MICROWAVE OVEN

MODEL: AG930AZJ-P00C (9 00W 220V50Hz)

SERVICE MANUAL
CAUTION
BEFORE SERVICING THE UNIT，READTHE SAFETY PRECAUTIONS IN THIS
MANUAL
 SAFETY PRECAUTIONS
This device is to be serviced only by properly qualified service personnel.
Consult the service manual for proper service procedures to assure continued safety operation and for precautions to
be taken to avoid possible exposure to excessive microwave energy.

PRECAUTIONS TO BE OBSERVED BEFORE AND

DURING SERVICING TO AVOID POSSIBLE
EXPOSURE TO EXCESSIVE MICROWAVE ENERGY
A) Do not operate or allow the oven to be operated with the door open.
B) Make the following safety checks on all ovens to be serviced before activating the magnetron or other
microwave source, and make repairs as necessary; (1) interlock operation, (2) proper door closing, (3)
seal and sealing surfaces (arcing, wear, and other damage), (4) damage to or loosening of hinges and
latches, (5) evidence of dropping or abuse.
C) Before turning on microwave power for any service test or inspection within the microwave generating
compartments, check the magnetron, wave guide or transmission line, and cavity for proper alignment,
integrity, and connections.
D) Any defective or misadjusted components in the interlock, monitor, door seal, and microwave generation
and transmission systems shall be repaired, replaced, or adjusted by procedures described in this manual
before the oven is released to the owner.
E) A microwave leakage check should be performed on each oven prior to release to the owner.

CAUTION
MICROWAVE RADIATION
DO NOT BECOME EXPOSED TO RADIATION FROM THE MICROWAVE GENERATOR
OR OTHER PARTS CONDUCTING MICROWAVE ENERGY.
 TABLE OF CONTENTS

（page）
SAFETY PRECAUTIONS---------------------------------------------------------Inside front cover
CAUTIONS------------------------------------------------------------------------------------------------1-1
THE HEATING PRINCIPLE OF MICROWAVE--------------------------------------------------2-1
INSTALLATIONS----------------------------------------------------------------------------------------3-1
OPERATING INSTRUCTIONS----------------------------------------------------------------------4-1
SCHEMATIC DIAGRAM--------------------------------------------------------------------------4-1
CIRCUIT DESCRIPTION-------------------------------------------------------------------------4-2
SERVICE INFORMATION-----------------------------------------------------------------------------5-1
TOOLS AND MEASURING INSTRUMENTS------------------------------------------------5-1
MICROWAVE LEAKAGE TEST----------------------------------------------------------------5-2
MEASUREMENT OF MICROWAVE POWER OUTPUT---------------------------------5-3
TROUBLE SHOOTING PROCEDURES------------------------------------------------------5-4
COMMON BREAKDOWN AND MEANS OF REPAIRING-------------------------------5-8
IMPORTANT THINGS TO DO PRIOR TO CRITICAL PART SERVICING-------------------------5-9
SAFETY CHECKS AND TESTS AFTER SERVING--------------------------------------5-10
EXPLODED VIEW---------------------------------------------------------------------------------------6-1
REPLACEMENT PARTS LIST-----------------------------------------------------------------------6-1
 CAUTIONS
Unlike other appliances, the microwave oven
is
MICROWAVE RADIATION
high-voltage and high-current equipment. Personnel should not be exposed to the
Though it is free from danger in ordinary use, microwave energy which may radiate from the
extreme care should be taken during repair. magnetron or other microwave generating
device if it is improperly used or connection.
• DO NOT operate on a 2-wire extension cord during All input and output microwave connections,
repair and use. waveguide, flange and gasket must be secure
• NEVER TOUCH any oven components or wiring during never operate the device without a microwave
operation. energy absorbing load attached.
• BEFORE TOUCHING any parts of the oven, always Never look into an open waveguide or antenna
remove the power plug from the outlet. while the device is energized.
• For about 30 seconds after the oven stops, an electric
charge remains in the high voltage capacitor. When
replacing or checking, you must discharge the high
• Proper operation of the microwave oven
voltage capacitor by shorting across the two terminals
requires that
with an insulated screwdriver.
the magnetron be assembled to the waveguide
and
cavity. Never operate the magnetron unless it is
properly installed.
• Be sure that the magnetron gasket is
properly
installed around the dome of the tube
whenever
installing the magnetron.

• Remove your watches whenever working close to or

replacing the Magnetron.
• DO NOT touch any parts of the control panel circuit. A
resulting static electric discharge may damage this
P.C.B.
• NEVER operate the oven with no load.
• NEVER injure the door seal and front plate of the oven
cavity.
• NEVER put iron tools on the magnetron.
• NEVER put anything into the latch hole and the
interlock switches area.` THE OVEN IS TO BE SERVICED
ONLY
BY PROPERLY QUALIFIED SERVICE
PERSONNEL.

1-1
 THE HEATING PRINCIPLE OF MICROWAVE
Microwave is one kind of radio wave whose wave length is very short, frequency is very high. Therefore, it is called ultrahigh
frequency electromagnetic wave. Microwave can heat food mainly result in the mutual affect of the food in the microwave field and
microwave field itself.
Under the affect of microwave field, the thermal effect mechanism produced from the mutual affect of the microwave and the food
includes two aspects: One is Dielectric loss of polar molecule, the other is conductive loss of ion.
Usually, food is constitute of organism (plant and animal).The organism is formed by all kinds of polar water molecule, polar
protein molecule, and all sorts of salt ion. The center of gravity of the positive and negative charge in the molecule is not coincide.
In normal condition, the molecule is in irregular order due to its thermal action, thus the food do not appear polarity (FIG.1-
1a).Under the action of outer electric field, the positive end of the polar molecule trend to the negative electric field, the negative
end of polar molecule trend to the positive electric field, and somewhat arrange in order through the direction of the electric
field(FIG.1-1c).This phenomenon usually be called “TORQUE POLARITY”. When the outer electric field apply for the opposite
polarity, the polar molecule then arrange an opposite direction order accordingly (FIG.1-1b).If the direction of the outer electric field
changed repeatedly, the polar molecule would repeatedly sway accordingly. During the swaying, it understands that the polar
molecule would produce heat due to somewhat similar friction among them.

When the electric field is applied for ultrahigh frequent microwave field from the outside, its direction would change tens billion
times per second, so do the molecule. This kind of molecule swaying producing similar frictional heat from the interference and
block of the action strength among the molecule, and changed to microscopic microwave heating. Microwave heating not only
concerned the nature of the matter itself, but also closely connected with the electric field strength and frequency. When the
frequency is low, the molecule swaying rate and the acute degree of the mutual friction among the molecule is low, and would
produce much heat. When the frequency is too high, as the swing of the polar molecule is with rotating inertia, it made the swing
do not in line with the changing rhythm of the electric field because of the friction drag, thus, actually lowed the polar molecule
swaying speed. The friction dragging degree is concerning about the magneto electric wave frequency, polar molecule shape, and
the matter’s sticky degree. To different matter’s molecule, there are different special frequency zone. Those ado absorb microwave
energy from these zone are most capable to turn microwave energy to heat energy.
Apart from the above said action, there is another action which is electric ion under the action of microwave field, act fiercely
accompanied with the acceleration of electric field. The positive ion transfer to the negative polarity of the field while the negative
ion do opposite. Accompanying with the changing electric field, the electric ion changing accordingly. During the transferring, heat
produced with the crash among the ion. This kind of action take the main effect to those microwave heating of high salt molecule.
No matter it is the polar molecule swaying or the ion transferring, they both are turning the microwave energy which the heating
matter got from the microwave field to hear energy. From the analysis of theory, we can draw such a conclusion that the power
which a unit of volume matter absorbed from the microwave field as the following formula:
Pa=K·E· F·Er·tgδ
Pa Stands for the power the heated matter absorbed from the microwave field.
K Stands for a constant
E Stand for microwave field strength
F Stands for the microwave frequency.
Er Stands for relative dielectric constant of the heated matter.
tgδStands for loss angle tangent of the heated matter
2-1
 INSTALLATIONS
BEFORE YOU BEGIN, READ THE FOLLOWING INSTRUCTIONS COMPLETELY

INSTALLING
EARTHING INSTRUCTIONS
1. Empty the microwave oven and clean inside it with
a soft, damp cloth. Check for damage such as This microwave oven is designed to be used in a fully

misaligned door, damage around the door or dents earthed condition.

inside the cavity or on the exterior. It is imperative, therefore, to make sure it is properly
earthed before servicing

2. Put the oven on a counter, table, or shelf that is WARNING-

strong enough to hold the oven and the food and
utensils you put in it. (The control panel side of the THIS APPLIANCE
oven is the heavy side. Use care when handling.)

MUST BE EARTHED
3. Do not block the vent and the air intake openings.
Blocking vent or air intake openings can cause IMPORTANT
damage to the oven and poor cooking results.
Make sure the microwave oven legs are in place to The wires in this mains lead are colored in
ensure proper air flow. accordance with the following code:
Green-and-yellow: Earth
4. The oven should not be installed in any area where Blue: Neutral
heat and steam are generated, because they may Brown: Live
damage the electronic or mechanical parts of the
unit. As the colors of the wires in the mains lead of this

Do not install the oven next to a conventional appliance may not correspond with the colored

surface unit or above a conventional wall oven. markings identifying the terminals in your plug,
proceed as follows.

5. Use microwave oven in an ambient temperature

less than 104°F(40°C). The wire which is colored green-and-yellow must be
connected to the terminal in the plug which is marked

6. Place the microwave oven on a sturdy and flat

with the letter E or by the earth symbol ( ) or
surface at least 10 cm(4 inches) from the wall.
colored green or green-and-yellow.

7. Place the microwave oven as far away as possible

from TV, RADIO, COMPUTER, etc., to prevent The wire which is colored blue must be connected to

interference. the terminal in the plug which is marked with the letter
N or colored black.

The wire which is colored brown must be connected

to the terminal in the plug which is marked with the
letter L or colored red.

3-1
SCHEMATIC DIAGRAM
CIRCUIT DESCRIPTION
GENERAL DETAILS power of microwave oven as POWER LEVEL.
• The low voltage transformer supplies the necessary
voltage to the micom controller when power cord is WHEN THE DOOR IS OPENED DURING
plugged in. COOKING
• When the door is closed, the primary switch is ON, the • Both the primary switch and relay 2 are cut off primary
secondary switch is ON, and the monitor switch opens winding voltage of the high voltage transformer.
(contact COM and NO). • ON-OFF of relay 2 is coupled electrically with opening
and closing of the secondary switch.
WHEN SELECTING COOKING POWER • When the door is opened, the secondary switch is
LEVEL AND TIME opened and when the door is closed, the secondary
• The micom controller memorizes the function you set. switch is closed.
• The time you set appears in the display window. • The cooking time stops counting down.
• Each indicator light turns on to indicate that the stage • Relay stops functioning.
has been set. • As the door is opened, if the contact of primary switch
and relay 2 and/or secondary switch fails to open, the
WHEN TOUCHING THE START PAD fuse opens due to the large current surge caused by
• The coil of the relay is energized by the micom the monitor switch activation, which in turn stops
controller. magnetron oscillation.
• Power input is supplied to the high voltage transformer PRIMARY
FUSE SWITCH
through the fuse to the primary switch and relay 2.
• Turntable rotates.
FUSE PRIMARY L
SWITCH
MONITOR TRANS-
SWITCH FORMER
L N
MONITOR TRANS-
SWITCH FORMER
N RELAY 2 SECONDARY
SWITCH
MICOM CONTROLLER
RELAY 2 SECONDARY
SWITCH
MICOM CONTROLLER
WHEN TOUCHING THE START KEY
WITH THE GRILL COOKING FUNCTION
• The fan motor rotates and cools the magnetron by
blowing the air (coming from the intake on the
SELECTED
baseplate) • The contacts of the primary switch and the secondary
• The air is also directed into the oven to exhaust the switch close the circuit.
vapor in the oven through the upper plate. • A.C.voltage is applied to the grill heater through grill
• Cooking time starts counting down. thermostat as shown by the solid line.
• 3.2 volts AC is generated from the filament winding of
GRILL
the high voltage transformer. This 3.2 volts is applied THERMOSTAT
to the magnetron to heat the magnetron filament
through two noise preventing choke coils. TOP HEATER RELAY
• A high voltage of approximately 2100 volts AC is L
L
generated in the secondary of the high voltage G -Y
E GRILL
N HEATER
transformer which is increased by the action of the high N
voltage diode and charging of the high voltage
capacitor.
• The negative 4,000 Volts DC is applied to the filament
of the magnetron.
• Turntable rotates.
WHEN THE OVEN IS SET AT ANY LEVEL • The fan motor rotates.
EXCEPT MAXIMUM. • The air is also directed into the oven to exhaust the
• The micom controller controls the ON-OFF time of relay vapor in the oven through the base plate and upper
2 by the applied signal to vary the average output plate.

4-2
 SERVICE INFORMATION
TOOLS AND MEASURING INSTRUMENTS
NECESSARY TOOLS NECESSARY MEASURING
Tools normally used for TV servicing are sufficient. INSTRUMENTS
Standard tools are listed below. • TESTER(VOLTS-DC, AC., Ohmmeter)
• Diagonal pliers • Microwave survey meter
• Long nose pliers - Holaday HI-1710(A)
• Phillips screwdriver - Narda 8100
• Flat blade screwdriver 8200
• Wrench (size 5mm) • Inch scale
• Nutdriver (size 5mm) • 600 cc non conductive material beaker (glass or
• Adjustable wrench plastic), inside diameter: approx. 8.5 cm(31/2 in.)
• Soldering iron • Cylindrical and made of borosilicate glass vessel.
• Solder max. thickness: 3 mm
• Vinyl insulation tape outside diameter: approx. 190mm
• Polishing cloth height: approx. 90mm
• Glass thermometer: 100°C or 212°F (1 deg scale)

MICROWAVE LEAKAGE TEST

CAUTIONS MEASURING MICROWAVE ENERGY
• Be sure to check microwave leakage prior to LEAKAGE
servicing the oven if the oven is operative prior to • Pour 275±15 cc of 20±5°C(68±9°F) water in a
servicing. beaker
• The service personnel should inform the which is graduated to 600 cc, and place the beaker
manufacture importer, or assembler of any certified on the center of the turntable.
oven unit found to have a microwave emission • Set the energy leakage monitor to 2,450 MHz and
2
level in excess of 5 mW/cm and should repair any use it following the manufacturer's recommended
unit found to have excessive emission levels at no cost test procedure to assure correct result.
to the owner and should ascertain the cause of the • When measuring the leakage, always use the 2-
excessive leakage. The service personnel should inch (5 cm) spacer supplied with the probe.
instruct the owner not to use the unit until the oven has • Operate the oven at its maximum output.
been brought into compliance. • Measure the microwave radiation using and
• If the oven operates with the door open, the service electromagnetic radiation monitor by holding the
personnel should: probe perpendicular to the surface being measured
- Tell the user not to operate the oven. Move probe along shaded area
- Contact the manufacturer. Probe scanning speed: Less than 2.5 cm/sec
• The service personnel should check all surface and
vent openings for microwave leakage.
• Check for microwave leakage after every servicing. The
power density of the microwave radiation leakage
emitted by the microwave oven should not exceed
5 mW/cm2. Always start measuring of an unknown field
to assure safety for operating personnel from radiation
leakage.

5-1
MEASUREMENT WITH OUTER CASE NOTES WHEN MEASURING
REMOVED • Do not exceed meter full scale deflection.
• When you replace the magnetron, measure for • The test probe must be removed no faster than
microwave energy leakage before the outer case is 1 inch/sec (2.5 cm/sec) along the shaded area,
installed and after all necessary components are otherwise a false reading may result.
replaced or adjusted. • The test probe must be held with the grip portion of
Special care should be taken in measuring the the
following parts. handle.
- Around the magnetron A false reading may result if the operator's hand is
- The waveguide between the handle and the probe.
• When testing near a corner of the door, keep the
WARNING : AVOID CONTACTING ANY probe
HIGH VOLTAGE PARTS perpendicular to the surface making sure the probe
(Magnetron, H.V. Transformer, horizontally along the oven surface, this may possibly
H.V. Capacitor, H.V. Cable Ass’y, cause probe damage.
H.V. Fuse) RECORD KEEPING AND NOTIFICATION
AFTER MEASUREMENT
• After adjustment and repair of any microwave energy
MEASUREMENT WITH A FULLY interruption or microwave energy blocking device,
ASSEMBLED OVEN record the measured values for future reference. Also
• After all components, including the outer case, are fully enter the information on the service invoice.
assembled, measure for microwave energy leakage • The microwave energy leakage should not be more
around the door viewing window, the exhaust opening, than 1.0 mW/cm2. after determining that all parts are in
and air inlet openings. good condition, functioning properly and genuine
• Microwave energy leakage must not exceed the values replacement parts which are listed in this manual have
prescribed below. been used.
NOTE: Leakage with the outer case removed less than • At least once a year, have the electromagnetic energy
3 mW/cm2. Leakage for a fully assembled leakage monitor checked for calibration by its
oven (Before the latch switch (primary) is
interrupted) with the door in a slightly opened
position-less than 1 mW/cm2

5-2
 MEASUREMENT OF MICROWAVE POWER OUTPUT

• Microwave power output measurement is made with • The microwave power output P in watts is
the microwave oven supplied at its rated voltage and calculated
operated at its maximum microwave power setting with approximately from the following formula :
a load of (1000±5) g of potable water. P=4187 x (△T)/T
• The water is contained in a cylindrical borosilicate glass is measured while the microwave generator is
vessel having a maximum material thickness of 3 mm operating at full power. Magnetron filament heat-up
and an outside diameter of approximately 190mm. time is not included. (about 3 sec)
• The oven and the empty vessel are at ambient • The water is stirred to equalize temperature
temperature prior to the start of the test. throughout
• The initial temperature (T1) of the water is (10±2)°C It the vessel, prior to measuring the final water
is measured immediately before the water is added to temperature.
the vessel. After addition of the water to the vessel, • Stirring devices and measuring instruments are
the load is immediately placed on the center of the selected in order to minimize addition or removal of
turntable which is in the lowest position and the heat.
microwave power switched on.
• The time T for the temperature of the water to rise by a
value . T of (10±2)°K is measured, where T is the time
in seconds and .T is the temperature rise. The initial
and final water temperatures are selected so that the
maximum difference between the final water
temperature and the ambient temperature is 2°K.

5-3
 TROUBLE SHOOTING PROCEDURES
Before overhauling a microwave oven, you should judge the breakdown and the cause correctly, then you can repair it with
corresponding ways. The overhauling must be proceed in order, any hasty conclusion is not recommendable, otherwise
overworking would be done when repair. The microwave oven may occur compound breakdown due to all kinds of different
reasons, thus, when overhaul, they all should be taken into consideration. Special attention must be given to the microwave
leakage and the electric insulation when examine because they may do harmful to the repairing staff.
Ⅰ.MEANS OF THE BREAKDOWN EXAMINING
How to examine a microwave oven with breakdown? A better means which demonstrated in practical operating are through
inspecting and listening. On the basis of large amounts of perceptual knowledge, you can judge and analysis the breakdown
quickly and correctly.
1. Inspection.
Inspect whether the oven shape is disordered and where is the disordered position, if any. It is normal if the outer case
disordered a little, but abnormal if the oven, the door disordered, the door hook broken, the door crooked, or there are too
much looseness between the door and the oven after the door is closed.
2. Listening.
Listening to the voice of the oven operating and the noise of the fan after it conducted. Minor “wen wen” noise, cycling “kala”
noise and “shishi” noise should be consider as normal. But it is abnormal if the following noise occurred:
(1) Sound “wenwen” noise.
(2) Long time “shishi” noise.
(3) Strike voice like “pipa pipa”.
Ⅱ.SPOT EXAMINING STEPS OF THE MICROWAVE OVEN.
1. Examine the microwave insulating resistance.
Measure the insulating resistance with a multi meter or a mega ohmmeter. The value should not less than 2 mega ohm.
Otherwise, part examination should be taken at once. Such as checking whether the motor, the thermal cutout, the
transformer or the capacitor are electricity leaking.
2. Examination of the resistance value of the microwave oven.
Close the door, set the time (the oven is at operating condition but the power plug haven’t been plugged in), measure the two
feet(L-N)of the power plug with Rx1 grade of a multimeter, the resistance value should be about 22 ohm.
If open circuit occurred, then you must check whether the 10 A fuse is broken、the primary winding of the transformer is open
circuit、the thermal cutout is open circuit or not, you must check whether the interlock device is put through or all the plugs
are connected well. If short circuit occurred, you should check whether the primary winding of the power transformer is short-
circuited or part short-circuited.
3. Examination of microwave leakage
Measure the microwave leakage with a microwave leakage Measure. Place a graduate of 275ml water at the middle of the
glass tray of the oven (FIG.5-1). Close the door, power set high, time set to 3 minutes, press the starting button to operate the
oven. After rectified the microwave leakage measure, measure around the door crack, those hole position of the window and
the air vent at four sides of the oven with the probe of the measure. When measure, the moving speed of the probe should
not exceed 2.5cm per second, and the measuring direction should be the same with the outing direction of the microwave
leakage (FIG.5-2).
2
When measuring, the ultimate value of microwave leakage of all the measured position should not exceed 1.0 mili watt/cm ,
or should be considered as abnormal.

275ml

Glass tray

FIG.5-1 FIG.5-2

5-4
4. Examine when the oven at operating, but the food can’t be heated
Pull out the power plug, take off the outer case, discharge the capacitor, measure the resistance value of the primary winding and
the secondary winding of the transformer with a multi meter (FIG.5-3 and FIG.5-4). The resistance value of the primary winding
should be about 2.2 ohm, the secondary winding should be about 130 ohm, otherwise, it indicates the transformer has broken,
and should be replaced by a new one.
If the transformer is normal, then the high voltage capacitor should be checked. Pull out the connecting plug of the capacitor,
and measure it with Rx1 grade of a multi meter, the two rod of the multi meter connect the two polarity of the capacitor. When
they just connected, the reading of the multi meter should be zero, then enlarge to nine mega ohm slowly. Change the rod to
different polarity, the reading repeat from zero to 9 mega ohm (FIG.5-5),it means the capacitor is normal. If the indicator of the
multi meter can’t point out from zero to 9 mega ohm, it indicates the high voltage capacitor has broken, and should be
replaced by a new one.

FIG5-5 FIG5-6

If it is normal between the two pole of the capacitor, then the insulation between the capacitor pole and the cabinet (FIG.5-6)
should be checked.
If the resistance value between the capacitor pole and the cabinet is “∞”,the capacitor is normal. Then check the earth of the
magnetron’s two filament to see whether they are short-circuited (FIG.5-7).If they are short-circuited and the filament strikes
the shell of the magnetron, it indicates the magnetron has broken, and should be replaced by a new, same model one.
If there is no problem with the magnetron, check the high voltage diode then. Measure the diode with Rx10k grade of a multi
meter, the “-” rod end of the multi meter connect the cathode of diode, the “+ “ rod end of the multi meter connect the anode of
the diode(FIG.5-8).The multi meter reading should be about 150 thousand ohm. Then change the rod to different
electrode(FIG.5-9), the reading should be “∞”.If the reading is very small, and near to short circuit, it indicates the high
voltage diode has been punctured, and should be replaced by a new one.
If high voltage diode is also normal, then test the pilot switch(FIG.5-10). Pull out the two plugs of the switch, Measure it with
the Rx1 grade of a multi meter, the two rod connect the plug of the switch, the resistance value should be “∞”.Then press
down the pilot switch with a screwdriver, if the reading of the multi meter pointed to zero, it indicates the pilot switch has
broken, and should replace it with a new, same model one.

FIG.5-8
FIG.5-7

5-5
 FIG5.10
FIG.5-9
Ⅲ.REPAIRING METHOD OF SEVERAL BREAKDOWN
1. Repair when there occurred large amounts microwave leakage. There are many factors, which may cause microwave leaking.
Following mentioned may be the main cause of microwave leakage:
(1) The door deformed, the hinge loosed or damaged that caused the door can not close tightly.
(2) The door pressing cover or the embed piece damaged or come off.
(3) Obvious damage or uneven of the oven.
(4) There are filth between the door and the oven.
(5) The door and the oven are serious loosed after the door closed.
(6) The crack of the door shielding net cover.
Before repairing, check whether the above listed point are existed, if not, you can start the microwave oven. Place a
graduate of about 275ml water at the middle of the glass tray, close the door, time set at 3 minutes, power at high,
makes the oven operating in normal. Rectify the microwave leakage measure, measure the amount of the microwave
leakage around the oven with its probe. If there are places which the leakage exceed the standard requirement, then
2
repair them accordingly. If the leakage amount exceed 1.0 mW/cm at the left door crack, then pull out the power plug,
take down the outer case, adjust the screws of the hinge to less the gap between the door and the oven. Then measure
2 2
again, the leakage amount should less than 1.0 mW/cm . Generally, it should be controlled below 0.8 mill watt/cm with
some allowance.
If the leakage occurred at the right door crack, adjust the screws that fix the interlock holder and the hook. If the leakage
is on the larger side at the right-above of the oven, then adjust the upper screw. Loosen out the screw, push the door
close to the oven to hook the door hook with the plastic parts, then tighten the screw again. If the leakage is larger at
the right-below, then adjust the lower screw. Loosen the screw, push the door close to the oven to hook the door hook
with the switch holder tightly, then tighten the screw again, and open and close the door repeatedly to check whether the
door can operate flexibly, whether the hook and the switch are in their normal position. If it is not in position, then adjust
the door hook and the switch holder the loose between the door and the oven, then measure the leakage with
microwave leakage measure again.
If there still exist microwave leakage, measure near the magnetron with the probe of the microwave leakage measure. If
the leakage is larger, the oven should be turned off and check whether the 2 or 4 screws which fix the magnetron have
been loosed, if loosed, twist them tightly with socket wrench. If the screws are fixedly, then the magnetron should be
take down to check the copper filament weaved washer of the magnetron has been placed well or whether the wave
guide housing coupling has been oxidized or have lacquer on it. If do have, scrape the oxidized layer or the lacquer off,
when fix the magnetron, the copper filament weaved washer must be placed well, the screws must be twist tightly. Then
turn on the oven and measure again until it complies with the requirement. If the microwave leakage is larger at those
hole position of the window board, the oven should be turned off to inspect whether there are crack among them. If
several holes formed a crack, it would enlarge the microwave leakage. If that is the case, it indicates the door has
broken, and should be replaced with a new door.

5-6
2. Means of repair when the oven can heat, but the turntable glass can’t move
Firstly, check whether the turntable holder is placed correctly. If it is correct, then pull out the power plug and take down the
turntable combination, measure the resistance value of the turntable motor with Rx1k grade of a multi meter If it is open-
circuited, it indicates the turntable motor has broken, and should be replaced by a new, same model one. If the resistance
value is between 15-22k,it indicates the turntable motor is normal, then check the connecting shaft weave. If the plastic that
the shaft insert in has broken, a new shaft weave should replace it.
3. Repair when the oven can heat, but the lamp is not on.
Pull out the power plug, take down the outer case and discharge the capacitor.
Pull out the two terminal plugs of the lamp, measure the two plugs of the lamp with the Rx100 grade of a multi meter. If it is
open-circuited, it indicates the lamp has broken, and should be replaced by a same model one.
4. Means of repair when the oven stop working after several minutes operating
The phenomenon indicated the thermal cutout is playing its protective role, and you should check whether the fan is working
in normal. Turn off the oven, pull out the power plug, take down the outer case, discharge the capacitor, then turn the fan with
hand to see whether it is moving flexibly. If not, it indicates that the oil bearing of the fan motor has run off the oil, and should
take down the fan combination to repair the motor. Loosen the two screws which fix the bearing out the shaft and the bearing,
and rinse them with kerosene (ATTENTION: The bearing can only be wiped with a silk which moistened with kerosene rather
than be washed in the kerosene because there are felt on it. If the felt are soaked with kerosene, then the engine oil can not
be sucked up.).After the bearing being cleaned, the felt should be refueled fully with engine oil(for when the oven is operating,
the engine oil empty into the oil bearing slowly).Fix the bearing cover with two screws, turn the fan around till it can move
flexibly. Than install them to the oven, and plug in the two terminal plugs.
If the fan can move flexibly, then the winding of the fan motor should be examined. Measure the winding with Rx100 grade of
a multi meter, if it is open-circuited, it indicates the winding of the fan motor has broken, and should be replaced by a new,
same model one.

5-7
 MOTOR TEST PROCEDURE
COMPONENTS TEST PROCEDURE RESULTS
Measure the resistance.
Fan Motor (Ohm-meter scale:R×100) Normal:Approx. 47Ω
(Wire leads removed)
Abnormal:∞ or Several Ω

Measure the resistance.

Turntable Motor (Ohm-meter scale:R×1000) Normal:Approx. 3.2kΩ
(Wire leads removed)
Abnormal:∞ or Several Ω

NOTE:
z A MICROWAVE LEAKGE TEST MUST ALWAYS BE PERFORMED WHEN THE UNIT IS
SERVICED FOR ANY REASON.
z MAKE SURE THE WIRE LEADS ARE IN THE CORRECT POSITION.
z WHEN REMOVING THE WIRE LEADS FROM THE PARTS,BE SURE TO GRASP THE
CONNECTOR ,NOT THE WIRES.

5-8
 COMMON BREAKDOWN AND MEANS OF REPAIRING
PHENOMENON CAUSE REPAIRING MEANS
1. fuse broken 1. Change a new fuse.
2. The primary and secondary winding of the 2. Change a new
transformer are short-circuited. transformer.
1.When starting the 3. The earthing or the polarity of the capacitor is 3. Change a new capacitor.
oven, the lamp is not on, punctured. 4. Change a new pilot
the turntable tray can’t 4. The pilot switch can’t cut off. switch.
rotate and the food can’t 5. The interlock switch hasn’t closed. 5. Change a new interlock
be heated 6. The power plug and the socket are not in good switch.
connection. 6. Adjust the connection or
7. The door hook broken. replace it by a new one.
7. Change a new book.
2.When starting the 1. The primary and secondary winding, the 1. Change a new
oven, the lamp is on, the filament of the transformer are open-circuited. transformer.
turntable rotating, the fan 2. The magnetron filament is open-circuited, the 2. Change the magnetron.
cycling but the food can’t magnetic steel of the magnetron broken or the 3. Change the time power
be heated. magnetron is air leaking. distributor or the micro-
3. Time and power distributor broken.. switch.
4. The plugs of the magnetron of the capacitor 4. Fix them.
loosed.
3.The food can be 1. The lamp broken. 1. Change a new lamp
heated, but the lamp is 2. The plug fall off. 2. Insert the plug again
not on.
4.The food can be 1. The turntable motor broken 1. Change the turntable
heated but the turntable 2. The plug fall off motor
tray is not rotating. 3. Connecting shaft weave broken 2. Insert the plug securely
3. Change the weave
5.The oven can heat 1. The winding of the fan motor in open-circuited. 1. Change the fan motor
within 2-3 minutes, but 2. The fan falls off 2. Change the fan
can not heat from the 3. The plug of the fan motor falls off 3. Insert the plug
fourth minutes. 4. The turntable shaft is griped with the motor 4. Overhauling them
bearing. 5. Repairing it
5. The cooling vent blocked
6.When starting the The high voltage diode was punctured Change a new diode
oven, it can’t heat, and
with “wenwen” noise
7.The oven can heat,but The iron core of the transformer loosed Change a new transformer
with sound “shishi” noise
8.Large amount of 1. The door deformed 1. Mend the door
microwave leakage 2. The door metal net cracked 2. Change the door
3. The gap of the door crack is too large 3. Adjust the gap
4. The welding point of the oven fall off 4. Change the oven
5. The screws which fix the magnetron loosed 5. Tighten the screws
6. The wave guide connection oxidized 6. Scrape the oxidized and
7. The magnetron copper filament washer is too tighten the screws
thin cause the wave guide opening not in good 7. Thick the copper filament
earth. washer
9.The door can’t open 1. After long time using, the wear and the rust- 1. Adjust the hinge to rectify
eaten enlarged the gap of the door shaft and the position of the door.
the shaft hole, thus cause the door crooked. 2. Change the hook
2. The door hook broken
10.The door release Wore aged after long time operating Overhaul it or renew it
button fall off
11.Electricity leaking The earthing insulation resistances of all the Test where is the leaking
motors or the transformer are less than 2 mega place, then repair it or
ohm. change those damaged
components.

5-9
 IMPORTANT THINGS TO DO PRIOR TO CRITICAL PART
SERVICING
The following instructions are CRITICAL to the owner’s safety. Be sure to follow all the instructions. Contact the
manufacturer of distributor if you have any question.

1.1 If the oven is operative prior to servicing a Microwave Leakage Test (Microwave Emission Check) should be
performed prior to servicing the oven.
2
1.2 in the event that any microwave oven found to have microwave emission level in excess of 1 mW/cm .The
following procedures should be followed:
a. Inform the distributor, importer, or manufacture the finding. Record it in the logbooks well.
b. Repair the unit at no cost to the owner.
c. Investigate the oven and ascertain the cause of the excessive leakage.
d. Hold the oven in your facility and instruct the owner not to use the unit until the oven has been brought into
compliance.
1.3 In the event that the oven operates with the door open. The following procedures should be followed:
a. Tell the user not to operate the oven.
b. Hold the oven in your facility until it is investigated and repaired.
c. Contact the manufacturer immediately.

2. Interlock Assembly Replacement and Adjustment

2.1 If you suspect defective primary, secondary or monitor interlock switches, use your ohmmeter(digital or analog
type the check the electrical continuity.
2.2 Make sure the power cord is pulled out and the high-voltage capacitor is discharged before the electrical
continuity check.
2.3 Set the ohmmeter to “Low Resistance” range and connect both leads (alligator clips) to the switch terminals.
2.4 Open the door and notice the meter reading. The primary or secondary interlock switch should show an “infinite”
resistance when the door is open. Replace it when it is defective. The monitor interlock should show a “zero or
near zero” resistance when the door is open. When the door is closed, the readings will be opposite.
2.5 If the oven has been received inoperative due to the failure of the monitored safety(primary and/or secondary)
interlock(s),you should replace all of the monitored safety interlock switched and the monitor switch.
3. Door and Hinge Replacement and Adjustment
3.1 Pull the power cord from the outlet. Check the door for warped or damaged areas. Check the hinges for broken
or worn areas. Check other areas such as cracked from glass, broken door latched, worn/cracked viewing
screen and etc.
3.2 After determining the door assembly should be replaced, check the parts list for the correct part number. All oven
door components must be ordered directly from the manufacturer or its authorized distributor.

4. Magnetron Replacement
4.1 Check for the presence of the wire mesh gasket before installation.

4.2 Conduct a Microwave Leakage Test at the magnetron area prior to installing the top cover.

5-10
 SAFETY CHECKS AND TESTS AFTER SERVING
Constructional Checks

If mechanical or electrical(electronic) parts have been replaced be sure to follow the following steps.

1.1 Check for correct wiring, adequate mechanical decrements of parts, and firm connectors.

1.2 Check for adequate grounding.

1.3 Check the following items before turning the oven ON.

1) Proper door closing, seal/choke surfaces, and hinges.

2) No outer case damage.

3) Proper interlock and monitor operations.

Insulation Resistance Test

If the low voltage power supply has been repaired, use a 500 V Mega ohmmeter to measure the resistance between the
primary(Line and Neutral)of the power plug and operator accessible metal parts. The resistance should be no less than 2 Mega
Ohms. Repair the oven again when necessary.

5-11
 1 2 3 4 5 6 7 8

C101
R103
EE16
T100
+12V 20R
D100 D101 E100 E101 C100 R101 10 102,1KV +12
CN100 1N4007 1N4007 4.7uF,400V4.7uF,400V 102,1KV 100K 1 D106 @250mA
12V
2
BUZ1 5 R102 UF4002 E103 R106VCC
100K 3 9
8 L100
R1 LED share kathode R100
IN 5V D107 470uF,25V 4.7uH,0.3A 4K7 @250mA
3.3k （共阴极数码管） 100R 4
7
6 UF4002 E102 E104
LED: 5X8 3 470uF,25V 220uF,16V
D D102 D
TR1 线绕电阻 1N4007 R105
RX R104 270R
R3 1

5
560R

1
BUZZER 22R,2W
VH5-3 IC100
4.7K LED1 8 LNK364

D
S IC101
R2 4 3 2 Z100
8050 FB
2K 7 1N5229B,4.3V
S
3 4 1
R107 BP 输出电压调节：5V高减少R106，5V低加
2
S PC817

S
D103 D104 C102 大R106。
3K9
1N4007 1N4007 104 但必须保证Z100工作在额定条件。
L101 R108

1
D1
2.2mH,0.1A

6
20K

13

12

11

10
此主板上留有一个10pin的插座J1,用以和按键板相连. 4148
RY IC102 R109 ZERO
a b c d e f g dp 1 4
220K,1W 1K
2 3 C103
R14 R15 R16 R17 R18 R19 R20 R21 102
D2 PC817
4148 VCC

J1 330 330 330 330 330 330 330 330

D3 R27
10 4148 10K
9 RLY1
TR2
8 R29
7
1K R7 键输出 8050
J GRILL
6
1K R8 键输出 3K3
C 5
1K R9 键输出 D4 烧烤型/非烧烤型的区别:
R28 C
4
2K R10 键输入3 4148 1.烧烤型不装R27,仅装烧烤部分电路(包括R28).
20K
D11
3
2K R11 键输入2 2.非烧烤型只装R27,包括R28 在内的烧烤部分电路不安装. 4148
2
2K R12 键输入1
1
2K R13 键输入0
D5
CON10 4148
RLY2
IC1 TR3
15 14 R30 8050
LED-D/PH1 PH0/LED-D J MICRO
3K3
16 13 LED5 4K7 R22 SWE1
LED-D/PD2 PD1/LED-C
C6 C7 C8 C9 D10 4148
17 12 LED-4 4K7 R23 SWD1
LED-D/PD3 PD0/LED-C
471 471 471 471
18 11 LED-3 4K7 R24 SWC1
LED-D/PB0 PA3/LED-C
19 10 LED-2 4K7 R25 SWB1
LED-D/PB1 PA2/LED-C
20 9 LED-1 4K7 R26 SWA1
LED-D/PB2 PA1/LED-C
SINO

VCC 21 8
LED-D/PB3 PA0/LED-C
22 7 C15
VDD GND
SH69P26

C13
23 6 0.1uFRESET R39
CSA1
OSCI/PC0 PC3/RESER VCC
4MHz
1K
15P 24 5 microwave
B OSCO/PC1 PC2/T0 B
VCC
C14 BUZZER 25 4 GRILL
TONE/PF0 PE0/CMPO
R31 R34 26 3 lamp/FAN
T2/PF1 PE1/CMPN
20K 10K 15P
R55 27 2
PF2 PE2/CMP1
100K VCC
DOOR 28 1 ZERO
PF3 PE3/CMP2
SH69P26-28PIN R35
R32 R38
10K
2K 1K
C11 C12 2K D12 DOOR1
DOOR R33
C10 +12
4148
471 471 C16 VCC 471
0.1uF N

R41 R36
RLY3
TR4
4.7K 10K R40 8050 TR7
J
1K 8550
R43 R37
TR6 D13 4148 MOTOR
8550 220 10K C17
10uF/16V
4.7K R42
A A

Title

Size Number Revision

V1.0A
A3
Date: 18-Sep-2012 Sheet of
File: D:\MyData\桌面\临时文件夹\AGXEEZ~1.DDB
Drawn By:
1 2 3 4 5 6 7 8
 1 2 3 4 5 6

D D

SW4（解冻） SW6（暂停/ 取消）

SW1(微波）

C
SW2（烧烤/ 组合） J2 七键一旋按键板标准原理图说明： C
1
SW3（热风对流） SW5（时钟/ 预约） SW7（开始/+30 秒）
2 1. 按键：七个
3
4
2. 编码开关：一个
5 3. 排线：一组(九根或十根)
6 4. 九针(或十根)的排线连接插针：焊接到按键板上
7
8 5. 十针的插头，用以连接到主板上(请注意：主板上的为10PIN的插座)
9
B1 10
PCB布板注意:
CON10
SW_CONDER
1.主板上与按键板之间的连接插座为10PIN,且10 脚在上(为GND).
2.主板上的连接插座凹槽朝外，若凹槽朝里，则按键板使用异向排线与主板连接
编码开关 3.按键板上的排线第10 根线在上,为GND连接线.

B B

A A

Title

Size Number Revision

B
Date: 18-Sep-2012 Sheet of
File: D:\MyData\桌面\临时文件夹\按键板~1.DDB
Drawn By:
1 2 3 4 5 6
AG930AZJ
E02

E04

E02

WIRE 温控器连接线
E02 HEATER

E04 WIRE HEATER_THERMOSTA

温控器连接线

E02 W IRE HERMOSTAT_FILTE

滤波板连接线 T

AG930AZJ-P00C
Model ：AG930AZJ-P00C/MD930GXE
Part name Description
Material code Qty. position
(English) （English）
H.V.Transfor
mer MD-
H.V.Transfor
251200200368 901CMR-1 1 E05
mer
YLE
220V/50Hz
H.V.Transfor
mer 220V
H.V.Transfor
261200202090 50Hz 900W 1 E05
mer
MD-901CMR-
1 MIDEA
Magnetron
251200100068 Magnetron 2M219J-E522 1 E01
900W
Outer Cover
261502637100 Outer Cover A28L PCM 1 Z24
T=0.5
PCM white
color plate
outer cover
T=0.5 with
251502610243 Outer Cover blue easy-to- 1 Z24
tear film and
packge
stuff(ref.2515
02600410)
RoHS Bottom
Plate,
E25L/E28L
251501400079 Bottom Plate SGCC T=0.7 1 B01
with packge
stuff(ref.2521
00500013)
RoHS
Turntable
262100500002 Turntable 1 T04
315mm 1260g
30mm
T-T Ring
T-T Ring Ass'y
262200200017 1 T03
Ass'y Φ222mm
Φ15mm
 Fan Motor
MDT-10CEF
WLB2 YZ-
261200600350 Fan Motor 1 W03
E6120-M02K
25120060014
8
Fan Motor 220-
251200600161 Fan Motor 240V 50Hz 1 W03
MDT-10CEF

Fan Motor 220-

261200600690 Fan Motor 240V 50Hz 1 W03
MDT-10CEF
RoHS fan
blade with
261300900400 Fan packge stuff 1 W02
60 pcs/ctn, 10
layers
Turntable
Motor MDS-
Turntable 4A(BTTB) 220-
261200300080 1 T01
Motor 240V50Hz60
Hz CL.B
EKXINTE
RoHS
Capacitor
Capacitor Clamp C23L
261501500301 1 Z01
Clamp SGCC T=0.5
with packge
stuff
RoHS
Harness
EG031A-
261202807130 Harness 1 L05
P00E-H2
(1569) with
packge stuff
RoHS Fan
Support
251300800011 Fan Support HG23L PP 1 W01
with packge
stuff
Switch
Switch
261301301600 Support A28L 1 L01
Support
PBT
Lamp
263600500006 Lamp 240V25W T25 1 E13
（MD ）
 Lamp
263600500007 Lamp 240V25W T25 1 E13
（MD ）
Lamp
253600503976 Lamp 240V25W T25 1 E13
KEI
RoHS Control
251300201833 Control Panel 1 C01
Panel
PENDING
Control Panel
251505900248 FOR YOUR 1 C02
Dec.
ARTWORK

251200701304 H.V.Capacitor H.V.Capacitor 1 E06

251200701657 H.V.Capacitor H.V.Capacitor 1 E06

RoHS Power
Cord H05RN-
256201000383 Power Cord F 1 E16
3*1.00mm^2
black
Upper Upper
261502701300 Insulating Insulating 1 G09
Plate Plate
Quartz Quartz
251501000005 1 G06
Supporter Supporter
RoHSConnect
251202700230 Connector or 120mm 1 E04+E21
(3122)
Grill Tube Grill Tube
251202701535 1 E04+E21
Connector Connector
RoHS Grill
256511700634 Grill Bracket 1 *
Bracket
RoHS Dial
251301600165 Dial Knob 1 C10
Knob
RoHS Quartz
Tube SH-
251200410024 Quartz Tube 50C2511 2 G02
110V/500W
187*2 HG23L
PENDING
Control
251304900206 FOR YOUR 1 C14
Window
ARTWORK
RoHS Lower
Hinge
assembly
256502500868 Lower Hinge 1 B03
apply to new
Platform,elect
roplating
 Mica Plate, ref
25210011001
262100100003 Mica Plate 1 A01
6 , 500
pcs/box
AG930AZJ炉门组
Door Ass'y Door Ass'y 1 *
件
Button Row
251301910012 Button Row 1 C20
A30L ZJ
RoHS
H.V.Diode
CL01-12 12KV
251200900861 H.V.Diode 1 E07
350mA 187
FUXIN with
cover
12KV 350mA
261200900030 H.V.Diode 1 E07
CL01-12
12KV 350mA
251200900954 H.V.Diode 1 E07
T3512 中环
Harness
between filter
251202701048 Harness 1 E02
and
magnetron
H.V.Fuse GERF-
251203301548 H.V.Fuse Ⅱ 800mA 1 E28
SONGSHAN
H.V.Fuse
261203300080 H.V.Fuse 800mA 5KV 1 E28
721
Fuse
261201200030 Fuse T10AH250（2 1 E11
50V10A ）
RoHS Fuse
T10AH250
251201200025 Fuse 1 E11
φ5*20mm
Better
RoHS
Thermostat
Thermostat
251201300630 90/80 10A 1 E30
90
250V KSD201
187#
RoHS
Thermostat Thermostat
251201300691 1 E30
90 90/80 10A
250V KSD90
RoHS
Thermostat Thermostat
261201300720 1 E30
90 90/80 10A
250V KSD1
 RoHS
Thermostat
Thermostat
251201300033 150 /90 10A 1 E37
150
250V KSD201
187#Vertical

RoHS
Thermostat Thermostat
251201300064 1 E37
150 150 /90 10A
250V KSD150
RoHS
Thermostat Thermostat
251201300042 1 E37
150 150 /90 10A
250V KSD1
RoHS Metal
Air Guide
261503202100 Air Guide 1 W04
A28L SGCC
0.5mm
RoHS
Interlock
Interlock Switch KW3A-
251201600002 2 L03
Switch 10T-t OPEN
16A 250V
T105 187
RoHS
Interlock
Interlock
261201600080 Switch 16A 2 L03
Switch
250V T105 LF-
10-02
RoHS
Interlock
Interlock
261201600180 Switch 16A 2 L03
Switch
250V T125 HK-
14
RoHS Monitor
Switch, KW3A-
Monitor 10Z-t, 16A
251201600003 1 L04
Switch 250V
T105,187
terminal

RoHS Monitor
Monitor Switch, 16A
261201600070 1 L04
Switch 250V T105 LF-
10-02
 RoHS Monitor
Monitor Switch, 16A
261201600160 1 L04
Switch 250V T125
HK-14
RoHS Wire
252000600000 Wire Binder 2 *
Binder white
RoHS Cavity
Lamp Cover
Cavity Lamp
252200400440 A28L PET 1 Z15
Cover
T=0.1
93*96.5
Interlock
Interlock Lever
261301101000 1 L02
Lever E25L/A23L/A
28L
RoHS T-T
Driver HG23L
252200100008 T-T Driver 1 T02
PPS
7130140008
RoHS Air
Air Guide Guide
252200700003 1 *
Sponge Sponge, 17L
7130790001
RoHS Foot
apply to new
256302002770 Foot 4 B02
platform,
black PPT30
251500100325 Cavity 1 A00
Packing Pad Packing Pad
251920000516 1 *
*I A28L
RoHS Filter
256400300033 Filter 1 E10
MDFLT25A
Pressure
Capacitor,CT
Pressure 7
262011 2 C2、C3
Capacitor 222M/250VA
C length
3.5±1MM
Capacitor
0.1uF/275VA
262001 Capacitor C X2, 1 C1
distance
15mm
 T18*12*8
，QACC-1
Φ1.0,
18Ts，1.7-
Sieve
266004 6.5mH 1 FILTER
Inducrance
，1KHZ
0.1V
length：8.5±1
mm
Fuse Seat
5×9.5, with
268005 Fuse Seat φ5*20 fuse, 2 FUSE
foot length
3.5±1MM
Base
Line,125mm
AWM 1015
18AWG
265001 Base Line 1 GND
yellow and
green wire,
length
4.5±1MM
187
Connection-
Connection- Peg
269004 4 N）、L（OUT）、N（OUT）
Peg 4.8*0.5mm,
length
3.5±1MM
Carbon
Resistor
Carbon 510K/1/2W
261003 1 R1
Resistor ±5%, distance
15mm length
4±1MM
PCB
MDFLT25A,F
R-1/94V0,
264020 PCB 1 *
thickness
1.6mm，lengt
h 58*width 40
258601000069 Scrow Ass'y Scrow Ass'y 1 *
ROHS screw Power cord
257012500002 screw gasket gasket 1 grounding-
diameter 4.1 rear plate*1
tt motor-tt
RoHSScrew
257012800001 Screw 1 motor
ST4*8PBHC
support*1
 H.V
tranformer-
base plate*4;
H.V
Diode－capac
itor
clamp－base
plate*1;
Power cord
grounding-
rear
plate*1;upper
ROHS Screw
hinge ass'y-
257012800003 Screw 5# 17
cavity*2;
CT4*8TBHC
Upper
Insulating
Plate-
cavity*2；
magnetron-
magnetron
support*3；lo
wer hinge
ass'y-
cavity*2；Air
guide*1;filter
grounding-
Fan
RoHS Screw
257012800016 Screw 2 motor－Fan
4*25TWBHC
support*2
Thermostat-
OHS Screw
magnetron*2;
257012800009 Screw ST3*10PWTH 3
Filter-Fan
C（
support*1
Fan support-
rear
ROHS Screw plate*1COntro
257012800027 Screw ST4*12PWBH 4 l panel-front
C plate*1;switch
support-front
plate*2
ourter
cover－base
ROHS Screw plate*3;ourter
257012800032 Screw 8
26# 4*10TDB cover-rear
plate*2;base
plate-cavity*3
 AGLEEZG-
261400125760 PCB 1 C18
03-K-CKD
RoHS
electrolytical
capacitance
electrolytical E_4u7_400_D
263001200022 2 E100,E101
capacitance 10H15_M_10
5_CKD(feet
distance
5.0mm)
ROHS
Electrolytical
electrolytical capacitance
253001200195 2 E102,E103
capacitance E_470u_25_D
8H14_M_105_
CKD, 5.0mm
RoHS
Electrolytical
capacitance
electrolytical
253001200197 E_220u_16_D 1 E104
capacitance
6.3H11_M_10
5_CKD,
5.0mm
RoHS
electrolytical
capacitance
electrolytical
263001200036 E_10u_50_D5 1 C17
capacitance
H11_M_105(f
eet distance
5.0mm)
RoHS plug
CN_VH-
253005500206 plug 1 CN100
5A_B3P7.92_
W_CKD
ROHS high-
voltage
porcelain
high-voltage capacitor
263001000018 porcelain C_102_1KV_ 2 C100,C101
capacitor Y5P_M_F5.0_
CKD(feet
distance5.0m
m)
ROHS
optocoupler
263005000024 optocoupler 2 IC101,IC102
IC_817C_4PI
N_DIP
263005000022 optocoupler IC101,IC102
ROHS
263005000025 IC IC_LNK364P 1 IC100
N_8PIN_DIP
Switch
Transformer
263005200033 transformer T_DZ16003- 1 T100
X_230V-50Hz-
CKD
ROHS color
wheel
color wheel inductors
263005300001 1 L100
inductors L_LGA0410-
4R7KT52E_4.
7uH K T52
ROHS color
wheel
color wheel inductors
263005300002 1 L101
inductors L_LGA0410-
222KT52E_2.
2mH K T52
ROHS metal
oxide film
metal oxide
263000100004 resistors 1 RY
film resistors
RY_220K_1W
_J
ROHS carbon
wire-wound film resistor
263000200001 1 RX
resistors RX_22R_2W_
J
ROHS plug
for door
socket,CN_V
253005500205 plug 1 DOOR1
H-
2A_B2P3.96_
W CKD
ROHS plug
for connector
socket
263005500068 plug 1 CON10
CN_XH-
3A_B3P2.54_
W
RoHS Buzzer
253005900218 Buzzer BUZ_2020P_ 1 BUZ1
2K_立_CKD
 RoHS Relay
RLY_ZW_JQ
253005100075 Relay X- 1 RLY1(GRILL)
78F_T85_12V
DC_H
ROHS Relay
RLY_SC_302
RLY2(MICRO
253005100002 Relay WP-1AH- 1
)
C_T85_12VD
C_H
ROHS Relay
RLY_ZW_JZC- RLY4(MOTO
253005100003 Relay 1
40F_T85_12V R)
DC_H

Digital tube
MDA-
263003000511 Digital tube 3482AHG_CK 1 LED1
D 45*35*21.5
red/green

ROHS Crystal
Crystal oscillator
253005400233 1 CSA1
oscillator OSC_4M_2_3
0PPM_CKD

ROHS empty
chip SH69P26
sinle-chip
chip with
251402200958 microcompute 1 IC1
program of
rs
AG(M)XEEZB-
06-R-V1.4B

RoHS
Rectification
Rectification diode
253002000204 5 D100-D104
diode D_1N4007_1
KV_DO-
41 CKD
RoHS Ultra
Fast
Ultra Fast Recovery
263002000015 Recovery RectifierD_UF 2 D106,D107
Rectifier 4002_1A_100
V_D0-
41 CKD(T52)
 ROHS Zener
diodeZ_4V3_1
263002200009 Zener diode 1 Z100
/2W_B_DO-
35_CKD(T52)
ROHS Switch
diode
263002000005 Switch diode D_1N4148_15 1 D12
0mA_100V_D
O-35_CKD
RoHS Smt
CAP
253001100179 Smt CAP C_0805_471_ 7 C6～C12
50_X7R_K_C
KD
RoHS Smt
CAP
C15,C16,C10
253001100178 Smt CAP C_0805_104_ 3
2
50_Y5V_Z_C
KD
RoHS Smt
CAPC_0805_
253001100246 Smt CAP 2 C13, C14
15P_50_NPO
_J_CKD
RoHS Smt
CAP
253001100182 Smt CAP C_0805_103_ 1 C103
50_X7R_K_C
KD
ROHS Smt
Resistor JR1,JR2,JR4
253000400043 Smt Resistor 5
R_1206_0R_1 ～JR6
/8W_J_CKD
ROHS Smt
Resistor
253000400040 Smt Resistor 1 JR3
R_0805_0R_1
/10W_J_CKD
ROHS Smt
Resistor
253000400041 Smt Resistor R_0805_202_ 3 R2 ,R32,R33
1/10W_J_CK
D
RoHS Smt
Resistor R14～R21,R1
253000400036 Smt Resistor 9
R_0805_330R 05
_1/10W_J
 ROHS Smt
Resistor
253000400042 Smt Resistor R_0805_332_ 3 R1,R29,R30
1/10W_J_CK
D
ROHS Smt
Resistor
253000400035 Smt Resistor 1 R43
R_0805_220_
1/10W_J
ROHS Smt
Resistor R3,R22～R26
253000400046 Smt Resistor R_0805_472_ 9 ,R41,R42,R10
1/10W_J_CK 6
D
ROHS Smt
Resistor
253000400044 Smt Resistor R_0805_103_ 4 R34～R37
1/10W_J_CK
D
ROHS Smt
Resistor
R28,R31,R10
253000400045 Smt Resistor R_0805_203_ 3
9
1/10W_J_CK
D
ROHS Smt
Resistor R7～R13,R38
253000400047 Smt Resistor R_0805_102_ 12 ～R40,R104,
1/10W_J_CK R110
D
RoHS Smt
Resistor
253000400102 Smt Resistor R_0805_104_ 2 R102,R111
1/10W_J_CK
D
ROHS Smt
Resistor
253000400097 Smt Resistor 1 R101
R_0805_100R
_1/10W_J
RoHS Smt
Resistor
263000400028 Smt Resistor 1 R103
R_0805_20R_
1/10W_J
RoHS Smt
Resistor
263000400024 Smt Resistor R_0805_392_ 1 R107
1/10W_J_CK
D
 RoHS Smt
Diode
D_1N4148W_
263002300004 Smt Diode 3 D10,D11,D13
150mA_100V
_SOD-123
（塑封）
ROHS SMT
Triode
TR1,TR2,TR3
253002400048 SMT Triode Q_S8550M- 4
,TR4
D_SOT-
23_CKD
ROHS SMT
Triode
253002400050 SMT Triode Q_S8550M- 2 TR6,TR7
D_SOT-
23_CKD
ROHS jumper
J_Cu-
253006100058 jumper 6 J1-J5,J16
Sn_D0.6_7.5
mm
ROHS jumper
J_Cu-
253006100056 jumper 8 J6-J13
Sn_D0.6_10m
m
ROHS jumper
J_Cu-
253006100083 jumper 3 J14,J17,J18
Sn_D0.6_12.5
mm
ROHS jumper
J_Cu-
253006100077 jumper 1 J15
Sn_D0.6_15m
m
PCB
AG(M)XEEZG-
03-K-CKD
263006000821 PCB 1 PCB
152*65.5
1.6mm CEM-
1 ZD V1.0
KEY BOARD
ROHS
connecting
curve
connecting
263005500096 CP_XH_JC25 1 CON10
curve
_26AWG_10P
100_80_S_CK
D
 RoHS Coding
Switch
253005700085 Coding Switch B_EC16P24L 1 B1
20F12V-
2_26.5_CKD
ROHS Tact
Switch
KEY_6X6X5_
263005600003 Tact Switch 180±40gf_CK 7 SW1-SW7
D（feet
distance
5.0mm）
PCB PCBKEY-
ZJ-R
263006000227 PCB 146*68.5 1 KEY-ZJ
1.6mm FR-1
KB V1.0