401CD User Manuel 220810-Coban
401CD User Manuel 220810-Coban
In order to protect the environment and provide timely up-to-date information about your
tracker, we have made electronicuser manual。
Todownload your electronicuser manual, please visit our website:www.baanooliot.com
401CD-V1.0
Contents
1. SPECIFICATIONS........................................................................................................................................2
2. TERMINAL INSTALLATION.....................................................................................................................3
4. MOBILE APP................................................................................................................................................ 4
BIND DEVICE....................................................................................................................................................... 4
7. FUNCTION DETAILS..................................................................................................................................7
1
7.24 CONFIGURE SMS MONITORING CENTER NUMBER..................................................................................18
7.25 CONFIGURE GPRS HEARTBEAT PACKAGE INTERVAL.............................................................................. 18
7.26 INITIALIZATION.......................................................................................................................................18
8. CAUTIONS.................................................................................................................................................. 19
9. TROUBLESHOOTING.............................................................................................................................. 19
1. Specifications
2
2. TERMINAL INSTALLATION
Please ask a qualified engineer to install it.
The installation environment should ensure that the GSM and GPS signals are good
Please do not install it in a dusty and humid environment.
Find the 5PIN wiring harness provided with the product, insert it into the corresponding wiring hole of the
product, and connect to the original car circuit as shown in the following Wiring Diagram:
Wiring Diagram
SIM card installation
Open sealed buckle of sim card, insert the simcard , then ,Put sealed buckle back.
Please be sure to confirm that the SIM card network frequency band is the network frequency
band supported by the device. Caller ID must be turned on and the PIN code must be turned
off. The call forwarding function cannot be turned on.
After inserting the SIM card, the GPS device will power on automatically
Green LED: In GSM Mode, LED flash one time for each second, In GPRS Mode, LED flash one time
3
Blue LED: Flashes one time every second when GPS signal is normal; flashes 3 times per second when
GPS signal is very good (at least 4 satellites with a signal-to-noise ratio of more than 38). And it turns off if
4. MOBILE APP
Register
Open BAANOOL IOT, register a new account and login, Choose “BAANOOL car “to enter
it.
BIND DEVICE
4
the IMEI manually to bind the device
Attention:
When reading this user manual, you will notice that we have used "+" and "space"
between some words;"+" between two words means they should be written
together as one word and "space" between two words means you should leave one
character space between two words.
5
6. GPRS CONFIGURATION FOR LIVE REAL-TIME
TRACKING
Set APN, Account user name and password to login web platform
Usually, the device can automatically recognize and select the APN, user name and password
of GPRS settings. If the device cannot connect to the web platform, then you need to use the
mobile phone text message to configure the settings according to following steps.
In the most countries, the user name and password of GPRS are not necessary;
therefore, you can ignore this step if it is not necessary for your local network.
For those countries requiring user name and password, please configure as
following:
SMS command: up+password+space+user+space+password
Tracker response: user, password ok!
Example: up123456 Jonnes 666666
Note: 123456 means the password of the device, Jonnes means the user name
ofgprs, and 666666 means password of gprs
Tracker connects to www.baanooliot.com 8090 by default. If you need to connect to another domain name,
please configure it.
SMS command: dns+password+space+DNS domain name+space+port
Tracker response: dns success!
Example : dns123456 www.baanooliot.com 8090
Note:
If you want to configure IP instead of DNS, then please send SMS command:
“adminip+password+space+IP+space+port”
6
6.4 GPRS MODE
7. FUNCTION DETAILS
The following setting functions can be set through the APP or web version
7.2 Authorization
7
7.3 Single Tracking
7.3.1 If there aren’t any authorized numbers set-up, it will reply all calls with a location
report; if there are authorized numbers set-up, then it will not respond when an
unauthorized number calls it。
7.3.2 If you call it from authorized phone number, it will hang up and report a real-time
location as below:
When it lost fix to satellites, the message will include the last known GPS position and a
LAC code of the updated position as well。
7.3.3 SMS Command:position+password,The function is the same as 7.3.2
8
200 meters, it will reported, and only report 5 times.005n is means limited to 5 times of positioning, * **n
means Unlimited times.
Note: The time must be represented by 3 Arabic numerals, the distance must be represented by 4
Arabic numerals, d represents the distance, the distance unit is meters, and the minimum static interval is
set to 30 minutes (s: seconds, m: minutes, h: hours)
The above command means: no sleep mode (GPRS is always online), It will update a position at
30min interval when moving, and update a position at 200 meters interval when motionless, and
only 5 times are updated, 005n means 5 times, ***n means unlimited times.
Note: The time must be represented by 3 Arabic numerals, and the moving distance must be
represented by 4 Arabic numerals. d represents the distance, the distance unit is meters, and the time
7.5.1 It will update positions automatically to web platform when the vehicle changes
driving direction over a preset angle value to make its trace following the actual road
and seem better on the map. This function is only available in GPRS mode.
7.5.2 SMS command: angle+password+space+angle value,Tracker response: angle ok
7.5.3 Note: The angle value must be 3 Arabic digits, and the default value is 30 degree.
9
7.6 Location based service (LBS) / Cell-ID tracking
If the tracker cannot establish a solid GPS Fix, it will calculate its location using Cell-ID
GSM locating. In SMS mode, location reports will include the GPS coordinates of the last
known positions as well as a LAC code which is the current latest position. If in GPRS mode,
tracker will automatically switch to tracking by LBS. and locate directly on the platform map
with LBS positioning prompts. The base station positioning information has an error with the
actual position, and the error range is related to the strength of the GSM signal.
Note: This function can be used normally in most areas according to GSM signal
conditions, but may not be available in some areas.
This function assumes that your GSM network provider has the option where you
can check your SIM card’s balance by sending a SMS message to a specified
number, which is 10086 in this example of China Mobile.
10
7.9 ACC ON/OFF Alert
11
7.11 Configure times of alarm SMS
The times of the message of a continuous alarm can be configured. 3 times messages by
default.
SMS command: xtime+password+times value
Tracker response: xtime ok!
Note: The times value must be 3 digits.
Example: xtime123456 005 (It means to send messages 5 times.)
7.12 Alarms
12
This feature is deactivated by default, tracker will send SMS notification “ No
gps+latitude& longitude of the last know position.”to authorized numbers if lost fix to
GPS satellites.
SMS command to activate: gpssignal +password+space+on
Tracker response: gpssignal on ok
Example: gpssignal123456 on
SMS command to deactivate: gpssignal +password+space+off
Tracker response: gpssignal off ok
Example: gpssignal123456 off
Press key on the remote control, tracker will send SMS notification "Help
13
reply "move ok!". Once the device is out of range, the device will reply the message "move +
latitude and longitude" to the authorized number. (The default distance of the device is 200
meters,)
Cancel the setting: Send SMS "nomove+password" to cancel this function setting.
7.12.7 Over speed alarm
Setting: Send SMS command "speed+password+space+080" to the device (assuming the
speed is 80km/h), then the device will reply "speed ok!". When the device runs over 80km/h,
the device will send the message " speed+080!+latitude and longitude" to the authorization
number. Over speed alarm SMS mode only sends a text message once within 3 minutes; the
siren sounds for one second when speeding.
Cancel the setting: Send SMS "nospeed+password" to cancel this function setting.
Note: The recommended speed should not be less than 30km/h.If the speed is set lower
than this you may get a false alarm due to GPS inaccuracy.
7.14 Arming
14
7.14.2 Arming with remote controller (For D model)
not sound, but an alarm text message will be sent to the authorized number.
7.15.2 Silent arming with remote controller(For D model)
Press key for 0.5 second in disarm state,the siren will beep onetime, the vehicle enters
the silent arming state. After the alarm is triggered, the siren does not operate, but an
alarm text message will be sent to the authorized number.
7.16 Disarming
Press for 0.5 second, tracker will enter into disarming state, siren beeps two times.
15
still on, then the siren will beep for another 20 seconds with 20 seconds pause,disarming to
quite the alarm.
At the same time app receive alarm message.
7.17.2 Acceleration Sensor Alarm
7.17.2.1 There is a built-in three axis acceleration sensor in the tracker to detect the
movement, tilt and shock when in arming state and tracker will send “Sensor alarm +
latitude / longitude” to authorized numbers, and only one message in 3 minutes when
tracker works in SMS mode. Siren will beep for 5 seconds for the first trigger and
second trigger, and then beep 10 seconds for another trigger, at the same time app
receive alarm message ,disarming to quit the alarm
7.17.2.2 Sensor’s sensitivity configuration
There are three different levels:
First level: Alarm will be triggered by slight vibration.
SMS command: sensitivity+password+space+1
Tracker response: sensitivity ok
Example: sensitivity123456 1
Second level: Alarm will be triggered by medium vibration.
SMS command: sensitivity+password+space+2
Tracker response: sensitivity ok
Example: sensitivity123456 2
Third level: Alarm will be triggered by severe vibration.
SMS command: sensitivity+password+space+3
Tracker response: sensitivity ok
Example: sensitivity123456 3
16
7.19 Check IMEI
Tracker works in the local time zone by default. If you find that the time zone is incorrect,
you can configure the time zone
SMS command: time+space+zone+password+space+time zone value
Tracker responds: time ok
Example: time zone123456 8
SMS command to switch to TCP mode: GPRS+password,0,0 (TCP mode is the default one)
SMS command to switch to UDP mode: GPRS+password,1,1
Tracker response: GPRS OK!
Example: GPRS123456,0,0
GPRS123456,1,1
Switch to SMS mode will disconnect the GPRS connection for live tracking.
SMS command: SMS+password
Tracker response: SMS OK! ( It means it has been switched to SMS mode.)
Example: SMS123456
17
7.24 Configure SMS monitoring center number
The default heartbeat interval to keep GPRS connection alive is 100 seconds; you can change
it if necessary, but please be kindly informed that if the time interval is too long, it may cause
GPRS disconnection.
SMS command: heartbeat+password+space+time interval
Tracker response: heartbeat ok
Example: heartbeat123456 120
7.26 Initialization
If the tracker cannot work properly, you can send command to initialize it to return to default
factory settings.
SMS command: begin+password
Tracker response: begin ok
Example: begin123456
18
8. CAUTIONS
Please be sure to follow when using:
1. Keep the tracker used in a dry environment. The humid environment can easily damage
internal circuits.
2. Please do not put it in a dusty environment.
3. Do not put the tracker in overheated or overcooled places.
4. Handle carefully. Don’t vibrate or shake it violently.
5. Please clean with a dry cloth, do not use chemicals and detergents.
6. Please do not paint the device; this may lead to internal circuit failure.
7. Do not disassemble the device.
8. Please read the user manual carefully before installation and operation, and understand
voltage range. Otherwise, it won’t work properly or damage the tracker.
9. TROUBLESHOOTING
Faults Solution
19
No response for a 1. Did you have set up the authorized phone number?
call/No alarm 2. If authorized number exists, did you make the call from an
notification authorized phone number?
message 3. The format of the phone number is incorrect.
Remote control
Turn off tracker, and turn it on to program the remote control again.
cannot be used
20