A320 Line Training: Last Updated
A320 Line Training: Last Updated
A320 Line Training: Last Updated
MISC REFERENCES
NOISE ABATEMENT
PERFORMANCE
WEATHER RADAR
DISCLAIMER
COMMON ITEMS ALREADY EXPLAINED
Refer to ATR Line training Syllabus:
http://www.theairlinepilots.com/forumarchive/atr/atr-line-training.pdf
MISC REFERENCES
2) Normal Procedures:
https://www.theairlinepilots.com/forumarchive/a320/a320-normal-procedures.pdf
3) Abnormal Procedures:
https://www.theairlinepilots.com/forumarchive/a320/a320-abnormal-procedures.pdf
5) Limitations:
https://www.theairlinepilots.com/forumarchive/a320/a320-limitations.pdf
6) Memory Items:
https://www.theairlinepilots.com/forumarchive/a320/a320-memory-items.pdf
8) Miscellaneous:
https://www.theairlinepilots.com/forumarchive/a320/a320-misc-references.pdf
A320 SPECIFIC ITEMS IN CFP
A1 – RNAV10 (RNP10)
B2 – RNAV5 GNSS
B3 – RNAV5 DME/DME
B4 – RNAV5 VOR/DME
D1 – RNAV1 All Permitted Sensors
L1 – RNP4
O1 – Basic RNP1 All Permitted Sensors
S2 – RNP APCH with BARO VNAV
Note: If you have all sensors then you just file the first option. E.g. D is for RNAV 1. It has 4 categories
i.e. D1, D2, D3, and D4. D2 is if you have GNSS sensor, D3 if DME/DME, D4 if DME/DME/IRU. If you
have all of them then just file D1 that stands for all permitted sensors.
For more details on these fields and items refer to: https://contentzone.eurocontrol.int/fpl/
Endurance 3:26
Persons on board: To be Notified.
Emergency radio: VHF and ELT.
Survival equipment: Maritime.
Jacket: Light and fluorescent.
Dinghies: 6 with a total capacity of 180 (30 in each), color yellow.
LOAD AND TRIM SHEET
MEL REPAIR INTERVALS
Note: Older NADP A and B are no longer part of the ICAO PANS-OPS Doc. 8168.
For more details refer to: http://www.theairlinepilots.com/forum/viewtopic.php?t=192
FMS RELATED STUFF
FMS Pages: For a quick review see: https://www.theairlinepilots.com/forumarchive/a320/a320-fms-pages.pdf
• Check the direct distance and fuel on FMS page: DATA > CLOSEST AIRPORT
• Secondary > Copy Active
• Lateral Revision from point of diversion > Change Destination
• Lateral Revision from point of diversion > Build the flight plan
Departure / Arrival have 2 pages. Transitions are on the second page. If you just want to change a transition without
changing the runway, just go to next page and do it, instead of removing and adding the runway again.
Maximum Altitude:
• It is based on current engine and wing performance and does not take into account the cost aspect.
• Performance factors involved are current gross weight, temperature and assuming anti-ice off.
o Maximum altitude at maximum climb thrust with 300 ft/min vertical speed.
• If the crew inserts a FL higher than REC MAX into the MCDU, it will be accepted only if it provides a buffet margin
greater than 0.2 g. Otherwise, it will be rejected and the message "CRZ ABOVE MAX FL" will appear on the MCDU
scratchpad. This message may also be triggered in case of temperature increase leading the aircraft to fly above
the REC MAX FL.
• Unless there are overriding operational considerations, e.g. either to accept a cruise FL higher than REC MAX or
to be held significantly lower for a long period, REC MAX should be considered as the upper cruise limit.
• If one engine is out, this field (REC MAX) in FMS displays the recommended maximum engine-out altitude, that is
computed based on the long-range cruise speed and assuming that anti-ice is off.
Optimum Altitude
• It is based on best specific range i.e. maximum distance per kilogram of fuel and takes into account the cost aspect.
If there is a STEP in the F-PLN, ensure that wind is properly set at first waypoint beyond the step at both initial (the one
cruising at) and step FL (the one you will be climbing to at step). If you don’t have wind for the step level, insert the same
for the level you were cruising on.
A new flight plan can be created in the SEC flight plan inflight through its INIT & PERF pages. If a SEC flight plan already
exists then origin / destination pair cannot be changed without first deleting the existing SEC F-PLN. Four-letter origin &
destination is a must to create a new flight plan in secondary’s INIT page. The new route created in secondary (or primary
during preflight) can be stored by going to the stored routes page and then selecting "Store Secondary" (or primary).
To create a new runway first get the coordinates for the location where runway is to be made. This can be done on the FIX
page by the Place/Bearing/Distance method to create a point and then noting its coordinates. Using these coordinates, you
can then create a runway. NAVAIDS like ILS / VOR can then be added to this runway.
While creating a new runway, the runway IDENT comprises of the airport identification and the runway direction. You can
use six or seven digits e.g. CYYZ24L and LFRJ08. A new runway is identified by the first 4 letters (ICAO airport identifier)
of the runway ident although all 6 or 7 letters/digits have to be entered while creating the runway. First four letters can be
any alphabets like even ABCD. So, if you created a runway ABCD36R and you want to use this as the origin airport for
creating a new route to OPLA then in the origin/destination pair you will enter ABCD/OPLA.
• It’s given in the "Waypoint Name/ -Distance" format e.g. MOLTA/ -25 meaning that ETP is 25 nm short of MOLTA.
• Next create and insert a waypoint in the flight plan that corresponds to the ETP location. According to the above
example it will be MOLTA/-25.
• From this created point (which corresponds to ETP location), carry out a lateral revision and change the destination.
• Then lateral revision from the same point to build the routing.
Each FMGC computes a vector from its MIX IRS position to the radio position or GPIRS position. This vector is called the
“BIAS”. Each FMGC updates its bias continuously as long as a radio position or a GPIRS position is available. If an FMGC
loses its radio/GPIRS position, it memorizes the bias and uses it to compute the FM position, which equals the MIX IRS
position plus the bias. Until the radio or the GPIRS position is restored, the bias does not change. The flight crew can update
the FM position manually. This also updates the BIAS.
If this feature is installed it is used for manual position update. It appears on the PROG page when you deselect the GPS
from DATA > POS MONITOR > SEL NAVAID > DESELECT GPS.
Among other indications, it can be simply identified with FD status on PFD e.g. if no 2 FMGC fails then instead of 1FD2 the
FD status on PFD will indicate 1FD1.
Note: In managed guidance, FCU window is dashed. 45 secs for HDG/TRK and V/S & 10 secs for SPD/MACH.
PERFORMANCE
Takeoff Performance
Landing Performance
Dry Check:
On wet and contaminated runways, the screen height is reduced to 15 feet (instead of 35 feet that is used for dry runways).
Using the 15 feet screen height and/or reverse thrust for performance can sometimes (in some conditions) end up in max
TOW (or flex temperature) to be higher than that obtained for a dry runway. Regulations do not permit max TOW to increase
beyond dry takeoff weight. Therefore, it is mandatory to compare both dry and wet charts and retain the lower of the two
weights (or flex temperature) and the associated speeds determined for a wet runway. This is known as dry check. There
is no need to do a dry check if the top of the wet chart specifies “DRY CHECK” as comparison has already been inserted in
the wet runway calculation.
Disclaimer: "A320 Line Training" are personal notes of the undersigned for training only. These notes do not sanction any pilot
to violate his/her Company's Standard Operating Procedures, Aircraft Manuals or Manufacturer's Recommendations.