict accordance with the requirements of the ISO
15156;
- visual inspection shall be according to ASME BPV section V. The acceptance criteria shall be according to MSS
SP-55 specification;
- liquid penetrant and magnetic particles testing shall be according to ASME BPV section V. The acceptance
criteria shall be according to ASME B16.34 specification for class pressure up to 600#. For higher class
pressures the acceptance criteria shall be according to ASME B16.4, with the exception that no linear indication
shall be accepted;
- visual inspection shall be according to ASME BPV section V. The acceptance criteria shall be according to
ASME B16.34 specification;
- radiographic examination shall be according to ASME BPV section V and ASTM E94. The acceptance criteria
shall be according to ASME B16.34 specification;
- for castings valves NDT examinations shall focus on critical areas.
A.9.2.1. The design validation of a valve is requested according its VSL classification, as presented as follows:
Design Validation No Design analytical approval Design validation test approval (PVT)
A.9.2.2. For VSL-1 valves, no design validation is required. In this case, the manufacturer shall perform the design and
manufacture the valve attending all requirements listed in the applicable standards (e.g.: API 6D, API 6A, etc.).
A.9.2.3. For VSL-2 valves, design validation is required at documentation level. In this case, the manufacturer shall have
an analytical approval of the valve design. To attend this kind of design validation, the manufacturer shall submit for
PETROBRAS approval:
- Certificate of approval, issued by a 3rd party, referred to an analytical approval of the valve design, according
normative requirements (e.g.: NBR 15827, API 6D, API 6A, API 600, API 609, etc.); or
- A valid API monogram of the valve design, complying to all normative requirements of quality and design.
NOTE: In case the manufacturer has already performed a PVT test in the past on a representative prototype of the valve
design or on a valve which scaling may be considered valid, the requirement of design analytical approval may be
demonstrated by the certificate of approval. This certificate, referred to the execution to this PVT test, shall be issued by
a 3rd party.
A.9.2.4. For VSL-3 and VSL-4 valves, design validation is required at PVT test execution level. In this case, the
manufacturer shall perform all PVT tests on a representative prototype of the valve that will be supplied.
- Rev. 11 - Page 63 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
NOTE: The manufacturer is free of charge on performing the PVT test, in case it is presented a certificate of approval,
issued by 3rd party, referred on a PVT test performed in the past, on a representative prototype of the valve that will be
supplied or on a valve which scaling may be considered valid.
A.9.2.5. In the case of PVT test execution, the following Standards may be considered to the test:
- NBR 15827; or
- API 6A, considering PSL 3G, PR2 (Appendix F); or
- API 6AV1.
NOTE: In case of missing technical requirements, including acceptance criteria (e.g.: ball valve on API 6A), the PVT test
procedure shall be elaborated from better suited standards such as NBR 15827, and submitted to PETROBRAS
approval.
A.9.2.6. For a supply of a fire tested valve, the manufacturer shall also present a certificate of approval, issued by 3rd
party, complying to ISO 10497.
A.9.2.7. For a supply of a fugitive emissions valve, the manufacturer shall also present a certificate of approval, issued
by 3rd party, complying to ISO 15848.
A.9.3.1.1. The manufacturer shall consider the use of the following test medium:
For all tests with liquid: It shall be used fresh water with an addition of corrosion inhibitor.
NOTE: The chloride content of test water in contact with austenitic and duplex stainless steel wetted components of
valves shall not exceed 30 μg/g (30 ppm by mass) and the water temperature shall not be greater than 38°C (100°F)
during the testing period.
For high pressure gas tests: It shall be used dry nitrogen (N2).
For low pressure gast tests: It may be used dry air or nitrogen (N 2).
A.9.3.2.1. The manufacturer shall attend all requirements herein stated for the design and assembly of the test bench
dedicated to perform the FAT tests of the valve / actuator.
A.9.3.2.2. It shall be considered, as minimum, the use of the following equipment:
a) Test Panel with devices for manual and automatic operation, provided of pressure transmitters, digital indicators
or controllers, pressure meters, solenoid valves, relays, end-of-stroke indicators, cycles counter, etc., as well as
hydraulic systems (hydraulic units, etc.) compatible with the flows and test pressure levels for the valve / actuator
which will be tested.
d) Torque tool.
- Rev. 11 - Page 64 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
e) Data acquisition system, with capacity to adequately record the values of pressure and / or torque during test
execution.
A.9.3.2.3. The manufacturer shall take attention to the adequacy of protection for personnel carrying out the testing, in
the event of failure of a valve, connection or equipment during the test. Additional caution shall be taken whenever high
pressure gas tests are required.
A.9.3.3.1. During execution of any valve cycle, the following pressure ports shall be monitored / registered:
e) Valve stroke
A.9.3.4.1. The test bench shall have the capacity to monitor eventual leakages and allow to measure the volume in order
to allow verification of the acceptance criteria.
A.9.3.4.2. Hydraulic lines must be, whenever technically possible, built with short stainless steel tubing, to increase the
sensitivity to leakage detection. With the same purpose a procedure for purging the air of the valve body, the actuator
and the test panel must be foreseen. This procedure shall be approved by PETROBRAS.
A.9.3.4.3. During sealing tests with liquid, whenever visual observation of leakage in a direct way is not possible,
leakages can be monitored by pressure variation.
A.9.3.4.4. In case of leakage identification by pressure variation, one example of a method of quantifying sensitivity of
the test bench would be the creation of a “leakage”, small and controlled, where the leaked volume variation would be
co-related with the pressure drop generated by this “leakage”, for each test condition (pressure value, upstream lines,
downstream, ambient temperature, etc.).
A.9.3.4.5. Detection of a leakage shall be associated with the identification of a continuous pressure variation, without
occurring its stabilization along the time and since the effects of temperature variation can be disregarded (or
compensated). Thus, the pressure drop in an upstream line or pressure rise in a downstream line , without stabilization
of these pressure variations shall be considered as leakage.
A.9.3.4.6. In case of leakage identification by using level variation in a capillary, its diameter shall be compatible with
the capacity of identifying small leakages / volumes.
A.9.3.4.7. Pneumatic shell test shall be performed using inert gas, such as mixture of 99 % nitrogen with a 1 % helium,
tracer measured using a mass spectrometer, in order to guarantee leakage detection. Alternatively, if nitrogen (100%)
is used as test medium, the valve shall be submerged.
A.9.3.4.8. In case of monitoring gas leakage at the pressure ports, for higher and constant leakages it shall be
considered the use of flowmeters operating inside 20% to 80% of the nominal capacity of it.
A.9.3.4.9. For monitoring gas leakage on pressure ports for smaller or inconstant leakages it shall be performed by using
- Rev. 11 - Page 65 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
scale burette where a flexible hose is inserted totally on a burette (or at least above the meniscus) and the set is
submerged on a transparent aquarium filled with clean water. Monitoring of leakage shall be done by registering the
displacement of the meniscus line inside the burette, which can be seen through the aquarium.
A.9.3.4.10. Before each type of test, the manufacturer shall present the test bench set-up in order to demonstrate that it
is assembled on a correct way to perform the tests and monitor eventual leakages. The following items shall be
concerned during this presentation:
a) It shall be verified that the pressure source is connected to the correct pressure port.
b) It shall be verified that all test devices are properly assembled, such as if flanges and fittings are tightened,
check of instrumentation valves position (fully opened or fully closed), identification of hoses (which shall be in
a good shape, without creases, holes or tears), etc.;
A.9.3.5.1. All manual and actuated valves shall be subjected to a Factory Acceptance Test (FAT) prior to delivery and/or
shipping the valve.
A.9.3.5.2. It shall be considered the execution of FAT for the valve and its actuator.
A.9.3.5.3. Otherwise agreed, the FAT shall be performed with the actuator assembled onto the valve.
A.9.3.5.4. A functional test of valve + actuator shall be considered in order to guarantee adequate performance of the
set.
A.9.3.5.5. Valves wich design contains fugitive emissions requirement shall also perform additional FAT tests according
item A.9.3.6.
A.9.3.5.6. HIPPS valves shall also perform additional FAT tests according item A.9.3.7.
A.9.3.5.7. Whenever specified in the purchase order and/or Contract to comply with “Specific Inspection Requirement
for Industrial Valves - ET-0000.00-0000-972-P8L-023”, the manufacturer shall attend the specific requirements of
pressure tests listed in item 5.12 of ET-0000.00-0000-972-P8L-023.
NOTE: Any other conflict between ET-0000.00-0000-972-P8L-023 and this document shall be presented for
PETROBRAS evaluation.
A.9.3.5.8. The FAT of bronze globe valves shall follow MS SP-80. The FAT of other globe valves shall follow BS 1873 /
BS 12266 requirements, and applicable tests listed in these Standards shall be performed.
A.9.3.5.9. The FAT of butterfly valves (except to the triple offset design) shall follow API 609 / API 598 requirements,
and applicable tests listed in these Standards shall be performed.
A.9.3.5.10. The FAT of ball, gate, check, plug, axial and triple offset butterlfy valves shall follow:
Pressure tests according the respective QSL requirement for each VSL classification:
- Rev. 11 - Page 66 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
QSL-3
QSL QSL-2 QSL-3 QSL-4
(Note 1)
Note 1 – For liquid service application, it may be considered QSL-2, except for hydrocarbon.
a) For VSL-1 valves, it shall be performed pressure tests according API 6D QSL-2 requirements.
b) For VSL-2 valves, it shall be performed pressure tests according API 6D QSL-3 requirements. For liquid service
application, it shall be performed pressure tests according API 6D QSL-2 requirements.
c) For VSL-3 valves, it shall be performed pressure tests according API 6D QSL-3 requirements.
d) For VSL-4 valves, it shall be performed pressure tests according API 6D QSL-4 requirements.
In addition to the pressure tests required by Table A.61, the FAT of ball valves shall consider the execution
of the following supplementary tests listed in Annex H of API 6D: H.5, H.6, H.7, H.8, H.9, H.11.
NOTE: Otherwise agreed, the supplementary tests H.9 and H.11 shall be performed using gas as test medium.
The acceptable leakage rate for the tests shall be according API 6D, except to:
a) Hydrostatic seat test and low-pressure gas seat test of metal seated valves: the acceptable leakage shall be
ISO 5208 Rate B. For DBB tests the acceptable leakage is 2 X B.
b) High-pressure gas seat test of metal seated valves: the acceptable leakage rate shall be 2 X C (two times ISO
5208 Rate C). For DBB tests the acceptable leakage is 4 X C.
NOTE: Whenever DBB feature is required for the valve design at closed or closed & opened position, it shall be
considered the execution of DBB test on both conditions.
c) Triple offset butterlfy valves: The acceptable leakage rate for all HP/LP sealing (i.e.: seat) tests shall be
ISO 5208 Rate A.
Prior to perform the drive train strength test, listed in item H.7 of API 6D, the manufacturer shall provide
the following information:
a) Drive train engineering data (i.e.: stem calculation), demonstrating that the design thrust or torque for all drive
train calculations is at least two times the breakaway thrust or torque of the valve (i.e.: maximum thrust or torque
required to operate a valve at maximum pressure differential).
b) Actuator engineering data (e.g.: gearbox, hydraulic, etc.), demonstrating that proper safety factor has been taken
into account.
c) Test fixture design data, in order to guarantee that the test fixture used to block the obturator is able to withstand
the loads of the test and it would not damage the surface of the parts in contact (i.e.: ball / seats edges, sealing
region).
d) The selected torque value (acc. item H.7 of API 6D) that will be applied on the drive train strength test. If the
valve actuator (e.g.: gearbox, hydraulic, etc.) is used to generate the torque test, it shall be checked the values
- Rev. 11 - Page 67 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
of maximum output torque of the actuator and the selected torque value for the test, in order to confirm its
compatibility.
NOTE: The drive train strength test shall be performed prior to the sealing tests (i.e.: seat test) and it may be done in
only one valve of the lot, per nominal, per actuator type (e.g.: gearbox, hydraulic, etc.), and per pressure class,
conditioned to:
A.9.3.6.1. Whenever specified in the VDS that the valve shall be fugitive emissions approved, a minimum of one valve
of the lot shall be selected at random from each production lot of valves per valve type, pressure class and nominal size,
and tested according ISO 15848 Part 2.
A.9.3.6.2. The manufacturer shall prepare specific Factory Acceptance Test (FAT) procedure, according ISO 15848 Part
2, and submit for PETROBRAS approval.
A.9.3.6.3. The “Tightness Class” shall be according:
Table A.62 – Tightness class for stem seals - fugitive emissions (ref.: ISO 15848 Part 1)
Tightness Class
Measured Leak Rate 1
(Stem seals)
A ≤ 50
B ≤ 100
C ≤ 1000
1
Expressed in ppmv measured with the sniffing method as defined in
ISO 15848 Part 1 - Annex B (1 ppmv = 1 ml/m3 = 1 cm3/m3)
Table A.63 – Tightness class for body seals - fugitive emissions (ref.: ISO 15848 Part 1)
Measured concentration
≤ 50 1
(Body seals)
1
Expressed in ppmv measured with the sniffing method as defined in
ISO 15848 Part 1 - Annex B (1 ppmv = 1 ml/m3 = 1 cm3/m3)
A.9.3.6.4. The FAT report shall be according item 7 of ISO 15848 Part 1.
A.9.3.7.1. All HIPPS valves shall be able to pass through a regular testing to demonstrate correct function and monitoring
operating status. The test interval shall be consistent with the basis of the SIL analysis.
A.9.3.7.2. Following are the minimum considerations that shall be verified during in place test of a HIPPS valve:
- Rev. 11 - Page 68 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
a) Regular Pressure/Leak Integrity Testing: The HIPPS shall be capable of demonstrating that the system has
sufficient integrity to contain SIP with leakage less than the maximum leak rate. Testing interval will be
determined by SIL rating or regulatory requirement.
b) Maximum Leak Rate Testing: The HIPPS design shall include appropriate methods to measure or infer the leak
rate of the HIPPS for comparison to the predetermined maximum leak rate. Maximum leak rate determination
shall consider both short-term shutdown events and long-term shutdown events such as a storm shut-in and
shall either be set by the operator or by regulatory requirement.
c) Partial Stroke Testing (PST): Each valve shall be supplied with a dedicated Partial Stroke Test (PST) system
installed inside the local control valve cabinet. Required Partial Stroke Test shall be implemented using devices
specifically designed and certified for that purpose. PST shall be considered as a functional test which covers
only a fraction of the possible failures, and not as self-test with diagnostic coverage. The fraction detected shall
be properly documented. As minimum, the following tests shall be scope of the PST:
- 4 actuations of HIPPS valves under operational condition, with nominal line pressure in upstream, downstream
and body cavity;
- 4 actuations of HIPPS valves under DBB condition, direction open to close. In this case the valve should be at
opened position, with nominal line pressure in the bore and without pressure in the cavity;
- 4 actuations of HIPPS valves under DBB condition, direction close to open. In this case the valve should be at
closed position, with nominal line pressure in upstream and downstream, and without pressure in the cavity;
- For the FAT tests of the valve HIPPS, the sequence described herein shall be done considering the line pressure
of 0% PMT, 50% PMT and 100% PMT.
NOTE: The results of the PST shall be registered using a statistical analysis (i.e.: average, standard deviation), in order
to serve as a reference for the commissioning test and periodical test. Also, a failure mode effects and criticality analysis
(e.g.: FMECA) shall be considered to be used.
A.10.1. The manufacturer shall present a tested/validated procedure by laboratory performance for the preservation
system and a procedure with handling, storing, packaging and shipping the valve (including actuator and positioner -
electric/electronic parts).
A.10.2. After hydrostatic test, all valves shall be purged with dry compressed air, in the fully open position, until they are
completely dry.
A.10.3. After purge, the valve shall be kept closed or opened, according to manufacturer instruction, inner protected with
VCI for all the parts and no corrosion protector that will need any solvent to be removed may be used.
A.10.4. Valves with corrosion resistant materials needs the corrosion inhibitor for liquid and vapor phase added on the
water, but do not need the use of VCI. Corrosion protector that will need any solvent to be removed shall not be used.
A.10.5. Valves made of brass, stainless steel and other non-oxidizable metal alloys shall receive protection against dust
and moisture.
A.10.6. Small sized valves may be shipped inside a collective package. Even that, each valve shall be individually
package prior to assembly the collective package.
- Rev. 11 - Page 69 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
A.11. DOCUMENTATION
A.11.1. DOCUMENTATION FORMATS & QUALITY
A.11.1.1. Whenever is possible (e.g.: a supply from a Brazilian manufacturer) all documentation shall be delivered in
Portuguese (pt-BR). An alternative language to be considered for the documentation shall be English (e.g.: supply from
an international manufacturer). Any deviation shall be requested and approved by PETROBRAS in advance of the
delivery.
A.11.1.2. Typically, the format for the documents shall be Adobe Acrobat PDF (*.PDF). Other formats shall be agreed
with PETROBRAS.
A.11.1.3. All documentation shall be of good quality with maximum legibility. Scanned images shall be checked before
submittal for proper image quality, skewness and completeness.
A.11.2.1. The Data Book shall be filled in a manner which will facilitate rapid retrieval of information. They shall be made
available to PETROBRAS, if required, for at least 5 years following the commencement of the guarantee period of last
batch commercialized.
A.11.2.2. The Data Book shall represent the manufacturer's compilation of calculations together with the necessary
drawings, manufacturing, testing and inspection procedures, certificates, personnel qualifications, non-conformance
reports, records and reports required to demonstrate that the valve and actuator is in compliance with PETROBRAS’s
requirements.
A.11.2.3. It shall include, as minimum:
f) NDT reports with lists of welder and NDT operator qualifications and procedures, and drawings of critical areas
for NDT;
j) Actuator certificate;
- Rev. 11 - Page 70 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
k) Positioner certificate;
A.11.2.4. The issue of certificates shall be according EN 10204 type 2.2 for parts with no risk for environment as: hard
welding deposit, closures, seal, springs and so on.
A.11.2.5. The issue of certificates shall be according EN 10204 type 3.1 for parts with risk for environment as: body,
bonnet, cover, stem, studs/bolts, etc.
A.11.2.6. The Data Book shall be issued one per valve or one per purchase order (with traceability for valves groups).
One hard copy of the Data Book shall be sent with the valve to final destination and an electronic copy shall be sent to
the PURCHASER.
A.11.2.7. All material certificates shall be identified with: valve serial number, project name (when applicable), purchase
order number, order item number, VDS number or project number.
A.11.3.1. The User Manual shall in an organized manner, give sufficient information in order to enable operation and
maintenance of the valve in a safe, economical and functionally correct manner during all phases after installation.
A.11.3.2. The User Manual shall cover valve and actuator.
A.11.3.3. All documents shall be updated to "as-built".
A.11.4.1. The manufacturer shall prepare and submit procedure(s) for PETROBRAS approval, showing the following:
a) description of the initial preservation/protection/packing carried out by the manufacturer prior to shipment:
- The procedure shall also specify type of preservatives/ lubricants used, with technical data, handling and safety
instructions, especially giving details of any chemical substances used that may be hazardous to personnel or
environment.
- Preservation maintenance is to be carried out by the user during storage, installation and in the period prior to
start-up for the intended use.
- The procedure shall indicate the proposed lifting methods for the valve and actuator, and all additional measures
that shall be observed prior to and during installation.
A.11.4.2. The documentation of preservation, protection and packing shall fulfill all requirements stated on item A.10.
- Rev. 11 - Page 71 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
A.11.5.1.1. All valves specified for application in Exploration and Production (E&P) oil production and process facilities
have a unique code, in order to have uniformity and to systematize the coding of valves so that they can be handled in
an organized manner and information can be easily retrieved.
A.11.5.1.2. The complete structure of all valve codes shall be as follows:
A.11.5.2.1. The valve code shall be made up of 2 basic groups ordered as follows:
Where:
L is a letter;
A, B are numbers.
This is the basic group that identifies the type of the valve.
This group is comprised of three letters and its configuration is illustrated as follows:
Group 0
Valve Type
LLL
The following characters shall be used to distinguish the type of the valve:
VAG – Needle valve
- Rev. 11 - Page 72 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
This is the basic group that identifies the pressure rating of the valve.
This group is comprised at least of three and maximum of 5 numbers and its configuration is illustrated as
follows:
Group 1
Pressure Rating
The following characters shall be used to distinguish the pressure rating of the valve:
125 – ASME Class 125
801 – ASME Class 800 with SCH 40S (for ball valves)
801 – ASME Class 800 with SW ends ASME B16.11 (for gate valves)
1501 – ASME Class 1500 with SCH 40S (for ball vales)
1501 – ASME Class 1500 with SW ends ASME B16.11 (for gate valves)
2501 – ASME Class 2500 with SCH 40S (for ball valves)
2501 – ASME Class 2500 with SW ends ASME B16.11 (for gate valves)
- Rev. 11 - Page 73 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
This is the basic group that identifies the VSL of the valve.
This group is comprised with one number and its configuration is illustrated as follows:
Group 2
VSL
The following characters shall be used to distinguish the VSL of the valve:
1 – VSL-1
2 – VSL-2
3 – VSL-3
4 – VSL-4
A.11.5.4.1. The valve code shall be made up of 4 specific groups ordered as follows:
Where:
L is a letter;
C, D, E are numbers.
This is the basic group that identifies the material class of the valve.
This group is comprised of one letter and its configuration is illustrated as follows:
Group 3
Material Class
- Rev. 11 - Page 74 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
The following characters shall be used to distinguish the material class of the valve:
C – Carbon steel
A – Alloy Steel
S – Stainless steel
D – Duplex steel
N – Nickel alloy
U – Uncommon materials
This is the basic group that identifies the body material of the valve.
This group is comprised of one number and its configuration is illustrated as follows:
Group 4
Body Material
C
The following characters shall be used to distinguish the body material of the valve, related to the specific
material class of the valve:
Table A.64 – Identification of body material code, according respective material class
- Rev. 11 - Page 75 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
Table A.64 – Identification of body material code, according respective material class
Material Class
Body C A S D N U
Material
Stainless Nickel Uncommon
Carbon steel Alloy steel Duplex steel
steel alloys materials
ASTM A182
ASTM A105 ASTM A350 LF3 Gr. F304 Inconel 625
1 or or or ASTM A995 Gr. 1B (UNS Bronze
ASTM A216 WCB ASTM 352 LC3 ASTM A351 N06625)
Gr. CF8
ASTM A182
ASTM A182 Gr.
A350 LF2 CL1 Gr. F316
F51
2 or ASTM A182 F5 or
or
- ASTM A536-65-45-12
ASTM A352 LCB ASTM A351
ASTM A995 Gr. 4A
Gr. CF8M
ASTM A105
or ASTM A182
Gr. F317 ASTM A182 Gr.
ASTM A216 WCB ASTM A182 F11 ASTM B148
3 + CL2
or F55 or -
(UNS C95800)
ASTM A351 ASTM A995 Gr 6A
Organic Coating Gr. CG8M
(Onshore use only)
ASTM A105
or ASTM A182
Gr. F347
ASTM A216 WCB
4 +
ASTM A522 Type I or - - Plastics
ASTM A351
Organic Coating Gr. CF8C
(Offshore)
ASTM A105 ASTM A350 LF3
or or
ASTM A216 WCB ASTM A352 LC3
5 + +
- - - Gray Iron
This is the basic group that identifies the obturator type of the valve.
This group is comprised of one number and its configuration is illustrated as follows:
Group 5
Obturator Type
D
The following characters shall be used to distinguish the obturator type of the valve:
- Rev. 11 - Page 76 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
Valve Type
Obturator
type Butterfly
Gate valve Globe valve Check Valve
valve
Solid Category A
0 Bevelled disc Piston
wedge (concentric)
Category B
1 Slab gate Angular Dual Plate Double offset
(bi-eccentric)
Category B
Expanding
2 - Swing Triple offset
gate
(tri-eccentric)
3 - - Axial non-slam -
4 - - Ball -
NOTE: For ball valves, the last two digits “D” and “E” in the valve code presents the configuration number of the valve,
where:
DE – presents the basic configuration, according Table A.25 – for ball valves up to NPS 1 1/2 (“Forged” valves).
D - presents the selected group seal, according Table A.23 – for ball valves with NPS 2 and above;
E - presents the basic configuration, according Table A.26 – for ball valves with NPS 2 and above;
This is the basic group that identifies the TRIM design of the valve.
This group is comprised of one number and its configuration is illustrated as follows:
Group 6
TRIM Design
E
The following characters shall be used to distinguish the TRIM design of the valve:
Valve Type
TRIM Valve Type
design Gate Butterfly
Check Butterfly Category A (Concentric)
Globe Category B
TRIM Double Flanged
Standard Soft Lug Wafer
1 Wafer Config. (Short Pattern)
TRIM TRIM
Alternative Metal x Metal #1 1 2 3
2 Lug
TRIM TRIM
#2 4 5 6
Alternative
Double Flanged
3 N/A Metal x Metal #3 7 8 9
(Short Pattern)
TRIM
NOTE: For ball valves, the last two digits “D” and “E” in the valve code presents the configuration number of the valve,
where:
- Rev. 11 - Page 77 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
DE – presents the basic configuration, according Table A.25 – for ball valves up to NPS 1 1/2 (“Forged” valves).
E - presents the basic configuration, according Table A.26 – for ball valves with NPS 2 and above;
Example 1
Gate valve, pressure rating class 900, VSL-2, material class of carbon steel, solid wedge, using standard TRIM:
VGA-900-2-C101
Valve Type: VGA – Gate valve
Pressure Rating: 900 – Class 900
VSL: 2 – VSL-2
Material Class: C – Carbon steel
Body Material: 1 – ASTM A105 or ASTM A216 WCB
Obturator type: 0 – Solid wedge
Trim design: 1 – Standard TRIM
Example 2
Ball valve, pressure rating 1500, VSL-2, material class of carbon steel, configuration 04 with nipple SCH XXS:
VES-1504-2-C207
Valve Type: VES – Ball valve
Pressure Rating: 1504 – ASME Class 1500 with SCH XXS
VSL: 2 – VSL-2
Material Class: C – Carbon steel
Body Material: 2 – A350 LF2 CL1 or ASTM A352 LCB
Configuration: 07 – Metal to metal ball valve with configuration according Table A.25
Example 3
Ball valve, pressure rating 2500, VSL-3, material class of super duplex, soft sealing, fire tested, DIB-2:
VES-2500-3-D339
Valve Type: VES – Ball valve
Pressure Rating: 2500 – ASME Class 2500
VSL: 3 – VSL-3
Material Class: D – Super duplex
Body Material: 3 – ASTM 182 Gr. F55
Seal Group: 3 – Groups D or E
Configuration: 9 – Soft sealing ball valve with configuration according Table A.26.
- Rev. 11 - Page 78 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
DISCIPLINE: PIPING
Piping Materials Specification for E&P Production Facilities
- Rev. 11 - Page 79 of 79
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
Discipline: Piping
PIPING MATERIALS SPECIFICATION FOR E&P PRODUCTION FACILITIES
A.12.2 BALL VALVES
Valve Code VES-10000-2-D334 VES-1500-1-C100 VES-1500-1-C114 VES-1500-1-C134
Specs J10 J12P J12 G4 G10P G10 G10P G10
1. Valve Type Ball Ball Ball Ball
2. Sealing Type Soft Soft Soft Soft
3. Valve Specification Level (VSL) VSL-2 VSL-1 VSL-1 VSL-1
4. Ball Mouting Trunnion Trunnion Trunnion Trunnion
5. Standard API 6A API 6D API 6D / IOGP S-562 API 6D / IOGP S-562
6. Size Range (NPS) 1" - 2" N/A 2" - 24" 2" - 24"
7. End Connection API 6A, 6BX N/A ASME B16.5, RTJ ASME B16.5, RTJ
8. Pressure Class max. press 10000 psi 1500 1500 1500
9. Temperature -50°C to 150°C 0°C to 100°C 0°C to 150°C 0°C to 150°C
10. Material Class Duplex Steel Carbon Steel Carbon Steel Carbon Steel
11. Body Material ASTM A182 Gr F55 ASTM A105 ASTM A105 + SS316 weld overlay (acc. item ASTM A105 + SS316 weld overlay (acc. item
A.7.1.7.3) A.7.1.7.3)
12. Obturator Material Super Duplex (UNS S32760) AISI 410 AISI 410 AISI 410
13. Seat Material Super Duplex (UNS S32760) AISI 410 AISI 410 AISI 410
14. Seat Insert PEEK PEEK PEEK PEEK
15. Spring (Seat) Material UNS N07750 UNS N07750 UNS N07750 UNS N07750
16. Stem Material ASTM A276 (UNS S32760) ASTM A276 (UNS S41000) ASTM A276 (UNS S41000) ASTM A276 (UNS S41000)
17. Seat-Stem Seal Group E (acc. item A.7.1.5.6) Group A (acc. item A.7.1.5.6) Group B (acc. item A.7.1.5.6) Group D (acc. item A.7.1.5.6)
18. Operator Type Gearbox Lever Gearbox Gearbox
19. Additional Requirement N/A N/A N/A N/A
20. Seat Type Side A: SPE / Side B: SPE; DBB N/A Side A: SPE / Side B: SPE; DBB Side A: SPE / Side B: SPE; DBB
21. Bore Type Full Bore Full Bore Full Bore Full Bore
22. Body Construction split body, bolted split body, bolted split body, bolted split body, bolted
23. Cladding or Coating N/A N/A Partial clad - SS316 weld overlay on all body Partial clad - SS316 weld overlay on all body
sealing areas sealing areas
24. Valve Testing FAT according A.9.3 FAT according A.9.3 FAT according A.9.3 FAT according A.9.3
25. Notes N/A N/A N/A N/A