EM ICA HM131 131R (V2) - v2.0
EM ICA HM131 131R (V2) - v2.0
264 Full-HD
Fixed Dome IP Camera
► ICA-HM131/ICA-HM131R
-1-
Copyright
Copyright (C) 2012 PLANET Technology Corp. All rights reserved.
The products and programs described in this User’s Manual are licensed products of PLANET Technology, This
User’s Manual contains proprietary information protected by copyright, and this User’s Manual and all
No part of this User’s Manual may be copied, photocopied, reproduced, translated, or reduced to any electronic
medium or machine-readable form by any means by electronic or mechanical. Including photocopying, recording,
or information storage and retrieval systems, for any purpose other than the purchaser's personal use, and without
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in all environments and applications,
and makes no warranty and representation, either implied or expressed, with respect to the quality, performance,
PLANET has made every effort to ensure that this User’s Manual is accurate; PLANET disclaims liability for any
Information in this User’s Manual is subject to change without notice and does not represent a commitment on the
part of PLANET. PLANET assumes no responsibility for any inaccuracies that may be contained in this User’s
Manual. PLANET makes no commitment to update or keep current the information in this User’s Manual, and
reserves the right to make improvements to this User’s Manual and/or to the products described in this User’s
If you find information in this manual that is incorrect, misleading, or incomplete, we would appreciate your
CE mark Warning
The is a class B device, In a domestic environment, this product may cause radio interference, in which case the
WEEE Warning
To avoid the potential effects on the environment and human health as a result of the presence of
hazardous substances in electrical and electronic equipment, end users of electrical and electronic
equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of
WEEE as unsorted municipal waste and have to collect such WEEE separately.
Trademarks
The PLANET logo is a trademark of PLANET Technology. This documentation may refer to numerous hardware
and software products by their trade names. In most, if not all cases, their respective companies claim these
-2-
Revision
User’s Manual for PLANET H.264 Full-HD Fixed Dome IP Camera
-3-
TABLE OF CONTENTS
Chapter 1 Introduction..............................................................................................6
Overview ........................................................................................................................................ 6
Package Content........................................................................................................................... 7
Physical Details ............................................................................................................................ 7
Top View................................................................................................................................ 7
Side View .............................................................................................................................. 8
Chapter 2 Preparations for IP Cameam Setup ........................................................9
Physical Installation Requirement .............................................................................................. 9
2.1 System Requirements ............................................................................................................ 9
2.2 Ethernet Connection .............................................................................................................. 9
2.3 PoE Connection ...................................................................................................................... 9
Chapter 3 Accessing Camera................................................................................. 11
3.1 Device Search Software Setup .............................................................................................11
3.2 Device Search ....................................................................................................................... 12
3.3 Example of Changing IP Camera’s Network Property ...................................................... 13
3.4 Installing DC Viewer Software Online................................................................................. 15
3.5 Administrator / User Privileges ........................................................................................... 16
3.6 Lens Adjustment................................................................................................................... 16
Chapter 4 Configuration & Operation....................................................................18
4.1 Browser-based Viewer Introduction ................................................................................... 18
4.2 Home Page.......................................................................................................................... 19
4.3 System Related Settings ................................................................................................... 21
4.3.1 Host Name and System Time Setting ............................................................. 21
4.3.2 Security.............................................................................................................. 22
4.3.3 Network.............................................................................................................. 30
4.3.4 DDNS.................................................................................................................. 37
4.3.5 Mail..................................................................................................................... 38
4.3.6 FTP ..................................................................................................................... 38
4.3.7 HTTP .................................................................................................................. 39
4.3.8 Motion Detection............................................................................................... 40
4.3.9 Network failure detection................................................................................. 43
4.3.10 Tampering Alarm............................................................................................... 45
4.3.11 Storage Management (Local Recording)........................................................ 49
4.3.12 Recording (Local Recording) .......................................................................... 51
4.3.13 File Locatioin..................................................................................................... 52
4.3.14 View information............................................................................................... 52
4.3.15 Factory Default.................................................................................................. 54
4.3.16 Software Version............................................................................................... 56
-4-
4.3.17 Software Upgrade ............................................................................................. 57
4.3.18 Maintenance ...................................................................................................... 60
4.4 Video and Audio Streaming Settings.................................................................................. 61
4.4.1 Video format (Video Resolution/ Video Deinterlace)..................................... 61
4.4.2 Video Compression .......................................................................................... 63
4.4.3 Video ROI........................................................................................................... 64
4.4.4 Video OCX Protocol.......................................................................................... 65
4.4.5 Video Frame Rate ............................................................................................. 66
4.4.6 Video Mask ........................................................................................................ 67
4.4.7 Audio Mode and Bit Rate Settings.................................................................. 67
4.5 Camera Settings ................................................................................................................... 69
4.5.1 Exposure Setting .............................................................................................. 69
4.5.2 White Balance Setting...................................................................................... 70
4.5.3 Brightness Setting............................................................................................ 71
4.5.4 Backlight............................................................................................................ 72
4.5.5 Digital Zoom ...................................................................................................... 72
4.5.6 WDR Function ................................................................................................... 72
4.5.7 Noise Reduction ............................................................................................... 73
4.5.8 TV System Setup .............................................................................................. 73
4.6 Logout ................................................................................................................................. 74
Appendix A: IP Camera Specifications..................................................................................... 75
Appendix B: Internet Security Settings.................................................................................... 76
Appendix C: DC Viewer Download Procedure......................................................................... 79
Appendix D: Frequently Asked Questions............................................................................... 81
-5-
Chapter 1
Introduction
1
Overview
PLANET has announced a H.264 Full-HD Fixed Dome IP camera, ICA-HM131/131R, for meeting the
feedback from worldwide market. The ICA-HM131 series support Full HD recording for high quality image.
Integrated the next generation video compression technology – H.264, the ICA-HM131 series can compress
the video size to smaller one for users to transfer the Mega-Pixel image on Internet easily.
The ICA-HM131 series IP Cameras are innovatively designed for quick and easy installation in drop ceilings
without concerning the outlet / socket locations. Power over Ethernet (IEEE 802.3af) supplies power to the
cameras via the network, eliminating the need for power cables and reducing installation costs.
Multi-profile stands for video stream simultaneously. The ICA-HM131 series can deliver clear image with dual
H.264/M-JPEG stream video up to 1080p (1920 x 1080 pixels). The IP Cameras use progressive scan,
providing full resolution images of moving objects without distortion, in 30 frames per second, perfect for
critical areas such as entrances or checkouts that need to be monitored in greater detail.
The ICA-HM131 series can be managed by PLANET Cam Viewer Three, the professional management
software for multi-camera video surveillance application, to provide monitoring, recording and event
management functions. The Cam Viewer Three enables you to setup a comprehensive and effective
surveillance system quickly and easily. With the ICA-HM131 series managed by the Cam Viewer Three, it
provides an enhanced professional security environment to protect your property and life.
Product Features
Camera
• 1/2.7” progressive CMOS
• Dual video stream : H.264 and M-JPEG video compression simultaneously
• Supports 1080p Full-HD resolution (1920 x 1080 pixels)
• Compliant with IEEE 802.3af PoE interface
• Supports ONVIF Standard to Simplify Integration and Enhance Interoperability
Management
-6-
• Easy configuration and management via Windows-Based utility or web interface
• Cam Viewer Three - Central management software supported
• DDNS, PPPoE and FTP uploading supports more alternatives in surveillance network
Feature
• Motion Detection feature can monitor any suspicious movement in specific area
• Wide Dynamic Range (WDR) / 3D Noise Reduction (3DNR) function support
• Planet DDNS function support
Package Content
The contents of your product should contain the following items:
IP Camera
Quick installation guide
User’s manual CD
Accessories Kit
Physical Details
Top View
-7-
4. Tilt Fixed
1. Lens
Screw
2. Reset Button
5. Microphone
3. Focus Fixed
Screw
Side View
2. RJ-45 LAN
Socket
1. Micro-SD
Card slot
-8-
Preparations for IP Cameam Setup
Chapter 2
2
Physical Installation Requirement
The notices and introduction on system installation will be described particularly in this chapter. Please follow
the description to operate the unit.
In order to prevent the unit from data loss and system damage that caused by a sudden power fluctuation, use
of an Uninterruptible Power Supply (UPS) is highly recommended.
-9-
1. The RJ-45 interface only accept IEEE802.3af PSE (Power Source
Equipmetns) Any non-standard or passive POE is not allowed to
Note power the system and will damage the IP Camera permanently.
2. You can also consult your local dealer for 802.3af POE PSE devices
such as single port injector for single point installation. Or, for mass
installation, a Injector Hub for the network that already existed with
Ethernet Switches or POE Switch all can be deployed.
- 10 -
Accessing Camera
Chapter 3
3
For initial access to the IP Camera, users can search the camera through the installer program:
DeviceSearch.exe, which can be found in “DeviceSearch” folder in the supplied CD.
Step 2: The security alert window will pop up. Click “Run” to continue.
- 11 -
3.2 Device Search
Step 3: Click “Device Search” again, and all the finding IP devices will be listed in the page, as shown
in the figure below. The IP Camera’s default IP address is: 192.168.0.20.
Step 4: Double click or right click and select “Browse” to access the camera directly via web browser.
Step 5: Then the prompt window of request for entering default username and password (as shown
below) will appear for logging in to the IP Camera.
- 12 -
The default login ID and password for the Administrator are:
Login ID Password
admin admin
NOTE: It is strongly advised that administrator’s password be altered for the security
concerns. Refer to section 4.3.2 Security for further details.
Additionally, users can change the IP Camera’s network property, either DHCP or Static IP, directly in
the device finding list. Refer to the following section for changing the IP Camera’s network property.
Step 1: In the finding device list, click on the IP Camera that you would like to change its network
property. On the selected item, right click and select “Network Setup.” Meanwhile, record the IP
Camera’s MAC address, for future identification.
Step 2: The “Network Setup” page will come out. Select “DHCP,” and press “Apply” button down the
page.
- 13 -
Step 3: Click “OK” on the Note of setting change. Wait for one minute to re-search the IP Camera.
Step 4: Click the “Device Search” button to search all the devices. Then select the IP Camera with the
correct MAC address. Double click on the IP Camera, and the login window will come out.
- 14 -
3.4 Installing DC Viewer Software Online
For the initial access to the IP Camera, a client program, DC Viewer, will be automatically installed to
your PC when connecting to the IP Camera.
If the Web browser doesn’t allow DC Viewer installation, please check the Internet security settings or
ActiveX controls and plug-ins settings (see Appendix B: Internet Security Settings) to continue the
process.
The Information Bar (just below the URL bar) may come out and ask for permission to install the
ActiveX Control for displaying video in browser (see the figure below). Right click on the Information Bar
and select “Install ActiveX Control…” to allow the installation.
Then the security warning window will pop up. Click “Install” to carry on software installation.
Click “Finish” to close the DC Viewer window when download is finished. For the detailed software
download procedure, please refer to Appendix C: DC Viewer Download Procedure.
Once login to the IP Camera, users will see the Home page as shown below:
- 15 -
3.5 Administrator / User Privileges
“Administrator” represents the person who can configure the IP Camera and authorize users access to
the camera; “User” refers to whoever has access to the camera with limited authority, i.e. entering
Home and Camera setting pages.
- 16 -
Step 2: Loosen the focus fixed screw, and rotate the lens counter-/clockwise to adjust focus; loosen the
tilt fixed screw, and adjust the camera’s tilt angle.
- 17 -
Configuration & Operation
Chapter 4
4
The IP Camera is provided with a user-friendly browser-based configuration interface, and a free
bundled CV3L (Cam Viewer Three Lite) for record and playback video. In this chapter, information
about main page introduction, system related settings and camera settings will be described in detail.
There are five tabs: Home, System, Streaming, Camera and Logout on the top of the viewer window.
- 18 -
Home
Users can monitor live video of the targeted area.
System setting
The administrator can set host name, system time, root password, network related settings, etc. Further
details will be interpreted in section 4.3 System Related Settings.
Streaming setting
The administrator can modify video resolution and rotate type and select audio compression mode in
this page.
Camera setting
Users can adjust various camera parameters, including <Exposure>, <White Balance>, <Brightness>,
<Sharpness>, <Contrast> and <Digital Zoom>.
Logout
Click on the tab to re-login the IP Camera with another username and password.
- 19 -
Digital Zoom Control
In the full screen mode, users can implement digital zoom by right clicking the mouse, rotating the
mouse wheel (for zoom in/out) and dragging the mouse into any direction.
Snapshot
Press the button, and the JPEG snapshots will automatically be saved in the appointed place.
The default place of saving snapshots is: C:\.
Talk
Talk function allows the local site talks to the remote site. Please refer to section 4.3.2 Security: Add
user > Talk/Listen for further details. This function is only open to “User” who has been granted this
privilege by the Administrator.
Speaker
Press the button to mute/activate the audio.
Recording
Press the button to save video recordings from the Live View to the specified location.
- 20 -
4.3 System Related Settings
The figure below shows all categories under the “System” tab. Each category in the left column will be
explained in the following sections.
Host Name
The name is for camera identification. If Motion Detection function is enabled and is set to send alarm
message by Mail/FTP, the host name entered here will display in the alarm message.
Time Zone
Select the time zone you are in from the drop-down menu.
Manual
The Administrator can set video date, time and day manually. Entry format should be identical with that
shown next to the enter fields.
4.3.2 Security
Click the category: <Security>, and the page is shown as the figure below.
4.3.2.1 User
- 22 -
Root password
Change the administrator’s password by inputting the new password in both text boxes. The input
characters/numbers will be displayed as dots for security purposes. After clicking <Save>, the web
browser will ask the Administrator for the new password for access. The maximum length of the
password is 14 digits.
NOTE: The following characters are valid: A-Z, a-z, 0-9, !#$%&’-.@^_~.
Add user
Type the new user's name and password and click <Add> to add the new user. Both user name and
password can be up to 16 characters. The new user will be displayed in the user name list. There is a
maximum of twenty user accounts. Each user can be assigned the privileges of “Camera control”
and/or “Listen”.
• I/O access
This item supports fundamental functions that enable users to view video when accessing to the
camera.
• Camera control
This item allows the appointed User to change camera parameters on the Camera Setting page.
• Listen
Listen functions allow the administrator hear the sounds in the local site (PC site).
Manage User
Delete user
To delete a user, pull down the user list, and select the user name you wish to delete. Then click
<Delete> to remove it.
Edit user
Pull down the user list and select a user name. Click <Edit> to edit the user’s password and privilege.
NOTE: It is required to enter the User password as well as select the function open to the
user. When finished, click <Save> to modify the account authority.
- 23 -
4.3.2.2 HTTPS
<HTTPS> allows secure connections between the IP Camera and web browser using <Secure
Socket Layer (SSL)> or <Transport Layer Security (TLS)>, which ensure camera settings or
Username/ Password info from snooping. It is required to install a self-signed certificate or a
CA-signed certificate for implementing <HTTPS>.
- 24 -
To use HTTPS on the IP Camera, a HTTPS certificate must be installed. The HTTPS certificate can
be obtained by either creating and sending a certificate request to a Certificate Authority (CA) or
creating a self-signed HTTPS certificate, as described below.
Click on <Create> button under “Create self-signed certificate” and provide the requested
information to install a self-signed certificate for the IP Camera. Please refer to the last part of this
section: Provide the Certificate Information for more details.
The self-signed certificate does not provide the same high level of security as when using
a CA-issued certificate.
Note
- 25 -
Provide the request information in the create dialog. Please refer to the following Provide the
Certificate Information for more details.
When the request is complete, the subject of the Created Request will be shown in the field. Click
on <Properties> below the Subject field, copy the PEM-formatted request and send it to your
selected CA.
When the signed certificate is returned, install it by uploading the signed certificate.
Country √ √
State or Province √ √
Locality √ √
Organization √ √
Organizational Unit √ √
Common Name √ √
Valid Day √ -
• Country
Enter a two-letter combination code to indicate the country the certificate will be used in. For instance,
type in “US” to indicate United States.
• State or province
Enter the local administrative region.
- 26 -
• Locality
Enter other geographical information.
• Organization
Enter the name of the organization to which the entity identified in “Common Name” belongs.
• Organization Unit
Enter the name of the organizational unit to which the entity identified in “Common Name” belongs.
• Common Name
Indicate the name of the person or other entity that the certificate identifies (often used to identify the
website).
• Valid days
Enter the period in days (1~9999) to indicate the valid period of certificate. Click on <OK> to save the
Certificate Information after complete.
- 27 -
4.3.2.3 IP Filter
The IP Filter setting can be found under this path: System> Security> IP Filter.
Using the IP filter, access to the IP Camera can be restricted by denying/allowing specific IP addresses.
z Enable IP Filter
Check the box to enable the IP Filter function. Once enabled, the listed IP addresses (IPv4) will be
allowed/ denied access to the IP Camera.
Select <Allow> or <Deny> from the drop-down list and click on the <Apply> button to determine the IP
Filter behavior.
z Add/ Delete IP Address
Input the IP address and click on the <Add> button to add a new filtered address.
The Filtered IP Addresses list box shows the currently configured IP addresses. Up to 256 IP address
entries may be specified.
To remove an IP address from the list, please select the IP and then click the <Delete> button.
- 28 -
4.3.2.4 IEEE 802.1X
The IEEE 802.1X setting can be found under this path: System> Security> IEEE 802.1X.
Users need to contact with the network administrator for gaining certificates, user IDs and passwords
CA Certificate
The CA certificate is created by the Certification Authority for the purpose of validating itself. Upload the
certificate for checking the server’s identity.
Settings
• Identity
Enter the user identity associated with the certificate. Up to 16 characters can be used.
- 29 -
• Private Key Password
Enter the password (maximum 16 characters) for your user identity.
4.3.3 Network
Click <Network> in the left column, and the page will display as shown below.
4.3.3.1 Basic
Users can choose to use fixed IP address or dynamic (DHCP) IP address. The following is descriptions
for the two ways of setting IP address.
- 30 -
Get IP address automatically (DHCP)
The camera’s default setting is “Use fixed IP address”. Please refer to the previous section Chapter 3.
Accessing Camera for logging in with the default IP address.
If select “Get IP address automatically”, after the IP Camera restarts, users can search it through the
installer program: DeviceSearch.exe, which can be found in “DeviceSearch” folder in the supplied CD.
NOTE: Please make the record of the IP Camera’s MAC address, which can be found in
the label of the camera, for identification in the future.
When using static IP address to login to the IP Camera, users can access it either through
“DeviceSearch” software (see Chapter 3. Accessing Camera) or input the IP address in the URL bar
- 31 -
and press “Enter”.
General
• IP address
This is necessary for network identification.
• Subnet mask
It is used to determine if the destination is in the same subnet. The default value is “255.255.255.0”.
• Default gateway
This is the gateway used to forward frames to destinations in different subnet. Invalid gateway setting
will fail the transmission to destinations in different subnet.
• Primary DNS
Primary DNS is the primary domain name server that translates hostnames into IP addresses.
• Secondary DNS
Secondary DNS is a secondary domain name server that backups the primary DNS.
Advanced
• RTSP port
RTSP port could be set from 1 to 65535. (Normal Setting Port: 554, 1024 ~65535)
• HTTPS port
The default setting of HTTPS Port is 443; the setting range is from 1024 to 65535.
- 32 -
NOTE: Be aware to choose the different port from the one set for the web server port.
4.3.3.2 QoS
The QoS (Quality of Service) setting can be found under this path: System> Network> QoS.
QoS allows providing differentiated service levels for different types of traffic packets, which guarantees
delivery of priority services especially when network congestion occurs. Adapting the Differentiated
Services (DiffServ) model, traffic flows are classified and marked with DSCP (DiffServ Codepoint)
values, and thus receive the corresponding forwarding treatment from DiffServ capable routers.
DSCP Settings
The DSCP value range is from 0 to 63. The default DSCP value is 0, which means DSCP is disabled.
The IP Camera uses the following QoS Classes: Video, Audio and Management.
- 33 -
• Video DSCP
The class consists of applications such as MJPEG over HTTP, RTP/RTSP and RTSP/HTTP.
• Audio DSCP
This setting is only available for the IP Cameras that support audio.
• Management DSCP
The class consists of HTTP traffic: Web browsing.
NOTE: To enable this function, please make sure the switches/ routers in the network
support QoS.
4.3.3.3 SNMP
The SNMP (Simple Network Management Protocol) setting can be found under this path: System>
Network> SNMP.
- 34 -
With Simple Network Management Protocol (SNMP) support, the IP Camera can be monitored and
managed remotely by the network management system.
SNMP v1/ v2
• Enable SNMP v1/ v2
Select the version of SNMP to use by checking the box.
• Read Community
Specify the community name that has read-only access to all supported SNMP objects. The
default value is “public”.
• Write Community
Specify the community name that has read/write access to all supported SNMP objects (except
read-only objects). The default value is “write”.
• Enable Traps
Check the box to activate trap reporting.
• Trap address
Enter the IP address of the management server.
• Trap community
Enter the community to use when sending a trap message to the management system.
Trap Option
• Warm Start
A Warm Start SNMP trap signifies that the SNMP device, i.e. IP Camera, performs software
reload.
4.3.3.4 UPnP
The UPnP setting can be found under this path: System> Network> UPnP.
- 35 -
UPnP Setting
z Enable UPnP
When the UPnP is enabled, whenever the IP Camera is presented to the LAN, the icon of the
connected IP Cameras will appear in My Network Places to allow for direct access.
NOTE: To enable this function, please make sure the UPnP component is installed on your
computer. Please refer to Install UPnP components for UPnP component installation
procedure.
To enable this function, please make sure that your router supports UPnP
and it is activated.
Note
• Friendly name
Set the name for the IP Camera for identity.
- 36 -
4.3.4 DDNS
Dynamic Domain Name System (DDNS) allows a host name to be constantly synchronized with a
dynamic IP address. In other words, it allows those using a dynamic IP address to be associated to a
static domain name so others can connect to it by name.
Enable DDNS
Check the item to enable DDNS.
Provider
Select one DDNS host from the provider list.
Host name
Enter the registered domain name in the field.
Example : planetddnstest01
Username/
Enter the username required by the DDNS provider for authentication.
Example : planetddnstest01
Password
- 37 -
Enter the password required by the DDNS provider for authentication.
Example : planetddnstest01
If you want to use Planet DDNS please aply form the Planet DDNS page
http://www.planetddns.com/index.php
Note
4.3.5 Mail
The Administrator can send an e-mail via Simple Mail Transfer Protocol (SMTP) when motion is
detected. SMTP is a protocol for sending e-mail messages between servers. SMTP is a relatively
simple, text-based protocol, where one or more recipients of a message are specified and the message
text is transferred. The configuration page is shown as follows:
Two sets of SMTP can be configured. Each set includes SMTP Server, Account Name, Password and
E-mail Address settings. For SMTP server, contact your network service provider for more specific
information.
4.3.6 FTP
The Administrator can set as sending alarm message to a specific File Transfer Protocol (FTP) site
when motion is detected. Users can assign alarm message to up to two FTP sites. The FTP setting
page is shown below. Enter the FTP details, which include server, server port, user name, password
and remote folder, in the fields. Press “Save” when finished.
- 38 -
4.3.7 HTTP
The HTTP setting can be found under this path: System> HTTP.
- 39 -
A HTTP Notification server can listen for notification messages from IP Cameras by triggered
events. Enter the HTTP details, which include server name (for instance,
http://192.168.0.1/admin.php), user name, and password in the fields. <Alarm> triggered and
<Motion Detection> notifications can be sent to the specified HTTP server.
Click on <Save> when finished.
In the Motion Detection setting page, there is a frame (Motion Detection Window) displayed on the
Live View Pane. The Motion Detection Window is for defining the motion detection area. To change the
size of the Motion Detection Window, move the mouse cursor to the edge of the frame and draw it
outward/inward. Moving the mouse to the center of the frame can shift the frame to the intended
location.
Up 10 Motion Detection Windows can be set. Press the “add” button under the Live View Pane to add a
Motion Detection Window. To cancel a Motion Detection Window, move the mouse cursor to the
selected Window, and click on the “delete” button.
If Motion Detection function is activated, the pop-off window (Motion) with indication of motion will be
shown.
- 40 -
When motion is detected, the signals will be displayed on the Motion window as shown below.
Motion Detection
You will be able to turn on/off Motion Detection in System section. Default setting is Off.
File Name
The uploaded image’s filename format can be set in this section. Please select the one that meets your
requirements.
Save
Click the Save button to save all the Motion Detection settings mentioned above.
The Tampering setting can be found under this path: System> Network failure detection
- 43 -
Being capable of implementing local recording (through Micro SD card) when network failure happens,
the IP Camera could be a backup recording device for the surveillance system.
Detection Switch
You will be able to turn on/off Network Failure Detection in System section.
Default setting is Off.
Detection Type
Input the IP device address and the period of ping time to ping. The ping time
setting range is from 1 to 99 minutes.
Pre-trigger buffer recording function allows users to check what happened to cause the trigger. The
pre-trigger buffer time range is from 1 to 3 seconds. Select <Upload for __ sec> to set the recording
- 44 -
duration after alarm is triggered. The setting range is from 1 to 99999 seconds. Select <Upload during
the trigger active> to record the triggered video until the trigger is off.
Please make sure the local recording (with Micro SD/ SDHC card) is activated so that this
function can be implemented. Refer to Recording for further details.
Note
Make sure SMTP or FTP configuration has been completed. Refer to Mail and FTP for
further details.
Note
Tampering Alarm function helps the IP Camera against tampering such as deliberate redirection,
blocking, paint spray, and lens cover, etc through video analysis and reaction to such events by sending
out notifications or uploading snapshots to the specified destination(s).
Detection of camera tampering is achieved by measuring the differences between the older frames of
video (which are stored in buffers) and more recent frames.
Tampering Alarm
Users are able to turn on/off Tampering Alarm function in Tampering Alarm setting page. The default
setting is Off.
- 45 -
Tampering Duration
Minimum Tampering Duration is the time for video analysis to determine whether camera tampering
has occurred. Minimum Duration could also be interpreted as defining the Tampering threshold; longer
duration represents higher threshold. Settable Tampering Duration time range is from 10 to 3600
seconds. The Default value is 20 seconds.
Pre-trigger buffer recording function allows users to check what happened to cause the trigger. The
pre-trigger buffer time range is from 1 to 3 seconds.
Select <Upload for __ sec> to set the recording duration after tampering occurs. The setting range is
from 1 to 99999 seconds.
Select <Upload during the trigger active> to record the triggered video until the trigger is off.
NOTE: Please make sure the local recording (with Micro SD/ SDHC card) is activated so that
this function can be implemented. Refer to Recording for further details.
<Pre-trigger buffer> function allows users to check what happened to cause the trigger. The
<Pre-trigger buffer> frame rate could be pre-determined.
- 46 -
On the other hand, <Post-trigger buffer> is for users to upload certain amount of images after tampering
is triggered.
Check the box <Continue image upload> to upload the triggered images during certain time or keep
uploading until the trigger is off. Select <Upload for __sec> and enter the duration in the blank. The
images of the duration will be uploaded to FTP when tampering is triggered. The setting range is from 1
to 9999 seconds. Select <Upload during the trigger active> to make the images keep being upload to
FTP during the trigger active until the tampering stops. Set the Image frequency as the upload frame
rate. The setting range is from 1 frame to 15 frames.
NOTE: Make sure FTP configuration has been completed. Refer to FTP for further details.
<Pre-trigger buffer> function allows users to check what happened to cause the trigger. The
<Pre-trigger buffer> frame rate could be pre-determined.
On the other hand, <Post-trigger buffer> is for users to upload certain amount of images after tampering
occurs.
Check the box <Continue image upload> to upload the triggered images during certain time or keep
uploading until the trigger is off. Select <Upload for __sec> and enter the duration in the blank. The
images of the duration will be uploading by E-mail when tampering is triggered. The setting range is
from 1 to 9999 seconds. Select <Upload during the trigger active> to make the images keep being
upload to E-mail during the trigger active until tampering stops. Set the Image frequency as the upload
frame rate. The setting range is from 1 frame to 20 frames.
NOTE: Make sure SMTP configuration has been completed. Refer to Mail for further details.
For instance, if the custom parameter is set as” action=1&group=2”, and the HTTP server name is”
http://192.168.0.1/admin.php”, the notification will be sent to HTTP server as”
http://192.168.0.1/admin.php? action=1&group=2” when alarm is triggered.
- 47 -
File Name
Enter a file name in the blank, ex. image.jpg. The uploaded image’s file name format can be set in this
section. Please select the one that meets your requirements.
The file name suffix will end at the number being set. For example, if the setting is up to “10,” the file
name will start from 00, end at 10, and then start all over again.
z Overwrite
The original image in the FTP site will be overwritten by the new uploaded file with a static filename.
Save
Click on the <Save> button to save all the Tampering Alarm settings mentioned above.
- 48 -
4.3.11 Storage Management (Local Recording)
The Storage Management setting can be found under this path: System> Storage Management.
- 49 -
Users can implement local recording to the Micro SD/SDHC card up to 32GB. This page shows the
capacity information of the Micro SD card and a recording list with all the recording files saved on the
memory card. Users can also format the SD card and implement automatic recording cleanup through
the setting page.
To implement Micro SD card recording, please go to the <Recording> page (refer to the section
Recording) for activation.
Please format the Micro SD/SDHC card when using for the first time. Formatting will also
be required when a memory card already being used on one camera and later transferred
Note to another camera with different software platform.
Device information
When users insert the Micro SD/SDHC card, the card information such as the memory capacity and
status will be shown at Device Information section.
When the memory card is successfully installed, the memory card status shall be shown at <Device
information> section in the Storage Management page.
Device setting
Click on the <Format> button to format the memory card.
Recording List
Each video file on the Micro SD/SDHC card will be listed in the Recording list. The maximum file size is
60 MB/per file.
When the recording mode is set as <Always> (consecutive recording) and the Micro SD/ SDHC card
recording is also allowed to be enabled by events triggered, once events occur, the system will
immediately implement events recording to the memory card. Then the IP Camera will return to the
regular recording mode after events recording.
• Remove
To remove a file, select the file first, and then click on the <Remove> button.
• Sort
Click on the <Sort> button, and the files in the Recording list will be listed in name and date order.
- 50 -
The capital letter A/M/R appears in the very beginning of name denotes the sort of the
recording: A stands for Alarm; M stands for Motion; R stands for regular recording.
Note
• Download
To open/download a video clip, select the file first, and then click on the <download> button below the
Recording list field. The selected file window will pop up. Click on the AVI file to directly play the video in
the player or download it to a specified location.
In the Recording setting page, users can specify the recording schedule that fits the present
surveillance requirement.
Please click on the <Save> button for confirming the schedule mode.
- 51 -
Terminating Micro SD/SDHC Card Recording
Select <Disable> to terminate the recording function.
Please make sure the selected file path contains valid characters such as letters and
numbers.
Note
The View Log File function can be found under this path: System> View Log File.
- 52 -
4.3.14.2 View User Information
The View User Information function can be found under this path: System> View User Information.
The Administrator can view each added user’s login information and privileges (refer to the section
Security).
- 53 -
Get User Information
All the users in the network will be listed in the <User information> zone, as
“User: 4321.” It indicates that one user’s login username is “User”, and password is “4321”.
Therefore, it denotes the user is granted privileges of I/O access, Camera control and Listen.
The View Parameters function can be found under this path: System> View Parameter.
Reboot
Click on the “Reboot” button, and the system will restart without changing current settings.
- 55 -
4.3.16 Software Version
The current software version is displayed in the software version page, which is shown as the figure
below.
- 56 -
4.3.17 Software Upgrade
Software upgrade can be carried out in the “Software Upgrade” page as shown below.
NOTE: Make sure the upgrade software file is available before carrying out software
upgrade.
Step 1: Click “Browse” and select the binary file to be uploaded, ex.Userland.jffs2.
- 57 -
NOTE: Do not change the upgrade file name, or the system will fail to find the file.
Step 2: Pull down the upgrade binary file list and select the file you want to upgrade; in this case,
select “userland.jffs2.”
Step 3: Press “Upgrade”. The system will first check whether the upgrade file exists or not, and then
begin to upload the upgrade file. Subsequently, the upgrade status bar will display on the page. When it
runs to 100%, the upgrade process is finished.
- 58 -
After the upgrade process is finished, the viewer will return to Home page.
Step 5: Click “Control Panel”, and then double click “Add or Remove Programs.” In the “Currently
install programs” list, select “DCViewer” and click the button “Remove” to uninstall the existing DC
Viewer.
Step 6: Open a new web browser, re-login the IP Camera, and then allow the automatic download of
DC Viewer.
- 59 -
4.3.18 Maintenance
The Maintenance setting can be found under this path: System> Maintenance.
Users can export configuration files to a specified location and retrieve data by uploading an existing
configuration file to the IP Camera.
Export
Users can save the system settings by exporting the configuration file (.bin) to a specified location for
future use. Click on the <Export> button, and the popup File Download window will come out. Click on
<Save> and specify a desired location for saving the configuration file.
Upload
To copy an existing configuration file to the IP Camera, please click on <Browse> to select the
configuration file first, and then click on the <Upload> button for uploading.
- 60 -
4.4 Video and Audio Streaming Settings
Press the tab ”Streaming” in the top of the page, and the configurable video and audio items will display
in the left column. In Streaming, the Administrator can configure specific video resolution, video
compression mode, video protocol, audio transmission mode, etc. Further details of these settings will
be specified in the following sections.
Video Format
Under Video Resolution section, the available video resolution formats are including MJPEG and H.264.
Please refer to the Video Format for more combination details.
Suppose the displayed image of the IP Camera is shown as the figure below.
To rotate the image, users can select <Flip>, for instance. Then the displayed image will be reversed as
shown below.
• Mirror
If select <Mirror>, the image will be rotated horizontally.
- 62 -
• 90 Degree Counter-/clockwise
Selecting <90 Degree Counter-/clockwise> will make the image 90° counter-/clockwise inversed.
GOV Settings
Users can set the GOV length to determine the frame structure (I-frames and P-frames) in a video
stream for saving bandwidth. Longer GOV means decreasing the frequency of I-frames. Click <Save>
to confirm the GOV setting.
H.264 Profile
Users can set each H.264 Profile to <Baseline Profile>, <Main Profile> or <High Profile> according to
its compression needs. With the same bit rate, the higher the compression ratio, the better the image
quality is. The default setting is <Main Profile>.
- 63 -
Users can select a proper MJPEG/H.264 compression mode on the video compression page,
depending on the application.
MJPEG Q (Quality) factor
Higher value implies higher bit rates and higher visual quality. The default setting of MJPEG Q factor is
35; the setting range is from 1 to 70.
ROI stands for Region of Interest. This function allows users to select specific monitoring region for 2nd,
3rd and 4th streams, instead of showing the full image.
NOTE: This function is only available when triple streams or above is selected under Video
Resolution in Video Format Setting.
- 64 -
Check the box and Stream 2 ROI Window will be displayed. To change the size of Stream 2 ROI
Window, move the mouse cursor to the edge of the frame and draw it outward/inward. Moving the
mouse to the center of the frame can shift the frame to the intended location.
Video frame rate is for setting the frames per second (fps) if necessary.
- 66 -
4.4.6 Video Mask
The Video Mask setting can be found under this path: Streaming> Video Mask.
NOTE: It is suggested to set the Video Mask twice bigger than the object.
• Cancel a Mask
Uncheck the checkbox of the Video Mask meant to be deleted, and the selected mask will disappear
from the Live Video pane instantly.
Mask Setting
• Mask color
The selections of Mask color include red, black, white, yellow, green, blue, cyan, and magenta. Click
<Save> to confirm the setting.
- 67 -
Transmission Mode
• Simplex (Listen only)
In the Listen only Simplex mode, the local/remote site can only listen to the other site.
• Disable
Select the item to turn off the audio transmission function.
Bit Rate
Selectable audio transmission bit rate include 16 kbps (G.726), 24 kbps (G.726), 32 kbps (G.726), 40
kbps (G.726), uLAW (G.711) and ALAW (G.711). Both uLAW and ALAW signify 64 kbps but in different
compression formats. Higher bit rate will let higher audio quality and require bigger bandwidth.
- 68 -
4.5 Camera Settings
The figure below is the camera configuration page. Details of each parameter setting are described as
follows.
NOTE: Camera settings and buttons below the screen vary among different types of
camera.
- 69 -
The exposure is the amount of light received by the image sensor and is determined by the width of
lens diaphragm opening, the amount of exposure by the sensor (shutter speed) and other exposure
parameters. With this item, users can define how the Auto Exposure function works.
Auto Mode
Manual Mode
z Fixed Shutter Mode
In this mode, fixed shutter speed could be selected from the dropdown menu. The shutter speed range
is from 1/10000 to 1 (1/1.5) sec. with 19 (18) options. Users could select suitable shutter speed
according to the environmental illumination.
A camera needs to find reference color temperature, which is a way of measuring the quality of a light
source, for calculating all the other colors. The unit for measuring this ratio is in degree Kelvin (K).
Users can select one of the White Balance Control modes according to the operating environment. The
following table shows the color temperature of some light sources for reference.
- 70 -
Light Sources Color Temperature in K
Cloudy Sky 6,000 to 8,000
Noon Sun and Clear Sky 6,500
Household Lighting 2,500 to 3,000
75-watt Bulb 2,820
Candle Flame 1,200 to 1,500
Manual Mode
In this mode, users can change the White Balance value manually. Users can select a number between
0 ~127 of “Rgain/ Bgain” item to gain the red/ blue illuminant on the Live Video Pane.
Brightness
Users can adjust the image’s brightness by adjusting the item. Please select ranging from -12 to +13.
To increase video brightness, select a bigger number. Click on <√ > to confirm the new setting.
- 71 -
Sharpness
Increasing the sharpness level can make the image looked sharper; especially enhance the object’s
edge. Please select ranging from +0 to +15. Click on < √ > to confirm the new setting.
Contrast
Camera image contrast level is adjustable; please select ranging from -6 to +19. Click on < √ > to
confirm the new setting.
Saturation
Camera image saturation level is adjustable; please select ranging from -6 to +19. Click on < √ > to
confirm the new setting.
Hue
Camera image hue level is adjustable; please select ranging from -12 to +13. Click on < √ > to confirm
the new setting.
4.5.4 Backlight
The Backlight Setting can be found under this path: Camera> Backlight.
The Backlight Compensation function prevents the center object from being too dark in surroundings
where excessive light is behind the center object. Click on < √ > to confirm the new setting.
The camera’s digital zoom is adjustable from x2 to x8. Click on < √ > to confirm the new setting.
- 72 -
The Wide Dynamic Range (WDR) function is for solving high contrast or changing light issues so that
enhances better video display. The WDR is adjustable from Low, Mid to Hi. Higher level of WDR
represents wider dynamic range, so that he IP Camera can catch a greater scale of brightness. Click on
<√ > to confirm the new setting.
The IP Camera provides multiple <Noise Reduction> options for delivering optimized image quality
especially in extra low-light conditions.
Different level options for 3D Noise Reduction (3DNR) include Low, Mid and High. Higher level of 3DNR
generates relatively enhanced noise reduction.
The proprietary Smart Picture Quality (SPQ) video processing method could drastically minimum
motion blur and reduce noise especially in low-light environment. The combination of SPQ and 3DNR
at different level further yields exceptional video performance in various conditions.
The Noise Reduction function is configurable with the following options: 3DNR Low, 3DNR Mid, 3DNR
Hi, SPQ, SPQ + 3DNR Low, SPQ + 3DNR Mid, to SPQ + 3DNR Hi.
Select the video format that matches the present TV system. Click on < √ > to confirm the new setting.
- 73 -
4.6 Logout
Press the tab “Logout” in the top of the page, and the login window will pop up. This enables login with
another user name.
- 74 -
Appendix A: IP Camera Specifications
Video Specification
Image Sensor 1/2.7” Progressive CMOS
Lens 4 mm, F1.5
Minimum illumination 0.2 Lux @ F1.2
View Angle (Horizontal / Vertical) 66 / 52 Degree
Scan Method Progressive
Video Encoder H.264 / M-JPEG
Rate Control VBR (Variable Bit Rate)
Video Resolution H.264 1080p / 720p
M-JPEG 1080p / 720p / D1 / CIF
Frame Rate 15fps for 1080p
30fps for all resolutions
30fps for other resolutions
Image Control AWB, AES
Audio Specification
Audio Codec G.711, G.726
Environment Specifications
Power Requirement IEEE 802.3af
Dimension (W x D x H) Φ110 x 50 mm
Weight 180g
Power Consumption 3.8W max.
Operating Temperature 0 ~ 50 Degree C
Operating Humidity 10 ~ 90% (non-condensing)
Emission CE, FCC
- 75 -
Appendix B: Internet Security Settings
If ActiveX control installation is blocked, please either set Internet security level to default or change
ActiveX controls and plug-ins settings.
Step 4: Down the page, press “Default Level” (see the figure above) and click “OK” to confirm the
setting. Close the browser window, and open a new one later when accessing the IP Camera.
Step 5: Under “ActiveX controls and plug-ins”, set ALL items (as listed below) to <Enable> or
<Prompt>.
- 77 -
ActiveX controls and plug-ins settings:
1. Automatic prompting for ActiveX controls
2. Binary and scrip behaviors
3. Download signed ActiveX controls
4. Download using ActiveX controls
5. Initialize and script ActiveX not marked as
safe
6. Run ActiveX controls and plug-ins
7. Script ActiveX controls marked safe for
scripting
Step 6: Click <OK> to accept the settings and close the <Security> screen.
Step 7: Click <OK> to close the Internet Options screen.
Step 8: Close the browser window, and restart a new one later for accessing the IP Camera.
- 78 -
Appendix C: DC Viewer Download Procedure
The procedure of DC Viewer software download is specified as follows.
Step 1: In the DC Viewer installation page, click “Next” for starting installing.
Step 2: Setup starts. Please wait for a while until the loading bar runs out.
- 79 -
Step 3: Click “Finish” to close the DC Viewer installation page.
- 80 -
Appendix D: Frequently Asked Questions
The default IP address is 192.168.0.20, and you could use the Device Search utility on the
Ans: bundled CD to obtain the current IP address of IP camera. Please refer to the user’s manual
for more detail information.
The LAN socket of IP Camera is compliant with IEEE802.3af standard PoE interface, and IP
Ans:
Camera is necessary supplied power through PoE Switch/Hub device.
Use the L-type spanner in the bundled package to unscrew the cover. Loosen the focus fixed
Ans: screw, and rotate the lens counter-/clockwise to adjust focus; loosen the tilt fixed screw, and
adjust the camera’s tilt angle. You could get detail descriptions on the user’s manual.
The Reset button at the side of lens. Use the L-type spanner in the bundled package to
Ans:
unscrew the cover at first, and press the button with a proper tool to default setting.
Please according to your local TV system and go to [Camera] page to select NTSC or PAL
Ans:
video format.
- 81 -